NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD CMAx

WITH 4.3” MYFORD SCREEN2013-2016

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD EDGE

WITH 4.3” MYFORD SCREEN2011-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ESCAPE

WITH 4.3” MYFORD SCREEN2013-2015

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ExPLORER

WITH 4.3” MYFORD SCREEN2011-2015

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD F150

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FLEx

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FOCUS

WITH 4.3” MYFORD SCREEN2012-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TAURUS

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT CONNECT

WITH 4.3” MYFORD SCREEN2014-2016

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT

WITH 4.3” MYFORD SCREEN2015-2016

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD CMAx

WITH 4.3” MYFORD SCREEN2013-2016

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD EDGE

WITH 4.3” MYFORD SCREEN2011-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ESCAPE

WITH 4.3” MYFORD SCREEN2013-2015

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ExPLORER

WITH 4.3” MYFORD SCREEN2011-2015

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD F150

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FLEx

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FOCUS

WITH 4.3” MYFORD SCREEN2012-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TAURUS

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT CONNECT

WITH 4.3” MYFORD SCREEN2014-2016

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT

WITH 4.3” MYFORD SCREEN2015-2016

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2014Ford EconolinE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford EconolinE 2008-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford EconolinE 2008-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford EconolinE 2008-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER DASH, UNDER THE RADIO

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford EconolinE 2008-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford EconolinE 2008-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2010Ford EdgE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford EdgE 2007-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford EdgE 2007-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford EdgE 2007-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford EdgE 2007-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford EdgE 2007-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2012Ford EscapE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford EscapE 2008-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford EscapE 2008-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford EscapE 2008-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGEJUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford EscapE 2008-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford EscapE 2008-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2014Ford ExpEdition

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford ExpEdition 2007-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford ExpEdition 2007-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford ExpEdition 2007-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford ExpEdition 2007-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford ExpEdition 2007-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2010Ford ExplorEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford ExplorEr 2006-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford ExplorEr 2006-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford ExplorEr 2006-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : WHITE/BROWNCENTER CONSOLE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford ExplorEr 2006-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford ExplorEr 2006-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2010Ford ExplorEr sport trac

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford ExplorEr sport trac 2006-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford ExplorEr sport trac 2006-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford ExplorEr sport trac 2006-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : WHITE/BROWNCENTER CONSOLE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford ExplorEr sport trac 2006-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford ExplorEr sport trac 2006-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2010Ford F-sEriEs supEr duty

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F-sEriEs supEr duty 2008-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F-sEriEs supEr duty 2008-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F-sEriEs supEr duty 2008-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGEPASSENGER SIDE, NEXT TO GLOVE BOX

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F-sEriEs supEr duty 2008-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F-sEriEs supEr duty 2008-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2011-2016Ford F-sEriEs supEr duty

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F-sEriEs supEr duty 2011-2016

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F-sEriEs supEr duty 2011-2016

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F-sEriEs supEr duty 2011-2016

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F-sEriEs supEr duty 2011-2016

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F-sEriEs supEr duty 2011-2016

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2009-2010Ford F150

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F150 2009-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F150 2009-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F150 2009-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER DASH, UNDER THE TRAY

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F150 2009-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F150 2009-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2011-2014Ford F150

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F150 2011-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F150 2011-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F150 2011-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F150 2011-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F150 2011-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2007Ford FivE hundrEd

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford FivE hundrEd 2006-2007

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford FivE hundrEd 2006-2007

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford FivE hundrEd 2006-2007

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford FivE hundrEd 2006-2007

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford FivE hundrEd 2006-2007

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2009-2012Ford FlEx

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford FlEx 2009-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford FlEx 2009-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford FlEx 2009-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, JUNCTION CONNECTOR, IN FRONT OF THE SHIFTER

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford FlEx 2009-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford FlEx 2009-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2011Ford Focus

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Focus 2008-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Focus 2008-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Focus 2008-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, HORIZONTAL HARNESS ON THE HEATER BOX

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Focus 2008-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Focus 2008-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2012Ford Fusion

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Fusion 2006-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Fusion 2006-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Fusion 2006-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, IN FRONT OF THE ARM REST

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Fusion 2006-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Fusion 2006-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2012Ford Mustang

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang 2007-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang 2007-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang 2007-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang 2007-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang 2007-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2013-2014Ford Mustang

BasE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang BasE 2013-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang BasE 2013-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang BasE 2013-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang BasE 2013-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang BasE 2013-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2013-2014Ford Mustang

shakEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang shakEr 2013-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang shakEr 2013-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

2

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang shakEr 2013-2014

AUX INAUX IN

2

SUB INCENTER IN

SUB INCENTER IN

AUDIOCABLE

OBDII CONNECTORSTEP 4

MAESTRO RR MODULE

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

CONNECT TOAFTERMARKET RADIO

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

FO1 T-HARNESS

WIRING DIAGRAMSTEP 1

STEP 2

STEP 3

STEP 5

STEP 6

WHITEWHITE/BLACKGRAYGRAY/BLACKGREENGREEN/BLACK

PURPLE/BLACKPURPLE

LF RCA INPUT

RF RCA INPUT

LR RCA INPUT

RR RCA INPUT

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

WIRES FROMVEHICLE

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO:ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang shakEr 2013-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang shakEr 2013-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2013-2014Ford Mustang

shakEr pro

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang shakEr pro 2013-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang shakEr pro 2013-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

2

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang shakEr pro 2013-2014

AUX INAUX IN

2

SUB INCENTER IN

SUB INCENTER IN

AUDIOCABLE

OBDII CONNECTORSTEP 4

MAESTRO RR MODULE

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

CONNECT TOAFTERMARKET RADIO

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

FO1 T-HARNESS

WIRING DIAGRAMSTEP 1

STEP 2

STEP 3

STEP 5

STEP 6

WHITEWHITE/BLACKGRAYGRAY/BLACKGREENGREEN/BLACK

PURPLE/BLACKPURPLE

LF RCA INPUT

RF RCA INPUT

LR RCA INPUT

RR RCA INPUT

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

WIRES FROMVEHICLE

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO:ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang shakEr pro 2013-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang shakEr pro 2013-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2009Ford taurus

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford taurus 2008-2009

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford taurus 2008-2009

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford taurus 2008-2009

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : GRAY/BLUECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford taurus 2008-2009

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford taurus 2008-2009

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2010-2012Ford taurus

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford taurus 2010-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford taurus 2010-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford taurus 2010-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford taurus 2010-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford taurus 2010-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2012Ford taurus x

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford taurus x 2008-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford taurus x 2008-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford taurus x 2008-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford taurus x 2008-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford taurus x 2008-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2009-2012lincoln Mks

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln Mks 2009-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln Mks 2009-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln Mks 2009-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln Mks 2009-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln Mks 2009-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2010-2012lincoln Mkt

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln Mkt 2010-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln Mkt 2010-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln Mkt 2010-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln Mkt 2010-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln Mkt 2010-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2010lincoln Mkx

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln Mkx 2007-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln Mkx 2007-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln Mkx 2007-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln Mkx 2007-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln Mkx 2007-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2012lincoln MkZ

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln MkZ 2007-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln MkZ 2007-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln MkZ 2007-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln MkZ 2007-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln MkZ 2007-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2014lincoln navigator

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln navigator 2007-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln navigator 2007-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln navigator 2007-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGESYNC UNIT, CENTER CONSOLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln navigator 2007-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln navigator 2007-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006lincoln ZEphyr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln ZEphyr 2006

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln ZEphyr 2006

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln ZEphyr 2006

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln ZEphyr 2006

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln ZEphyr 2006

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2011MaZda triButE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MaZda triButE 2008-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MaZda triButE 2008-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MaZda triButE 2008-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MaZda triButE 2008-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MaZda triButE 2008-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2011MErcury MarinEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury MarinEr 2008-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury MarinEr 2008-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury MarinEr 2008-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGEJUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury MarinEr 2008-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury MarinEr 2008-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2011MErcury Milan

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury Milan 2006-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury Milan 2006-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury Milan 2006-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, IN FRONT OF ARM REST

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury Milan 2006-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury Milan 2006-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2005-2007MErcury MontEgo

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury MontEgo 2005-2007

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury MontEgo 2005-2007

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury MontEgo 2005-2007

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury MontEgo 2005-2007

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury MontEgo 2005-2007

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2010MErcury MountainEEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury MountainEEr 2006-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury MountainEEr 2006-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury MountainEEr 2006-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : WHITE/BROWNCENTER CONSOLE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury MountainEEr 2006-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury MountainEEr 2006-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2009MErcury saBlE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury saBlE 2008-2009

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

maestro.support@idatalink.com

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury saBlE 2008-2009

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury saBlE 2008-2009

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : GRAY/BLUECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury saBlE 2008-2009

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury saBlE 2008-2009

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestro.support@idatalink.com

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.