Download - TEMCO · T3 Series Bacnet Programmable Controller The T3000 controller is a multi-user, including T3-BB, T3-LB and T3-TB, which can stand alone DDC panel

T3 Series Bacnet Programmable Controller

The T3000 controller is a multi-user, including T3-BB, T3-LB and T3-TB, which can stand alone DDC panel with full communications capabilities. They can be used either stand alone, or in a multiple network system. Multiple communication ports allow the controller to simultaneously operate on anetwork, host sub networks, and to communicate to local and remote operators.

Setup and programming are done on a PC without the need to be connected to live hardware as it is the case with many systems. When the program is ready for on-site testing, connect to a live panel and download the T3000 software. Programming can be done remotely over the network and modem connections as well. The network system is very fl exible and also more economical for the installation.

CONTROLS.COMTEMCO

T3-BB

10Year

WARRANTY

T3-LB

T3-TB

Specifications

SoftwareInteractive dynamic color graphicsIndustry standard Bacnet & Modbus protocolsUser programming, built in networking features16 Control Basic programs16 User screen displays8 Weekly routines, 4 annual routines128 User variables16 PID controllers8 passwords or users

HardwareHighly Configurable: any combination of input/output cards totalling up to 64 pointsDigital output: 5V/125VAC, 30DVCAnalog output: 0-10VUniversal input: Thermistor, 0-10V, 0-5V, 0-20mAMechanical relays 2A, 24VAC/DCDiagnostic LEDs & Hand-Off-Auto Switches512K Flash / 512k RamSD Disk slot for trend logs, alarms, graphicsEthernet Port: Bacnet & Modbus supported simultaneously2 x RS485 portsUSB Port only for T3-BB, T3-LBRS232 only for T3-BBZigbee port is optional, only for T3-BB, T3-LBClock with battery backup

• Surge-protected Universal Inputs with 12-bit resolution• UL listed ABS enclosure with rubberized texture creates a high end feel. • Software configure the I/O ranges with the free T3000 software or by writing to the registers with your own software. • Each output has a hand-off-auto switch for easy troubleshooting and overrides. • Each I/O as well as the RS485 connections have a separate screw terminal, there’s no need to gang two wires under one terminal for any of the terminations.• High/Low speed input pulse counters• RS485 sub baudrates: 9600, 19200• RS485 main baudrates: 1200~921600• Transportation methods are RS485, Ethernet, USB, Zigbee but it can, at the same time, support Modbus and Bacnet. • Source code for the modules is available with your first purchase. • T3000 front end is free and open source: http://tinyurl.com/hgxavu5• Compiled version of the front end is here: http://tinyurl.com/hgxavu5• Power Supply Voltage: 24V AC/DC• Relay: 5A/125VAC, 30VDC• Operating Temperature: -30~70°C (-22~158°F)• Maximum Power Consumption T3-BB: 10W T3-LB: 10W T3-TB: 6W• Case Color: Black

Part Number Scheme


1) T3-BB(Big Brother) 2) T3-LB(Little Brother) 2) T3-TB(Little Brother)

Network Diagram

Dimensions


Remote

T3-LB

Expansion I/O

Ethernet

Building

Operator

T3000 Building Automation

System Overview

SUBNET2RS485

T3-BB T3-TB T3-8o

RS485

FAN COIL

VAV

VALVES

BTU METERS

TSTAT8

TSTAT6

TSTAT7

TSTAT8

VALVES BOILERS

CHILLERS

User

MAIN NET1RS485

T3-22i

Wiring Diagram


32

USB

999897

12-24VGND

11

0/2

20

VA

C - IN

24

VA

C - O

UTAC/DC

ETHER

NET

2

3

5

969594

9392

TX

RX

GND 33

3534

RS485 SUBNET PORT1

32 UNIVERSAL INPUTS

3 65

2 66THERMOSTATTEMPERATUREFILTER SWITCHOCCUP SENSORFLOW SENSORFAN STATUSWINDOWCHANGEOVERFREEZE PROTECTPOWER METERBTU METERS

32 UNIVERSAL INPUTS

1 67

36

INP

UT

SR

S2

32 R

S48

5R

S48

5LAN

68

79

122

HEAT PUMP

FAN COIL

AIR HANDLER

112 HYDRONICS

12 ANALOG OUPUTSMODULATING VALVES

MODULATING DAMPERS

80 11124VAC

91 10024VAC

12 DIGITAL OUPUTS

RS485 SUBNET PORT2

POW

ER

T3-BB WIRING DIAGRAM

HEAT PUMP

FAN COIL

AIR HANDLER

HYDRONICS

12 DIGITAL OUPUTS

THERMOSTATTEMPERATUREFILTER SWITCHOCCUP SENSORFLOW SENSORFAN STATUSWINDOWCHANGEOVERFREEZE PROTECTPOWER METERBTU METERS

32 UNIVERSAL INPUTS

1 35

342

333

2016

36 63

ETHERN

ET

T3-LB WIRING DIAGRAM

LAN1817

19

MODULATING VALVES

MODULATING DAMPERS

2ANALOG OUTPUTS

24VAC45 54

16 U

I

GND

4950

11

0/2

20

VA

C - IN

24 V

AC

- OU

T

24VAC/DC

41

4748

46

515253

RS485 SUBNET NETWORK

RS485 MAIN NETWORK

58

6 D

O4 A

O

42 57


T3-TB Output Jumper Settings

1 28

27THERMOSTATTEMPERATUREFILTER SWITCHOCCUP SENSORFLOW SENSORFAN STATUSWINDOWCHANGEOVERFREEZE PROTECTPOWER METERBTU METERS

2

263

1811

11INPUTS

151617

29 52

30 51

31 50

4DIGITAL OUTPUTS

ETHE

RNET

T3-TB WIRING DIAGRAM

LAN1314

12

HEAT PUMP

FAN COIL

AIR HANDLER

HYDRONICS

MODULATING VALVES

MODULATING DAMPERS

2ANALOG OUTPUTS

24VAC

AO

G36 45

11 IN

PU

TS

8 OU

TPU

TS

GND

4140

11

0/2

20

VA

C - IN

24

VA

C - O

UT

24VAC/DC

32

34

33 2UNIVERSAL OUTPUTS

35 46

3839

37

424344

RS485 SUBNET NETWORK

RS485 MAIN NETWORK

Highlight

ControllerT3-BB

Big BrotherT3-LB

Little BrotherT3-TB

Tiny BrotherTotal Channels: 56 26 19 Universal Input 32 16 11 Analog Output 12 4 2 Relay Output 12 6 4 Universal Output 2*Comm ports: RS485 2 2 2 RS232 1 0 0 Ethernet 1 1 1 USB 1 1 0 Option port** 1 1 0

These units transportation methods are RS485, Ethernet, USB, Zigbee but it can, at the same time, support Modbus and Bacnet. The T3-BB unit features 32 channels input and 24 channels output including 12 channels analog output and 12 channels digital output. As for the T3-LB, there are 16 channels input and 10 channels output including 4 channels analog output and 6 channels digital out-put. For T3-TB, it includes 11 inputs and 8 outputs which contain 2 analog outputs, 4 digital outputs and 2 universal outputs. All these channels can be controlled directly by the mini panel through the use of input and output cards.

* The 2 universal output can be jumper selected as either 1-10V analog or relay outputs.

** zigbee module.

1.Click to scan Device detected 2.Click to close

T3000 Operation Instructions

1. Download T3000 software http://tinyurl.com/zsjv39y and install it.2. Take an example of T3-BB here, connect T3-BB to PC by RS485 network at pin 94, 95, and 96 or Ethernet. 3. Open T3000 software, and click icon building, an popup window will appear, set protocol to Auto, then close it. Click scan icon which is next to the icon building to find the connected unit.

Then click the device log what have been connected, T3000 software will show the info in righ hand place. You can click Input, Output and other icon.


3.Click to select minipanel

4.Click input to show table right

T3-BB T3-LB T3-TB SpeedLow Speed Input channels 1-32 1-16 1-11 1 HzHigh Speed Input channels 27-32 11-16 3-11 1M Hz

For T3-BB, T3-LB, T3-TB, all the inputs channels have pulse counters. High speed counters capable of 1M Hz. Low speed inputs channels reach to 1 hz per channel.

Here we take an example of T3-BB, showing how to configure the high speed and low speed coun-ters in T3000 software.

4. Click input icon, it will show all inputs in T3000 software.


5.Click input to show table below

Click input to show table below

5. Click output icon, it will show the output view.


*6.Steps to get zigbee information by T3000.

2.Click to see table below

3.Zigbee setting here now

1.Click the device with zigbeeZ

oom

Register List

Address Num Length Description0~3 1 4 Reserved for serial numbler4~5 1 2 firmware Version Number6 1 1 Modbus device address7 1 1 Prodouct model8 1 1 Hardware Version Number9 1 1 PIC rev10 1 1 Temporary address for plug-n-play addressing scheme11 1 1 reserved12 1 1 UART0 Baudrate. 5 - 9600 , 6 - 1920013 1 1 Enable node plug and play14 1 1 ISP Version15 1 1 Reserved16 1 1 Update status 17 1 1 reserved18 1 1 UART1 Baudrate. 5 - 9600 , 6 - 1920019 1 1 UART2 Baudrate.(UART_1200 = 0, UART_2400 = 1, UART_3600 = 2,

UART_4800 = 3, UART_7200 = 4, UART_9600 = 5, UART_19200 = 6, UART_38400 = 7, UART_57600 = 8, UART_115200 = 9, UART_921600 = 10

33 1 1 test cmd, write 77 - reboot, 100 - set default paramer, 111 - erase prg, 150 - clear tstat db

34 1 1 board type, big or small. 1 - big , 2 - samll,3-tiny,4-vav35 1 1 instance number36 1 1 station number39 1 1 EN clear tstat db42 1 1 USB MODE43 1 1 EN DYNDNS ,// 0 - no 1 - disable 2 - enable44 1 1 DYNDNS provider, // 0- www.3322.org 1-www.dyndns.com 2 - www.no-

ip.com 45 1 1 dyndns update timer46 2 1 NETWORK: MSB, MSB-147 2 1 MSTP NETWORK: MSB, MSB-151 1 1 TOP hardware52 1 1 c8051f023 firmware rev53 1 1 sm5964 firmware rev59 1 1 "com0 configure MAIN_MSTP = 0,MAIN_MODBUS

= 1,MAIN_PTP = 2,SUB_GSM = 3,MAIN_ZIG = 4,SUB_ZIG = 5,SUB_MODBUS = 6 "


Address Num Length Description60 1 1 com1 configure MAIN_MSTP = 0,MAIN_

MODBUS = 1,MAIN_PTP = 2,SUB_GSM = 3,MAIN_ZIG = 4,SUB_ZIG = 5,SUB_MODBUS = 6

61 1 1 com2 configure MAIN_MSTP = 0,MAIN_MODBUS = 1,MAIN_PTP = 2,SUB_GSM = 3,MAIN_ZIG = 4,SUB_ZIG = 5,SUB_MODBUS = 6

62 1 1 write flash time after changed setting. Unit is minute93 1 1 Reserved100~105 1 6 reg100, MAC address, read only106 1 1 reg106, DHCP setting. 0=static IP; 1= DHCP107~110 1 4 IP address: MSB, MSB-1, MSB-2, LSB111~114 1 4 SUBNET MASK address: MSB, MSB-1, MSB-2, LSB115~118 1 4 GATEWAY address: MSB, MSB-1, MSB-2, LSB119 1 1 reg119, 0, TCP server120 1 1 reg120, listen port at TCP server mode200~206 1 6 200 201 202 203 204 205 206

Last Time Sync second min hour day day of week month year

299 1 1 number of device which is connected to T3 controller300~400 1 100 id of sub tstat500~504 1 5 500 501 502 503 504

Number of AV AI AO BI BO

7000~7049 2 50 test 8000~8007 1 8 8000 8001 8002 8003 8004 8005 8006 8007

output input variable controller WR AR PRG TBL

8008~8015 1 8 8008 8009 8010 8011 8012 8013 8014 8015TZ AMON GRP ARRAY UNIT USER

NAMEALARM

SETTSTAT

8020~8083 2 64 output value, (digital output, ON - 512, OFF - 0)8084~8147 2 64 output swith status (SW_OFF - 0, SW_AUTO - 1, SW_HAND - 2)8148~8211 1 64 "output range (0 - unused) { UNUSED=0,

OFF_ON, CLOSED_OPEN, STOP_START, DISABLED_ENABLED, NORMAL_ALARM, NORMAL_HIGH, NORMAL_LOW, NO_YES, COOL_HEAT, UNOCCUPIED_OCCUPIED, LOW_HIGH, ON_OFF , OPEN_CLOSED, START_STOP, ENABLED_DISABLED, ALARM_NORMAL, HIGH_NORMAL, LOW_NORMAL, YES_NO, HEAT_COOL, OCCUPIED_UNOCCUPIED, HIGH_LOW, custom_digital1, custom_digital2, custom_digital3, custom_digital4, custom_digital5, custom_digital6, custom_digital7, custom_digital8 } Digital_units_equate;"


Address Num Length Description8212~8275 1 64 output auto or manual (0 - auto, 1- manual)8276~8339 1 64 output type, digital or analog (0 - digital 1 - analog)8340~8403 2 4 input value8404~8467 1 4 input filter8468~8531 1 4 input calibration8532~8595 1 4 input sign calibration8596~8859 1 64 "input range (not_used_input = 0, Y3K_40_150DegC,

Y3K_40_300DegF, R10K_40_120DegC, R10K_40_250DegF, R3K_40_150DegC, R3K_40_300DegF, KM10K_40_120DegC, KM10K_40_250DegF, A10K_50_110DegC, A10K_60_200DegF, V0_5, I0_100Amps, I0_20ma, I0_20psi, N0_2_32counts, N0_3000FPM_0_5V, P0_100_0_5V, P0_100_4_20ma, P0_255p_min, table1, table2, table3, table4, table5,100 - HI_SPEED_COUNTER )"

8660~8671 2 6 high speed counter1~68672~8677 1 6 high speed counter1~6 flag, 0 - start, 1 - stop, 2 -clear8678~8741 1 64 input type, 0- thermistor, 1- 5v, 2-10v, 3- 20ma8820~8947 1 128 value of VAR1-VAR1288948~9075 1 128 A/M of VAR1-VAR128

18000~ for test, tatst information30000~ for test, monitor task

Support BACnet Object Type:analog-input, analog-output, analog-value, binary-input, binary-output, device

Support BACnetService:who-is, i-am object-identifier, object-name, object-type, present-value, units, object-list, vendor-id, vendor-name, system-status, confirmed-service, unconfirmed-service


BIP objectT3-BB T3-LB T3-TB

Analog-variable AV1-10 AV1-10 AV1-10Analog-input: AI1~32 AI1~16 AI1~11

For BB, LB, TB, if add expansion modules, maximum inputs can reach to 64Analog-output: AO1~12 AO1~4 AO1~4Binary-output: BO1~12 BO1~6 BO1~2

Outputs: For BB, LB, TB, if add expansion modules, maximum outputs can reach to 64. T3-TB itself has total 8 outputs, while there are 2 universal ouputs can be used as analog output, or binary output.

Device: obect-identifierobject-nameobject-list
