05 Idu Accessories Product Description

8/10/2019 05 Idu Accessories Product Description

1/40

FlexiPacket Hub 800

R2.5

IDU Accessories Product Description

A25000-A0800-E028-01-76P1

Issue: 1 Issue date: May 2013

Nokia Siemens Networks is continually str iving to reduce the adverse environmental effects of

its products and services. We would like to encourage you as our customers and users to join

us in working towards a cleaner, safer environment. Please recycle product packaging and

follow the recommendations for power use and proper disposal of our products and their

components.

If you should have questions regarding our Environmental Policy or any of the environmental

services we offer, please contact us at Nokia Siemens Networks for any additional information.


2/40

2 A25000-A0800-E028-01-76P1



The information in this document is subject to change without notice and describes only the

product defined in the introduction of this documentation. This documentation is intended for the

use of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted

in any form or means without the prior written permission of Nokia Siemens Networks. The

documentation has been prepared to be used by professional and properly trained personnel,

and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes

customer comments as part of the process of continuous development and improvement of the

documentation.

The information or statements given in this documentation concerning the suitability, capacity,

or performance of the mentioned hardware or software products are given "as is" and all liability

arising in connection with such hardware or software products shall be defined conclusively and

finally in a separate agreement between Nokia Siemens Networks and the customer. However,

Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions

contained in the document are adequate and free of material errors and omissions. Nokia

Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which

may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO

EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMEN-

TATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT

LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS

OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR

THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and

other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark

of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright Nokia Siemens Networks 2013. All rights reserved.

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources

of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle

this product and only after having carefully read the safety information applicable to this

product.

The safety information is provided in the Safety Information section in the Legal, Safety

and Environmental Information part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur ProduktsicherheitVon diesem Produkt knnen Gefahren durch Laser, Elektrizitt, Hitzeentwicklung oder

andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch

geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-

anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter Sicherheitshinweise im Teil Legal,

Safety and Environmental Information dieses Dokuments oder dieses Dokumentations-

satzes.


3/40


4/40

4 A25000-A0800-E028-01-76P1



6.2 Key characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7 Dual-IDU accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.1 Dual-IDU shroud. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.2 Dual-IDU protection panel and optical splitter. . . . . . . . . . . . . . . . . . . . . 36

7.2.1 Protection panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.2.2 Optical splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.3 Dual-IDU power injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

8 FPH800 installation tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

9 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40


5/40

A25000-A0800-E028-01-76P1


5


List of FiguresFigure 1 WEEE label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 2 CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 3 MEF certified compliant logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 4 16-port E1/T1 Multi-Service card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 5 4-port GE RJ-45 card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 6 4-port GE SFP card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 7 2-port Power Injector card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 8 2-port FlexBus card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 9 2-port STM-1/4 MSC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 10 Electrical SFP module application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 11 Optical SFP module application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 12 GE electrical interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 13 75 ohm Coaxial Cable with MDR68 connectors . . . . . . . . . . . . . . . . . . 24Figure 14 32 pair 120 ohm cable with MDR68 connectors . . . . . . . . . . . . . . . . . . 25

Figure 15 FB cable application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 16 Power supply interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 17 Grouding cable assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 18 RJ45 patch panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 19 CC4 patch panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 20 BNC patch panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 21 USB key connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 22 Dual-IDU shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 23 Backplane of the shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 24 A protection panel with 2 optic splitters . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 25 Optic splitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 26 Power injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37


6/40

6 A25000-A0800-E028-01-76P1



List of TablesTable 1 Structure of this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 2 History of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 3 List of symbols and conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 4 16-port E1/T1 Multi-Service card cabling . . . . . . . . . . . . . . . . . . . . . . . . 13

Table 5 4-port GE RJ-45 cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 6 4-port SFP card cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 7 2-port Power Injector card cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 8 2-port FlexBus Card cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 9 2-port STM-1/4 MSC card cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 10 GE/FE electrical interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Table 11 Property of GE copper cable reel with length = 5 m . . . . . . . . . . . . . . . 19

Table 12 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 13 Properties for MM fiber patch cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Table 14 Properties for SM fiber patch cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 15 E1/T1 interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 16 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 17 FB cable and connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table 18 Power supply interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 19 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 20 Color code of power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 21 RJ45 patch panel characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 22 CC4 patch panel characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 23 BNC patch panel characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 24 Mechanical dimension and interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Table 25 USB key connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 26 Read/Write performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 27 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 28 Shroud characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 29 Protection panel characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table 30 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37


7/40


8/40

8 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionPreface

1.4 Symbols and conventions

The following symbols and mark-up conventions are used in this document:

Representation Meaning

fDANGER!

fWARNING!

fCAUTION!

A safety message indicates a dangerous situation where

personal injury is possible.

The keywords denote hazard levels with the following meaning:

DANGER!- Indicates a hazardous situation which, if not

avoided, will result in death or serious (irreversible) personal

injury.

WARNING!- Indicates a hazardous situation which, if not

avoided, could result in death or serious (irreversible) personal

injury.

CAUTION! - Indicates a hazardous situation which, if not

avoided, may result in minor or moderate (reversible) personal

injury.

wNOTICE: A property damage message indicates a hazard that may resultin equipment damage, data loss, traffic interruption, and so on.

g A note provides important information related to the topic, forexample, not obvious exceptions to a rule or side effects.

t A tip provides additional information related to the topic which isnot essential in the context, but given for convenience.

Bold

All names of graphical user interface (GUI) objects, such aswindows, field names, buttons, and so on.

Example: Select the Full Screencheck box and press OK.

Terms and abbreviations which are linked to an entry in the

glossary and list of abbreviations respectively

Important key words

Italic Files, folders, and file system paths.

Example:/usr/etc/sbin/ftpd.exe

Emphasized words

typewriter Input to be typed in a command line or a GUI field.

Examples:

ping -t 192.168.0.1

Enter Worldin the Domainfield.

Output from a command, error messages, content of a status

line, and so on

File content, such as program sources, scripts, logs, and

settings

Placeholders, for example as part of a file name or field value.

Examples:

.pngor :

Table 3 List of symbols and conventions


9/40

A25000-A0800-E028-01-76P1


9

IDU Accessories Product Description Preface

Screenshots of the graphical user interface are examples only to illustrate principles.

This especially applies to a software version number visible in a screenshot.

1.5 Waste electrical and electronic equipment (WEEE)

All waste electrical and electronic products must be disposed of separately from the

municipal waste stream via designated collection facilities appointed by the government

or the local authorities. The WEEE label (see Figure 1) is applied to all such devices.

Figure 1 WEEE label

The correct disposal and separate collection of waste equipment will help prevent poten-

tial negative consequences for the environment and human health. It is a precondition

for reuse and recycling of used electrical and electronic equipment.

For more detailed information about disposal of such equipment, please contact Nokia

Siemens Networks.

The above statements are fully valid only for equipment installed in the countries of the

European Union and is covered by the directive 2002/96/EC. Countries outside the

[square brackets] A key to be pressed on a PC keyboard, for example [F11].

Keys to be pressed simultaneously are concatenated with a +

sign, for example [CTRL]+[ALT]+[DEL].

Keys to be pressed one after another are concatenated with

spaces, for example [ESC] [SPACE] [M].

> The greater than symbol > is used to concatenate a series of

GUI items in order to depict a GUI path. This is an abridged pre-

sentation of a procedure to be carried out in order to perform an

action or display a window or dialog box.

Examples:

A simple menu path: File> Save as ...

A more complex GUI path:SURPASS TransNetwindow > Toolsmenu >

3R-Matrix Report command > 3R-Matrix Reportdialog box

x

(in card names)

For convenience, card names are sometimes listed with a lower

case x variable, in order to concisely represent multiple cards.

Example:

I01T40G-x (is to be interpreted as I01T40G-1 and I01T40G-2)

Representation Meaning

Table 3 List of symbols and conventions (Cont.)


10/40

10 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionPreface

European Union may have other regulations regarding the disposal of electrical and

electronic equipment.

1.6 RoHS complianceFlexiPacket Hub 800 complies with the European Union RoHS Directive 2002/95/EC on

the restriction of use of certain hazardous substances in electrical and electronic equip-

ment.

The directive applies to the use of lead, mercury, cadmium, hexavalent chromium, poly-

brominated biphenyls (PBB), and polybrominated diphenylethers (PBDE) in electrical

and electronic equipment put on the market after 1 July 2006.

Materials usage information on Nokia Siemens Networks Electronic Information

Products imported or sold in the Peoples Republic of China

FlexiPacket Hub 800 complies with the Chinese standard SJ/T 11364-2006 on the

restriction of the use of certain hazardous substances in electrical and electronic equip-ment. The standard applies to the use of lead, mercury, cadmium, hexavalent chro-

mium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in

electrical and electronic equipment put on the market after 1 March 2007.

1.7 CE compliance

FlexiPacket Hub 800 is in compliance with the essential requirements and other relevant

provisions of Directive: 2006/95/EC, 2004/108/EC, and 1999/5/EC.

Figure 2 CE marking

1.8 MEF compliance

FlexiPacket Hub 800 operating at the NNI delivers EPL, EVPL and E-LAN service

complies with the Metro Ethernet Forum MEF14 technical specification. FlexiPacket

Hub 800 operating at the UNI delivers EPL, EVPL and E-LAN service complies with the

Metro Ethernet Forum MEF9 technical specification.

The product is marked with the CE marking


11/40

A25000-A0800-E028-01-76P1


11

IDU Accessories Product Description Preface

Figure 3 MEF certified compliant logo


12/40

12 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionOverview

2 OverviewThe main accessories of FPH800 includes the following.

gAll accessories must be ordered separately. They are not in the default delivery ofFPH800.

2.1 FPH800 plug-in cards

FPH800 supports plug-in cards for carrying traffic coming from the co-located equip-

ment.

2.2 FPH800 connection accessaries

FPH800 can be connected to local traffic through the following types of accessories.

Cables and connectors for Ethernet copper interfaces.

Cables for Ethernet optical interfaces.

Cables for STM-1 optical interfaces.

Cables for E1 interfaces.

Cables and connectors for FB interfaces.

SFP modules are designed to support ATM, SDH, SONET, GE and Fiber Channel com-

munication standards.

2.3 FPH800 patch panels

Patch panel is used if the local equipment does not support MDR68 connector in E1/T1

traffic transmit. Patch panel works as a switcher between FPH800 mainboard and the

local equipment, which switches the signals from MDR68 connector to RJ45 connec-

tors, CC4 connectors or BNC connectors.

2.4 FPH800 dual-IDU accessaries

To support dual-IDU mode for FPH800s, some dedicated accessories have been intro-

duced (e.g., shroud, protection panel and optical splitter modules).

2.5 FPH800 USB key

FPH800 is equipped with a USB key for the backup of IDU configuration. It provides a

socket to host a 1 Gigabit USB key type. And the USB key is used for IDU/ODU config-

uration and software load backup. The USB key is pre-formatted of FAT mode in factory.

In case of Dual-IDU protected configuration, only one USB key is used, located in the

Main IDU.

2.6 FPH800 installation tools

The installation tool includes: Mounting bracket, ETSI N3 rack, 19-inch rack and rack

screws, nuts, etc.


13/40

A25000-A0800-E028-01-76P1


13

IDU Accessories Product Description FPH800 plug-in cards

3 FPH800 plug-in cardsFPH800 supports plug-in cards for carrying traffic coming from the co-located equip-

ment. The external cards can be placed in slot 1 and slot 2 on the FPH800 mainboard.

16-port E1/T1 Multi-Service Card

4-port GE RJ-45 Card

4-port SFP Card

2-port Power Injector Card

2-port FlexBus card

2-port STM-1/4 MSC Card

3.1 16-port E1/T1 Multi-Service card

16-port E1/T1 Multi-Service card is the PIU (Plug-in Unit) of the FPH800.

Figure 4 16-port E1/T1 Multi-Service card

3.2 4-port GE RJ-45 card

4-port GE RJ-45 card is the PIU of the FPH800, it provides extended 4 GE interfaces

based on 1000Base-T standard. If the GE interface is used as ODU interface, extra 2-

port Power Injector cardis needed.

Parameter Description

Interface 16 channels of E1/T1 interfaces

Cable type 32 pair 75 ohm impedance coaxial cable;

or 32 pair 120 ohm impedance coaxial

cable

Connector MDR68

Table 4 16-port E1/T1 Multi-Service card cabling


14/40

14 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionFPH800 plug-in cards

Figure 5 4-port GE RJ-45 card

3.3 4-port GE SFP card

4-port GE SFP card is the PIU of the FPH800, it provides extended 4 GE optical inter-

faces.

Figure 6 4-port GE SFP card

3.4 2-port Power Injector card

2-port Power Injector card supports 2 GE interfaces power feeding (1000Base-T).


Interface 4 10/100/1000BaseT electrical inter-

facesCable type CAT6 S/FTP

Connector Shielded RJ-45

Table 5 4-port GE RJ-45 cabling


Cable type single/multi mode fiber duplex

Connector type LC-LC duplex

Table 6 4-port SFP card cabling


15/40

A25000-A0800-E028-01-76P1


15

IDU Accessories Product Description FPH800 plug-in cards

Figure 7 2-port Power Injector card

3.5 2-port FlexBus card

2-port FlexBus card supports local FlexBus interfaces.

Figure 8 2-port FlexBus card

Parameter Ethernet ODU

Interface 2

10/100/1000BaseTEthernet electrical

interfaces & 2 ODU

interfaces

-

Cable type CAT6 S/FTP Double shielded, four twisted pairs, Cat-

5e cable compliant (for outdoor condition).

Each pin manages at least 24 AWG wire

diameter.

Connector type Shielded RJ45 Shielded RJ45 (towarding the power

injector card); amphenol (towarding the

Flexi-Packet Multi Radio)

Table 7 2-port Power Injector card cabling


Interface 2 FB optical interfaces

Table 8 2-port FlexBus Card cabling


16/40

16 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionFPH800 plug-in cards

3.6 2-port STM-1/4 MSC card

2-port STM-1/4 MSC card provides 2 X STM-1 or 2 X STM-4 interfaces. When the user

change the interface between STM-1 and STM-4, all services related to the interface

must be shut down.

The main functions of this card include MSP 1 + 1, EoS (Ethernet over GFP over SDH)

and Virtual concatenation (VC-4, VC-12).

Figure 9 2-port STM-1/4 MSC card

Cable type Coaxial cable, double shielded, or semi-

rigid

Connector FlexBus TNC


Table 8 2-port FlexBus Card cabling (Cont.)


Interface 2 STM-1 optical interfaces with SFP

module or 2 STM-4 optical interfaces

with SFP modules

Cable type Multi-mode fiber patch cord or single-

mode fiber patch cord

Connector type LC-LC

Table 9 2-port STM-1/4 MSC card cabling


17/40

A25000-A0800-E028-01-76P1


17

IDU Accessories Product Description FPH800 connection accessories

4 FPH800 connection accessoriesThis chapter provides an introduction and overview of the connectors and cables used

in FPH800 local connection. Most of the interfaces are located on the front panel. Only

the grounding point is on the lateral side of FPH800.

g For details on cables and connectors connecting ODU interfaces, refer to ODUmanuals.

Before the introduction of cables, SFP (small form-factor pluggable) modules is to be

introduced.

4.1 SFP transceiver

SFP interface

There are 2 SFP interfaces on the front panel of FPH800 which can be configured to

Ethrenet port or STM-1 port by software. SFP interface is designed to support SDH and

GE communication standards.

SFP transceiver

SFP transceiver, or SFP module, is a compact, hot-pluggable transceiver used for com-

munication applications. It is specified by a multi-source agreement (MSA). It interfaces

FPH800 mainboard to a fiber optic or copper networking cable.

SFP transceivers are available with a variety of types, allowing users to select the appro-

priate transceiver for each link to provide required electrical or optical reach over the

available cable types. This solution gives interface flexibility for FPH800.

g For all the types and order codes of SFP modules, refer toIDU and Accessories OrderCodes Reference.

4.1.1 SFP transceiver for electrical interfaces

Electrical SFP is compliant with 10BASE-T/100Base-TX/1000 Base-T interfaces. It does

not support synchronous Ethernet.

Figure 10 Electrical SFP module application

RJ45Connector

4PairsCable

Electrical SFP Module


18/40

18 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionFPH800 connection accessories

4.1.2 SFP transceiver for optical interfaces

Optical SFP is compliant with 1000 Base-X, synchronous Ethernet and STM-1 inter-

faces. Multi-mode fiber and single-mode fiber are supported through different types of

SFP optical transceivers.

Figure 11 Optical SFP module application

4.2 Cables and connectors for Ethernet copper interfaces

Figure 12 GE electrical interfaces

FE/GE electrical interfaces

The cables and connectors in this section are used to connect Ethernet copper inter-faces on the front panel, such as

4 X 10/100/1000 Base-T ports.

DCN port.

LC

Optical Patch-Cord

Optical SFP module

Item Description

Interface type 10/100/1000 Base-T

Duplex mode Half and full

Rate 10/100/1000 Mbit/s

Table 10 GE/FE electrical interfaces

RJ45 Shielded Connector

4 Pairs Shielded Cable

ElectricalSFP Module


19/40

A25000-A0800-E028-01-76P1


19


RJ45 connector

RJ45 is a registered jack standard for a modular connector using 8 conductors, which

specifies the physical male and female connectors as well as the pin assignments of the

wires in a cable. The physical dimensions of the connectors are specified in ANSI/TIA-

1096-A and ISO-8877 standards.

Cat6 cable

Category 6 cable, commonly referred to Cat6, is a cable standard for Gigabit Ethernet

and other network physical layers that is backward compatible with Cat5/5e and Cat3

cable standard. Compared with Cat5 and Cat5e, Cat6 features more stringent specifi-

cations for crosstalk and system noise. The cable standard provides performance of up

to 250 MHz and is suitable for 10BASE-T, 100BASE-TX (Fast Ethernet), 1000BASE-T/1000BASE-TX (Gigabit Ethernet) and 10GBASE-T (10-Gigabit Ethernet).

Table 11is the property of GE copper cable with length = 5m. And users can also make

Ethernet copper cords with cables and connectors with the given order codes in brakets

for other length.

MDI type auto sensing MDI/MDIX

Front panel reference 10/100/1000 Base-T, DCN

Connector type Shielded GE RJ45 eight-pin gold plated finishing

Cable 4 pairs STP cat6

Power Supply -48 Volt P + E functionality is supported in interfaces 3

and 4. A label (Pwr) indicates the presence of the ODU

power supply.

Property Description

Order code CS73199.05

Connector 1 RJ45 (T555ETRJ.08)

Connector 2 RJ45 (T555ETRJ.08)

Cable Ethernet STP Cat6 cable (T555ECR5.00)

Length 5 m

Table 11 Property of GE copper cable reel with length = 5 m

Connector 1 Pair Color Connector 2

1 pair A + white/orange 1

2 pair A - orange 2

Table 12 Wiring

Item Description

Table 10 GE/FE electrical interfaces (Cont.)


20/40

20 A25000-A0800-E028-01-76P1



4.3 Cables for Ethernet optical interfaces

Multimode/singlemode optical cables are used to connect FPH800 optical GE interfaceover SFP optical modules with local traffic. The application of optical fiber is seen in

Figure 11.

For description on SFP interface and SFP module, refer to Section SFP transceiver for

optical interfaces.

GE optical interface

Gigabit Ethernet (GE) has the speed to 1000 Mbit/s.

LC connector

LC (Lucent Connector) connector is the most common type of connector. It terminates

the end of an optical fiber, and enables quicker connection and disconnection than splic-

ing. The connectors mechanically couple and align the cores of fibers so that light can

pass.

MM optical fiber

Multi-mode (MM) optical fiber is a type of optical fiber mostly used for communication

over short distances. Typical MM links have data rates of 10 Mbit/s to 10 Gbit/s over link

lengths of up to 600 m (300 m for 10 Gbit/s).

g For all the types and order codes of MM fiber patch cords, refer toIDU and AccessoriesOrder Codes Reference.

3 pair B + white/green 3

4 pair C + blue 4

5 pair C - white/blue 5

6 pair B - green 6

7 pair D + white/brown 7

8 pair D - brown 8


Table 12 Wiring (Cont.)


Cable type break-out cable 2 X 2.0 mm LSZH

Connector LC-LC

Fiber type multi-mode 50/125 um

Fanout leg length 195 +/- 5 mm

Table 13 Properties for MM fiber patch cord


21/40

A25000-A0800-E028-01-76P1


21


SM optical fiber

Single-mode (SM) optical fiber is better at retaining the fidelity of each light pulse over

longer distances than MM fiber. SM fiber can have a higher bandwidth than MM fiber.

g For all the types and order codes of SM fiber patch cords, refer toIDU and AccessoriesOrder Codes Reference.

4.4 Cables for STM-1 optical interfaces

Single-mode optical cables are used to connect FPH800 optical STM-1 interface over

SFP optical modules with local traffic. The application of optical fiber is seen in Figure

11.

For description on SFP interface and SFP module, refer to Section SFP transceiver for

optical interfaces.

STM-1 interface

The STM-1 (Synchronous Transport Module level-1) is the SDH ITU-T fiber optic

network transmission standard. It has a rate of 155.52 Mbit/s.

g For all the types and order codes of SM fiber patch cords, refer toIDU and AccessoriesOrder Codes Reference.

Insertion loss maximum 0.50 dB @ 1300 nm

Operating temperature - 25 OC ~ + 70 OC

The insertion loss test acc. to IEC 61300-3-4


Table 13 Properties for MM fiber patch cord (Cont.)


Cable type break-out cable 2 X 2.0 mm, Riser

Connector LC-LC

Fiber type single-mode 9/125 um

Fanout leg length 300 -50/+ 10 mm

Insertion loss maximum 0.50 dB @ 1550 nm

Return loss minimum 46 dB @ 1550 nm

Operating temperature - 25 OC ~ + 70 OC

The insertion loss test acc. to IEC 61300-3-4

The return loss test acc. to IEC 61300-3-6

Table 14 Properties for SM fiber patch cord


22/40

22 A25000-A0800-E028-01-76P1



For properties of SM fiber patch cord, refer to SM optical fiber.

4.5 Cables for E1 interfaces

E1 interface

An E1 link operates over two separate sets of wires, usually twisted pair calbe. The line

data rate is 2.048 Mbit/s which is split into 32 timeslots each being allocated 8 bits in

turn.

The E1/T1 interfaces are used only as local interfaces. There are 16 X E1/T1 interfaces

with 75 ohm and 120 ohm impedance.

The following table descripes the pin definition of the E1/T1 interface.

Item Description

Interface Type E1/T1 short haul

Front panel reference 16 X E1/T1Interface rate E1/T1 Software selectable

Connector type MDR68 connector

Table 15 E1/T1 interfaces

Pin

number

Pin function Direction Pin

number

Pin function Direction

1 TXTIP1 output 35 RXTIP1 input

2 TXRING1 output 36 RXRING1 input















17 GND - 51 GND -

Table 16 Pinout


23/40

A25000-A0800-E028-01-76P1


23


Pin 17, 34, 51 and 68 are required to be connected to Ground. DC isolation is possible

as an external option by not connecting the cable shield to the connector shield. The

RING pin of transmit and receive need connect to GND through the external cable when

supporting the unbalanced 75 ohm coaxial cable.

Coaxial cable

Coaxial cable, or coax, has an inner conductor surrounded by a flexible, tubular insulat-

ing layer, surrounded by a tubular conducting shield.

Coaxial cable is used as a transmission line for radio frequency signals. One advantageof coax over other types of radio transmission line is that in an ideal coaxial cable the

electromagnetic field carrying the signal exists only in the space between the inner and

outer conductors. This allows coaxial cable runs to be installed next to metal objects

such as gutters without the power losses that occur in other types of transmission lines.

Coaxial cable also provides protection of the signal from external electromagnetic inter-

ference.

g For all the types and order codes of E1 cables, refer toIDU and Accessories OrderCodes Reference.

















34 GND - 68 GND -

Pin

number

Pin function Direction Pin

number

Pin function Direction

Table 16 Pinout (Cont.)


24/40

24 A25000-A0800-E028-01-76P1



4.5.1 75 ohm coaxial cable

Figure 13 75 ohm Coaxial Cable with MDR68 connectors

Construction

Conductor: 30 AWG solid bare copper wire

Insulation: Foam PE, diameter = 1.1 mm

Inner braiding: 0.08 mm bare copper wire, Min. 95% coverage

Inner jacket: LSZH, gray, diameter = 1.8 mm, identified with number

Outer braiding: 0.10 mm bare copper wire, Min. 40% coverage

Outer jacket: LSZH, black, diameter = 14.0 mm

Braid construction: E1 patch cord 75 ohm MDR68-MDR68 cable assembly 60 exit, 32

core coaxial cable

Electrical characteristics

Conductor DC resistance: < 365 ohm/Km at 20C

Impedance: 75 5 ohm at 1 MHz

Return loss: 3.3 dB/100 m at 1 MHz to 10 MHz

Attenuation: 3.3 dB/100 m at 1 MHz; 9.5 dB/100 m at 10 MHz

Assembly rating

Voltage rating: 30 V AC

Current rating: 0.5 A/Pin

Temperature rating: -40C to + 85C

Pin 1Pin 34

Pin 68 Pin 35

75ohm Coaxial Cable

MDR Plug Connector

MDR68 Shell

Termination Cable

Cable Joint

Pin 1

Pin 1Pin 35Pin 68

Pin 34

Pin 34

Pin 68Pin 35


25/40

A25000-A0800-E028-01-76P1


25


Insulation resistance: 100 M

Withstanding Voltage: 300 V AC

4.5.2 120 ohm coaxial cable

Figure 14 32 pair 120 ohm cable with MDR68 connectors

Construction

Conductor: Diameter 0.40 mm solid bare copper wire

Insulation: Foam PE, diameter = 0.82 mm

Drain Wire: 0.40 mm solid copper wire

Cabling: PET tape

AL/PET tape: Diameter 0.40 mm tined copper drain wire

Braiding: 0.12 mm bare copper wire, Min. 85% coverage

Jacket: LSZH, black, Max. diameter = 12.0 mm

Braid construction: E1 patch cord 120 ohm MDR68-MDR68 cable assembly 60 exit, 32

twisted pair shielded round cable


Characteristic impedance: 120 5 ohm at 1 MHz

Twisted pair: Max. -53.0 dB/100 m at 1 MHz

Attenuation: Max. 2.8 dB/100 m at 1 MHz

Assembly rating

Pin 1Pin 34

Pin 68 Pin 35

32pair Shielded RoundCable

MDR Metal Junction Shell

MDR Connector

Pin 68

Pin 68

Pin 35

Pin 34

Pin 34

Pin 35Pin 1

Pin 1


26/40

26 A25000-A0800-E028-01-76P1



Voltage rating: 30 V AC

Current rating: 0.5 A/Pin

Temperature rating: -40C ~+ 85C

Insulation resistance: 100 M

Withstanding Voltage: 300 V AC

4.6 Cables and connectors for FlexBus interfaces

Figure 15 FB cable applicationFB interface

The FlexBus (FB) interface is designed to support legacy product interface from Nokia.

The FB interface only operate in local interface mode. It only transfers data between two

indoor units.

TNC connector

The TNC (threaded Neill-Concelman) connector is a threaded version of the BNC con-

nector. The connector has a 50 ohm impedance (75 ohm is also available). It has better

performance than the BNC connector at microwave frequencies.

For description on coaxial cable, refer to Coaxial cable.

Users can assemble FB cable with the cable and connector with the order codes given

below. Note that the two TNC connectors are alternative.

Order code Item

T55256.02 FB cable reel, 500 m

T55255.07 IDU/ODU TNC connector, male

Table 17 FB cable and connector

FLEXBUS CABLE

T55256.02

FLEXBUS CABLE

T55256.02

TNC CONNECTOR (MALE)

T55255.07

TNC CONNECTOR (MALE ANGLE)

T55255.08


27/40

A25000-A0800-E028-01-76P1


27


The cable interface uses +5 V and +3.3 V power supply for operation. The consumption

of the cable interface alone is around 200 mA and 80 mA for +5 V and +3.3 V respec-

tively.

4.7 D.C Power interface

FPH800 provides protection of power supply interface. If one power supply failed,

FPH800 can switch to the other. A power cable is an assembly of two electrical conduc-

tors, held together with an overall sheath. This interface carries the -48 Volt DC power

supply.

Figure 16 Power supply interface

T55255.08 IDU/ODU TNC connector, male angle

Order code Item

Table 17 FB cable and connector (Cont.)

Phoenix 4-Pin Connector

2 X 1.5 mm cable

Plastic Hook

(Lower Enclosure)

Plastic Hook

(Upper Enclosure)


28/40

28 A25000-A0800-E028-01-76P1



g A 12 A fuse is used in power channel.

Construction

Conductor: Standard tinned copper wire

Construction: 30 / 0.25 mm

Insulation: HD-PE

Nominal thickness: 0.7 mm

Minimum thickness: 0.53 mm

Nominal diameter: 3.00 0.10 mm

Filler

Braiding: 0.12 mm tinned copper wire

Coverage: 85%

Jacket: LSZH

Color: Optional

Nominal thickness: 0.74 mm

Minimum thickness: 0.60 mm

Nominal diameter: 8.00 0.20 mm

Interface type Floating -48 Volt DC

Voltage range -40.5 VDC to -57.6 VDC

When operating without ODU power supply the

system shall be able to operate in the extended

voltage range -38.4 VDC to -57.6 VDC.

Reference Indoor Unit / Variant 1, with the following exceptions:

the input voltage is floating

Front panel reference PWR A and PWR B

Connector type Phoenix 4 Pin connector, 12A.

Fastening by screw required.

Connector shell 4-Pole straight strain snap

Antistatic plastic bag BAG ESD 80x120 pink, zip lock

Maximum current 10 A

Table 18 Power supply interfaces

Pin number Pin function

1 PWR A +

2 PWR B +

3 PWR B -

4 PWR A -

Table 19 Pinout


29/40

A25000-A0800-E028-01-76P1


29



Conductor DC resistance: 15 /Km

Insulation resistance: 100 M/Km

Dielectric strength: AC 2000 V/ 1Min

Machenical characteristics

Working temperature: -40C ~ +80C

Color code

4.8 Grounding cable

The grounding cable is 10 AWG UL cable which meets ROHS requirement.

Figure 17 Grouding cable assembly

Construction

Conductor: 104/ 0.254 mm stranded tinned copper wire

Nom diameter: 3.43 mm

Insulation: PVC

Color: Yellow/Green

Nom thickness: 0.76 mm

Min thickness: 0.69 mm

Diameter: 5.07 0.08 mm

Electrical characteristics Conductor DC resistance at 20C: 3.90 /Km

Sparkal test: 10000 V

Voltage rating: 600 V

Flame characteristics

Fire resistance: VW-1 and FT1, pass

Core Color Core Color

1 Black 2 Red

Table 20 Color code of power cable


30/40

30 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionFPH800 patch panels

5 FPH800 patch panelsThere are three types of patch panels applicable to FPH800, which are RJ45 patch

panel, CC4 patch panel, and BNC patch panel. The patch panels are the switching

equipments allowing the incoming signals from 16XE1/T1 interface MDR68 connector

to be output from 16XRJ45 connector, 32XCC4 connector or 32XBNC connector. If the

users equipment connecting to the FPH800 16XE1/T1 interface does not have the inlet

for MDR68 connector, one patch panel can be used to switch the signals to fit the con-

nector which can be carried by the equipment.

5.1 RJ45 patch panel

RJ45 patch panel is used to switch the signals input from MDR68 connector to be output

from 16XRJ45 connectors.

Figure 18 RJ45 patch panel

5.2 CC4 patch panel

CC4 patch panel is used to switch the signals input from MDR68 connector to be output

from 32XCC4 connectors.


Height 22 mm

Width 440.6 mm

Depth 69.976 mm

Operating temperature -5C ~ +55C

Table 21 RJ45 patch panel characteristics

Pin 1Pin 34

Pin 68 Pin 35Pin 1


31/40

A25000-A0800-E028-01-76P1


31

IDU Accessories Product Description FPH800 patch panels

Figure 19 CC4 patch panel

5.3 BNC patch panel

BNC patch panel is used to switch the signals input from MDR68 connector to be output

from 32XBNC connectors.

Figure 20 BNC patch panel


Height 22 mm

Width 440.6 mm

Depth 81 mm


Table 22 CC4 patch panel characteristics

Pin 1Pin 34

Pin 68 Pin 35

Out In


Height 44 mm

Width 440.6 mm

Depth 54.1 mm


Table 23 BNC patch panel characteristics

Pin 1Pin 34

Pin 68 Pin 35

Out

In


32/40

32 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionFPH800 USB key

6 FPH800 USB key

6.1 Physical information

g For the detailed codes and descriptions, please refer to FlexiPacket Hub 800 IDU Rel.2.5 Order Codes Reference manual.

The USB key is used for IDU/ODU configuration and software load backup. 1 GigaByte

Serial Data Flash memory is suitable for in-system reprogramming using Serial Periph-

eral Interface (SPI).

The USB key interface is not a real external interface because it does not enable any

interconnection of digital network components but it gives the external access of the

USB key unit that is a proper component of the equipment.

The USB key interface deals with a Serial Peripheral Interface (SPI) system that

consists of one master device and one slave device. Exactly, in the USB key interface,

the master is defined as the processor of the system controller unit providing the SPI

clock and the slave selection command. While the slave works as any non-volatile

memory device suitable for in-system reprogramming.

Figure 21 USB key connection

Mechanical demension and interface

Parameter ESD-rated enclosure

Length with cap 66.1 mm (2.602 in) MaxWidth 16.60 0.20 mm (0.654 0.008 in)

Height 7.02 0.20 mm (0.276 0.008 in)

Interface type/Front

panel reference

USB

Table 24 Mechanical dimension and interface

USB key


33/40

A25000-A0800-E028-01-76P1


33

IDU Accessories Product Description FPH800 USB key

6.2 Key characteristics

It is possible to insert the USB key under the powered appliance. And the replacement

key must not produce any temporary interruption of service. The insertion into the equip-ment connector is detected through the presence line toward the system controller with

the ground level.

The 3.3 V power source must be supplied to the interface throughout a protection fuse

to ensure the integrity of SPI. But it is needed to be aware of the environmental hazards

such as accidental short circuits possible at the interface, connector pins that are touch-

able throughout the front panel cut-out when the USB key is not inserted.

If the system controller need to RESET, the working USB key must be terminated and

the IDLE status should be set. After RESET condition is cleared, all the operation will be

resumed back to normal.

Performance

The Industrial Grade UFD is USB 2.0 high-speed (480 Mb/sec) and USB 1.1 full-speed

(12 Mb/sec) compliant.

LED functionality

The Industrial Grade UFD with standard enclosure incorporates a LED activity indicator

that functions as described below:

LED flashing: Industrial Grade UFD is transmitting/receiving data or is identification

process.

Default LED colors: Blue.

Environmental specifications

Appliance Connector type Notes

Device connector 8 contacts Double socket

straight through hole 2mmgrid

The connector is part of

USB key unit

Card connector 8 contacts right angle pin

header through hole 2mm

grid

Equipment access

Table 25 USB key connectors

Parameter Value

Sustained read up to 30 MB/sec

Sustained write up to 20 MB/sec

Table 26 Read/Write performance


34/40


35/40

A25000-A0800-E028-01-76P1


35

IDU Accessories Product Description Dual-IDU accessories

7 Dual-IDU accessories

7.1 Dual-IDU shroud

Figure 22 Dual-IDU shroud

Figure 23 Backplane of the shroud

FPH800 shroud is designed for dual-IDU site configuration. 2 IDUs can be plugged into

the shroud. 2 guide pins are added at the backplane of the shroud for easy plug and 2

guide holes are added on FPH800 rear side to match this backplane.

With the backplane of the shroud, 2 FPH800 can work in active/standby.

g For details on dual-IDU site configuration and FPH800 rear side interfaces, refer to IDUProduct description.

BACKPLANE GUIDE PIN

GND


Height 2 U

Width 450 mm

Depth 256 mm

Table 28 Shroud characteristics


36/40

36 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionDual-IDU accessories

7.2 Dual-IDU protection panel and optical splitter

7.2.1 Protection panel

Figure 24 A protection panel with 2 optic splitters

The protection panel is used for local traffic in dual-IDU mode. Its user interface is con-

nected with local equipment, while its 2 IDU interfaces connected with 2 IDUs respec-

tively. Only one of the IDUs is working in active mode. The other IDU is used for traffic

protection.

The application above applies to

8 pairs of GE electrical interface

2 pairs of GE optical interface

1 pair of 16 X E1/T1 interface

gFor details on dual-IDU site configuration, refer to IDU Product Description.

7.2.2 Optical splitter

Figure 25 Optic splitter

The optic splitter is a plug-in unit of the dual-IDU protection panel. It must be ordered

separately from the protection panel. One protection panel fits 2 optic splitters at most.

Pin 1Pin 34

Pin 68 Pin 35Pin 1

OPTIC SPLITTER


Height 1 U

Width 440 mm without brackets

Depth 150 mm

Table 29 Protection panel characteristics

OPTICAL INTERFACE


37/40

A25000-A0800-E028-01-76P1


37

IDU Accessories Product Description Dual-IDU accessories

When no optic splitter is installed, a blank panel should be installed in the place of the

splitter.

There are 2 kinds of optic splitters with the same look. One is for multi-mode (MM) fiber

connection and the other is for single-mode (SM) fiber connection. Users can tell fromthe label on the faceplate of the splitter.

7.3 Dual-IDU power injector

Power injector a 1-U-height box, which is used to support dual-IDU protection while 1 +

0 ODU is connected to the IDU. It realizes two funtions: one is to inject power for GE

port to ODU, another is to do GE splitter as the command from IDU via control port on

dual-IDU power injector. With this GE splitter function, GE impedence can be match and

the cable to ODU can be longer. The target is to reach 50 m.

IDU alarm interface is connected with dual-IDU Power injector port to control which IDU

is connected with ODU. These IDUs work in active/standby mode. In normal condition,ODU is connected with Master IDU via Power injector. If Master IDU is down, the Slave

one will be active and send out command to dual-IDU Power injector to switch. Dual-IDU

Power injector implements the switch as this command. In this case, one IDU failure will

not result in traffic down to ODU.

The supported GE interface number can be 4 for each dual-IDU Power injector, and 8

GE ports if cascaded dual-IDU Power injector is used.

A grounding connector is on the lateral side of the Power injector. It must be connected

to the grounding point on the rack.

Figure 26 Power injector

g Two dual-IDU Power Injectors support cascading for extensive ODU connection. The forthe connection application, please refer toIDU Product Descriptionmanual. In the cas-

cading connection, the cascaded cable is not provided by NSN. Please follow the pin

defination in Table 30to make the cascaded cable with GE cable and RJ45 connectors.

RJ-45 for Cascade

RJ-45 for Alarm from Dual-IDU

GE Electrical with Dual-IDU GE Electrical with ODUs

RJ-45 for External Alarm Power Connector


1 pair A + white/orange 1

2 pair A - orange 2

3 pair B + white/green 7

4 pair C + blue 4

5 pair C - white/blue 5

Table 30 Wiring


38/40

38 A25000-A0800-E028-01-76P1


IDU Accessories Product DescriptionDual-IDU accessories

6 pair B - green 6

7 pair D + white/brown 3

8 pair D - brown 8


Table 30 Wiring (Cont.)


39/40

A25000-A0800-E028-01-76P1


39

IDU Accessories Product Description FPH800 installation tools

8 FPH800 installation tools

g For the detailed codes, please refer to IDU and Accessories Order Codes Reference.For the detailed description, refer to IDU HW Install.

FPH800 mounting kits includes the following.

FPH800 dual-IDU shroud 21 mounting kit

Containing 21 mounting bracket for shroud, screws and nuts.

FPH800 mounting kit 21 rack

Containing Lshaped brackets for 21 rack, plastic bags, screws, washers, spring

washers and nuts.

FPH800 mounting kit 19 rack

Containing Lshaped brackets for 19 rack, plastic bags, screws, washers, spring

washers and nuts.

Power connector kit

Grounding kit

Containing grounding cable, plastic bags, screws, washers, spring washers and

nuts.

FlexiPacket IDU NEBS-compliant

Containing grounding cable dedicated for NEBS use. Its an alternative for the

grounding kit.

g For FOC installation information, refer to FOC manuals.


40/40

IDU Accessories Product DescriptionGlossary

9 Glossary

10 BASET (10BaseT)

IEEE 802.3 media standard abbreviation for a 10 Mbps baseband Ethernet usingtwisted pair cabling

100 BASET (100BaseT)

IEEE standard for high speed 100 Mbps Ethernet.

1000 BASET (1000BaseT)

IEEE standard 802.3ab for Gigabit Ethernet over an unshielded twisted-pair wire.

Asynchronous Transfer Mode (ATM)

Transfer mode in which the information is organised into cells. It is asynchronous in the

sense that the recurrence of cells containing information from an individual user is not

necessarily periodic.

Element Management System (EMS)

Part of the network management system that provides the management functions for a

set of network elements.

PPS&ToD

PPS: pulse per second.

ToD: time of day.

Synchronous Digital Hierarchy (SDH)

Standardized multiplexing protocols that support multiple transports over optical fiber.

Synchronous Optical Network (SONET)

Transfer mode standardised by ANSI that is a variation of the SDH international stan-

dard, designed to run on optical fiber.

Time-division Multiplexing (TDM)

Multiplexing technique in which two or more lower bandwidth communications channels

are combined into a higher bandwidth channel by allocating frequency time slots in turn

to each of the lower bandwidth communications.

Universal Asynchronous Receiver/Transmitter (UART)

A piece of computer hardware that translates data between parallel and serial forms.

UARTs are now commonly included in microcontrollers.

05 Idu Accessories Product Description

Documents

Transcript of 05 Idu Accessories Product Description