Post on 26-Sep-2018
WIDE
CIRULATION DOCUMENT DESPATCH ADVICE TECHNICAL COMMITTEE: LITD 07 Ref: Date 28-09-2015
LITD 07/T-43,102,106,
137,144,149,169,179-180
--------------------------------------------------------
ADDRESSED TO:
1. All Members of Audio, video and multimedia Sectional Committee, LITD 07
2. All Principal Members of Electronics and Information Technology Division Council (LITDC)
3 All Members of all the Panels of LITD 07 Sectional Committee
4 All others interested
Dear Sir(s),
Please find enclosed the following Draft Indian Standards in Wide Circulation in Annex.
Kindly examine these draft standards and forward your views stating any difficulties which you are likely to
experience in your business or profession, if this is finally adopted as a National Standards.
Last Date for comments : 29-11-2015
Comments, if any, may please made in the format indicated and mailed to the undersigned at the address given
below.
In case no comments are received or comments received are of editorial nature, you may kindly permit us to presume
your approval for the above document as finalized. However, in case of comments of technical in nature are received
then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional
committee for further necessary action if so desired by the Chairman, Sectional Committee.
This document is identical with corresponding IEC Standard and is not attached with this letter. For considering
comments on the document corresponding IEC Standard may be referred. In case of soft copy of IEC standard is
required, a request may be sent by mail.
Thanking you Yours faithfully,
(Narendra Singh)
Head (Electronics & IT) E-mail: hlitd@bis.org.in
litd@bis.org.in
Encl: As above Tele Fax: 23237093
mailto:litd@bis.org.in
ANNEX
Sl No. Doc. No. Title
1 DOC:LITD 07 ((3596)
/IEC 60118-1 (1995) + amd 1998)
Hearing aids Part 1: Hearing aids with induction
pick-up coil input (First Revision of IS 10776(Part 2): 1984)
2 DOC:LITD 07 (3597)
/IEC 60318-5 : 2006
Reference coupler for the measurement of hearing aids
using earphones coupled to the ear by means of ear
insert
(First Revision of IS 10781: 1984)
3 DOC:LITD 07 (3598)
/IEC 611142-2 (1996) Methods of measurement on receiving antennas
for satellite broadcast transmission in the 11/12
GHz band
Part 2:Mechanical and environmental tests on
individual and collective receiving antennas (First Revision IS 13987(Part 2): 1994)
4 DOC:LITD 07 (3599)
/IEC 60728-10 (2014)
Cable networks for television signals, sound
signals and interactive services
Part 10 System performance for return paths (First Revision lS 14231 (Part 8): 2002)
5 DOC:LITD 07 (3600)
/IEC 60942( 2003)
Electroacoustics - Sound Calibrators (First Revision
IS 15059:2001)
6 DOC:LITD 07 (3601) /Amd 1 IEC 60958-4( 2003)
Amd No. 1 to lS/IEC 60958 (Part 4): 2003 Digital
audio interface Part 4 professional applications (TA4)
7 DOC:LITD 07 (3602) /IEC62623: 2012
Desktop and notebook computers Measurement of energy consumption
8 DOC:LITD 07 (3603) /IEC61260-1 (2014)
lS 6964: 2001 Electrocoustics Octave-band and fractional- octaveband filters
(Second Revision lS 6964: 2001)
9 DOC:LITD 07 (3604)
/IEC62638-1 : 2014
Audio/video information and communication
technology equipment Part 1 : Safety requirements
: 07 07/-43,102,106, 28-09-2015 137,144,149,169,179-180
-------------------------------------------------------- : 1) , 07 2) 3) 4) () : , ,
28-11-2015
,
, ,
( )
( ) : : : hlitd@bis.org.in
mailto:hlitd@bis.org.in
1 DOC:LITD 07 ((3596)
/IEC60118-1 (1995) + and
1998)
- 2: - ( 10776 ( 2) : 1984 )
2 DOC:LITD 07 (3597)
/IEC60318-5 : 2006
- ( 10781 : 1984 )
3 DOC:LITD 07 (3598)
/IEC611142-2 (1996)
2 ( 13987 2: 1994 )
4 DOC:LITD 07 (3599)
/IEC 60728-10 (2014)
, 10 ( 14231 8: 2002 )
5 DOC:LITD 07 (3600)
/IEC 60942( 2003)
- ( 15059 : 2001 )
6 DOC:LITD 07 (3601)
/Amd 1 IEC 60958-4(
2003)
. 1 / 60958 4: 2003 4 (4)
7 DOC:LITD 07 (3602)
/IEC62623: 2012
8 DOC:LITD 07 (3603)
/IEC61260-1 (2014)
- - ( 6964: 2001 )
9 DOC:LITD 07 (3604)
/IEC62638-1 : 2014
/ 1 :
Doc No.: LITD 7 (3596)
IS 10776(Part 2) : .........
IEC 60118-1 : 1995
- 2: - ( )
Indian Standard
HEARING AIDS
PART 2: HEARING AIDS WITH INDUCTION PICK-UP COIL INPUT
(First Revision)
ICS 17.140.50
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
............2015 Price Group
Audio, Video and Multimedia systems and Equipment Sectional Committee, LITD 07 NATIONAL FOREWORD
This Indian Standard which is identical with IEC 60118-1:1995 Hearing aids Part 1: Hearing aids with induction pick-up coil input issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the Audio, Video
and Multimedia systems and Equipment Sectional Committee, LITD 07 and approval of the
Electronics and Information Technology Division Council.
This standard was first published in 1984 and was identical to IEC 60118-1 : 1983. This revision
is being published to align it with the latest version of IEC 60118-1 : 1995. Amendment 1(1998)
issued in the year 1998 to the above International standard has been incorporated in this standard.
The text of IEC Standard has been approved as suitable for publication as an Indian Standard
without deviations. Certain terminology and conventions are, however, not identical to those used
in Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standard also exist. The corresponding Indian Standard which is to be substituted in its respective
place is listed below along with its degree of equivalence for the edition indicated:
The technical committee has reviewed the provisions of the following International Standard
referred in this adopted standard and has decided that it is acceptable for use in conjunction with
this standard. For updated references, the latest edition of the referenced document applies,
including any corrigenda and amendment.
International Standards Title
IEC 60711:1981
Occluded-ear simulator for the measurement of earphones coupled to the ear by ear inserts
Only the English language text has been retained while adopting it in this Indian Standard and as
such the page numbers given here are not the same as in the IEC publication.
International Standards Corresponding Indian Standard Degree of
Equivalence
IEC 60118-0:1983, Hearing aids Part 0: Measurement of electroacoustical
characteristics Amendment 1 (1994)
IS 10776(Part 1):1984 Methods of
measurement of electro-acoustical
characteristics of hearing aids: Part 1
General measurements for air-conduction
hearing aids
(Superseding IS 3641:1976)
Technical
Equivalent
For the purpose of deciding whether a particular requirement of this standard is complied with,
the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded
off in accordance with IS 2 : 1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the
specified value in this standard.
Doc No.: LITD 7 (3597)
IS 10781 :........
IEC 60318-5 : 2006
( )
Indian Standard
ELECTROACOUSTICS SIMULATORS OF HUMAN HEAD AND EAR PART 5: 2 cm
3 coupler for the measurement of hearing aids and
earphones coupled to the ear by means of ear inserts
(First Revision)
ICS 17.140.50
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
............2015 Price Group
Audio, Video and Multimedia systems and Equipment Sectional Committee, LITD 07 NATIONAL FOREWORD
This Indian Standard which is identical with IEC 60318-5:2006 Electroacoustics Simulators of human head and ear Part 5 : 2 cm3 coupler for the measurement of hearing aids and earphones coupled to the ear by means of ear inserts issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the
Audio, Video and Multimedia systems and Equipment Sectional Committee, LITD 07 and
approval of the Electronics and Information Technology Division Council.
This standard was first published in 1984 and was identical to IEC 60126 : 1973. The IEC 60126
was further replaced by IEC 60318-5. This revision is being published to align it with the latest
version of IEC 60318-5 : 2006.
The text of IEC Standard has been approved as suitable for publication as an Indian Standard
without deviations. Certain terminology and conventions are, however, not identical to those used
in Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standard also exist. The corresponding Indian Standard which is to be substituted in its respective
place is listed below along with its degree of equivalence for the edition indicated:
The technical committee has reviewed the provisions of the following International Standards
referred in this adopted standard and has decided that they are acceptable for use in conjunction
with this standard. For updated references, the latest edition of the referenced document applies,
including any corrigenda and amendment.
International Standards Title
IEC 61094-4
Measurement microphones Part 4: Specifications for working standard microphones
BIPM/IEC/ISO/IUPAC/IUPAP/OIML:1995,
Guide to the expression of uncertainty in measurement (GUM)
International Standards Corresponding Indian Standard Degree of
Equivalence
ISO 389-2 Acoustics Reference zero for the calibration of audiometric
equipment Part 2: Reference equivalent threshold sound pressure
levels for pure tones and insert
earphones
IS 4755:1987 Reference zero for the
calibration of pure tone air conduction
audiometers
(first revision)
Technical
Equivalent
Only the English language text has been retained while adopting it in this Indian Standard and as
such the page numbers given here are not the same as in the IEC publication.
For the purpose of deciding whether a particular requirement of this standard is complied with,
the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded
off in accordance with IS 2 : 1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the
specified value in this standard.
Doc No.: LITD 7 (3598)
IS 13987(Part 2) :.........
IEC 61114-2 : 1996
2 ( )
Indian Standard
METHODS OF MEASUREMENT ON RECEIVING
ANTENNAS FOR SATELLITE BROADCAST TRANSMISSION IN THE 11/12 GHZ BAND
PART 2:Mechanical and environmental tests on individual and
collective receiving antennas (First Revision)
ICS 33.120.40
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
............2015 Price Group
Audio, Video and Multimedia systems and Equipment Sectional Committee, LITD 07 NATIONAL FOREWORD
This Indian Standard which is identical with IEC 61114-2 :1996 Methods of measurement on receiving antennas for satellite broadcast transmission in the 11/12 GHz band Part 2 :
Mechanical and environmental tests on individual and collective receiving antennas issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian
Standards on the recommendation of the Audio, Video and Multimedia systems and
Equipment Sectional Committee, LITD 07 and approval of the Electronics and Information
Technology Division Council.
This standard (Part 2) is one of the parts of a series of standards on Methods of measurement on receiving antennas for satellite broadcast transmission in the 11/12 GHz band. The other part in this series is:
Part 1 Electrical measurements
This standard was first published in 1995 and assistance has been derived from IEC
Document 12 A ( Sectt ) 332 while preparing this standard. This revision is being published
in order to align it with the latest version of IEC 61114-2 : 1996.
The text of IEC Standard has been approved as suitable for publication as an Indian Standard
without deviations. Certain terminology and conventions are, however, not identical to those
used in Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standard also exist. The corresponding Indian Standard which is to be substituted in its
respective place is listed below along with its degree of equivalence for the edition indicated:
The technical committee has reviewed the provisions of the following International Standards
referred in this adopted standard and has decided that they are acceptable for use in
conjunction with this standard. For updated references, the latest edition of the referenced
document applies, including any corrigenda and amendment.
International Standards Corresponding Indian Standard Degree of
Equivalence
IEC 61114-1: 1992, Methods of
measurement on receiving antennas for
satellite broadcast transmissions in the
12 GHz band Part 1: Electrical measurements on DBS receiving
antennas
IS 13987(Part 1):2012 Receiving
antennas for satellite broadcast
transmission in the 11/12 GHz band
Part 1 Electrical measurements
(first revision)
Identical
International Standards Title
IEV 50(712): 1992 International Electrotechnical Vocabulary (lEV) Chapter 712: Antennas
IEC 68-1: 1988, chloride solution)
Environmental testing Pa rt 1: General and guidance
IEC 68-2-11: 1981, Environmental testing Part 2: Tests Test Ka: Salt mist IEC 68-2-14: 1984 , Environmental testing Part 2: Tests Test N: Change of
temperature
IEC 68-2-52: 1984, Environmental testing Part 2: Tests Test Kb: Salt mist, cyclic (sodium
Only the English language text has been retained while adopting it in this Indian Standard and
as such the page numbers given here are not the same as in the IEC publication.
For the purpose of deciding whether a particular requirement of this standard is complied
with, the final value, observed or calculated, expressing the result of a test or analysis, shall be
rounded off in accordance with IS 2 : 1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.
Doc No.: LITD 7 (3599)
IS 14231 (Part 8) : ........
IEC 60728-10 : 2014
, 10
( )
Indian Standard
CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS
AND INTERACTIVE SERVICES
PART 10 SYSTEM PERFORMANCE FOR RETURN PATHS
(First Revision)
ICS 33.060.40
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
............2015 Price Group
Audio, Video and Multimedia systems and Equipment Sectional Committee, LITD 07 NATIONAL FOREWORD
This Indian Standard which is identical with IEC 60728-10 : 2014 Cable networks for television signals, sound signals and interactive services Part 10: System performance for return paths issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of
Indian Standards on the recommendation of the Audio, Video and Multimedia systems and
Equipment Sectional Committee, LITD 07 and approval of the Electronics and Information
Technology Division Council.
This standard (Part 8) is one of the parts of a series of standards on Cable networks for television signals, sound signals and interactive services. The other part of this series are:
Part 1 Safety requirements
Part 3 Active coaxial wideband distribution components
Part 4 Passive Coaxial Wideband Distribution Components
Part 5 Headend
Part 7 Electromagnetic Compatibility of Systems
Part 9 Interfaces of Cabled Distribution Systems for Digitally Modulated Signals
Part 10 Optical Equipment
This standard was first published in 2002 and was identical to IEC 60728-10 : 2001. This revision
is being published to align it with the latest version of IEC 60728-10 : 2014.
The text of IEC Standard has been approved as suitable for publication as an Indian Standard
without deviations. Certain terminology and conventions are, however, not identical to those used
in Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standards also exist. The corresponding Indian Standards, which are to be substituted in their
respective places, are listed below along with their degree of equivalence for the editions
indicated:
International Standards Corresponding Indian Standard Degree of
Equivalence
IEC 61000-4-2:1995, Electromagnetic
compatibility (EMC) Part 4: Testing and measurement techniques Section 2: Electrostatic discharge immunity
test. Basic EMC Publication
IS 14700(Part 4/Sec 2):2008
Electromagnetic compatibility (EMC)
Part 4: Testing and measurement
techniques Section 2: Electrostatic
discharge immunity test
(first revision)
Identical
The technical committee has reviewed the provisions of the following International Standards referred
in this adopted standard and has decided that they are acceptable for use in conjunction with this
standard. For updated references, the latest edition of the referenced document applies, including any
corrigenda and amendment.
International Standards Title
IEC 61094-1:2000, Measurement microphones Part 1: Specifications for laboratory standard microphones
IEC 61094-2:1992, Measurement microphones Part 2: Primary method for pressure calibration of laboratory standard microphones by the reciprocity technique
IEC 61094-4:1995, Measurement microphones Part 4: Specifications for working standard microphones
IEC 61094-5:2001, Measurement microphones Part 5: Methods for pressure calibration of working standard microphones by comparison
ISO 266:1997, Acoustics Preferred frequencies ISO/IEC Guide :1995, Guide to the expression of uncertainty in measurement ISO Publication:1993, ISBN 92-67-01075-1
International vocabulary of basic and general terms in metrology
OIML International Recommendation R 97:1990
Barometers
IEC 61000-4-3:2002, Electromagnetic
compatibility (EMC) Part 4-3: Testing and measurement techniques Radiated,radio-frequency,
electromagnetic field immunity test.
Basic EMC Publication
IS 14700(Part 4/Sec 3):2008
Electromagnetic compatibility (EMC)
Part 4: Testing & measurement
techniques Sec 3 Radiated, radio
frequency, electromagnetic field
immunity test (First Revision)
Identical
IEC 61000-6-1:1997, Electromagnetic
compatibility (EMC) Part 6: Generic standards Section 1: Immunity for residential, commercial and light-
industrial environments
IS 14700(Part 6/Sec 1):2008
Electromagnetic compatibility (EMC)-
Part 6 Generic standards Sec 1
Immunity for residential, commercial
and light-industrial environments
Identical
IEC 61672-1:2002, Electroacoustics Sound level meters Part 1: Specifications
IS 15575(Part 1):2000
Electroacoustics - Sound level meters -
Part 1: Specifications
(Superseding IS 9779:1981)
Identical
CISPR 22:1997, Information
technology equipment Radio disturbance characteristics Limits and methods of measurement
IS 6873(Part 7):2012
Limits and methods of measurements
of Radio disturbance characteristics
Part 7 Information technology
equipment (first revision)
Identical
CISPR/IEC 61000-6-3:1996,
Electromagnetic compatibility (EMC)
Part 6: Generic standards Section 3: Emission standard for residential,
commercial and light-industrial
environments
IS 14700(Part 6/Sec 3):2002
Electromagnetic compatibility (EMC)
Part 6: Generic standards Section 3:
Emission standards for residential,
commercial and light industrial
environment
Identical
Only the English language text has been retained while adopting it in this Indian Standard and as
such the page numbers given here are not the same as in the IEC publication.
For the purpose of deciding whether a particular requirement of this standard is complied with,
the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded
off in accordance with IS 2 : 1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the
specified value in this standard.
Doc No.: LITD 7 (3600)
IS 15059 : ..........
IEC 60942 : 2003
- ( )
Indian Standard
ELECTROACOUSTICS SOUND CALIBRATORS
(First Revision)
ICS 17.140.50
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
............2015 Price Group
Audio, Video and Multimedia systems and Equipment Sectional Committee, LITD 07 NATIONAL FOREWORD
This Indian Standard which is identical with IEC 60942 : 2003 Electroacoustics Sound calibrators issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the Audio, Video and Multimedia systems
and Equipment Sectional Committee, LITD 07 and approval of the Electronics and Information
Technology Division Council.
This standard was first published in 2001 and was identical to IEC 60942 : 1997. This revision is
being published to align it with the latest version of IEC 60942 : 2003.
The text of IEC Standard has been approved as suitable for publication as an Indian Standard
without deviations. Certain terminology and conventions are, however, not identical to those used
in Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard.
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standards also exist. The corresponding Indian Standards, which are to be substituted in their
respective places, are listed below along with their degree of equivalence for the editions indicated:
International Standard Corresponding Indian Standard Degree of
Equivalence
IEC 61000-4-2:1995,
Electromagnetic compatibility
(EMC) Part 4: Testing and measurement techniques Section 2: Electrostatic discharge immunity
test. Basic EMC Publication
IS 14700(Part 4/Sec 2):2008
Electromagnetic compatibility
(EMC) Part 4: Testing and
measurement techniques Section 2:
Electrostatic discharge immunity test
(First Revision)
Identical
IEC 61000-4-3:2002,
Electromagnetic compatibility
(EMC) Part 4-3: Testing and measurement techniques Radiated,radio-frequency,
electromagnetic field immunity test.
Basic EMC Publication
IS 14700(Part 4/Sec 3):2008
Electromagnetic compatibility
(EMC) Part 4: Testing &
measurement techniques Sec 3
Radiated, radio frequency,
electromagnetic field immunity test
(First Revision)
Identical
IEC 61000-6-1:1997,
Electromagnetic compatibility
(EMC) Part 6: Generic standards Section 1: Immunity for residential,
commercial and light-industrial
environments
IS 14700(Part 6/Sec 1):2008
Electromagnetic compatibility
(EMC)-Part 6 Generic standards Sec
1 Immunity for residential,
commercial and light-industrial
environments
Identical
The technical committee has reviewed the provisions of the following International Standards
referred in this adopted standard and has decided that they are acceptable for use in conjunction
with this standard. For updated references, the latest edition of the referenced document applies,
including any corrigenda and amendment.
International Standards Title
IEC 61094-1:2000, Measurement microphones Part 1: Specifications for laboratory standard microphones
IEC 61094-2:1992, Measurement microphones Part 2: Primary method for pressure calibration of laboratory standard microphones by the reciprocity technique
IEC 61094-4:1995, Measurement microphones Part 4: Specifications for working standard microphones
IEC 61094-5:2001, Measurement microphones Part 5: Methods for pressure calibration of working standard microphones by comparison
ISO 266:1997, Acoustics Preferred frequencies ISO/IEC Guide :1995, Guide to the expression of uncertainty in measurement ISO Publication:1993,
ISBN 92-67-01075-1, International vocabulary of basic and general terms in metrology
OIML International Recommendation R 97:1990,
Barometers
Only the English language text has been retained while adopting it in this Indian Standard and as
such the page numbers given here are not the same as in the IEC publication.
For the purpose of deciding whether a particular requirement of this standard is complied with, the
final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off
in accordance with IS 2 : 1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified
value in this standard.
IEC 61672-1:2002, Electroacoustics
Sound level meters Part 1: Specifications
IS 15575(Part 1):2000
Electroacoustics - Sound level meters
- Part 1: Specifications (Superseding
IS 9779:1981)
Identical
CISPR 22:1997, Information
technology equipment Radio disturbance characteristics Limits and methods of measurement
IS 6873(Part 7):2012
Limits and methods of measurements
of Radio disturbance characteristics
Part 7 Information technology
equipment [first revision]
Identical
CISPR/IEC 61000-6-3:1996,
Electromagnetic compatibility
(EMC) Part 6: Generic standards Section 3: Emission standard for
residential, commercial and light-
industrial environments
IS 14700(Part 6/Sec 3):2002
Electromagnetic compatibility
(EMC) Part 6: Generic standards
Section 3: Emission standards for
residential,
commercial and light industrial
environment
Identical
AMENDMENT NO.1 SEPT 2015
TO
IS/IEC 60958(PART 4) : 2003 DIGITAL AUDIO INTERFACE PART 4 PROFESSIONAL
APPLICATIONS (TA4)
This amendment is identical to amendment 1 (2008) to IEC 60958-4(2003) issued by
International Electrotechnical Commission (IEC).
Doc No. LITD 07(3602)
IEC 62623 : 2012
Indian Standard
DESKTOP AND NOTEBOOK COMPUTERS MEASUREMENT OF ENERGY CONSUMPTION
ICS 35.160
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
2015 Price Group
Audio, Video and Multimedia Systems and Equipments Sectional Committee. LITD 07
NATIONAL FOREWORD
This Indian Standard which is identical with IEC 61260-1 : 2014 Desktop and notebook computers Measurement of energy consumption issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the
Audio, Video and Multimedia Systems and Equipments Sectional Committee and approval of
the Electronics and Information Technology Division Council.
The text of ISO/IEC Standard has been approved as suitable for publication as an Indian
Standard without deviations. Certain conventions are, however, not identical to those used in
Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as decimal marker.
The technical committee has reviewed the provisions of following International Standards
referred in this adopted standard and has decided that they are acceptable for use in conjunction
with this standard. For undated references, the latest edition of the references document applies,
including any corrigenda and amendment.
International Standard/ Title
Other publication
IEC 60038:200 ECMA-389 Procedure for the Registration of Categories for ECMA-383
2nd edition
Only the English language text in the International Standard has been retained while adopting it
in this Indian Standard and as such the page numbers are not the same as in the IEC Publication.
For the purpose of deciding whether a particular requirement of this standard is complied with
the final value, observed or calculated, expressing the result of a test or analysis, shall be
rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of
the specified value in this standard.
Doc No. LITD 07(3603)
IS 6964 : IEC 61260-1 : 2014
- -
( )
Indian Standard
ELECTROACOUSTICS OCTAVE-BAND AND FRACTIONAL OCTAVE BAND FILTERS PART 1 SPECIFICATIONS
(Second Revision)
ICS 97.020
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
2015 Price Group
Audio. Video and Multimedia Systems and Equipments Sectional Committee. LITO 07
NATIONAL FOREWORD
This Indian Standard (Second Revision) which is identical with IEC 61260-1 : 2014
Electroacoustics Octave-band and fractional Octave-band filters Part 1 specifications' issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian
Standards on the recommendation of the Audio, Video and Multimedia Systems and Equipments
Sectional Committee and approval of the Electronics and Information Technology Division
Council.
This standard was first revised in 2001 and was identical to IEC 61260 : 1995. This revision is
being published to align it with the latest version of IEC 61260-1 : 2001.
The text of ISO/IEC Standard has been approved as suitable for publication as an Indian
Standard without deviations. Certain conventions are, however, not identical to those used in
Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standard also exist. The corresponding Indian Standard which is to be substituted in its
respective place is listed below along with its degree of equivalence for the edition indicated:
International Standard Corresponding Indian Standard Degree of Equivalence
IEC 61000-4-2
Electromagnetic compatibility
(EMC) Part 4-2: Testing and measurement techniques Electrostatic discharge
immunity test
IS 14700(Part 4/Sec 2) : 2008
Electromagnetic compatibility
(EMC) Part 4 Testing and
measurement techniques Section 2:
Electrostatic discharge immunity
test (first revision)
Identical with IEC
61000-4-2 : 2001
IEC 61000-4-3:2006,
Electromagnetic compatibility
(EMC) Part 4-3: Testing and measurement techniques Radiated, radio-frequency,
electromagnetic field immunity
test
IS 14700(Part 4/Sec 3) : 2008
Electromagnetic compatibility
(EMC) Part 4 : Testing &
measurement techniques Sec 3
Radiated, radio frequency,
electromagnetic field immunity test
(first revision)
Identical
IEC 61000-6-1:2005,
Electromagnetic compatibility
IS 9000 (Part 7/ Sec 7) : 2006 Basic
environmental testing procedures for
Identical with IEC
60068-2-75 : 1997
(EMC) Part 6-1: Generic standards Immunity for residential, commercial and
light-industrial environments
electronic and electrical items: Part
7 Impact test section 7 Test Eh :
Hammer tests
IEC 61000-6-2:2005
Electromagnetic compatibility
(EMC) Part 6-2: Generic standards Immunity for industrial environments
IS 14700(Part 6/Sec 2):2008
Electromagnetic compatibility
(EMC)-Part 6 Generic standards Sec
2 Immunity for industrial
environments
Identical with IEC
61000-6-2:2005
IEC 61000-6-3:2006
Electromagnetic compatibility
(EMC) Part 6-3: Generic standards Emission standard for residential, commercial and
light-industrial environments
Amendment 1:2010
IS 14700(Part 6/Sec 3):2002
Electromagnetic compatibility
(EMC) Part 6: Generic
standards Section 3: Emission
standards for residential,
commercial and light industrial
environment
Identical with IEC
61000-6-3 : 1996
IEC 61672-1, Electroacoustics
Sound level meters Part 1: Specifications
IS 15575(Part 1) : Electroacoustics
Sound level meters Part 1: Specifications
(first revision)
Identical with IEC
61672-1 : 2013
CISPR 22:2008, Information
technology equipment Radio disturbance characteristics Limits and methods of
measurement
IS 6873(Part 7):2012 Limits and
methods of measurements of Radio
disturbance characteristics Part 7
Information technology equipment
(first revision)
Identical
The technical committee has reviewed the provisions of following International Standards
referred in this adopted standard and has decided that they are acceptable for use in conjunction
with this standard. For undated references, the latest edition of the references document applies,
including any corrigenda and amendment.
International Standard Title
ISO/IEC Guide 98-3 Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM: 1995)
ISO/IEC Guide 98-4:2012 Uncertainty of measurement Part 4: Role of measurement uncertainty in conformity assessment
Only the English language text in the International Standard has been retained while adopting it
in this Indian Standard and as such the page numbers are not the same as in the IEC Publication.
For the purpose of deciding whether a particular requirement of this standard is complied with
the final value, observed or calculated, expressing the result of a test or analysis, shall be
rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of
the specified value in this standard.
Doc No. LITD 07(3604)
IEC 60065 : 2014
/ 1
Indian Standard
AUDIO/VIDEO, INFORMATION AND COMMUNICATION
TECHNOLOGY EQUIPMENT PART 1 SAFETY REQUIREMENTS
ICS 33.160.01; 35.020
BIS 2015 BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
2015 Price Group
Audio. Video and Multimedia Systems and Equipments Sectional Committee. LITD 07
NATIONAL FOREWORD
This Indian Standard which is identical with IEC 62368-1 : 2014 'Audio, video and similar
electronic apparatus - Safety requirements' issued by the International Electrotechnical
Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the
Audio, Video and Multimedia Systems and Equipments Sectional Committee and approval of
the Electronics and Information Technology Division Council.
The text of ISO/IEC Standard has been approved as suitable for publication as an Indian
Standard without deviations. Certain conventions are, however, not identical to those used in
Indian Standards. Attention is particularly drawn to the following:
a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard
b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as decimal marker.
In this adopted standard, reference appears to certain International Standards for which Indian
Standards also exist. The corresponding Indian Standards, which are to be substituted in their
respective places, are listed below along with their degree of equivalence for the editions
indicated:
International Standard Corresponding Indian Standard Degree of Equivalence
IEC 60027-1 Letter symbols to
be used in electrical technology Part 1: General
IS 3722 (Parts 1 and 2) : 1983
Letter symbols and signs used in
electrical technology
Technically
Equivalent
IEC 60065, Audio, video and
similar electronic apparatus Safety requirements
IS 616 : 2010 Audio, Video and
Similar Electronic Apparatus -
Safety Requirements
Identical with IEC
60065 : 2005
IEC 60068-2-6, Environmental
testing Part 2-6: Tests Test Fc: Vibration (sinusoidal)
IS 9001 : Part 13 : 1981 Guidance
for environmental testing - Part 13 :
Vibration (sinusoidal) test
Technically
Equivalent
IEC 60068-2-78, Environmental
testing Part 2-78: Tests Test Cab: Damp heat, steady state
IS 9000 (Part 4) : 2008 Basic
environmental testing procedures
for electronic and electrical items:
Part 4 Damp heat (steady state)
(first revision)
Identical with IEC
60068-2-78 : 2001
IEC/TR 60083, Plugs and
socket-outlets for domestic and
similar general use standardized
in member countries of IEC
IS 1293 : 2005 Plugs and socket-
outlets of rated voltage up to and
including 250 volts and rated
current up to and including 16
Technically
Equivalent
amperes specification IEC 60085, Electrical insulation
Thermal evaluation and designation
IS 1271 : 2012 Electrical
Insulation-thermal evaluation and
designation (second revision)
Identical with IEC
60085 : 2007
IEC 60086-4 Primary batteries Part 4: Safety of lithium batteries
IS 6303 (Part 4) : 2013 Primary
batteries Part 4: Safety of lithium batteries (second revision)
Identical with IEC
60086-4 : 2007
IEC 60107-1 : 1997 Methods of
measurement on receivers for
television broadcast transmissions Part 1 : General considerations Measurements at radio and video frequencies
IS 4545(Part 1) : 2008 Methods of
measurement on receivers for
television broadcast transmissions Part 1 : General considerations
(second revision)
Technically Equivalent
IEC 60112 Method for the
determination of the proof and
the comparative tracking indices
of solid insulating materials
IS 2824 : 2007 Method for
determining of the proof and the
comparative tracking indices of
solid insulating materials
(second revision)
Identical with IEC
60112 : 2003
IEC 60127 (all parts) Miniature
fuses IS/IEC 60127 (All Parts) Miniature
fuses (first revision)
Identical
IEC 60227-1, Polyvinyl chloride
insulated cables of rated voltages
up to and including 450/750 V Part 1: General requirements
IS 694 : 2010 Polyvinyl Chloride
insulated unsheathed and sheathed
cables/cords with rigid and flexible
conductor for rated voltages up to
and including 450/750 V Technically Equivalent IEC 60227-2:2003, Polyvinyl
chloride insulated cables of rated
voltages up to and including 450/750 V Part 2: Test methods
IEC 60245-1, Rubber insulated
cables Rated voltages up to and including 450/750 V Part 1: General requirements
IS 9968 (Part 1) : 1998 Elastomer
insulated cables : Part 1 For
working voltages upto and
including 1100 V (first revision)
IS 9968 (Part 2) : 2002 Elastomer
insulated cables : Part 1 For
working voltages from 3.3 kV up to
and including 3 kV(first revision)
Technically Equivalent
IEC 60309 (all parts), Plugs,
socket-outlets and couplers for
industrial purposes
lS/lEC 60309-1:2002 Plugs,
socketoutlets and couplers for IEC 60309-1 (1999)
industrial purposes Part 1 : General requirements
lS/lEC 60309-2:2002 Plugs,
socketoutlets and couplers for
industrial purposes Part 2: Dimensional interchangeability
requirements for pin and contact-
tube accessories
IEC 60309-2 (1999)
IEC 60317 (all parts),
Specifications for particular
types of winding wires
IS 13730(various parts)
Specifications for particular types of winding wires
Identical
IEC 60317-43 Specifications for
particular types of winding wires
Part 43: Aromatic polyimide type wrapped round copper wire,
class 240
IS 13730(Part 43) : 2013
Specifications for particular types
of winding wires Part 43: Aromatic polyimide type wrapped
round copper wire, class 240
(first revision)
Identical with IEC
60317-43 : 2010
IEC 60320 (All parts) Appliance
couplers for household and
similar general purposes
lS/lEC 60320 (All parts) Appliance
couplers for household and similar
general purposes Identical
IEC 60320-1 Appliance couplers
for household and similar
general purposes Part 1: General requirements
IS/IEC 60320 (Part 1) : 2001
Appliance couplers for household
and similar general purposes Part 1: General requirements
Identical with IEC
60320-1 : 2001
EC 60320-2-2, Appliance
couplers for household and
similar general purposes Part 2-2: Interconnection couplers for
household and similar equipment
lS/lEC 60320-2-2:1998 Appliance
couplers for household and similar
general purposes Part 2-2: Interconnection couplers for
household and similar equipment
IEC 60320-2-2:1998
IEC 60384-14:2005 Fixed
capacitors for use in electronic
equipment Part 14: Sectional specification: Fixed capacitors
for electromagnetic interference
suppression and connection to
the supply mains
IS QC 302400 : 1994 Fixed
capacitors for use in electronic
equipment Part 14 : sectional
specification : Fixed capacitors for
electromagnetic interference
suppression and connection to the
supply mains supply mains
Identical with IEC Pub
38414/QC 302400
(1993-07)
IEC 60417 Graphical symbols
for use on equipment
IS 2032 (All Parts) Graphical
symbols used in electrotechnology Technically Equivalent
IEC 60529, Degrees of
protection provided by
enclosures (IP Code)
IS/IEC 60529:2001 Degrees of
protection provided by enclosures
(IP Code) (superseding IS 12063)
Identical with IEC
60529 : 2001
IEC 60664-1:2007 Insulation
coordination for equipment
within low-voltage systems Part 1: Principles, requirements
and tests
IS 15382 ( Part 1) : 2014 Insulation
coordination for equipment within
low-voltage systems : Part 1
Principles, requirements and tests
(first revision)
Identical with IEC
60664-1 : 2007
IEC 60664-3 Insulation
coordination for equipment
within low-voltage systems Part 3: Use of coating, potting or
moulding for protection against
pollution
IS 15382(Part 3) : 2006 Insulation
coordination for equipment within
low-voltage systems Part 3 Use of
coating, potting or moulding for
protection against pollution
Identical with IEC
60664-3 : 2003
IEC 60691:2002 Thermal links Requirements and application
guide
IS/IEC Pub 691 : 1993 Thermal
links - Requirements and
application guide
Identical with IEC Pub
691 : 1993
IEC 60695-11-5:2004 Fire
hazard testing Part 11-5: Test flames Needle-flame test method Apparatus, confirmatory test arrangement
and guidance
IS 11000 (Part 2/Sec 2) : 2008 Fire
hazard testing - Part 11-5: Test
flames - Needle-flame test method -
Apparatus confirmatory test
arrangement and guidance
(first revision)
Identical with IEC
60695-11-5:2004
IEC 60730 (all parts), Automatic
electrical controls for household
and similar use
IS 60730(Part 1):1999 Automatic
electrical controls for household
and similar use: Part 1 General
requirements
Identical with IEC
60730-1 : 1999
IEC 60730-1:2010, Automatic
electrical controls for household
and similar use Part 1General requirements
IS/IEC 60730-1 : 1999 Automatic
electric controls for household and
similar use Part 1 General
requirements
Identical with IEC
60730 : 1999
IEC 60738-1:2009,
Thermistors Directly heated positive temperature
coefficient Part 1: Generic specification
IS 11534(Part 1):1985 Directly
heated positive step function
temperature co-efficient
thermistors: Part 1 General
requirements and methods of tests
Technically equivalent
IEC 60747-5-5:2007
Semiconductor devices Discrete devices Part 5-5 Optoelectronic devices Photocouplers
IS 14901 (Part 5): 2004
Semiconductor devices Discrete devices and integrated circuits Part
5 Optoelectronic devices
Identical with IEC
60747-5 : 1992
http://10.53.100.14/php/BIS/ShowDocument.php?row=2654
IEC 60825-2:2004, Safety of
laser products Part 2: Safety of optical fibre communication systems (OFCS)
IS 14624 (Part 2) : 2012 Safety of
laser products Part 2: Safety of optical fibre communication
systems (OFCS) (first revision)
IEC 60825-2 : 2005
IEC 60851-3:2009 Winding
wires Test methods Part 3: Mechanical properties
IS 13778 : Part 3 : 2012 Winding
wires - Test methods Part 3
Mechnical Properties
Identical
IEC 60851-5:2008 Winding
wires Test methods Part 5: Electrical properties
IS 13778 (Part 5) : 2012 Winding
Wires Test Methods Part 5 Electrical Properties
Identical
IEC 60851-6:1996, Winding
wires Test methods Part 6: Thermal properties
IS 13778 (Part 6): 2011 Winding
Wires - Test Methods : Part 6
Thermal properties
Identical with IEC
60851-6 : 1996
IEC 60906-1, IEC system of
plugs and socket-outlets for
household and similar purposes Part 1: Plugs and socket-outlets
16 A 250 V a.c. IEC 60906-2, IEC system of
plugs and socket-outlets for
household and similar purposes Part 2: Plugs and socket-outlets
15 A 125 V a.c.
IS 1293 : 2005 Plugs and socket-
outlets of rated voltage up to and
including 250 volts and rated
current up to and including 16
amperes Specification (third revision)
Technically Equivalent
IEC 60947-1, Low-voltage
switchgear and controlgear Part 1: General rules
IS/IEC 60947-1 : 2007 Low-
voltage switchgear and controlgear
Part 1: General rules IEC 60947-1 : 2007
IEC 60950-1:2005, Information
technology equipment Safety Part 1: General requirements
IS 13252 : Part 1:2010 Information
Technology Equipment Safety Part 1 General Requirements
Identical
IEC 60950-22:2005, Information
technology equipment Safety Part 22: Equipment to be installed outdoors
IS 13252 (Part 22) : 2014
Information technology equipment
Safety Part 22: Equipment to be installed outdoors
IEC 60950-22 : 2005
IEC 60950-23, Information
technology equipment Safety Part 23: Large data storage equipment
IS 13252 (Part 23) : 2014
Information technology equipment Safety Part 23: Large data storage equipment
IEC 60950-23 : 2005
IEC 60990:1999, Methods of
measurement of touch current
and protective conductor current
lS/lEC 60990:1999 Methods of
measurement of touch current and
protective conductor current
Identical with IEC
60990 : 1999
IEC 61051-1, Varistors for use in
electronic equipment Part 1: Generic specification
IS QC 420000 : 1994 Varistors for
Use in Electronic Equipment -
Generic Specification
Identical with IEC QC
420000 : 1991
IEC 61051-2:1991 Varistors for
use in electronic equipment Part 2: Sectional specification for
surge suppression varistors
IS QC 420100 : 1994 Varistors for
use in electronic equipment Sectional specification for surge
suppression varistors
Identical with IEC QC
420100 : 1991
IEC 61056-1, General purpose
lead-acid batteries (valve-
regulated types) Part 1: General requirements, functional
characteristics Methods of test
IS 16220 (Part 1) : 2015 General
purpose lead-acid batteries (valve-
regulated types) Part 1: General requirements, functional
characteristics Methods of test
IEC 61056-1 : 2012
IEC 61058-1:2008, Switches for
appliances Part 1: General requirements
IS/IEC 61058-1:2000 Switches for
appliances : Part 1 General
requirements
Identical
IEC 61140:2001, Protection
against electric shock Common aspects for installation and equipment
IS 9409:1980 Classification of
electrical and electronic equipment
with regard to protection against
electric shock
Technically equivalent
IEC 61558-1:2005 Safety of
power transformers, power
supplies, reactors and
similar products Part 1: General requirements and tests
IS/IEC 61558-1:1997 Safety of
power transformers, power supply
units and similar : Part 1 General
requirements and tests
Identical with IEC
61558-1 : 1997
IEC 61643-11, Low-voltage
surge protective devices Part 11: Surge protective devices connected to low-voltage power
systems Requirements and test methods
DOC.ETD 7(6587)
Low voltage surge protective
devices - Part 11: Surge protective
devices connected to low-voltage
power distribution systems
Identical
IEC 61965:2003, Mechanical
safety of cathode ray tubes
IS/IEC 61965:2003 Mechanical
Safety Of Cathode Ray Tubes Identical with IEC
61965 : 2003
IEC 62133, Secondary cells and
batteries containing alkaline or
other non-acid electrolytes Safety requirements for portable
sealed secondary cells, and for
batteries made from them, for use in portable applications
IS 16046 : 2012 Secondary Cells
and Batteries containing Alkaline
or other non-acid Electrolytes -
Safety Requirements for Portable
Sealed Secondary Cells, and for
Batteries made from them, for use
in portable Applications
Identical with IEC
62133 : 2002
IEC 62471:2006
Photobiological safety of lamps
and lamp systems
IS 16108:2012 Photobiological
Safety of lamps and lamp Systems Identical
ISO 178, Plastics Determination of flexural
properties
IS 3360 ( Part S/Set 7 ) : 1996
Plastics - Determination of flexural
properties
IS0 178 : 1993
ISO 179-1, Plastics IS 13360 ( Part S/Set 5 ) : 1996 IS0 179 ,: 1993
http://10.53.100.14/php/BIS/ShowDocument.php?row=16773
Determination of Charpy impact
properties Part 1: Non-instrumented impact test
Plastics - Determination of charpy impact strength
ISO 180, Plastics Determination of Izod impact
strength
IS 13360 (Part 5/Sec 4) : 2013
Plastics Determination of Izod impact strength
ISO 180 : 2000
ISO 306, Plastics Thermoplastic materials Determination of Vicat softening
temperature (VST)
IS 13360 (Part 6/Set 1) : 1999
Plastics Methods of testing : Part 6 Thermal properties, Section 1
Determination of vicat softening
temperature of thermoplastic
materials (first revision)
Identical with ISO 306 :
1994
ISO 527 (all parts), Plastics Determination of tensile
properties
IS 13360 ( Part 5 ) : 1996 Plastics -
Determination of tensile properties
- General principles (All sections)
IS0 527 : 1993
ISO 871, Plastics Determination of ignition
temperature using a hot-air
furnace
IS 13360 (Part 6/See 21 ): 2004
Plastics Determination of ignition temperature using a hot-air
furnace
ISO 871:1996
ISO 3864 (all parts), Graphical
symbols Safety colours and safety signs
IS 9457:2005 Safety colours and
safety signs code of practice (first revision)
Technically equivalent
ISO 9773, Plastics Determination of burning
behaviour of thin flexible
vertical specimens in
contact with a small-flame
ignition source
IS 13360(Part 6/Sec 23):2006
Plastics - Methods of Testing :part
6 Thermal Properties, Section 23
Determination of Burning
Behaviour of Thin Flexible Vertical
Specimens in Contact With Small-
flame Ignition Source
Identical with ISO 9773
: 1998
The technical committee has reviewed the provisions of following International Standards
referred in this adopted standard and has decided that they are acceptable for use in conjunction
with this standard. For undated references, the latest edition of the references document applies,
including any corrigenda and amendment.
International
Standard/ Publication
Title
IEC 60086-5 Primary batteries Part 5: Safety of batteries with aqueous electrolyte IEC 60332-1-2
Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for vertical flame propagation for a single insulated wire or cable Procedure for 1 kW premixed flame
IEC 60332-1-3 Tests on electric and optical fibre cables under fire conditions Part 1-3: Test for vertical flame propagation for a single insulated wire or cable
Procedure for determination of flaming droplets/particles
IEC 60332-2-2 Tests on electric and optical fibre cables under fire conditions Part 2-2: Test for vertical flame propagation for a single small insulated wire or
cable Procedure for diffusion flame IEC 60695-10-2 Fire hazard testing Part 10-2: Abnormal heat Ball pressure test IEC 60695-10-3 Fire hazard testing Part 10-3: Abnormal heat Mould stress relief
distortion test
IEC 60695-11-10 Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical
flame test methods
IEC 60695-11-
20:1999
Fire hazard testing Part 11-20: Test flames 500 W flame test methods
IEC/TS 60695-11-21 Fire hazard testing Part 11-21: Test flames 500 W vertical flame test method for tubular polymeric materials
IEC 60728-11:2005 Cable networks for television signals, sound signals and interactive
services Part 11: Safety IEC 60825-1:2007 Safety of laser products Part 1: Equipment classification and
requirements
IEC 60896-11 Stationary lead-acid batteries Part 11: Vented types General requirements and methods of tests
IEC 60896-21:2004 Stationary lead-acid batteries Part 21: Valve regulated types Methods of test
IEC 60896-22 Stationary lead-acid batteries Part 22: Valve regulated types Requirements
IEC 60998-1 Connecting devices for low-voltage circuits for household and similar
purposes Part 1: General requirements IEC 60999-1 Connecting devices Electrical copper conductors Safety
requirements for screw-type and screwless-type clamping units Part 1: General requirements and particular requirements for clamping units for
conductors from 0,2 mm2 up to 35 mm2 (included)
IEC 60999-2 Connecting devices Electrical copper conductors Safety requirements for screw-type and screwless-type clamping units Part 2: Particular requirements for clamping units for conductors above 35
mm2 up to 300 mm2 (included)
IEC 61056-2 General purpose lead-acid batteries (valve-regulated types) Part 2: Dimensions, terminals and marking
IEC/TS 61201:2007 Use of conventional touch voltage limits Application guide IEC 61204-7 Low-voltage power supplies, d.c. output Part 7: Safety requirements
IEC 61293 Marking of electrical equipment with ratings related to electrical supply
Safety requirements IEC 61427 Secondary cells and batteries for photovoltaic energy systems (PVES)
General requirements and methods of test
IEC/TS 61430 Secondary cells and batteries Test methods for checking the performance of devices designed for reducing explosion hazards Lead-acid starter batteries
IEC 61434 Secondary cells and batteries containing alkaline or other non-acid
electrolytes Guide to designation of current in alkaline secondary cell and battery standards
IEC 61558-2-16 Safety of transformers, reactors, power supply units and similar products
for voltages up to 1 100 V Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode
power supply units1
IEC 61810-1:2008 Electromechanical elementary relays Part 1: General requirements IEC 61959 Secondary cells and batteries containing alkaline or other non-acid
electrolytes Mechanical tests for sealed portable secondary cells and batteries
IEC 61984 Connectors Safety requirements and tests IEC 62281 Safety of primary and secondary lithium cells and batteries during
transport
IEC 62485-2 Safety requirements for secondary batteries and battery installations Part 2: Stationary batteries
ISO 3864-2 Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labels
ISO 4892-1 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
ISO 4892-2:2006 Plastics Methods of exposure to laboratory light sources Part 2: Xenonarc lamps
ISO 4892-4 Plastics Methods of exposure to laboratory light sources Part 4: Open-flame carbon-arc lamps
ISO 7000 Graphical symbols for use on equipment Index and synopsis, available from
ISO 7010 Graphical symbols Safety colours and safety signs Safety signs used in
workplaces and public areas
ISO 8256 Plastics Determination of tensile-impact strength ISO 9772 Cellular plastics Determination of horizontal burning characteristics of
small specimens subjected to a small flame
EN 50332-1 Sound system equipment: Headphones and earphones associated with
portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 1: General method for "one package equipment
EN 50332-2 Sound system equipment: Headphones and earphones associated with
portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 2: Matching of sets with headphones if either or both are offered separately
For the purpose of deciding whether a particular requirement of this standard is complied with
the final value, observed or calculated, expressing the result of a test or analysis, shall be
rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of
the specified value in this standard.
- 2: - ( )Indian Standard ( )Indian Standard 2 ( )Indian Standard , 10 ( )Indian StandardIndian Standard