Multi Configuration Composite Body Bridge / Frac Plugs
unique combination of composites to provide a dependable, durable, and cost-efficient method for temporary zone isolation during stage fracs in both vertical and horizontal wells. The Express Series Plugs are constructed primarily from composite with cast iron slips ensuring fast drill times while remaining reliable.
The Express Series Plug is a multi-configuration plug allowing for a user to easily convert the tool from a Ball Drop to a Caged Ball or Bridge Plug. This conver-sion is easily obtained using two simple kits (Bridging Pin / Caged Ball Assembly). Express Series Plugs can be run with any wireline setting tool or tubing run hydraulic setting tool. Cast iron slips are hardened to wicker depth only and can be set in up to P110 casing.
is converted using a simple composite “Bridging Pin” that is threaded into the mandrel while sealing in the Inner Diameter. This plugged ID is drilled out before the top slip, thus allowing the upper and lower zones to equalize during drill out.
Express Series Ball Drop Frac: After the Ball Drop Frac Plug is set, the inner diameter remains open thus allowing wireline operators to continue work above. A ball is then dropped from the surface and pumped down until it seats on the tool. Once the ball is seated, the operator can pressure up against the Frac Plug.
Express Series Caged Ball Frac Plug: Similar to the Ball Drop Frac Plugs, although the Caged Ball Frac Plug houses the ball in the upper ID. This conversion is done using a simple composite Ball Caged adapter. When zonal pressure is greater from below the plug, the ball cage allows the lower and upper zones to comingle. When zonal pressure is greater from above, the ball seats thus isolating the zones.
Available in 4 ½” and 5 ½”. (other sizes pending)
Sets securely in up to P110 Grade Casing.
Compact and easy running.
Patent Pending
Consistent Drill Times of 13-20 minutes or less.
Utilizes unique “Lug” design on the top and muleshoe bottom ensuring that the plugs do not spin during drill out. Lug shoe also available.
Plugs are set using a universal setting sleeve and shear sleeve adapter.
Can be drilled using conventional tubing or coiled tubing.
Materials used in construction conducive to a wide range of environments.
Slips are only hardened to wicker depth for ease of drill out.
Pump Down Wiper available upon request.Bridge Ball Drop Caged Ball
The Express Series Bridge and Frac Plugs utilize a Express Series Bridge: The Express Series Bridge Plug
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Casing O.D. Part Number Overall
LengthCasing
Wt.MinI.D.
MaxI.D.
ToolO.D.
Operating Range Setting Tool
5 ” ECFP-5500-000 21.50” 13-23# 4.580 5.044 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-001 24.00” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-002 24.00” 13-23# 4.580 5.044 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECBP-5500-000 21.50” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECBP-5500-001 24.00” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECBP-5500-002 24.00” 13-23# 4.580 5.044 4.425 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-000CB 21.750” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-001CB 24.250” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-002CB 24.250” 13-23# 4.580 5.044 4.425 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO
Bridge
6k 8k 10k
Ball Drop Caged Ball
Pump Down Rubber
ECFP-4500-002 22.68” 9.5-15.1# 3.826 4.09 10K, 300 Deg Baker #10 / 3 ½" G.O.
ECFP-4500-001 22.68” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.
ECFP-4500-000 19.125” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.
ECBP-4500-002
ECBP-4500-001
ECBP-4500-000
22.68” 9.5-15.1# 3.826 4.09 10K, 300 Deg Baker #10 / 3 ½" G.O.
22.68” 9.5-15.1# 3.826 4.09 8K, 275 Deg Baker #10 / 3 ½" G.O.
19.125” 9.5-15.1# 3.826 4.09 6K, 250 Deg Baker #10 / 3 ½" G.O.
ECFP-4500-002CB 23.40” 9.5-15.1# 3.826 4.09 10K, 300 Deg Baker #10 / 3 ½" G.O.
ECFP-4500-001CB 23.40” 9.5-15.1# 3.826 4.09 8K, 275 Deg Baker #10 / 3 ½" G.O.
ECFP-4500-000CB 19.375” 9.5-15.1# 3.826 4.09 6K, 250 Deg Baker #10 / 3 ½" G.O.
4.425
4.425
3.609
3.609
3.609
3.609
3.609
3.609
3.609
4 ”
4 ”
4 ”
4 ”
4 ”
4 ”
4 ”
4 ”
4 ”
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Ball Drop Frac Plug Configuration
After the Ball Drop Frac Plug is set, the inner
diameter remains open thus allowing wireline
operators to continue work above. A ball is then
dropped from the surface and pumped down until
it seats on the tool. Once the ball is seated, the
operator can pressure up against the Frac Plug.
The Shear Sleeve Adapter used to set the plugs is
designed so that the user can, if needed, run the
Drop Ball “in place” inside the Adapter. This gives
the user to choice to utilize the plug as a Flow
Back Plug without having to drop the ball
from the surface.
Casing O.D. Part Number Overall
LengthCasing
Wt.MinI.D.
MaxI.D.
ToolO.D.
Operating Range Setting Tool
4 ” ECFP-4500-002
4 ” ECFP-4500-001
4 ” ECFP-4500-000
5 ” ECFP-5500-000 21.50” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-001 24.00” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-002 24.00” 13-23# 4.580 5.044 4.425 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO
Accessory Part Number
2” Composite Drop Ball for 5 ½" ECFP-5500-031
1 11/16" Composite Drop Ball for 4 ½" ECFP-4500-031
5 ” Pump Down Rubber 001758422555891
22.68” 9.5-15.1# 3.826 4.09 3.609 10K, 300 Deg Baker #10 / 3 ½" G.O.
22.68” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.
19.125” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.
Ball Drop
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Bridge Plug Configuration
The Express Series Bridge Plug is converted using
a simple composite “Bridging Pin” that is
threaded into the mandrel while sealing in the
Inner Diameter. This plugged ID is drilled out
before the top slip, thus allowing the upper and
lower zones to equalize during drill out.
Casing O.D. Part Number Overall
LengthCasing
Wt.MinI.D.
MaxI.D.
ToolO.D.
Operating Range Setting Tool
4 ” ECBP-4500-002
5 ” ECBP-5500-000 21.50” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO
22.68” 9.5-15.1# 3.826 4.09 3.609 10K, 300 Deg Baker #10 / 3 ½" G.O.
4 ” ECBP-4500-001 22.68” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.
4 ” ECBP-4500-000 19.125” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.
5 ” ECBP-5500-001 24.00” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECBP-5500-002 24.00” 13-23# 4.580 5.044 4.425 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO
Accessory Part Number
5 1/2" Composite Bridging Pin ECBP-5500-060
4 1/2" Composite Bridging Pin ECBP-4500-060
5 1/2" Pump Down Wiper 001758422555891
Bridge
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Caged Ball Frac Plug Configuration
The Express Series Caged Ball Frac utilizes a
simple Ball / Cage Adapter that houses a ¾”
Brass Ball in the upper ID of the plug. When
zonal pressure is greater from below the plug,
the ball cage allows the lower and upper
zones to comingle. When zonal pressure is
greater from above, the ball seats thus
isolating the zones.
Casing O.D. Part Number Overall
LengthCasing
Wt.MinI.D.
MaxI.D.
ToolO.D.
Operating Range Setting Tool
4 ” ECFP-4500-002CB
5 ” ECFP-5500-000CB 21.50” 13-23# 4.580 5.044 4.425 6K, 250 Deg Baker #10 / Baker #20 / 3 ” GO
23.40” 9.5-15.1# 3.826 4.09 3.609 10K, 300 Deg Baker #10 / 3 ½" G.O.
4 ” ECFP-4500-001CB 23.40” 9.5-15.1# 3.826 4.09 3.609 8K, 275 Deg Baker #10 / 3 ½" G.O.
4 ” ECFP-4500-000CB 19.375” 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O.
5 ” ECFP-5500-001CB 24.00” 13-23# 4.580 5.044 4.425 8K, 275 Deg Baker #10 / Baker #20 / 3 ” GO
5 ” ECFP-5500-002CB 24.00” 13-23# 4.580 5.044 4.425 10K, 300 Deg Baker #10 / Baker #20 / 3 ” GO
Accessory Part Number
5 1/2" Composite Caged Ball Assembly ECFP-5500-108
4 1/2" Composite Caged Ball Assembly ECFP-4500-108
5 1/2" Pump Down Wiper 001758422555891
Caged Ball
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Setting Equipment
Express Series Plugs are set using a universal
Setting Sleeve and Setting Sleeve Adapter. Setting
kits are designed to be run on any wireline setting
tool or tubing run hydraulic setting tool with either
Baker #10, Baker #20 or 3 ½” G.O. connections.
The Shear Sleeve Adapter is placed around the top
of the plug and secured using seven steel shear
screws while the Setting Sleeve is installed around
the Shear Adapter and down to the top slip.
The Setting Assembly utilizes an Adjuster Nut that
mates the directly to the setting tool. The setting
sleeve is allowed to be threaded upwards past the
Adjuster Nut and secured onto the setting tool.
This allows the user to change out plugs on the
Sheer Sleeve Adapter without having to remove
the setting sleeve.
Part Number Description Overall Length Weld I.D.
EWST-BK10-203 Shear Sleeve Adapter – 5 ” on Baker #10 9.00” E5-1
EWST-BK20-ASM Setting Sleeve – 5 ” on Baker #20 22 7/16” E5-2
EWST-BK20-202 Shear Sleeve Adapter – 5 ” on Baker #20 9.00” E5-2
EWST-3625-ASM Setting Sleeve – 5 ” on 3 ” G.O. 22 7/16” E5-G
EWST-3625-180 Shear Sleeve Adapter – 5 ” on 3 ” G.O. 16.50” E5-G
ECFP-5500-028 Shear Screws for Shear Sleeve Adapter 9/16” N/A
Setting Sleeve Sleeve Adapter
EWST-BK10-ASM ” on Baker #10Setting Sleeve Assembly - 5 22 7/16” E5-1
EWST-3625-180-45 Setting Sleeve Adapter, 4 ½” on 3 ½” G.O E4-G
EWST-3625-ASM-45 Setting Sleeve, 4 ½” on 3 ½” G.O E4-G
EWST-BK10-180 Setting Sleeve Adapter, 4 ½” on Baker #10 9.73” E4-1
EWST-BK10-ASM-45 Setting Sleeve, 4 ½” on Baker #10 18.25” E4-1
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Composite Mutli-Configuration Plugs
Snug the tension sleeve correctly. Do not over tighten.
Be sure that nut is tightened correctly.
Do not allow the weight of the string to set on the
shoe of the plug when setting into well head.
Guide the plug through lubricator and rams before
setting lubricator in place. If the well has pressure on
it, be sure to raise tools to the top of the lubricator
before opening well head to pressure.
Running speed should be limited to 150 feet per
minute. Be extremely careful going into liner tops.
If you experience a misfire, do not pull out of hole any
faster than 150 feet per minute.
Never set plugs in casing collars.
Always set plugs in static well conditions.
Never perforate any closer than 50 feet to a plug.
Use bit and scraper in casing to remove any cement and scale from casing wall before you run any equipment that grips the casing.
Before running any plugs in hole, a junk basket and gage ring should be run for the appropriate size casing.
Choose correct size plug for casing. Composite Plugs usually cover the complete casing weight range.
Install the plug on the setting tool correctly. Do not over tighten.
Use correct setting tool size for the plug that you are running. Baker 10 or Go Compact for the 4 ½” and Baker #10, Baker #20 or Go Compact for the 5 ½” or larger.
All setting tools should be thoroughly redressed before each run.
Be sure that all oil levels are correct for the setting tool/temperature you are running.
Use the lock spring on all tools designed for use with a lock spring.
Express Series
Trident Frac Plugs by Poseidon 800-321-3780
Contact InformationPoseidon Rentals, LLC
17214 Saddlehorn
New Caney, TX 77357
800-321-3780
Account Management
D. Wade Maxwell Christina Maxwell
832-693-2966 281-785-7738
Top Related