Post on 29-Dec-2015
Chapter 2Chapter 2 A Loop in the Pattern A Loop in the Pattern
Designing the Main Loop and Timing
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
ChecklistChecklistThe following tools will be used throughout the course: MPLAB X, Integrated Development Environment (v1.8 or later,
free) MPLAB XC16, C compiler (v1.11 or later, free)
The following pieces of documentation will be used during this lesson:
PIC24FJ128GA010 Datasheet –DS39747 (latest rev.) PIC24 Family Reference Manual - Section 14. Timers
Make sure they are available and/or installed and ready to use on your computer.
You can download them from Microchip web site at: http://www.microchip.com/mplabx
And http://www.microchip.com/xc16
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
A New ProjectA New Project Use the New Project wizard to create a new project
Call it: “2-ALoopInThePattern” Use the New File wizard to create a new source file
Call it: Loop.c
/* * File: Loop.c * Author: your name here * * Created current date here */
#include <xc.h>
int main( void) { return 0;}
But you can also use the form:void main( void){ // no return required}
Or simply:main(){}
But you can also use the form:void main( void){ // no return required}
Or simply:main(){}
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
““while” Loopswhile” Loops In C there are several ways to design a loop. The first we are going
to explore is the “while” loop:
while ( x){ // your code here…}
Where ( X) is a logical expression false is represented as the integer zero true is represented by any integer except zero
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Logical OperatorsLogical Operators || the logic OR operator, && the logic AND operator, ! the logic NOT operator These operators consider their operands as
logical (Boolean) values using the rule mentioned above, and they return a logical value.
Here are some trivial examples, assuming: a = 17 b = 1
( a || b) is true, ( a && b) is true ( !a) is false
In other words, they are both “true”In other words, they are both “true”
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Comparison OperatorsComparison Operators There are, then, a number of operators that compare numbers
(integers of any kind and floating point values, too) and return logic values.
They are: == the equal-to operator, != the NOT-equal to operator. > the greater-than operator. >= the greater-or-equal to operator. < the less-than operator. <= the less-or-equal to operator.
Here are some examples, assuming: a = 10
( a > 1) is true (-a >= 0) is false ( a == 17) is false ( a != 3) is true
Composed of two equal signs to distinguish it from the assignment operator ‘=‘ we used in the previous lesson.
Composed of two equal signs to distinguish it from the assignment operator ‘=‘ we used in the previous lesson.
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Curious CasesCurious Caseswhile ( 0){ // your code here…}
while ( 1) { // your code here…}
Will never execute this code!Will never execute this code!
Will execute this code for ever!Will execute this code for ever!
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Writing a Main LoopWriting a Main Loop It is time to add a few new lines of code to the
‘loop.c’ source file and put the while loop to good use.
main(){ // init control registers TRISA = 0xff00; // all PORTA as output // main application loop while( 1) { PORTA = 0xff; PORTA = 0; } // main loop } // main
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Not so fast, please!Not so fast, please! Run > Run Program from the main menu.
MPLAB X will now recompile the program for immediate execution. It will be downloaded into the PIC24 flash memory and execution will start immediately
NOTE: When in run mode, there is no animated icon and MPLAB X seems inactive, but the target PIC24 is alive and executing continuously the application at full speed
Warning: You will not be able to see any flashing of the LED bar! This is due to a limitation of our human eyes. The PIC24 is actually turning the LEDs on and off but, assuming
our default configuration of the main oscillator (32MHz), this is happening at the rate of several million times per second!
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Using a TimerUsing a Timer Timer1 Block Diagram:
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Configuring Timer1: T1CONConfiguring Timer1: T1CON
Use the following basic configuration: Activate Timer1: TON = 1 Use the MCU clock as the source (Fosc/2): TCS = 0 Set the prescaler to the maximum value (1:256): TCKPS = 11 The input gating and synchronization functions are not required, since we use the
MCU internal clock directly as the timer clock: TGATE = 0, TSYNC = 0 Do not worry about the behavior in IDLE mode, for now: TSIDL = 0 (default)
Once we assemble all the bits into a single 16-bit binary value, we get: T1CON = 0b1000000000110000;
Or in a more compact hexadecimal notation: T1CON = 0x8030;
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
A Timed LoopA Timed Loop#include <config.h>#define DELAY 16000 main(){ // init control registers TRISA = 0xff00; // all PORTA as output T1CON = 0x8030; // TMR1 on, prescale 1:256 Tclk/2 // main application loop while( 1) { //1. turn pin 0-7 on and wait for 1/4 of a second PORTA = 0xff; TMR1 = 0; while ( TMR1 < DELAY) { } // 2. turn all pin off and wait for a 1/4 of a second PORTA = 0; TMR1 = 0; while ( TMR1 < DELAY) { } } // main loop } // main
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Notes for Assembly ExpertsNotes for Assembly Experts Logic vs. Binary operators in C:
Binary logic operators take pairs of bits from each operand and compute the result according to the defined table of truth.
Logic operators, look at each operand (independently of the number of bits used) as a single Boolean value.
Example on byte sized operands: 11110101 11110101 (true)binary OR 00001000 logical OR 00001000 (true) -------- --------gives 11111101 gives 00000001 (true)
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Notes for PICmicro ExpertsNotes for PICmicro Experts Difference between 8-bit PICmicros and the PIC24:
There is no Timer0 All timers are 16-bit wide. Each timer has a 16-bit period registers (PR). A new 32-bit mode timer-pairing mechanism is
available for Timer2/3 and Timer4/5. A new external clock gating feature has been added
on Timer1.
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Tips and TricksTips and Tricks When designing applications that have to
operate reliably on large time scales (months, years… ), consider providing a periodic refresh of the most important control registers of the essential peripherals used by the application. Group the sequence of initialization instructions in one or
more functions. Call the functions once at power up, before entering the
main loop, but also make sure that inside the main loop the initialization functions are called when no other critical task is pending and every control register is re-initialized periodically.
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Suggested ExcercisesSuggested Excercises Output a counter on the PortA pins instead of the
alternating on and off patterns. Use a rotating pattern instead of alternating on and
off
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Recommended ReadingsRecommended Readings Ullman, L. & Liyanage, M. (2005), C Programming, Peachpit
Press, Berkeley, CA.
Adams, N. (2003), The flyers, in search of Wilbur and Orville Wright, Three Rivers Press, New York, NY
Di Jasio – Programming 16-bit Microcontrollers in C (Second Edition)
Online ResourcesOnline Resources http://en.wikipedia.org/wiki/Control_flow#Loops A wide perspective on programming languages and
the problems related to coding and taming loops.