DIY Thermaxx GownHow-to guide
Tips
Please share photos of your work or satisfied recipients with us at
[email protected] or on our Thermaxx Facebook or LinkedIn
pages
• Read through all of the instructions first!
• Save an unsewn cutout so that you can
trace it onto several in a row to work faster
• You can save material by rotating every
other pattern as pictured on the right
• If using a knife or table, you can cut
multiple layers at once but make sure to
tape or clamp corners well because the
material is slippery.
Supplies
• Minimum 4’ x 6’ flat
space
1. Clean work surface area
2. Tyvek HomeWrap
• 4 ½’ x 100’ roll
• Home Depot can cut a 9’
Roll into two 4.5’- Call first
3. Scissors or Utility Knife
4. Sharpie marker or similar
5. Tape measure or ruler
6. Office Stapler or Sewing Machine
7. Staples or Thread
8. Sponge or Towel
9. Spray bottle (alcohol or bleach)
10. Printer
*“TYVEK” AND “HOMEWRAP” ARE REGISTERED TRADEMARKS OF DUPONT, THEIR USE DOES NOT IMPLY ANY AFFILIATION OR ENDORSEMENT BY THEM
Step 1Get organized
Wash your hands Clean your work surface Gather your supplies
Step 2
4 ½’ x 6’
Unroll a 6’ section of
HomeWrap
You will need 54”x70”
for the regular size
pattern
Unroll Material
Step 3
Using tape measure
or ruler, draw the
pattern provided on
following page onto
the Tyvek
Note(s):
• Pattern is scaled with 1 inch
squares and measurements
starting from bottom-left
Trace pattern
Step 4
Cut pattern outline
with scissors
Cut pattern
1 square = 1 inch
545352515049484746454443424140393837363534333231302928272625242322212019181716151413121110987654321
70696867666564636261605958575655545352515049484746454443424140393837363534333231302928272625242322212019181716151413121110987654321
70696867666564636261605958575655545352515049484746454443424140393837363534333231302928272625242322212019181716151413121110987654321
545352515049484746454443424140393837363534333231302928272625242322212019181716151413121110987654321
Inches
Step 5
Cut along inside
edge of straps and
cut out thumb
holes
Note(s):
• Strap width is 1”
• Thumb holes are ovals 3”
wide by 2” tall
Cut straps and thumb holes
Step 5.1
This is what the
completed cutout
will look like
Note(s):
• To save time – set this one
aside and use it to trace
several more outlines, cut
those out, and then sew them!
Pause to admire your handywork
Step 6Fold Sleeves over along centerline at 7”
(Per Graphic: Red edges to each other,
green edges to each other)
7”
7”
Step 7Fold top edge of sleeve over
again by 0.5” and staple or
sew where indicated with blue
dotted lines
Note(s):
• Staples or thread should be about 1/8” in from
outside edges
• Smooth/solid side of staples should face front of
gown
Step 8Clean thoroughly with bleach
*could be substituted with alcohol if needed
Step 9Print and Include Product
Information on next page
Feel free to personalize your own but please make sure
that the following language is included:
These gowns are constructed with HomeWrap, a material that has not
been evaluated for protection against bloodborne pathogens but does
have fluid and particle protection properties similar to that of Tyvek 400
and superior to clothing and patient gowns suggested by the CDC and
FDA per crisis capacity strategy recommendations.
For use only when FDA cleared gowns or apparel are not
available. Not recommended for use in a surgical setting or where
significant exposure to liquid bodily or other hazardous fluids may be
expected, or in any clinical setting where the infection risk level is high.
14 Farwell St. Bldg 2B, West Haven, CT 06516 (203) 672-1021 [email protected] thermaxxjackets.com
PRODUCT INFORMATION
COPYRIGHT THERMAXX JACKETS, 2020
The Thermaxx gown is designed to protect from contact with liquids and particles while alsoproviding an additional puncture/tear resistant shield for delicate PPE and clothing wornunderneath. The gown consists of a full torso covering with integrated sleeves manufactured usingTyvek HomeWrap, a spun high density polyethylene material. HomeWrap material is readilyavailable, allowing Thermaxx to transition from insulation production to immediately supplyingprotective gear for those in need per CDC Crisis Capacity Strategy recommendations.
Protection for EMS & First Responders
✓ Made from Tyvek HomeWrap*✓ Resists fluid and air penetration✓ Difficult to tear✓ Designed to easily don/doff safely
Thermaxx Disposable Gown
PRODUCT INFORMATION – THERMAXX DISPOSABLE GOWN
* “TYVEK” AND “HOMEWRAP” ARE REGISTERED TRADEMARKS OF DUPONT, THEIR USE DOES NOT IMPLY ANY AFFILIATION OR ENDORSEMENT BY THEM
Material Properties:• Barrier for particles down to 2 microns in size
(vs. 1 micron for Tyvek 400, 0.3 for N95 masks)• Basis Weight: 1.8 oz/yd2 (vs. 1.2 for Tyvek 400) • AATCC127 Water Penetration Resistance: 98 in.
(vs. 45 in. for Tyvek 400)• Thickness: 5.5 mil (vs. 5.9 for Tyvek 400)
The Thermaxx gown is constructed with HomeWrap, amaterial that has not been evaluated for protectionagainst bloodborne pathogens but does have fluid andparticle protection properties similar to that of Tyvek 400and superior to clothing and patient gowns suggested bythe CDC and FDA.
For use only when FDA cleared gowns or apparel are notavailable. Not recommended for use in a surgicalsetting or where significant exposure to liquid bodily orother hazardous fluids may be expected, or in anyclinical setting where the infection risk level is high.
Step 10Deliver to those in need!
Hospitals
Clinics
First responders
Fill up a box, seal, and write “non-surgical gowns” on the outside. Contact your local fire department to coordinate delivery.
Top Related