Plant Wide Alarm System Alarm Tones 4 Alarm Tones General Evacuation – Wail Severe Weather –...
-
Upload
dominic-maxwell -
Category
Documents
-
view
213 -
download
0
Transcript of Plant Wide Alarm System Alarm Tones 4 Alarm Tones General Evacuation – Wail Severe Weather –...
Plant Wide Alarm
System
Plant Wide Alarm
System
Alarm TonesAlarm Tones
4 Alarm TonesGeneral Evacuation – WailSevere Weather – Pulsed SteadyLocal Alarm – Pulsed WailAll Clear - Steady
4 Alarm TonesGeneral Evacuation – WailSevere Weather – Pulsed SteadyLocal Alarm – Pulsed WailAll Clear - Steady
Alarm LocationsAlarm Locations
Alarms are located in following locations: Area 2 (Tag # S-M-301E) Area 5 (Tag # S-M-301D) Area 4 (Tag # S-M-301G) Area 6 South (Tag # S-M-301C) Dock (Tag # S-M-301H) North Tank Farm (Tag # S-M-301F)
Alarms are located in following locations: Area 2 (Tag # S-M-301E) Area 5 (Tag # S-M-301D) Area 4 (Tag # S-M-301G) Area 6 South (Tag # S-M-301C) Dock (Tag # S-M-301H) North Tank Farm (Tag # S-M-301F)
Area 2
Area 2
Area 5 Area 5
Area 4Area 4
Area 6 SouthArea 6 South
DockDock
North Tank Farm
North Tank Farm
Discrete AlarmsDiscrete Alarms
Each alarm location is activated thru a radio frequency 456.400 MHz UHF
Alarm Locations are battery powered by 4 - 12 Volt Batteries
Batteries are kept charged by solar panels at each location.
Each alarm location is activated thru a radio frequency 456.400 MHz UHF
Alarm Locations are battery powered by 4 - 12 Volt Batteries
Batteries are kept charged by solar panels at each location.
Alarm ActivationAlarm Activation
Alarm can be activated in 2 locations Northeast Corner of Central Control
Room (Tag # S-M-301A) SS2000D Encoder, Microphone and
Computer
Security Office Administration Building on St. Bernard Hwy.
(Tag# S-M-301B)SS200D Encoder and Microphone only
Alarm can be activated in 2 locations Northeast Corner of Central Control
Room (Tag # S-M-301A) SS2000D Encoder, Microphone and
Computer
Security Office Administration Building on St. Bernard Hwy.
(Tag# S-M-301B)SS200D Encoder and Microphone only
Alarm ActivationAlarm Activation When event has been identified
Appropriate alarm is activated by pressing the pre programmed key sequence on the SS2000D FSK Encoder or the computer in Central Control
Warning tones will sound for the pre-programmed period of 3 minutes or until cancelled.
The Microphone can be used for making emergency voice broadcasts
When event has been identifiedAppropriate alarm is activated by
pressing the pre programmed key sequence on the SS2000D FSK Encoder or the computer in Central Control
Warning tones will sound for the pre-programmed period of 3 minutes or until cancelled.
The Microphone can be used for making emergency voice broadcasts
Activating via the SS2000DActivating via the SS2000DActivating via the SS2000DActivating via the SS2000D
System ActivationSystem ActivationSystem ActivationSystem Activation
2. Press the Function Button
SYSTEM ACTIVATED
1. With Key in, turn Key switch to “ON”
3. Verify function selection
4. Press the “Send” Button
Canceling a Command or an Activation Canceling a Command or an Activation Canceling a Command or an Activation Canceling a Command or an Activation
Before a Function has been sent, Press “CLEAR” to Cancel
After a Function has been sent, Press “CLEAR” if polling is in progress then press “CANCEL ALL” and press “SEND”
CANCEL
ALL
SS2000D SS2000D Alarms and Status IndicatorsAlarms and Status Indicators
SS2000D SS2000D Alarms and Status IndicatorsAlarms and Status Indicators
PRINTER – Indicates when the SS2000 PRINTER – Indicates when the SS2000 sends information to the printersends information to the printer
CARRIER – RF Channel busy indicatorCARRIER – RF Channel busy indicator
AUX. – Auxillary use onlyAUX. – Auxillary use only
KEY – Lights whenever a key on the KEY – Lights whenever a key on the mylar keypad is depressedmylar keypad is depressed
PRINTER – Indicates when the SS2000 PRINTER – Indicates when the SS2000 sends information to the printersends information to the printer
CARRIER – RF Channel busy indicatorCARRIER – RF Channel busy indicator
AUX. – Auxillary use onlyAUX. – Auxillary use only
KEY – Lights whenever a key on the KEY – Lights whenever a key on the mylar keypad is depressedmylar keypad is depressed
PRINTER
CARRIER
AUX.
KEY
Monitor and Activate via the ComputerMonitor and Activate via the ComputerMonitor and Activate via the ComputerMonitor and Activate via the Computer
Recommended View – Map Screen Recommended View – Map Screen Recommended View – Map Screen Recommended View – Map Screen
1. Click “Map”
2. Click “Legend”
Checking for Site StatusChecking for Site StatusChecking for Site StatusChecking for Site Status
Click desired Site
Click PollTo get an updatedSite status
Click “Notepad” to create Notes
System ActivationSystem ActivationSystem ActivationSystem Activation
1. Click “Activate”
3. Click “OK”
2. Click desired Hot Key
SYSTEM ACTIVATED
Canceling a Command or an ActivationCanceling a Command or an ActivationCanceling a Command or an ActivationCanceling a Command or an Activation
Click “Cancel” beforeEntry has been sent.
Click “Cancel All”, “OK,” after Command has been sent.
“Minimize”
Acknowledging an AlarmAcknowledging an AlarmAcknowledging an AlarmAcknowledging an Alarm
Click Acknowledge
Click “System Log”
System MonitoringSystem Monitoring
The PC at the base station in central control continuously monitors the system
The software keeps running log of all events and “Quiet Test” responses
Quiet Tests are performed automatically
Failure of Quiet Test will be indicated on the PC
The PC at the base station in central control continuously monitors the system
The software keeps running log of all events and “Quiet Test” responses
Quiet Tests are performed automatically
Failure of Quiet Test will be indicated on the PC