© Copyright zExperts Ltd 2012 Disk Storage (E)CKD VS SAN A presentation for SMUG June 2012 Frank...

© Copyright zExperts Ltd 2012

Disk Storage(E)CKD VS SAN

A presentation for SMUG

June 2012

Frank McDaid

zExperts Ltd

[email protected]

© Copyright zExperts 2012

Introduction Up until now, the only Operating System running

on most z platforms has been z/OS (MVS). z/OS can only use CKD Disks. With the current strategy of running z/VM hosting

Linux on the z platform, there is now the option to use either CKD DASD or SAN SCSI.

The aim of this presentation is to compare the pros and cons of using CKD DASD and SAN attached disks in order to make an informed decision on the most suitable strategy going forward.


IBM disks, a brief history IBM designed the disk data architecture called Count Key

Data (CKD) back in the 1960's Very different disk format to the Fixed Block Architecture

(FBA) which is more familiar to people working on UNIX, Linux, and MS

Windows

Modern mainframe disks from IBM, HDS, and others are all based on concepts introduced in StorageTek’s Iceberg project.

The Iceberg Project populated a cabinet full of FBA SCSI disks, and then put a controller in front of them that emulates CKD to the mainframe.

Up to this point, a CKD DASD was just one (quite large) disk platter.


Storagetek’s Iceberg A revolutionary Disk for the mainframe market

Four years in development project cost $145 million commercially available from 1992 onwards not commercially successful until IBM agreed to resell them as an IBM

RAMAC Virtual Array (RVA) First mainframe disk to use RAID

Originally Redundant Arrays of Inexpensive Disks Renamed to Redundant Arrays of Independent Disks

Iceberg linked together a series of cheap disks By spreading data over several smaller disks and adding parity data

Iceberg protected the information it stored from loss and corruption. Also allowed for use of dynamic rebuild to recover from a disk failure

• undetectable by the end user of that data• failed components could be “hot swapped” and repopulated with no downtime


IBM’s FBA Devices IBM had introduced real FBA devices for the mainframe

much earlier than 1992 the 3310 and the 3370

Greatly disliked by the system programming community who were used to CKD

mostly because of the granularity of addressing all the blocks on the disk

IBM responded to the Mainframe Systems Programmers’ moans and groans about FBA by ….

…. discontinuing FBA format disks for the mainframe

FBA was the future, but IBM’s customers (primarily the MVS or z/OS community) wanted CKD


CKD devices today CKD disks are not sold nowadays

just FBA devices with controllers that do CKD emulation

CKD “looking” disks are 'created' by smart storage controllers essentially virtualised by microcode out of FBA disk arrays

The Iceberg project led the way on that changed the way MF storage has been designed ever since

Everything since 3330 uses smart storage controllers that create "virtual" CKD devices out of real FBA ones

This emulation does have an effect on price MF storage is more expensive than most of the straight FBA/SAN/NAS type

solutions available today

z/VM and z/OS (MVS) don't know they are not talking to 3390's for the most part.


Disk Architecture - CKD Each physical disk record consists of a count field, an

optional key field, and a ("user") data field with error correction/detection information appended to each field, which is separated by gaps

Recorded space is larger than required because of the gap separation

The principle behind the architecture is that since data record lengths can vary, they all have an associated count field which indicates the size of the key, if used, and the size of the data

The count field has the identification of the physical location in cylinder-head-record format, the length of the key, and the length of the data

The key may be omitted or consist of a string of characters. Most often the key is omitted


Disk Architecture - ECKD ECKD refers to the CCW (Channel Command Words)

commands used with cached controllers for IBM DASD The new commands were introduced on the cached versions

of the IBM 3880 controller and were extended on the 3390 The ECKD channel commands provide improved performance

for all protocols the obsolete Bus & Tag interface ESCON (Enterprise Systems Connection) interface FICON (Fibre Connectivity) protocol

ECKD allows the programmer to provide the control unit with information on intent and to perform operations in a single channel program that would require multiple channel programs with CKD


Parallel Access Volumes (PAV) On the subject of improved performance, it’s worth mentioning

Parallel Access Volumes (PAVs) This gives a performance improvement to the z platform by

allowing a system access to Disk volumes in parallel Accomplished by defining a ‘base address’ representing the real

disk volume and aliases associated with that base address aliases can be either static or dynamic

With PAV, a real DASD volume is accessed through a base subchannel and one or more alias subchannels

HyperPAV support complements the existing basic PAV support potentially reducing the number of alias-device addresses needed for

parallel I/O operations since HyperPAVs are dynamically bound to a base device for each I/O operation instead of being bound statically like basic PAVs.


FBA In IBM's implementation, Fixed Block Architecture (FBA) is a

disk drive that stores data in blocks of fixed size Blocks are addressed by block number relative to the

beginning of the file Various block sizes (512, 1024, 2048 & 4096) were featured on IBM’s

FBA devices The term FBA is not often used since the introduction of SCSI

devices which use a scheme called LBA (Logical Block Addressing)

LBA is a linear addressing scheme; blocks are located by an integer index, with the first block being LBA 0, the second LBA 1, and so on

In SANs where logical drives (LUNs) are composed via LUN virtualization and aggregation, LBA addressing of individual disk is translated by a software layer to provide uniform LBA addressing for the entire storage device


z/VM & Linux Disks z/VM was doing storage virtualization long before storage

virtualization became popular using 'minidisks' This is a real CKD device such as a 3390 subdivided into many

smaller virtual disks not the same thing as disk slices, nothing is written to a partition table on

the disk To create a mini-disk means updating the z/VM directory

the place that defines all the attributes for all the virtual machines that will be running on that computer

There you enter the start and end cylinder of each mini-disk You have to be sure that your new mini-disk does not overlay any other mini-

disks When one is working with numbers like 1113, the maths is pretty easy.

Minidisk 1 starts at cylinder 2 and ends at cylinder 10. Minidisk 2 starts at cylinder 11 and ends...

the trick is not to end up defining overlapping minidisks


FCP – SAN attached SAN disks can be attached to System z via FCP

z/OS can not use this SAN storage as it’s restricted to (E)CKD format disk z/VM can see them, but it can not fully utilize them unless an emulation

layer is configured (EDEV) Linux guests running under z/VM can fully utilise these disks as if they

were running on any other platform

It is possible and not unusual to have a hybrid storage architecture with a combination of CKD disks and SAN disks

If z/VM and/or Linux do use SAN disks (e.g. for low cost), then they are NOT utilising System z’s huge I/O subsystem

With 256+ I/O channels, multipath devices, etc, the z Platform is a powerful box for doing I/O

It can be contested that this is not really an issue as benchmarking of CKD vs.SAN has shown that with a correctly configured FCP and multipath architecture under Linux, the SAN devices can out-perform FICON attached CKD devices.


NAS This “low cost” storage is accessed by UNIX, Linux

or Windows on non-z platforms using TCP/IP based protocols: NFS, ISCSI or CIFS.

The z Platform with an OSA (Open Systems Adapter) installed provides Ethernet connections.

The OSA sits where a channel adapter used to, and provides a number of industry standard Ethernet connections so that the z Platform is no longer isolated from the "Network is the Computer" world.

With z/VM and Linux on the z platform, native TCP/IP requirements are met and with NFS this cheaper storage can be utilised.


FICON/ECKD Characteristics 1:1 mapping host subchannel:dasd Serialization of I/Os per subchannel I/O request queue in Linux Disk blocks are 4KB High availability by FICON path groups Load balancing by FICON path groups Parallel Access Volumes


FCP/SCSI Characteristics Several I/Os can be issued against a LUN immediately Queuing in the FICON Express card and/or in the

storage server Additional I/O request queue in Linux Disk blocks are 512 bytes High availability by Linux multipathing, type failover Load balancing by Linux multipathing, type multibus


(E)CKD v SAN Under zVM/zLinux

z/VM and Linux on System z can use either architecture, CKD or FCP/SAN

This next section lists the advantages and disadvantages to using either architecture when configuring z/VM and Linux.


Pros of (E)CKD over SAN (1/2) Easy manageability using the existing traditional

z/VM tools (backup, cloning, flashcopy, etc.) or z/OS tools such as DFDSS

ECKD disk storage types are well supported under z/VM and are well integrated into the tooling that is supplied with z/VM

Multipathing Multiple connections between the storage unit and the

host, or multipathing, is supported without any problems or concerns and is particularly effective for FICON and FICON Express systems


Pros of (E)CKD over SAN (2/2) Unified DR

With z/VM sharing the z Platform with z/OS, putting Linux systems on disk technology that z/OS understands means that both can be part of a GDPS DR configuration

Hardware reuse – The DASD usually already on the floor Accessibility of storage for multiple IBM operating systems

z/OS and z/VM understand CKD. If demand for disk is greater or lesser in a particular environment, the CKD disk can be assigned wherever it is needed without worries of compatibility

Channel-attached infrastructure To backup z/VM using native tools there would have to be a tape drive

attached to z/VM. Sharing the same DASD with z/OS means that z/OS can perform backups of z/VM DASD thus alleviating the need to setup a z/VM tape infrastructure.

Excellent performance instrumentation and reporting.


Cons of (E)CKD over SAN Limited size - CKD volumes are much smaller than most SAN

volumes LVM and MD RAID technologies allow creating larger logical

volumes Extra expense for the CKD interfaces on storage servers

On most of the CKD storage devices, the necessary interfaces to plug in to FICON are anywhere between 400% and 500% of the cost of a FCP interface. This skews the cost-per-megabyte for CKD disk dramatically

"It's different." If you're trying to convince people to move applications from other

environments where they can request enormous LUNs and not have to worry about LVM or MD, it's one more thing to have to convince them to do, and the argument generates a fair amount of unnecessary resistance.

There is limited z/VM and Linux support for DS8000 EAV volumes.


Pros of SAN over (E)CKD (1/2) Very large volumes without LVM

SAN disks can be of pretty much arbitrary size. It's not unusual to have single volumes reaching 500GB each in the SAN environment.

Lower cost infrastructure The necessary mainframe adapters are the same price as FICON

adapters, they are the same adapter with different microcode, but all the other interfaces that these adapters connect to: SAN switches, interfaces to the storage devices, etc, are identical to the ones used for open systems. These are usually much cheaper than the CKD interfaces, often 400%-500% cheaper

Volume format compatibility with open systems volumes inside the storage units

TSM understands backing up FCP / SAN attached storage on the open systems connected to the SAN. This allows other systems to mount volumes created by Linux under z/VM, if some form of locking software is available on both systems.


Pros of SAN over (E)CKD (2/2) Re-use of existing open system resources

If there is extra capacity in the SAN then attaching the mainframe allows it to use some the over-provisioned space. Since z/VM itself can also reside on FCP / SAN-only disk, there may be benefits without additional disk investment.

Common storage management policies and procedures with open systems

Allocation of a FCP / SAN disk can be done in the same way as it is done for open systems

When attached to the z Platform, the overhead of converting from block to ECKD and back to block oriented in the CU (Control Unit)

More I/Os can be executed in parallel, although ECKD volumes using Parallel Access Volumes (PAVs) can minimise this advantage

More data can be moved in a single I/O command


Cons of SAN over (E)CKD (1/3) Mainframe communication

Very few mainframe tools understand it. Most cloning and copy facilities are not available with SAN disk, and z/VM cannot invoke some specialised features of certain disk units

mostly for old political battle reasons inside and outside IBM, but the problem remains

Configuration complexity Without familiarity of the z Platform, for z/VM and Storage

administrators it may appear complex to configure. LUNs and WWPNs are not native or natural concepts to people who normally work with z/VM or z/OS.

Dump tools Most z/OS and z/VM volume dump tools cannot access FCP storage at all.

When z/VM is using SCSI volumes for its own use, the SAN devices emulate (EDEV) 9336 disks (and thus can be dumped with DDR), but pure FCP / SAN volumes are not accessible to CMS-based tools (CMS is z/VM’s equivalent to a linux Shell)


Cons of SAN over (E)CKD (2/3) Recovery in DR requires additional planning

probably won’t get all the applications and data in the same restore cycle; a separate data restoration plan is necessary

No native support for FCP SAN-attached tape in VM At least one channel-attached drive is required. alternative is to

buy a commercial solution to backup both z/VM and linux data which will involve a cost or write an in-house solution

Performance differences SAN attached disk using EDEV to emulate an FBA device to z/VM

has a measurable performance overhead when used for z/VM CP functions.

Multiple physical paths Managing multiple physical paths to FCP/SAN disk is still a bit

difficult for non-Linux systems, including z/VM.


Cons of SAN over (E)CKD (3/3) z/OS and FCP devices

z/OS doesn't understand FCP/SAN devices at all z/VM and Linux are perfectly happy to run on FCP/SAN

or emulated 9336 (EDEV) on FCP, but z/OS has to have (E)CKD

Until z/VM adds (E)CKD emulation on FCP/SAN disk, you have to have separate disks for z/OS

Linux native (or running under z/VM) supports SAN attached tape.


(E)CKD vs. SAN – Other considerations

Backup / Recovery Management / provisioning Disaster Recovery Data Administration


Backup and recovery The next few charts form a comparison of z/VM &

Linux backup and recovery options


z/VM and Linux on CKD z/VM disks

z/VM data can be backed up using DFDSS from z/OS without tapes assigned to z/VM as long as the z/VM disks are accessible

With tapes assign to z/VM a number of z/VM backup methodologies can be used but there could be a software cost involved

Linux Disks Linux disks can be backed up by Tivoli Storage manager

(TSM) Linux disks can be backed up by DFDSS or a z/VM

backup method but the restoration of data is not granular


z/VM and Linux on SAN z/VM disks

z/VM data can NOT be backed up using DFDSS Most z/OS and z/VM volume dump tools cannot access FCP

storage z/VM disk (not Linux) using EDEV (FBA emulation) can be

dumped using tools like DDR if a channel attached tape drive is available to z/VM

Linux Disks Linux disks can be backed up by Tivoli Storage manager (TSM) Linux disks can NOT be backed up by DFDSS FCP / SAN volumes are not accessible to CMS-based tools (CMS

is z/VM’s equivalent to a Linux Shell).


Management and Provisioning ECKD - Steps to Add Devices to Linux on System z

1. Setup hardware and make all physical connections2. Add ECKD I/O definitions to z/VM via IOCP deck3. Create z/VM directory entries with assigned disk dedicated to the

virtual machine4. Logon on to new virtual machine user5. Install Linux on System z in new Linux guest virtual machine6. Add additional disk to Linux on System z virtual machine via

directory entry or CP attach command7. Bring Linux on System z devices online8. Format Linux on System z DASD devices using dasdfmt9. Partition devices using fdasd10. Add to LVM or create a filesystem directly on the partitioned

device


Management and Provisioning SAN - Steps to Add FCP Devices to Linux on System z

1. Setup hardware and make all physical connections between the DISK array, System z, and SAN switch

2. Setup zoning on the switch to the System z channel3. On the Disk array define, map and mask FBA LUNs4. Add I/O definitions to z/VM using IOCDS5. NPIV enable the channels on the HMC6. Create z/VM directory entries with disk in the User Direct file7. Install Linux on System z in newly allocated Linux guest virtual machine8. Add additional disk to the Linux on System z virtual machine via directory

entry or CP attach command 1. Vary devices online2. Associate WWPN with device address3. Associate LUN(s) with WWPN

9. Partition the Linux device, /dev/………10. Add the Linux device(/dev/…..) to LVM and/or create filesystem


Disaster Recovery Scenario GDPS xDR Solution

Sites typically run a ‘Freeze and Go’ GDPS DR policy. So, there isn’t any Active / Active option using GDPS on

the z/Platform. If z/VM were aligned with the z/OS GDPS policy, then

there may be applications which are candidates for migrating to Linux under z/VM, but who are running Active /Active clusters, for instance.

To give these applications the same availability, different architectural options would need to be considered


xDR Pros and Cons Advantages

z/OS currently has GDPS DR architecture in placeDR procedures tried and tested

Disadvantages Requires z/VM and Linux to exclusively use CKD DASD

Active / Active architectures not supported with current GDPS ‘Freeze and Go’ policy


Other Clustering DR solutions When porting applications from other platforms to

Linux under z/VM, consideration must be given to the DR and failover architectures that are in place for that application.

For the most part, these DR and Failover solutions can be replicated on the z/Platform but maybe not with the same software

Any solution would need to be evaluated on an Application by Application basis.


Other Clustering DR solutions Advantages

Provides application with same SLA Application architecture retained

Disadvantages Greater planning involved It may be the case that all applications may not be restored in the

same restore cycle and a separate data restoration plan is necessary for particular applications

May compromise any current GDPS xDR solution New software / hardware may be required to architect the same

solution as when the application was running on a non-z platform


Data Administration The administration of LUN based data versus CKD

based data will be different At most installations, this should not be an issue as

there are Storage personnel who are highly experienced in both disciplines

The area of Storage administration that needs to be addressed is the lack of knowledge of native z/VM based data

Training is required, but this is the case regardless of whether z/VM data is hosted on CKD or SAN disks.


Conclusions 1/3 Benchmarks performed on z/VM Linux systems to compare the

various configuration options have shown that using native SAN disks under Linux gives better performance than CKD. The performance improvement over CKD is minimal and would not make it the ultimate deciding factor on using SAN over CKD.

Despite z/VM on the z/Platform having huge I/O capabilities inherent in the z architecture, with the correct number of FCP channels and multipathing configured under Linux, the SAN can match and out-perform CKD attached Storage.

Using SAN storage for native z/VM utilising EDEV (Emulated devices) gives good performance results, on a par with native SAN and CKD, but there is a price to pay with increased CPU. The increase is not insignificant but should not be a blocker to using only SAN storage for both z/VM and Linux.


Conclusions 2/3 If z/VM is going to be in a SSI configuration (z/VM

clustering) or part of a GDPS xDR architecture, at least one CKD disk must be available to z/VM Linux.

Apart from performance, the other considerations (covered previously) are (a) Backup / Recovery, (b) Management / Provisioning, (c) DR and (d) Data Administration.

If the decision is made to use SAN storage then there could be a cost outlay for extra FICON/FCP cards and channels to connect the z/Platform up to an available SAN.


Conclusions 3/3 There’s a place for both types of storage. A good

approach maybe to allocate z/VM specific disks on CKD and store application data on the type of disk that provides the best cost/performance trade off. Applications that benefit from very large volumes (like databases) would be good candidates for FCP/SAN storage.

© Copyright zExperts Ltd 2012 Disk Storage (E)CKD VS SAN A presentation for SMUG June 2012 Frank...

Documents

Transcript of © Copyright zExperts Ltd 2012 Disk Storage (E)CKD VS SAN A presentation for SMUG June 2012 Frank...