Post on 28-Jun-2020
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page1of14
iPhone 6 Plus Full Display Assembly
Replacement INTRODUCTION Use this guide along with the Werx Repair Mat to replace the cracked or broken screen on your iPhone 6 Plus. Follow Werx Repair Mat Steps 1,2,4 to disassemble. Reverse steps for re-assembly. Use this guide to strip and replace your iPhone 6 Plus front panel. It will show you how to remove the home button, front-facing camera and sensor assembly, LCD shield plate, and home button ribbon cable. TOOLS: IMPORTANT Take your time! The repair takes about 15-30 minutes.
Remember that you will be handling fragile parts, so be gentle!
Most screws are different sizes so keep them organized.
Werx Repair Mat
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page2of14
Step 1: Pentalobe Screws
• Before disassembling your iPhone, be
sure it is powered off.
• Remove the two 3.6 mm Pentalobe
screws next to the lightning connector.
Step 2: Front Panel Assembly
• While holding the iPhone down with
one hand, insert a plastic opening tool
and begin gently pry the rear case
down, away from the display assembly.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page3of14
Step 3:
• Pull the home button end of the front
panel assembly away from the rear
case, using the top of the phone as a
hinge.
Keep the front panel supported at a 90
degree angle in relation to the rear
case.
Step 4:
• Use the Werx Repair Mat to keep
screws organized and prevent screw
misplacement damage
• Remove the following five Phillips
screws securing the front panel
assembly cable bracket:
o Three 1.2 mm Phillips screws
o One 1.7 mm Phillips screw
o One 3.1 Phillips screw
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page4of14
Step 5:
• Remove the front panel assembly cable
bracket from the logic board.
Step 6:
• Using a plastic opening tool disconnect
the front-facing camera and sensor
cable connector.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page5of14
Step 7:
• Using a plastic opening tool disconnect
the home button cable connector.
Step 8:
• Using a plastic opening tool disconnect
the digitizer cable connector.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page6of14
Step 9:
• Finally, using a plastic opening tool
disconnect the display data cable
connector.
• Remove the front panel assembly from
the rear case.
Step 10: Home Button
• Remove the two 1.8 mm Phillips
screws securing the home button
bracket.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page7of14
Step 11:
• Remove the home button bracket from
the front panel.
Step 12:
• Remove one 1.7 mm Phillips screws
securing the LCD shield plate to the
front panel
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page8of14
Step 13:
• Using the plastic opening tool
disconnect the home button cable
connector by pushing it up and away
from the home button.
Step 14:
• Use the plastic opening tool to carefully
separate the home button cable from
the adhesive securing it to the front
panel.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page9of14
Step 15:
• Once all the adhesive has been
separated, remove the home button
from the front panel.
Step 16: Home Button
• Insert the home button to the front
panel.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page10of14
Step 17:
• Connect the home button cable
connector.
Step 18:
• Insert the home button bracket from the
front panel.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page11of14
Step 19:
• Insert the two Phillips screws securing
the home button bracket.
Step 20:
• Insert the LCD assembly to the rear
case.
• Connect the following flex cable to the
logic board:
o Display data cable
o Digitizer cable
o Home button cable
o Front-facing camera and censor
cable
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page12of14
Step 21:
• Insert the front panel assembly cable
bracket to the logic board.
Step 22:
• Insert five Phillips screws to securing
the front panel assembly cable bracket.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page13of14
Step 23:
• Align the clips just below the top edge
of the rear case. Then, slide the front
panel upward until its top edge is flush
with the rear case.
Step 24:
• Run your fingers along the sides being
sure the assembly slips evenly into the
frame.
iPhone6PlusFullDisplayAssemblyReplacement
WerxParts www.werxparts.com Page14of14
Step 25: Pentalobe Screws
• Insert the two Pentalobe screws next to
the lightning connector.