HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox...

301
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. HOW TO USE THIS INSTALL GUIDE 1 2 3 SELECT VEHICLE PRINT PAGES NEEDED

Transcript of HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox...

Page 1: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

Page 2: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD CMAx

WITH 4.3” MYFORD SCREEN2013-2016

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 3: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 4: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 5: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 6: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 7: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD EDGE

WITH 4.3” MYFORD SCREEN2011-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 8: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 9: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 10: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 11: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 12: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ESCAPE

WITH 4.3” MYFORD SCREEN2013-2015

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 13: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 14: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 15: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 16: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 17: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ExPLORER

WITH 4.3” MYFORD SCREEN2011-2015

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 18: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 19: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 20: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 21: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 22: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD F150

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 23: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 24: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 25: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 26: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford f150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 27: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FLEx

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 28: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 29: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 30: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 31: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 32: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FOCUS

WITH 4.3” MYFORD SCREEN2012-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 33: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 34: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 35: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 36: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 37: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TAURUS

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 38: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 39: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 40: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 41: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 42: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT CONNECT

WITH 4.3” MYFORD SCREEN2014-2016

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 43: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 44: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 45: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 46: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 47: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-AS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT

WITH 4.3” MYFORD SCREEN2015-2016

retains steering wheel controls, factory amplifier and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 48: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 49: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

STEP 5• Connect the 4 pin blue plug to the maestro and the other

end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

1

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 50: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 4

BACKUP CAMBACKUP CAM

C

A FG

C

A

G

F

1

E

E

AUX INAUX IN

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

FO2 T-HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

CONNECT TOAFTERMARKET RADIO

SEE AFTERMARKET RADIO GUIDEFOR WIRECOLORS

WIRING DIAGRAM

STEERING WHEELCONTROL CABLE

BROWN (NOT CONNECTED)

WIRES FROMVEHICLE

FACTORY RADIO HARNESSSTEP 2

SCREEN HARNESS ABOVE RADIOSTEP 3

STEP 4 OBDII CONNECTOR

Page 51: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-AS maestro.idatalink.com

ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 52: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

Page 53: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD CMAx

WITH 4.3” MYFORD SCREEN2013-2016

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 54: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 55: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 56: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 57: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford cmax with 4.3" screen 2013-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 58: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD EDGE

WITH 4.3” MYFORD SCREEN2011-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 59: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 60: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 61: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 62: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford edge with 4.3" screen 2011-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 63: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ESCAPE

WITH 4.3” MYFORD SCREEN2013-2015

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 64: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 65: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 66: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 67: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford escape with 4.3" screen 2013-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 68: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD ExPLORER

WITH 4.3” MYFORD SCREEN2011-2015

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 69: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 70: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 71: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 72: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford explorer with 4.3" screen 2011-2015

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 73: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD F150

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 74: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 75: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 76: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 77: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford F150 with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 78: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FLEx

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 79: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 80: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 81: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 82: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Flex with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 83: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD FOCUS

WITH 4.3” MYFORD SCREEN2012-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 84: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 85: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 86: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 87: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford Focus with 4.3" screen 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 88: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TAURUS

WITH 4.3” MYFORD SCREEN2013-2014

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 89: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 90: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 91: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 92: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford taurus with 4.3" screen 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 93: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT CONNECT

WITH 4.3” MYFORD SCREEN2014-2016

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 94: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 95: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 96: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 97: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit connect with 4.3" screen 2014-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 98: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

OPTIONAL ACCESSORIESNone

PROGRAMMED FIRMWAREADS-RR(SR)-FOR02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro FO2 Installation Harness

INSTALL GUIDEFORD TRANSIT

WITH 4.3” MYFORD SCREEN2015-2016

retains steering wheel controls, sync and more!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

Page 99: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

[email protected]

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Page 100: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the F02 T-harness and match the wire functions.

STEP 2

• Connect the factory harness to the F02 T-harness.

STEP 3• Connect the screen harness to the F02 T-harness.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

proceed to module setup.

The module is now ready to be used.

Insert the aftermarket radio in the dashboard housing and test all the functionalities.

Reassemble the dashboard carefully.

OEM BLUETOOTH SETUPOnly one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

1

2013 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned OFF by default. To turn ON the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The Radio will turn on and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select FINISH.

2014 Kenwood Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF.

2014 Alpine Radios:

For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key into the ignition and turn it to the ACC position. The radio will turn ON and the main screen will appear. Select the settings button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE CONNECTION. Two options will be available ON or OFF, select OFF.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

Page 101: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 4

C

A FG

C

A

G

F

1

H

H

AUX INAUX IN

BACKUP CAMBACKUP CAM

D

D

STEP 4 OBDII CONNECTOR

CUT AND REMOVE THE RCA JACKS

STEP 1

MAINHARNESS

RCA CABLES

WIRES FROMVEHICLE

FO2 T-HARNESS

FACTORY RADIO HARNESS

CONNECT ONLY WHENTHERE IS NO SYNC INVEHICLE

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

STEP 2

STEP 5

STEP 6

MAESTRO RR MODULE

ORANGE - PARKING LIGHT (+)PURPLE/WHITE - REVERSE LIGHT (+)LTGREEN - E-BRAKE (-)

YELLOW/BLACK - FOOT BRAKEPINK - VEHICLE SPEED

BROWN (NOT CONNECTED)

WIRING DIAGRAM

DATACABLE

AUDIOCABLE

CONNECT TOAFTERMARKET RADIO

SCREEN HARNESS ABOVE RADIOSTEP 3

SEE RADIOWIRE REFERENCECHART FORRADIO WIRECOLORS

Page 102: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR02-DS maestro.idatalink.com

Ford transit with 4.3" screen 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Page 103: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

Page 104: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2014Ford EconolinE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 105: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford EconolinE 2008-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 106: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford EconolinE 2008-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 107: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford EconolinE 2008-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER DASH, UNDER THE RADIO

Page 108: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford EconolinE 2008-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 109: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford EconolinE 2008-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 110: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2010Ford EdgE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 111: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford EdgE 2007-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 112: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford EdgE 2007-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 113: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford EdgE 2007-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 114: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford EdgE 2007-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 115: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford EdgE 2007-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 116: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2012Ford EscapE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 117: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford EscapE 2008-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 118: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford EscapE 2008-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 119: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford EscapE 2008-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGEJUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT

Page 120: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford EscapE 2008-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 121: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford EscapE 2008-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 122: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2014Ford ExpEdition

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 123: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford ExpEdition 2007-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 124: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford ExpEdition 2007-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 125: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford ExpEdition 2007-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 126: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford ExpEdition 2007-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 127: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford ExpEdition 2007-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 128: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2010Ford ExplorEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 129: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford ExplorEr 2006-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 130: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford ExplorEr 2006-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 131: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford ExplorEr 2006-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : WHITE/BROWNCENTER CONSOLE, HARNESS GOING TO THE BACK

Page 132: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford ExplorEr 2006-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 133: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford ExplorEr 2006-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 134: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2010Ford ExplorEr sport trac

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 135: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford ExplorEr sport trac 2006-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 136: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford ExplorEr sport trac 2006-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 137: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford ExplorEr sport trac 2006-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : WHITE/BROWNCENTER CONSOLE, HARNESS GOING TO THE BACK

Page 138: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford ExplorEr sport trac 2006-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 139: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford ExplorEr sport trac 2006-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 140: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2010Ford F-sEriEs supEr duty

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 141: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F-sEriEs supEr duty 2008-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 142: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F-sEriEs supEr duty 2008-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 143: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F-sEriEs supEr duty 2008-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGEPASSENGER SIDE, NEXT TO GLOVE BOX

Page 144: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F-sEriEs supEr duty 2008-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 145: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F-sEriEs supEr duty 2008-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 146: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2011-2016Ford F-sEriEs supEr duty

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 147: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F-sEriEs supEr duty 2011-2016

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 148: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F-sEriEs supEr duty 2011-2016

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

Page 149: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F-sEriEs supEr duty 2011-2016

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

Page 150: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F-sEriEs supEr duty 2011-2016

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 151: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F-sEriEs supEr duty 2011-2016

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 152: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2009-2010Ford F150

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 153: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F150 2009-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 154: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F150 2009-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 155: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F150 2009-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER DASH, UNDER THE TRAY

Page 156: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F150 2009-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 157: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F150 2009-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 158: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2011-2014Ford F150

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 159: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford F150 2011-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 160: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford F150 2011-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

Page 161: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford F150 2011-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

Page 162: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford F150 2011-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 163: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford F150 2011-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 164: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2007Ford FivE hundrEd

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 165: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford FivE hundrEd 2006-2007

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 166: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford FivE hundrEd 2006-2007

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

Page 167: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford FivE hundrEd 2006-2007

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

Page 168: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford FivE hundrEd 2006-2007

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 169: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford FivE hundrEd 2006-2007

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 170: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2009-2012Ford FlEx

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 171: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford FlEx 2009-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 172: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford FlEx 2009-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 173: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford FlEx 2009-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, JUNCTION CONNECTOR, IN FRONT OF THE SHIFTER

Page 174: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford FlEx 2009-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 175: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford FlEx 2009-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 176: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2011Ford Focus

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 177: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Focus 2008-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 178: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Focus 2008-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 179: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Focus 2008-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, HORIZONTAL HARNESS ON THE HEATER BOX

Page 180: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Focus 2008-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 181: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Focus 2008-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 182: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2012Ford Fusion

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 183: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Fusion 2006-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 184: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Fusion 2006-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 185: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Fusion 2006-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, IN FRONT OF THE ARM REST

Page 186: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Fusion 2006-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 187: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Fusion 2006-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 188: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2012Ford Mustang

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 189: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang 2007-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 190: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang 2007-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 191: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang 2007-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

Page 192: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang 2007-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 193: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang 2007-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 194: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2013-2014Ford Mustang

BasE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 195: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang BasE 2013-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 196: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang BasE 2013-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 197: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang BasE 2013-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

Page 198: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang BasE 2013-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 199: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang BasE 2013-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 200: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2013-2014Ford Mustang

shakEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 201: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang shakEr 2013-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 202: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang shakEr 2013-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

2

Page 203: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang shakEr 2013-2014

AUX INAUX IN

2

SUB INCENTER IN

SUB INCENTER IN

AUDIOCABLE

OBDII CONNECTORSTEP 4

MAESTRO RR MODULE

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

CONNECT TOAFTERMARKET RADIO

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

FO1 T-HARNESS

WIRING DIAGRAMSTEP 1

STEP 2

STEP 3

STEP 5

STEP 6

WHITEWHITE/BLACKGRAYGRAY/BLACKGREENGREEN/BLACK

PURPLE/BLACKPURPLE

LF RCA INPUT

RF RCA INPUT

LR RCA INPUT

RR RCA INPUT

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

WIRES FROMVEHICLE

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO:ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

Page 204: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang shakEr 2013-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 205: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang shakEr 2013-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 206: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2013-2014Ford Mustang

shakEr pro

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 207: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford Mustang shakEr pro 2013-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 208: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford Mustang shakEr pro 2013-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

2

Page 209: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford Mustang shakEr pro 2013-2014

AUX INAUX IN

2

SUB INCENTER IN

SUB INCENTER IN

AUDIOCABLE

OBDII CONNECTORSTEP 4

MAESTRO RR MODULE

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

CONNECT TOAFTERMARKET RADIO

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

FO1 T-HARNESS

WIRING DIAGRAMSTEP 1

STEP 2

STEP 3

STEP 5

STEP 6

WHITEWHITE/BLACKGRAYGRAY/BLACKGREENGREEN/BLACK

PURPLE/BLACKPURPLE

LF RCA INPUT

RF RCA INPUT

LR RCA INPUT

RR RCA INPUT

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

WIRES FROMVEHICLE

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO:ENSURE THAT NOTHING

IS PLUGGED IN W/R PORT.

SWI 2 : BLUE/ORANGE OR BLUESYNC UNIT, BEHIND THE GLOVE BOX

Page 210: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford Mustang shakEr pro 2013-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 211: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford Mustang shakEr pro 2013-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 212: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2009Ford taurus

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 213: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford taurus 2008-2009

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 214: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford taurus 2008-2009

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 215: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford taurus 2008-2009

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : GRAY/BLUECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 216: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford taurus 2008-2009

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 217: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford taurus 2008-2009

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 218: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2010-2012Ford taurus

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 219: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford taurus 2010-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 220: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford taurus 2010-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 221: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford taurus 2010-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 222: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford taurus 2010-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 223: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford taurus 2010-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 224: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2012Ford taurus x

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 225: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

Ford taurus x 2008-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 226: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

Ford taurus x 2008-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 227: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

Ford taurus x 2008-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 228: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

Ford taurus x 2008-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 229: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

Ford taurus x 2008-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 230: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2009-2012lincoln Mks

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 231: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln Mks 2009-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 232: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln Mks 2009-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 233: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln Mks 2009-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 234: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln Mks 2009-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 235: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln Mks 2009-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 236: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2010-2012lincoln Mkt

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 237: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln Mkt 2010-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 238: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln Mkt 2010-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 239: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln Mkt 2010-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 240: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln Mkt 2010-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 241: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln Mkt 2010-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 242: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2010lincoln Mkx

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 243: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln Mkx 2007-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 244: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln Mkx 2007-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 245: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln Mkx 2007-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 246: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln Mkx 2007-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 247: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln Mkx 2007-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 248: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2012lincoln MkZ

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 249: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln MkZ 2007-2012

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 250: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln MkZ 2007-2012

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 251: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln MkZ 2007-2012

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 252: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln MkZ 2007-2012

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 253: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln MkZ 2007-2012

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 254: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2007-2014lincoln navigator

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 255: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln navigator 2007-2014

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 256: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln navigator 2007-2014

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 257: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln navigator 2007-2014

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGESYNC UNIT, CENTER CONSOLE

Page 258: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln navigator 2007-2014

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 259: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln navigator 2007-2014

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 260: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006lincoln ZEphyr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 261: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

lincoln ZEphyr 2006

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 262: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

lincoln ZEphyr 2006

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

Page 263: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

lincoln ZEphyr 2006

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

Page 264: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

lincoln ZEphyr 2006

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 265: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

lincoln ZEphyr 2006

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 266: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2011MaZda triButE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 267: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MaZda triButE 2008-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 268: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MaZda triButE 2008-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

Page 269: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MaZda triButE 2008-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

Page 270: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MaZda triButE 2008-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 271: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MaZda triButE 2008-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 272: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2011MErcury MarinEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 273: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury MarinEr 2008-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 274: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury MarinEr 2008-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 275: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury MarinEr 2008-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGEJUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT

Page 276: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury MarinEr 2008-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 277: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury MarinEr 2008-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 278: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2011MErcury Milan

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 279: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury Milan 2006-2011

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 280: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury Milan 2006-2011

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 281: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury Milan 2006-2011

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : BLUE/ORANGECENTER CONSOLE, RIGHT SIDE, IN FRONT OF ARM REST

Page 282: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury Milan 2006-2011

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 283: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury Milan 2006-2011

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 284: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2005-2007MErcury MontEgo

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 285: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury MontEgo 2005-2007

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 286: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury MontEgo 2005-2007

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

• Remove the factory radio.

STEP 2• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3• Plug the OBDII connector into the OBDII of the vehicle.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 5• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

3

Page 287: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury MontEgo 2005-2007

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

3

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

OBDII CONNECTOR

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESSSTEP 2

STEP 5

WIRES FROMVEHICLE

STEP 3

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

PINK/RED (NC)

AUDIOCABLE

Page 288: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury MontEgo 2005-2007

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 289: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury MontEgo 2005-2007

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 290: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2006-2010MErcury MountainEEr

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 291: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury MountainEEr 2006-2010

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 292: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury MountainEEr 2006-2010

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 293: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury MountainEEr 2006-2010

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : WHITE/BROWNCENTER CONSOLE, HARNESS GOING TO THE BACK

Page 294: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury MountainEEr 2006-2010

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 295: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury MountainEEr 2006-2010

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

Page 296: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

E L E C T R O N I C S

Click here for: Radar Installation Guides

2008-2009MErcury saBlE

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

PRODUCTS REQUIREDiDatalink Maestro RR or RR2 Radio Replacement InterfaceiDatalink Maestro FO1 Installation Harness

PROGRAMMED FIRMWAREADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCESMaestro RR2 Programmable Outputs Guide

OR

OPTIONAL ACCESSORIES

Page 297: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 2

MErcury saBlE 2008-2009

WELCOME

NEED HELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Troubleshooting Table 6

1 866 427-2999

maestro.idatalink.com/supportwww.12voltdata.com/forum

[email protected]

Page 298: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 3

MErcury saBlE 2008-2009

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Connect every wire to the aftermarket radio main harness and match the wire colors.

• Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram)

STEP 2Vehicles equipped with navigation radios skip to Step 3.

(Required for vehicles equipped with SYNC, without factory navigation system; refer to Vehicle Wire Chart)

• Disassemble the dashboard carefully and remove the factory radio from its housing without disconnecting it.

• See the WIRE CHART for vehicle wire color and location.

• Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test probe to the wire SWI 2 wire. Have the ignition and the radio ON. If the SWI 2 wire is connected, the multimeter will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button.

• Cut the SWI 2 INPUT wire.

• Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3• Connect the factory harness to the FO1 T-harness. Connect

only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Plug the Data cable to the data port of the aftermarket radio.

• Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).

Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.

• Insert the RCA connectors into the aftermarket radio.

NOTES:

The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory amplifier.

The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable).

The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

STEP 6• Secure the aftermarket radio in the dashboardhousing.

• Connect all the harnesses to the Maestro RR module then test your installation.

1

Page 299: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 4

MErcury saBlE 2008-2009

AUX INAUX IN

SUB INCENTER IN

SUB INCENTER IN

1

OBDII CONNECTORSTEP 4

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

BROWN (NOT CONNECTED)YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

DATACABLE

PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

RCA CABLES

WIRING DIAGRAMSTEP 1 STEP 5

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

SEE RADIO WIREREFERENCECHARTFOR RADIO WIRECOLORS

MAESTRO RR MODULE

DATACABLE

FACTORY RADIO HARNESS

SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATEWIRE

SYNCMODULE SIDE

STEERINGWHEEL SIDE

STEP 2

STEP 3

STEP 6

WIRES FROMVEHICLE

FO1 T-HARNESS

STEERING WHEELCONTROL CABLE

NOT REQUIRED

PIONEER RADIO: ENSURE THAT NOTHINGIS PLUGGED IN W/R PORT.

CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

AUDIOCABLE

SWI 2 : GRAY/BLUECENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK

Page 300: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 5

MErcury saBlE 2008-2009

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-HarnessWire Color on Alpine

cableWire Color on Kenwood

cableWire Color on Pioneer

cableWire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

Page 301: HOW TO USE THIS INSTALL GUIDE - Custom Sounds€¦ · INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on

ADS-RR(SR)-FOR01-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2019 6

MErcury saBlE 2008-2009

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR.

There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the OEM radio.

The data lines are not present behind the radio and must be connected at the OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to:BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the fl ash. Verify the radio’s serial number entered during the fl ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds).Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: [email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.