POWER SYSTEMS, INC. CAST IRON POLE LINE …...CAST IRON POLE LINE HARDWARE Warranty - Material...
Transcript of POWER SYSTEMS, INC. CAST IRON POLE LINE …...CAST IRON POLE LINE HARDWARE Warranty - Material...
5A-�
MAY 2006HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
5A
CAST IRONPOLE LINE HARDWARE
Warranty - MaterialHubbell Power Systems, Inc. warrants all products sold by it to be merchantable (as such term is defined in the Uniform Commercial Code) and to be free from defects in material and workmanship. Buyer must notify the Company promptly of any claim under this warranty. The Buyer’s exclusive remedy for breach of this warranty shall be the repair or replacement, F.O.B. factory, at the Company’s option, of any product defective under the warranty which is returned to the Company within one year from the date of shipment. NO OTHER WARRANTY, WHETHER EXPRESS OR ARISING BY OPERATION OF LAW, COURSE OF DEALING, USAGE OF TRADE OR OTHERWISE IMPLIED, SHALL EXIST IN CONNECTION WITH THE COMPANY’S PRODUCTS OR ANY SALE OR USE THEREOF. The Company shall in no event be liable for any loss of profits or any consequential or special damages incurred by Buyer. The Company’s warranty shall run only to the first Buyer of a product from the Company, from the Company’s distributor, or from an original equipment manufacturer reselling the Company’s product, and is non-assignable and non-transferable and shall be of no force and effect if asserted by any person other than such first Buyer. This warranty applies only to the use of the product as intended by Seller and does not cover any misapplication or misuse of said product.
Warranty - ApplicationHubbell Power Systems, Inc. does not warrant the accuracy of and results from product or system performance recommendations resulting from any engineering analysis or study. This applies regardless of whether a charge is made for the recommendation, or if it is provided free of charge.
Responsibility for selection of the proper product or application rests solely with the purchaser. In the event of errors or inaccuracies determined to be caused by Hubbell Power Systems, Inc., its liability will be limited to the re-performance of any such analysis or study.
©Copyright 2006 Hubbell • 210 North Allen Street • Centralia, MO 65240NOTE: Because Hubbell has a policy of continuous product improvement, we reserve the right to change design and specifications without notice.
Minimum order quantities may apply.Contact factory for test information.
Printed in USARGS 15M
5A-�
MAY 2006 HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
AUXILIARY EYES
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Adds additional guy attachment to existing anchor rod. Also can be used as a pulling eye for guying tension.
CatalogNo.
BB155A
Approx. Ship Wt. Lbs.
Per 100 Pcs.270
Anchor RodDiameter
5/8" - 1"
Maximum Strand Size
1/2"
ThimbleDiameter
11/2"
CatalogNo.
† B14A B14B B12A B12B
Approx. Ship Wt. Lbs.
Per 100 Pcs.100100137137
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153Contact factory for round bolt hole design.† RUS Listed
Maximum Strand Size
——
5/8"5/8"
Mounting Bolt Diameter
5/8" 3/4"5/8"3/4"
Slotted hole design to allow thru-bolt to be inserted from eye side. Not threaded.
BOLT EYELETS
Approx. Ship Wt. Lbs.
Per 100 Pcs.
38
Tap
2 STR - 6 SOL
Main9/16" - 1/4"
250 MCM - 4 STR
Cable Range B14
B12
1.50" 1.94"
.56"2.50"
.56"
.56"
1.25"
3.00"
CB1
2.38"
1.25"
4.25"
2.38"
Series CB - Bonding clamps are specified for connecting ground wires to guys, messengers, or static wires.
BONDING CLAMPS
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153; U-Bolts .5" diameter
CatalogNo.
CB1
5A-�
MAY 2006HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
CatalogNo.
ICB1 ICB10
Approx. Ship. Wt. Lbs.
Per 100 Pcs.147262
"A" Dimensions
7 5/8" 12"
Mtg. Bolt Diameter
5/8"5/8"
Equip. Bolt Diameter
3/8"3/8"
Designed to fit NEMA “L” brackets. One bolt mounts bracket to pole.
BRACKET,CUTOUT AND ARRESTER
A
61⁄4"
47⁄8"
11⁄16" DIA.
3⁄8" x 13⁄4" CARRIAGE BOLTTWO PROVIDED
BRACKET, ANGLE CROSSARM
CatalogNo.
1XAB
CrossarmSize
33/4" x 43/4" Max. and
RoundCrossarms
Approx. Ship Wt. Lbs.
Per 100 Pcs.
610
Mtg. BoltDiameter
3/4"
Stud BoltDiameter
3/4"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Mounts post insulators at 30° angle on crossarm for use on running corners.
5A-�
MAY 2006 HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
Mounts post or pin type insulator to top of pole. Variety of bolt hole locations for mounting to pole.
BRACKET,POLE TOP INSULATOR
CatalogNo. IB2 IB3†IB4
Approx. Ship.Wt.Lbs.Per 100 Pcs.
360600600
Mounting Bolt Dia.
5/8" 3/4" 5/8"
Insulator Bolt Dia.5/8" or 3/4"5/8" or 3/4"5/8" or 3/4"
Mtg. Bolt Spacing
43/4"5" or 8"5" or 8"
Dis. From Insul.Base
To Top Hole43/4"63/8"5"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153† RUS Listed
11⁄16"
11⁄16"
43⁄4"
105⁄8"
5"
11⁄16"
41⁄2"
5"
8"
21⁄2"
13⁄16"
23⁄16"
IB4
21⁄2"
3"
13⁄16"
33⁄4"
IB2
33⁄4"
2"
6"
153⁄8"
IB3
3"
63⁄8"
15⁄16"
13⁄16"
14"
5A-5
MAY 2006HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.BRACKET,HORIZONTAL INSULATOR
Use for mounting one or two insulator(s) to pole for armless construction.
Approx. Ship.
Wt.Lbs.Per
100 Pcs.333
1025
Space Between
Insul. Bases
—14"
Insul.AngleDim.
5°—
Mtg. Bolt
Spacing5", 6"4", 5"
Max.Insul.BoltDia. 3/4" 3/4"
Mtg. Bolt Dia.Two 5/8" Two 5/8"
CatalogNo.
1IPTB2IPTB
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
BRACKET,VERTICAL INSULATOR
Use for mounting pin or post vertical insulators, cutouts, arresters, or cable terminators. Three-hole style can be used for in-line deadending using suspension insulators.
2IPTB
Max.Insul.Mtg.Bolt Dia. 3/4" 3/4" 3/4"3/4"3/4"
PoleMtg. Bolt Dia.
Two 5/8" Two 5/8" Two 5/8"Two 5/8"Two 5/8"
Max.Equip.Mtg.Bolt Dia. 5/8"5/8" 5/8"1/2"5/8"
Pole Mtg. Bolt
Spacing5"5"5"5"5"
Clearance Pole To Insul. Bolt"A"12"18"18"12"18"
Approx. Ship.
Wt.Lbs.Per
100 Pcs.860
13001400
861400
4"
4"
4"
"A"
.58 sq. Hole
T2060594
Side view with hardware
LB12A1 & LB18B14" R
41⁄2"
4"
41⁄2"
T2060594
For 3⁄8" Carriage Bolt13⁄16" Dia.
"A"
5"
LB18B3/LB18B3CH
"A"
11⁄16" Dia. Hole
4"
4"
11/4"Catalog
No.LB12A1LB18B1LB18B3
*T2060594**LB18B3CH
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
* T2060594 has 3 captive 1/2" x 2" bolts and nuts included**LB18B3CH has 2 captive 1/2" x 2" bolts and nuts included with LB18B3.
11⁄16" Dia.
4"
1IPTB
5A-�
MAY 2006 HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
CLAMP, U-BOLT GUYCan be easily installed without disassembling the clamp. The GCU38C and GCU50C have a spacer block to help prevent damage to strand against U-bolt.
Approx. Ship Wt. Lbs.Per 100 Pcs.
80
Type of NutHEX
U- Bolt Dia.3/8"
CatalogNo.
GCU38Strand Size
3/16" - 3/8"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
CatalogNo.
ASC2ASC3
Approx. Ship Wt. Lbs.Per 100 Pcs.
175175
MessengerRange
.22" - .56"
.43" - .75"
Pole Clearance
11/2"11/2"
Mounting Bolt Dia.
5/8"5/8"
Rigid keeper for maximum clamping action. Bottom groove is curved to prevent damage to messenger. Top hook to sup-port cable during installation.
CLAMP, AERIAL SUSPENSION
ASC2
ASC5 Heavy duty clamp design uses two bolts to hold messenger to clamp, which prevents clamp slippage if pole shrinks.
CLAMP, AERIAL SUSPENSION
Approx. Ship Wt. Lbs.Per 100 Pcs.
725
MessengerRange
9/16" - 3/4"
Mtg.BoltDia.5/8"
Pole Clear.
3"
GroundWire6 AWG
Catalog No.ASC5
Clamp Bodies and Spacer: Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
GCU38
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
ClampBolt Dia.
Two-5/8"Sq.Hd.
5A-�
MAY 2006HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
Bolts installed in opposite directions to allow greater wrench clearance.
CLAMP, TWO-BOLT GUY
Clamp Lngth.
11/8"
13/16"
TwoClamps
10,700Wire
Broke13,100
Holding Power lbs.
CatalogNo.
GC131
GC138
Guy Strand
Size
5/16"
3/8"
No.Slip
7,300
7,200
Slip Less Than Dia.of Strand
7,700
9,150
Slip Less Than11/2"
9,600
12,150
GCSERIES
Clamp Bodies: Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Approx. Ship Wt. Lbs.
Per 100 Pcs.200
L
5⁄8" Clevis Pin
7⁄8" 13⁄8"
11⁄2" Dia. (Typ)11⁄16" Dia. (Typ)
L14
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
CatalogNo. L14
Pin Diameter
5/8"L - Inches
14
The L14 is a one-piece extension link with a clevis pin and cotter key.
EXTENSION LINK
Approx. Ship Wt. Lbs.Per 100 Pcs.
66
90
5A-�
MAY 2006 HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC. Crossarm Grid Gain
Crossarm Range
31/2" - 51/2"31/2" - 51/2"
5" - 7"5" - 7"41/2"
Approx. Ship Wt. Lbs.Per 100 Pcs.
80130180180120
CatalogNo.
PG31PG441PG45PG45SPG3545
Dimensions In InchesMax. Bolt Dia. "D"
3/43/43/43/45/8
Pole Dia. Range6" - 10"6" - 11"6" - 11"6" - 11"4" - 9"
B44
55/16 51/441/2
A3444
31/2
Curved face with spurs prevents need of cutting gain into pole. Slotted hole for easy alignment.
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Catalog numbers with "S" suffix have extended bolt hole slot.
Flat Back Crossarm Gain
Approx. Ship Wt. Lbs.Per 100 Pcs.
180175120375
CatalogNo.
PG4 PG4A †PG44 PG5
Pole Dia. Range "R"
6" - 11"6" - 11"6" - 11"
10" - 16"
Max. Bolt Dia. "D"
3/47/87/87/8
B51/251/24
71/4
A444
53/8
Dimensions In Inches
Curved face with spurs prevents need of cutting gain into pole. Large surface area reduces crossarm shift.
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153† RUS Listed
Mtg. & Bolt "D"
No. & Dia.
Two - 5/8"
Two - 3/4" Max.
Approx. Ship Wt. Lbs.Per 100 Pcs.
540
950
CrossarmRange
31/2" x 61/2"
4" Channel
Dimensions In Inches
B
35/8
47/16
C
6
8
E
11/16
Dia. Hole
13/16
Dia. Hole
CatalogNo.
PG84XB12
PG84XE12
A
8
93/4
D4"
E
B
C 10"
A
GAIN, SHELFProvides strong, stable crossarm connection to the pole. Reduces need for braces. Deadending or guying located directly under arm. Steel crossarm can be mounted to shelf with bolts.
Clamp Bodies: Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
A
B
D
A
B
D
R
5A-�
MAY 2006HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
Approx. Ship Wt. Lbs.
Per 100 Pcs.6288988898
240225
CatalogNo.
GH151A † GH5 GH5ILS GH6 GH6ILS GH6X GH6XBILS
Max. Guy Strand
Dia.7/16"7/16"7/16"1/2"1/2"5/8"5/8"
Lag Screw Dia.None
1/2"None
1/2"None
1/2" or 3/4"None
GUY HOOKUse in down or span guy applications. Spurs resist down slotting. The overturning action is resisted by the wide lower curved heal pad. Contact Factory about Guy Hooks for use on concrete and steel poles.
Thru-Bolt
Dia. 5/8" 5/8" 5/8" 3/4" 3/4" 7/8" 1"
PIN, ANGLE
CatalogNo.
PS8779 PBA841
Bolt Size
5/8" x 7"5/8" x 7"
Thread Size1"1"
Pin Height Above Arm
5"81/4"
Crossarm Size4"4"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
The crossarm corner pin is made of ductile iron, hot dip galvanized. Made with 1" lead threads for 1" thread insula-tors at an angle 60o from horizontal. Attached to the cros-sarm by means of a square head bolt, which is furnished as part of the pin.
GUY HOOK, SPAN TYPEFor guy attachment, use at angles 0o to 30o from horizontal.
CatalogNo.
GH2GH3
Approx. Ship Wt. Lbs.
Per 100 Pcs.6664
Max. Thru-Bolt Dia.5/8" 3/4"
Max. GuyStrand Dia.
1/2"1/2"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Suffix "ILS" indicates cast in integral lagDuctile iron per ASTM A-536Hot dipped galvanized per ASTM A-153† RUS Listed
41⁄2"25⁄8"
23⁄8"
11⁄2"
15⁄8"
41⁄2"
Bolt 5⁄8" x 7"
GH151AGH5ILS
23⁄4"
33⁄4" 11⁄16" dia.
3⁄8"
27⁄16"
2"
13⁄16" 25⁄8"
9⁄16"
11⁄2"
35⁄8" GH6 15⁄8"
415⁄16"
21⁄2"
GH2
PS8779
Approx. Ship Wt. Lbs.
Per 100 Pcs.315541
5A-�0
MAY 2006 HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
65⁄8"4"
13⁄16" DIA.
41⁄8"
1"
13⁄4"
21⁄32"
4"
51⁄4"
17⁄8"
PLATE, POLE EYEGEP6 style eye plate provides large pad area to spread forces over pole surface. Ideal for guy strain insulator installation.
CatalogNo.
GEP6
Approx. Ship Wt. Lbs.Per 100 Pcs.
269
Mounting Bolt Diameter
3/4"
Maximum Pin Diameter
3/4"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Narrow profile eye plate provides clevis eye with 5/8" maxi-mum pin diameter.
CatalogNo.
GEP5CGEP5DGEP5EGEP5G
Approx. Ship Wt. Lbs.Per 100 Pcs.
155155155155
Max. PinDiameter
5/8"5/8"5/8"5/8"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
PLATE, POLE EYE
PLATE, POLE EYEAllows guy loop to be made up on the ground as well as providing a clevis eye plate capability. Spurs prevent slip-page down the pole. Contact Factory about eye plates for use on concrete and steel poles.
CatalogNo.
GEP5 GEP5A
Approx. Ship Wt. Lbs.Per 100 Pcs.
175175
Mounting Bolt Dia.
5/8"3/4"
Max. Pin Diameter
5/8"5/8"
Max. Strand Size5/8"5/8"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
25⁄8"
11⁄16" Dia.
41⁄2"25⁄8"
31⁄4"
GEP5: 11⁄16" Dia.GEP5A: 13⁄16" Dia.
11⁄16" Dia.
11⁄4"23⁄8"
GEP5
Mounting Bolt Diameter
5/8"3/4"3/4"3/4"
Lag Screw Diameter
1/2"Integral Spur
1/2"3/4"
5A-��
MAY 2006HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
Top curved groove has 3/8" radius to allow guy at-tachment. Groove captures guy attachment against pole to help prevent possibility of guy slipping off hook. Also has pole eye lug.
PLATE, POLE EYE
GEP7GEP12
13⁄16" Dia.
17⁄8"
21⁄2"67⁄16"
23⁄8"
A
11⁄4"313⁄16"
"A"
37⁄8" "A"41⁄4"
13⁄8" R
2"
13⁄4"83⁄8"
POLE BRACEFor use in push pole application where guying is not feasible. Brace adjusts for different pole angles.
CatalogNo.
SG611
Approx. Ship Wt. Lbs.Per 100 Pcs.
750
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Pole Diam-eter
6" - 11"
Hinge Bolt Dia.
3/4"
Mounting Bolt Dia.
3/4"
BaseDiameter
4" x 8"
TWIN ARM SPACER Connects two crossarms in twin arm application. Lugs provide for deadending attachment.
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
"F" Dia.Clevis Pin
"B"
"A""C"
"E"
TC2
THIMBLE CLEVIS, GUY WIRE
Approx. Ship Wt. Lbs.Per 100 Pcs.
100275
Commonly used for attaching guy to pole eye plate. Clevis pin has humped cotter key.
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
CatalogNo.TC1TC2
A49/16 55/16
E3/41
C33/4
45/16
Dimensions In Inches
B 13/4 21/2
F5/83/4
D17/16 13/4
Clearance for 3/4"Sq. Hd. Bolt
"B"
41⁄2"
"A"
97⁄8"21⁄2"
CXS
CatalogNo.
CXS1
Approx. Ship Wt. Lbs.Per 100 Pcs.
440
For Cross- Arm Sizes
31/4" x 41/4" & 4" x 5"
Mtg. BoltHole "A"
11/16"
Clevis Bolt Hole "B"
11/16"
8" 4"
CatalogNo.
GEP7GEP7AGEP12
Max. PinDia.7/8"7/8"3/4"
"A"Mtg.
Bolts No. & Dia.Two 1"Two 7/8"One 7/8"
Ductile iron per ASTM A-536Hot dipped galvanized per ASTM A-153
Approx. Ship
Wt. Lbs.Per 100 Pcs.
559564332
6"
"D"
5A-��
MAY 2006 HUBBELL / CHANCE – CENTRALIA, MISSOURI
®®
POWER SYSTEMS, INC.
Approx. Ship Wt. Lbs.Per 100 Pcs.
204545
100100
Size Inches
*21/4 x 21/4*3 x 3*3 x 3*4 x 4 4 x 4
CatalogNo.
GCW1†GCW31GCW31A†GCW41GCW41A
Thickness At BossInches
1/43/83/81/2
17/32
Max.Bolt Dia.Inches
5/85/83/43/47/8
C U R V E D S Q U A R E
Cast washers provide excellent strength characteristics. Reinforcing ribs helps prevent washer from crushing.
WASHERS, CAST
GCW
† RUS Listed* NEMA Standard
Approx. Ship Wt. Lbs.Per 100 Pcs.
459393
Size Inches
*21/4 x 31/2*3 x 4 3 x 4
CatalogNo.
CRW3†CRW4ACRW4B
Thickness At BossInches
3/81/21/2
Max.Bolt Dia.Inches
3/47/81
C U R V E D R E C T A N G U L A R
† RUS Listed* NEMA Standard
Approx. Ship Wt. Lbs.Per 100 Pcs.
2020
Size Inches
*21/4 x 21/4*21/4 x 21/4
CatalogNo.
†BB214BB214A
Thickness At BossInches
9/329/32
Max.Bolt Dia.Inches
5/83/4
S Q U A R E F L A T
† RUS Listed* NEMA Standard
Approx. Ship Wt. Lbs.Per 100 Pcs.
448787
Size Inches*3 Dia. *4 Dia. 4 Dia.
Thickness At BossInches
7/161/21/2
CatalogNo.
GWR3GWR4GWR4A
Max.Bolt Dia.Inches
3/47/81
R O U N D F L A T
GWR
BB
GCW31
* NEMA Standard