WOOD STAIN - INTERIORSOLVENT BASED DYE SOLUTION

Staining ismerelyameansof adding color towood. Stainingmaybeused todarken the

wood, to bring out a grain pattern, tomakeone variety ofwood look like another or to

accentdetailsorfixturesofapieceoffurniture.SheenlacWoodstainsareTransparenttype

consistofDyesandsolventandrecommendforInteriorwoodwork.

INSPIRING CREATIVITY

FEATURES & BENEFITS:

TECHNICAL DATA

Ÿ 14vibrantwoodtonesavailableforInteriors.

Ÿ AllareInter-mixableandcreatenewdesiredtoneasperone'staste.

Ÿ Solvent-basedwood stainswon't raise the grain on thewood, so youwon't need toworry about sanding the

finish.

SuitableforWoodfurniture,cabinets,doors,windows,wallpaneling,trimbutitisnotrecommendedforexposedExteriors.

RECOMMENDED USE

Appearance–Lowviscouscoloredliquid.

Color–Availablein4differenttones.

Odour–Characteristicalcoholtype.

Solubility–Immisciblewithwater.

Finish–Notapplicable.

Gloss level (60° head)–Notapplicable.

Flash Point –above12°C

Spreading rate – Thepractical spreading ratewillvary depending on the porosity and profile of thesubstrate,aswellastheapplicationtechniqueandtoolsused.

Shelf Life –36monthsfromthedateofproductionin unopened condition and, stored at therecommendedstoragecondition.

Storage & Packing

Tobestoredinacool,dry&wellventilatedplaceawayfrommoisture,heatanddirectsunlight.

Packaging

1 L500ml100ml 3 L 5 L 10 L 20 L

Surface Preparation: Allwood surfacesmust be clean, firm

anddry.Removeanyoil,grease,mortardroppings,etc.

NEW WOOD:Sandinthedirectionofthegrain,toasmooth

finishwith150followedby220gritpaper.Removedustwitha

dampcloth.

PREVIOUSLY VARNISHED WOOD IN GOOD

CONDITION:Sandtoobtainasmoothsurfaceusing150grit

emerypaper.Removeallsandingdustusingavacuumorcloth

dampenedwithmineralspirits.

PREVIOUSLY VARNISHED WOOD IN POOR

CONDITION: Strip completely by deep sanding or by using

Sheenlac Paint Remover. Rinse thoroughly with clean water.

Deepsandtountilthereisnoevidenceofanyresidue.Remove

dustwithadampcloth.

WOOD PREVIOUSLY COATED WITH WAX

SEALER/OIL BASED WOOD PRESERVATIVE:

Mechanically sand until there is no evidence of residue.

Removedustwithadampcloth.

PREVIOUSLY PAINTED WOOD: Strip old paint by deep

sandingorbyusingSheenlacPaintRemover.Rinsethoroughly

withcleanwater.Sandbarewoodtoasmoothfinish.Remove

dustwithadampcloth.

STAIN ON THE BARE WOOD – Adding stain to bare or

stripped wood can both change the color and highlight the

grainpatternofanyinteriorwoodbutthisisanoptional.Apply

Sheenlac SBWood stains by rubbing or brushing against the

directionofthegrainwillhelpfilldeepporeswithstain.Apply

aliberalamountofstain,givingthewoodanampleamountto

absorb.Allowtodryfor30-60mins.

STAIN ON SEALER – A thin coat of NC sanding sealer on

barewoodwillactasawoodconditionerandthiswillenhance

theuniformspreadingofstain.SpraySheenlacwoodstainover

theconditionedwoodtillthedesiredcolordepthreached.

HEALTH & SAFETY INSTRUCTIONS:Ÿ Alwayskeeppaintoutofreachofchildren.

Ÿ Ensuregoodventilationduringapplicationanddrying.

Ÿ If accidental contact with skin should occur, washimmediatelywithsoapandwater.

Ÿ Take care to avoid contact with the eyes. In case ofcontact,immediatelyrinsetheeyeswithplentyofwater

Ÿ andseekmedicalattention.

Ÿ Harmful if swallowed.Seekmedicalattentionanddonotinducevomiting.

Ÿ Donotsmokewhilepainting.

Ÿ Flammable.Storeinacooldryplaceawayfromheatandsparks.

Ÿ Refer to Material Safety Data Sheet for completeinformation.

APPLICATION DETAILS

DryingTime

(@30°C&60R/H)

Allowatleast60minsbeforestarting

anextcoat.

ApplicationEnvironment

SurfaceTemperature

AmbientTemperature

RelativeHumidity

Min

Max

20°C

30°C

20°C

35°C

20%

85%

INSPIRING CREATIVITY

DISCLAIMER: The recommendations contained herein are given in all good faith and are meant to guide the specifier or the user. They are based on results gained from our tests and experiences and are believed to be reliable. No guarantee is implied by the recommendations contained herein since conditions of use, method of application and cleanliness of the substrate prior to painting are beyond our control. As application, environmental and design factors can vary, due care should be exercised in the selection and verification of the performance and use of the coatingN.B: Technology may change with time necessitating changes to this Technical Data Sheet (TDS). It is the responsibility of the user to ensure that the latest TDS is being usedVer.1.0/TDS/2017

Regd. Office: Sheenlac Paints Ltd.OldNo.109B,NewNo.124,DevelopedPlots,SIDCOIndustrialEstate,Ambattur,Chennai-600098.

Forproductrelatedqueries,feedbackandqualitycomplaints,pleasecontact:Customercare:+918300030404Email:ccc@sheenlac.in,Web:www.sheenlac.in

Application Method:

Staining dramatically and permanently changes the wood'sappearance,soalwaystestastainbeforeapplyingonanareaofthepiecethatwon'tshow--suchasthebottomorbackofafurniture.Becauseeachstainproducesadistinctivelookondifferent typesofwood, it's crucial touse a scrap from thesamewoodasthefurniture ismade. If thetest-piece looksblotchywhenyouapplystain,thenfirstapplyaliberalcoatofSheenlacLacquersandingsealerasawoodconditionerabout15minutesbeforestaining.

Applymorestainifyouwishtodarkenthewoodfurther.Asitdries, the stained finish may take on a dull look. A freshappearance will return when finish is applied later. Do notsand the stained surface as this will lead to patch anddifferentcolordepth.

Clean up: Cloths and soiled ragsmay self-ignitewithoutwarning. Wash out well in warm soapy water beforedisposal.Remove as much product as possible from applicationequipmentpriortocleaning.