Post on 09-Oct-2019
HBUD Series LED High BayImportant: Read all instructions prior to installation.
User ManualPart Number:
Dimensional Drawings
Rev Date: V1.0 10/27/2017Rev Date: V1.0 10/27/2017
5yr
HBUD-50K100W, HBUD-50K150WHBUD-50K200W, HBUD-50K300W
HBUD Series LED High BayUser Manual
Part Number:HBUD-50K100W, HBUD-50K150W, HBUD-50K200W, HBUD-50K300W
HBUD-50K100W HBUD-50K150W
HBUD-50K200W HBUD-50K300W
5.12in130.16mm
6.05in153.67mm
10.95in278.13mm
8.69in220.73mm
7.19in182.63mm
6.00in152.40mm
6.03in153.26mm
10.95in278.13mm
8.69in220.73mm7.19in
182.63mm
6.00in152.40mm
6.03in153.26mm
10.95in278.13mm
8.69in220.73mm7.19in
182.63mm
7.52in191.13mm
6.03in153.26mm
8.69in220.73mm
10.95in278.13mm
7.19in182.63mm
7.52in191.13mm
6.03in153.26mm
8.69in220.73mm
10.95in278.13mm
7.19in182.63mm
6.35in161.29mm
12.63in320.91mm
12.64in321.01mm
9.61in244.09mm
7.95in201.98mm
User ManualPart Number:
HBUD series LED High BayImportant: Read all instructions prior to installation.
Included Parts
Specifications
Optional Accessories
1 - High Bay Light 1 - Eye Bolt 1 - Washer
Microwave Motion Sensor (HBUD-MS)PC Reflector (HBUD-8-PR)U-Bracket (HBUD-8-UB)
Rev Date: V1.0 10/27/2017
Product HBUD-50K100W HBUD-50K150W HBUD-50K200W HBUD-50K300WIntensity 13000 lm 19500 lm 26000 39000Operating Voltage Range 100~277 VAC 100~277 VAC 100~277 VAC 100~277 VACWattage 102W 152W 206W 313WBeam Angle 120 degree 120 degree 120 degree 120 degreeColor Temperature 5000 K 5000 K 5000 K 5000 KCRI >80 >80 >80 >80Operating Temperature -22~122°F (-30~50 °C) -22~122°F (-30~50 °C) -22~122°F (-30~50 °C) -22~122°F (-30~50 °C)IP Rating Weatherproof IP65 Weatherproof IP65 Weatherproof IP65 Weatherproof IP65LED Lifetime 54,000 Hours 54,000 Hours 54,000 Hours 54,000 HoursDimmable 1~10V 1~10V 1~10V 1~10VPower Factor >0.93 >0.93 >0.93 >0.93Fixture Weight 7.5 lbs (3.40Kg) 8.3 lbs (3.76Kg) 9.5 lbs (4.30Kg) 15 lbs (6.8Kg)Standards and Certifications CE, RoHS, UL, FCC, DLC CE, RoHS, UL, FCC, DLC CE, RoHS, UL, FCC, DLC CE, RoHS, UL, FCC, DLCWarranty 5 Years 5 Years 5 Years 5 Years
Eye Bolt Installation Instructions
U-Bracket Installation Instructions
PC Reflector Installation Instructions
Motion Sensor Installation Instructions
HBUD-50K100W, HBUD-50K150WHBUD-50K200W, HBUD-50K300W
1. Insert Eye Bolt and Washer into threaded hole on back of fixture and tighten. Hang fixture by attaching Eye Bolt (Fig. 1) to an existing hook or carabiner.
2. Connect the fixture wires to the corresponding wires in the junction box (not included).
Black
White
Green
BlackL L
N N
GND GND
White
Green
Warning
Wiring Diagram
• This product should be installed by a fully certified electrician in accordance with local building and electrical codes.
• Due to risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.
• Failure to properly support the fixture during installation may cause damage or injury, for which the manufacturer is not responsible. Ensure the light bracket/eye bolt is securely mounted and will support the weight of the fixture.
1. Secure mounting plates to fixture with provided 4 x 21mm allen screws using 4mm allen wrench (A). Attach U-Bracket to mounting plate with 2 x 27mm allen screws and nuts using 6mm allen wrench (B).
2. Position desired angle of U-Bracket and secure with 2 x 4mm allen screws (C).
3. Mount Fixture to surface.4. Connect wiring to power supply. Black to Line, White to
Neutral, and Green to Ground.5. Restore power to circuit to test function.
1. Remove power prior to installation.2. Motion sensor and compact J-Box come attached to mounting
plates. Position motion sensor and provided compact J-Box on opposite sides of the light.
3. Attach motion sensor to light using 2 x 21mm Allen Screws using 4mm allen wrench (A).
1. Turn fixture upside down.2. Line up 3 holes from PC Reflector
to 3 threaded holes on light. 3. Screw 3 phillips screws to secure
PC Reflector
MotionSensor
Compact J-Box
From LED
1-10VDimming
Wires From LED
Power Source
Threaded Holes for PC Reflector
Threaded Holes for PC Reflector
(B)
(C)(B)
(C)
(A)(A)
4. Attach compact J-Box to light using 2 x 21mm Allen Screws using 4mm allen wrench (B).
5. Make wiring connections according to diagram.
6. Connect to power source. Black to Line, White to Neutral, and Green to Ground.
7. Restore power to circuit to test motion sensing functionality. *Note: Refer to motion sensor manual for operation.