Post on 02-Jun-2018
8/10/2019 ZTE Narrow Band Data Configuration
1/20
8/10/2019 ZTE Narrow Band Data Configuration
2/20
2
Objectives:
1. master narrow band data configuration
2. Master H.248 protocol
8/10/2019 ZTE Narrow Band Data Configuration
3/20
3
Delete original data
The rack maybe have some original data, so we need to delete them .allsystem data is backup on floder E: \DATA\V0100 and V0101.
1. telnet 129.0.52.51 8888 (129.0.52.51 is the outband IP address)
2. passwordzxmg
3. change the data attribute into read and write r06_attr E:/DATA/V0100/*.* -R
r06_attr E:/DATA/V0101/*.* -R
4. delete data: r06_del E:/DATA/V0100/*.*
r06_del E:/DATA/V0101/*.*
r06_del D:/durable
r06_del D:/persist
5. comfirm all data is empty. ftp 129.0.52.51
user name and password are root CD E:\DATA\V0100
LS
CD E:\DATA\V0101
LS
Then all data should be empty.
ftp://ftp%20129.0.52.51/ftp://ftp%20129.0.52.51/ftp://ftp%20129.0.52.51/ftp://ftp%20129.0.52.51/8/10/2019 ZTE Narrow Band Data Configuration
4/20
4
Contents:
Lab equipment allocation
Data preparation
Data configuration
Check MSAG running status
8/10/2019 ZTE Narrow Band Data Configuration
5/20
5
Lab equipment allocation
SUN server :168.2.16.1
129.0.22.1
26NIC
10.66.22.1
28NIC SSNI
COL-
ACT-
STA-
1 2 34 5 6 7 8 9101112
HS1 HS2 OK1 OK2 PSCONSOLE
COL-
ACT-
STA-
1 2 3 4 5 6 7 8 9101112
HS1 HS2 OK1 OK2 PSCONSOLE
129.0.100.1
10.76.100.1
129.0.100.5
10.76.100.5
1 5200 port
of backboard
10.76.52.51
7 5200 port of
backboard
10.76.52.57
1 5200 port of
front board
129.0.52.51
7 5200 port
of front board
129.0.52.57
GW:10.66.25
4.254
GW
10.76.254.253
8/10/2019 ZTE Narrow Band Data Configuration
6/20
6
Data configure interface
interface function notes Switch
SHELL debugging Only two
command can
be supported:
routeShow and
sysReboot
exit
MSAG# Can use
show
command
Config switch to MSAG(config)#
Ag switch to MSAG(ag)#
MSAG(config-a
g)#
Or
MSAG(ag)#
Hardware
and
narrowban
d data
configurati
on
Exit switch to MSAG#
MSAG(config)# Board band
data
configurati
on
Ag switch to MSAG(config-ag)#;
Epon switch to PON configuration interface
.
Logout to exit the configuration
end exit to MSAG#;
8/10/2019 ZTE Narrow Band Data Configuration
7/207
Contents:
Lab equipment allocation
Data preparation
Data configuration
Check MSAG running status
8/10/2019 ZTE Narrow Band Data Configuration
8/208
Data preparation
SS typeZXSS10 or other SS;
SS IP address
MSAG IP address and mask
MSAG next hop
The VLAN of Uplink exchange port (tagged or untagged and
VLANID)
Protocol type (H.248) and port (2944)
Terminal ID and RTP resources
8/10/2019 ZTE Narrow Band Data Configuration
9/209
Data configuration
Enter 1123 port
8/10/2019 ZTE Narrow Band Data Configuration
10/2010
Configure physical location
Add rack
MSAG(ag)# add-rack rack 1 type 1
Add shelf
MSAG(ag)# add-shelf rack 1 physhf 0 type 6 Configure control board (Add main shelfs ICS)
MSAG(ag)# add-board-mics slot 9 type 1
8/10/2019 ZTE Narrow Band Data Configuration
11/2011
Configure physical location
Configure MGC
MSAG(ag)# add-mgc mgcid 1 mgctype 1 mgcip 10.61.252.100 mgcport2944
MSAG (ag)# mod-call subpriority 2
Configure media, control and management IP address
Plan 1: 5200 only have one IP address.media, control and managementIP is the same IP address
Plan 25200 configure 2 IP address, control and media IP address is thesame ip address, and management IP address is the other IP address.
Plan 3:5200 configure 2 IP address, media IP address uses one IP
address, but control and management IP address is different IP address. Plan 4:5200 configure 3 IP address respectively.
Plan 5: 5200 configure one management IP address. It have not narrowband functions.
8/10/2019 ZTE Narrow Band Data Configuration
12/2012
Plan 1: one IP
1. configure media IP
MSAG(ag)# add-voip-interface type 1 ipaddr 10.61.252.55
submask 255.255.252.0
2. configure media gateway
MSAG(ag)# add-voip-route nexthop 10.61.252.254
MSAG(config)# vlan add 120
MSAG(config)# vlan add-port 120 port 0/9/0 untagged
MSAG(config)# vlan voipmed add 120
3. configure protocol and ports
MSAG(ag)# add-mg mgport 2944 mgcid1 1
8/10/2019 ZTE Narrow Band Data Configuration
13/2013
Uplink interface enable
MSAG(config)# port enable 0/9/0
Add AG protocol capability
MSAG(ag)# add-mgcapabili faxpri1 faxpri2
8/10/2019 ZTE Narrow Band Data Configuration
14/2014
Configure subscriber resources
Add ALC
MSAG(ag)# add-board-slc slot 3 type 26
Add TERMINATION ID
Type one: zte SS type
MSAG(ag)# add-slctermid rack 1 shelf 0 beginslot 3 beginindex 0
num 32 tmidfix USER type 1
Type two: huawei ss type
MSAG(ag)# add-slctermid rack 1 shelf 0 beginslot 3 beginindex 0num 32 tmidfix A type 2 begno 0
Type three: length is fixed and configurable.
MSAG(ag)# add-slctermid rack 1 shelf 0 beginslot 3 beginindex 0num 32 tmidfix USER type 3 digitlen 4 begno 0
Configure VOIP resources
MSAG(ag)# add-board-mpr slot 11
MSAG(ag)# add-board-mprb slot 12
8/10/2019 ZTE Narrow Band Data Configuration
15/2015
Add VOIP TERMINATION ID
Type 1:
MSAG(ag)# add-ipstermid slot 11 subcard 1 tmidfix RTP
Type 2:
MSAG(ag)# add-ipstermid slot 11 subcard 1 tmidfix RTP type
2 begno 0
Type 3:
MSAG(ag)# add-ipstermid slot 11 subcard 1 tmidfix RTP type
3 digitlen 3 begno 0
8/10/2019 ZTE Narrow Band Data Configuration
16/2016
Add media route configuration
MSAG(ag)# add-mednat mprslot 11 mprsubcard 1 nicslot 9
inphyport 5 exphyport 5 exipaddr 10.61.252.201 udpport 6000
MSAG(ag)# add-mednat mprslot 11 mprsubcard 2 nicslot 9
inphyport 5 exphyport 5 exipaddr 10.61.252.201 udpport 8000
the IP address is media IP address.
The minmam value of UDPPORT is 6000. every subcard needs 2000 ports.
8/10/2019 ZTE Narrow Band Data Configuration
17/2017
Configure jiter of MPRB
MSAG(ag)#mod-rtppar-mprb parid 1 mindelay 20 maxdelay 120
nomdelay 20
SAVE DATA
MSAG(config)# save
8/10/2019 ZTE Narrow Band Data Configuration
18/2018
Contents:
Lab equipment allocation
Data preparation
Data configuration
Check MSAG running status
8/10/2019 ZTE Narrow Band Data Configuration
19/2019
telnet 129.0.52.1 8888 password: zxmg
1. 0x1389>pe
Cards on Slot 9,11 and 12 are active.
The last row has 0x1309 item, which means NIC is normal.
2. 0x1389>unit 1
3. 0x1389>h248s link OK means H248 link OK.
4. r07_vershow
Check different card version.
5. cpu
6. cpuclear 7. ppreset
8. changeover querystate
8/10/2019 ZTE Narrow Band Data Configuration
20/20
univ.zte.com.cn