Post on 03-Apr-2018
KORTICK MANUFACTURING COMPANY2230 Davis Court Hayward, CA 94545
POLE LINE HARDWAREConstruction Specialties
CATALOG NO. 212
WWW.KORTICK.COM
PHONE: 510.856.3600 EMAIL: SALES@KORTICK.COM
© Copyright 2010 by Kortick Mfg. Co.All images and information contained within are the sole property of Kortick Manufacturing LLC and cannot be reproduced or used
without Kortick’s prior written consent.
ii
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
Golden Gate Bridge built with Kortick hardware
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
iiiii TABLE OF CONTENTS
Introduction 1History 2Kortick: The Solution Provider 4Terms and Conditions 5Bolt & Shear Strength Chart 6Standard ASTM Reference Notes 7
POLE LINE HARDWARE 8FASTENERS 8ANCHORING AND GUYING 37POLE BANDS AND STUBBING 44POLE STEPS 50SECONDARY & SERVICE HARDWARE 53INSULATOR PINS AND STUDS 66BRACES 74CROSSARMS & GAINS 82BRACKETS 88EXTENSION LINK 98SPECIALTY: POLE EXTENSION, ANTI CLIMBING 101
UNDERGROUND HARDWARE 103LADDERS 103CABLE RACKS AND HOOKS 105OTHER UNDERGROUND HARDWARE 107
TELEPHONE 111
MARINE 114
CONSTRUCTION 116
FABRICATION 118SUBSTATION STRUCTURES 118STATIC WIRE GOAT PEAKS 119
INSERTSTHERMAL DIFFUSION GALVANIZING 21HARDWOOD PRODUCT 84
iv
J. C. Kortickfounder
1875 - 1933
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
1iv INTRODUCTIONWe take pleasure in introducing Kortick Catalog 212 of our Pole Line Hardware and Construction Specialty Products. Kortick is the solutions provider for hardware needs.
As the pioneer Pole Line Hardware manufacturer on the Pacific Coast, we have served the industry since 1898, building our business and our reputation for service and quality. To our customers we express appreciation for making our growth and development possible--both in the past and in the years ahead. We pride ourselves on the quality of our products, manufactured domestically, with a century of experience behind their production. Therefore, when you buy Kortick, you can rest assured that you are buying a quality product.
Kortick aspires to be a company in which all of its employees and its surrounding community can take pride. Our mission is to maintain the most accessible knowledge in the hardware industry, the best delivery times, while continuing to offer excellent service and affordable prices. We aim to do this while bringing manufacturing jobs back to America and making positive changes to our environment.
At Kortick Manufacturing we value:Growing domestic manufacturing and employmentEnvironmental stewardship and social responsibilityGood business practices We guarantee:Cost competitive product The best and most accessible knowledge in the industry Fast deliveryQuality product
Thank you for your Continued Support,
Gavin FrasePresident Kortick Manufacturinggfrase@kortick.com
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
2HISTORYIn 1898, the late Mr. J. C. Kortick was importuned by Pacific Tel. & Tel. Co., the then operating telephone company in San Francisco, to make certain steel braces and bolts for their pole line construction needs. In 1900, the telephone company reincorporated as the Pacific States Telephone and Telegraph Co., and broadened their operating area. Kortick stepped up his production, at their request, and continued to supply more and more of their pole line hardware requirements over the greater operating area.In 1906, April 18 to be exact, San Francisco was badly shaken up by earthquakes and about one-quarter of its land area, including the Kortick plant, was reduced to ashes by fire.
The telephone company restored temporary service within days, but needed hardware for the more permanent type of pole line construction. The problem then, how soon can the Kortick plant start making pole line hardware? While Kortick dug what machinery he could salvage out of the ashes and put it into operating condition, the telephone company barged a load of lumber over from Oakland, and hauled it with their own teams to the site of the Kortick plant. Kortick constructed a shed, set up his machinery, and by the First of May that year, he was turning out pole line hardware and the telephone company was mounting it on the poles BLACK. Since steel was not immediately available, a lot of Kortick’s first production was salvaged hardware from the ruins of burned down poles.
In 1912, extensive telephone line construction developed in British Columbia, and through the Northern Electric Co. of Canada (Western Electric Co. of U/ S.) Kortick fabricated and shipped under contract some 100 or more tons of pole line hardware – in those days no small order for the Pacific Coast.
Kortick expanded to southwestern utilities and telephone companies in 1919.
In 1924, the General Purchasing Department of the Western Electric Co. at New York realized the volume of pole line hardware and other telephone supplies purchased on behalf of their Pacific Coast subsidiaries had developed in vol-ume sufficiently to justify the establishment of a Pacific Coast Purchasing Department under a Pacific Coast Purchas-ing Agent. At that time Kortick became the first contract supplier for pole line hardware on the Pacific Coast for the telephone companies, through the Western Electric Co., in successful competition against all eastern manufacturers.
In 1925, Southern California Edison, Co. erected the first 220 KV line on the Pacific Coast and used specially designed hardware. Kortick was the only Pacific Coast manufacturer submitting a quote. The Southern California Edison Co. was elated to be able to make this purchase on the Pacific Coast, and was highly pleased with the material delivered and the service rendered.
In 1925, we also began shipping pole line hardware into the Pacific Northwest at the invitation of the Power Company, and set up sales representatives to service our interests.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
32
During the 3-year period from 1947 to 1949, a representative of the Kortick Manufacturing Company represented the pole line hardware manufacturers on the Pacific Coast and sit on the EEI Committee on Standard Packaging. Kortick had been using wire bound boxes since 1945 and had made considerable progress in standard packaging and packaging in their own plant. The results of this experience were available to the eastern EEI Committee and were used extensively in the final adoption of the present industry Standard Packaging Program.
During the war years, Kortick produced many thousand tons of pole line hardware for government projects in the Pacific and in the Orient.By 1940, we had outgrown our quarters, so Kortick purchased new property four times as large in the area and proceeded to build a new plant. The plant building was 95% completed in December 1941 when war broke out, and the US Navy and Mari-time Commission commandeered that building for the war effort until 1950. The office and warehouse section was completed and ready for occupancy in 1953. This move to a more desirable location and to more convenient and efficient operation conditions tripled our plant production facilities and doubled our San Francisco warehouse facilities, the better to back up pole line hardware stocks in Maydwell and Hartzell warehouses in Seattle, Portland, San Francisco, Los Angeles, Sand Diego, and Phoenix, and of our distributor in Honolulu.
Kortick added an aerospace industry press in the late 20th century, modern welding equipment, and other manufacturing upgrades. Most recently, in the 2000’s, Kortick added computer controlled milling operations and two modern presses to our arsenal. Kortick continues to employ top-flight industrial, mechanical, and electrical engineers, allowing con-tinual improvement in product design and operational efficiency.
Kortick Manufacturing Company is a California corporation, owned and operated by San Francisco Bay Area residents. Operational profit goes back into the business continually to provide for the expansion of the business. In 2002, the company moved from its long time home in San Francisco to Hayward, California, a few short miles across the bay, where operations continued without interruption. In fact, in a miraculous feat of commitment to its customers, the company did not miss a single day of shipping product, while at the same time moving its operations via 175 truckloads across the Bay. Kortick looks forward to building on the commitment to customers that started in the 19th century as it presses forward into the 21st.
HISTORY
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
4KORTICK: “THE SOLUTION PROVIDER”Design Engineering and Custom Manufacturing. We say “Yes”
An Excerpt from Kortick’s History:
During the early 1900’s necessity was the mother of invention. A ‘Consultant Engineer’ was not listed in the phone book and design-engineering staffs were still unkown. When the Power Company, Utility Company, or Telephone Company had a construction ‘problem’ they had to tackle it fast. Many times Mr. Kortick sat down with the utility construction men, hashed over their problems, and then burned the midnight oil until a solution was found and pro-duction could start. Many pole line hardware items used on the coast today were ‘born’ in the Kortick plant in just that way. Many items were recently redesigned or otherwise improved to meet current load conditions or to adapt them to our more modern and economical standard.
Today, Kortick holds true to this philosophy. We take pride in our Catalog and “Standards” but also keep a staff of engineers with extensive experience in the T&D field to assist customers in specialized design needs. If you do not see exactly what you are looking for in the catalog, please call our Sales Staff. Kortick’s production capabilities allow for flexibility in both production run size and product design.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
54 TERMS & CONDITIONSApplicability of Terms and Conditions: These Terms and Conditions will govern all sales by Kortick Manufacturing (herein called “Seller”), unless otherwise agreed to in writing by an employee of Seller. Terms and Conditions that are different from or in addition to these Terms and Conditions are objected to and will not be binding on Seller.
Drawings and Catalog Representations: All Drawings subject to change without notification. Drawings are catalog representations not to be used for engineering purposes.
Quotations, Orders, and Prices: All prices and specifications contained on Seller’s quotation are subject to change without notice unless indicated otherwise on the quotation. All quotations on items are made subject to prior sale on such goods. The minimum billing charge on any order placed with Seller shall be $50.00.
Shipment, Freight, and Delivery: All prices are F.O.B. Kortick Manufacturing, Hayward, California, with freight prepaid and added to invoice, or freight collect. If freight charges are to be prepaid and added, Seller shall use the carrier it deems the most economical and efficient method of shipment unless otherwise specified by Buyer. Seller’s placement of purchased goods at the point of shipment in the possession of a trucking company or other carrier, or on the Buyer’s vehicle shall constitute delivery to Buyer, and thereafter Buyer shall bear all expense and risk of loss.
Terms: Net thirty (30) days from the date of Seller’s invoice. A service charge of one and one half percent (1-1/2%) may be added to past due invoices, but only to the extent provided by law.
Deviations in manufactured quantities: Kortick may request qty variations of +_10% on production runs.
Acceptance: Buyer shall notify Seller of any defect, error, or shortage of any items received by Buyer within 14 days after delivery. Buyer shall provide purchase order number and any other documents that substantiate the alleged defect, error, or shortage. If Buyer fails to provide such notice and documents within the required time, Buyer will be deemed to have waived such error, shortage, or defect.
Tolerances and Variations: Except in the particulars specified by Buyers and agreed to in writing by Seller, the goods being sold to Buyer will be produced in accordance with Seller’s standard practices. All goods, however, including those produced to meet an exact specification, will be subject to tolerance and variations consistent with good manufacturing practices in regard to dimension, weight, section, composition, mechanical and electrical properties; to normal variations in surface and internal conditions and in quality; and in deviations from tolerances and variations consistent with practical testing and inspection methods.
Warranty and Disclaimers of Warranty: Seller warrants to Buyer that the goods supplied hereunder will be free from defects in material and workmanship under normal and proper usage for a period of one year from the date of shipment by Seller. Seller makes no warranties with respect to any goods subjected to abuse, misuse, misapplication, neglect, alteration or accident; to improper and incorrect installation or maintenance; or to abnormal conditions of use.
Returns: No goods may be returned without first having secured prior written authorization from Seller, in the form of a Return Materials Authorization. Only standard, non-obsolete, non-special order items in original cartons and in resalable condition may be returned, freight prepaid. Return items are subject to a minimum restocking fee of 25% of original purchase price. Such return requests must be initiated within 30 days of shipment.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
6BOLT & SHEAR STRENGTH CHARTKortick Bolt Shear and Tensile Strengths
(lbs)Bolt Diameter Single Shear Single Shear Tensile Strength
Through Threads Through Shaft3/8 42501/2 5200 7950 78005/8 8330 12420 124003/4 12440 17890 183507/8 17270 24350 254001 22690 31800 33500
1 1/4 36590 49700 53300
UTILITY SPECSCommon Spec listings for Utility Products that Kortick adheres to. Please contact Kortick Engineering Department for specific properties and details
ANSI C135 series
CSA
EEI-NEMA
General Order 95 (California)
RUS (see rear index)
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
76 STANDARD ASTM REFERENCE NOTESCommon Spec abstracts in Hardware. Please contact Kortick Engineering Department for specific properties. http://www.astm.org/
A123 This specification covers the standard requirements for hot-dip galvanized zinc coatings on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, and strips. This specification deals with both un fabricated products and fabricated products, for example, assembled steel products, structural steel fabrications, large tubes already bent or welded before galvanizing, and wire work fabricated from uncoated steel wire. Also covered here are steel forgings and iron castings incorporated into pieces fabricated before galvanizing or those too large to be centrifuged (or otherwise handled to remove excess galvanizing bath metal).
A153 This specification covers standards for zinc coatings applied through hot-drip process on iron and steel hardware. The hot-dip galvanizing process shall form layers of Zn/Fe alloy adhering to the steel surface. This specification is applicable to steel hardware items of Classes A, B, C, and D. The thickness or weight/mass of zinc coating shall conform to specified values for various classes of materials. The coated articles shall be free from uncoated areas, blisters, flux deposits, dross inclusions, and other defects. The coating shall be smooth and reasonably uniform in thickness. Tests shall be performed to determine the minimum coating weight or minimum coating thickness, finish and appearance, embrittlement, adherence, average weight/mass of coating, and average thickness of coating. Guidelines are also given for inspection, rejection and retest, packaging, and certification procedures.
A1059 1.1 This specification covers the general requirements for protective zinc coatings (hereinafter referred to as the coatings) to be applied by the thermo-diffusion coating (TDC) method, to various products made of carbon steel, including low and high tensile parts as well as of wrought iron, sintered iron steel-powder and various steel and stainless alloys. TDC is carried out by immersing the parts in a zinc alloy powder at elevated temperature for a period of time, causing a metallurgical diffusion process of zinc and iron. Further processing may be added, such as, passivation, topcoat application, paint application, etc.
1.2 This specification is applicable to orders in either inch-pound units (as A 1059) or in SI units (as A 1059M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in brackets. Each system shall be used independently of the other without combining values in any way. In the case of orders in SI units, all testing and inspection shall be done using the metric equivalent of the test or inspection method as appropriate. In the case of orders in inch-pound units, such shall be stated to the applicator when the order is placed.
A36 This specification covers carbon structural steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes. Heat analysis shall be used to determine the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, and copper. Tensile strength, yield strength, and elongation shall be evaluated using tension test and must conform to the required tensile properties.
A307 This specification covers the chemical and mechanical requirements for three grades (Grades A, B, and C) of carbon steel bolts and studs in specified sizes. This specification does not cover the requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors, or other similar externally threaded fasteners. When tested, sampled specimens shall adhere to specified values for chemical composition, hardness, tensile strength, yield point, elongation, and dimensions.
A325 This specification covers the chemical, mechanical, and dimensional requirements for two types of heavy hex structural bolts made of quenched and tempered steel that are intended for use in structural connections. These bolts are designated by type, denoting chemical composition, as follows: Type 1—medium carbon, carbon boron, or medium carbon alloy steel; and Type 3—weathering steel. The steel bolts shall undergo heat and product analysis for chemical composition measurements. The bolts shall also undergo test that shall examine their conformance to specified properties such as dimensions and thread fit, surface discontinuities, coating weight and thickness, hardness, tensile strength, yield strength, elongation, reduction of area, proof load, and rotational capacity.
ASTM F1470 Sampling Protocol
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
8
POLE LINE HARDWARE
SQUARE HEAD MACHINE BOLTS
NOTES:1. ASTM A307 AND HOT DIPPED GALVANIZED A1532. CHAMFERED TIP3. ASSEMBLED WITH ONE SQUARE NUT
K
“C”
Ø “A”
SQUARENUT
“B”
Square Head Machine BoltsASTM A307 and Hot Dip Galvanized ASTM A153.Bolts Assembled with one square nut.Bolts are Coarse Threaded to a class 2 Fit, formed with a chamfered tip for ease of nut assembly.Washers ordered separately.
Kortick Square Machine Bolts measured from the beginning of the first thread to the underside of the head.Used for the construction, maintenance, and service divisions of every utility in the country.Also called cross arm machine bolts, through bolts, and cable suspension bolts.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
98
POLE LINE HARDWARE
SQUARE HEAD MACHINE BOLTS"A" "B" "C" "A" "B" "C" "A" "B" "C"
(DIA,) (L) THD (DIA,) (L) THD (DIA,) (L) THD
K1002 3/8" 2" 1.000 K1201-3/4 5/8" 1-3/4" 1.250 K1762 7/8" 12" 6.000
K1004-1/2 3/8" 4-1/2" 3.000 K1202 5/8" 2" 1.250 K1764 7/8" 14" 6.000
K1005 3/8" 5" 3.000 K1202-1/2 5/8" 2-1/2" 1.500 K1766 7/8" 16" 6.000
K1005-1/2 3/8" 5-1/2" 3.000 K1203 5/8" 3" 1.500 K1768 7/8" 18" 6.000
K1006 3/8" 6" 3.000 K1204 5/8" 4" 1.500 K1770 7/8" 20" 6.000
K1007 3/8" 7" 3.000 K1205 5/8" 5" 3.000 K1772 7/8" 22" 6.000
K1008 3/8" 8" 3.000 K1206 5/8" 6" 3.000 K1774 7/8" 24" 6.000
K1009 3/8" 9" 3.000 K1207 5/8" 7" 3.000 K1776 7/8" 26" 6.000K1208 5/8" 8" 4.000 K1778 7/8" 28" 6.000
K1101 1/2" 1" 0.750 K1209 5/8" 9" 4.000 K1780 7/8" 30" 6.000K1101-1/2 1/2" 1-1/2" 1.000 K1210 5/8" 10" 6.000 K1780-42 7/8" 42" 6.000K1102 1/2" 2" 1.250 K1212 5/8" 12" 6.000K1102-1/4 1/2" 2-1/4" 1.250 K1214 5/8" 14" 6.000K1103 1/2" 3" 1.250 K1216 5/8" 16" 6.000 K1302 3/4" 2" 1.375K1104 1/2" 4" 3.000 K1218 5/8" 18" 6.000 K1302-1/2 3/4" 2-1/2" 1.500K1104-1/2 1/2" 4-1/2" 3.000 K1220 5/8" 20" 6.000 K1303 3/4" 3" 1.750K1105 1/2" 5" 3.000 K1222 5/8" 22" 6.000 K1308-1/2 3/4" 8-1/2" 4.000K1106 1/2" 6" 3.000 K1224 5/8" 24" 6.000 K1310 3/4" 10" 4.000K1107 1/2" 7" 3.000 K1226 5/8" 26" 6.000 K1312 3/4" 12" 6.000K1108 1/2" 8" 4.000 K1228 5/8" 28" 6.000 K1314 3/4" 14" 6.000K1109 1/2" 9" 4.000 K1230 5/8" 30" 6.000 K1316 3/4" 16" 6.000K1110 1/2" 10" 4.000 K1230-32 5/8" 32" 6.000 K1318 3/4" 18" 6.000K1112 1/2" 12" 6.000 K1230-34 5/8" 34" 6.000 K1320 3/4" 20" 6.000K1114 1/2" 14" 6.000 K1230-36 5/8" 36" 6.000 K1322 3/4" 22" 6.000K1116 1/2" 16" 6.000 K1230-38 5/8" 38" 6.000 K1324 3/4" 24" 6.000K1118 1/2" 18" 6.000 K1230-40 5/8" 40" 6.000 K1326 3/4" 26" 6.000K1120 1/2" 20" 6.000 K1230-42 5/8" 42" 6.000 K1328 3/4" 28" 6.000K1122 1/2" 22" 6.000 K1230-44 5/8" 44" 6.000 K1330 3/4" 30" 6.000K1122-24 1/2" 24" 6.000 K1230-46 5/8" 46" 6.000 K1332 3/4" 32" 6.000
K1230-48 5/8" 48" 6.000 K1338 3/4" 38" 6.000K1230-50 5/8" 50" 6.000 K1342 3/4" 42" 6.000
K2160 1" 10" 4.000 K1230-52 5/8" 52" 6.000K2162 1" 12" 6.000 K1230-54 5/8" 54" 6.000K2164 1" 14" 6.000K2166 1" 16" 6.000K2168 1" 18" 6.000K2170 1" 20" 6.000K2172 1" 22" 6.000K2174 1" 24" 6.000
SPECIFICATIONS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
10
POLE LINE HARDWARE
HEX BOLTS
K
“K” marking on Head
Ø “A”
“B”
NOTES:1. ASTM A307 AND HOT DIP GALVANIZED TO ASTM SPECIFICATIO A1532. COARSE THREADED TO CLASS 2 FIT3. DOES NOT INCLUDE HEX NUTS OR WASHERS4. THREAD LENGTH: 2*”A”+½”
"A" "B" "A" "B" "A" "B" "A" "B"
(DIA) (L) (DIA) (L) (DIA) (L) (DIA) (L)
K1000-3/4H 3/8" 3/4" K1014-3/4H 5/16" 3/4" K1100H 1/2" 3/4" K1201H 5/8" 1"
K1001H 3/8" 1" K1012-1/4H 5/16" 1-1/4" K1101H 1/2" 1" K1201-1/4H 5/8" 1-1/4"
K1001-1/4H 3/8" 1-1/4" K1013H 5/16" 1-1/2" K1101-1/4H 1/2" 1-1/4" K1201-1/2H 5/8" 1-1/2"
K1001-3/4H 3/8" 1-3/4" K1014H 5/16" 2" K1101-1/2H 1/2" 1-1/2" K1201-3/4H 5/8" 1-3/4"
K1002H 3/8" 2" K1014-1/4H 5/16" 2-1/4" K1102H 1/2" 2" K1202H 5/8" 2"
K1002-1/2H 3/8" 2-1/2" K1014-1/2H 5/16" 2-1/2" K1102-1/4H 1/2" 2-1/4" K1202-1/4H 5/8" 2-1/4"
K1003H 3/8" 3" K1015H 5/16" 3" K1101-3/4H 1/2" 1-3/4" K1202-1/2H 5/8" 2-1/2"
K1003-1/2H 3/8" 3-1/2" K1015-1/2H 5/16" 3-1/2" K1102-1/2H 1/2" 2-1/2" K1203H 5/8" 3"
K1004H 3/8" 4" K1016H 5/16" 4" K1102-3/4H 1/2" 2-3/4" K1203-1/4H 5/8" 3-1/4"
K1004-1/2H 3/8" 4-1/2" K1016-1/2H 5/16" 4-1/2" K1103H 1/2" 3" K1203-1/2H 5/8" 3-1/2"
K1005H 3/8" 5" K1017H 5/16" 5" K1103-1/4H 1/2" 3-1/4" K1204H 5/8" 4"
K1005-1/2H 3/8" 5-1/2' K1017-1/2H 5/16" 5-1/2" K1103-1/2H 1/2" 3-1/2" K1204-1/2H 5/8" 4-1/2"
K1006H 3/8" 6" K1018H 5/16" 6" K1103-3/4H 1/2" 3-3/4" K1205H 5/8" 5"
K1006-1/2H 3/8" 6-1/2" K1018-1/2H 5/16" 6-1/2" K1104H 1/2" 4" K1205-1/2H 5/8" 5-1/2"
K1007H 3/8" 7" K1019H 5/16" 8" K1104-1/2H 1/2" 4-1/2" K1206H 5/8" 6"
K1007-1/2H 3/8" 7-1/2" K1019-1/2H 5/16" 8-1/2" K1105H 1/2" 5" K1206-1/2H 5/8" 6-1/2"
K1008H 3/8" 8" K1020H 5/16" 9" K1105-1/2H 1/2" 5-1/2" K1207H 5/8" 7"
K1008-1/2H 3/8" 8-1/2" K1020-10H 5/16" 10" K1106H 1/2" 6" K1207-1/2H 5/8" 7-1/2"
K1009H 3/8" 9" K1020-10-1/2H 5/16" 10-1/2" K1106-1/2H 1/2" 6-1/2" K1208H 5/8" 8"
K1009-1/2H 3/8" 9-1/2" K1020-11H 5/16" 11" K1107H 1/2" 7" K1208-1/2H 5/8" 8-1/2"
K1010H 3/8" 10" K1020-12H 5/16" 12" K1107-1/2H 1/2" 7-1/2" K1209H 5/8" 9"
K1010-1/2H 3/8" 10-1/2" K1108H 1/2" 8" K1209-1/2H 5/8" 9-1/2"
K1011H 3/8" 11" K1108-1/2H 1/2" 8-1/2" K1210H 5/8" 10"
K1012H 3/8" 12" K1109H 1/2" 9" K1210-1/2H 5/8" 10-1/2"
K1012-13H 3/8" 13" K1109-1/2H 1/2" 9-1/2" K1211H 5/8" 11"
K1012-14H 3/8" 14" K1110H 1/2" 10" K1211-1/2H 5/8" 11-1/2"
K1012-15H 3/8" 15" K1110-1/2H 1/2" 10-1/2" K1212H 5/8" 12"
K1012-16H 3/8" 16" K1111H 1/2" 11" K1213H 5/8" 13"
K1012-17H 3/8" 17" K1111-1/2H 1/2" 11-1/2" K1214H 5/8" 14"
K1012-18H 3/8" 18" K1112H 1/2" 12" K1215H 5/8" 15"
K1113H 1/2" 13" K1216H 5/8" 16"
K1114H 1/2" 14" K1217H 5/8" 17"
K1115H 1/2" 15" K1218H 5/8" 18"
K1118H 1/2" 18" K1220H 5/8" 20"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
1110
POLE LINE HARDWARE
HEX BOLTSHex BoltsASTM A307 and Hot Dip Galvanized ASTM 153.Bolts are Coarse Threaded to a class 2 Fit. Hex Nuts and washers used on these bolts should be ordered separately.Grade 5, silicon bronze, and stainless steel available upon request, please inquire.Custom thread lengths and assemblies are available; please inquire for standard thread length chart.
"A" "B" "A" "B" "A" "B"
(DIA) (L) (DIA) (L) (DIA) (L)
K1300H 3/4" 1" K1702-1/2H 7/8" 2-1/2" K2102H 1" 2"
K1301-1/4H 3/4" 1-1/4" K1704-1/2H 7/8" 4-1/2" K2103H 1" 3"
K1301-1/2H 3/4" 1-1/2" K1705H 7/8" 5" K2103-1/2H 1" 3-1/2"
K1301-3/4H 3/4" 1-3/4" K1706-1/2H 7/8" 6-1/2" K2104H 1" 4"
K1302H 3/4" 2" K1707H 7/8" 7" K2105H 1" 5"
K1302-1/2H 3/4" 2-1/2" K1707-1/2H 7/8" 7-1/2" K2157H 1" 7"
K1302-3/4H 3/4" 2-3/4" K1708-1/2H 7/8" 8-1/2" K2158H 1" 8"
K1303-1/4H 3/4" 3-1/4" K1709H 7/8" 9" K2159H 1" 9"
K1303-1/2H 3/4" 3-1/2" K1709-1/2H 7/8" 9-1/2" K2160H 1" 10"
K1304H 3/4" 4" K1710H 7/8" 10" K2162H 1" 12"
K1304-1/2H 3/4" 4-1/2" K1711H 7/8" 11" K2164H 1" 14"
K1305H 3/4" 5" K1712H 7/8" 12" K2166H 1" 16"
K1305-1/2H 3/4" 5-1/2" K1714H 7/8" 14" K2168H 1" 18"
K1306H 3/4" 6" K1716H 7/8" 16" K2170H 1" 20"
K1306-1/2H 3/4" 6-1/2" K1718H 7/8" 18" K2172H 1" 22"
K1307H 3/4" 7" K2174H 1" 24"
K1307-1/2H 3/4" 7-1/2" K2176H 1" 26"
K1308H 3/4" 8" K2178H 1" 28"
K1308-1/2H 3/4" 8-1/2" K2180H 1" 30"
K1309H 3/4" 9" K2182H 1" 32"
K1309-1/2H 3/4" 9-1/2" K2232H 1-1/2" 5-1/2" K2184H 1" 34"
K1310H 3/4" 10" K2233H 1-1/8" 10" K2186H 1" 36"
K1311H 3/4" 11" K2188-50H 1" 50"
K1312H 3/4" 12" K2188-52H 1" 52"
K1313H 3/4" 13" K2234-2-1/2H 1-1/4" 2-1/2" K2188-54H 1" 54"
K1314H 3/4" 14" K2234-3H 1-1/4" 3" K2188-56H 1" 56"
K1315H 3/4" 15" K2235-1/2H 1-1/4" 14" K2188H 1" 38"
K1316H 3/4" 16" K2190H 1" 40"
K1317H 3/4" 17" K2192H 1" 42"
K1318H 3/4" 18" K2236H 1-1/2" 4" K2194H 1" 44"
K1320H 3/4" 20" K2237H 1-1/2" 5-1/4"
K1322H 3/4" 22" K2238H 1-1/2" 7"
K1324H 3/4" 24"
K1326H 3/4" 26"
K1328H 3/4" 28"
K1332H 3/4" 32"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
12
POLE LINE HARDWARE
CARRIAGE BOLTS
Carriage boltsHot Dip Galvanized ASTM A153Length for a carriage bolt is measured from the under the head to end of the first thread. Threads are Rolled extra long, coarse thread series, class 2 Fit. Equiped with regular cold punched square nut. In the pole line hardware industry, carriage bolts are often used to attach crossarm. Sizes listed are a sampling of active Pole Line Hardware common Carriage Bolts, please inquire for other size requests and carriage bolts assembled with square nuts.STANDARD THREAD LENGTHBolt lengths ≤ 6”: Thread length = (2 X diameter) + 1/4”Bolt lengths > 6”: Thread length = (2 X diameter) + 1/2”Note: Most stock carriage bolts have extended thread length.
B
A3/16"
16 T.P.I.
13/1
6"
¼” LETTER “K” ON HEAD OF BOLT
3/8"
0.188 MIN.0.219 MAX.
TABULATED DIMENSIONS IN INCHES
AB
31 3/4
3 1/21 3/4
41 3/4
4 1/21 3/4
51 3/4
5 1/21 3/4
61 3/4
71 3/4
83
93
103
123
Stock Code Description Long Description Stock CodeDescription Long DescriptionK1003CG BOLT, CGE 3/8" X 3" WITH OUT NUT K1104-1/2CG BOLT, CGE 1/2 X 4-1/2"WITH OUT NUT
K1004CG BOLT, CGE 3/8" X 4" WITH OUT NUT K1104CG BOLT, CGE 1/2" X 4" WITH OUT NUT
K1004-1/2CG BOLT, CGE 3/8" X 4-1/2" WITH OUT NUT K1105CG BOLT, CGE 1/2" X 5" WITH OUT NUT
K1005-1/2CG BOLT, CGE 3/8" X 5-1/2" WITH OUT NUT K1106CG BOLT, CGE 1/2 " X 6" WITH OUT NUT
K1005CG BOLT, CGE 3/8" X 5" WITH OUT NUT K1107CG BOLT, CGE 1/2" X 7" WITH OUT NUT
K1006CG BOLT, CGE 3/8"X6" WITH OUT NUT K1108CG BOLT, CGE 1/2" X 8" WITH OUT NUT
K1012CG BOLT, CGE 3/8" X 12" WITH OUT NUT K1112CG BOLT, CGE 1/2" X 12" WITH OUT NUT
K1014CG BOLT, CGE 3/8" X 14" WITH OUT NUT K1209CG BOLT, CGE 5/8" X 9" WITH OUT NUT
* Also available with Nut upon request. Please inquire, stocked under a separate code.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
1312
POLE LINE HARDWARE
DOUBLE ARMING BOLTS
Double Arming Bolts Kortick Double Arming Bolts are used for mounting hardware on wood structures and to tie cross arms together while maintaining correct spacing. They are equipped with square nuts for pole mounting double cross arms and other hardware items. Lock nuts are recommended for use on end of all bolts to hold the nuts firmly in place under all conditions.Standard DA bolts feature a full threaded bolt, for use between double cross arms. With four nuts, two sandwiching each arm, it can effectively maintain spacing. Bolts are Hot Dip Galvanized for corrosion resistance. Thread is coarse thread to a class 2 fit.Diameter, length (measured from the first thread on each end) and nuts desired are all necessary information to order.
"A" "B" "A" "B" "A" "B"STOCK NO. (DIA) (L) STOCK NO. (DIA) (L) STOCK NO. (DIA) (L)
K1362 5/8" 12" K1382 3/4" 12" K1882 7/8" 22"K1364 5/8" 14" K1384 3/4" 14" K1884 7/8" 24"K1366 5/8" 16" K1386 3/4" 16" K1886 7/8" 26"K1368 5/8" 18" K1388 3/4" 18" K1888 7/8" 28"K1370 5/8" 20" K1390 3/4" 20" K1890-32 7/8" 32"K1372 5/8" 22" K1392 3/4" 22" K1890-34 7/8" 34"K1374 5/8" 24" K1394 3/4" 24" K1890-36 7/8" 36"K1376 5/8" 26" K1396 3/4" 26" K1890-38 7/8" 38"K1378 5/8" 28" K1398 3/4" 28"K1380 5/8" 30" K1400-30 3/4" 30" K2409-18 1" 18"
K1380-32 5/8" 32" K1400-32 3/4" 32" K2409-20 1" 20"K1380-34 5/8" 34" K1400-34 3/4" 34" K2409-22 1" 22"K1380-36 5/8" 36" K1400-36 3/4" 36" K2409-24 1" 24"K1380-38 5/8" 38" K1400-38 3/4" 38" K2409-26 1" 26"K1380-42 5/8" 42" K1400-40 3/4" 40" K2409-28 1" 28"K1380-44 5/8" 44" K1400-42 3/4" 42" K2409-32 1" 32"K1380-48 5/8" 48" K1400-44 3/4" 44" K2409-34 1" 34"K1380-54 5/8" 54" K2409-36 1" 36"
K1872 7/8" 12" K2409-38 1" 38"K1874 7/8" 14"K1876 7/8" 16"K1878 7/8" 18"K1880 7/8" 20"
-ALL D.A. W/ 4 ASSY SQUARENUTS AND CHAMFER TIP-CUSTOM SIZES AVAILABLEUPON REQUEST
“B”
Ø”A”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
14
POLE LINE HARDWARE
DOUBLE ARMING STUD BOLTS
Double Arming Bolts Kortick Double Arming Studs with 6” thread and washer nuts (K2409DE series).They are Hot Dip Galvanized for corrosion resistance. Thread is coarse thread to a class 2 fit.Diameter, length (measured from the first thread on each end) and nuts desired are all necessary information to order.
6"6"
(2 EA) MF LOCKNUTS(2 EA) WASHER NUTS
Ø “A”
“B”
B
A B A C
D EG
F
A 1"BCDE
1 5/8"4 ¼”7/8"7/16"
F 1/8"G 1 7/16"
K2906 Washer Nut Detail
"A" "B"STOCK CODE (DIA.) (LENGTH)K2409-28DE 1" 28"K2409-30DE 1" 30"K2409-32DE 1" 32"K2409-34DE 1" 34"K2409-36DE 1" 36"K2409-38DE 1" 38"K2409-40DE 1" 40"K2409-42DE 1" 42"K2409-44DE 1" 44"K2409-46DE 1" 46"K2409-48DE 1" 48'K2409-50DE 1" 50"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
1514
Kortick Manufacturing and its sign: Hanging tough for 115 years
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
16
POLE LINE HARDWARE
SCREW EYE & THIMBLE EYE SCREWS
Eyes are solid drop forged. Hot Dip galvanized, threads cleaned of excess zincby the Centrifugal Method.
DIAMETER SCREW I.D. EYES
LENGTH UNDER
EYE
3/8" 7/8" x 1-1/4" 3" K2775 221/2" 1-1/4" x 1-1/2" 6" K2776 665/8" 1-1/2" x 2" 6-3/4" K2777 1043/4" 1-1/2" x 2" 6-3/4" K2778 136
DIMENSIONS IN INCHES
STOCK NO.
APPROX. SHIPPING WEIGHT PER 100
PIECES"EEI OVAL EYES"
Eyes are solid drop forged. Hot Dip galvanized, threads cleaned of excess zincby the Centrifugal Method.
DIAMETER SCREW I.D. EYES
LENGTH UNDER
EYE
1/2" 1/2" 6" K2780 665/8" 5/8" 6-3/4" K2781 1143/4" 3/4" 6-3/4" K2782 148
DIMENSIONS IN INCHES
STOCK NO.
APPROX. SHIPPING WEIGHT PER 100
PIECES"THIMBLEYE"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
1716
POLE LINE HARDWARE
LAG SCREWS
Pilot Point
“K” ON HEAD 0.25 HIGH (0.24 MIN THICK)
Dia.
A (Length)
3/8"
K ¾”
5/8"
STANDARD ½” ROLLED FETTER THREADS 6 OR 7 THREADS PER INCH
¼”
Dimensions (Inches)
Stock CodeNo. Diameter
K1682K1683
30"32"
A
4"4-1/2"
Type of Point
PilotPilot
½”½”
K1684 ½” 5" Pilot
60 APPROX.
10 THREADS/INCH
GIMLETPOINT
INDENTED HEADOPTIONAL
¼”
1 ¾” MIN
2 1/2” MIN1/16"
3/16"1
1
K3/8"
.409
5/8"
1 GALV. PER LATEST ASTM SPEC.
K1157 SCREW, LAG THREAD GP, WH ¼” X 2-WASHERHEAD LAG SCREW, GA
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
18
POLE LINE HARDWARE
ADJUSTING SCREW
NAILSPOLE LINE HARDWARE
CURRENT YEARSTAMPED ON HEAD
½”
2 ½”
6GAUGE(13/64)
Stock Code Description
K-200-11 NAIL, POLE DATINGK-200-12 NAIL, POLE DATINGK-200-13 NAIL, POLE DATINGK-200-14 NAIL, POLE DATING
13/32" DIA.
5.00"THREAD¾ - 10 NCROLLEDTHREAD
PITCH DIA.0.675
K1159ADJ SCREW, ADJ RD HOLE, 3/4" GALVANIZEDK1159ADJB SCREW, ADJ RD HOLE, 3/4" BLACK
Adjusting Screws are used in Overhead Switches
5" 5"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
1918
POLE LINE HARDWARE
SQUARE & HEX NUTS
Square and Hex NutsNuts are cold punched, tops are chamfered, bearing surfaces are at right angles to the axis of the threaded hole within a tolerance of 3 degrees for nuts tapped 1-inch and smaller and 2 degrees for nuts tapped larger than 1-inch. Nuts are tapped oversize to accommodate 2-2.5 mils of hot dip galvanizing per ASTM A153 and threads cut to UNC. Nuts are compat-ible with Kortick A307 bolts. Kortick is always willing to use different fastener as-semblies to suit customer requests, please inquire, it is important you specify the application on which the nut is to be used.
STOCK CODENO.
(A)BOLT RODDIAMETER
K1051K1053K1054K1055
1/4"3/8"1/2"5/8"
K1056 3/4"K1057 7/8"K1058 1"
(B) WIDTHACROSS FLAT LENGTH
7/16"5/8"
13/16"1"
28"30"32"34"
1-1/8" 36"1-5/16" 38"1-½” 40"
(C) THICKNESS THREADS PERINCH
7/32"21/64"7/16"35/64"
20"16"13"11"
21/32" 10"49/64" 9"7/8" 8"
DESCRIPTION
NUT, SQ ¼”NUT, SQ 3/8"NUT, SQ ½”NUT, SQ 5/8"NUT, SQ ¾”NUT, SQ 7/8"NUT, SQ 1"
A
C
B
STOCK CODENO.
(A) BOLT RODDIAMETER
K1265K1267K1268K1269
1/4"3/8"1/2"5/8"
K1270 3/4"K1271 7/8"K1272K1273
1"1 1/4"
(B) WIDTHACROSS FLAT LENGTH
7/16"5/8"
13/16"1"
28"30"32"34"
1-1/8" 36"1-5/16" 38"1-½”1-7/8"
40"42"
(C)THICKNESS THREADS PERINCH
7/32"21/64"7/16"35/64"
20"16"13"11"
21/32" 10"49/64" 9"7/8"
1-3/32"8"7"
DESCRIPTION
NUT, HEX ¼”NUT, HEX 3/8"NUT, HEX ½”NUT, HEX 5/8"NUT, HEX ¾”NUT, HEX 7/8"NUT, HEX 1"
NUT, HEX 1- ¼”
A
B
C
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
20
POLE LINE HARDWARE
M-F NUTSM-F NutsKortick M-F lock nuts are a free spinning lock nut that starts from either side and spins into place with the fingers. One half to a full turn with a wrench locks it securely. When the arched surface contacts the top of the nut, wrenching flattens the arch, deflecting the nut threads from their true helix and causing them to bind on the bolt. M-F nuts are vibration proof and Hot Dip Galvanized per ASTM A153.
OVERALL CENTERSTOCK NO. BOLT DIA. WIDTH THICKNESS THICKNESS
"A" "B" "C" "D"K1065 3/8" 5/8" 1/4"K1066 1/2" 13/16" 19/64"K1067 5/8" 1" 3/8" 3/16"K1068 3/4" 1-1/8" 7/16"K1069 7/8" 1-5/16" 15/32" 3/16"K1070 1" 1-1/2" 15/32" 3/16"
DIMENSIONS, INCHES
“A”
“B” “C”
“D”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
2120 Thermal Diffusion GalvanizingBeginning early 2013Kortick is proud to offer thermal diffusion Galvanizing as a compliment to Hot Dip Galvanizing. “TDG” is a process that bakes the propirietary solution into the steel. TDG has superior corrosion performance as tested in the dead sea and on navy chain. The solu-tion bonds to become part of the steel, not just a superficial coating. The non toxic substance is weldable for post production field modifications and embedded in the steel to allow for grinding with minimal loss in corrosion resistance. The process combines superior protection with an environmentally friendly process .TDG meets A123 and A153 while also adhering to a more stringent spec written with TDG in mind, A1059.TDG won the 2006 EPA award for “most valuable pollution prevention” (MVP2)
For more information about TDG please contact sales@Kortick.com
HDG TDG
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
22
POLE LINE HARDWARE
ROUND WASHERSRound WasherRound washers are installed under the heads, nuts, and eyes of bolts, rods, or other threaded products to provide a broader bearing surface and increase the compression grip of a tightened nut.
LOCK WASHERSLock WashersLock washers are designed to prevent a Bolt or a screw from turning or spinning due to vibration. Made from high grade spring steel
½”5/8"
3/8"A. BOLT DIAMETERSTOCK CODE No
K1254K1255K1256K1257 ¾”
A
K1258
K1259
7/8"
1"
.125
.156
.094THICKNESS
.234 .188
.266
.297
.219
.250
WIDTH.141.171.203
Monday, April 16, 2012
5/16"3/8"
¼”
A. BOLT RODDIAMETERSTOCK CODE No
K1521K1521-1/2
K1522*K1523 3/8"
K1524
K1525
½”
5/8"
-7/16
5/16Hole
1 1/4 1/2
1 3/8
1 3/4
9/16
11/16
Outside3/4-1
K1526 ¾”K1527
K1528
7/8"
1"
2 13/16
2 1/4
2 1/2
15/16
1-1/16
K1528-1 3/4 1 ¾” - -
DIAMETER THICKNESS
-14
16B.W.G.
5/64 14
7/64
9/64
12
10
5/32 9
11/64
11/64
8
8
- -
Inch1/16
-5/64
DIMENSIONS, INCHES
*WASHER, ROUND 3/8" ONLY UNDER HEAD OF CG BOLT
Wednesday, July 25, 2012
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
2322
POLE LINE HARDWARE
DOUBLE COIL LOCK WASHERDouble Coil Lock Washer Double Coil Lock Washers are made of spring steel for keeping the bolt or screw in tension.
MALLEABLE IRON ROUND WASHERMalleable Round WashersMalleable iron round washers used with poles and other wood solutions, most notably the marine industry.
2 ¾”
5/16"
5/8" BOLT SIZE DIAMETER
K1525MI WASHER, MALLEABLE IRON 5/8"
½”5/8"
3/8"A. BOLT DIAMETERSTOCK CODE No
K1254DC
K1255DC
K1256DC
K1257DC ¾”
A
3/16"
Monday, April 16, 2012
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
24
POLE LINE HARDWARE
SQUARE WASHERSquare WasherInstalled under the heads, nuts, and eyes of bolts, rods, or other threaded products to provide a broader bearing surface and increase the compression grip of the tightened nut. They prevent the crushing of wood fibers and protect the drilled hole. Square washers also allow for alignment checking.
SQUARE CURVED WASHERSquare Curved Washer The square curved washer has the same function as the square flat washer except bent at a 4 ½ radius to fit the contour of the pole. Square curved washer, at the proper thickness, can be used to replace heavy cast washers.
A a
D b
B a
C b
4 ½” RAD.
STOCK CODEK1582K1590K1591K1592K1594K1596K1597
K1597 1/4
A3"
2 ¼”2 ½”
B3"
2 ¼”2 ½”
3" 3"3 ¼” 3 ¼”3 ½”4"6"
3 ½”4"6"
C¼”
3/16"3/16
D11/16"11/16"11/16"
¼” 13/16"¼” 13/16"
3/8"¼”3/8"
1 1/8"15/16"1-3/16"
DIMENSIONS IN INCHES
ab
1/16"1/32"
ALLOWABLEVARIATION
1/16"1/32"
*COMPLIES WITH EEI-NEMA STANDARD PH 10
BOLT ROAD DIAMETER STOCK CODE NO.
1/25/8
1/2 - 5/83/4
K1550K1551K1570K1553
5/8 – 3/4 K15545/8 – 3/4 K1557¾ -7/8
11
1-1/4
K1558K1559K1561K1562
WIDTH HEIGHT
22
2 1/42 1/4
22
2 1/42 1/4
3 34 44466
4466
DIMENSIONS IN INCHESSQUARE
THICK-NESS HOLE INSIDEDIAMETER
1/81/83/163/16
9/1611/1611/1613/16
3/16 13/163/16 13/161/43/83/81/2
15/161-1/8
1-3/161-3/8
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
2524
POLE LINE HARDWARE
SQUARE CURVED HEAVY CAST WASHER
LIP WASHERLip WashersKortick threaded lip washers, also referred to as a flange washer, are used on cross arm pins to provide a permanent connection for the bonding wire.
Square Curved Washer Heavy CastSquare cast heavy curved washers are designed with reinforced ridges for additional strength in the critical areas. Reinforced bolt hole furthers the strength of a heavy cast washer. Heavy cast washers can be replaced by standard square forged washers of the proper thickness. Please inquire for forged substitute part numbers
K1597HC
4"
Ø 7/8" THRU HOLEDEPTH OF ¼”
Ø 1 9/16" HOLE TO
¾” RADIUS
3/8"
¼”
1/8" THICK
A
A
3"
3"
SECTION A-A
5/16"
1-3/8" DIA
BOLTHOLE
STOCK CODE BOLT DIAMETERK1582HC 5/8"K1592HC 3/4"
E
DBOLT HOLEDIAMETER
C
B
A
5/8"
STOCK BOLT CODE DIAMETER A B C D EK1645 5/8" 2 3/16 2 3/16 1 3/16 1K1646 3/4" 3 3 1/4 1 1/2 1 1/2
DIMENSION, INCHES
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
26
POLE LINE HARDWARE
SPRING CLIP WASHERSpring Clip WashersKortick spring washer, also referred to as static washers, are installed under the nut of a bolt and next to the cross arm to keep units in tension when shrinkage in wood occurs. Also used for alignment checking.
BEVEL WASHERBevel Washer Drop forged steel Bevel washers are used for channels and flanges to bring to parallel.
5/8"½”
BOLT DIAMETERSTOCK CODE No
K1547-1/2
K1547-5/8
D
A
C
B
A
1 ¼”1 ½”
B
11/32"13/32"
C
5/32"5/32"
D
9/16"11/16"
7/16" R. 45
X
Y
E
D
B C
A
STOCKCODE NO. SIZE
K2908K2909K2910
K2910-1/2
1/25/83/4-
D E
9/1611/1613/16
-
11/1613/16
1-
DIMENSIONS IN INCHESSIZE OF SLOT
F + 11/16- 0 G
3/165/165/16
-
9/1611/1613/16
-
X Y
SIZE OFSTEEL
5/32 1
1/4 1 3/4
1/4 1 3/4
- -
A B
3 1/2
3 1/2
-
C
2 5/8
2 9/16
2 9/16
-
1 15/16
15/16
15/16
-
11/16
H + 1/16
9/1611/1611/16
-
x
H
G dia.
F
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
2726
POLE LINE HARDWARE
CENTERING WASHER
ANGLE PIN WASHERAngle Pin WashersAngle Pin Washers are notched for nail to prevent turning.
Centering WashersKortick centering washers, sometimes called pin hole adapters, are used to center the shanks of forged steel insulator pins in cross arms, prevent worn holes, and adapt ¾ wood hole to a 5/8 pin.
PAD MOUNTED TRANSFORMER HOLDDOWN WASHER
2"
9/16" SLOTHOLE
5"
3/16"
KXFMRWASHER PAD MOUNTED TRANSFORMER LIP HOLD DOWN WASHER
3½” 1¾”
1¾”
1 ¾” 1 ¾”
13/16"HOLE
3 ½”
¼”
¼”
3/8"
K1615 WASHER, ANGLE PIN
C (DIA.)
5/8" b
B Dia.A Dia.
6666
2 ¾”13/16"1 ½”K16322-¾”11/16"1-½”K1630
CBAStock Number
DIMENSIONS IN INCHES
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
28
POLE LINE HARDWARE
SHEAR PLATESShear plates are used to create a firm seat in the pole or cross arm for wood-to-wood joint or wood to steel connections. Shear plate provides reinforcement to the bolt by increasing the web capacity to resist shearing loads.
FRONT VIEW
TOP VIEW
SIDE VIEW
Ø 2-5/8"
DIA 13/16"
5/32 HOLE
2-5/8"
5/32" HOLE
STOCK CODE NoK8295K8298K8299
7/8" 4"1"
¾”A. BOLT DIAMETER B. OUTSIDE DIAMETER
4"
4"
A
B
Monday, April 09, 2012
SHEAR PLATES
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
2928
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
30
POLE LINE HARDWARE
Shoulder eyebolts provide ample bearing surface, which eliminates the use of washers under the eye. They are used for hanging suspension hardware to the pole or cross arm. Kortick’s primary shoulder eye is rare in the industry with a forged shoulder surface. The one-piece shoulder eye is known for exceptional strength and durability. Shoulder eyebolts are also available in different diameter shoulders. Please inquire for customization requests.Welded washer style also available, flat (not pictured) and curved (pictured on next page).
FORGED SHOULDER EYE BOLTS
¾211/163-⅛¾⅝1-¾9/162-⅞⅝DCBA
DIMENSIONS, INCHES
K2566 6 16146K2564126K2562106K256086K255864K2556
Bolt LengthThread Length5/8 Diam
206K2570186K2568
K2586 6 16146K2584126K2582106K258086K257864K2576
Bolt LengthThread Length¾ Diam
206K2590186K2588
1 ¾” Dia.D
Sq. Nut
B
A
C
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
3130
POLELINE HARDWARE
CURVED WELDED SHOULDER EYEBOLTS
Bolt Dia. Sq. Nut
LT
K2588CW 18 6616K2586CW414K2584CW412K2582CW410K2580CW38K2578CW
Thread Length (T)Length (L)Stock Number
¾” Bolt Diameter(Inches)
830K2590-30CW628K2590-28CW626K2590-26CW624K2590-24CW622K2590-22CW620K2590CW
620K2598CW618K2597CW616K2596CW614K2595-14CW612K2595-12CW
Thread Length (T)Length (L)Stock Number
⅞” Bolt Diameter(Inches)
Stock Code Length (L) Thread Length (T)K2556CW 6 6K2558CW 8 6K2560CW 10 6K2562CW 12 6K2564CW 14 6K2566CW 16 6K2568CW 18 6K2570CW 20 6K2572CW 22 6K2574CW 24 6K2576CW 26 6
K2576-28CW 28 8K2576-30CW 30 8
5/8" Bolt Diameter (Inches)
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
32
POLE LINE HARDWARE
OVAL EYE BOLTSOVAL EYE BOLTSKortick Oval Eye Bolts are used for guying, dead ending and attaching clevises. Oval Eye Bolts are also used in the case of specialty needs of suspension insulators and pole line hardware. All oval eyes are hot forged from A36 steel, galvanized to ASTM A153, and assembled with standard square nut. K2640 (not pictured) Oval eye bolt is specifically used in conjunction with Kortick under-ground ladders.*Custom sizes and assemblies are available upon request
C
B DE Length
2 1/421½⅝¾221½9/16⅝
1 3/41 ½1¼7/16½EDCBA
K2685 6 16146K2684126K2682106K268186K268064K2678
Bolt Length Under EyeLength5/8 Diam
K2689-30 6 30286K2689-28266K2689-26246K2689226K2688206K2687186K2686
K2664 6 16146K2662126K2660106K265886K265664K2654
Bolt Length Under EyeLength½ Diam
206K2668186K2666
K2707 6 16146K2706126K2705106K270486K270364K2702
Bolt Length Under EyeLength¾ Diam
246K2711226K2710206K2709186K2708
Dimensions, InchesA
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
3332
POLE LINE HARDWARE
DOUBLE ARMING OVAL EYE BOLTS
Kortick Full Thread Oval Eye Bolts and Nuts are used for guying, dead ending, as an attaching unit for clevises, suspension insulators and pole line hardware and specialty items. Equipped with regular Cold Punched Square Nut.
C
L
Kortick Full Thread Oval Eye Bolts And Nuts are used for guying, dead-ending,as an attaching unit for clevises, suspension insulators and poleline hardware
and specialty items. Equipped with Regular Cold Punched Square Nut.
Double Arming Oval Eye BoltsDimensions, Inches
A
1 ½”Drop Forged Eye
Stock Code A C LK2601 5/8" 1-1/2" 12"
K2602 5/8" 1-1/2" 14"
K2603 5/8" 1-1/2" 16"
K2604 5/8" 1-1/2" 18"
K2605 5/8" 1-1/2" 20"
K2606 5/8" 1-1/2" 22"
K2607 5/8" 1-1/2" 24"
K2608 5/8" 1-1/2" 26"
K2609 5/8" 1-1/2" 28"
Stock Code A C LK2614 3/4" 1-1/2" 12"
K2615 3/4" 1-1/2" 14"
K2616 3/4" 1-1/2" 16"
K2617 3/4" 1-1/2" 18"
K2618 3/4" 1-1/2" 20"
K2619 3/4" 1-1/2" 22"
K2620 3/4" 1-1/2" 24"
K2621 3/4" 1-1/2" 26"
A C5/8 1 1/23/4 1 1/2
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
34
POLE LINE HARDWARE
Attaching Eye Nuts and EyeletsKortick Standard Eye Nuts are used for hanging suspension type insulators or other hardware from the cross arm.Kortick Standard Long Eye Type is also used as an attaching unit on the cross arm for hanging suspension insulator strings when the upper unit is equipped with a clevis type or hook type cap.
EYE NUTS & EYELETS
E
C
D
B
FA
21,000½”2-½”1-¾”14,500½”2-½”1-¾”8,500½”2-⅛”1-⅛”
Max. Load (lbs)FED
¾”1-¾”1-½”¾”K4213¾”1-¾”1-½”⅝”K4212
11/16"1-⅛”1-⅛”½”K4210CBADiameter BoltStock Number
DC
B
D
A
F
E
D2-¼2-¼2-¼2-¼⅜3
⅜3⅜2-⅜⅜2-⅜CBA
1-¼1-¼1-¼1-¼1-⅛13/1621,000¾K4414
111/1614,500⅝K44131-⅛13/1621,000¾K4412
111/1614,500⅝K4411FEMax Load
(lbs)Bolt Dia.Stock Number
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
3534
POLE LINE HARDWARE
THIMBLE EYES & EYE NUTS
Thimble Eyes and Eye NutsKortick Eyelets (Bolt Eyes) are universally used for dead ending, guying, and as an attaching unit on the cross arm for hanging hardware. Eyes are mounted to the pole or cross arm under either the square head or nut of a cross arm or double arming bolt, or under the nut end of an eyebolt. The bottom slot or hole is elongated to provide sufficient clearance to insert the bolt at any angle. Designed to develop greater strength than the bolts to which they are attached.
Hot dip galvanized after fabrication per latest revision ASTM Spec. A153Kortick Thimble Eyelets are fabricated with the wire grooves contoured to prevent the strand bending or kinking under tension. The Straight Type is used for span or messenger guy attachments. The Angle Type is used for down guy attachments.Kortick Eye Nuts are used to add Eyes to installations for dead ending, stub or head guying. The Eye Nut develops greater strength than the rods to which they are attached. Hot dip galvanized per latest revision ASTM Spec. A153. Excess zinc removed by the Centrifugal Method. Tapped Coarse Thread Series, Class 2 Fit.
Kortick Thimble-Eyenuts prevent the strand bending and kinking under tension. Thimbleyes are used for one-strand guying, Twineyes for two-strand guying, Triple Eye for three-stand guying.
R9/329/32
B
F
A E
C
D
¼R
ED
K3131 Straight
F4-5/16
4-5/162-1/162-9/161-5/161-½2-1/162-9/161-5/161-½
EDCBA2-1/16
2-1/1621,000½3/16 x 1-⅛¾”K313114,500½11/16 x 1⅝”K3130
MaximumLoad (lbs)
Guy StrandCapacity
MountingBolt Hole
DiameterBolt-RodStock Number
G2-½2-½2-½1-⅝13/16
11/16
2-½1-⅝13/1611/16
FEDCB
1-½1-½13/1621,000½¾”K3141
11/1614,500½⅝”K3140Hole AMaximum
Load (lbs)
GuyStrand
Capacity
DiameterBolt-RodStock Number
Straight “Thimbleye”
Angled “Thimbleye’
K3140 Angle
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
36
POLE LINE HARDWARE
THIMBLE EYES & EYE NUTS
BE
R R
FD
CA
AE
DC
RF
K3112 “THIMBLEYE” K3121 “TWINEYE”
B
1.2
1.75
1.85
1.6
1-8 UNC-2B
K3127 Triple Eye Nut
K
BOLT OR ROD DRILL AND GUY STAND MAX. LOADSTOCK No. DIAMETER TAP CAP MAX. DIA (LBS) A B C D E F R
K3110 1/2" 33/64-13 thread 7/16" 8,500 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3-1/4" 1/4"K3111 5/8" 41/64-11 thread 7/16" 14,500 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3-1/4" 1/4"K3112 3/4" 49-64-10 thread 7/16" 21,000 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3-1/4" 1/4"K3113 1" 1-1/64- 8 thread 5/8" 42,000 1-3/4" 1-5/8" 1-1/4" 1-5/8" 2-1/4" 3-7/8" 13/32"
K3120 5/8" 41/64-11 thread 1/2" 14,500 1-7/8" 1-1/2" 1-5/16" 2-1/8" 4-3/32" 1/4" 1/4"K3121 3/4" 49-64-10 thread 1/2" 21,000 1-7/8" 1-1/2" 1-5/16" 2-1/8" 4-3/32" 1/4" 1/4"K3122 1" 1-1/64- 8 thread 1/2" 42,000 1-7/8" 1-1/2" 1-5/16" 2-1/8" 4-3/32" 1/4" 1/4"
"THIMBLEYE"
"TWINEYE"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
3736
POLE LINE HARDWARE
PISA RODS
Guy Hooks:
Cast Guy hooks available for 5/8 and 3/4 bolts.Used for down guy applications
Power Installed Screw Anchor Rod for use with power installed screw anchors.
THREAD1-8UNC-2A
1.00"DIA
1.00" HEXJAM NUT
L
THREADON BOTH
ENDS
1"
1. HOT DIP GALV PER ASTM 153, AFTER FABRICATION
2. GRADE A36 STEEL WITH 36,000 PSI TENSLE STRENGTH
PART NO. “L” DIA.KA11200 3-½’ 1"KA11210 7' 1"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
38
POLE LINE HARDWARE
THIMBLE EYE BOLTSThimbleye BoltsKortick Thimbleye bolts and nuts are universally used for attaching guys to poles and cross arms, for dead-ending and for down guying. Forged in two styles, STRAIGHT type and 45-degree ANGLE or BENT type. Fabricated with the “THIMBLEYE” drop forged on the bolt, eliminating the use of separate guy thimble. Eyes (detailed below) develop greater strength than the bolt itself.Threads are CUT 6 inches long, Course Thread Series, Class 2 Fit before galvanizing. Equipped with one Regular Cold Punched Square Nut. Hot dip galvanized, per latest revision ASTM Spec A153, threads cleaned of excess zinc by the Centrifugal Method. Nuts are tapped after galvanizing, and when assembled ensure a perfect “finger fit.”We recommend curved washers be placed under the nuts with guy or lift plates under the eyes to distribute the load strain set up by the guys over a greater surface area. Square Washers and Curved Washers and Guy or Lift Plates used with these eye bolts are extra, and should be specified and ordered separately. See Plates section of catalog.
KOR
TICK
KOR
TICK
K3238Straight Type
⅝-Inch Diameter BoltsMinimum Breaking Strength, Thread Section, 12,500 Pounds
¾-Inch Diameter BoltsMinimum Breaking Strength, Thread Section, 19,000 Pounds
K3254Bent Type
Stock CodeDescriptionK3215 BOLT, ST THIMBLEYE 5/8" X 8"
K3216 BOLT, ST THIMBLEYE 5/8" X 10"
K3217 BOLT, ST THIMBLEYE 5/8" X 12"
K3218 BOLT, ST THIMBLEYE 5/8" X 14"
K3220 BOLT, ST THIMBLEYE 5/8" X 16"
K3222 BOLT, ST THIMBLEYE 5/8" X 22"
K3222-24 BOLT, ST THIMBLEYE 5/8" X 24"
K3222-26 BOLT, ST THIMBLEYE 5/8" X 26"
K3222-28 BOLT, ST THIMBLEYE 5/8" X 28"
K3222-30 BOLT, ST THIMBLEYE 5/8" X 30"
K3235 BOLT, ST THIMBLEYE 3/4" X 8"
K3236 BOLT, ST THIMBLEYE 3/4" X 10"
K3237 BOLT, ST THIMBLEYE 3/4" X 12"
K3238 BOLT, ST THIMBLEYE 3/4" X 14"
K3240 BOLT, ST THIMBLEYE 3/4" X 16"
K3241 BOLT, ST THIMBLEYE 3/4" X 18"
K3242 BOLT, ST THIMBLEYE 3/4" X 20"
K3248 BOLT, ST THIMBLEYE 1" X 14"
K3249 BOLT, ST THIMBLEYE 1" X 16"
K3250 BOLT, ST THIMBLEYE 1" X 18"
* 6" STANDARD THREAD
Stock Code DescriptionK3254 BOLT, BENT THIMBLEYE 5/8" X6"(4" THREAD)
K3255 BOLT, BENT THIMBLEYE 5/8" X8"
K3256 BOLT, BENT THIMBLEYE 5/8" X10"
K3257 BOLT, BENT THIMBLEYE 5/8" X 12
K3258 BOLT, BENT THIMBLEYE 5/8" X14"
K3260 BOLT, BENT THIMBLEYE 5/8" X16"
K3262 BOLT, BENT THIMBLEYE 5/8" X20"
K3264 BOLT, BENT THIMBLEYE5/8" X24"
K3275 BOLT, BENT THIMBLEYE, 3/4"X8"
K3276 BOLT, BENT THIMBLEYE, 3/4"X10"
K3277 BOLT, BENT THIMBLEYE, 3/4"X12"
K3278 BOLT, BENT THIMBLEYE, 3/4"X14"
K3280 BOLT, BENT THIMBLEYE, 3/4"X16"
K3281 BOLT, BENT THIMBLEYE, 3/4"X18"
K3282 BOLT, BENT THIMBLEYE 3/4"X 20"
* 6" STANDARD THREAD
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
3938
POLE LINE HARDWARE
LOAD AND LIFT GUY PLATES
Size Oval holeDiameterMounting Holes
Fit DiameterEyeboltPlate ThicknessStock Number
K3523
9"
11/16" Dia.9/16" Dia.
1⅜”2½”
5/16"
6-¾”
4-7/8"
1-¼”
?
1¼” Dia.
K3503
9/16"Dia.
11/16"Dia.
4"2"
1-3/8" 1-3/8" 5/16"
3-¾”4-¾”
7"
1-¼” Dia.
KORTICK LOAD AND LIFT GUY PLATES are used behind the eyes of Angle“Thimbleye” bolts to increase their load capacity. The elongated hole is shapedso the base of the “Thimbleye” fits INTO it, adding support or “lift” to the eyebolt.
Plates distribute the load in tension over a greater surface area and reinforce thewood fibers of a pole against shear resulting from excessive down pull.
1-1/16 x 1-1/411/165/81/4K3501
Size Oval holeDiameterMounting Holes
Fit DiameterEyeboltPlate ThicknessStock Number
13/16 x 1-1/169/163/41/4K3506
Size Oval holeDiameterMounting Holes
Fit DiameterEyeboltPlate ThicknessStock Number
1-1/8 x 1-7/169/1615/16K351213/16 x 1-1/169/163/41/4K351113/16 x 1-1/169/163/43/16K35141-1/16 x 15/169/165/83/16K3510
Size Oval holeDiameterMounting Holes
Fit DiameterEyeboltPlate ThicknessStock Number
K3518 5/16 1 9/16 1-1/16 x 1-5/1613/16 x 1-1/169/163/45/16K352213/16 x 1-1/169/163/41/4K351713/16 x 1-1/169/165/83/16K352111/16 x 15/169/165/85/16K352011/16 x 15/169/165/81/4K3519
11/16 x 15/169/165/83/16K3516
1-1/411/161 & Under5/16K35241-1/411/161 & Under5/16K3523
Size Oval holeDiameterMounting Holes
Fit DiameterEyeboltPlate ThicknessStock Number
Flat 3 Hole Plates – 2-½ Inches Wide by 7 Inches Long
Curved Plates – 2-½ Inches Wide by 7 Inches Longfor Guy and Straight-Away Loops
Curved 2 Hole Plates – 2-½ Inches Wide by 7 Inches Long
Curved 3 Hole Plates – 2-½ Inches Wide by 7 Inches Long
Flat 4 Hole Plates – 2-½ Inches Wide by 9" Inches Long
1-1/4 ...11/161 & Under5/16K35041-1/4 ...11/161 & Under5/16K3503
Size Oval holeDiameterMounting Holes
Fit DiameterEyeboltPlate ThicknessStock Number
Flat 4 Hole Lip Plates – 4 Inches Wide by 7 Inches Long
Fabricated from steel.Hot dip galvanized.
CURVED SQUAREWASHERS arerecommended for useunder the nut of theguy fitting inconjunction with the liftplates.
1/16"RAD
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
40Sidewalk Guy FittingsKortick Sidewalk Guy Arm Pipe fittings are used where fixed length arms are impractical. Attaching the fittings to the unthreaded ends of any length stan-dard pipe completes a guy arm unit to extend across any width sidewalk or right of way where head room must be maintained. Assembled with regular square head machine bolts and square nuts, fittings are hot dip galvanized. Field drawing for reference only, pipe and other guying hardware not included.
POLE LINE HARDWARE
SIDEWALK GUY FITTINGSNew Positionof Set Screw
3 11/16"
3 3/8"
K6275 WITH BUSHINGFOR 2.0" PIPE
2 1/8"
K6277 WITH OUTBUSHINGFOR 2.5" PIPE
New Three wire design.Can accommodate 1,2,3wires.
Pipe section View:
Length to SuitConditions (pipe
not included)
K6276, K6278Pole Plate
K6275, k6277Sidewalk Guy
Clamp EndFitting
Heightto
Suit
Conditions
Stock Code Description I.D. Pipe DiamK6275 GUY CLAMP PIPE SOCKET 2K6276 POLE PLATE PIPE SOCKET 2K6277 GUY CLAMP PIPE SOCKET 2.5K6278 POLE PLATE PIPE SOCKET 2.5
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
4140 GUY HOOKSPOLE LINE HARDWARE
2"
2.1"
Ø0.7"
Ø0.90"
STOCK CODE DESCRIPTIONKA11900 ¾” GUY HOOK
R 0.4"
0.9"
3.156"
STOCK CODE DESCRIPTIONKA11875 5/8" GUY HOOK
Guy Hooks:
Cast Guy hooks available for 5/8 and 3/4 bolts.Used for down guy applications
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
42
POLE LINE HARDWARE
POLE EYE PLATEPole Eye PlatesKortick Heavy Pole Eye Plates are through welded for heavy duty applications. Available in flat and round base-Please inquire for custom design and part numbers.
¾”
5/16" SEAL/WELD
15/16" DIA
11 5/8"
¾”
½”
5/16" SEAL/WELD
15/16" DIA
2 ¾”
8 " 3-½”
*THROUGH WELDED FOR AN ULTIMATE STRENGTH OF 75,000 LBS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
4342 DEAD END TEEDead End TeeRegular Duty Dead end tee. Multiple Tee designs are available; please inquire for part numbers, designs, and strengths.
POLE LINE HARDWARE
11 5/8"
3 ½”
1 ¾”
1 5/16" 9" 1 5/16"
4"
45
1 1/8" holes(3 places)
½”
SEAWELD
SPECIFICATIONS:1)Material: Steel A-36. 40,000Pull Test2)Finish: Hot Dip Galvanize perASTM A-153
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
44
POLELINE HARDWARE
Kortick Single and Double cup pole bands Kortick Single and Double cup pole bands (K8183 series) supply additional attaching points for pole line hardware items, specialty items, and for dead end or guying lines.
SINGLE AND DOUBLE CUP BANDS
POLERANGE
⅝” MOUNTING BOLT ⅝” MOUNTING BOLT
¼” BAND SEGMENT
* SINGLE CUP BANDS are equipped with ONE ⅝” MOUNTING BOLT* DOUBLE CUP BANDS are equipped with TWO ⅝” MOUNTING BOLT
Stock Code Description Pole (O.D.) RangeK8183 BAND, POLE 3-1/2"-4" SINGLE CUP 3.5-4"K8184 BAND, POLE 4-5" SINGLE CUP 4-5"K8185 BAND, POLE 5"- 5-1/2" SINGLE CUP 5-5.5"
K8193 BAND, POLE 3-1/2-4" DOUBLE CUP 3.5-4"K8194 BAND, POLE 4-5" DOUBLE CUP 4-5"K8195 BAND, POLE 5-15/12 DOUBLE CUP 5-5.5"
½”x 3", 4-½”, 5"GALVANIZED
MACHINE BOLTx2
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
4544Three Piece Round Bar Pole BandsKortick Three piece Round bar pole bands (K8193 series) for steel poles. Round bar design limits corrosion on the steel pole. Three-piece design displaces load across from eye to eye of opposing band section, taking load away from fastener. These bands are popular with light rail, electric bus, and other municipality uses on the west coast.
POLELINE HARDWARE
THREE PIECE POLE BAND
Stock Code Description Material CUT LENGTHK8196 BAND, POLE #1 3 PC 3/4" 12-5/8"K8197 BAND, POLE #2 3 PC 3/4" 14-1/2"K8198 BAND, POLE #3 PC 3/4" 15-1/2"K8199 BAND, POLE #4 3 PC 3/4" 17"K8200 BAND, POLE #5 3 PC 3/4"K8202 BAND, POLE #7 3PC 1"K8203 BAND, POLE SPL 3 PC 3/4"K8204 BAND, POLE SPL 3 PC 1"K8204-3/4 BAND, POLE SPL 3 PC 3/4"K8205 BAND, POLE SPL 3 PC 1"* All Bolts and Nuts Per ASTM A325Hot Dipped Galvanized
10-11.25"11-12.25"
Pole (O.D.) Range4.5-5.5"6-7.25"7-8.25"8-9.25"9-10.25"9-10.25"
10-11.25"10-11.25"
11"
1 ¾”
ؾ”
Ø1 ¾”
BOLT, LOCKWASHER
AND NUT x3
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
46FOUR WAY POLE BANDPOLELINE HARDWARE
POLERANGE8"-12"
7/8" ALL THREAD ROD(4)
7/8" NUT (16)
9/16" SQUARE HOLEFOR ½” LAG SCREW (2)
NOTE:1. ALL PARTS GALVANIZED2. SECTIONS ARE MADE OF ½”x4" STEEL3. NUTS ARE INCLUDED4. 7/8"x3" CARRIAGE BOLT AND NUT INCLUDED5. LAG SCREW NOT INCLUDED
15/16" HOLE x8
15/16" SQUARE HOLE FOR7/8" CARRIAGE BOLT (2)
K5071 WITH A STUD BOLTK5072 WITH 2 STUD BOLTS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
4746 AWARDS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
48
POLE LINE HARDWARE
STUBBING BANDS & PIPE
Stubbing Bands and PipeKortick stubbing reinforcing bands and fittings add years of life to a pole with a rotted, weakened butt. To use, set a correct length stub, approximately the same diameter and ground depth as the pole, and securely bind stub and pole above the ground line at two or more points, selecting and using the stubbing combination best adapted. Tighten by inserting through bolt into one slotted hole of the band and engage one of the holes on the opposite side. Tighten the nut and the bands are drawn into the pockets between the pole and stub with the stubbing pipe in place. **Please inquire about custom length and hole dimensions.
K4312
¼” NAIL HOLE
47-½”(9/16" HOLES @ 2")
K4310LENGTH= 69-1/2"; WIDTH=2"; THICKNESS=1/8"
3-¾”1-¼"
ThroughBolt
K4312Pipe
K4307-K4311Bands
STOCK BOLT HEIGHT OF CODE TYPE THICKNESS WIDTH LENGTH HOLE POLE (FT)K4307 BAND 12 B.W.G. 2" 96" 11/16" 50K4309 BAND 12 B.W.G. 2" 120" 9/16" 50 or OVERK4310 BAND 12 B.W.G. 2" 68-1/2" 9/16" 40 or LESSK4311 BAND 12 B.W.G. 2" 89-1/2' 9/16" 40 or LESSK4328 BAND 12 B.W.G. 2" 76-1/2" 9/16" 40 or LESSK4312 PIPE 2 EXTRA HEAVY 5" 3/4" ALL
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
4948
POLE LINE HARDWARE
STUBBING BANDS
1”1¼”
17 @ 2" = 2'-8" 4-3/4" 1¼”
11/16"11/16"HOLES K4307:
LENGTH= 96"; WIDTH = 2”; THICKNESS= 1/8"
7/16"
¼” NailHole
K4310LENGTH=68-½”; WIDTH= 2"; THICKNESS=1/8"
1-¼"
39" (9/16" HOLES @2" x20)
K4328LENGTH=76-½”; WIDTH= 2"; THICKNESS=1/8"
¼” NAIL HOLE
1-¼"
1-¼"
3-¾”
¼” NAIL HOLE
47-½”(9/16" HOLES @ 2")
K4309LENGTH= 120"; WIDTH=2"; THICKNESS=1/8"
3-¾”1-¼"
¼” NAIL HOLE
33" (9/16" HOLES @2" x17)
3-¾”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
50
POLE LINE HARDWARE
POLE STEPS FOR WOOD POLES
Pole Steps for Wood PolesKortick wood pole steps are driven into wood poles to provide secure foot and hand holds for climbing. Typically, pole steps start no less than 8 feet above the ground and are spaced 18” apart on alternate sides of the pole. They are generally located in line with the lead in the same vertical plane. Kortick manufactures several types of pole steps and its unique features make it the favored step of lineman. The K4252 Pole step for wood poles has a “handy drive” head, wide, strong in the cross section, and reinforced at the bottom to prevent bending the head when driving. Its surfaces are rounded and smooth, eliminating accident hazards caused by sharp corners or edges. A raised ring indicates correct driving depth. The pole step is also available with Kortick knurling (K4252K) for improved safety. Kortick pole steps are fabricated from “carbon” steel bars. Hot dip galvanized, per latest revision ASTM Spec A153. Excess zinc eliminated by the Centrifugal Method.Threads are Fetter Drive with a cone point for easy driving into wood.
KORTICK
K4252
Thread Length
2-3/44-3/41143/4K4258Standard Hook
1105/8K4252Standard Hook
Height HookOverall LengthDiameter SteelStock NumberType Step
Pole Step for Wood Poles
KORTICK
K4252KKnurled Pole Step for additional climbing sasfety
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
5150
POLE LINE HARDWARE
POLE STEPS FOR FIBERGLASS POLES
Pole Step For Fiberglass PolesKortick Fiberglass pole steps have the same drive point design features as the K4252 series, available with square or square curved washer welded. Coarse thread Class 2 threads assembled with square washer, star washer, and square nut. The fiber-glass step is able to withstand 750lbs static loading without deformation. (19” version pictured)*Please inquire about customization options.
(SIDE VIEW)
(TOP VIEW)
ROD DIA = 0.75"
¾” STAR WASHER
3.25"
“A”
6.5" MIN
¼” WELDED/INSPECTEDPER A.W.S.D1.1
STEP END1.125"
NOTES:1. MATERIAL: STELL, LOW CARBON PER SPEIFICATION ASTM A 36 OR A3072. FINISH: ALL PARTS SHALL BE HOT DIP GALVANIZED PER SPECIFICATION ASTM 1533. COARSE THREADED TO CLASS 2 FIT4. WITHSTAND 750LBS STATIC LOADING
PART # “A”K4272 19"K4276 24"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
52
POLE LINE HARDWARE
DETACHABLE POLE STEPS
Detachable Pole StepsDetachable pole steps (K4553) allow for steps to be added as needed to keep unauthorized climbing. The mounting plate lag assembly (K4552) is permanently attached and the step is carried on the lineman’s belt. The K4570 is a combination pole step.
Mounting Detail
To install, assemble washer, which acts as a bearing plate for the step, to the Lag Screw anddrive the lag into the pole until the washer corners bite into the pole surface. Slip the slotted back
of the step over the special grooved head of the Lag Screw. The protruding lug on the washerkeeps the step in position when mounted. A nail driven through the nail hole prevents the plate
from possible turning. Steps, when mounted, project 5-½ inches from the face of the plate and areturned up at the extreme end to prevent linemen from slipping.
StepK4553Lag, ½” x 4" Plate, 2-¼” x 2-¾” x 3/16"K4552
DescriptionStock Number
7¼” (Approx.)
9/16"
2¼”1⅞”
CONTINUOUSWELD
SHEET STEEL
STEEL, DROPFORGED
NOTE 1: THIS END FITS K-4552 & A.T.&T. CO. “B” POLE STEP MOUNTINGS.
K4570 STEP, POLE DET COMBINATION, DETACHABLE B3599
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
5352
POLE LINE HARDWARE
WIREHOLDERSWire HoldersKortick wire holders lend themselves readily to all service requirements. Available in multiple variations with periscope brackets, span clamps, and periscope extensions. Wire holders are standard in nylon with porcelain available upon request. Please inquire for custom variations, thread types, and materials.
K4725Z NYLON SERVICE WIREHOLDER
NYLON KNOB7/8" X 1" HOLE
1 5/8" SQ
2 3/8"
1 5/8"
¾”
3/8” BOLT GALVANIZED
2 1/8”
3/8" LOCKWASHER3/8" HEX, NUT
K5927-3P-2 WIREHOLDER, STUD NYLON 3/8"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
54
POLE LINE HARDWARE
PERISCOPE BRACKETS
A. S. REG. SQ NUTS2 ¼”
21/
8"3/8" X 3" CARRIAGE
BOLT (FULL THREAD)½” X 3 1/8" STD. ROUND
OR OVAL HEAD PIN
K4582 BRACKET, W SPOOL SERVICE BRACKET. SAME FUNCTION AS K4593Z
NYLON KNOB7/8" X 1" HOLE
2 3/8"
¼" HEXNUT
WASHER,LOCK
K4593Z BRACKET, PERISCOPE NYLON, FOR 3-4" PIPE
1-5/8"
¾”
3/8" x 3" GAVLENIZED-FULLTHREAD CARRIAGE BOLTS
W/ HEX NUTS AND LOCK WASHERS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
5554
POLE LINE HARDWARE
SPAN CLAMP & PERISCOPE BRACKET
NYLON KNOB7/8" X 1" HOLE
1 5/8" SQ
2 3/8"
1 5/8"
¾”
3/8" X 3" BOLT, NUT &LOCKWASHER – 2 ¼” MIN.
THREAD
K8345Z CLAMP, SPAN, NYLON 3" SHANK
FLAT PLATE
#3 SUSPENSION CLAMP
3/8" X 4 ½” Carriage Bolt with 3 ½” min.
Thread
5/8" lock washer(2 ea required)
5/8" x 2" Machine Bolt w/square head and square
nut ( 2 ea required)
K8397 EXTENSION, PERISCOPE
AK4593Z Wireholder
Channel Extension
See AssemblyDetails
26-¼”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
56
POLE LINE HARDWARE
CLEVISClevisKortick Insulated spool type clevises provide an economical, convenient, mechanically strong and electrically efficient fixture. Mounting bolts are extra and should be ordered separately. Operating Voltages listed are based on average conditions and will serve only as a guide. Local requirements and climates must govern final selection of the clevis. Most clevises are available iron only or assembled with a porcelain or polymer spool upon request.
11/16" HOLE
1 ½” h
5/8" X 5 ½” PIN WITH 5/32" X 1
¼” HUMPED BRASS COTTER
PIN. 4 3/8”
11/16" HOLE
53/8"
CLEVIS COMPLETEWITH INSULATOR
K9104
INSULATOREQUIPMENT
CLEVIS LESSINSULATOR
K-524 K9254
Kortick K9104 is Recommended especially for 4000-volt primaries. The offset sides offer increased flash-over resistance over the ordinary straight sides at the pin end. Used principally for corner or dead end attachments
5"
2-½”
3 ¼”ASSEMBLY
K 526 INSULATOR (K9102 W/SPOOL K9252 W/OUT)
K9252 CLEVIS, IRON ONLY FOR K9102 5" EXTENSION
K9102 CLEVIS, W/K-526 SPOOL 5" EXTENSION
The K9102 provides excellent flash-over values. Recommended for circuits up to 2400 volts.
Ø11/16"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
5756
POLE LINE HARDWARE
CLEVIS
9"
CH 1-1/2" X 9/16" X 3/16"
K9291 CLEVIS IRON ONLYK9087 ASSY/WITH K-516 SPOOL
5/8" PIN WITH SS COTTER
A “S”4-3/4"
5"3/16" X 1" X 2"
1/8" X ½” X 1 ½”
STOCK CODE NoK9088K9107
A
Insulator “I”
STEEL SIZE(CHANNEL) “S”
“I”K516*K516*
*INSULATOR AVAILABLE AS POLYMER OR PORCELAIN SPOOL.
3 ¼”
11/16" X 7/8" SLOT
K9107 & K9088 ASSEMBLY W K-516IRON ONLY FOR K9257 & K9288
5" 1/8" X ½” X 1 ½” K522*K9116
K9107(P) Kortick Clevis is a standard secondary clevis, fits into 2” channel secondary brackets and clearance brackets for locking. Kortick clevis is standard at 5” clearance. K9088(P) clevis is the same as K9107 but heavier with 2” channel can mount on standard end or side of pole, facilitating low tension stringing
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
58
POLE LINE HARDWARE
CLEVIS
Round, ½”
½” Lock Washer½” Hex, Nut
½” X 6" GalvanizedHex, Bolt
B
A
STOCK CODE NoK9155K9158K9164K9165
A B3"
3 ½”4 ½”5"
2"2 ¼”2 ½”2 ½”
Kortick Strain Clevis is an efficient and economical Dead Ending Unit conforming to the latest revision ANSI specification.
3-3/8"
31/
8"
5"
NOTE:CLEVIS COMPLETE WITH INSULATOR- K9109, INSULATOREQUIPMENT-K516, CLEVIS INSULATOR- K9259
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
5958
POLE LINE HARDWARE
CLEVIS
INSULATOREQUIPMENT CLEVIS INSULATOR
K524K524
K9251K9251
CLEVIS COMPLETE WITHINSULATOR
K9101*K9101-5/8
4"
11/16" DIA
2 ¼”K 524 INS,
SPOOL ANSI53-1
*CLEVIS, DEADEND 5/8 PINK9101 is recommended for secondary application on circuits rated up to 750 volts. Provides sufficient conductor clearance for low voltage lines. Popular for Rural construction
½” PIN WITH COTTER KEY
4 ¼”
5/8”
1 3/8"
5/8"
DIA
FURNISHEDWITH PIN. 11/16"
HOLE
11/16" HOLE
Stock Code Description Long Description
K4450 CLEVIS, DEADENDING NO SPOOLK4450SP CLEVIS, DEADENDING NO SPOOL K4450 W/ 13/16 MTG HOLEK4547 CLEVIS, DEADENDING, NO SPOOL SAME AS K4450 EXCEPT HD STEEL,LESS PIN
The K4450 series dead ending clevis is used without a spool
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
60
POLE LINE HARDWARE
CLEVIS BRACKETS
Bolt Holes
K8423-Insulator Stand offBracket for Swinging Clevis
Holes Drilled forOvaleye and
Insulated ClevisAttachment.
(please inquirefor specificassemblies)
Apitong
A36 Steel
2½”
ROUND HOLE FOR⅝” MACHINE BOLT
KEY HOLE SLOT FORSWINGING CLEVIS
14"
K8348 Extension Bracket for K9109This unit is used to provide added clearance from pole face where required. “Key-hole” slot will
accommodate K9109, K9110, K9111, K9148, K9149, and K9259 Clevises.
1) Made from Mild Steel2) Galv. Per Latest ASTM Spec.
6-7/8"
¼”
1"
2½”
1¼”
1¼”
⅜”
20°
⅜”
4"
1⅝”
1⅝” Hole(Chamfer
Both Edges)
13/16" Hole
K8300 PLATE, SERVICE ATTACHMENTK8300SPP PLATE, SERVICE ATTACHMENT
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
6160
POLE LINE HARDWARE
CLEVIS BRACKETS3" x 1-½” x ¼” CHANNEL
15”
11/16" DIAHOLE
11/16"DIA HOLE
ASSEMBLE WITH 1 EA HEAVY DUTYCHANNEL CLEVIS
K8245 Clevis Bracket
HEX BOLT
11½” 8"
11/16" DIA. HOLE
5/8" HEX BOLT &LOCK WASHER
14"
BRACKET STRAP
The Single Spool Bracket is mounted to pole by use of two ⅝” mounting bolts.
K8242 w/out spool. K8242az assy clevis uses a K-516P Insulator (spool)Single Spool 14" Extension Rack
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
62
POLE LINE HARDWARE
SECONDARY RACKS
14"
16"
8"
8" 24"
14"
8"
8"
8"
K45284-Wire, 8 inch Secondary Rack
K45293-Wire, 8 inch Secondary Rack
The Extension backs are made from 3/16" x 1" x 2" channel to provide strength for a 14"extension from the pole face to the insulator center line. Use K516 or K517 insulators.
SECONDARY RACKS & BRACKETSThe standard Kortick secondary racks (K4528, K4529) are made of heavy-duty channel and provide 14” of clearance with 8” of spacing. Available in two, three, and four spool sizes. Also available with different clearance and spacing distances upon request, and the K8381 is available to add an additional spool if needed. Available to be shipped with Spools if requested (K4528A, K4529A)The K8348 provides additional clearance for K9109 clevis. K8423 Clevis Insulator standoff bracket creates standoff distance for various swinging clevis attachments. The K8245 comes with a spool type insulator assembled. Other variations are available; please inquire for more information.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
6362
POLE LINE HARDWARE
SECONDARY RACK EXTENSION BRACKET
Mounting Slot
14"
K8381 Extension Bracket for K4528, K4529For use with Rack K4528, K4529, K8272, and K8273 to add one additional insulator
(K516 not included).
Top Portion of the Extender mates with the lowest Clevis on the Rack to provide 8"spacing. The lower portion of the Extender is bolted to the pole with a ⅝” Crossarm
Bolt.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
64SWINGING BRACKETSPOLE LINE HARDWARE
12"
¾” RADIUS 5/16"
¾” RADIUS
5/16"9/16"
RADIUS
SWINGING BRACKET,¾” DIA. ROUND STEEL,
GALVANIZED
¼”
4"
BOLT, MACHINE, 5/8" x 7 ½”,GALV.
21/32" HOLE
1 5/16"
5/8"7/8" HOLEANGLE
2 ½” x 2½” x ¼” -2 ½” LONG, GALV
K8327
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
6564
POLE LINE HARDWARE
HARDWOOD BRACKETSHardwood Cross Arm Brackets:Untreated hardwood brackets per ANSI 05.6 Strongest cross sectional strength wood bracket. For more information please visit page 84 of the catalog.*Custom dimensions and designs are available. Please inquire for part numbers.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
66
POLE LINE HARDWARE
DISTRIBUTION INSULATOR PINSDistribution Insulator PinsKortick forges Insulator Pins from one piece, high carbon steel. The base distributes load and provides a firm seat on the cross arm.
A square shoulder provides a wrench grip to assist in tightening the pin and when lining up the insulator groove. (K7100 series, K7770 series, K7790 series, K7794)Kortick pins meet latest revision ANSI specification.
*Custom dimensions are available. Please inquire.**Pins available in both Nylon and Lead Thread
“A”
“B”SQ WASHER
SQUARE NUT
“C”
4"
1"
“E”
*Available with 1" inch Lead Thread as well
MF NUT
E
2
2
2
5
5
5
3 1/45/86 1/26*K7108Z
3 1/45/87 1/25*K7106Z
3 1/45/86 1/25*K7105Z
DCBASTOCK NUMBER
LONG SHANK TYPE for Flat Top Wood Cross arm – 1 inch NylonThread
DIMENSION. INCHES
1 ¾”
1 ¾”
1"
Lead Thread
5"
¼”
2"
5/8" Lockwasher5/8" Sq. Nut
¼”
¾” 1 ¼”
11/16" K7122
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
6766
POLE LINE HARDWARE
DISTRIBUTION INSULATOR PINS
1"K7795Z1-⅜”K7794Z“A”Stock No.
7"
1½”
¾”
LOCKWASHER
SQ. NUT
Z = NYLON .LEAD AVAILABLE AS WELL
A
“A”
“B”
TAPPED LIP WASHER
ROUND WASHER
LOCK WASHER
SQUARE NUT
“D” “D”
ROUND WASHER
SQUARE NUT
SQUARE WASHER
4” 4”
“T"
1¾"1¾"
“T"
Stock No.K7770zK7791zK7793zK7796z
Style2111
“A”5"5"7"5"
“B”7½"6½"7½"7½"
“D”⅝"⅝"¾"¾"
“E” “E”
“E”2"2"
2½"2½"
“T”1"1"
1⅜"1"
Z=NYLON.LEAD AVAILABLE (EX. K7770)
STYLE 1 STYLE 2
MF, LOCK NUT
K7140-Insulator Corner Pinwith 1" thread
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
68
POLE LINE HARDWARE
TRANSMISSION INSULATOR PINSTransmission Insulator PinsKortick forges Insulator Pins from one piece, high carbon steel. The large diameter base distributes strain and provides a firm seat on the cross arm.
The K7774-K7784, K7631 transmission series has a tapered body for strength.Kortick pins meet latest revision ANSI specification.
*Custom dimensions are available. Please inquire.**Pins available in both Nylon and Lead Thread
“A”
“B”
TAPPED LIP WASHER
ROUND WASHER
LOCK WASHER
SQUARE NUT
¾” ⅝”
ROUND WASHER
SQUARE NUT
SQUARE WASHER
4” 4”
1¾"1¾"
1⅜”
Stock No.K7774
K7774ZK7774-8 1/2
K7784K7784Z
Style22211
“A”7"7"7"
13"13"
“E” “E”
“E”3"3"3"
3½"3½”
STYLE 1 STYLE 2
1⅜”
1⅛" DIA. 1" DIA.
“B”7½"7½"8½"8½"8½”
MF, LOCK NUT
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
6968
POLE LINE HARDWARE
TRANSMISSION INSULATOR PINS
“A”
1¾”SQUARE NUT
SPRING LOCK WASHER1½”
“M”
Stock No.K7631
A7"
E3"
¾”
G1"
“K”
K1⅜”
“E”
“G”
Short Shank Type
M2⅜”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
70
POLE LINE HARDWARE
POLE TOP PINSThe Kortick Pole top Pin series (K7788 & K8124) are formed from a single pipe for maximum strength. Pole top pins are also available in channel, (K8076, K8079) or angle (K8107).
1 7/8"
1 ¼” X 11/16"SLOT
1"B
A
4½
”
9 G.A.
1¾
”
1 5/16"
Std. Cast Lead- SecurelyBonded to Pin
K8076K8106
K8122
K8076-DETAIL
11/16"HOLE
PRESSED STEEL CHANNEL, 1 INCH LEAD THREAD
STOCKCODE NO.
A
Mounting HolesDIMENSIONS IN INCHES
OverallLength
NumberSpacing
B C
Approx. ShippingWeight Pounds per
100 Pieces
K8076K8079K8083
151824
1 7/8 x 1 5/161 7/8 x 1 5/161 7/8 x 1 5/8
233
Size Steel
588
-56
284340620
PRESSED STEEL CHANNEL, 1 3/8 INCH LEAD THREADK8086K8087
2024
1 7/8 x 1 1/21 7/8 x 1 5/8
22
88
--
453680
STRAIGHT CHANNEL, 1 3/8 INCH LEAD THREADK8105 24 1 ¾ X 5/8 X 1/8 2 8 - 720
STRAIGHT ANGLE, 1 INCH LEAD THREADK8106K8107
1824
2 X 2 X 3/162 X 2 X 3/16
22
88
--
380550
C
EXTRA STRONG PIPE, 1-3/8 INCH LEAD THREADK8122K8123
2426
1-1/21-1/2
22
88
--
820960
K8124 28 1-1/2 2 8 - 1035K7788 22 1-1/2 CUSTOM DIMENSIONS
K8108 30 2 X 2 X 3/16 2 8 - 750
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
7170
POLE LINE HARDWARE
INSULATOR STANDOFF BRACKETS
STOCK CODENO. A
K8321ZK8323Z
30"28”
NYLON ORLEAD5/8" Sq nut, (2 each)
USED TO PROVIDE CLEARANCE FROM POLE FACE
A
L-DIAM.
1"1-3/8"
K8619 18" 1"
14¾”
8¼”
XY
THREAD
Stock Code Description x yK8374 PIN, EXTENDED 14-3/4", 1" L 1" 1.75"
K8380 PIN, EXTENDED L 14-3/4", 1-3/4" L 1.375 2.375
24" d
6-¾" d
STD. 1" LEAD THREAD &1-⅜” LEAD THREAD THIMBLEADAPTER
K4587 Stand Off Insulator Pin Bracket -with K4023 1-3/8" LeadThimble Adapter
K4587-1 Stand Off Insulator Pin Bracket W/out K4023
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
72
POLE LINE HARDWARE
INSULATOR STUDSInsulator Studs Kortick insulator studs are used to mount post insulators. Please refer to the drawings for the varying shank diameters and lengths. Studs fabricated from A36 carbon steel, hot dipped galvanized, and threaded to ASTM specifications. All Kortick Stud Types are available in custom sizes and assemblies. Please inquire for more details and custom assemblies.
¾”1 1/8"
1 ¾”
¾”
HEX NUT
LOCK WASHERS
K8366 Post Insulator Stud ¾ x 1 ¾”
¾”1 1/8"
2 1/2”
¾”
HEX NUT
LOCK WASHERS
K8366SPL Post Insulator Stud ¾ x 2 ½”
¾”
1 1/8"
1 3/4"
5/8”
HEX NUT
¾” LOCKWASHER
5/8” LOCKWASHER
K8364 Post Insulator Stud,5/8x 1-¾”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
7372
POLE LINE HARDWARE
INSULATOR STUDS
SQ. NUT
¾”1 1/8"
LOCK WASHER9”
5”
ROUNDWASHER
¾”
MF, NUT
K8365-9 Post Insulator Stud ¾ x 9"
¾”
1 1/8"
¾” LOCK WASHER
7 1/2”
¾” RD WASHER
¾”
¾” SQ NUT
¾” LIP WASHER
3 ½”
K8365 Post Insulator Stud, ¾ x 7- ½”
¾”
1 1/8"
¾” LOCK WASHER
4”
7 ½”
SQUAREWASHER
(2"X 2" X 1/8")
5/8"
SQ NUT
1 MF NUT
K8530 Post Insulator Stud 5/8 x 7 ½”
¾”
1 1/8"¾” LOCK WASHER
4"
SQ. WASHER (2 ¼” X 2 ¼” X 3/16")
¾”
SQ NUT
7 1/2”
MF NUT
K8365SPL ¾ x 7 ½”
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
74“V” CROSS ARM BRACESKortick “V” cross arm braces Kortick “V” cross arm braces are installed where conditions require more then flat brace construction.Braces are fastened to the pole with a 5/8-inch cross arm bolts, and to the cross arm with two ½-inch cross arm bolts or lag screws.Mounting Bolts and Lags are extra and are ordered separately.Hot formed from one piece of steel angle iron, and hot dip galvanized per ASTM 123 Braces conform with current revision of ANSI.
POLE LINE HARDWARE
11/16"Hole
9/16"Hole
9/16"Hole
AB
C
E
D
4-½”
F
¾” c
NOTE:STEEL: NET BILLET BASIC OPEN HEARTH, ASTM A-107(LAT. REV)FINISH: GALVANIZED PER ASTM A-153(LAT REV)
MATERIAL STOCK # A B C D E F CUT LENGTH1-1/2x1-1/2x3/16 K1811 40 37 12 18-1/2 4 2-1/4" 47-5/8"
K1812 45 42 12 21 4 2-1/4"K1813 51 48 14 24 4 2-1/4" 57-1/2"
K1813 1/2 51 48 14-3/4 24 4 2-1/4"K1814 51 48 18 24 4 2-1/4"K1815 63 60 18 30 4 2-1/4" 6' 1-15/16"
1-3/4x1-3/4x3/16 K1818 63 60 18 30 4 2-1/2" 6' 3/4"K1819 69 65 20 33 4 2-1/2" 6' 8-1/2"K1820 75 72 18 36 4 2-1/2" 6' 11-1/8"K1821 75 72 22 36 4 2-1/2" 7' 3-1/2"
2x2x3/16 K1822 75 72 22 36 4 2-1/2" 7' 3-3/8"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
7574
POLE LINE HARDWARE
Kortick flat cross arm braces are designed to support wood cross arms carrying tangent loads. Rounded corners on the brace ends prevent damage and reduce the possibility of injury. Minimum tensile strength at the bolt holes is 7,000 pounds. Hole centers are one inch from end of brace. Braces Manufactured to latest revision ANSI specification. Also available with custom hole sizes, Kortick is equipped to manufacture any variation on this spec as needed.
FLAT BRACE
A
B1" 1"
HOLE 9/16" DIA HOLE 7/16" DIA
Y
W
1 ¼” (W) X ¼” (Y)BRACE STOCK
1 7/32" (W) X 7/32" (Y)BRACE STOCK
K1420K1422K1424K1426
K1720K1722K1724K1726
K1428 K1728K1430 K1730K1432
-K1436K1412
*K1436SPL
-K1734
---
STOCK NO.
A B
20222426
18202224
28 2630 283234361436
3032
341234
DIMENSIONS IN INCHES
*SPECIAL CROSS ARM BRACE WITH9/16" DIA HOLES ON EACH END
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
76
POLE LINE HARDWARE
ALLEY CROSS ARM BRACEAlley Crossarm BracesWhen a cross arm can be mounted on only one side of the pole, an alley cross arm brace may be used. Used correctly it will ensure the correct alignment of the power and distribution lines.K1950 series Kortick Alley arm braces are hot formed with equal leg angle. Care is taken at the bends to maintain a gap in the fold, allowing for proper galvanizing and corrosion prevention. The brace and step are galvanized separately, then riveted with high strength aluminum alloy. Separately galvanizing step and brace prevents acid bleeding and future corrosion concerns. The Step has an exaggerated lip at the end to create a stronger, more reliable foothold. Kortick Alley Arm Braces conform to latest revision ANSI specification.Recommended assembly for alley arm braces at a 45 degree angle. K8300 series is similar to the K1950 series in construction but fabricated using heavy duty 2 1/2x2 ½ angle. The K8309 has a second step. K8511 angle alley arm brace is hot formed eliminating the need for a cold bend cut seen elsewhere in the industry, used for heavy-duty applications.
7/16 ob Hole For3/8 o Rivet
B9" b
CE Hole
5" g1" c
A
Stock Size StepNo. Angle Stock A B C D EK1951 1½x1½x3/16
3/16x1¼ 60e 30d ¾c ⅝c 9/16bK1952 1½x1½x3/16
3/16x1¼ 72e 30d ¾c ⅝c 9/16bK1966 1½x1½x3/16
3/16x1¼ 84e 30d ¾c ⅝c 9/16bK1953 1¾x1¾x3/16
3/16x1½ 60e 30d ⅞c ¾c 9/16bK1954 1¾x1¾x3/16
3/16x1½ 84e 30d ⅞c ¾c 11/16bK1955 2x2x¼ 3/16x1¾ 120e 50d 1c ⅞c 11/16b
All Dimensions in Inches
Steps
D C B
A
3/16" x 2-1/2” x 2-1/2” Alley Arm Braces(Similar To type B Alley Arm Brace)
Stock No. A B C D # StepsK8308 7'0" 3'1" 0 3'11" 1K8309 10'0" 3'3" 2'3" 4'6" 2
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
7776
POLE LINE HARDWARE
ALLEY CROSS ARM BRACE
HOLES 11/16" b
HOLES 11/16" b
A A
8' f4' f 4' f
HOLES 11/16" b
K8511 Alley Cross Arm Brace 8' Heavy Duty
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
78
POLE LINE HARDWARE
VERTICAL BRACESVertical braces are used to support multiple cross arms, one above the other.
AD
B
Items Made of SteelHot Dip Galvanized After Fabrication
ASTM A123 / A153
1"
E11/16"11/16"11/16"11/16"11/16"
K8319 8'-2" 1 3/8" 4'-0" 8'-0" 11/16"6'-8"3'-4"1 1/8"6'-10"K83185'-8"NA1 1/8"5'-10"K83174'-0"NA7/8"4'-2"K83163'-0"NA7/8"3'-2"K83152'-0"NA7/8"2'-2"K8314
DCBASTOCK CODE
Vertical Brace CLIP CORNERS FORK8317, K8318, K8319
C C
1"
E = ALL HOLES
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
7978
POLE LINE HARDWARE
VERTICAL BRACES
11/16" Hole11/16" Hole
AB
C
Part No. Description A B C .K8400 Brace Vert. Angle 36", 1½” x 1½” x 3/16" 38" 36" ⅞”K8401 Brace Alley Arm 13', 2½” x 2½” x 3/16" 156" 153" ⅞”K8402 Brace Alley Arm 10', 2" x 2" x 3/16" 120" 117" ⅞”K8403 Brace Alley Arm 7', 2" x 2" x 3/16" 84" 81" ⅞”
Items Made of SteelHot Dip Galvanized After Fabrication
ASTM A123 / A153
11/16" Hole 11/16" Hole
AB
D
Part No. Description A B C DK8406 Brace Special Angle 6', 2” x 2” x 3/16" 74" 72" 4½” ⅞”K8407 Brace Special Angle 4', 1¾” x 1¾” x 3/16" 50" 48" 4½” ¾”
Items Made of SteelHot Dip Galvanized After Fabrication
ASTM A123 / A153
C C
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
80
POLE LINE HARDWARE
BACK BRACESBACK BRACESKortick Back Braces are installed to reinforce wood crossarms at terminal poles, on corner construction, and where an angle in the line is necessary.
1"
1¾"
37"
2½”
1¾"
11/16" HOLES – 2 PLACES
K8516
1-¾ x 1-¾ x 3/16 – Inch Angle72"K198660"K198548"K1984
1-½ x 1-½ x 3/16 - Inch AngleOverall Length ‘A’Stock Number
Back Braces
4"11/16" Hole
A
7"
9/16" Hole
109"K198894"K1987
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
8180
A 51.0
POLE LINE HARDWARE
GUARD ARM & ROUND BRACESGuard Arm and Round BracesKortick Guard Arm Braces are attached to one side of the guard arm for additional support at those points on the pole where cable or drop wire is suspended. Twists are hot fabricated and, hot dip galvanized per latest revision ASTM Spec A153. Mounting bolts and Lag screws are extra and should be ordered separately.
Round BracesRound cross arm braces (K8226 series) for raptor protection. Used in place of wood transmission cross arm braces when accept-able. Applications requiring higher strength with the improved strength to weight ratio of pipe.ORDERING INSTRUCTIONS:Above Catalog Nos. and Codes refer to one brace. The brace may be used in either the right or the left hand position. Order two braces per crossarm (as shown above).
Installation
K1901 BraceK1901
7/16" Hole ¼ X 1 ¼” Steel 9/16" Hole
¼ x 1-¼18"K1901Hole SpacingLength OverallStock Numer
CL
CL
CL
11/16" Dia.
6" Min. Typ.
Length
Spacing
13/16" Dia.
Length
Angle
(SeeTable)
CAUTION: WHEN STEEL PIPE BRACESARE UTILIZED THERE SHALL BE 36"BETWEEN THE CROSSARM BRACE
THRU BOLT AND THE NEXTCONDUCTER LEVEL BELOW.
NOTE:To Provide raptor protection, steelcrossarm braces should not be used onstructures located within Bureau of LandManagement areas.
ORDERING INSTRUCTIONS:Above Catalog Nos. and Codes refer toone brace. The brace may be used ineither the right or the left hand position.Order two braces per crossarm (as shownabove).
38½13284K82293610866K8228369660K8227
38½8454K8226ANGLE (Degrees)SPACING (Inch)LENGTH (Inch)STOCK NUMBER
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
82
POLE LINE HARDWARE
STEEL CROSS ARMSSteel Cross ArmsDead-end steel cross arm are used as a single or double dead ending arms (please order additional eye nuts for double dead end use). Holes punched for pin type insulators or post type insulators are provided to mount at one or both ends. Cross Arm also available in other lengths and strengths upon request.
K8398Crossarm made with 4"x 5/4lb channel and 5"
channel for the gain. Arm and gain are welded together with gussets each side to addstrength and rigidity. Assembled with 5/8" Eye Bolts for dead ending. Mount to the polewith 5/8" Cross arm Bolts. Can be used as a ‘double dead end’ by adding 5/8" Oval eye
Nuts to the back of each Eye Bolt.
13/16"HOLE
5/8 FORGEDSHOULDER EYE
BOLT
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
8382 WOOD CROSSARM ASSEMBLIESWood Cross Arm AssembliesKortick wood cross arm assemblies save time and money. Pre-assembled with quality Kortick Hardware, they are avail-able in varying lengths, duties, and assemblies. Please inquire with engineering for custom design requests. Pictured: A few generic assemblies. Top. one example of a standard crossarm assembly.Bottom. Dead end assembly with hardwood desgined for dead nd strength applciation
POLE LINE HARDWARE
HIGH VOLTAGE 4 ¾”
STOCK CODE NO.
22
1
QUANTITY
3AK7108Z
Sign, High Voltage 3 5/8" x 13 ¾”
Brace, Flat 28" Length
Cross Arm, 3 ¾” x 4 ¾” x 8'-0"
DESCRIPTION
Pin, Wood Cross arm 5/8" x 6 ½” Shank
23
2K2908
Bolt, Machine 3/8" x 5"
Washer, Static Proof Spring, 5/8" & ¾”
Washer, Static Proof Spring, 5/8" & ½”
K1005
K2909
Wood Cross ArmKPL10123
K1428
Wood Cross Arm
KPL10123
K1428
K7108Z
K2909
K2908K1005
TOP VIEW
FRONT VIEW
Dead End Assemblies:Custom specification, design, and assemblies are available.Example pictured below with Shouldey bolts and heavy duty bracing. Please inquire
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
84HARDWOOD PRODUCTPOLE LINE HARDWARE
The Ideal Wood Cross Arms Naturally Durable Hardwoods
All hardwoods originate from Managed
Forests, Certified by the Forest Stewardship Council with Chain of Custody
DESIRABLE ATTRIBUTES- Natural amazon wood requiring no
preservation treatment- High mechanical strength (Fiber Strength)- Field life - 80 yrs
o Resistance to moisture absorption o High resistance to roto High resistance to termites and wood peckers
- High flame resistance (Charring Rate-3mm)- No disposal issues- Very high salvage value- No changes in field work practices- Life-cycle cost is less than 1% the lifecycle cost of
the treated Doug Fir cross arms
Environmental Stewardship -- Promote environmental stewardship to mitigate preservation treatment of wood, as well as Promote Sustainable Forest Management Practices For More information on FSC forests: http://www.fsc.org/ http://www.greenpeace.org/international/en/campaigns/forests/solutions/alternatives-to-forest-destruc/
Approved by the Standards Review Board in 2010 as: ANSI O5.6 – All Natural Durable Hardwoods Cross arms and Braces – Dimensions & Specifications
For more information, please contact us at; Kortick Manufacturing: 2230 Davis Ct, Hayward, CA 94545
Phone:(510) 856-3600 e-mail: sales@Kortick.com
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
8584 HARDWOOD PRODUCTPOLE LINE HARDWARE
Stock code Description Dimension Ultimate Force Doug Fir Equivalent Ultimate ForceKWDH10032 HARDWOOD, CROSS ARM 8' LIGHT 2.75"X3.75"X8' 2,062 3.75"X4.75"X8' 1,975KWDH10045 HARDWOOD, CROSS ARM 8' HEAVY 3.75"x4.75"x8' 5,740 4.75"X5.75"X8' 5,314KWDH10047 HARDWOOD, CROSS ARM 8' EXTRA HEAVY 4.25"X5.25"X8' 7,860 5.75"X6.75"X8' 7,331KWDH10052 HARDWOOD, CROSS ARM 10' LIGHT 2.75"X3.75"X10' 2,050 3.75"X4.75"X10' 1,822KWDH10055 HARDWOOD, CROSS ARM 10' HEAVY 3.75"x4.75"x10' 4,510 4.75"X5.75"X10' 4,102KWDH10057 HARDWOOD, CROSS ARM 10' EXTRA HEAVY 4.25"X5.25"X10' 6,183 5.75"X6.75"X10' 5,760
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
86
GainsK4325 Telephone design reinforces between cross arm and pole for improved rigidity. Will accommodate 5/8 and ¾ bolts. Steel Gain offers improved performance in fires over plastic designs.Wood Grid Gains strengthen bolt connections by distributing load and allowing for drainage. (KXPG49 pictured)
POLE LINE HARDWARE
GAINS
5 ¼”
2"
13/1
6"cx
4"
3/16" Rad.
7/8"
K4325 GAIN, POLE STEEL 4" X 5"
C
1/4”
3” 3”D
5 ½” R
B A B
HOLE A HOLE B
31/32" 31/32" KXPG46 GAIN, GRID 6-3/4"X 4" C=4" D= 6-3/4", A HOLE ONLYKXPG44 GAIN, GRID, 4" x 4" C=4" D=4", A HOLE ONLYKXPG49 GAIN, GRID 9" X 4.5"(pictured) C=4.5" D=9", A, B HOLE*BC add BC to part number for "with Bonding Clip"
alternate hole sizes available upon request
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
8786 CROSS ARM REINFORCINGPOLE LINE HARDWARE
Kortick Cross Arm reinforcing hardware is used in a wide array of applications to reinforce wood and add additional strength at points of excess strain. The plates are the quiet workhorse of the Pole Line Hard-ware Industry. Custom specs and applications are available please inquire for further information.Plates distribute the load in tension over a greater surface area and reinforce the wood fibers of a pole against shear resulting from excessive down pull.
CL
CL7"
1'-9½”
13/16" Hole11/16" Holes on 5"
Bolt Circle
13/16" x 3¼” Slot13/16" x 3¼” Slot
Double Arming (K8399)
11/16" Hole
2"
11/16"
5⅞”
CROSSARM BEARING(K8341)
2-9/16" x 1" Slots
2"
4½”
U BOLT(K8343)
6"
CL
CL
13/16" Hole
¾”
5⅞”
PIN BEARING(K8344)
The above gives a general idea of the many types of“Plates” available. If one of the above units does notsolve the problem, please refer your specifications to
the nearest Kortick representative.
Plate Facilitates mounting a pin type insulator, line post insulator, or station post insulator to two crossarms
Cross arm reinforcing plate prevents the arm from splitting or checking and protect the wood fibers at points of strain.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
88CUTOUT BRACKET ARMSCutout Bracket ArmsK8425, K8425-48, and custom Cutout Arms are available in hardwood and fiberglass with Channel mounting brackets, and indi-vidual cutout mounting brackets. Please see page 84 for additional information on hardwood. Please call for testing data showing Hardwood’s improved numbers over apitong.The AK8425CHANNEL Mounting Bracket provides additional strength. Available as an assembled arm or individual components as needed.
POLE LINE HARDWARE
4"PLATE
4" CHANNELAK8425CHANNEL
AK8425BRKT¼” X 2"
PLATE+HDWARE
K8425 BRACKET, COMBO CUTOUTARM-FIBERGLASS 96"
BONDINGLUG HOLE
Cutout Bracket ArmsK8425 in Hardwood. 2” plates. all other hardware is the same as drawn above.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
8988
POLE LINE HARDWARE
CUTOUT & ARRESTER BRACKETS
Cutout and Arrester BracketsKortick Cutout Mounting Brackets and Cutout/Arrester Combo Brackets are customizable to varying hardware assemblies, strength requirements, and cross arm dimensions, please inquire for further information. K8440, K8377 and K8379 are the Kortick Standard designs. The K8363 mounts a cutout, arrestor, or termination while providing 20” of clearance from pole. The K8361-1 mounts three cutouts, arresters, or terminations. (adapter plates available to mount three each-cutouts and arresters).
6-¾”4-⅛” to 5-5/32"
2-11/16" to 4" MAX
1/32" R at corners
11/16" DIA (A)
45°
3-¾”
1" MAX R
K8440 BRACKET, CUTOUT MOUNTING
NOTES:ASSEMBLE EACH UNIT WITH2 EACH:· 3/8 x 1-½ CARRIAGE BOLTS· 3/8" LOCKWASHERSGALVANIZED TO LATEST ASTM SPECIFICATION
9/16” Square Hole
2 - 7/16” Square Hole
7¾”(Approx.)
20°
3/8" RADIUS(APPROX)
K8377 Bracket, Cutout Attachment
2⅝”
8⅛”
K8379 Arrester or CutoutBracket for mounting on
crossarms or poles. Will fitcrossarms up to 3-¾” x 4-¾”.
Complete with bolts andwashers.
⅜” x 1¾” Steel
K8379 BRACKET, CUTOUT/ARRESTER MTG
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
90
POLE LINE HARDWARE
CUTOUT & ARRESTER BRACKETS
½” X 2" HDG Carriage Boltw/ helical Spring, lock washer, and hex
nut.
½” X 2" HDG Carriage Boltw/ helical Spring lock washer external
tooth, and hex nut.
13"
5½
”
17 ¼”
K8361-1 BRACKET, TRI-MOUNT
Used to mount one (1) or two (2) cutouts to the polewhere greater clearance is desired. Unit mounts with
two (2) ⅝” machine bolts.
5"
20"
SQUARE HOLES FOR ½” CARRAIGE BOLTS (COMPLETE WITH ONE BOLT & WASHERS)
11/16" DIA. HOLES
9/16" DIA. HOLES
¾”
1⅞”
K8363 BRACKET, CUTOUT MOUNTING
4" CHANNEL POLE BACK with Mounting Slotsfor 5/8" Bolts on 10" centers. (Top Hole is Key
Hole – Bottom Hole is open Slot)
¾”
¾”1 ½”
4 ½”
17"
40"
40" ANGLE ARM welded to 4"channel pole back (weld all around)
½” Bonding Bolt
Assembly (one each side)
½” x 2" Carriage Bolt with Lock washer (2 per leg)
K8353 Bracket, Trimount, Arrester
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
9190
POLE LINE HARDWARE
INSULATOR POLE TOP BRACKETSInsulator Pole Top BracketsK8257 Pole top Bracket for 35kv Vertical Post insulator and K8257-69 for 69kv vertical post insulator.
Bonding Lug
11/16" DIA
11/16" x 1"
8"
6"
13/16" Dia.
K8257 BRACKET, VERT POST INS
K8257-69 BRACKET, VERT POST INS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
92
POLE LINE HARDWARE
INSULATOR POLE TOP BRACKETSInsulator Pole Top BracketsK8259 series (for 69kv and 115kv applications) provides strength and flexible design. A complete pole top Bracket consists of a top plate and a mounting bracket for a 69kv or 115kv insulator. The top plate and mounting bracket may be made up in any special combination of the two parts. The standard 69kv includes a 69kv bracket body and a pole top plate (K8259pl-69), plus assembly bolts and bonding material per the drawing. The standard 115kv part #k8259-115 includes the 115kv bracket body and pole top plate part # K825pl-115, plus assembly bolts and bonding material per the drawing. Special 115kv top plate part # K8259pl-115spl is available for a larger sized pole top up to a class H6 Pole, per the drawing.
Side View
9"
20"
45°
12"
8"
11/16" x 3¼” Slotted Holes (4)
4 holes 11/16" o on 5" BoltCenter 13/16" Center Hole
⅜” Plate for 69KV.½” Plate for 115KV.⅞”
⅜”
Pole Range 6" to 11"
Top ViewTop Plate (See Detail)
Standard 69KV. PoleTop BRKT. Part
K8259-69With a ¼” Body
For 115 KV. BRKT.K8259-115
With a ⅜” Body
13/16" Slots
Bonding Lug
5"
¼”
1-½”
v
12"
8"
11/16" x 4¾” SLOT (4)
115 KV STANDARD PLATE
16"
8"
13/16" HOLE
STOCK No. K8259PL-115SPL
½” PLATE
4 HOLES
11/16" x 3¼” SLOT (4)
11/16" o on 5" Bolt Circle
115KV. Special Top Plate for ANSI Class 4 toH6 Pole Top w/6" to 13"D.
STOCK No. K8259PL-115
4 HOLES
Ø13/16"
5/8"
7/8"
5/8"
7/8"
½” PLATE
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
9392
POLE LINE HARDWARE
SIDE INSULATOR BRACKETSide Insulator BracketsThe K8360/K8371 and KBR10006 are for use with line post insulators in distribution or transmission to increase conductor clearance or give added climbing space. Pole end of bracket curved to fit a wood pole. Custom variations are available; please inquire for further detail. The KBR10006 is designed for 69kv lines.
A
6 ¼”10"
5
6"
Stock Code Description A
KBR10006 BRACKET, POST INS, 14" HORIZ 14"KBR10006-9 BRACKET, POST INS, 9" HORIZ 9"
A
“A”
“C”
2½”
11/16” Dia. Hole
“B”
11/16” x 1¼” Slot
Brace (Both Sides)
13/16” Dia. Hole –Centered on a4" x 5" Surface
Bonding Bolt(1" From Back Edge)
Yes12°12"20"K8371No15°10"9"K8360
BraceCBAStock No.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
94
POLE LINE HARDWARE
TRANSFORMER BRACKETSTransformer BracketsKortick Transformer Brackets conform to NEMA standard. K8350 and K8351 Are open delta brackets for two transformersKBR10120 three phase transformer bracket’s center pole gain is made of heavy duty channel to improve strength.K6300 and K6303 are single transformer hook brackets.
13/16" Dia.Mounting
Holes
Pole BoltSpacing 31”
3"
2¼”
50"6"
StandardEEI_NEMAHole size
and Spacing
11½”
Fabricated Steel:Hot Dip Galvanize A.S.T.M. A123 / A153
Ratings:Ultimate Load = 4000 Lbs. per Position
¾” DIA. Mounting BoltsTensile Strength = 18,000 Lbs.Shear Strength = 11,000 Lbs.
KBR10120 BRACKET, TRANSFORMER MOUNTING
6- 5/8" x 2-½” AND 6- ¾” x 2-½” MTG.
BOLTS FURNISHED
13/16" THROUGHBOLT SLOTS
24"
12"6-¼”
1"
12"“A” “A”
“B”
3"SLOT 13/16" x 13/16"
2-½” RAD.
2-½”
4"
¾”
WELD ALLAROUND
“C”
“D”
4"K6303
DIM K6300 K6303"A" 1-1/2" 2-1/2""B" 6-3/4" 10-3/4""C" 27-3/4" 41-3/4""D" 5-3/4" 6-3/4""E" 5/8" 3/4"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
9594
3"
“B”
“A”
4" R.
24" 26"
KEY-HOLE SLOT FOR ¾” BOLT
STANDARD EEI-NEMAHOLE SIZE AND SPACING(ALL HOLES AND SLOTSFOR ¾” OR ⅝” BOLTS)
SLOT FOR ¾” BOLT
The transformer bracket is attached directly to the pole with ¾” bolts. Twotransformers can be mounted on the unit in “Open Delta” or “Parallel”.
8-½”6-¼”K83515"4"K8350“B”“A”Stock No.
TRANSFORMER BRACKETSPOLE LINE HARDWARE
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
96
POLE LINE HARDWARE
CONDUIT STANDOFF BRACKET
K6411 K6412
K6413
9/16" Dia.Holes (2 ea)
3"
4 ½” or 7 ½”
0-6" size conduitSlottedaluminum
band
9/16" dia. holes
6"
0-6" size
conduit
8 3/8"
9/16" dia. holes
1 ¾”
0-6"s
izeco
nduit
6" to 7"
Slottedaluminum
band
NOTES: All material except aluminumband is galvanized.
Dimensions +/- 1/16"
3 ½”
Conduit Brackets (K6411,12,13Series), with standoff distance,for one, two, or three conduits.
Conduit Stand off BracketsAbove-K64 series with flat bar and aluminum designBelow-KB1965 series with strut. Please inquire for length, part numbers, and design specifcs.
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
9796
POLE LINE HARDWARE
END OF ARM TAKEOFF BRACKET
POLE LINE HARDWARE
VERTICAL EXTENSION BRACKET
¾” MOUNTING BOLTS(NOT INCLUDED)
1½” HOLE20°
FULL WELD
20"
K8388 BRACKET, VERTICAL EXTENSION CORNER CONSTRUCTION
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
98
POLE LINE HARDWARE
EXTENSION LINKSExtension LinksThe Kortick K8258 series extension links are heavier duty then industry standard. Strong and reliable in crucial situations at dead ends and corner structures when additional climbing space is needed.Kortick’s K8355 series extension links are a single bar fabricated from a thick ¼” steel and Hot Dip Galvanized per A153. Kortick K8358CN clevis nut works in conjunction with the K8355 series.KIF10180 is a lighter weight extension link similar in function to the K8258 series.
¾”
5/8" COTTER BOLT
¼” X 2" FLAT BAR
11/16" CHAMFERRED HOLE
A
Square Bolt with Lock Washer andNut
Pictured:Stock Code Description "A" MaterialK8258-10 LINK, EXTENSION, 10" 10" FOR TRANS AND DIST 1/4" x 2"K8258-12 LINK, EXTENSION, 12" 12" FOR TRANS AND DIST 1/4" x 2"K8258-18 LINK, EXTENSION, 18" 18" FOR TRANS AND DIST 1/4" x 2"K8258-24 LINK, EXTENSION, 24" 24" FOR TRANS AND DIST 1/4" x 2"K8258-42 LINK, EXTENSION, 42" 42" FOR TRANS AND DIST 1/4" x 2"
Not pictured:K8355 LINK, EXTENSION 5" SINGLE BAR 1/4" 1-1/2"K8358 LINK, EXTENSION 14" W/CN SINGLE BAR 1/4" 1-1/2" K8358CN NUT, CLEVIS FOR K8355 SERIESK8359 LINK, EXTENSION 30" SINGLE BAR 1/4" 1-1/2"
KIF10180 LINK, EXT, 14" CLEVIS-EYE SIMILIAR TO K8258 EXCEPT ONE BOLT. 3/16" x 1- 1/2"
K8258 Series Dwg
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
9998
POLE LINE HARDWARE
EXTENSION LINKSHeavy Duty Extension linkMade of 3/8 steel for heavy duty applications. Please inquire for part numbers and specific design requirements.
9/16"
3/8"
6 ¾”
4"1 ¼”
½” HOLE x2
13/16” HOLE x2½”
CLEVIS PIN WITHCOTTER PIN
BOLT WITH LOCKWASHER AND NUT
¾” HOLE x2
5/8"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
100
San Francisco Giants Stadium including Kortick hardware
Bay Bridge built with Kortick hardware
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
101100
POLE LINE HARDWARE
WOOD POLE EXTENSIONSWood Pole ExtensionsWood Pole Top Extensions provide for additional length from 5’-8’ while maintaining the same class of pole. Strong enough to guy and run attachments, bolted together with ¾” x 2-1/2” Grade 5 Hex Head Bolts (four). Provide ¾” gap between Top Pole Top Extension and New Pole section. Provide 2 ¼” gap below Pole top Extension and Existing Pole to install Nut and Washer on Bolt.
Bolted with ¾” x 2 ½” Hex Head Bolts w/ Roundwasher, Lock washer, & Heavy Hex Nuts. (4 ea)
All Slots 4"x 13/16". Plates slide for pole range of7"-11" Diam.
K8510 EXTENSION, POLE TOP
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
102
POLE LINE HARDWARE
ANTI CLIMBING DEVICEAnti Climbing DeviceAnti Climbing Devices for lattice transmission towers, fencing, and other security applications, hot dip galvanized per ASTM spec. Hardware included for quick attachment.
3
32
1
C
2 5/8"
2"
1"
2"
2 3/8"
(4) 7/16" HOLE
4 1/16"
48"
3
2L
Notes:1) Hot Dip Galvanized (ASTM A-153)2) Hot Rolled3) Carbon Steel (ASTM A-569)
(table A)
KXACG-4 ANTI CLIMBING DEVICE 4'
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
103102
Kortick ladders are formed with the hooks hot forged as a part of the single piece of steel for additional strength. Rungs are forged from “bolt” steel with twelve-inch centers and riveted for maximimum strength. All ladders shipped singly.**Please inquire about custom spec ladders. Kortick manufactures a variety of ladder styles.
UNDERGROUND
MANHOLE LADDERS
12"
“W”
12"
(L) LENGTHK5275K5276K5277K5278
5'-10"6'7'8'
K5279 9'K5280 10'K5281K5282K5284K5286
11'12'14'16'
STOCK NO.“L
” (se
eta
ble)Number of
Steps3/8" X 1 ½”3/8" X 1 ½”3/8" X 1 ½”3/8" X 1 ½”
4567
3/8" X 1 ½” 83/8" X 1 ½” 93/8" X 1 ½”3/8" X 1 ½”3/8" X 2 ½3/8" X 2 ½”
10111315
(R)Steel Size
9 1/8" Approx.
1'-0"1'-0"1'-0"1'-0"1'-0"1'-0"1'-0"1'-0"1'-0"1'-0"
(W) WIDTH RUNG
5/8"5/8"5/8"5/8"5/8"5/8"5/8"5/8"5/8"5/8"
“R”
See Detail b
Detail b
12"3 ½”
ANTI-SLIPKNURLING
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
104CHANNEL LADDER WITH WELDED HOOK
14" MIN14 ½” MAX
6"
12"12"
CLEAR
6" MIN12" MAX
A A
12 Ft.NORMAL
HOOKSEE
DETAILS
4"
2"
STANDARDHOOK
Stock Code DescriptionK8578 8'K8579 9'K8580 10'K8581 11'K8582 12'K8583 13'K8584 14'K8585 15'K8586 16'
Channel Style with welded manhole stephook
UNDERGROUND
UNDERGROUND
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
105104
UNDERGROUND
CABLE RACKSCable RacksKortick Underground Cable Racks support the cable runs in manholes and interior cable vaults. Cable racks are fabricated from l-1/2 x 9/16 x 3/16-inch C1040 Grade Channel Steel. Special slots rigidly grip and support the cable hook. Mounting holes are 11/16 x 13/16 inches. Racks attached to the wall with 1/2-inch Bolts and Expansion Shields. Cable racks are available in lengths ranging from 8 holes to 47 without tab and 8 to 18 holes with tab. Kortick Cable racks are made with industry standard hole spacing of 1 ½ inches. The with Tab Cable Racks (not pictured) interlock to create longer cable racks when needed.
A
A
1 ½” X 9/16" X 3/16"CHANNEL
1 ½” 5/8"
5/16"
9/16
"
1/8"
1 ½”
3/16
"
SECTION A-A
X
Stock Code DescriptionK5108 RACK, CABLE 8 HOLE W/ TABK5114 RACK, CABLE 14 HOLE W/TABK5118 RACK, CABLE 18 HOLE W/ TABK5120 RACK, CABLE 37 HOLE W/O TABK5122 RACK, CABLE 47 HOLE W/O TABK5150 RACK, CABLE 8 HOLE W/O TABK5152 RACK, CABLE 12 HOLE W/O TABK5153 RACK, CABLE 14 HOLE W/O TABK5155 RACK, CABLE 16 HOLE W/O TABK5156 RACK, CABLE 18 HOLE W/O TABK5160 RACK, CABLE 22 HOLE W/O TABK5162 RACK, CABLE 24 HOLE W/O TABK5164 RACK, CABLE 27 HOLE W/O TABK5165 RACK, CABLE 28 HOLE W/O TABK5166 RACK, CABLE 32 HOLE W/O TABK5170-43 RACK, CABLE 43-HOLE W/O TAB
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
106CABLE RACK HOOKS & B MANHOLE STEPUNDERGROUND
K5255 HOOK, CABLE RACK 4" PRESSED STEELK5256 HOOK, CABLE RACK 7 1/2" PRESSED STEELK5257 HOOK, CABLE RACK 10" PRESSED STEELK5258 HOOK, CABLE RACK 14" PRESSED STEELK5259 HOOK, CABLE RACK 18" PRESSED STEEL
BA
CDimensions in InchesA B C
K5261 16 12 2K5262 14.5 12 2
B Manhole Steps
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
107106
UNDERGROUND
PULLING IN IRONS
C
½” RADIUS x2
NOTES:1. STEEL: NEW BILLET CARBONSTEEL, LATEST REVISION A.S.T.M.A.-1072. GALVANIZE- HOT DIP, LATESTREVISION A.S.T.M.A.-153
B
AØ7/8"
1" RADIUSPART # A B CK5244-¼ 4-¼ 5-3/8 5-¼K5247 7 7 4K5248 8 7-3/8 4K5251 9 8 4K5252 10 10-½ 4
NOTES:1. STEEL: NEW BILLET CARBONSTEEL, LATEST REVISION A.S.T.M.A.-1072. GALVANIZE- HOT DIP, LATESTREVISION A.S.T.M.A.-1533. notes not applicable to Stainless steelparts
C
½” RADIUS x2
B
AØ7/8"
1" RADIUS
PART # A B CK5244-¼SQ 4-¼ 5-3/8 5-¼K5247SQ 7 7 4K5248SQ 8 7-3/8 4K5251SQ 9 8 4K5252SQ 10 10-½ 4
*Also available in 316 Stainless Steel.Please add “SS” to part number for stainless steel order request
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
108
UNDERGROUND
UNDERGROUND HARDWARE
Stock Code Description Long DescriptionK6085 SUPPORT, CABLE RACK "S" STANDOFF CABLE CABLE RACKS FROM WALL AND CORNER
9/16" x¾” Slot
9/16" Hole
9/16" x ¾” Slot Each End
Stock Code DescriptionK6087 SUPPORT, CORNER CABLE RACK "B"12"X12"K6089 SUPPORT, CORNER CABLE RACK "B" 18"X18"
B
A
C
9/16" X ¾” Slot
9/16"hole
Stock Code Description "A" Dimension "B" Dimension "C" DimensionK6090 BRACKET, "L" 5 1/4 6 9/16 2 3/8
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
109108
UNDERGROUND
UNDERGROUND HARDWARE
4 3/8"
27"
3"
3/8" ROD 1 5/8"
1 1/8"
4 3/8"
7"
3"
3/8" ROD 1 5/8"1 1/8"
K5126 Manhole Hook
K5125 Manhole Hook
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
110
UNDERGROUND
UNDERGROUND HARDWARE
1-1/16"
1-¾”
1-¾”
120°
1-7/8"
K8445 Multi Angle Landing Plate
PAD MOUNTED TRANSFORMER HOLDDOWN WASHER
2"
9/16" SLOTHOLE
5"
3/16"
KXFMRWASHER PAD MOUNTED TRANSFORMER LIP HOLD DOWN WASHER
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
111110
Telephone
TERMINAL BALCONYTerminal BalconyKortick B Terminal Balconies provide a safe working platform 20 inches wide by 18 inches deep with a guard rail to protect the lineman. A step is provided, the hinge platform can be turned upwards to avoid the accumulation of snow or ice. Balcony is fully assembled but collapsed (pictured) for shipping purposes.
K2022 BALCONY, TERM B 12"X18"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
112
TELEPHONE
TELEPHONEStock Code Bell Code Description Long DescriptionK1004CG 400012514 BOLT, CGE 3/8" X 4" WITH OUT NUTK1005CG 400494191 BOLT, CGE 3/8" X 5" WITH OUT NUTK1006CG 400012530 BOLT, CGE 3/8"X6" WITH OUT NUTK1012CG 400012556 BOLT, CGE 3/8" X 12" WITH OUT NUTK1014CG 400012571 BOLT, CGE 3/8" X 14" WITH OUT NUTK1106CG 400012597 BOLT, CGE 1/2 " X 6" WITH OUT NUTK1362 400013785 BOLT, DA 5/8" X 12" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1364 400013793 BOLT, DA 5/8" X 14" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1366 400013801 BOLT, DA 5/8" X 16" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1368 400013819 BOLT, DA 5/8" X 18" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1370 400013827 BOLT, DA 5/8" X 20" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1372 400013835 BOLT, DA 5/8" X 22" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1382 400013850 BOLT, DA 3/4" X 12" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1384 400013868 BOLT, DA 3/4" X 14" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1386 400013876 BOLT, DA 3/4" X 16" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1388 400013884 BOLT, DA 3/4" X 18" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1390 400013892 BOLT, DA 3/4" X 20" W/ 4 ASSY SQUARE NUTS. CHAMFER TIPK1428 400017000 BRACE, XARM FLAT, 28" 9/16" & 7/16 HOLES, 1/4X1-1/4 K1553 400285698 WASHER, SQUARE 2 1/4, FOR 3/4"K1555 400314894 WASHER, SQUARE 3", FOR 3/4K1556 400285706 WASHER, SQUARE 3 1/2X 7/8K1559 400285714 WASHER, SQUARE 4" FOR 1"K1561 400285722 WASHER, SQUARE 6" FOR 1"K1594 400285011 WASHER, SQ CURVE 3 1/4 FOR3/4"K1596 400285029 WASHER, SQ CURVE 3-1/2" 1"K2022 BALCONY SEE PAGE 111K3111 400162913 NUT, THIMBLE, 5/8K3112 400162921 NUT THIMBLE, 3/4K3121 OO2746647 NUT, TWINEYE, 3/4K3216 400013272 BOLT, ST THIMBLEYE 5/8" X 10"K3217 400013280 BOLT, ST THIMBLEYE 5/8" X 12"K3218 400013298 BOLT, ST THIMBLEYE 5/8" X 14"K3220 400013306 BOLT, ST THIMBLEYE 5/8" X 16"K3237 400013348 BOLT, ST THIMBLEYE 3/4" X 12"K3237 400013330 BOLT, ST THIMBLEYE 3/4" X 14"K3256 400012795 BOLT, BENT THIMBLEYE 5/8" X10"K3257 400012803 BOLT, BENT THIMBLEYE 5/8" X 12K3258 400012811 BOLT, BENT THIMBLEYE 5/8" X14"K3260 400012829 BOLT, BENT THIMBLEYE 5/8" X16"K3277 400012852 BOLT, BENT THIMBLEYE, 3/4"X12"K3278 400012860 GUY BOLT, BENT 3/4X14K3280 400012878 GUY BOLT, BENT 3/4X16K3281 400012886 GUY BOLT, BENT 3/4X18K4552 400162095 PLATE LAG ASSEMBLYK4553 400270377 STEP, POLE "B" DETACHABLEK4570 401423876 STEP, POLE, COMBINATIONKTEL10010 BRACE, "F" XARM L4621KTEL10020 BRACE, STL LS237-1KTEL10070 BRACKET, EAVE T L-4601KTEL10080 400314548 HOOK, GUARD ARM AT-6105KTEL10110 400003349 SAME AS K4570KTEL10120 BRACKET, "P" L4580KTEL10130 400272340 STRAP, U- WALLKTEL10140 400272332 PLATE, STP WALLKTEL10141 BRACKET, ANGLE 67A-19"KTEL10142 BRACKET, ANGLE, 23"KTEL10190 401402904 TREE HOOKKTEL10200 CLAMP, CROSSOVER, 1/4"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
113112
TELEPHONE
TELEPHONEStock Code Bell Code Description Long DescriptionKTEL1208 400013645 BOLT, MACHINE 5/8" X 8" ASSY W/(2) SQ NUTKTEL1210 400013652 BOLT, MACHINE 5/8" X 10" ASSY W/(2) SQ NUTKTEL1212 400013660 BOLT, MACHINE 5/8" X 12" ASSY W/(2) SQ NUTKTEL1214 400013678 BOLT, MACHINE 5/8" X 14" ASSY W/(2) SQ NUTKTEL1216 400013686 BOLT, MACHINE 5/8" X 16" ASSY W/(2) SQ NUTKTEL1218 400013694 BOLT, MACHINE 5/8" X 18" ASSY W/(2) SQ NUTKTEL1220 400013702 BOLT, MACHINE 5/8" X 20" ASSY W/(2) SQ NUTKTEL1222 400013710 BOLT, MACHINE 5/8" X 22" ASSY W/(2) SQ NUTKTEL1224 400314274 BOLT, MACHINE 5/8" X 24" ASSY W/(2) SQ NUTKTEL1312 400013736 BOLT, MACHINE 3/4" X 12" ASSY W/(2) SQ NUTKTEL1314 400013744 BOLT, MACHINE 3/4" X 14" ASSY W/(2) SQ NUTKTEL1316 400013751 BOLT, MACHINE 3/4" X 16" ASSY W/(2) SQ NUTKTEL1318 400013769 BOLT, MACHINE 3/4" X 18" ASSY W/(2) SQ NUT
For mor information: sales@kortick.com 510-856-3600
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
114
MARINE
MARINE
STOCK CODE DESCRIPTIONKMAR10020 5/8" x 6"KMAR10030 5/8" x 8"KMAR10035 5/8" x 10"KMAR10040 5/8" x 12"KMAR10050 3/4" x 12"KMAR10060 5/8" x 14"
Sq. Nut
STOCK CODE DESCRIPTIONKMAR10070 PILE GUARD 14"KMAR10080 PILE GUARD 16"KMAR10090 PILE GUARD 18"KMAR10100 PILE GUARD 20"
3"
9-½”
8"
1"
13/16" HOLE(2)9/16"
SLOT(2)
3"
3"
¼” x 3" FLAT BAR
STOCK CODE DESCRIPTIONKMAR10180 PILE ROLLER BRACKET
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
115114
Marine
MARINEMARINE
SQUARE HOLE(4)
STOCK CODE DESCRIPTIONKMAR10110 FRAMING ANGLE
STOCK CODE DESCRIPTIONKMAR10190 WHEEL PLATE
STOCK CODE DESCRIPTIONKMAR10220 FINGER “A” BRACE
2 ¾”
5/16"
5/8" BOLT SIZE DIAMETER
K1525MI WASHER, MALLEABLE IRON 5/8"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
116
CONSTRUCTION
K
“K” marking on Head
Ø “A”
“B”
NOTES:1. ASTM A307 AND HOT DIP GALVANIZED TO ASTM SPECIFICATIO A1532. COARSE THREADED TO CLASS 2 FIT3. DOES NOT INCLUDE HEX NUTS OR WASHERS4. THREAD LENGTH: 2*”A”+½”
Hex BoltsASTM A307 and Hot Dip Galvanized ASTM 153.Bolts are Coarse Threaded to a class 2 Fit. Hex Nuts and washers used on these bolts should be ordered separately.Grade 5, silicon bronze, and stainless steel available upon request, please inquire.Custom thread lengths and assemblies are available; please inquire for standard thread length chart.Please see pages 10-11 for standard sizes
CONSTRUCTION
Kortick Construction Fasteners AvailablePlease call 510-856-3600 or email sales@kortick.com for additional information on Kortick’s fastener stock including:
Penta HeadHex Head (See page 10-11 for stock code information)Carriage Head ( See Page 12 for stock code information)Square HeadCap Screws
Penta NutsHex nutsSquare Nuts
Stainless SteelZinc PlatedSilicon BronzeUncoated
A325Grade 5Grade 8
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
117116
Kortick Anchor Bolts Anchor Bolts are set up in cement for construction uses. Undersize and full sizes are both available.
CONSTRUCTION
ANCHOR BOLTS
“D”
ROUNDWASHERS x2
“L”
“H”
“T”
REG HEX NUTS x2
"D" "L" "H" "T"STOCK NO. (DIA) (LENGTH) (HEIGHT) (THREAD) WASHERK8389 3/4" 17" 3" 6" REGK8390 1" 36" 4" 6" REGK8391 1-1/8" 44" 4" 6" REGK8392 1-1/2" 54" 6" 7" REGK8393 1-3/4" 60" 6" 8" REGK8394 2" 66" 6" 8" REG
K8388-5810 5/8" 10" 1" 4" REGK8388-5818 5/8" 18" 4" 6" REGK8389-18-4 3/4" 18" 4" 6" REGK8389-24 3/4" 24" 3" 6" REGK8390A 1" 36" 4" 6" STD HEXK8390B 1" 36" 4" 6" FULL SIZE, HVY HEX
NOTE:ALL PARTS GALVENIZED PER LATEST ASTM SPECS
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
118
FABRICATION
SUBSTATION STRUCTURESSubstation StructuresPlease inquire for additional information. Kortick fabricates a wide range of substation structure equipment. (CCVT Pedestals pictured)
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
119118
FABRICATION
STATIC WIRE GOAT PEAKSOPGW, Static Wire, AKA: Goat Peaks Kortick OPGW Static Wire Goat Peaks are installed on transmission towers and available in varying designs; please inquire for additional information and capabilities. (9’ and 18’ Goat Peak reflected in drawings. Part numbers available upon request.)
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
120RUS APPROVALSRUS APPROVALS
K-236 STAPLE, CU 3" X 1-1/8" X1/4 K1364 BOLT, DA 5/8" X 14"K-247 STAPLE, CU 1-1/2" X 3/8" X .16 K1366 BOLT, DA 5/8" X 16"K-250 STAPLE, GALV 1-1/2" X 3/16" X K1368 BOLT, DA 5/8" X 18"K-508 INS, SPOOL 2", 1-3/8" K1370 BOLT, DA 5/8" X 20"K-516 INS, SPOOL ANSI 53-2 K1374 BOLT, DA 5/8" X 24"K-522 INS, SPOOL ANSI 53-4 K1390 BOLT, DA 3/4" X 20"K1034 SCREW, LAG FD PP 3/8" X 4" K1392 BOLT, DA 3/4" X 22"K1044-1/2CG BOLT, CGE 3/8" X 4-1/2" K1394 BOLT, DA 3/4" X 24"K1054 NUT, SQ 1/2" K1428 BRACE, XARM FLAT, 28"K1055 NUT, SQ 5/8" K1430 BRACE, XARM FLAT 30"K1056 NUT, SQ 3/4" K1454 PLATE, DOUBLE ARMING C5844K1058 NUT, SQ 1" K1522 WASHER, ROUND FLAT 3/8"K1065 NUT, LOCK MF 3/8" K1523 WASHER, ROUND 3/8"K1066 NUT, LOCK MF 1/2" K1524 WASHER, ROUND FLAT 1/2"K1067 NUT, LOCK MF 5/8" K1525 WASHER, ROUND 5/8"K1068 NUT, LOCK MF 3/4" K1550 WASHER, SQUARE 2", FOR 1/2"K1069 NUT, LOCK MF 7/8" K1553 WASHER, SQUARE 2-1/4" FOR 3/4"K1078 NUT, PAL 3/8" K1555 WASHER, SQUARE 3" FOR 3/4"K1080 NUT, PAL 1/2" K1557 WASHER, SQUARE 4" FOR 3/4"K1081 NUT, PAL 5/8" K1564 WASHER, SQUARE 4" FOR 3/4"K1082 NUT, PAL 3/4" K1570 WASHER, SQUARE 2 1/4" FOR 5/8"K1105 BOLT, MACHINE 1/2" X 5" K1591 WASHER, SQ CURVE 2 1/2" FOR5/8K1106 BOLT, MACHINE 1/2 " X 6" K1592 WASHER, SQ CURVE 3" FOR 3/4"K1107 BOLT, MACHINE 1/2" X 7" K1593 WASHER, SQ CURVE 3" FOR 1"K1108 BOLT, MACHINE 1/2" X 8" K1756 BOLT, MACHINE 7/8" X 6"K1109 BOLT, MACHINE 1/2" X 9" K1757 BOLT, MACHINE 7/8" X 7"K1110 BOLT, MACHINE 1/2" X 10" K1758 BOLT, MACHINE 7/8" X 8"K1112 BOLT, MACHINE 1/2" X 12" K1760 BOLT, MACHINE 7/8" X 10"K1114 BOLT, MACHINE 1/2" X 14" K1762 BOLT, MACHINE 7/8"X12"K1116 BOLT, MACHINE 1/2" X 16" K1764 BOLT, MACHINE 7/8" X 14"K1118 BOLT, MACHINE 1/2" X 18" K1766 BOLT, MACHINE 7/8" X 16"K1120 BOLT, MACHINE 1/2" X 20" K1768 BOLT, MACHINE 7/8" X 18"K1124 BOLT, MACHINE 1/2"X24" K1770 BOLT, MACHINE 7/8" X 20"K1205 BOLT, MACHINE 5/8" X 5" K1772 BOLT, MACHINE 7/8" X 22"K1206 BOLT, MACHINE 5/8" X 6" K1774 BOLT, MACHINE 7/8" X 24"K1207 BOLT, MACHINE 5/8" X 7" K1776 BOLT, MACHINE 7/8" X 26"K1208 BOLT, MACHINE 5/8" X 8" K1812 BRACE, ANGLE 42" X 12"K1209 BOLT, MACHINE 5/8" X 9" K1815 BRACE, ANGLE 60"X18"K1210 BOLT, MACHINE 5/8" X 10" K1932 BRACE, VERT 50"K1212 BOLT, MACHINE 5/8" X 12" K1951 BRACE, ALLEY XARM 5'K1214 BOLT, MACHINE 5/8" X 14" K1954 BRACE, ALLEY XARM 7'K1216 BOLT, MACHINE 5/8" X 16" K1976 BRACE, SIDEARM ANGLEK1218 BOLT, MACHINE 5/8" X 18" K1994 BRACE, BACK EXTENSIONK1220 BOLT, MACHINE 5/8" X 20" K2377 BOLT, OVALEYE & WEDGEK1222 BOLT, MACHINE 5/8" X 22" K2558 BOLT, SHOULDER EYE 5/8"X8"K1224 BOLT, MACHINE 5/8" X 24" K2560 BOLT, SHOULDER EYE 5/8"X10"K1235 SCREW, LAG FD 5/8" X 5" K2562 BOLT, SHOULDER EYE 5/8"X12"K1306 BOLT, MACHINE 3/4" X 6" K2564 BOLT, SHOULDER EYE 5/8"X14"K1307 BOLT, MACHINE 3/4" X 7" K2566 BOLT, SHOULDER EYE, 5/8"X16"K1308 BOLT, MACHINE 3/4" X 8" K2568 BOLT, SHOULDER EYE 5/8" X 18"K1310 BOLT, MACHINE 3/4" X 10" K2570 BOLT, SHOULDER EYE 5/8" X 20"K1312 BOLT, MACHINE 3/4" X 12" K2602 BOLT, DA OVALEYE 5/8" X 14"K1314 BOLT, MACHINE 3/4" X 14" K2603 BOLT, DA OVALEYE 5/8" X 16"K1316 BOLT, MACHINE 3/4" X 16" K2604 BOLT, DA OVALEYE 5/8" X 18"K1318 BOLT, MACHINE 3/4" X 18" K2605 BOLT, DA OVALEYE 5/8" X 20"K1320 BOLT, MACHINE 3/4" X 20" K2616 BOLT, DA OVALEYE 3/4" X 16"K1322 BOLT, MACHINE 3/4" X 22" K2618 BOLT, DA OVALEYE 3/4" X 20"K1324 BOLT, MACHINE 3/4" X 24" K2621 BOLT, DA OVALEYE 3/4" X 26"K1326 BOLT, MACHINE 3/4" X 26" K2678 BOLT, OVALEYE 5/8"X6"K1362 BOLT, DA 5/8" X 12" K2680 BOLT, OVALEYE 5/8"X8"
K2681 BOLT, OVALEYE 5/8"X10"
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
121120 RUS APPROVALSRUS APPROVALS
K2682 BOLT, OVALEYE 5/8"X12" K3458 ROD, ANCHOR TWINEYE 3/4"X8'K2684 BOLT, OVALEYE 5/8"X14" K3459 ROD, ANCHOR TWINEYE 3/4"X9'K2685 BOLT, OVALEYE 5/8"X16" K3460 ROD, ANCHOR TWINEYE 3/4" X 10'K2686 BOLT, OVALEYE 5/8" X 18" K3470 ROD, ANCHOR TWINEYE 1" X 10'K2687 BOLT, OVALEYE 5/8"X20" K3511 PLATE, LOAD 2-HOLE 2-1/2" X 7"K2703 BOLT, OVALEYE 3/4" X 8" K3517 PLATE, LOAD 3-HOLE 2-1/2" X 7"K2704 BOLT, OVALEYE 3/4" X 10" K3527 ROD, ANCHOR TWINEYE 5/8" X 7'K2705 BOLT, OVALEYE 3/4" X 12" K3528 ROD, ANCHOR TWINEYE 5/8"X8'K2706 BOLT, OVALEYE 3/4" X 14" K4005 CLAMP, GUY 3 BOLTK2707 BOLT, OVALEYE 3/4" X 16" K4031 HOOK, GUY 1-BOLTK2708 BOLT, OVALEYE 3/4" X 18" K4035 ATTACHMENT, GUY 1-HOLEK2709 BOLT, OVALEYE 3/4" X 20" K4063 THIMBLE, GUY 5/8" OPEN PATTERNK2909 WASHER, SPRING CLIP 5/8" K4121 CLAMP, BONDING/GROUNDINGK3111 EYENUT, THIMBLEYE 5/8" K4124 CLAMP, GUY 3 BOLTK3112 EYENUT, THIMBLEYE 3/4" K4212 NUT, OVALEYE 5/8"K3113 EYENUT, THIMBLEYE 1" K4252 STEP, POLE 5/8"X10"K3140 EYELET, ANGLE THIMBLE 5/8" K4333 CLAMP, ST SUSP 3B 5/8"K3149 CLAMP, BONDING, GUY ROD TRIPLE K4335 STRAP, REINFORCINGK3160 BOLT, BENT THIMBLEYE 1" X 10" K4344 CLAMP, CABLE SUSP 3-BOLTK3161 BOLT, BENT THIMBLEYE 1" X 12" K4360 PLATE, DBL. SUPPORTK3162 BOLT, BENT THIMBLEYE 1" X 14" K4413 EYELET, STANDARD 5/8"K3164 BOLT, BENT THIMBLEYE 1" X 16" K4552 PLATE, LAG ASSEMBLYK3165 BOLT, BENT THIMBLEYE 1" X 18" K4553 STEP, POLE "B" DETACHABLEK3166 BOLT, BENT THIMBLEYE 1" X 20" K4761 BOLT, DBL. UPSET 5/8" X 8"K3215 BOLT, ST THIMBLEYE 5/8" X 8" K4762 BOLT, DBL. UPSET 5/8" X 9"K3216 BOLT, ST THIMBLEYE 5/8" X 10" K4763 BOLT, DBL. UPSET 5/8" X 10"K3217 BOLT, ST THIMBLEYE 5/8" X 12" K4951 BOLT, SINGLE UPSET 5/8" X 10"K3236 BOLT, ST THIMBLEYE 3/4" X 10" K7104 PIN, INS 5"U- 5 3/4"D-1"LEADK3237 BOLT, ST THIMBLEYE 3/4" X 12" K7122 PIN, INS 5"U - 1- 1/2"D - 1"LEK3254 BOLT, BENT THIMBLEYE 5/8" X 6" K7611 PIN, INS HV 7"U - 7"D - 1 3/8"K3256 BOLT, BENT THIMBLEYE 5/8" X10" K7617 PIN, INS HV 7"U - 7"D - 1-3/8"K3257 BOLT, BENT THIMBLEYE 5/8" X 12 K7631 PIN, INS 6"U 1 3/4" D 1 3/8" LK3275 BOLT, BENT THIMBLEYE, 3/4"X8" K7643 PIN, INS HV 10"U, 7"DK3276 BOLT, BENT THIMBLEYE, 3/4"X10" K8076 PIN, INS POLE TOP - 15" - 1" LK3277 BOLT, BENT THIMBLEYE, 3/4"X12" K8079 PIN, INS POLE TOP - 18" - 1" LK3307 ROD, ANCHOR THIMBLEYE 1/2"X7' K8087 PIN, INS POLE TOP - 24" - 1-3/K3316 ROD, ANCHOR THIMBLE 5/8" X 6' K9109 CLEVIS, W/K516 SPOOLK3317 ROD, ANCHOR THIMBLEYE 5/8"X7' K9172 CLEVIS, THIMBLEK3318 ROD, ANCHOR THIMBLEYE 5/8 X 8 K9259 CLEVIS, IRON ONLY FOR K9109K3328 ROD, ANCHOR THIMBLEYE 3/4"X8' K9278 CLEVIS, IRON ONLYK3330 ROD, ANCHOR THIMBLEYE 3/4"X10' K9280 CLEVIS, IRON ONLYK3338 ROD, ANCHOR THIMBLEYE 1" X 8'
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
122ALPHABETICAL INDEXDESCRIPTION PAGE #ANCHORING, GUY HOOK & POLE EYE 41ANCHORING, PISA ROD 37ANTI CLIMBING DEVICE 102BOLT, ANCHOR 117BOLT, CARRIAGE 12BOLT, DA OVALEYE 33BOLT, DOUBLE ARMING 13BOLT, HEX 10BOLT, MACHINE 8BOLT, MACHINE 9BOLT, OVALEYE 32BOLT, SHOULDER CURVED 31BOLT, SHOULDER EYE 30BOLT, THIMBLEYE BENT 38BOLT, THIMBLEYE STRAIGHT 38BRACE, ALLEY CROSSARM 76BRACE, ANGLE CROSSARM 74BRACE, BACK 80BRACE, CROSSARM VERTICAL 78BRACE, FLAT CROSSARM 75BRACE, GUARD ARM 81BRACE, MISCELLANEOUS 81BRACE, ROUND CROSSARM 81BRACKET, END OF ARM 97BRACKET, MISCELLANEOUS 64BRACKET, MISCELLANEOUS 111BRACKETS, HARDWOOD 65CLEVIS BRACKETS 60CLEVIS, CLEVIS NUT 98CLEVIS, IRON ONLY 57CLEVIS, MISC 57CLEVIS, STRAIN 58CLEVIS, WITH SPOOL 56CLEVIS, WITH SPOOL 57CLEVIS, WITH SPOOL 58CLEVIS, WITH SPOOL 59CLEVIS, WITHOUT SPOOL 59CONDUIT STAND OFF BRACKET 96CONSTRUCTION 116CROSSARM ASSEMBLIES 83CROSSARM REINFORCE SHEARPLATES 28CROSSARM REINFORCING HARDWARE 87CROSSARM, HARDWOOD 85CROSSARM, STEEL 82CUTOUT/ARRESTER BRACKETS 88DOUBLE ARMING PLATE 87EXTENSION BRACKET 63EXTENSION LINK 99EYELET, ANGLE THIMBLEYE 35EYELET, STANDARD 34EYELETS, THIMBLE 35EYENUT 36EYENUT, OVAL 34FABRICATION, GOAT PEAKS 119FABRICATION, SUBSTATION 118GUY PLATE, LOAD & LIFT 39GUY, DEAD END 43INSULATOR BRACKET, HORIZONTAL 93INSULATOR BRACKET, VERTICAL 91
DESCRIPTION PAGE #INSULATOR BRACKET, VERTICAL 92LADDER, EDISON STYLE 104LADDER, TELE STYLE 103LANDING PLATE, MULTI-ANGLE 110MARINE 114NAIL, DATING 18NUT, HEX 19NUT, M-F 20NUT, SQUARE 19OVALEYE SCREW 16PINS, DISTRIBUTION INSULATOR 66PINS, INSULATOR CLEARANCE 71PINS, INSULATOR POLE TOP 70PINS, TRANSMISSION INSULATOR 68PLATE, POLE EYE 42PLATES, LOAD LIFTING AND GUYING 87POLE BAND, 3 PIECE FORGED 45POLE BAND, DOUBLE CUP 44POLE BAND, FOUR WAY 46POLE BAND, SINGLE CUP 44POLE GAINS 86POLE STEP, FIBERGLASS POLES 51POLE STEP, WOOD POLES 50POLE STEP, WOOD POLES 52POLE TOP EXTENSION 101SCREW, ADJUSTING 18SCREW, SQUARE FETTER DRIVE 17SCREW, WASHER HEAD 17SECONDARY RACKS 61SECONDARY RACKS 62SERVICE HARDWARE 53SERVICE HARDWARE 54SERVICE HARDWARE 55SIDEWALK GUY FITTINGS 40STUBBING BAND 48STUBBING BAND 49STUD, POST INSULATOR 72STUD, POST INSULATOR 73TELEPHONE 112TELEPHONE 113THIMBLEYE SCREW 16TRANSFORMER BRACKETS 27TRANSFORMER BRACKETS 94TRANSFORMER BRACKETS 95UNDERGROUND, BRACKET 108UNDERGROUND, CABLE RACK HOOKS 106UNDERGROUND, CABLE RACK HOOKS 109UNDERGROUND, CABLE RACK SUPPT 108UNDERGROUND, MANHOLE STEPS 106UNDERGROUND, PULLING IN IRONS 107UNDERGROUND, RACKS 105WASHER, ANGLE PIN 27WASHER, BEVEL 26WASHER, CENTERING 27WASHER, LIP 25WASHER, LOCK 22WASHER, LOCK DBL COIL 22WASHER, PAD MOUNTED XFRMR HOLD DOWN 110WASHER, ROUND 22WASHER, ROUND MI 23
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
123122 ALPHABETICAL INDEX
DESCRIPTION PAGE #WASHER, ROUND MI 115WASHER, SPRING CLIP 26WASHER, SQUARE 24WASHER, SQUARE CURVED 24WASHER, SQUARE CURVED HC 25
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
124INDEX BY STOCK CODESTOCK CODE PAGE #AK8425BRKT 88AK8425CHANNEL 88ASSEMBLIES 83CONSTRUCTION 116DEAD END TEE 43GOAT PEAKS 119HARDWOOD BRACKETS 65HEAVY DUTY EXTENSION LINKS 99K1000-3/4H 10K1001-1/2 8 ,9K1001-1/4H 10K1001-3/4H 10K1001H 10K1002-1/2H 10K1002H 10K1003-1/2H 10K1003CG 12K1003H 10K1004-1/2 8 ,9K1004-1/2CG 12K1004-1/2H 10K1004CG 12K1004H 10K1005 8 ,9K1005-1/2 8 ,9K1005-1/2CG 12K1005-1/2H 10K1005CG 12K1005H 10K1006 8 ,9K1006-1/2H 10K1006CG 12K1006H 10K1007 8 ,9K1007-1/2H 10K1007H 10K1008 8 ,9K1008-1/2H 10K1008-3/8H 10K1009 8 ,9K1009-1/2H 10K1009H 10K1010-1/2H 10K1010H 10K1011H 10K1012-1/4H 10K1012-13H 10K1012-14H 10K1012-15H 10K1012-16H 10K1012-17H 10K1012-18H 10K1012CG 12K1012H 10K1013H 10K1014-1/2H 10K1014-1/4H 10
STOCK CODE PAGE #K1014-3/4H 10K1014CG 12K1014H 10K1015-1/2H 10K1015H 10K1016-1/2H 10K1016H 10K1017-1/2H 10K1017H 10K1018-1/2H 10K1018H 10K1019-1/2H 10K1019H 10K1020-10-1/2H 10K1020-10H 10K1020-11H 10K1020-12H 10K1020H 10K1051 19K1053 19K1054 19K1055B 19K1056B 19K1057 19K1065 20K1066 20K1067 20K1068 20K1069 20K1070 20K1100H 10K1101 8 ,9K1101-1/2 8 ,9K1101-1/2H 10K1101-1/4H 10K1101-3/4HG 10K1101H 10K1102 8 ,9K1102-1/2HZ 10K1102-1/4 8 ,9K1102-1/4SS 10K1102-3/4H 10K1102H 10K1103 8 ,9K1103-1/2H 10K1103-1/4H 10K1103-3/4H 10K1103H 10K1104 8 ,9K1104-1/2 8 ,9K1104-1/2CG 12K1104-1/2H 10K1104CG 12K1104H 10K1105 8 ,9K1105-1/2H 10K1105CG 12K1105H 10K1106 8 ,9
STOCK CODE PAGE #K1106-1/2H 10K1106CG 12K1106H 10K1107 8 ,9K1107-1/2H 10K1107CG 12K1107H 10K1108 8 ,9K1108-1/2H 10K1108CG 12K1108H 10K1109 8 ,9K1109-1/2H 10K1109H 10K1110 8 ,9K1110-1/2H 10K1110H 10K1111-1/2H 10K1111H 10K1112 8 ,9K1112CG 12K1112H 10K1113H 10K1114 8 ,9K1114H 10K1115H 10K1116 8 ,9K1118 8 ,9K1118H 10K1120 8 ,9K1122 8 ,9K1122-24 8 ,9K1157 17K1159ADJ 18K1159ADJB 18K1201-1/2H 10K1201-1/4H 10K1201-3/4 8 ,9K1201-3/4H 10K1201H 10K1202 8 ,9K1202-1/2 8 ,9K1202-1/2H 10K1202-1/4H 10K1202H 10K1203 8 ,9K1203-1/2H 10K1203-1/4H 10K1203H 10K1204 8 ,9K1204-1/2H 10K1204H 10K1205 8 ,9K1205-1/2H 10K1205H 10K1206 8 ,9K1206-1/2H 10K1206H 10K1207 8 ,9
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
125124 INDEX BY STOCK CODESTOCK CODE PAGE #K1207-1/2H 10K1207H 10K1208 8 ,9K1208-1/2H 10K1208HB 10K1209 8 ,9K1209-1/2H 10K1209CG 12K1209H 10K1210 8 ,9K1210-1/2H 10K1210H 10K1211-1/2H 10K1211H 10K1212 8 ,9K1212H 10K1213H 10K1214 8 ,9K1214H 10K1215H 10K1216 8 ,9K1216H 10K1217H 10K1218 8 ,9K1218H 10K1220 8 ,9K1220H 10K1222 8 ,9K1224 8 ,9K1226 8 ,9K1228 8 ,9K1230 8 ,9K1230-32 8 ,9K1230-34 8 ,9K1230-36 8 ,9K1230-38 8 ,9K1230-40 8 ,9K1230-42 8 ,9K1230-44 8 ,9K1230-46 8 ,9K1230-48 8 ,9K1230-50 8 ,9K1230-52 8 ,9K1230-54 8 ,9K1254 22K1254DC 22K1255 22K1255DC 22K1256 22K1256DC 22K1257 22K1257DC 22K1258 22K1259 22K1265 19K1267 19K1268 19K1269 19K1270 19
STOCK CODE PAGE #K1271 19K1272 19K1273 19K1300H 11K1301-1/2H 11K1301-1/4H 11K1301-3/4H 11K1302 8 ,9K1302-1/2 8 ,9K1302-1/2H 11K1302-3/4H 11K1302H 11K1303 8 ,9K1303-1/2H 11K1303-1/4H 11K1304-1/2H 11K1304H 11K1305-1/2H 11K1305H 11K1306-1/2H 11K1306H 11K1307-1/2H 11K1307H 11K1308-1/2 8 ,9K1308-1/2H 11K1308H 11K1309-1/2H 11K1309H 11K1310 8 ,9K1310H 11K1311H 11K1312 8 ,9K1312H 11K1313H 11K1314 8 ,9K1314H 11K1315H 11K1316 8 ,9K1316H 11K1317H 11K1318 8 ,9K1318H 11K1320 8 ,9K1320H 11K1322 8 ,9K1322H 11K1324 8 ,9K1324H 11K1326 8 ,9K1326H 11K1328 8 ,9K1328H 11K1330 8 ,9K1332 8 ,9K1332H 11K1338 8 ,9K1342 8 ,9K1362 13K1364 13
STOCK CODE PAGE #K1366 13K1368 13K1370 13K1372 13K1374 13K1376 13K1378 13K1380 13K1380-32 13K1380-34 13K1380-36 13K1380-38 13K1380-42 13K1380-44 13K1380-48 13K1380-54 13K1382 13K1384 13K1386 13K1388 13K1390 13K1392 13K1394 13K1396 13K1398 13K1400-30 13K1400-32 13K1400-34 13K1400-36 13K1400-38 13K1400-40 13K1400-42 13K1400-44 13K1412 75K1420 75K1422 75K1424 75K1426 75K1428 75K1430 75K1432 75K1436 75K1521 22K1521-1/2 22K1522 22K1523 22K1524 22K1525 22K1525MI 23K1526 22K1527 22K1528 22K1528-1-3/4 22K1547-1/2 26K1547-5/8 26K1550 24K1551 24K1553 24K1554 24
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
126INDEX BY STOCK CODESTOCK CODE PAGE #K1557 24K1558 24K1559 24K1561 24K1562 24K1570 24K1582 24K1582HC 25K1590 24K1591 24K1592 24K1592HC 25K1594 24K1596 24K1597 24K1597-1/4 24K1597HC 25K1615 27K1630 27K1632 27K1645 25K1646 25K1682 17K1683 17K1684 17K1702-1/2H 11K1704-1/2H 11K1705H 11K1706-1/2H 11K1707-1/2H 11K1707H 11K1708-1/2H 11K1709-1/2H 11K1709H 11K1710H 11K1711H 11K1712H 11K1714H 11K1716H 11K1718H 11K1720 75K1722 75K1724 75K1726 75K1728 75K1730 75K1734 75K1762 8 ,9K1764 8 ,9K1766 8 ,9K1768 8 ,9K1770 8 ,9K1772 8 ,9K1774 8 ,9K1776 8 ,9K1778 8 ,9K1780-42 8 ,9K1811 74K1812 74
STOCK CODE PAGE #K1813 74K1813-1/2 74K1814 74K1815 74K1818 74K1819 74K1820 74K1821 74K1822 74K1872 13K1874 13K1876 13K1878 13K1880 13K1882 13K1884 13K1886 13K1888 13K1890-32 13K1890-34 13K1890-36 13K1890-38 13K1901 81K1951 76K1952 76K1953 76K1954 76K1955 76K1966 76K1984 80K1985 80K1986 80K1987 80K1988 80K-200-11 18K-200-12 18K-200-13 18K-200-14 18K2102H 11K2103-1/2H 11K2103H 11K2104H 11K2105H 11K2157H 11K2158H 11K2159H 11K2160 8 ,9K2160H 11K2162 8 ,9K2162H 11K2164 8 ,9K2164H 11K2166 8 ,9K2166H 11K2168 8 ,9K2168H 11K2170 8 ,9K2170H 11K2172 8 ,9
STOCK CODE PAGE #K2172H 11K2174 8 ,9K2174H 11K2176H 11K2178H 11K2180H 11K2182H 11K2184H 11K2186H 11K2188-50H 11K2188-52H 11K2188-54H 11K2188-56H 11K2188H 11K2190H 11K2192H 11K2194H 11K2232H 11K2233H 11K2234-2-1/2H 11K2234-3H 11K2235-1/2H 11K2236H 11K2237H 11K2238H 11K2409-18 13K2409-20 13K2409-22 13K2409-24 13K2409-26 13K2409-28 13K2409-28DE 14K2409-30DE 14K2409-32 13K2409-32DE 14K2409-34 13K2409-34DE 14K2409-36 13K2409-36DE 14K2409-38 13K2409-38DE 14K2409-40DE 14K2409-42DE 14K2409-44DE 14K2409-46DE 14K2409-48DE 14K2409-50DE 14K2556 30K2556CW 31K2556CW 31K2558 30K2558CW 31K2560 30K2560CW 31K2560CW 31K2562 30K2562CW 31K2562CW 31K2564 30
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
127126 INDEX BY STOCK CODESTOCK CODE PAGE #K2564CW 31K2564CW 31K2566 30K2566CW 31K2566CW 31K2568 30K2568CW 31K2568CW 31K2570 30K2570CW 31K2570CW 31K2572CW 31K2572CW 31K2574CW 31K2574CW 31K2576 30K2576-28CW 31K2576-30CW 31K2576CW 31K2576CW 31K2578 30K2578CW 31K2578CW 31K2580 30K2580CW 31K2580CW 31K2582 30K2582CW 31K2582CW 31K2584 30K2584CW 31K2584CW 31K2586 30K2586CW 31K2586CW 31K2588 30K2588CW 31K2588CW 31K2590 30K2590-22CW 31K2590-24CW 31K2590-26CW 31K2590-28CW 31K2590-30CW 31K2590CW 31K2590CW 31K2595-12CW 31K2595-14CW 31K2596CW 31K2597CW 31K2598CW 31K2601 33K2602 33K2603 33K2604 33K2605 33K2606 33K2607 33K2608 33
STOCK CODE PAGE #K2609 33K2614 33K2615 33K2616 33K2617 33K2618 33K2619 33K2620 33K2621 33K2654 32K2656 32K2658 32K2660 32K2662 32K2664 32K2666 32K2668 32K2678 32K2680 32K2681 32K2682 32K2684 32K2685 32K2686 32K2687 32K2688 32K2689 32K2689-26 32K2689-28 32K2689-30 32K2702 32K2703 32K2704 32K2705 32K2706 32K2707 32K2708 32K2709 32K2710 32K2711 32K2775 16K2776 16K2777 16K2778 16K2780 16K2781 16K2782 16K2908 26K2909 26K2910 26K2910-1/2 26K3110 36K3111 36K3112 36K3113 36K3120 36K3121 36K3122 36K3130 35
STOCK CODE PAGE #K3131 35K3140 35K3141 35K3215 38K3216 38K3217 38K3218 38K3220 38K3222 38K3222-24 38K3222-26 38K3222-28 38K3222-30 38K3235 38K3236 38K3237 38K3238 38K3240 38K3241 38K3242 38K3243 38K3248 38K3249 38K3250 38K3254 38K3255 38K3256 38K3257 38K3258 38K3260 38K3262 38K3264 38K3275 38K3276 38K3277 38K3278 38K3280 38K3281 38K3282 38K3501 39K3503 39K3504 39K3506 39K3510 39K3511 39K3512 39K3514 39K3516 39K3517 39K3518 39K3519 39K3520 39K3521 39K3522 39K3523 39K3524 39K4210 34K4212 34K4213 34
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.comwww.KORTICK.com
128INDEX BY STOCK CODESTOCK CODE PAGE #K4252 50K4252K 50K4258 50K4272 51K4276 51K4307 48 ,49K4309 48 ,49K4310 48 ,49K4311 48K4312 48K4325 86K4328 48 ,49K4411 34K4412 34K4413 34K4414 34K4450 59K4450SP 59K4528 62K4529 62K4547 59K4552 52K4553 52K4570 52K4582 54K4587 71K4593Z 54K4725Z 53K5071 46K5072 46K5108 105K5114 105K5118 105K5120 105K5122 105K5125 109K5126 109K5150 105K5152 105K5153 105K5155 105K5156 105K-516 57 ,58K5160 105K5162 105K5164 105K5165 105K5166 105K5170-43 105K-522 57K-524 56 ,59K5244-1/4 107K5244-1/4SQ 107K5247 107K5247SQ 107K5248 107K5248SQ 107K5251 107K5251SQ 107
STOCK CODE PAGE #K5252 107K5252SQ 107K5255 106K5256 106K5257 106K5258 106K5259 106K-526 56K5261 106K5262 106K5275 103K5276 103K5277 103K5278 103K5279 103K5280 103K5281 103K5282 103K5284 103K5286 103K5288 103K5927-3P-2 53K6085 108K6087 108K6089 108K6090 108K6275 40K6276 40K6277 40K6278 40K6300 94K6303 94K6411 96K6412 96K6413 96K7105Z 66K7106Z 66K7108Z 66K7122 66K7631 69K7770Z 67K7774 68K7774-8 1/2 68K7774Z 68K7784 68K7784Z 68K7788 70K7791Z 67K7793Z 67K7794Z 67K7795Z 67K7796Z 67K8076 70K8079 70K8083 70K8086 70K8087 70K8105 70K8106 70
STOCK CODE PAGE #K8107 70K8108 70K8122 70K8123 70K8124 70K8183 44K8184 44K8185 44K8193 44K8194 44K8195 44K8196 45K8197 45K8198 45K8199 45K8200 45K8202 45K8203 45K8204 45K8204-3/4 45K8205 45K8226 81K8227 81K8228 81K8229 81K8242 61K8242AZ 61K8245 61K8257 91K8257-69 91K8258-10 98K8258-12 98K8258-18 98K8258-24 98K8258-42 98K8259-115 92K8259-69 92K8259PL-115 92K8259PL-115 SPL 92K8295 28K8298 28K8299 28K8300 60K8300SPP 60K8308 76K8309 76K8314 78K8315 78K8316 78K8317 78K8318 78K8319 78K8321Z 71K8323Z 71K8327 64K8341 87K8343 87K8344 87K8345Z 55
MANUFACTURING COMPANYPOLE LINE HARDWARE DROP PRESS-UPSET FORGINGS
2230 Davis Court, Hayward, CA 94545PH. (510) 856-3600 EM. sales@kortick.com
www.KORTICK.com
129128 INDEX BY STOCK CODESTOCK CODE PAGE #K8348 60K8350 95K8351 95K8353 90K8355 98K8358 98K8358CN 98K8359 98K8360 93K8361-1 90K8363 90K8364 72K8365 73K8365-9 73K8365SPL 73K8366 72K8366SPL 72K8371 93K8374 71K8377 89K8379 89K8380 71K8381 63K8388 97K8388-5810 117K8388-5818 117K8389 117K8389-18-4 117K8389-24 117K8390 117K8390A 117K8390B 117K8391 117K8392 117K8393 117K8394 117K8397 55K8398 82K8399 87K8400 79K8401 79K8402 79K8403 79K8406 79K8407 79K8423 60K8425 88K8440 89K8445 110K8510 101K8511 77K8514 97K8516 80K8530 73K8578 104K8579 104K8580 104K8581 104K8582 104
STOCK CODE PAGE #K8583 104K8584 104K8585 104K8586 104K8619 71K9087 57K9088 57K9101 59K9101-5/8 59K9102 56K9104 56K9107 57K9109 58K9116 57K9155 58K9158 58K9164 58K9165 58K9251 59K9252 56K9254 56K9259 58K9291 57KA11200 37KA11210 37KA11875 41KA11900 41KBR10006 93KBR10006-9 93KBR10080 94KIF10180 98KMAR10020 114KMAR10030 114KMAR10035 114KMAR10040 114KMAR10050 114KMAR10060 114KMAR10070 114KMAR10080 114KMAR10090 114KMAR10100 114KMAR10110 115KMAR10180 114KMAR10190 115KMAR10220 115KTEL10010 112KTEL10020 112KTEL10070 112KTEL10080 112KTEL10110 112KTEL10120 112KTEL10130 112KTEL10140 112KTEL10141 112KTEL10142 112KTEL10190 112KTEL1208 113KTEL1210 113KTEL1212 113
STOCK CODE PAGE #KTEL1214 113KTEL1216 113KTEL1218 113KTEL1220 113KTEL1222 113KTEL1224 113KTEL1312 113KTEL1314 113KTEL1316 113KTEL1318 113KWDH10032 85KWDH10045 85KWDH10047 85KWDH10052 85KWDH10055 85KWDH10057 85KXACG-4' 102KXC2110019 27 ,110KXPG44 86KXPG46 86KXPG49 86POLE EYE PLATE 42RM BRACKET K6412SMUD 111SUBSTATION 118
catalog design by shana e. frase