03-Chapter 3 Managing the User Account

8/20/2019 03-Chapter 3 Managing the User Account

http://slidepdf.com/reader/full/03-chapter-3-managing-the-user-account 1/7

Operation Manual – IPM VolumeUA5000 Universal Access Unit Table of Contents

Huawei Technologies Proprietary

i

Table of Contents

Chapter 3 Managing the User Account....................................................................................... 3-1

3.1 Introduction to the User Account ....................................................................................... 3-1

3.2 Managing a User Account ................................................................................................. 3-2

3.2.1 Adding a User Account ........................................................................................... 3-2

3.2.2 Querying the User Account Information.................................................................. 3-3

3.2.3 Modifying the Attributes of a User Account............................................................. 3-4

3.2.4 Deleting a User Account ......................................................................................... 3-6



Operation Manual – IPM VolumeUA5000 Universal Access Unit Chapter 3 Managing the User Account


3-1

Chapter 3 Managing the User Account

This chapter introduces the following:

Introduction to the User Account

Managing a User Account

3.1 Introduction to the User Account

In this manual, a user account refers to an account used by the maintenance staff to log

on to and manage the UA5000 through the CLI. System users are Common users,

Operators, Administrators and Superusers.

A Common user can query only the basic information of the system.

An Operator can configure the UA5000 and some services.

An Administrator can manage all the functions and services, and users of lower

levels.

A Superuser has the highest authority for managing all the functions and services,

apart from managing lower levels users. The Superuser cannot be created. By

default, the system has one superuser.

When a user attempts to log on, the UA5000 authenticates the user name and

password. It then assigns the user with the corresponding authority.

Table 3–1 lists the commands for managing a user.

Table 3–1 Managing a user account

To… Use… In…

Add/Delete a user [undo] terminal user name Privilege mode

Modify the user authority terminal user level Privilege mode

Modify the user password terminal user password Privilege mode

Modify the additionalinformation on a user

terminal user apdinfo Privilege mode

Modify the reentry times ofa user

terminal user reenter Privilege mode

Query the user information display terminal user Common user mode

Query the online userinformation

display client Common user mode





3-2

3.2 Managing a User Account

By default, there is a Superuser root with the password admin. After logging in to the

system, the user root can configure and manage other system users.

The user account management includes:

Adding a User

Querying the User

Modifying the Attributes of a User

Deleting a User

3.2.1 Adding a User Account

To add a user to the CLI, use the terminal user name command. You need to providethe information such as the account, password, reenter number, user level and addition

information.

Account

Also known as user name, it is unique in the UA5000 system. A user name

consists of 1 to 15 printable characters without any space in between.

Password (case sensitive)

The password consists of 1 to 15 characters. Common users and operators can

modify their only own passwords, while the Administrator and Superuser can

modify the passwords of all other users.

User level

There are three levels for users: Common User, Operator and Administrator.

Re-entry count

When a system user attempts to log on, the UA5000 checks whether someone

has logged on using the same account. If yes, the system will check the re-enter

number set for the user and decide whether to allow the user to log on. The

number ranges from 0 to 4. When the reentry time is set as 0, the user is not

allowed to log on, but the user still exists.

User additional information

The user additional information may include the contact method of a system user.

It can be as long as 30 characters.





3-3

Note:

The Superuser root cannot be deleted, but its password can be modified.

Multiple users can be added at a time. The CLI supports up to 126 system users.

Example

To add the user huawei with the reentry times as 2 and additional information as

0755-8001234567, do as follows:

huawei#terminal user name

User name (<=15 chars):huawei

User password(<=15 chars):

Confirm Password(<=15 chars):

User's Level(1--3)

1. Common User 2. Operator 3. Administrator:1

Permitted reenter number(0--4):2

User append information(<=30 chars):0755-8001234567

This user has been added

Repeat this operation? (y/n)[n]:n

Now query its information using the display terminal user command.

huawei#display terminal user

{ all<K>|online<K>|name<K> }:all

-----------------------------------------------------

Name Level Status ReenterNum AppendInfo

-------------------------------------------------------

root Super Online 1 none

huawei User Offline 2 0755-8001234567

-------------------------------------------------------

Total record(s) number: 2

3.2.2 Querying the User Account Information

I. Querying the registration information about a user

To query the user information such as user name, user level, online state, reentry times,

use the display terminal user command.

Example

To query the information on the user huawei, do as follows:

huawei#display terminal user

{ all<K>|online<K>|name<K> }:name





3-4

{ username<S><1,15> }:huawei

-------------------------------------------------------

Name Level Status ReenterNum AppendInfo

-------------------------------------------------------

huawei User omline 2 0755-8001234567

-------------------------------------------------------------------------------------

Note:

The display terminal user command will show the information on system users at

your user level or lower.

II. Querying the online users information

To query the information on online users, use the display client command. The

information covers the client ID, client name, client type and IP address (for Telnet

terminals only).

huawei#display client

--------------------------------------------------------------------------

ID Client name Domain name IP Address Login Time

--------------------------------------------------------------------------

1 huawei -- 10.11.51.66 2005-06-27 09:34:24

2 root -- Serial 2005-06-27 09:56:11

--------------------------------------------------------------------------

3.2.3 Modifying the Attributes of a User Account

The Superuser or Administrator can modify the attributes of a common user or an

operator, including the user level, password, re-entry times and extra information.

I. Modifying the user level

To modify the authority of a user, use the terminal user level command.

Example

To modify the user huawei as an operator, do as follows:

huawei#terminal user level


1. Common User 2. Operator 3. Administrator:





3-5

User's Level(1--3)2

Confirm Level: 2

Information will take effect when this user logs on next time


II. Modifying the user password

To modify the user password, use the terminal user password command.

Example

To modify the password of user huawei, do as follows:

huawei#terminal user password


New password(<=15 chars):

Confirm Password(<=15 chars):

Information takes effect



III. Modifying the re-entry times

To modify the re-entry times, use the terminal user reenter command.

Example

To modify the re-entry times of huawei, do as follows:

huawei#terminal user reenter


Permitted reenter number(0--4):3

Confirm Reenter Number(0--4):3



IV. Modifying the details of a user

To modify the additional information on a user, use the terminal user apdinfo

command.

Example

To modify the additional information on huawei, do as follows:

huawei#terminal user apdinfo


User append information(<=30 chars):[email protected]

Information takes effect






3-6

3.2.4 Deleting a User Account

To delete a user, the Superuser or Administrator can use the undo terminal user

name command.

Note:

You cannot delete the Superuser root.

You cannot delete an online user. To delete an online Telnet user, first use the

telnet delete command to disconnect the user. (A user of a higher level can force a

low level online Telnet user to go offline using the telnet delete command.)

Example

To delete user huawei, do as follows:

huawei#undo terminal user name


Are you sure to delete the user?(y/n) [n]: y

This user has been deleted

03-Chapter 3 Managing the User Account

Documents

Transcript of 03-Chapter 3 Managing the User Account