Post on 03-Dec-2021
Doc. No. F702M-LC2E
Optical Device Medical Device System Engineering XENOSYS CO., LTD.
2, Venture-ro, 100 Beon-gil, Yeonsu-gu, Incheon 22013, Korea TEL. 82-32-875-9811~2 FAX. 82-32-875-9813 www.xenosys.co.kr / sales@xenosys.co.kr
LooksCAM2
CAMERA SYSTEM USER MANUAL
CAMERA SYSTEM (LooksCAM2) 2 www.xenosys.co.kr
Table of Contents
INTRODUCTION ....................................................................................................... 4
SAFETY & PRECAUTIONS ...................................................................................... 5
FEATURES ................................................................................................................ 8
COMPONENTS .......................................................................................................... 9
EACH COMPONENT & FUCNTIONS .................................................................... 10
1. Main Body (Camera Control Unit, LC2-CU) .................................................................. 10
2. Battery Pack (BTP-LC2) ................................................................................................ 11
3. Head Assembly Unit (LC2-HA) ...................................................................................... 12
4. Remote Controller (LC2-RC) .......................................................................................... 13
5. DC Power Supply (FW8000MUSB05) ............................................................................ 14
HOW TO USE .......................................................................................................... 14
INSTALLATION ...................................................................................................... 16
1. Insert & Removal of Micro SD Card (FORMAT) ........................................................... 16
2. Assemble Main Body & Battery Pack ............................................................................ 17
3. Assemble Main Body & Head Assembly Unit ................................................................ 18
4. Connect Video-Out Port ................................................................................................. 19
5. How to update the firmware ........................................................................................... 19
OPERATING INSTRUCTIONS ................................................................................ 20
1. Power On/Off ................................................................................................................... 20
2. Video Recording .............................................................................................................. 21
3. Snapshot ........................................................................................................................... 21
4. Turn on LED .................................................................................................................... 22
5. Insert the Highlight Tag .................................................................................................. 23
CAMERA SYSTEM (LooksCAM2) 3 www.xenosys.co.kr
6. Auto Focus ....................................................................................................................... 23
7. Zoom-in & Zoom-out ...................................................................................................... 23
8. Check Video by Video-out port ..................................................................................... 23
9. Battery Status LED.......................................................................................................... 24
THE VIEWER .......................................................................................................... 26
1. WiFi Connection .............................................................................................................. 26
2. How to install the Viewer ............................................................................................... 27
3. Features & Fuctions of Viewer ...................................................................................... 27
4. Detail Options / Configurations ...................................................................................... 29
(1) Language Setting: Choose which language will be used for control unit notices.. . 29
(2) WiFi : There are two modes Ap and Station. ............................................................................. 29
(3) Resolution: Set up for resolution 1080p or 720p ..................................................................... 30
(4) Image Control: Set up for image color by manual or automatic (Recommend for
automatic) ................................................................................................................................................................. 30
(5) Lens ................................................................................................................................................................ 30
(6) AF Mode....................................................................................................................................................... 30
(7) LED LIGHT: Set up the brightness of LC2-CU during the booting process. ................ 30
(8) MIC, Speaker: Adjust main body microphone and speaker volume. .............................. 30
5. Button Details on Menu ................................................................................................... 30
BASIC TROUBLESHOOTING ................................................................................. 31
SPECIFICATIONS ................................................................................................... 33
(1) Control Unit (LC2-CU) ............................................................................................................................ 33
(2) Battery Pack (BTP-LC2) .......................................................................................................................... 33
(3) Head Assembly Unit (LC2-HA) ........................................................................................................... 33
(4) Remote Controller (LC2-RC) ............................................................................................................... 33
(5) DC POWER SUPPLY (DC Power Supply, FW8000MUSB05) ......................................... 34
(6) USB Power Cable (LC2-USBC) ............................................................................................................ 34
(7) Video-Out Cable (LC2-VOC) ............................................................................................................... 34
2. Detailed Specifications .................................................................................................... 35
3. Label for packaging & components ...................................................................................... 36
ELECTROMAGNETIC COMPATABILITY .............................................................. 37
CAMERA SYSTEM (LooksCAM2) 4 www.xenosys.co.kr
TRANSPORTATION ............................................................................................... 38
STORAGE ................................................................................................................ 38
CLEANING INSTRUCTIONS .................................................................................. 39
SERVICES & WARRANTY ...................................................................................... 39
INTRODUCTION
This product is the external medical camera to record
patient’s affected area or surgery during the medical
treatment by hospital. The basic components consist
of the camera optical module, camera head, camera
control unit (main body), and LED lens module.
There are two options to check the input video
through camera head spontaneously. One is to
connect VIDEO OUT port of the camera control unit
to HDMI port of the monitor. Another is to use wifi
setting by monitor or computer screen.
Recorded video file is stored in Micro SD card.
Here are summarized features of this product.
1. There is no limit in movement as it is wearable camera.
2. Possible to record shadow less video as the light & the line of sight from the operator is same.
3. Big depth of focus will provide the good focus while operation.
4. The advantage of the view point from the operator when trainees see recorded videos.
5. Use only light source if you do not use recording.
The description below is KFDA approval condition as the medical device.
Registration No. 1909 Certificate
No. Gyeongin Jesin 07-117
Product Category
I General Instruments Class Class 1
Product Category
II A31000 Medical Mirror
Product
Category III
A31020.01 External Medical
Camera
CAMERA SYSTEM (LooksCAM2) 5 www.xenosys.co.kr
Product Model
No. LooksCAM2
Manufacturer Xenosys Co., Ltd.
Country of Origin Republic of Korea
SAFETY & PRECAUTIONS
Before the usage, you should read the manual & precautions carefully and use it properly. You
should follow next procedures and warnings about the battery & other components to prevent any
fire, injury, or damage to human body.
WARNING for Safety:
WARNING for Power Unit:
WARNING for Main Body:
Do not heat the product with microwave machine or oven.
Do not dispose the battery into a fire.
Do not make direct connection between ‘+’ and ‘-‘ of the battery terminal (both edge of
battery) simultaneously by the conductor (any metallic object, coin, or clip) which will cause
the short-circuit to occur fire or injury to human body. Thus the charged battery should be
handled with care.
The product is not waterproof (Ordinary equipment, IPX0), so avoid the humidity and water.
Do not use in the presence of a flammable anaesthetic mixture with air, oxygen, or nitrous
oxide.
Do not use any undesignated charger by Xenosys. If any damage or unexpected hazard
happens by the usage of undesignated charger, the manufacturer is free from the
responsibility.
In case of any oil spillage or liquid to inside of the product may cause fire or electric shock.
Then turn off the power immediately and disconnect the power cord.
Do not bend or twist the power cord excessively. It may cause fire or electric shock.
Do not touch the power cord with wet hand which may cause electric shock or equipment
damage.
Do not use LooksCAM2 with connecting directly to the battery pack during the operation or
medical practice.
CAMERA SYSTEM (LooksCAM2) 6 www.xenosys.co.kr
Storage Environment (Operating)
Ambient Temperature 6℃ - 40℃(43℉ - 104℉)
Relative Humidity 30 - 85% at 6℃ - 40℃(43℉ - 104℉)
Pressure 860 hPa - 1060 hPa
Transportation & Storage Environment (Non-operating)
Ambient Temperature 10℃ - 40℃
WARNING for LED Lens Module:
Never disassemble or undertake modification of the equipment.
Do not put any metal or flammable object into the main body. It may cause fire or electric
shock.
Any drop or hard shock may cause the potential damage to the equipment.
Do not use or store the equipment in the area where get the direct ray of light, humidity, dust
or soot. Clean up with a dry and soft cloth.
Do not use the detergent or chemical fluid to clean which may cause discoloration.
Avoid the reach of children or pets.
Maintain the following conditions for storing the product.
Do not drop, crush, or put a high pressure on LED lens module.
Clean LED lens surface with dipped alcohol or methanol in dry cloth softly.
Do not bend or twist the connection cable between the main body and LED lens module which
may cause the defective.
LED optic outside emits heat, so be careful on touching.
Do not look directly into LED lens module or some one’s eyes to avoid the risk of permanent
eye damage.
Refer to the below label for the caution.
CAMERA SYSTEM (LooksCAM2) 7 www.xenosys.co.kr
WARNING for Battery:
Never disassemble the battery pack case in force which may cause the malfunction or explosion.
WARNING for DC Power Supply:
WARNING for Disposal
At the first installation, make sure to check the external figure of battery. If there is any spill,
swollen, stink, or unusual found, then do not use the product and contact the dealer. If it’s
normal, then charge the battery fully and use it.
The battery is lithium-polymer rechargeable one.
When transporting only battery, make sure to keep it in soft case. Do not make any conductor
to connect the battery charging point.
The battery operating time may shorten using in the cold place (below 0℃) even fully charged
one. In that case, warm up the battery within the pocket before using LooksCAM2. Do not heat
up the battery with microwave or any heater. Recommended ambient temperature to operate is
6℃ - 40℃.
Use only the charger which is provided by Xenosys.
Charger battery in the range of +10℃ - +35℃. It may take longer to charger the battery out of
this temperature range.
Provided battery can be charged and discharged about 300 times at room temperature.
Lithium-ion battery is expendables, thus if the operating time is shortened after full charge, we
recommend exchanging new battery.
Be careful on benzene, thinner, alcohol (volatile & flammable fluid) and water. If those
chemicals penetrate the battery, it may cause the trouble in circuit and any accident.
If there is any swollen battery, spill, emit, or fire, stop using immediately and contact the
distributor (dealer) or the manufacturer.
Never use any damaged battery and charger.
In case of the first installation or unused long time, then charge the battery fully before using.
Do not connect any metallic objects between the cradle connector and battery. This may
cause the defective on the charger and DC Power Supply.
Use only the charger which is provided by Xenosys on the phone jack. This may cause the
defective on the charger and DC Power Supply.
The desired lifespan of LooksCAM II is 1 year. In case of careless disposal, it may pollute the
environment, so make sure to separate collection.
CAMERA SYSTEM (LooksCAM2) 8 www.xenosys.co.kr
FEATURES
1. Operating Principle
Enable to record Full HD video through high quality wide-angle lens with 4.0 Mega pixel CMOS
image sensor. Easy to install and operate by every people to share the recorded video through
wireless wifi to play and download via mobile phone.
2. Electrical Rating
1) Battery Pack: 3.6 V , 10050 mAh (Lithium ion, : This symbol means Direct Current)
2) DC Power Supply: Input 100-240 V~ (50-60 Hz, 0.3 A), Output 5 V , 2200 mA
3. Protection Classification & Type against Electric Short
1) Protection Classification:
① Battery Pack: Internal Power Device
② DC Power Supply: Class II Device
2) Protection Type: N/A
4. Safety Circuit: Contains protection circuit for over-current & over-voltage
5. Operation Block Diagram: Refer to below photo
CAMERA SYSTEM (LooksCAM2) 9 www.xenosys.co.kr
COMPONENTS
1. Main body (Camera control unit) 2. Battery pack (2 pcs) 3. Head Assembly unit
4. Remote controller 5. RigidHeadband 6. DC Power supply
7. Micro SD card socket 8. USB power cable 9. Cable clamp
10. Video Out cable (3.6M) 11. AAA battery 12. Micro SD card (128GB)
13. Gown clip 14. RHB02-PADSET 15. Mini driver 16. Cleaning cloth
BTP-LC2 LC2-CU LC2-HA
RHB02-LC
LC2-RC
FW8000MUSB05
LC2-USBC LC2-SDCS
LC-AAABT
MLC type UHS-I
LC2-VOC LC2-SDC
GOC RHB02-PADSET DRV07 CC-01
CAMERA SYSTEM (LooksCAM2) 10 www.xenosys.co.kr
WARNING:
Components may change for safety and better performance without prior notice.
EACH COMPONENT & FUCNTIONS
1. Main Body (Camera Control Unit, LC2-CU)
Each Part Function
①Initialization Key If you press 1 second, the device will reboot. If you hold this key for 5 seconds, all settings will be initialized for factory set up and SC card will be formatted.
②Camera Sensor Port Connection port with head assembly unit cable
③Battery Status LED LED status color and battery operating time (3 step will be used for recording & light) 1. Fully charged Green LED on (3 hours 30 minutes) 2. Orange LED on (2 hours 30 minutes) 3. Blinking Orange LED (1 hour) 4. When Orange LED blinking fast 2 minutes then turn off.
④Power Switch Power ON/OFF: Hold the button to downward (1 second) When you move the power switch to upward, all buttons of main body will not work.
⑤Record Button Video Recording Start / Stop Button REC LED ON: System initialization completed REC LED Blinking: Video Recording is in process REC LED OFF: Ongoing of system initialization or malfunction
⑥Snapshot Button Quick press for one snapshot, Hold for continuous shots Snapshot Button LED ON: WiFi On, Possible to connect viewer Snapshot Button LED OFF: WiFi Off, Not possible to connect viewer
⑧ Pairing Switch ⑪ Micro SD Card Slot
⑩ Speaker
⑨ Video-Out
④ Power Switch
⑤ Record Button
⑥ Snapshot Button
⑦ LED Light Button
⑬ Battery power
Input pin
③ Battery Status LED
① Initialization Key
② Camera Sensor Port
⑫ USB Slot
CAMERA SYSTEM (LooksCAM2) 11 www.xenosys.co.kr
⑦LED Light Button LED Light ON/OFF Button
⑧Pairing Switch Use for remote controller pairing set up (refer to Page 14)
⑨Video-Out Output port for recoded video to external device.
⑩Speaker Voice messages
⑪Micro SD Card Slot Store recorded video files. Possible recording time is less than 2 hours: 1 warning beep signal Possible recording time is less than 30 minutes: 1 warning beep signal Possible recording time is less than 10 minutes: Warning beep signal for every 2 minutes
⑫USB Slot Connect DC Power Supply to charge the battery pack.
⑬Battery power input pin Connect to battery pack charging points
⑭USB Slot LED If it’s connected to DC power supply – Green light On. If it’s battery charging status – Orange light On.
WARNING:
Battery input Pin on main body USB slot is quite vulnerable on external shock, so please be careful
on assembling or disassembling with battery pack. If this charging pin has been damaged, the
main body will NOT work properly and not possible to use.
2. Battery Pack (BTP-LC2)
Each Part Function
① Battery Release Knob Push to arrow pointed direction to assemble or disassemble the main body and battery
pack.
② Battery Hook To connect main body (LC2-CU) and battery pack
③ USB Slot Connect DC Power Supply to charge the battery pack.
④ Battery Status LED Shows the charging status of battery pack
Fully Charged – Green, In process of Charging – Orange
⑤ Battery power output pin Connected to charging pin of main body.
⑤ Battery Status LED
① Battery Release Knob
③ USB Slot
② Battery Hook
④ Battery power output pin
CAMERA SYSTEM (LooksCAM2) 12 www.xenosys.co.kr
④ Clamp
⑤ Camera lens
(f14mm standard)
⑥ LED Lens Module
②Adjustable link `
①Microphone
③Recording status LED
WARNING:
1. ③USB slot of battery pack should be only used for charging usage, and it cannot be
used during the usage of camera.
2. There is protector PCB for this battery pack so when charging via USB slot after 7 hours
charging, it will stop charging.
3. Head Assembly Unit (LC2-HA)
Each Part Function
① Microphone Microphone Input
② Adjustable Link To move up or down of camera head assembly unit
③ Recording Status LED
LED ON: Stand By status
LED Blinking: Recording is in process
LED OFF: System initialization or Camera sensor connection error.
④ Clamp To fix at rigid headband (RHB02)
⑤ Camera Lens
Choose your desired lens between f=14mm, f=20mm depending on FOV.
Field of View (Crosswise)
f=14mm : 137mm @ WD400mm (Basic set up)
f=20mm : 94mm @ WD 400mm
⑥ LED Lens Module . There are 3 kinds of LED lens and you may choose one.
Class Model Feature (Field of View Size) Remark
Standard LLM82 Ø 82mm@WD400mm Standard
Option 1 LLM74 Ø 74mm@WD400mm
Option 2 LLM66 Ø 66mm@WD400mm
A180138
⑦ Serial Number
CAMERA SYSTEM (LooksCAM2) 13 www.xenosys.co.kr
⑦ Product ID Code
Will provide last 3 digit number from camera serial number
Configuration will be input viewer set up option “LENS”
Ex) A180138 -> input 138 to activate the viewer
4. Remote Controller (LC2-RC)
Each Part Function
Record Button Start or Stop video recording
Snapshot Button Quick press for one snapshot, Hold for continuous shots
Continuous shots: 5 snapshots for 1 second and not feasible when video recording is on
Hightlight Tag Buggon Press this button if you want to Tag specific moment or time lapse while recording or playing
the video.
Auto Focus Button Focus on special subject automatically.
Zoon In Button Digital zoom in and zoom out function
4 steps of magnifications: 1.0x, 1.5x, 2.0x, 3.0x Zoom Out Button
LED Light Button
LED On/Off Button
LED brightness level can be controlled 4 steps 1, 2, 3, OFF in the "config.exe" file.
(See 21 page)
AAA Battery Slot 1.5V (2 EA), AAA size.
Reboot switch for control unit Press this switch more than 5 seconds then LC-CU2 will reboot.
WARNING: The main body and remote controller are provided with pairing set up. The below table
is how to set up & release pairing. You should disconnect head assembly unit cable before setting up
the pairing.
Reboot switch for
CU
AAA
battery
slot
CAMERA SYSTEM (LooksCAM2) 14 www.xenosys.co.kr
Paring Set Up
1. Connect USB cable to main body (LC2-CU).
2. Main body (LC2-CU) power on
3. Press the paring switch quickly, then LED on the backside of
main body will blink “Blue”
4. Press any button on remote controller -> Blue LED will blink
repeatedly
5. Pairing completed
A. You can use one remote
controller for several units by
pairing.
B. If the main body is released in
paring, it can be controlled by
several remote controllers.
Pairing Release
1. Connect USB cable to main body (LC2-CU).
2. Main body (LC2-CU) power on
3. Press and hold the pairing switch for 5 seconds -> Blinking
LED (Blue) on the back side of main body
4. Press any button on remote controller -> Blue LED will blink
repeatedly
5. Pairing release completed
5. DC Power Supply (FW8000MUSB05)
A. Input Voltage 100/240 VAC, 50/60 Hz, 0.3A
B. Output Voltage DC5V, 2.2A
C. Indicating LED Green LED light means normal power supply
WARNING: Charging the battery should be used with Xenosys provided DC
power supply. If any other similar power supply used for charging to cause the
malfunction or faulty, it will be charged for additional cost.
HOW TO USE
1. Preparation before use
1) Unpack the box and check components quantity and external figures are good or not.
2) Read the manual to fully understand how to use.
3) Charge the battery pack before use and must use Xenosys provided DC Power Supply
(FW8000MUSB05).
2. How to use and control
1) Check Micro SD is imbedded & assembled.
2) Assemble the main body and fully charged battery pack.
3) Connect head assembly unit to main body and check the connection status.
① LED(Blue)
② Pairing Switch
CAMERA SYSTEM (LooksCAM2) 15 www.xenosys.co.kr
4) Fix the headband by using clamp.
5) Check the camera alignment or video,
connect video out cable to HMDI to
find or connect wifi via tablet.
6) Press and hold ON/OFF button for 1
second to boot, press and hold button to
downward for 3 seconds will make power
OFF. If you wish to NOT to make any
button to be operated, move the button to
upward to make HOLD mode, then only operated by remote controller. To move the button
downward make HOLF mode OFF.
7) After booting complete, REC button will turn on, then you can start recording by pressing REC
button.
8) LED button on main body/remote controller will do ON/OFF. You can change light intensity at
viewer configuration “LED LIGHT”.
9) If you wish to finish recording, press REC button will make LED button blinking then finish
recording.
10) You can turn off by pressing & holding the button to downward for 3 seconds.
11) Refer to main manual for detailed operating methods.
3. Storage and maintenance
1) Make clean the product after usage to be ready for next use.
* Clean with cleaning cloth included in the box for external cleaning. Use slightly dipped
neutral detergent if it’s dirtier. DO NOT make any humidity or water into the main body.
2) Store in a place where there is no possibility of affecting this product by containing air
pressure, temperature, humidity, ventilation, daylight, dust salt, and ion.
3) Store in safe place from slope, vibration, and impact.
4) Avoid storage area where chemicals or generating gas.
5) If any problem of faulty, stop using it and ask nearest distributor or agent for repairs.
6) DO NOT disassembly, repair, or remodel.
CAMERA SYSTEM (LooksCAM2) 16 www.xenosys.co.kr
INSTALLATION
1. Insert & Removal of Micro SD Card (FORMAT)
1) Prepare Micro SD card with formatted by FAT32 (File allocation size=32KB)
2) ① Insert Micro SD to main body.
WARNING: Make sure the direction of ①Micro SD card is correct when inserting to ②Card
Slot. If not, it may cause the breakage of ①Micro SD card.
WARNING: Warranty period of Micro SD card is 6 months from the date of purchase. Please
exchange Micro SD card immediately if you find problem in recorded video as it is expendables.
Periodical checkup for the recorded file is needed.
3) Press Micro SD card slightly to remove from the main body.
4) Format: When Micro SD card is inserted, then press this format key more than 5 seconds, all
files will be DELETED and formatted with FAT32.
WARNING: Check below contents before using Micro SD card.
Micro SD card is expendables with certain period of lifespan, so it needs periodical check up and
exchange.
Recommended using Xenosys provided Micro SD card. If there is any defective happen while
using non-Xenosys provided one, we don’t have the responsibility for that defective.
Make sure to remove Micro SD card after turn off the main body. The opposite way may cause
the defective and malfunction.
Prevent the loss of recorded files (i.e. important data) by downloading recorded files from Micro
SD card to move personal computer.
Normal recording process is possible after formatting with FAT32 (File Allocation Size=32KB).
If the file allocation size is NOT 32KB, SD card may not perform in best condition. You
may see “format warning message” in TV screen if you are connected to Video-Out cable.
Firstly, you should back up important files, and then you may format.
If OS is Window XP, the file allocation size may not fit to 32KB. You can format SD card at
different computer with OS – i.e. Window 7.
① Micro SD card
② Micro SD card slot
③ FORMAT
CAMERA SYSTEM (LooksCAM2) 17 www.xenosys.co.kr
Other files like NTFS/EXT, etc. will not be supported to play. Voice message of ”Memory card is
not detected” will come out when there is defective in Micro SD card.
2. Assemble Main Body & Battery Pack
1) Match 4 holes of ③Main Body to same 4 hooks of ②Battery Pack and insert.
2) Push ③Main Body to the direction of red arrow and assemble ②Battery Pack.
3) Push ②Battery Release Knob to the direction of RED arrow and push the ①Main Body to
the direction of printed arrow on battery pack to disassemble.
4) ⑤ The charging points of the main body is very weak at the external shock, so be careful
in handling.
5) To charge the battery, remove the battery from the main body ⑤Connect the USB slot and
DC power supply with USB power cable, an then connect wall AC power (100/240 VAC,
50/60 Hz, to plug the power supply.
WARNING:
- Battery power input pin is VERY weak at the external shock, so be careful in assembling the
battery pack. If the charging port is broken, the operation of LooksCAM II may NOT be
possible.
- Store the main body and battery pack with separated to prevent the battery discharging.
④ Battery power input pin
① Battery Release Knob
⑤ USB Slot
③ Battery Hook
② Main Body
CAMERA SYSTEM (LooksCAM2) 18 www.xenosys.co.kr
3. Assemble Main Body & Head Assembly Unit
1) Connect the main body plug of head assembly unit cable to ②Camera sensor port of main body.
2) Fix ③Clamp of head assembly unit to the headband.
3) Verify if the product ID code is correct at Viewer set up option “Lens”.
WARNING:
- If the connection is bad on head assembly unit cable, the system booting process will continue.
- If the connection is bad on head assembly unit cable, UMS mode (connecting to USB) may not
work well.
- If the camera sensor plug of head assembly cable is twisted or damaged by hard pull off, video
out cable can be severely damaged which will cause loose contact to image transfer.
Recommended storage of LooksCAM2 will be stored with all head assembly unit cable connected.
MB
Head Assembly Unit
Headband
③Clamp
⑤Camera lens (2 types)
Head Assembly Unit Cable
Main Body
①Main Body Plug
②Camera Sensor Port
A180138
⑤ Product ID code
CAMERA SYSTEM (LooksCAM2) 19 www.xenosys.co.kr
4. Connect Video-Out Port
1) Prepare ①TV with HDMI port.
2) Connect ③Video-Out cable to ②Video-Out port of main body and ①TV HDMI port.
3) If necessary, use ④Cable clamp to prevent the cable pull off.
5. How to update the firmware
1) Copy firmware file(6.x.x.xx.bin) to IN folder of Micro SD card
2) Insert the SD card in LooksCAM2 Micro SD Card Slot and press power switch to downward (1
second)
3) LED on main body will blinking and firmware update will process. When the update is finished,
the power will turn off automatically.
4) If any error occurs, try the step from 1).
WARNING:
①TV or Monitor
②Main Body Video-Out Port
③Video-Out Cable
④Cable Clamp
CAMERA SYSTEM (LooksCAM2) 20 www.xenosys.co.kr
- Do NOT stop power or turn off while doing the firmware update which may cause fatal damage
to system.
- Make sure to move all recorded files & snapshots before firmware update.
OPERATING INSTRUCTIONS
1. Power On/Off
WARNING:
- Turn on power after connecting head assembly unit cable to main body and check Micro
SD card is inserted.
1) ②Power ON: Press power switch to downward (1 second), then system initialization (booting)
will proceed.
Power on will start with the sound of “DingDongDeng” and the battery status LED will blink green
light while booting. When the system initialization will complete, LED sign on Record Button will
come with the sound of “DingDong”
2) ②Power OFF: Press power switch to downward and hold 2 seconds to turn off.
3) ①Hold ON/OFF: After booting, if you press Hold button to upward, all buttons will NOT work,
but all buttons from remote controller will work. This function is to prevent any unexpected
(unwanted) button press while doing on procedure.
4) If you press record button without Micro SD card, the error message "Memory card s empty" will
come out.
Power Switch
② Power ON/OFF
① Hold ON/OFF
Record Button
Snapshot Button
LED light Button
Head Assembly Unit Cable
CAMERA SYSTEM (LooksCAM2) 21 www.xenosys.co.kr
2. Video Recording
1) Connect the head assembly unit to main body and insert Micro SD card before turn on the power.
Turn on main body and make sure battery is enough to operate.
When LED on ②[REC] button will come, the system initialization completed (Record is ready).
2) Recording will NOT start automatically. You have to press ②[REC] button and the video
recording will start with [REC] button LED on.
3) If you press ②[REC] button again while doing recording, LED will stop blinking and [REC] LED
sign will be on.
4) MIC setting is always ON, voices also be recorded on files.
3. Snapshot
1) Press quickly will make a snapshot.
2) Press and hold the button will make continuous shots (5 shots with 1 second)
3) Continuous shots will not work while recording is in process.
WARNING: SD card memory capacity warning sound
WARNING:
Video recording & snapshot function is possible with Micro SD card inserted status.
If Micro SD card is pull out or eliminated when power is on (during recording), some of
recorded videos can be deleted or SD card can be damaged not possible to use.
If the battery status is LOW, LED will blink then shut down the power automatically.
One file will be generated with 30 minutes recording video.
Recorded files will be stored in <sd card:d> d:/DCIM/YYYYMMDD/.
Extended file format is mp4 and encoding mode is H.264.
Example of recorded file: YYYYMMDD_hhmmssXX.mp4 (Year-Month-Date_Time-Minutes-
Seconds-Sequence number.mp4)
One file with 30 minutes will be about 2.5GB and then another file will be generated.
If SD card or camera sensor plug has been pull out during the video recording, the
1 beep sound: Possible recording time is less than 1 hour
1 beep sound again: Possible recording time is less than 30 minutes
3 beep sound: Possible recording time is less than 10 minutes
① Power Switch
③ Snapshot Button
②Record Button
CAMERA SYSTEM (LooksCAM2) 22 www.xenosys.co.kr
automatic file restoration program will activate. However, it is not always guaranteed to
restore files because of SD card damage and SD card cannot be used.
4. Turn on LED
1) Connect the head assembly unit to main body, and turn on while Micro SD card is inserted. If
the battery power is enough, system initialization will proceed, and then LED on [REC] button
will come up which is completed system initialization.
2) LED Light Button: LED On/Off Button
STEP lx @WD400mm
LLM82 LLM74 LLM66
1st 19,000 21,000 29,000
2nd 30,000 32,000 44,000
3rd 39,000 43,000 59,000
4th OFF OFF OFF
3) LED brightness level can be controlled 4 steps 1, 2, 3, OFF.
After booting is completed, default setting of LED light brightness can be changed by running
config.exe file inside of SD card. The default level is one step.
4) Run config.exe file to change “Light Level” on desired level and press “Save Config” to save
the configuration.
5) New setting can be used after turn off & reboot the main body.
②LED Light Button
CAMERA SYSTEM (LooksCAM2) 23 www.xenosys.co.kr
5. Insert the Highlight Tag
1) Special Tag will be inserted on recorded files, if you press
Highlight tag button.
2) You can easily find the important moment by using highlight
Tag function.
6. Auto Focus
Focus on special object automatically.
You can choose among 2 modes in configuration setting (config.exe).
1) Fixed Mode: Focus will be fixed on user’s chosen working distance(cm)
2) Continuous Mode: Focus will be automatically matched whilst working
7. Zoom-in & Zoom-out
1) Digital zoom-in and zoom-out function
There are 4 steps of magnifications
(1.0x 1.5x 2.0x 3.0x).
2) Not feasible while recording is on.
8. Check Video by Video-out port
1) Prepare TV with HDMI port and change the input to HDMI.
Video-Out 케이블
①TV
②Video-Out port of main body
③Head Assembly Unit
M.B
CAMERA SYSTEM (LooksCAM2) 24 www.xenosys.co.kr
2) Connect Video out cable to ②Video-Out of main body port.
3) Connect the head assembly unit to main body, and turn on while Micro SD card is inserted.
4) If the battery power is enough, system initialization will proceed, and then LED on [REC] button
will come up which is completed system initialization.
5) Video shown by camera will appear on TV with OSD (On Screen Display).
6) You can check real time video by Video-Out port
WARNING:
- There can be system malfunction possibility when you connect LC2-VOC during recording
or LC2-CU is power on. It is due to the difference between two devices electricity, so
connect LC2-VOC first then turn on the power of LC2-CU.
9. Battery Status LED
1) Battery status LED change and operating time by each step
(LED intensity 3 step, recording ON: 4 hours 20 minutes)
No. LED LED status color duration time for
each step
Operating time by LED status
color
1 Green About 1 hour 4 hours 20 minutes
~ 3 hours 20 minutes
2 Orange About 2 hours 3 hours 20 minutes
~ 1 hours 20 minutes
3 Blinking
Orange
About 1 hour then 1 warning sound 1 hour 20 minutes
~ 20 minutes
4 Blinking
Orange
About 20 minutes then 1 warning
sound. After that shout down of power
off
20 minutes ~ Power Off
① Battery Status LED
CAMERA SYSTEM (LooksCAM2) 25 www.xenosys.co.kr
2) Battery status LED change and operating time by graph
Green 1 hour
Orange 2 hours
Blinking Orange 1 hour
Blinking Orange 20
mins OFF
Operating time by
each status LED
color
4 hrs 20 mins
~ 3 hrs 20
mins
3 hrs 20 mins
~ 1 hr 20 mins
1 hr 20 mins
~ 20 mins
20 minutes
~ Power off
Warning Sound None None 1 time 1 time
CAMERA SYSTEM (LooksCAM2) 26 www.xenosys.co.kr
THE VIEWER
1. WiFi Connection
Connect the main body (LC2-CU) to tablet PC (Android/iOS) by WiFi follwing below procedure.
1) Connect the head assembly unit to ①main body, and turn on while Micro SD card is inserted.
2) If the battery power is enough, system initialization will proceed.
3) LED on ② [REC] button will come up which is completed system initialization.
4) After the system initialization, ③Snapshot button of LED should be turned on.
5) If ③Snapshot button of LED is not turned on, it shows WIFI connection is wrong or error.
In this case, start the procedure “1)” again.
6) Connect WIFI name “LooksCam2”.
Default password is”1234567890”.
②REC button
③Snapshot button
①Main Body
Head Assembly Unit
CAMERA SYSTEM (LooksCAM2) 27 www.xenosys.co.kr
2. How to install the Viewer
1) You can check real time video of main body (LC2-CU) by tablet PC Viewer.
2) Recommended Viewer specifications (Firmware, Hardware, Memory, and etc)
Android – RAM: 1.0 GB (Recommended more than 2GB)
More than Android OS 7.0
Monitor Resolution more than 1440 × 2560
iOS – More than iOS 11.0
More than IPhone 6
More than IPad 2 Retina
3) Install the application: Android at Playstore, iOS Appstore to find “LooksCAM2”.
3. Features & Fuctions of Viewer
⑤ Remote Controller
① Network & Status of screen ② Status of Main Body ③ Version ④ Configuration option
⑧ Volume of speaker ⑩ Screen Control ⑪ Recording
(Android/iOS)
⑨ Screen Edit ⑫Menu
⑬ Screen (Live or file play)
⑥ Lock
⑦ Refresh
CAMERA SYSTEM (LooksCAM2) 28 www.xenosys.co.kr
Name Function
①Network & Status
of screen
Display WiFi connection status, zoom-in / zoom-out, and recording status.
WiFi connection trying
WiFi connected. Digital zoom 1x
WiFi connected. Recording is on,
Digital zoom 1x. Recording time.
②Status of Main
Body
Remaining battery status &
remaining storage of SD card
③Version
Firmware version of main body
(LC2-CU) and Viewer version of
tablet PC.
④Configuration Configuration setting of main body. (Refer to 4. Detail Options)
⑤Remote
Controller
Same function like remote controller (LC2-RC).
는 “Focus” or “Zoom”
Function will be chose by the selection of each
action.
⑥Lock Lock the screen touch and lower viewer buttons (from ⑧ ~ ⑫).
⑦Refresh Refresh Live screen to play new one
⑧Volume of
Speaker Control the volume of tablet PC speaker
⑨Screen Edit
Select specific period from video file to store new one (5~30
seconds).
Select time and press “30 sec” to store. (Stored in tablet PC))
Insert the tag (message) while recording is going on.
Save the captured image from Live or video file playing.
⑩Screen Control Press menu to play (or stop) the video file from SD card or tablet PC.
⑪Recording Recording start / stop (Stored in tablet PC)
⑫Menu Choose among Live, SD card file, tablet PC file
(Refer to “5. Button details on menu”)
⑬Screen Playing screen of Live or video file
CAMERA SYSTEM (LooksCAM2) 29 www.xenosys.co.kr
4. Detail Options / Configurations
(1) Language Setting: Choose which language will be used for control unit notices..
(2) WiFi : There are two modes Ap and Station.
A. Ap Mode: Direct connected mode between LC2-CU and tablet PC.
1) BAND: Choose between 2.4GHz and 5GHz.
2) Default Value: SSID(LooksCam2), PASSWORD(1234567890)
3) SSID & password can be discriminated number, capital letter, and small letter. Below rules
should be followed to meet SSID & password.
Channel can be chosen from 0 to 11.
B. Station Mode: Connected to wireless router with LC2-CU & tablet PC.
1) Using the mirroring function of tablet PC, you can transfer the video to TV or monitor wirelessly.
For this function, Chromecast for Android, and Apple TV for iOS.
Connection between LC2-CU and normal PC by using “reflector3” – paid commerical program
to do mirroring.
2) Default Value: SSID (LooksCam2), PASSWORD (1234567890). SSOD and password can be
changed according to wireless router status.
⑵
⑴
⑷
⑶
⑸
⑹
⑺
⑻
CAMERA SYSTEM (LooksCAM2) 30 www.xenosys.co.kr
WARNING:
- When lots of wifi channels around are duplicated, wifi signal can be lower and disconnected on
real time video. Then download Wifi Analyzer or etc. application to diagnose not congested channel
to move and apply to LooksCAM2.
(3) Resolution: Set up for resolution 1080p or 720p
(4) Image Control: Set up for image color by manual or automatic (Recommend for automatic)
(5) Lens
1) Input the 3 digit of product ID code which is marked at LC2-HA lens (Ex, A180138 => input 138)
2) If LC2-HA has been changed, make sure to input new serial number.
(6) AF Mode
1) Continuous: Automatic focus according to the user’s movement
2) Manual(Fixed Mode): Fixed focus at user’s selected WD(cm)
3) At manual mode, press AF button, then it will focus on special object.
4) At manual mode, press & hold AF button, then it will focus on set up WD at “AF Mode” of viewer
setting.
(7) LED LIGHT: Set up the brightness of LC2-CU during the booting process.
(8) MIC, Speaker: Adjust main body microphone and speaker volume.
5. Button Details on Menu
SSID
Minimum digit 6
Maximum digit 12
Allowed letters
English: a-z, A-Z
Number: 1-0
Special character: '_',
Password
Minimum digit 8
Maximum digit 12
Allowed letters
English: a-z, A-Z
Number: 1-0
Special character: '_',
Channel Choose from 1-11. ”0” is automatic channel.
CAMERA SYSTEM (LooksCAM2) 31 www.xenosys.co.kr
(1) LIVE: Real time view from the camera main body
(2) LOOKSCAM STORAGE: Check stored files in SD card of main body.
(3) Documents: Check stored files in tablet PC.
BASIC TROUBLESHOOTING
WARNING before asking for after-sales services:
Symptom Troubleshooting Repair
Cannot turn on.
Cannot charge properly.
Check the connection status
between the cradle and battery
pack or between main body
and battery pack.
Foreign debris may cause the
power off or charging problem
at USB slot.
Clean the charging port and
use again
Clean USB slot
Button input is not possible
during the usage
Check the power switch has
been moved to “Hold” mode.
Re-assemble the battery pack
If malfunction continues,
contact local distributor or
manufacturer
Important data which are stored in LooksCAM2 must be moved or downloaded to other devices or
personal computer periodically. All data can be deleted for after-sales services.
Important data must be backed up by the user before applying after-sales services.
Xenosys will NOT do any separate back-up for recorded files by regarding the user had already
downloaded their files. Please note that all responsibilities related to the data belong to the user or
customer.
Xenosys will provide the circuit diagram, list of components, explanation for repair (any corrected
explanation needed), and other information, if requested.
20180813
20180827
CAMERA SYSTEM (LooksCAM2) 32 www.xenosys.co.kr
and turn on the power
Heat comes out during the
usage
Lot of current is needed to run
this product, so heat comes
out after long time of usage.
This symptom does not affect
the lifespan or quality.
Normal
Light intensity is weak after
the change of battery pack
Check the intensity step is
properly adjusted.
Change the intensity step
properly
Battery discharging time is
fast
Check if battery has been fully
charged.
(Check the battery status LED)
Battery pack is expendables,
so the lifespan will be shorter
than the first-time purchase
after certain period of time.
If the discharging time is fast
even fully charged status, it
means the battery lifespan has
been dead. We recommend
exchanging new battery pack.
LED light flickers sometimes
or intermittently
Check the contact looseness
of connection part of phone
jack
Contact local distributor or
manufacturer
Wifi connection is bad
Download WiFi Analyzer
application or other proper
surveillance program to find
out less traffic channel to
change LooksCAM wifi.
Not occupied channel or less
traffic channel to change
LooksCAM wifi. (Refer to page
22)
DC power supply is always
green color on indicator
It is normal to show green light
on DC power supply as it
shows the power ON.
CAMERA SYSTEM (LooksCAM2) 33 www.xenosys.co.kr
SPECIFICATIONS
1. Measurement & Weight
(1) Control Unit (LC2-CU)
1) Measurement: Refer to below photo
2) Weight: 68 g
(2) Battery Pack (BTP-LC2)
1) Measurement: Refer to below photo
2) Weight: 217 g
(3) Head Assembly Unit (LC2-HA)
1) Measurement: Refer to below photo
2) Weight: 41 g (Except LED lens & cable)
(4) Remote Controller (LC2-RC)
1) Measurement: Refer to below photo
2) Weight: 59 g
CAMERA SYSTEM (LooksCAM2) 34 www.xenosys.co.kr
(5) DC POWER SUPPLY
(DC Power Supply, FW8000MUSB05)
1) Measurement: 31(L)x41(W)x77(H) [mm]
2) Weight: 81 g
* Always shows green color (power indicator)
(6) USB Power Cable (LC2-USBC)
1) Measurement: 2 m
2) Weight: 44 g
(7) Video-Out Cable (LC2-VOC)
1) Measurement: 3.6 m
2) Weight: 152 g
CAMERA SYSTEM (LooksCAM2) 35 www.xenosys.co.kr
2. Detailed Specifications
Specification
Rated Input Voltage DC3.6V
Image Sensor 1/3 inch 4.0M Pixel CMOS
Recording Resolution Full HD 1920*1080p
FOV (Crosswise) f14mm Lens : Ø137mm @ WD 400mm
f20mm Lens : Ø 94mm @ WD 400mm
Recording Frame 30fps
Video Quality (Bitrate) CBR type 10 Mbps
WiFi streaming Rec (EIS) + WiFi: 1920*1080/30fps, delay 1.8sec.
Rec (EIS) + WiFi + HDMI: 480*360p / delay 1.8sec
Digital Zoom 1.0x 1.5x 2.0x 3.0x
Video Compression H.264
Audio Codec AAC (Advanced Audio Coding), 12 KHz
Function Button REC/Snap shot/LED
Speaker Built-in 8 ohm
Micro SDHC Card
128GB Micro SDHC Card, More than Class 10, MLC Type
File System: FAT32, File Allocation Size: 32KB
File Length: 30 minutes (About 2.5GB)
Operating Temperature /
Storage Temperature 6℃ - 40℃ / 10℃ - 40℃
Consecutive Recording Time
(LED light 3 step, WiFi On status)
4 hours 20 minutes
LED 2 step: 6 hours 20 minutes
LED 1 step: 7 hours 20 minutes
Full Charging Time (Capacity) 6 hours (10.50 Ah)
Input power of
DC POWER SUPPLY 100-240 V~, 50-60 Hz, 0.3A
Output power of
DC POWER SUPPLY 5.0V 2.2A
Battery Input Power 5.0V 2.2A
LED Illumination
Brightness &
Current Consumption
STEP lx @WD400mm
1st 19,000
2nd 30,000
CAMERA SYSTEM (LooksCAM2) 36 www.xenosys.co.kr
3rd 39,000
Field of View Size (mm) @WD400mm Ø82 (Standard)
Weight(g) 25 g
Color Temperature, Spectrum 6000 K, 400 - 700 nm(Visible Ray)
Uniformity More than 80% @WD400mm
LED Operating Power 2W (max.)
LED Life Time (Guaranteed) 50,000 hours
LED Source High power LED (White color)
Replacement Components
Battery Pack DC3.6V 10.05 Ah (Lithium ion)
DC POWER SUPPLY Input: 100-240 V~, 50/60 Hz, 0.3A
Output: DC5.0V 2200mA
Dimension & Total Weight of Package
Dimension W 410 x H 320 x T 180 (mm)
Total Weight 3.80 kg (With total outer package 4.30 kg)
3. Label for packaging & components
1) Outer Box
CAMERA SYSTEM (LooksCAM2) 37 www.xenosys.co.kr
2) Main Body
3) Remote Controller
4) Battery Pack
ELECTROMAGNETIC COMPATABILITY
Electromagnetic Compatibility
It is designed to protect the medical equipment from the harmful interruption. This system occur
electromagnetic interruption within the acceptable range. And, if it is not installed nor used properly
to the direction, it may generate radio wave energy to cause any harmful interruption to some other
equipment around. It cannot guarantee that the interruption will not give any influence to specific
equipments. When the device is powered on, you can find out if it generates electromagnetic
interruption or not.
Recommend to choose one and more ways to solve the trouble in the following ways.
1. Relocate the equipments receiving the interruptive wavelength.
2. Put the each equipment in longer distance.
3. Connect the equipment to the different outlets from the ones connected to other equipments.
CAMERA SYSTEM (LooksCAM2) 38 www.xenosys.co.kr
4. If you need expert’s help, contact to manufacturer or professional distributor.
TRANSPORTATION
1. To protect LooksCAM2 from any damage in transportation, pack it by plastic bubble wrap or
shipping box.
2. Load LooksCAM2 boxes up and down evenly by handcart and any vehicle trunk to transport.
3. When you carry LooksCAM2 by hand, hold it with two hands firmly and disconnect charger, and
power cord from the main body for safe transportation.
STORAGE
1. Maintain the following conditions for storing main products & components.
Environment for Operating & Storage
Ambient Temperature 6℃ - 40℃
Relative Humidity RH30 - 85%
Pressure 860 hPa - 1060 hPa
Environment for Transportation & Storage (Non-operating)
Ambient Temperature 10℃ - 40℃
Relative Humidity RH30 - 85%
Pressure 860 hPa - 1060 hPa
- External box marking will be as follows.
1. Do not pull out, twist, nor bend excessively the power cord.
2. Wind up the power cord loosely, and store it by using the rubber bandage or cable tie.
3. Do not expose the main body to excessive shock, direct ray of light and high temperature which
may cause the defective reason.
4. Caution for battery storage: As Li-ion battery is small-sized with high power, if it is stored fully
charged condition for a long time, the battery lifespan can be reduced.
① Store it under half-charged condition in case of non-use immediately.
② Store the battery with separated from the main body in case of long-time no use.
③ Recommend to keep it in the dry condition with ambient temperature range of +15℃ - +25℃.
Keep away from too hot or extremely cold places.
10 ℃
40 ℃
860 hPa
1060 hPa
30 %
85 %
CAMERA SYSTEM (LooksCAM2) 39 www.xenosys.co.kr
CLEANING INSTRUCTIONS
1. Clean up the surface of LED lens module & camera lens by soft cloth with neutral detergent
regularly to remove dirt, and leave it dry for usage.
2. Do not use volatile chemicals like benzene, alcohol, thinner, and acetone for cleaning. If there
is any contact of these chemicals to the surface, clean it by soft cloth dipped with neutral
detergent. However, the manufacturer is not responsible for any defect caused by these
chemicals.
3. Do not expose the equipment to the sterilizing or cleaning process with excessive temperature
and humidity. In case of the exposure, it will cause the damage to the equipment and out of
warranty. Especially, inside parts of the main body do not allow the contact of any liquid.
SERVICES & WARRANTY
1. This service & warranty statement applies to all countries to the extent that there is no special
warranty rule.
2. All services & warranty should be provided by Xenosys Co., Ltd. or authorized personnel by
Xenosys Co., Ltd.
3. Warranty becomes effective from the sales date for material, production defective, or defect under
the normal use. Thus the warranty period starts from the first purchaser’s sales date. Warranty
will not be applied for abuse, improper use, negligence, improper installation, and operation or
any remodeling, adjustment and modification by unauthorized personnel or technician. Refer to
the warranty period in line #13.
4. The warranty period of the battery pack and Micro SD card (expendables) is 6 months from the
date of purchase.
5. Exchanged or any broken part after repair become to the property of Xenosys Co., Ltd.
6. There is no extended or renewed warranty period after the repair or replacement is done.
7. No warranty will be applied in case of the modification or personalized part by customer’s request.
8. No warranty will be applied in case of no serial number or hard to detect the proper one.
9. Changes in this limited warranty require the previous approval from Xenosys Co., Ltd.
10. If there is any defect happens which cannot be handled by troubleshooting in this manual, return
it to the manufacturer. Then Xenosys will take care of it. If the qualified engineer determines that
the defect comes from the abuse or improper use, warranty will not be applied. The repair cost
shall be notified prior to the service & repair work starts.
11. Before sending the equipment need for repair, contact the manufacturer or distributor. Then the
manufacturer or distributor will report details with RMA No. and related reference which will make
easier to track.
12. There are no user serviceable parts in this product. Please send the product to the distributor
(dealer) for servicing. Technical description or manual is available upon request.
13. Warranty Period of LooksCAM
1) LooksCAM (except the battery & non-Xenosys provided parts): 1 year
CAMERA SYSTEM (LooksCAM2) 40 www.xenosys.co.kr
2) Battery & Micro SD Card: 6 months
EU Representative (EU Repräsentant)
1. Company: Cormedics Medizintechnik GmbH
2. Address: Bahnhofstr. 32, 82041 Deisenhofen, Germany
3. Tel (Fon): +49 (0)89 666 58 79 15
4. Fax: +49 (0)89 54 999 030
5. E-mail: a.huettl@cormedics.com
6. Web: http://www.cormedics.com
CAMERA SYSTEM (LooksCAM2) 41 www.xenosys.co.kr
※ Revision List
Version No. Release date Revision
Version 1.0 May, 2019 First release