Post on 09-Sep-2020
Honda Dealer: Please give a copy of these instructions to your customer.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2018 American Honda Motor Co., Inc. - All Rights Reserved.
PARTS LIST
87959-MKC-A0001 of 12
Publication No.
MII 16426
Issue Date
January 2018
HOMELINK®
P/N 08U77-MKC-A00 GL1800/B/BD/D/DA
No. Description Qty
(1) Installation instructions URL 1
(2) Homelink® unit 1
(3) Sub harness 1
(4) Homelink® knob set 1
(5) 4 mm screw 2
(3)
(4)
(1)
(2)
(5)
TOOLS AND SUPPLIES REQUIREDPhillips screwdriver
Dish soap solution (Water:Dish soap / 100:1)
Shop towel
Torque wrench
Item N·m kgf·m Ibf·ft
4 mm screw 1 0.1 0.7
TORQUE CHARTTighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.
INSTALLATION CAUTION
• To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory.
NOTE:
• Disconnect the negative (-) cable from the battery before installing this accessory.
• The memory of the clock will be erased when you disconnect the battery. Reset the clock after reconnecting the battery.
• Reinstall the removed parts on the motorcycle and make sure that the wires and harnesses are not pinched.
• Although the illustration is of GL1800/D/DA, use the same procedures for other models.
1. Open the left saddlebag lid as shown.
• Repeat on the right side.
HOMELINK 1 KNOB
HOMELINK 2 KNOB
<Left side>
LEFT SADDLEBAG LID
2. Remove the lef t s ide cover as shown, and disconnect the negative (-) cable of the battery.
LEFT SIDE COVER
2 of 12
3. Remove the right side cover in the same manner as the left side.
4. Remove the seat as shown.
• Disconnect the connector for GL1800/D/DA.
BOLT
WASHER
SEAT
5. Remove the right and left rear top lid as shown.
• Perform this step on GL1800B/BD only.RIGHT REAR TOP LIDLEFT REAR TOP LID
7. Remove the center rear top cover as shown.
• Perform this step on GL1800B/BD only.
6. Remove the parts as shown.
• Perform this step on GL1800B/BD only.
SCREW
CENTER REAR TOP COVER
CENTER REAR TOP COVER
CLIP
3 of 12
8. Remove the right and left passenger grip as shown.
WASHER
BOLT
RIGHT PASSENGER GRIP
CABLE
LEFT PASSENGER GRIPRemove the cable.
9. Remove the right pillion step holder cover as shown.
<Right side>
BOLT
SCREW
RIGHT PILLION STEP HOLDER COVER
CLIP
10. Fold down the left rear view mirror backward as shown.
<Left side>
LEFT REAR VIEW MIRROR
11. Remove the left mirror arm panel as shown.
<Left side>
LEFT MIRROR ARM PANEL
SCREW
12. Remove the left rear view mirror as shown.
BOLT
LEFT REAR VIEW MIRRORDisconnect the connector.
13. Remove the right mirror arm panel and right rear view mirror in the same manner as the left side.
4 of 12
14. Remove the screw as shown.
• Repeat on the right side.
16. Remove the clip as shown.
17. Remove the left inner cowl as shown.
15. Remove the left deflector panel as shown.
<Left side>
SCREW
SCREW
LEFT INNER COWL
CLIP
CLIP
SCREW
<Left side>
SCREW
LEFT DEFLECTOR PANEL
CLIP
19. Remove the left middle cowl as shown.
<Left side>
LEFT MIDDLE COWL
<Left side>
18. Remove the clip as shown.
CLIP
20. Remove the right deflector panel, right inner cowl and right middle cowl in the same manner as the left side.
5 of 12
21. Remove the parts as shown.
• Repeat on the right side.
23. Remove the clip and disconnect the connector as shown.
22. Remove the 2P black connector as shown.
<Right side>
2-PIN WATERPROOF CONNECTOR (Black)
CLIP
2-PIN WATERPROOF CONNECTOR (Black)
<Left side>
SCREW
SCREWCOLLAR
24. Remove the right outer air guide as shown.
25. Remove the pocket cable as shown.
SCREW
CLIPRIGHT OUTER AIR GUIDE
POCKET CABLE
SCREW
6 of 12
26. Remove the parts as shown.
27. Remove the shelter as shown.
SCREW
CLIP
CLIP
SHELTER
28. Remove the center switch panel as shown.
SCREW
CLIP
CENTER SWITCH PANELDisconnect the connector.
29. Remove the right and left center console panel as shown.
RIGHT CENTER CONSOLE PANEL
LEFT CENTER CONSOLE PANEL
CENTER SWITCH PANEL (Back side)
SCREW
SCREW
7 of 12
31. Remove the dummy switch as shown.
CENTER SWITCH PANEL
SCREW (Save)
DUMMY SWITCH (Save)
30. Remove the center console garnish as shown.
CENTER SWITCH PANEL
CENTER CONSOLE GARNISH
SCREW
33. Install the center console garnish, right and left center console panel in the reverse order of removal.
34. Install the center switch panel in the reverse order of removal.
35. Open the rear trunk lid as shown.
• Perform this step on GL1800/D/DA only.• Refer to the Owner’s Manual and using an
emergency trunk cable to open the rear trunk lid.
32. Install the Homelink® knobs as shown.
CENTER SWITCH PANEL
HOMELINK 1 KNOB
HOMELINK 2 KNOB
REAR TRUNK LID
8 of 12
36. Remove the USB cord as shown.
• Perform this step on GL1800DA only.
USB CORD
38. Remove the trunk front lower panel as shown.
• Perform this step on GL1800/D/DA only.
TRUNK FRONT LOWER PANEL
37. Remove the parts as shown.
• Perform this step on GL1800/D/DA only.
<GL1800DA>
TRUNK HOLDER
SCREW
40. Remove the trunk right side cover as shown.
• Perform this step on GL1800/D/DA only.• Repeat on the left side.
<Right side>
TRUNK RIGHT SIDE COVER
39. Remove the parts as shown.
• Perform this step on GL1800/D/DA only.• Repeat on the left side.
SCREW
SCREW
CLIP
CLIP
9 of 12
41. Remove the clips as shown.
• Repeat on the right side.<Left side> GL1800/D/DA
<Left side> GL1800B/BD
43. Remove the rear fender as shown.
SCREW
REAR FENDERDisconnect the connector.
SCREW
TRUNK CENTER LOWER COVER
2-PIN WATERPROOF CONNECTOR (Black)
42. Disconnect the 2P black connector and remove the trunk center lower cover as shown.
• Perform this step on GL1800/D/DA only.
CLIP
CLIP
44. Remove the saddlebag rear center cowl as shown.
SCREW
SADDLEBAG REAR CENTER COWL
10 of 12
45. Remove the parts as shown.
<Right side>
BOLTWASHER
SCREW
46. Remove the screws as shown.SCREW
SCREW
47. Move the right saddlebag catch as shown.
RIGHT SADDLEBAG CATCH
48. Remove the radio antenna as shown.
RADIO ANTENNA
SCREW
RIGHT SADDLEBAG CATCH
11 of 12
53. Move the right saddlebag and route the sub harness as shown.
BOOTMove.
SUB HARNESS
SUB HARNESS
GROMMETInsert into the hole.
51. Install the Homelink® unit as shown.
PLUG (Save)
HOMELINK® UNIT
4 mm SCREW
RIGHT SADDLEBAG CATCH
50. Remove the plug as shown.
49. Remove the emergency trunk cable as shown.
• Perform this step on GL1800/D/DA only.
EMERGENCY TRUNK CABLE
RIGHT SADDLEBAG CATCH
GROMMET
52. Apply dish soap solution to the grommet at the position shown.
DISH SOAP SOLUTIONApply.
SUB HARNESS
12 of 12
57. Route and connect the sub harness as shown.
8-PIN WATERPROOF DUMMY CONNECTOR (Gray) (Save)
8-PIN WATERPROOF CONNECTOR (Gray)
SUB HARNESS
58. Install the motorcycle’s parts in the reverse order of removal.
• Confirm that any wire harness is not caught or too tight.
59. Check the Homelink®, headlight and the other lights for proper operation.
54. Connect the sub harness to the Homelink® unit as shown.
55. Install the right saddlebag, emergency trunk cable and right saddlebag catch in the reverse order of removal.
56. Remove the dummy connector as shown.
HOMELINK® UNIT
SUB HARNESS
MOTORCYCLE’S HARNESS