Plant Wide Alarm

System

Plant Wide Alarm

System

Alarm TonesAlarm Tones

4 Alarm TonesGeneral Evacuation – WailSevere Weather – Pulsed SteadyLocal Alarm – Pulsed WailAll Clear - Steady

4 Alarm TonesGeneral Evacuation – WailSevere Weather – Pulsed SteadyLocal Alarm – Pulsed WailAll Clear - Steady

Alarm LocationsAlarm Locations

Alarms are located in following locations: Area 2 (Tag # S-M-301E) Area 5 (Tag # S-M-301D) Area 4 (Tag # S-M-301G) Area 6 South (Tag # S-M-301C) Dock (Tag # S-M-301H) North Tank Farm (Tag # S-M-301F)

Alarms are located in following locations: Area 2 (Tag # S-M-301E) Area 5 (Tag # S-M-301D) Area 4 (Tag # S-M-301G) Area 6 South (Tag # S-M-301C) Dock (Tag # S-M-301H) North Tank Farm (Tag # S-M-301F)

Area 2

Area 2

Area 5 Area 5

Area 4Area 4

Area 6 SouthArea 6 South

DockDock

North Tank Farm

North Tank Farm

Discrete AlarmsDiscrete Alarms

Each alarm location is activated thru a radio frequency 456.400 MHz UHF

Alarm Locations are battery powered by 4 - 12 Volt Batteries

Batteries are kept charged by solar panels at each location.

Each alarm location is activated thru a radio frequency 456.400 MHz UHF

Alarm Locations are battery powered by 4 - 12 Volt Batteries

Batteries are kept charged by solar panels at each location.

Alarm ActivationAlarm Activation

Alarm can be activated in 2 locations Northeast Corner of Central Control

Room (Tag # S-M-301A) SS2000D Encoder, Microphone and

Computer

Security Office Administration Building on St. Bernard Hwy.

(Tag# S-M-301B)SS200D Encoder and Microphone only

Alarm can be activated in 2 locations Northeast Corner of Central Control

Room (Tag # S-M-301A) SS2000D Encoder, Microphone and

Computer

Security Office Administration Building on St. Bernard Hwy.

(Tag# S-M-301B)SS200D Encoder and Microphone only

Alarm ActivationAlarm Activation When event has been identified

Appropriate alarm is activated by pressing the pre programmed key sequence on the SS2000D FSK Encoder or the computer in Central Control

Warning tones will sound for the pre-programmed period of 3 minutes or until cancelled.

The Microphone can be used for making emergency voice broadcasts

When event has been identifiedAppropriate alarm is activated by

pressing the pre programmed key sequence on the SS2000D FSK Encoder or the computer in Central Control

Warning tones will sound for the pre-programmed period of 3 minutes or until cancelled.

The Microphone can be used for making emergency voice broadcasts

Activating via the SS2000DActivating via the SS2000DActivating via the SS2000DActivating via the SS2000D

System ActivationSystem ActivationSystem ActivationSystem Activation

2. Press the Function Button

SYSTEM ACTIVATED

1. With Key in, turn Key switch to “ON”

3. Verify function selection

4. Press the “Send” Button

Canceling a Command or an Activation Canceling a Command or an Activation Canceling a Command or an Activation Canceling a Command or an Activation

Before a Function has been sent, Press “CLEAR” to Cancel

After a Function has been sent, Press “CLEAR” if polling is in progress then press “CANCEL ALL” and press “SEND”

CANCEL

ALL

SS2000D SS2000D Alarms and Status IndicatorsAlarms and Status Indicators

SS2000D SS2000D Alarms and Status IndicatorsAlarms and Status Indicators

PRINTER – Indicates when the SS2000 PRINTER – Indicates when the SS2000 sends information to the printersends information to the printer

CARRIER – RF Channel busy indicatorCARRIER – RF Channel busy indicator

AUX. – Auxillary use onlyAUX. – Auxillary use only

KEY – Lights whenever a key on the KEY – Lights whenever a key on the mylar keypad is depressedmylar keypad is depressed

PRINTER – Indicates when the SS2000 PRINTER – Indicates when the SS2000 sends information to the printersends information to the printer

CARRIER – RF Channel busy indicatorCARRIER – RF Channel busy indicator

AUX. – Auxillary use onlyAUX. – Auxillary use only

KEY – Lights whenever a key on the KEY – Lights whenever a key on the mylar keypad is depressedmylar keypad is depressed

PRINTER

CARRIER

AUX.

KEY

Monitor and Activate via the ComputerMonitor and Activate via the ComputerMonitor and Activate via the ComputerMonitor and Activate via the Computer

Recommended View – Map Screen Recommended View – Map Screen Recommended View – Map Screen Recommended View – Map Screen

1. Click “Map”

2. Click “Legend”

Checking for Site StatusChecking for Site StatusChecking for Site StatusChecking for Site Status

Click desired Site

Click PollTo get an updatedSite status

Click “Notepad” to create Notes

System ActivationSystem ActivationSystem ActivationSystem Activation

1. Click “Activate”

3. Click “OK”

2. Click desired Hot Key

SYSTEM ACTIVATED

Canceling a Command or an ActivationCanceling a Command or an ActivationCanceling a Command or an ActivationCanceling a Command or an Activation

Click “Cancel” beforeEntry has been sent.

Click “Cancel All”, “OK,” after Command has been sent.

“Minimize”

Acknowledging an AlarmAcknowledging an AlarmAcknowledging an AlarmAcknowledging an Alarm

Click Acknowledge

Click “System Log”

System MonitoringSystem Monitoring

The PC at the base station in central control continuously monitors the system

The software keeps running log of all events and “Quiet Test” responses

Quiet Tests are performed automatically

Failure of Quiet Test will be indicated on the PC

The PC at the base station in central control continuously monitors the system

The software keeps running log of all events and “Quiet Test” responses

Quiet Tests are performed automatically

Failure of Quiet Test will be indicated on the PC