Spooky2 Contact Mode Instructions

Post on 21-Jan-2018

254 views 5 download

Transcript of Spooky2 Contact Mode Instructions

Spooky2 Spooky2 Contact Mode Instructions

Our Users & Team

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Here are detailed instructions on Spooky2 contact mode with Spooky Hand

Cylinders and Spooky Tens Pads.

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Connection

Spooky Hand Cylinders

There are three different ways to connect Spooky Hand Cylinders depending

on whether you use Spooky Boost 2.0 or not, and they’ re both very simple.

First, connection via Spooky Boost 2.0:

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

A. Spooky Hand Cylinders with Spooky Boost 2.0

Connect the BNC-to-alligator clips cable that came with your generator to the

Colloidal Silver output of Spooky Boost 2.0. Then connect each alligator clip to

a cylinder as detailed below.

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

B. Spooky Hand Cylinders Direct Connect

Connect the BNC-to-alligator clips cable that came with your generator to Out 1

of the generator.

Then insert the alligator clips into the holes located at the plastic end of each

Spooky Hand Cylinder.The image below right shows the correct orientation for

your Spooky Hand Cylinders.

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

C. Without Boost 2.0 to Get Quadruple Power.

Connect both cables to Out 1 and Out 2. Now separate the red clips from the black ones - we won’t be connecting the black clips, so you can wrap each one in paper masking tape.

Now connect one red clip to a Spooky Tube electrode, and do the same for the other red clip - each red clip should be attached to an electrode.

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Spooky Tens Pads

The connection of Spooky Tens Pads is the same as Spooky Hand

Cylinders (except that the adapter cable is Tens Cable).

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Note:

1. Contact Mode needs higher amplitudes to achieve adequate body

penetration (14–20 volts).

2. Make sure the alligators have direct contact with the steel part of the tube

for good connection.

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Contact Mode settings

There are JW-Killing ( Contact) and JW-Healing(Contact) presets in Spooky2

software.

They are applicable to both Hand Cylinders and Tens Pads.

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:echolee@cleanenergy-npt.comor service@spooky2.com

Thank you!