Post on 31-Aug-2019
4578346300/AA
1
Adjusting the legs (*optional)If your refrigerator is unbalanced;You can balance your refrigerator by turning the legs of it as illustrated in the figure. The corner where the leg exists is lowered when you turn in the direction of black arrow and raised when you turn in the opposite direction. Taking help from someone to slightly lift the refrigerator will facilitate this process.* If the subject parts are not included in the product you have purchased, then it is valid for other models.
The backwall of the wooden cabinet must be left open completely to kitchen wall in order to allow sufficient air circulation to cooldown the condenser unit for energy efficiency.
1775
629
1001
min. 200 cm2
1778
-178
8
71
40
545540
min. 56017
75
32
16
100
100 60
60
No woodenBackwall
min. 555
Füße einstellen (*optional)Wenn Ihr Kühlschrank nicht absolut gerade steht:Sie können den Kühlschrank – wie in der Abbildung gezeigt – durch Drehen der Füße ausbalancieren. Wenn Sie in Richtung des schwarzen Pfeils drehen, senkt sich die Ecke, an der sich der Fuß befindet. Beim Drehen in Gegenrichtung wird die Ecke angehoben. Diese Arbeit fällt erheblich leichter, wenn ein Helfer das Gerät etwas anhebt.* Falls Teile nicht zum Lieferumfang des erworbenen Produktes zählen, gelten sie für andere Modelle.
Die Rückseite des Holzschranks muss zur Küchenwand hin vollständig offen bleiben, damit eine ausreichende Luftzirkulation für die Abkühlung des Kondensators zur Gewährleistung der Energieeffizienz sorgt.
7140
200 cm2
min 200 cm2
min.50 mm
min.10 mm
min.50 mm
629
1001
16
2
3
90°
1
Note: Installation step for 2, screws for connecting top plastic part should not be screwed very hard, because of moving the plastic part easily left or right side.Hinweis: Installationsschritt 2: Die Schrauben zum Fixieren des Kunststoffteils sollten nicht zu fest angezogen werden, da sich das Kunststoffteil ansonsten nach links oder rechts verschieben kann.
2
PS
* Spares Included* Ersatzteile inklusive
1
34
Torx(T)x4
Wood(W)x22
Plastic Sheet(PS)x4
Wood(1TW)x10
4
5 6
7 8
(2T)
(2T)
9
10
40.5 mm
40.5 mm
(1TW)
5
11 a 11 b
12
13 14 a
40,5 mm
40,5 mm
(1TW)
14 b 15
6
40.5 mm
40.5 mm
(2TW)
40.5 mm
40.5 mm
(2TW)
(2W)
7
16 17
18
8,5
8,5
11
8
2 box x
1 x 2 x 2 x 2 x
2 x 2 x 2 x 1 x
19
9
20
21 22
10
23
X
A A
E
A = 2 mm is recommended.Top view
Ansicht von oben A = 2 mm empfohlen
11
24
X W
y W
C=(HD1) - (X)y=1072 - (HD3) - (C)
HD
3
CHD
1
CHD
1
12
25
26
13
27 a
27 b
14
27 c
27 d
(2Wx4)
A2
A2 A2
A1=A2
A1=A2
A1
A2A1
A2
15
28 29
30
31
2 mm
2 mm
2 mm
16