05 Iprc1plus Coat Eng r

8/12/2019 05 Iprc1plus Coat Eng r

1/56

Please read this guide before operating this product.After you finish reading this guide, store it in a safe place for future reference. ENG

Coating GuideCoating Guide


2/56


3/56

imagePRESS C1+Coating Guide


4/56

Manuals for the MachineThe manuals for this machine are divided as follows. Please refer to them for detailed information.* Indicates the manuals supplied with optional equipment. Depending on the system configuration and

product purchased, some manuals may not be needed.Guides with this symbol are printed manuals. CD-ROM

Guides with this symbol are included on the accompanyingCD-ROM.

Quick Reference for Basic OperationsFor Basic Operations Basic FeaturesFor Additional Functions To Suit Your Needs

Easy Operation Guide CD-ROM

Case Example Instructions on Clear Coating Case Examples forClear Coating

CD-ROM

Basic Information User's Guide Basic Operations Troubleshooting Reference Guide CD-ROM

Coating Instructions Coating Guide(This Document)

CD-ROM

Copying and Mail Box Instructions Copying and Mail BoxGuide

CD-ROM

Sending Instructions Sending Guide* CD-ROM

Remote User Interface Instructions Remote UI Guide CD-ROM

Network Connectivity and Setup Instructions Network Guide CD-ROM

Necessary Operations before Scanning fromthe Windows Computers and Instructions onScanning

Network ScanGear Guide CD-ROM

Windows Network ScanGear Installation andInstructions Network ScanGear

Installation Guide* CD-ROM

PS/PCL/UFR II Printer and Direct PrintingInstructions PS/PCL/UFR II Printer

Guide* CD-ROM


5/56

Job Hold Instructions Job Hold Guide* CD-ROM

Necessary Operations before Printing from

the Windows Computers and Instructions onPrinting

Windows Printer DriverGuide CD-ROM

Windows Printer Driver Installation andInstructions Printer Driver Installation

Guide* CD-ROM

Necessary Operations before Printing fromthe Macintosh Computers and Instructionson Printing

Mac Printer Driver Guide CD-ROM

Mac OS X PS Printer Driver Installation andInstructions Mac PS Driver Guide* CD-ROM

Mac OS X UFR II Printer Driver Installationand Instructions Mac UFR II Driver Guide* CD-ROM

Installing MEAP Applications and Using theLogin Service MEAP SMS Administrator

Guide CD-ROM

To view the manual in PDF format, Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed onyour system, please download it from the Adobe Systems Incorporated website.


6/56

How This Manual Is Organized

Introduction to the Coating Functions

Coating Features

Chapter 1

Chapter 2

Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions. However, as we are constantly improving ourproducts, if you need an exact specification, please contact Canon.


7/56

v

Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viSymbols Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viKeys Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viDisplays Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Chapter 1 Introduction to the Coating Functions

Coating Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Coating Features Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Flow of Coating Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Loading Preprinted Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8

Selecting Preprinted Paper (Paper Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-9Selecting Preprinted Paper Manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10Using the Stack Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Specifying the Number of Sheets/Copies (Enter No. of Sheets/Copies) . . . 1-15

Collating Coated Paper (Finishing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16Page Order (Collate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21Page Order (Staple). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22

Coating Both Sides of Preprinted Paper (2-Sided). . . . . . . . . . . . . . . . . . . . . 1-24

Chapter 2 Coating Features

Coating Full Surface of Preprinted Paper (Clear Coat Entire Page) . . . . . . . . 2-2

Coating Certain Section of Preprinted Paper(Clear Coat Form Composition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Cancelling a Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8Using the Touch Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8Using the System Monitor Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Reserving Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10Reserving Coating Jobs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Reserving Coating Jobs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11Using the Stack Bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Checking the Result of Coating (Sample Coat) . . . . . . . . . . . . . . . . . . . . . . . 2-19


8/56

vi

PrefaceThank you for purchasing the Canon imagePRESS C1+. Please read this manual thoroughlybefore operating the machine to familiarize yourself with its capabilities, and to make themost of its many functions. After reading this manual, store it in a safe place for futurereference.

How to Use This Manual

Symbols Used in This ManualThe following symbols are used in this manual to explain procedures, restrictions,handling precautions, and instructions that should be observed for safety.

IMPORTANT Indicates operational requirements and restrictions. Be sure to readthese items carefully to operate the machine correctly, and avoiddamage to the machine.

NOTE Indicates a clarification of an operation, or contains additionalexplanations for a procedure. Reading these notes is highlyrecommended.

Keys Used in This ManualThe following symbols and key names are a few examples of how keys to bepressed are expressed in this manual:

Touch Panel Display Keys: [Key Name]

Control Panel Keys: Key icon

Examples: [Cancel]

[Done]

Examples:


9/56

vii

Displays Used in This ManualScreen shots of the touch panel display used in this manual are those taken whenthe following optional equipment is attached to the imagePRESS C1+: the ColorImage Reader-H1, Feeder (DADF-R1) Saddle Finisher-AA2, Punch Unit-L1, ColorUniversal Send Kit, and Color UFR II/PCL/PS Printer Kit.

Note that functions that cannot be used depending on the model or options, are notdisplayed on the touch panel display.

The keys which you should press are marked with a , as shown below.

When multiple keys can be pressed on the touch panel display, all keys are marked.Select the keys which suit your needs.

Press this key for operation.

Press [Coating].


10/56

viii


11/56

CHAPTER

1-1

1Introduction tothe Coating FunctionsThis chapter describes an introduction and the basic features of the Coating functions.

Coating Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Coating Features Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Flow of Coating Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Loading Preprinted Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Selecting Preprinted Paper (Paper Select). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9Selecting Preprinted Paper Manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10Using the Stack Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11

Specifying the Number of Sheets/Copies (Enter No. of Sheets/Copies) . . . . . . . . . . . . 1-15

Collating Coated Paper (Finishing). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16Page Order (Collate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21Page Order (Staple) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-22

Coating Both Sides of Preprinted Paper (2-Sided) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24


12/56

Coating Functions1-2

IntroductiontotheCoatingFunctions

1

Coating Functions

The Coating functions enable you to coat the paper that already has printing on it(preprinted paper) with the clear toner. You can coat the full surface or certainsection of preprinted paper. For these functions, each toner (black, cyan, magenta,or yellow) is not used, only the clear toner is used for coating.

Clear Coat Entire PageThis mode enables you to coat the full surface of preprinted paper. For details, see"Coating Full Surface of Preprinted Paper (Clear Coat Entire Page)," on p. 2-2 .

ClearCoating

PreprintedPaper Print

Preprinted Paper


13/56

Coating Functions 1-3

Clear Coat Form CompositionThis mode enables you to coat the certain section of preprinted paper. To use the ClearCoat Form Composition mode, the image form must be stored in the machine beforehand.For details, see "Coating Certain Section of Preprinted Paper (Clear Coat FormComposition)," on p. 2-4 .

Clear Image Preprinted Paper PrintImage Form

Preprinted Paper


14/56

Coating Features Screen1-4


1

Coating Features Screen

Coating Features ScreenThe screen below, which appears when [Coating] is selected, is called the CoatingFeatures screen.

a Clear Coat Entire PagePress to coat the full surface of preprinted paper.

b Clear Coat Form Comp.Press to coat the certain section of preprintedpaper.

c Paper SelectPress to select a paper source to load thepreprinted paper.

d FinishingPress to select the Collate or Staple mode.

e 2-SidedPress to coat both sides of a sheet of preprintedpaper.

f Enter No. of SheetsPress to specify the number of sheets per one copyyou want to coat.

g Enter No. of CopiesPress to specify the number of copies you want tocoat.

h Sample CoatPress to coat a sample of the document to checkthe result of coating.

i Start CoatingPress to start coating.

j System MonitorPress to check progress of a printing orconsumables.

ab

ed

fg

ij

hc


15/56

Flow of Coating Operations 1-5

Flow of Coating Operations

This section describes the flow of basic coating operations.

NOTE Before using the Coating functions, it is useful to read the following topics:

- Main power and control panel power (See Chapter 1, "Before You Start Using ThisMachine," in the Reference Guide .)

- Entering characters from the touch panel display (See Chapter 2, "Basic Operations," inthe Reference Guide .)

- Routine maintenance (See Chapter 7, "Routine Maintenance," in the Reference Guide .) If you are using a login service, log in and log out using the procedure for the login

service you are using before and after operating the machine.

- If you are using Department ID Management with the optional Card Reader-C1, seeChapter 3,"Optional Equipment," in the Reference Guide .- If you are using Department ID Management, see Chapter 2, "Basic Operations," in the

Reference Guide .- If you are performing user authentication using the SSO-H or SSO login service, see

Chapter 2, "Basic Operations," in the Reference Guide . To cancel all settings, press .

1 Press [Coating].


16/56

Flow of Coating Operations1-6


1

2 Load the preprinted paper into a paper source.

NOTE The illustration above shows that the preprinted paper is loaded into the paper

drawer. For instructions on loading preprinted paper, see "Loading Preprinted Paper," on p.

1-8 .

3 Select the loaded preprinted paper.

NOTEFor instructions on selecting preprinted paper, see "Selecting Preprinted Paper(Paper Select)," on p. 1-9 .


17/56

Flow of Coating Operations 1-7

4 Specify the [Clear Coat Entire Page] or [Clear Coat FormComp.] mode settings.

NOTE For instructions on the Clear Coat Entire Page mode, see "Coating Full Surface of

Preprinted Paper (Clear Coat Entire Page)," on p. 2-2 . For instructions on the Clear Coat Form Composition mode, see "Coating Certain

Section of Preprinted Paper (Clear Coat Form Composition)," on p. 2-4 .

5 Specify the number of sheets and copies to be coated.

NOTEFor instructions on specifying the number of sheets and copies, see "Specifying theNumber of Sheets/Copies (Enter No. of Sheets/Copies)," on p. 1-15 .

6 Press [Start Coating].


18/56

Loading Preprinted Paper1-8


1

Loading Preprinted Paper

The side of preprinted paper to be coated (coated surface) differs depending on thepaper source into which you load the preprinted paper. To coat the side which hasprinting on it, you must load the preprinted paper with correct side up or down. Also,if you load multiple sheets of preprinted paper, be sure to check how the preprintedpaper is arranged. The following table shows that the combination of coated surfacein each paper source and arrangement of the preprinted paper.

NOTEIf you load two-sided preprinted paper, set front side to coated surface.Example:If you load two-sided preprinted paper, load the paper face down.- If you load multiple sheets of preprinted paper into the paper drawer, arrange them in

page order with first page on top.- For more information on paper types, see Chapter 2, "Basic Operations," in the

Reference Guide .

Paper Source

Paper Drawer Stack Bypass Paper Deck-AA1

Coated surface Face down Face up Face up

Arrangement In page order withfirst page on top

In page order withfirst page on top

In page order withfirst page on top


19/56

Selecting Preprinted Paper (Paper Select) 1-9

Selecting Preprinted Paper (Paper Select)

IMPORTANT When coating special types of paper, such as heavy paper or transparencies, be sure to

correctly set the paper type, especially if you are using heavy paper. If the type of paperis not set correctly, it could adversely affect the quality of the image. Moreover, the fixingunit may become dirty, or the paper could jam, and a service repair may be needed.

Make sure to load the same sized preprinted paper. You cannot use different sizedsheets of preprinted paper together.

NOTE If you select [Transparency] or [Labels], make sure that you do not specify any Finishing

modes (Collate or Staple). If Stack Bypass Standard Settings in Common Settings (from the Additional Functions

screen) is set to 'On', and the paper size/type have been stored, the selected paper size/ type are displayed on the screen. (See Chapter 4, "Customizing Settings," in theReference Guide .)

For instructions on loading preprinted paper into the stack bypass, see Chapter 2, "BasicOperations," in the Reference Guide .

For more information on paper types, see Chapter 2, "Basic Operations," in theReference Guide .

For instructions on entering values in inches, see Chapter 2, "Basic Operations," in theReference Guide .


20/56

Selecting Preprinted Paper (Paper Select)1-10


1

Selecting Preprinted Paper Manually

1 Load the preprinted paper Press [Paper Select].

2 Select the paper source for the preprinted paper.

NOTE The paper sizes/types are indicated by icons on the touch panel display, in the

order in which they are loaded in the paper drawers. Icons indicating the type of paper loaded in each paper drawer can be displayed on

paper selection screens, if you store that information into the machine beforehand.(See Chapter 4,"Customizing Settings," in the Reference Guide .)

indicates that the paper is loaded vertically, and indicates that the paper isloaded horizontally. The suffix (such as in A4R) used in paper sizedesignations indicates that the paper is loaded in a paper drawer or the stackbypass horizontally.

If you press , the detailed information of the selected paper is displayed.

3 Press [Done].


21/56


Using the Stack Bypass

1 Load the preprinted paper Press [Paper Select].

2 Select [Stack Bypass].

NOTEIf you want to select the stack bypass when a paper size/type is already selectedfor the current or reserved job, press [Stack Bypass Settings] to specify the desiredpaper size/type.


22/56



1

If you want to select a standard paper size:

Select the desired paper size press [Next].

NOTETo select an inch paper size, press [Inch-size].

Select the desired paper type press [OK].


23/56


If the desired paper type is not displayed, press [Detailed Settings] select thepaper type from the list press [OK].

If you are coating the back side of the paper, press [2nd Side of 2-Sided Page].

NOTE [Transparency] can be selected only if [A4] is selected as the paper size. You can register paper types that are not displayed on the detailed settings list in

[Selecting the Paper Type]. For more information on storing the paper type, see

Chapter 6, "System Manager Settings," in the Reference Guide .

If you want to select a nonstandard paper size:

Press [Irreg. Size].

Press [X] (horizontal axis) enter a value.

Press [Y] (vertical axis) enter a value.

Press [OK].

You can also press a size key in which a paper size is registered ([S1] to [S5]),instead of entering a value.

NOTETo recall a paper size from a size key ([S1] to [S5]), it is necessary to register apaper size in that key beforehand. For instructions on registering a paper size, seeChapter 4, "Customizing Settings," in the Reference Guide .


24/56



1

Press [Next].

Select the desired paper type press [OK].

If the desired paper type is not displayed, press [Detailed Settings] select thepaper type from the list press [OK].

If you are coating the back side of the paper, press [2nd Side of 2-Sided Page].

IMPORTANTIf you select a nonstandard paper size, the Offset Collate, Staple, or 2-Sided modecannot be specified.

3 Press [Done].


25/56

Specifying the Number of Sheets/Copies (Enter No. of Sheets/Copies) 1-15

Specifying the Number of Sheets/Copies(Enter No. of Sheets/Copies)

If you are coating paper that already has printing on it (preprinted paper), there areno data to be used as original, such as copy originals or documents in an inbox.The preprinted paper itself is original and paper to be coated. Therefore, it isnecessary to specify the number of sheets and copies you want to coat beforehand.


NOTEFor instructions on loading preprinted paper, see "Loading Preprinted Paper," on p.1-8.

2 Press [Enter No. of Sheets] Enter the number of sheets tobe coated using - (numeric keys).

3 Select [Enter No. of Copies] Enter the number of copies tobe coated using - (numeric keys).

IMPORTANTIf you collate the multiple copies of outputs by the copy sets, be sure to enter thenumber of copies to be coated. If you do not specify the number of copies, outputsare not collated with setting in the Finishing mode. (See "Collating Coated Paper(Finishing)," on p. 1-16 .).


26/56

Collating Coated Paper (Finishing)1-16


1

Collating Coated Paper (Finishing)

The Finishing modes can be selected to collate the outputs in various ways, eitherby pages or copy sets.

IMPORTANT The Finishing modes cannot be set if transparencies, labels, or tab paper is selected. The Finishing modes can be set only if an optional finisher is attached. If you set the Staple or Hole Punch mode, the side of the paper which is printed on will

always be output face down.

NOTE For information for the optional finishers, see Chapter 3, "Optional Equipment," in the

Reference Guide . To cancel this setting, press [Finishing] [Cancel].


27/56

Collating Coated Paper (Finishing) 1-17

The table below shows all the finishing features that are available with eachdifferent optional unit, and the paper sizes that can be used.

*1 Holes can only be punched in A4R paper using the Punch Unit-L1/P1.

: Available: Unavailable

Optional Unit OffsetStaple

HolePunchCorner Double Saddle

StitchCopy Tray

Finisher-AA1 A3,A4,A4R

A3,A4R

(30 sheets),A4

(50 sheets)

A3,A4R

(30 sheets),A4

(50 sheets)

Finisher-AA1 andPunch Unit-L1/

N1/P1A3,A4,A4R

A3,

A4R (30 sheets),

A4(50 sheets)

A3,

A4R (30 sheets),

A4(50 sheets)

A3,A4,

A4R *1

SaddleFinisher-AA2

A3,A4,A4R

A3,A4R

(30 sheets),A4

(50 sheets)

A3,A4R

(30 sheets),A4

(50 sheets)

305 mm x457 mm,A3, A4R

(15 sheets)

SaddleFinisher-AA2 and

Punch Unit-L1/ N1/P1

A3,A4,A4R

A3,A4R

(30 sheets),A4

(50 sheets)

A3,A4R

(30 sheets),A4

(50 sheets)

305 mm x457 mm,A3, A4R

(15 sheets)

A3,A4,

A4R *1


28/56



1

If the Collate Mode Is Set:The copies are automatically collated into sets arranged in page order. The coatedpreprinted paper is output as follows:

If the Staple Mode Is Set:The copies are automatically collated into sets arranged in page order and stapled. Thecoated preprinted paper is output as follows:

If you select [Corner] (Top Left):

Preprinted Paper Coating 1Three Copiesof Each Page

Collated inPage Order

Coating 2 Coating 3

Preprinted PaperThree Copiesof Each PageCollated inPage Order

Coating 1 Coating 2 Coating 3


29/56


If you select [Double] (Left):

If you select [Saddle Stitch]:

IMPORTANT

The accuracy of folds created in the Saddle Stitch mode may vary, depending on thepaper type and the number of sheets.

NOTETo use the Saddle Stitch mode, the original (stored document) must already be in bookletform, as shown in the illustration above. (See Chapter 4, "Special Copying and Mail BoxFeatures," in the Copying and Mail Box Guide .)

Three Copiesof Each Page


Preprinted Paper Coating 1 Coating 2 Coating 3

Preprinted Paper

Three Copiesof Each Page


Coating 1 Coating 2 Coating 3


30/56



1

If No Finishing Mode Is Set:If the Collate and Staple modes are not set, coated preprinted paper is output as follows:

If the Hole Punch Mode Is Set:The machine punches two or four holes in the output.

If the Offset Mode Is Set:The copies are slightly offset vertically in the output tray as follows: (You can also specifythe number of copy sets to offset.)

Preprinted Paper Coatings

Preprinted Paper Coating

Preprinted Paper Coatings


31/56


Page Order (Collate)

1 Load the preprinted paper into a paper source press[Finishing].

NOTEFor instructions on loading preprinted paper, see "Loading Preprinted Paper," on p.1-8 .

2 Press [Collate (Page order)].

If you want to make hole punches, press [Hole Punch].

3 Press [OK].

The optional Finisher-AA1 orSaddle Finisher-AA2 andPunch Unit-L1 are attached.


32/56



1

Page Order (Staple)

IMPORTANTWhen coating special types of paper, such as heavy paper or transparencies, be sure tocorrectly set the paper type, especially if you are using heavy paper. If the type of paperis not set correctly, it could adversely affect the quality of the image. Moreover, the fixing

unit may become dirty, or the paper could jam, and a service repair may be needed.

1 Load the preprinted paper into a paper source press[Finishing].

If necessary, see the screen shot in step 1 of "Page Order (Collate)," on p. 1-21 .

2 Press [Staple].If you want to make hole punches, press [Hole Punch].

If the optional Finisher-AA1 is attached:

Press [Next].

Select the stapling type ([Corner] or [Double]) select the stapling position press [OK].


33/56


34/56

Coating Both Sides of Preprinted Paper (2-Sided)1-24


1

Coating Both Sides of Preprinted Paper (2-Sided)

This mode enables you to coat both sides of a sheet of preprinted paper. You canspecify the desired type of two-sided orientation, [Book Type] or [Calendar Type] forthis mode. By specifying the type of two-sided orientation, the image form can besuperimposed on collect position when you superimpose the image form on bothsides of the preprinted paper with the Clear Coat Form Composition mode.

NOTETo cancel this setting, press [2-Sided Original] [Cancel].

1 Load the preprinted paper into a paper source press[2-Sided].NOTE

For instructions on loading preprinted paper, see "Loading Preprinted Paper," on p.1-8 .

2 Select the type of two-sided orientation press [OK].Details of each item are shown below.

[Book Type]: The front and back sides of the original will have the same

top-bottom orientation.[Calendar Type]: The front and back sides of the original will have oppositetop-bottom orientations.


35/56

CHAPTER

2-1

2Coating FeaturesThis chapter explains how to use the Coating features.

Coating Full Surface of Preprinted Paper (Clear Coat Entire Page). . . . . . . . . . . . . . . . . 2-2

Coating Certain Section of Preprinted Paper (Clear Coat Form Composition). . . . . . . . . 2-4

Cancelling a Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8Using the Touch Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8Using the System Monitor Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

Reserving Jobs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10Reserving Coating Jobs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

Checking the Result of Coating (Sample Coat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19


36/56

Coating Full Surface of Preprinted Paper (Clear Coat Entire Page)2-2

CoatingFeatures

2

Coating Full Surface of Preprinted Paper(Clear Coat Entire Page)

The Clear Coat Entire Page mode enables you to coat the full surface of preprintedpaper with the clear toner. Each toner (black, cyan, magenta, or yellow) is not used,only the clear toner is used for this mode.

NOTE If you select paper that has no printing on it, and copy/print on it with each toner (black,

cyan, magenta, yellow, or clear), see Chapter 4, "Special Copying and Mail BoxFeatures," in the Copying and Mail Box Guide . If you want to adjust the density of clear toner, see Chapter 6, "System Management

Settings," in the Reference Guide .

ClearCoating

PreprintedPaper Print

Preprinted Paper


37/56

Coating Full Surface of Preprinted Paper (Clear Coat Entire Page) 2-3



2 Select the loaded preprinted paper.NOTE

For instructions on selecting preprinted paper, see "Selecting Preprinted Paper(Paper Select)," on p. 1-9 .

3 Press [Clear Coat Entire Page].

4 Press [Enter No. of Sheets] to specify the number of sheets tobe coated.

5 Press [Enter No. of Copies] to specify the number of copies tobe coated.

6 If necessary, specify the Finishing or 2-Sided mode settings.

NOTE For instructions on the Finishing mode, see "Collating Coated Paper (Finishing),"

on p. 1-16 . For instructions on the 2-Sided mode, see "Coating Both Sides of Preprinted Paper

(2-Sided)," on p. 1-24 .



38/56

Coating Certain Section of Preprinted Paper (Clear Coat Form Composition)2-4

CoatingFeatures

2

Coating Certain Section of Preprinted Paper(Clear Coat Form Composition)

The Clear Coat Form Composition mode enables you to superimpose a previouslyscanned image as a clear image, which has been stored in the hard disk of themachine (image form), on the preprinted paper. Each toner (black, cyan, magenta,or yellow) is not used, only the clear toner is used for this mode.

IMPORTANT To use the Clear Coat Form Composition mode, the image form must be stored in the

machine beforehand. (See Chapter 4, "Customizing Settings," in the Reference Guide .) It is recommended that you scan the image form in the Black mode. You can also select the image form scanned in the Auto-Color Select mode or Full Color

mode. However, if you select the image form scanned in the Auto-Color Select mode orFull Color mode and use it as the clear image, colour sections of the clear image exceptfor black sections may become lighter or not be printed.

Up to 100 image forms can be stored. However, this number varies depending on thefree space of the hard disk.

Printing performance may not be optimal in the Clear Coat Form Composition mode,depending on the selected document and image form.

Clear Image Preprinted Paper PrintImage Form

Preprinted Paper


39/56

Coating Certain Section of Preprinted Paper (Clear Coat Form Composition) 2-5

NOTE If you select paper that has no printing on it, and copy/print on it with each toner (black,

cyan, magenta yellow or clear), see Chapter 4, "Special Copying and Mail BoxFeatures," in the Copying and Mail Box Guide .

Clear Coat Form Composition Coating is set to 'On' by default. If you want to change thesetting of Clear Coat Form Composition Coating, see Chapter 6, "System ManagementSettings," in the Reference Guide .





3 Press [Clear Coat Form Comp.].

4 Press [Settings] for the side you want to superimpose.To superimpose a different image on both sides of a sheet, it is necessary to setthe 2-Sided mode.

To superimpose the same image on both sides of the sheet, specify the settingsfor the front side press [Same as Front Side].


40/56

Coating Certain Section of Preprinted Paper (Clear Coat Form Composition)2-6

CoatingFeatures

2

5 Select the image form to be superimposed over the original press [OK].

To check the images stored as forms, Press [Preview].

To print a sample of the images stored as forms, Press [Check Print].

Image forms stored in the RGB colour format are indicated with a icon. Image

forms stored in the CMYK colour format are indicated with a icon. (Colourimage forms are indicated with a colour icon.)

Press [Details] to display the detailed information of the image form.

IMPORTANT Image form you can use is only one page. You can store the image form which

contains multiple pages from the printer driver, but the first page is used as animage form.

When [Preview] or [Check Print] is selected, the colour mode selected in storedimage form is applied.

If [Check Print] is pressed: Select the paper size press [Start Print].

Press [Cancel] to cancel the sample print


41/56

Coating Certain Section of Preprinted Paper (Clear Coat Form Composition) 2-7

6 Press [Done].

7 Press [Enter No. of Sheets] to specify the number of sheets tobe coated.

8 Press [Enter No. of Copies] to specify the number of copies tobe coated.

9 If necessary, specify the Finishing mode settings.

NOTE For instructions on the Finishing mode, see "Collating Coated Paper (Finishing),"

on p. 1-16 . For instructions on the 2-Sided mode, see "Coating Both Sides of Preprinted Paper

(2-Sided)," on p. 1-24 .



42/56

Cancelling a Job2-8

CoatingFeatures

2

Cancelling a Job

Using the Touch Panel Display

1 Press [Cancel] on the pop-up screen that appears while themachine is coating or waiting to coat.

The coating is cancelled.

Using the System Monitor Screen

1 Press [System Monitor].


43/56

Cancelling a Job 2-9

2 Press [Print Status] [Status] select the coating job thatyou want to cancel press [Cancel].

You cannot select multiple jobs and cancel them all at once. Select and cancelone job.

3 Press [Yes].The coating job is cancelled.

NOTEThe cancelled job is displayed as (No Good) on the Log screen.

4 Press [Done].The display returns to the Coating Features screen.


44/56

Reserving Jobs2-10

CoatingFeatures

2

Reserving Jobs

You can set the machine to coat the preprinted paper even while it is printing orwaiting to process a job.

IMPORTANTYou can not set the machine to coat the preprinted paper while the machine is coatingwith the Coating mode.

NOTE You can specify up to 32 documents to be reserved, including the current job. You can set different modes and paper sources, including the stack bypass, for each

reserved job.

Reserving Coating JobsReserved coating can be specified in the following cases:

While the Machine Is WaitingYou can specify settings for coating while the machine is in the waiting state, such aswhen the power is just turned ON, or after a paper jam is cleared. Coating automaticallybegins when the machine is ready.

NOTEYou can specify reserved coating while the machine is in the waiting state in the followingcases:- Between the time that the machine is turned ON and when it is ready to print- Between the time that the machine wakes up from the Energy Saver mode and when it

is ready to print- After a paper jam is cleared- After a cover on the main unit or an optional unit, such as a finisher, is opened and

closed

While the Machine Is Printing

You can specify settings for coating while the machine is printing. Coating automaticallybegins when the current job is complete.


45/56

Reserving Jobs 2-11

Reserving Coating Jobs

1 Press [Done] on the pop-up screen that appears while themachine is printing.

NOTE

Screen below is the Regular Copy Basic Features screen.

2 Press [Coating] to display the Coating Features screen.





5 Specify the Coating mode settings.



46/56

Reserving Jobs2-12

CoatingFeatures

2

Using the Stack Bypass Reserved printing using the stack bypass is possible only if paper is being fed fromthe stack bypass for the current job.

The following example assumes that A3 plain paper is being fed from the stackbypass for the current job, and that you are selecting A4 plain paper to be fed fromthe stack bypass for a reserved job.

IMPORTANTWhen coating special types of paper, such as heavy paper or transparencies, be sure tocorrectly set the paper type, especially if you are using heavy paper. If the type of paperis not set correctly, it could adversely affect the quality of the image. Moreover, the fixingunit may become dirty, or the paper could jam, and a service repair may be needed.

NOTE If Stack Bypass Standard Settings in Common Settings (from the Additional Functions

screen) is set to 'On', reserved coating can be performed only for the registered papersize and type. (See Chapter 4,"Customizing Settings," in the Reference Guide .)

For information on paper types, see Chapter 2, "Basic Operations," in the ReferenceGuide .

For instructions on entering values in inches, see Chapter 2, "Basic Operations," in theReference Guide .


47/56

Reserving Jobs 2-13

1 Press [Done] on the pop-up screen that appears while themachine is printing.

NOTEScreen below is the Regular Copy Basic Features screen.

2 Press [Coating] to display the Coating Features screen.

3 Set the desired coating modes Press [Paper Select] Press[Stack Bypass Settings].

Normally, when reserved copying is not being set, the Stack Bypass Settingsscreen is automatically displayed when paper is loaded into the stack bypass.


48/56


49/56

Reserving Jobs 2-15





Press [OK].You can also press a size key in which a paper size is registered ([S1] to [S5]),instead of entering a value.


Press [Next].

Select the desired paper type press [OK].If the desired paper type is not displayed, press [Detailed Settings] selectthe paper type from the list press [OK].

If you are coating the back side of the paper, press [2nd Side of 2-SidedPage].

The paper size/type currently loaded and the paper size/type reserved to beloaded are displayed, as shown on the screen below.

Paper Size/Type Sele c ted

Paper Size/TypeCurrently Loaded

Detailed Information


50/56

Reserving Jobs2-16

CoatingFeatures

2

NOTEIf there is more than one reserved job waiting to print, only the last paper size/typespecified for the reserved print job is shown on the Paper Select screen.

5 Press [Done].This completes the settings for reserving a print job using the stack bypass. Thesubsequent steps show you how to start coating and load paper into the stackbypass.


7 When it is time for the reserved coating job to be coated, loadthe specified paper into the stack bypass.

NOTE The specified paper size/type is displayed on the screen when it is time for the

reserved coating job to be coated. Make sure to load the same paper size and type selected in step 4 into the stack

bypass. Coating does not start if paper of a different size or type is loaded.


51/56

Reserving Jobs 2-17

8 Select the desired paper size and type.If the following screen is displayed, adjust the width of the slide guides specifythe paper size press [OK].

If the following screen is displayed, adjust the width of the slide guides to matchthe paper size stored in Stack Bypass Standard Settings, or set Stack BypassStandard Settings to 'Off' in Common Settings (from the Additional Functionsscreen). (See Chapter 4, "Customizing Settings," in the Reference Guide .)

IMPORTANTSet the paper size to the same size as the paper loaded in the stack bypass.


52/56

Reserving Jobs2-18

CoatingFeatures

2

If you want to select a standard paper size:

Select the desired paper size press [Next].

NOTETo select an inch paper size, press [Inch-size].

Select the paper type.If the desired paper type is not displayed, press [Detailed Settings] selectthe paper type from the list press [OK].






Press [OK].You can also press a size key in which a paper size is registered ([S1] to [S5]),instead of entering a value.


Press [Next].

Select the paper type press [OK].If the desired paper type is not displayed, press [Detailed Settings] selectthe paper type from the list press [OK].



53/56

Checking the Result of Coating (Sample Coat) 2-19

Checking the Result of Coating (Sample Coat)

Before coating multiple copies, you can coat a sample of it to check the results ofcoating.

IMPORTANT If an optional finisher is attached, [Sample Coat] appears only when you set to coat

multiple copies in the Collate, Offset Collate or Staple mode. If an optional finisher is not attached, [Sample Coat] appears when you set to coat

multiple copies.

1 Set the desired coating modes Press [Sample Coat].

IMPORTANT[Sample Coat] is not displayed if only one copy is set.


NOTE If you select [Specified Pages], specify the page numbers of the output. Note that

the page numbers of the output may be different from those of the storeddocument.

If you select [Specified Pages], the Staple, Hole Punch, or Booklet mode cannot beset.

You cannot change [All Pages] to [Specified Pages] or vice versa after the samplecoat is output.

If you select [Specified Pages], you cannot change the specified pages after thesample coat is output.


54/56

Checking the Result of Coating (Sample Coat)2-20

CoatingFeatures

2

3 Check the sample coat select [Start Coating] or [Cancel].

To coat the remaining coatings:

Press [Start Coating].

To cancel coating:

Press [Cancel].


55/56


56/56

CANON INC.30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanCANON U.S.A., INC.One Canon Plaza, Lake Success, NY 11042, U.S.A.CANON CANADA INC.6390 Dixie Road Mississauga, Ontario L5T 1P7, CanadaCANON EUROPA N.V.Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands(See http://www.canon-europe.com/ for details on your regional dealer)CANON LATIN AMERICA, INC.703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A.CANON AUSTRALIA PTY. LTD1 Thomas Holt Drive, North Ryde, Sydney, N.S.W. 2113, AustraliaCANON CHINA CO., LTD15F Jinbao Building No 89 Jinbao Street Dongcheng District Beijing 100005 China

05 Iprc1plus Coat Eng r

Documents

Transcript of 05 Iprc1plus Coat Eng r