WOOD STAIN - INTERIORsheenlac.com/wp-content/uploads/2018/09/Wood-Stain... · 2019-10-25 · a...
Transcript of WOOD STAIN - INTERIORsheenlac.com/wp-content/uploads/2018/09/Wood-Stain... · 2019-10-25 · a...
WOOD STAIN - INTERIORSOLVENT BASED DYE SOLUTION
Staining ismerelyameansof adding color towood. Stainingmaybeused todarken the
wood, to bring out a grain pattern, tomakeone variety ofwood look like another or to
accentdetailsorfixturesofapieceoffurniture.SheenlacWoodstainsareTransparenttype
consistofDyesandsolventandrecommendforInteriorwoodwork.
INSPIRING CREATIVITY
FEATURES & BENEFITS:
TECHNICAL DATA
Ÿ 14vibrantwoodtonesavailableforInteriors.
Ÿ AllareInter-mixableandcreatenewdesiredtoneasperone'staste.
Ÿ Solvent-basedwood stainswon't raise the grain on thewood, so youwon't need toworry about sanding the
finish.
SuitableforWoodfurniture,cabinets,doors,windows,wallpaneling,trimbutitisnotrecommendedforexposedExteriors.
RECOMMENDED USE
Appearance–Lowviscouscoloredliquid.
Color–Availablein4differenttones.
Odour–Characteristicalcoholtype.
Solubility–Immisciblewithwater.
Finish–Notapplicable.
Gloss level (60° head)–Notapplicable.
Flash Point –above12°C
Spreading rate – Thepractical spreading ratewillvary depending on the porosity and profile of thesubstrate,aswellastheapplicationtechniqueandtoolsused.
Shelf Life –36monthsfromthedateofproductionin unopened condition and, stored at therecommendedstoragecondition.
Storage & Packing
Tobestoredinacool,dry&wellventilatedplaceawayfrommoisture,heatanddirectsunlight.
Packaging
1 L500ml100ml 3 L 5 L 10 L 20 L
Surface Preparation: Allwood surfacesmust be clean, firm
anddry.Removeanyoil,grease,mortardroppings,etc.
NEW WOOD:Sandinthedirectionofthegrain,toasmooth
finishwith150followedby220gritpaper.Removedustwitha
dampcloth.
PREVIOUSLY VARNISHED WOOD IN GOOD
CONDITION:Sandtoobtainasmoothsurfaceusing150grit
emerypaper.Removeallsandingdustusingavacuumorcloth
dampenedwithmineralspirits.
PREVIOUSLY VARNISHED WOOD IN POOR
CONDITION: Strip completely by deep sanding or by using
Sheenlac Paint Remover. Rinse thoroughly with clean water.
Deepsandtountilthereisnoevidenceofanyresidue.Remove
dustwithadampcloth.
WOOD PREVIOUSLY COATED WITH WAX
SEALER/OIL BASED WOOD PRESERVATIVE:
Mechanically sand until there is no evidence of residue.
Removedustwithadampcloth.
PREVIOUSLY PAINTED WOOD: Strip old paint by deep
sandingorbyusingSheenlacPaintRemover.Rinsethoroughly
withcleanwater.Sandbarewoodtoasmoothfinish.Remove
dustwithadampcloth.
STAIN ON THE BARE WOOD – Adding stain to bare or
stripped wood can both change the color and highlight the
grainpatternofanyinteriorwoodbutthisisanoptional.Apply
Sheenlac SBWood stains by rubbing or brushing against the
directionofthegrainwillhelpfilldeepporeswithstain.Apply
aliberalamountofstain,givingthewoodanampleamountto
absorb.Allowtodryfor30-60mins.
STAIN ON SEALER – A thin coat of NC sanding sealer on
barewoodwillactasawoodconditionerandthiswillenhance
theuniformspreadingofstain.SpraySheenlacwoodstainover
theconditionedwoodtillthedesiredcolordepthreached.
HEALTH & SAFETY INSTRUCTIONS:Ÿ Alwayskeeppaintoutofreachofchildren.
Ÿ Ensuregoodventilationduringapplicationanddrying.
Ÿ If accidental contact with skin should occur, washimmediatelywithsoapandwater.
Ÿ Take care to avoid contact with the eyes. In case ofcontact,immediatelyrinsetheeyeswithplentyofwater
Ÿ andseekmedicalattention.
Ÿ Harmful if swallowed.Seekmedicalattentionanddonotinducevomiting.
Ÿ Donotsmokewhilepainting.
Ÿ Flammable.Storeinacooldryplaceawayfromheatandsparks.
Ÿ Refer to Material Safety Data Sheet for completeinformation.
APPLICATION DETAILS
DryingTime
(@30°C&60R/H)
Allowatleast60minsbeforestarting
anextcoat.
ApplicationEnvironment
SurfaceTemperature
AmbientTemperature
RelativeHumidity
Min
Max
20°C
30°C
20°C
35°C
20%
85%
INSPIRING CREATIVITY
DISCLAIMER: The recommendations contained herein are given in all good faith and are meant to guide the specifier or the user. They are based on results gained from our tests and experiences and are believed to be reliable. No guarantee is implied by the recommendations contained herein since conditions of use, method of application and cleanliness of the substrate prior to painting are beyond our control. As application, environmental and design factors can vary, due care should be exercised in the selection and verification of the performance and use of the coatingN.B: Technology may change with time necessitating changes to this Technical Data Sheet (TDS). It is the responsibility of the user to ensure that the latest TDS is being usedVer.1.0/TDS/2017
Regd. Office: Sheenlac Paints Ltd.OldNo.109B,NewNo.124,DevelopedPlots,SIDCOIndustrialEstate,Ambattur,Chennai-600098.
Forproductrelatedqueries,feedbackandqualitycomplaints,pleasecontact:Customercare:+918300030404Email:[email protected],Web:www.sheenlac.in
Application Method:
Staining dramatically and permanently changes the wood'sappearance,soalwaystestastainbeforeapplyingonanareaofthepiecethatwon'tshow--suchasthebottomorbackofafurniture.Becauseeachstainproducesadistinctivelookondifferent typesofwood, it's crucial touse a scrap from thesamewoodasthefurniture ismade. If thetest-piece looksblotchywhenyouapplystain,thenfirstapplyaliberalcoatofSheenlacLacquersandingsealerasawoodconditionerabout15minutesbeforestaining.
Applymorestainifyouwishtodarkenthewoodfurther.Asitdries, the stained finish may take on a dull look. A freshappearance will return when finish is applied later. Do notsand the stained surface as this will lead to patch anddifferentcolordepth.
Clean up: Cloths and soiled ragsmay self-ignitewithoutwarning. Wash out well in warm soapy water beforedisposal.Remove as much product as possible from applicationequipmentpriortocleaning.