A W O R L D O F C O M F O R T
ANTI-IDLING, EMISSION REDUCING EQUIPMENT
Espar Heater Systems
V E H I C L E H E A T E R S | T E C H N I C A L D O C U M E N T A T I O N
TECHNICAL DESCRIPTION, INSTALLATION, OPERATING, TROUBLESHOOTING, REPAIR
AND MAINTENANCE INSTRUCTIONS - HYDRONIC II 5E, HYDRONIC II.
Espar
THE INFORMATION IN THIS MANUAL IS ONLY VALID FOR
THE FOLLOWING ENGINE-INDEPENDENT WATER HEATERS
Gasoline
B 5 S – 12 V 20 1904 05 00 00
Diesel
D 5 S – 12 V 25 2526 05 00 00
CONTENTS
CHAPTER TITLE CONTENT PAGE
1 Introduction Foreword 4Special text structure, presentation and picture symbols 4Special text formats and presentations 4Picture symbols 4Safety instructions for installation and repair 4Liability claim / Guarantee 4Accident prevention 5Initial start-up of the heater or functional test after a repair 5Emergency shutdown – EMERGENCY OFF 5Diagnostic compatibility 5Heater warnings 5Disposal 6
2 Product Information Cutaway view 7Main heater dimensions 8Main water pump dimensions 8
3 Technical Data Hydronic II D 5 S diesel heater (Metric values) 9Hydronic II D 5 S diesel heater (US values) 9Hydronic II B 5 S diesel heater (Metric values) 10Hydronic II electrical consumption 10Water pump 11
4 Installation Procedures Principal dimensions - Boxed version 12Heater Location 12- Box stud dimensions 12- Heater mounting 12- Permissible installation positions 13- Installation Position with allowable swivel ranges 13- Water pump mounting 13Water pump location and mounting 14- Installation examples 14Heater bracket installation 15- Installation steps 15Heater & Engine Plumbing 17Fuel supply 18- Preferred fuel extraction 18- Installation position of the metering pump 19- Maximum suction and pressure head 19- Fuel pick-up pipe installation (Drill option) 20- Fuel quality for diesel heaters 21- Operation with biodiesel 21
2
CONTENTS
This list of contents gives you precise information about the
contents of the Troubleshooting and Repair Instructions.
CONTENTS
CHAPTER TITLE CONTENT PAGE
4 Installation Procedures continuation... Exhaust connection 22Intake connections 23Electrical connections 24
5 Heater Operation Operating switches 26Heater wiring 27Parts list for heater circuit diagram 27Pin assignment for S1 connector 27Heater circuit diagram 28Pre-start procedures 29Start up / Safety factors 29Periodic maintenance 30
6 Maintenance, Troubleshooting & Repairs Basic troubleshooting / Self Diagnostics 31Start the diagnosis query 32Fault diagnosis using the control unit 33Fault code display / Description / Information 34Repair Instructions / Special tool 40Assembly drawing and parts list 41Repair Steps / Connector Assignment (S1, B2) 42Measuring the fuel quantity without EDiTH 52Fuel quantity test with EDiTH 53
7 Parts List Heater Spare parts diagram 54Installation, water and combustion air system diagram 59Electrical and fuel system diagram 61
3
1 INTRODUCTION
FOREWORD
These Troubleshooting and Repair Instructions are applicable to
the heaters listed on the title page, to the exclusion of all liabili-
ty claims.
Depending on the version or revised status of the heater, there
may be differences between it and these trouble-shooting and
repair instructions.
The user must check this before carrying out the repair work and,
if necessary, take the differences into account.
SPECIAL TEXT STRUCTURE, PRESENTATION AND PICTURE SYMBOLS
Special text formats and picture symbols are used in these
instructions to emphasise different situations and subjects.
Please refer to the following examples for their meanings and
appropriate action.
SPECIAL TEXT FORMATS AND PRESENTATIONS
• This dot (•) indicates a list, which is started by a heading.
– If an indented dash (–) follows a "dot", this list is a subsec-
tion of the black dot.
PICTURES SYMBOLS
DANGER!
This information points out a potential serious or fatal danger.
Ignoring this information can result in severe injuries.
This arrow indicates the appropriate precaution to take to
avert the danger.
CAUTION!
This information points out a dangerous situation for a person
and / or the product. Failure to comply with these instructions can
result in injuries to people and / or damage to machinery.
This arrow indicates the appropriate precaution to take to
avert the danger.
PLEASE NOTE!
These remarks contain recommendations for use and useful tips
for the operation, installation and repair of the heater.
SAFETY INSTRUCTIONS FOR INSTALLATION AND REPAIR
CAUTION!
Improper installation or repair of Espar heaters can cause a fire
or toxic exhaust entering the inside of the vehicle.
This can cause serious and even fatal risks.
The heater may only be installed according to the specifica-
tions in the technical documents or repaired using original
spare parts by authorised and trained persons.
Installation and repairs by unauthorised and untrained
persons, repairs using non-original spare parts and without
the technical documents required for installation and repair
are dangerous and therefore are not permitted.
A repair may only be carried out in connection with the
respective unit-related technical description, installation
instructions, operating instructions and maintenance
instructions.
This document must be carefully read through before / dur-
ing installation and repair and followed throughout.
Particular attention is to be paid to the official regulations,
the safety instructions and the general information.
PLEASE NOTE!
• The relevant rules of sound engineering practice and any infor-
mation provided by the vehicle manufacturer are to be observed
during the installation and repair.
• When carrying out electric welding on the vehicle, the positive
cable at the battery should be disconnected and placed at
ground to protect the ECU.
LIABILITY CLAIM / GUARANTEE
Espar does not accept any liability for defects and damage, which
are due to installation or repair by unauthorised and untrained
persons.
Compliance with the official regulations and the safety instruc-
tions is prerequisite for liability claims.
Failure to comply with the official regulations and safety instructions
leads to exclusion of any liability of the heater manufacturer.
4
1 INTRODUCTION
ACCIDENT PREVENTION
General accident prevention regulations and the corresponding
workshop and operating safety instructions are to be observed.
INITIAL START-UP OF THE HEATER OR FUNCTIONAL TEST AFTER A REPAIR
• After installation or carrying out a repair on the heater, the
coolant circuit and the whole fuel supply system must be
vented carefully.
• Comply with the instructions issued by the vehicle manufacturer.
• During the heater trial run, all water and fuel connections must
be checked for leaks and secure, tight fit.
• If faults occur while the heater is running, use a diagnostic unit
to correct the cause of the fault.
PLEASE NOTE!
DIAGNOSTIC COMPATIBILITY
Only EDiTH and EasyStart diagnostic products are compatible
with Hydronic II heaters. Older diagnostic products like the 7day
timer, Digi Diagnostic and “Fault code retrieval device” are not
compatible.
WARNING TO INSTALLER!
Correct installation of this heater is necessary to ensure safe and
proper operation.
Read and understand this manual before attempting to install the
heater. Failure to follow all these instructions could cause serious
or fatal injury.
• Disconnect the vehicle battery before starting any kind of work.
• Before working on the heater, switch the heater off and let all
hot parts cool down.
• The heater must not be operated in closed areas, e.g. a garage
or in a multi-storey parkade.
The heater must not be mounted in the passenger compartment of
vehicles. However, a heater in a hermetically sealed enclosure
which also complies with the aforementioned conditions may be
used.
All appropriate precautions must be taken when arranging the
heater to minimize the risk of injuries to people or damage prop-
erty.
Parts related to the fuel system must not be located in the pas-
senger compartment.
WARNING - EXPLOSION HAZARD!
• Heater must be turned off while re-fueling.
• Do not install heater in enclosed areas where combustible
fumes may be present.
A warning sign is to be fixed to the intake connection indicating
that the heater must be switched off before refuelling.
WARNING - FIRE HAZARD!
• Install the exhaust system so it will maintain a minimum
distance of 50mm (2”) from any flammable or heat sensitive
material.
• Ensure that the fuel system is intact and there are no leaks.
The heater must not pose a fire hazard. This requirement is
deemed to be fulfilled if adequate clearance is ensured for all
parts during installation, sufficient ventilation is provided and
fireproof materials or heat shields are used.
5
EMERGENCY SHUTDOWN — EMERGENCY OFF
If an emergency shutdown – EMERGENCY OFF – is necessary during
operation, proceed as follows:
• Switch the heater off at the control element or
• remove the fuse or
• disconnect the heater from the battery.
1 INTRODUCTION
WARNING - ASPHYSIATION HAZARD!
• Route the heater exhaust so that exhaust fumes cannot enter
any passenger compartments.
• If running exhaust components through an enclosed compart-
ment, ensure that it is vented to the outside.
The air for the heater's combustion chamber must not be sucked
in from the vehicle's passenger compartment.
WARNING - SAFETY HAZARD ON COOLANT HEATERS USED
WITH IMPROPER ANTIFREEZE MIXTURES!
• The use of Espar coolant heaters requires that the coolant
in the system to be heated contains a proper mixture of water
and antifreeze to prevent coolant from freezing or slushing.
• If the coolant becomes slushy or frozen, the heater's coolant
pump cannot move the coolant causing a blockage of the
circulating system.
• This situation could cause engine damage and/or personal
injury. Extreme care should be taken to ensure a proper mixture
of water and antifreeze is used in the coolant system.
• Refer to the engine manufacturer for coolant recommendations
requirements.
SAFETY INSTRUCTIONS FOR APPLICATION AND PROPER PURPOSE!
The heater must only be used and operated for the range of
application stated by the manufacturer in compliance with the
“Operating instructions” included with every heater.
The factory nameplate or duplicate must be affixed so that it can
still be easily read when the heater is installed in the vehicle.
ATTENTION!
Operation with bio-diesel
HYDRONIC II D5 is not certified for use with bio-diesel.
Admixtures of bio-diesel up to a magnitude of approx. 10% are
allowed
ATTENTION!
Heating at high altitudes.
Up to 1500 meters (4920’) - unrestricted heating operation
is possible.
Above 1500 meters (4920’) - heating operation is in principle
possible for short periods, e.g. when crossing a mountain
pass or during a brief stop. In cases of extended stays, the
fuel supply at the fuel metering pump has to be adapted to
high altitude conditions.
P/N: 22 1000 33 22 00 is the high altitude device used with the
Hydronic II.
Disposal
Disposal of materials
Old devices, defective components and packaging material can all
be separated and sorted, so that all parts can be disposed of as
required in an environmentaly friendly manner and recycled when
possible.
Electric motors, control boxes and sensors (e.g. temperature sen-
sors) are deemed to be “electronic scrap”.
6
2 PRODUCT INFORMATION
7
CUTAWAY VIEW
1 Blower motor 10 Fuel Metering pump
2 ECU 11 Water pump
3 Blower impeller
4 Surface sensor
5 Overheat sensor E = Exhaust
6 Flame sensor F = Fuel
7 Combustion chamber C = Combustion air
8 Heat exchanger WO = Water outlet
9 Glow pin WI = Water inlet
WI
WO
F
CE
3
9
1
11
5
4
8
7
6
210
2 PRODUCT INFORMATION
8
MAIN HEATER DIMENSIONS
MAIN WATER PUMP DIMENSIO NS
E = ExhaustF = FuelC = Combustion airWI = Water inletWO = Water outlet
WI = Water inletWO = Water outlet
E
F
C
WIWO
WI
WO
20
89.7
2024 39 39
60
20
102 94 13
68
9
20.5
118.5
29.5
132
71.5
8
21.5 16
85.7
86(3.39
59
54
17.2
3 TECHNICAL DATA
9
HYDRONIC II D 5 S DIESEL HEATER (METRIC VALUES)
Heater type Hydronic II
Heater version D 5 S
Heating medium Mixture of water and coolant (max. 50 % coolant)
Voltage 12 volt
Control stage Power High Low
Heat output (watt) 5200 5000 2100
Fuel consumption (l/h) 0.64 0.61 0.26
Allowable operating pressure up to 2.5 bar overpressure max.
Minimum water flow rate of the heater 250 l/h
Allowable ambient temperature During operation Without operation
Heater, continuous –40 °C to +80 °C –40 °C to +110 °C
Heater, short time – – – +125 °C (5 x 2 h)
Coolant water temperature
continuous –40 °C to +120 °C –40 °C to +120 °C
short time – – – +125 °C (1 h)
Weight – without coolant and attachments 2.4 Kg
HYDRONIC II D 5 S DIESEL HEATER (US VALUES)
Heater type Hydronic II
Heater version D 5 S
Heating medium Mixture of water and coolant (max. 50 % coolant)
Voltage 12 volt
Control stage Power High Low
Heat output (BTU) 17,755 17,072 7,170
Fuel consumption (US gal/h) 0.169 0.161 0.069
Allowable operating pressure up to 36.26 psi bar overpressure max.
Minimum water flow rate of the heater 1.1 US gpm
Allowable ambient temperature During operation Without operation
Heater, continuous –40 °F to +176 °F –40 °F to +230 °F
Heater, short time – – – +257 °F
Coolant water temperature
continuous –40 °F to +248 °F –40 °C to +248 °F
short time – – – +257 °F
Weight – without coolant and attachments 5.28 lb
3 TECHNICAL DATA
10
HYDRONIC II B 5 S DIESEL HEATER (METRIC VALUES)
Heater type Hydronic II
Heater version B 5 S
Heating medium Mixture of water and coolant (max. 50 % coolant)
Voltage 12 volt
Control stage Power High Low
Heat output (watt) 5200 5000 2300
Fuel consumption (l/h) 0.72 0.69 0.32
Allowable operating pressure up to 2.5 bar overpressure max.
Minimum water flow rate of the heater 250 l/h
Allowable ambient temperature During operation Without operation
Heater, continuous –40 °C to +60 °C –40 °C to +105 °C
Heater, short time – – – +125 °C (5 x 2 h)
Coolant water temperature
continuous –40 °C to +120 °C –40 °C to +120 °C
short time – – – +125 °C (1 h)
Weight – without coolant and attachments 2.4 Kg
HYDRONIC II ELECTRICAL CONSUMPTION
Heater type Hydronic II
Heater version B 5 S, D 5 S
Rated voltage 12 volt
Control stage Power High Low
Average electrical consumption without pump (watts) Operation 40 37 12
Start up 120
3 TECHNICAL DATA
WATER PUMP
CAUTION!
Operating the water pump outside the specified technical data
can cause malfunctions.
The technical data must be complied with at all times.
PLEASE NOTE!
If no limit values are given, the technical data listed is with the
usual heater tolerances of ± 10 % at nominal voltage and 800 ft
altitude.
11
Rated voltage 12 volt
Operating voltage 9 volt to 16 volt
Electrical power consumption < 15 watt
Delivery rate 680 l/h 2.99 US gpm
Delivery pressure difference 0.1 bar 1.5 psi
Operating temperature –40 °C to +125 °C (-40°F to 257°F)
Volumetric ow rate Q (l/h)
Del
iver
y pr
essu
re P
(bar
)
0,25
0,300.18 USgpm @ 290psi 2.20 USgpm @ 189psi
4.40 USgpm @ 0.79 psi
0,20
0,15
0,10
0,05
00 100 200 300 400 500 600 700 800 900 1000
4 INSTALLATION PROCEDURES
12
PRINCIPAL DIMENSIONS - BOXED VERSION
HEATER LOCATION
Always mount the heater in a protected area. Eg: storage com-
partment, engine compartments, step box or battery box.
Espar recommends you use the boxed unit.
When mounting the heater adhere to the following conditions:
• Situate the heater below the normal coolant level of the engine.
• Guard against excessive road spray.
• Keep coolant hoses, fuel lines and electrical wiring as short as
possible.
BOX STUD DIMENSIONS
HEATER MOUNTING
If your heater is boxed it must be mounted level with the exhaust
pointing towards the ground. If your heater is not boxed fallow
the mounting instructions for the heater and the water pump on
the fallowing pages.
The heater must not pose a fire hazard.
– This requirement is deemed to be fulfilled when adequate clear-
ance to all parts is observed during installation, sufficient venti-
lation is provided and fireproof materials or heat plates are used.
The heater must not be located in the passenger compartment.
A unit may however be used in a hermetically sealed housing
which also corresponds to the conditions stated above.
The factory nameplate or duplicate must be affixed so that it can
still be easily read when the heater is installed in the vehicle.
All appropriate precautions must be taken when arranging the
heater to minimise the risk of injuries to people or damage
property.
DANGER — RISK OF INJURIES AND BURNS!
The coolant and components of the coolant circuit get very hot.
• Parts conveying water must be routed and fastened in such a
way that they pose no temperature risk to people, animals or
material sensitive to temperature from radiation / direct contact.
• Before working on the cooling water circuit, switch the heater
off and wait until all the components have cooled down
completely, if necessary wear protective gloves.
PLEASE NOTE!
Do not install the water pump at the lowest point in the water
circuit, otherwise the particles in the water circuit settle in the
water pump. A water filter must be used if the cooling water is
highly soiled/contaminated with particles.
CAUTION!
Protect the heater from excessive road spray to avoid internal
corrosion.
PLEASE NOTE!
The installation position of the water pump with the pump head
facing downwards is not advantageous for automatic venting.
– The water pump can be installed in any position.
– The water inlet must be designed so that it is always comple-
tely filled with water (the water pump is not selfpriming).
216 mm(8.5”)
310 mm(12.2”)
39 mm(1.5”)
229 mm(9”)
310 mm(12.2”)
55.25 (2.18”)
114.5 (4.5”)
37.3(1.47”)
228.6(9.0”)
4 INSTALLATION PROCEDURES
PERMISSIBLE INSTALLATION POSITIONS
The heater and the water pump should preferably be installed in
the normal position. Depending on the installation conditions, the
heater can be installed within the permissible ranges shown
below.
INSTALLATION POSITION WITH ALLOWABLE SWIVEL RANGES
WATER PUMP MOUNTING
Mount the water pump bracket to the heater as shown in the
examples below. (torque 6+2 Nm ~ 4.4 ft-lb) or in a suitable posi-
tion within the vehicle, depending on the installation conditions.
Then insert the water pump in the rubber mount and press in until
the water pump is locked into position.
13
max. 90°
max. 90°
Heater in horizontal installation position (normal posi-tion*) with permissible swivel range up to the vertical installation position.All installation positions between 0° and 90° are per-mitted.
Heater upright in horizontal installation position (normal position*) with permissible swivel range up to the hori-zontal installation position.All installation positions between 0° and 90°are per-mitted.
Please note!
If a heater is swivelled out of the normal posi-tion, the fuel connections must always be at the bottom.
4 INSTALLATION PROCEDURES
14
WATER PUMP LOCATION AND MOUNTING
The water pump bracket included in the installation kit must be
fixed to the heater (see installation examples below) or in a
suitable position in the vehicle, depending on the installation
conditions.
Then insert the water pump in the rubber element and press in
until the water pump has latched into position.
INSTALLATION EXAMPLES
Heater with angled water inlet connection. The water pump is
fixed to the bottom of the heater, on the "fuel connection" side.
The water discharge connection of the water pump faces to the side.
The water pump is fixed to the "fuel connection" side of the
heater with rising water inlet connection. The water discharge
connection of the water pump faces upwards.
The water pump is fixed to the "fuel connection" side of the
heater with the water inlet connection facing downwards. The
water discharge connection of the water pump faces upwards.
Heater with angled water inlet connection. The water
pump is fixed to the bottom of the heater, on the "water
outlet connection" side. The water discharge connection
of the water pump faces to the side.
The water pump is fixed to the "water outlet connection" side of
the heater with rising water inlet connection. The water discharge
connection of the water pump faces upwards.
The water pump is fixed to the "water discharge connection" side
of the heater with the water inlet connection facing downwards.
The water discharge connection of the water pump faces upwards.
4 INSTALLATION PROCEDURES
HEATER BRACKET INSTALLATION
Use the bracket included in the installation kit to fix the heater in
a suitable position on the vehicle.
INSTALLATION STEPS
1. Improper installation or repair of Espar heaters can cause a
fire or toxic exhaust entering the inside of the vehicle.
2. Mount special screw M6 x 17 onto the heater.
3. Hook heater into the bracket.
15
Mount with 3 screws or fixing with 4 screws.
Mount special screw M6 x 17 (with adhesive coating) on heater on the fuel connection side (left-hand Fig.)
or on the water discharge connection side (right-hand Fig.) (tightening torque: 6+2 Nm ~ 4.4 ft-lb).
4. Use 2 hexagon screws M6 x 12 (with adhesive coating) to fix
heater to the bracket (tightening torque 6+2 Nm ~ 4.4 ft-lb).
4 INSTALLATION PROCEDURES
16
PLEASE NOTE!
• When installing the heater and the water pump, please note the
direction of flow of the cooling water circuit.
• Fill the heater and water hose with coolant before connecting to
the coolant circuit.
• Route the water hoses without any kinks, and in a rising posi-
tion if possible.
• When routing the water pipes, maintain sufficient clearance
from hot vehicle parts.
• Protect all water hoses / water pipes from chafing and from
extreme temperatures.
• Secure all hose connections with hose clips (tightening torque:
3+0.5 Nm ~ 2.2 ft-lb).
• Re-tighten the hose clips after the vehicle has been running for
2 hours or has travelled 100 km.
• The minimum water flow rate is only guaranteed if the tempe-
rature difference of the heating medium does not exceed 10°C
(18°F) between water inlet and water outlet during heating.
• Only overpressure valves with an opening pressure of min. 0.4 –
max. 2 bar (5.8 - 30 psi) may be used in the cooling water circuit.
• As corrosion protection the cooling water must contain at least
10 % coolant (anti-freeze).
• During cold periods the coolant water must contain sufficient
coolant (antifreeze).
• Before commissioning the heater for the first time or after
changing the cooling water, the whole cooling water circuit
including the heater must be vented without bubbles according
to the vehicle manufacturer's instructions.
• Only top up with coolant approved by the vehicle manufacturer.
4 INSTALLATION PROCEDURES
HEATER AND ENGINE PLUMBING
Take the coolant from a low point on the engine to reduce
aeration in the system.
Ensure proper direction of coolant flow by taking coolant from a
high pressure point in the engine and returning it to a low
pressure point. (ie. pickup from back of block and return to the
suction side of the engine's water pump).
Ensure adequate flow rate through the heater by comparing the
incoming and outgoing coolant temperatures while the heater is
running. If the rise in temperature exceeds 10°C (18°F), coolant
flow must be increased by modifying the plumbing.
If a bunk heat exchanger is incorporated into the system, proper
plumbing layouts must be followed.
CAUTION!
It is possible for the coolant and components of the coolant circuit
to get very hot.
1 Heater
2 Water pump
3 Connector (optional)
4 Heat exchanger
5 Vehicle engine
17
5 3 3
4
21
4 INSTALLATION PROCEDURES
18
FUEL SUPPLY
PREFERRED FUEL EXTRACTION — IN GASOLINE OR DIESEL
VEHICLES
1 Fuel pick-up pipe = Ø 2 mm
2 Adapter, Ø 5.0 / 3.5 mm
3 Fuel metering pump
4 Fuel filter – (optional)
5 Plastic fuel line, Ø 2 mm, Espar black or blue line recomended
6 Plastic fuel line, Ø 2 mm
7 Rubber fuel line Ø 3.5 mm
8 Elbow, 105°
CAUTION!
Safety instructions for the fuel supply!
The fuel must not be discharged by means of gravity or
overpressure in the fuel tank.
MAXIMUM FUEL LINE LENGTHS
Intake side
a = 2 m (6.5’)
Pressure side
b = 6 m (19.5’)
1
2 5
4
7 37
7
6 87
6
a
b
4 INSTALLATION PROCEDURES
INSTALLATION POSITION OF THE METERING PUMP
Always install the metering pump with the delivery side rising
upwards.
Any mounting position over 15° is allowed, although a mounting
position between 15° and 35° is preferable.
MAXIMUM SUCTION AND PRESSURE HEAD OF THE METERING PUMP
Pressure head from fuel tank to metering pump:
a = 3000 mm (9.8’)
b = 1000 mm (3.2’) (gasoline = 500 mm (1.6’))
Suction head in a fuel tank in which negative pressure to 0.03 bar
(0.4 psi):
b = 400 mm for diesel (1.3’) (gasoline = 150mm (0.5’)
Pressure head from the fuel metering pump to the heater:
c = 2000 mm (6.6’)
PLEASE NOTE!
Check tank ventilation.
CAUTION!
SAFETY INSTRUCTIONS FOR INSTALLING THE METERING PUMP!
Always install the metering pump with the delivery side
rising upwards – minimum angle 15°.
Protect the metering pump and filter from impermissible
heating, do not install close to silencers and exhaust pipes.
1 Installation position within range 0° – 15° is not allowed
2 Preferred installation position within range 15° – 35°
3 Installation position within range 35° – 90° is allowed
1 Connection at the heater
2 Max. fuel level
3 Min. fuel level
19
4 INSTALLATION PROCEDURES
20
FUEL PICK-UP PIPE INSTALLATION (DRILL OPTION)
• Choose a protected mounting location close to the pump and
heater. A spare fuel sender gauge plate provides an ideal
mounting location. If one is not available...
• Drill mounting holes in tank to accommodate pick-up pipe as
shown.
• Tighten Ferrule nut to pick-up pipe at desired height.
• Cut the fuel pick-up pipe to length. Allow 2-2.5” from bottom
of tank.
• Mount the fuel pick-up pipe as shown.
• Lower the fuel pick-up pipe (with reinforcing washer) into the
tank using the slot created by the two 0.6cm (1/4”) holes.
• Lift the assembly into position through the 2.5cm (1”) hole.
• Assemble the rubber washer, metal cup washer and nut.
PLEASE NOTE!
Some pick-up pipes can be installed by either drill or NPT.
ø 2.5cm (ø1.0”)
1.5cm(9/16”)
1.5cm(9/16”)
ø 0.625 cm (2 Holes)(ø 1/4”)
Drill the two (1/4”) holes first
Fuel Pi pu-kcFerrul Nut (Tighten before installing)NutSheet Metal Washer(raised center to top)
Reinforcing WasherHolding Tabs
Allow 2" from FuelPick-up to tank bottom.Allow only 1" for flatbottom tanks.
Fuel Tank
FMP bracket
4 INSTALLATION PROCEDURES
FUEL SUPPLY
FUEL QUALITY FOR DIESEL HEATERS
• The heater runs problem-free on standard grade diesel fuel.
• Always use fuel that is appropriate for the temperature that the
heater is being used in.
At external temperatures of 0 °C to –20 °C, use Winter diesel
(32 °F to –4 °F)
At external temperatures of –20 °C to –40 °C, use Arctic diesel
or polar diesel (-4 °F to –40 °F).
OPERATION WITH BIODIESEL
HYDRONIC II D5 is not certified for use with bio-diesel.
Admixtures of bio-diesel up to a magnitude of approx. 10%.
PLEASE NOTE!
• Additions of used oil are not allowed!
• After refuelling with winter or cold diesel, the fuel pipes and the
metering pump must be filled with the new fuel by letting the
heater run for 15 minutes!
• Quelity of fuel will vary from manufacturer and location.
• Use of fuel additives may result in adverse effects.
21
4 INSTALLATION PROCEDURES
22
EXHAUST CONNECTION
The exhaust system consists of a Ø 24mm flexible exhaust pipe.
An optional exhaust silencer is available.
• Connect the exhaust pipe to the exhaust port on the heater and
attach with clamp provided. (tightening torque: 7+0,5 Nm ~ 5 ft-lb)
• Run exhaust to an open area to the rear or side of the vehicle
so that fumes can not build up and enter the passenger
compartment or the heater combustion air intake. Insure that
the pipe is fastened securly. Observe warnings stated in this
section and through out the manual.
• Install exhaust pipe with a slight slope or drill a small hole in
the lowest point to allow water to run out. Any restriction in
exhaust will cause operational problems.
• Securing the exhaust can be done with "p" clamps like the ones
provided in our standard installation kits.
CAUTION!
Run exhaust so that it cannot be plugged by dirt, water or snow.
Ensure the outlet does not face into the vehicle slip stream. Lay
the exhaust system so that the outflowing exhaust gases are not
sucked in as combustion air.
1 Heater
2 Combustion air hose
3 Flexible exhaust pipe
The exhaust is hot, keep a minimum of 5cm (2”) clearance from
any heat sensitive material.
Route exhaust so that the exhaust fumes cannot enter the
passenger compartment.
Every type of combustion produces high temperatures and toxic
exhaust fumes. This is why the exhaust system must be routed
according to these installation instructions.
• Do not perform any work on the exhaust system while the
heater is working.
• Before working on the exhaust system, switch off the heater
first and wait until all the parts have completely cooled down,
wear safety gloves if necessary.
• Do not inhale exhaust fumes.
Ensure exhaust pipe ends in open air. Mount the exhaust pipe
with sufficient clearance to heat-sensitive parts. Pay particular
attention to fuel pipes (made of plastic or metal), electrical
cables and brake hoses, etc.!
4 Exhaust silencer
5 Exhaust pipe end with end sleeve
6 Spacer ring
max. 760 mm max. 2 m
min. 200 mmmin. 200 mm
min. 150 mm
4 INSTALLATION PROCEDURES
INTAKE CONNECTION
The combustion air must be drawn out of an area which does not
become hotter than 25°C (77°F) and in which neither spray water
or dust / dirt are to be expected.
The Ø 20 mm flexible combustion air hose must be secured to the
heater with a hose clamp (tightening torque 3+0.5 Nm - 2.2 ft-lb)
CAUTION!
The combustion air opening must be free at all times.
Lay the combustion air intake to ensure that exhaust fumes
cannot be sucked in as combustion air.
Arrange the combustion air intake so that it is not directed
against the slipstream of the vehicle.
The combustion air intake must not become clogged with dirt
and snow.
Install the combustion air intake system sloping slightly
downwards. If necessary, make a drain hole approx. Ø 5 mm
(3/16”) at the lowest point to drain off condensation.
23
4 INSTALLATION PROCEDURES
24
-+
B
C
D
A
E
VehicleChassis EasyStart T
ELECTRICAL CONNECTIONS
All parts needed are included with all standard installation kits.
A. Main Heater H arness • Connects switch and power harness to the heater harness.
B. Power Harness • 2 core harness (red, brown).
• Connect red wire to fuse l ink and terminal .
• Attach r ing terminal to vehicle battery (+) .
• Connect brown wire to vehicle battery (- ) using r ing terminal provided.
• 20 amp fuse - 12V.
C. Switch Harness • 4 core harness (red, brown, yel low, blue/white) .
• Run to locat ion of control opt ion. Make terminal connect ions at control opt ion.
D. Fuel Metering Pump Harness • 2 core harness (green, green) or (green, brown).
• Connect to fuel metering pump using terminals and protective seals + connector block.
E. Water Pump Harness • 2 core harness (black, brown).
• Connect to main harness at heater.
HYDRONIC I I HEATER
CAUTION!
To avoid potential short circuit damage during installation, insert 20
amp fuse on power harness after all electrical connections are complete.
PLEASE NOTE!
• Negative battery terminal must always be grounded.
If a vehicle is equipped with switch on negative battery wire,
install additional 20 A fuse in negative wire of heater’s harness.
• All harnesses should be cut to length.
All exposed electrical connections should be coated with pro-
tective grease.
• Wire must be inserted into fuse holder prior to terminating.
NOTES:
25
5 HEATER OPERATION
26
OPERATING SWITCHES
EasyStart T
• Manual On / Off of heater.
• Program up to 3 start times, up to 7 days ahead.
• Has ability to read diagnostic fault codes.
Push / Pull Switch
• Manual On / Off of heater.
7-Day Timer
• Manual On / Off of heater.
• Program Start up to 7 days ahead. (not every day of the week)
• Diagnostic not compatible with HII heaters
Mini Timer
• Manual On / Off of heater.
• Program Start up to 24 hours ahead.
• No Diagnostic capability
Progamable Timer
• Manual On / Off of heater.
• Program up to 8 start times per day, multiple days of the week.
(eg. Mon – Fri, Mon – Sun…)
• No Diagnostic capability.
PLEASE NOTE!
DIAGNOSTIC COMPATIBILITY
Only EDiTH and EasyStart diagnostic products are compatible
with Hydronic II heaters. Older diagnostic products like the 7day
timer, Digi Diagnostic and “Fault code retrieval device” are not
compatible.
For more information on these and other control options please
visit www.espar.com/help.
OK
I AUTO O RUN P
P 1...7 h m
1 2 3 4 5 6 7 P M
R
5 HEATER OPERATION
HEATER WIRING
CAUTION!
SAFETY INSTRUCTIONS FOR WIRING THE HEATER!
The heater is to be connected up electrically according to the
local standards.
Ensure that the insulation of electrical cables is not damaged.
Avoid:
– chafing, kinking, jamming or exposure to heat.
– Seal empty terminal chambers with filler plugs to ensure they
are dirt-proof and water-proof.
– Electrical connections and ground connections must be free
of corrosion and firmly connected.
– Lubricate connections and ground connections outside the
heater interior with contact grease.
PLEASE NOTE!
Comply with the following when wiring the heater and the control
unit:
• Electrical leads and components must be positioned in the vehi-
cle so that they can function perfectly under normal operating
conditions without impairment (e.g. due to heat exposure, mois-
ture, etc.).
• Ensure that the proper gauge of wire is used for your installa-
tion.
PARTS LIST FOR HEATER CIRCUIT DIAGRAM
Parts list for heater circuit diagram
1.1 Burner motor
1.2 Glow plug
1.5 Control - overheating sensor
1.12 Flame sensor
1.13 Surface sensor
2.1 ECU
2.2 Fuel metering pump
2.5.7 Vehicle blower relay
2.7 Main fuse, 20 A
2.7.1 Control fuse, 5 A
2.7.5 Vehicle blower fuse, 25 A
2.12 Water pump
5.1 Battery
b) Vehicle blower connection
PLEASE NOTE!
The relay, 12 volt 2.5.7 (from terminal 30 to terminal 87a) has a
maximum power consumption of 40 A; i.e. the value of the vehi-
cle's own blower fuse may not be more than 40 A. For circuit
diagram, see page 28.
PIN ASSIGNMENT FOR S1 CONNECTOR
Pin# Wire color Function
1 Red (rt) Battery (+) positive
2 Brown (br) Battery (-) minus
3 Black / Red (sw/rt) Vehicle Blower signal
4 Green (gn) FMP (+) signal
5 Blue / White (bl/wt) Diagnostic signal
6 Blue / White (bl/wt) Auxiliary heating input
7 Yellow (ge) Heater on signal
8 Violet (vi) Water pump (+)
9 Brown (br) Water pump (-)
10 Brown / Green (br/gn) FMP (-)
27
B2 B1 S1 B8 S8 B6 S6
5 HEATER OPERATION
28
HEATER CIRCUIT DIAGRAM
5 HEATER OPERATION
PRE-START PROCEDURES
• Check all fuel, electrical and plumbing connections.
• Refill the engine coolant.
• Bleed air from the coolant system by running the engine and
refilling the antifreeze as needed. Resecure heater hose.
• Run engine to further bleed the system.
• Top up engine coolant.
START UP / SAFETY FACTORS
Once the heater is switched on the fallowing sequence occurs:
The water pump starts up, then the combustion air fan, glow plug
and metering pump are started.
The time-controlled glow plug is switched off once a stable flame
has formed in the combustion chamber.
Depending on the heat requirements, the heater runs at the
following levels: Power – High – Low – Standby. The temperature
thresholds for these are permanently programmed in the elec-
tronic control unit (ECU).
The heater starts in “Power” control stage.
After the coolant temperature has reached approx.
65 °C (149 °F) – depending on the selected blower setting – the
heater switches to the "High" control stage.
If the cooling water continues to rise up to 80 °C (176 °F), the
heater switches to "Low" control stage.
• If the heat output achieved in “Low” control stage is insuffi-
cient, the cooling water temperature drops to 75 °C (167 °F ) –
the heater switches back to “High” control stage.
• If the heating output in “Low” control stage is inadequate,
the cooling water temperature rises to 85 °C (185 °F ) .
The heater switches to Standby and is followed by an after-run,
90 seconds.
• If the coolant temperature cools to 75 °C (167 °F ) during
standby, a controlled start occurs in a high control stage.
Safety checks before starting up the heater.
After a lengthy stoppage (summer months), check all components
for secure fit (tighten screws where necessary).
Carry out a visual check of the fuel system for leaks.
• The heater is restarted if it does not ignite within 70 seconds.
The heater is automatically shut down if two attempts are made and the
heater fails to start within the preset safety period (240 seconds).
After an impermissible number of failed start attempts, the ECU
is locked.
• If the flame independently goes out during operation, the heater
is restarted and if necessary, a maximum of two further start
attempts are made within the preset safety time.
If the heater does not ignite or ignites but goes out again
within 15 minutes, a safety time out occurs.
The safety time out can be cancelled by briefly switching off
and on again (ignition ON/OFF).
• In the case of overheating (e.g. insufficient coolant flow , air in
coolant system), the overheating sensor triggers, the fuel pump
is stopped and the heater is automatically shut down. Once the
cause of the overheating has been eliminated, the heater can be
re-started by switching off and on again (ignition ON/OFF).
The coolant temperature needs to be less then 70 °C (158 °F) in
order for the heater to restart.
After an impermissible number of shut-downs on overheating,
the ECU is locked.
• If the lower or upper voltage limit is reached, the heater is
automatically shut down.
• The heater does not start up if the glow pin is defective or if the
electric cable to the metering pump is interrupted.
• The speed of the blower motor is continuously monitored. If the blower
motor does not start up, if it is blocked or if the speed falls below 40 %
of the desired speed, the heater is automatically shut down after 60sec.
PLEASE NOTE!
If the heater fails to start the first time it will automatically
attempt a second start. If the second attempt is unsuccessful the
heater will shut down completely. On initial start up the heater
may require several start attempts to prime the fuel system.
29
EMERGENCY SHUTDOWN — EMERGENCY OFF
If an emergency shutdown – EMERGENCY OFF – is necessary during
operation, proceed as follows:
• Switch the heater off at the control unit or
• remove the fuse or
• disconnect the heater from the battery.
5 HEATER OPERATION
30
CAUTION!
Do not repeat the switching off / on routine more than twice.
WARNING!
The heater must be switched off while any fuel tank on the
vehicle is being filled.
The heater must not be operated in garages or enclosed areas.
PERIODIC MAINTENANCE
• Check coolant hoses, clamps, and make sure all valves are open.
Maintain the engine manufacturers recommended coolant level
and ensure that the heater is properly bled after service on or
involving the coolant system.
• Visual check of all fuel lines for leaks. If applicable check fuel
filter inserts and replace if necessary.
• Visual check of electrical lines and connections for corrosion.
• Run your heater at least once a month during the year (for a
minimum of 15 minutes).
• Maintain your batteries and all electrical connections in good
condition. With insufficient power the heater will not start.
Low and high voltage cutouts will shut the heater down
automatically.
• Use fuel suitable for the climate. Blending used engine oil with
diesel fuel is not permitted.
• Replacing the glow pin screen and cleaning ventilation hole
before the winter season is recomended, for guaranteed start up.
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
BASIC TROUBLESHOOTING
In the event of failure there are several items which should be
checked first before any major troubleshooting is done.
Check:
• Fuses.
• Electrical lines and connections.
• Interference in Combustion air and Exhaust pipes.
• Fuel in the tank.
• Battery voltage on heater side of harness.
• Coolant flow.
SELF DIAGNOSTICS
The heater is equipped with self diagnostic capability. You can
retrieve information on the heaters last 5 faults using the
EasyStart diagnostic or ISO adapter and computer (EDiTH).
PLEASE NOTE!
The 7 day timer. FCR and the Digi Diagnostic cannot be used to
read diagnostic fault codes from the Hydronic II heaters.
PLEASE NOTE!
Always connect in the given order!
• The plug-in "diagnosis" connection may not be disconnected
until the heater has been switched off and the after-running
has finished!
• Check whether version S3V10-F (on newer) of the EDiTH soft-
ware required for the diagnosis has been installed on the PC,
if necessary the latest version can be downloaded from:
www.espar.com/help
• Follow the operating instructions for EDiTH diagnostics soft-
ware.
31
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
32
A Plug-in "diagnosis" connection
B Adapter cable
C EDiTH diagnosis tool (ISO Adapter)
D PC
E Serial cable
F Main heater harness
1 3 pin connector housing
2 6 pin receptacle housing
3 6 pin tab connector housing
START THE DIAGNOSIS QUERY.
• Double-click the ‹EDiTH› icon on the Desktop to start the
diagnostic software The EDiTH Start window opens.
• Double-click the ‹flame› button ‹Heaters and test selection›
window opens.
– Select the heater by its ‹Version No.› or via the ‹Automatic
search›.
• In the ‹Test› window, double-click ‹General Data +Fault Memory›
to open the ‹Fault memory› window.
– The fault code of the current fault/error is and the fault code
of faults/errors F1 – F5 are displayed.
DELETE THE FAULT MEMORY AND AT THE SAME TIME CANCEL THE
CONTROL BOX LOCK
• In the "Fault memory" window, press the "Delete fault memory"
button in the menu bar.
– The whole fault memory is deleted and the control box is
unlocked.
F
A
B
CD
E
1 23
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
FAULT DIAGNOSIS USING THE CONTROL UNIT
DIAGNOSIS CAPABLE CONTROL UNIT
• EasyStart T timer: 22 1000 32 88 00
If faults occur in the heater while it is running, they are displayed
with "Err" after the mobile unit or timer has been activated.
The current fault and the stored faults "F1“ to "F5“ can be queried.
PLEASE NOTE!
• The blue/white diagnostics cable must be connected in order to
perform the diagnosis.
• Fault code, fault description, cause / remedial action are
described from page 34.
• Ensure sufficient battery voltage (min. 10.5 volt).
Back button
Next button
ON / OFF activation button
OK button (symbol selection / input confirmation)
QUERY / DELETE FAULT MEMORY AND CANCEL THE HEATER LOCK
Activate mobile unit / timer
(EasyStart T operating instructions)
Confirm symbol with .
Heater is switched on.
Confirm operating time with .
Following activation, the following can be shown
in the display (display appears after approx. 20 sec.):
Display if errors/faults exist Display if no errors/faults exist
The following actions are possible with both displays:
• Display current fault in fault memory.
and at the same time briefly press .
• Display fault memory F1 – F5
or press .
The current fault is always written in fault memory F1.
• Display fault memory again.
or, at the same time, briefly press .
• Delete the fault memory and as a result, at the same time cancel
the control box lock.
Confirm current fault or one of the faults F1 – F5
with .
Confirm dEL display again with .
The fault memory is deleted and the control box is unlocked.
• Switch off the heater.
press.
33
34
FAULT CODE FAULT DESCRIPTION INFORMATION
DISPLAY
000 No faults — —
009 Air pressure sensor - communication Communication lost between the ECU and air pressure sensor.
error • Read air pressure sensor fault memory (can only be read with EDiTH diagnostic
software).
• Check wiring and connections.
• If sensor is ok, test ECU.
010 Overvoltage > 15 volt applied to ECU for at least 20 seconds without interruption
• Disconnect connectors B1/S1,measure voltage at connector B1 – between pin 1,
(red) and pin 2, (brown).
Check power source.
011 Undervoltage < 10.5 volt applied to ECU for at least 20 seconds without interruption
• Vehicle engine off, disconnect connector B1/S1, measure voltage in connector
B1 – between pin 1 (red), and pin 2, (brown).
Check the fuses, the supply cables, and connections at the battery for voltage
drop (corrosion).
012 Overheat - overheat sensor level 1 Temperature at overheating sensor >125 °C
• Check coolant circuit:
– Check water circuit for leaks.
– Vent water circuit.
– If check if all parts in coolant system are directing flow in the correct direction.
• Check if flow rate meets specification.
• Check overheat sensor:
– Check wires for continuity, short circuit and damage.
– Measure the resistance in connector B2 – between pin 10, (black) and pin 11,
(black), see page 46 for measured values.
• Check water pump, see Fault code 041 and 042.
013 Overheat - threshold temperature Temperature values of the overheating sensor and the surface sensor is too large.
014 difference exceeded. • For remedial action see Fault code 012.
(before FMP starts.) • Check the surface sensor:
– Check wiring for continuity, short circuit and damage.
PLEASE NOTE! – Measure the resistance in connector B2 – between pin 7, (black) and pin 8,
Fault code 014 is only displayed if (black), see page 47 for measured values.
the heater is running and the wa-
ter temperature at the overheating
sensor has reached at least 80 °C.
015 ECU lockout - too many overheats The ECU is locked due to consecutive overheating (Fault code 012, 013, 014, 016).
• For remedial action see Fault code 013.
• Unlock ECU, see from pages 32 - 33.
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
35
FAULT CODE FAULT DESCRIPTION INFORMATION
DISPLAY
016 Overheat - threshold temperature Temperature values of the overheating sensor and the surface sensor is too large.
difference exceeded. • For remedial action see Fault code 012.
(after FMP starts.) • Check the surface sensor:
PLEASE NOTE! – Check wiring for continuity, short circuit and damage.
Fault code 016 is only displayed if – Measure the resistance in connector B2 – between pin 7, (black) and pin 8,
the heater is running and the water (black), see page 47 for measured values
temperature at the overheating
sensor has reached at least 80 °C.
017 Overheat - Overheat sensor level 2 Temperature at overheating sensor >130 °C
threshold exceeded • For remedial action see Fault code 012.
• Check the surface sensor:
– Check wiring for continuity, short circuit and damage.
– Measure the resistance in connector B2 – between pin 7, (black) and pin 8 (black)
– see page 47 for measured values.
018 Glow pin – start energy too low Glow plug energy input is too low.
019 Glow pin – ignition energy too low • Perform functional check on the glow pin, see Fault code 020.
020 Glow pin – open circuit • Check wiring for continuity, short circuit and damage.
021 Glow pin – short circuit – Perform functional check on the glow pin in installed condition.
022 Glow pin – transistor error – Connector B2 – pin 3, (brown) and pin 6, (black), unclip both cables.
– Apply 9.5 V ±0.1 V voltage to the glow pin and after 25 sec measure the current.
CAUTION! – If 9.5 A (+1 A / –1.5 A) the glow plug is ok.
The glow plug is irreparably damaged
if the voltage values are exceeded.
Perform the functional check
with max. 9.5 volt.
PLEASE NOTE!
Ensure the power pack has ade-
quate short-circuit resistance.
025 Diagnostic communication error • Check the diagnostics cable:
Connector B1 – pin 5 and connector S8 – pin 2, check blue/white wire for conti-
nuity, short circuit and damage, if ok test ECU, see Fault code 90.
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
36
FAULT CODE FAULT DESCRIPTION INFORMATION
DISPLAY
030 Blower speed out of range Impeller blocked (frozen, soiled, sluggish, ...)
• Remove blockage and manually turn the impeller to check if it spins smoothly.
• Measure the speed using a non-contact r.p.m. counter, see page 48.
Disconnect connector B2 – apply power (+,red) to pin 13 (black) and apply ground
(-, brown) to pin 14 (brown), use 8.2 volt (+ 0.2 volt).
– Speed <10000 rpm replace the combustion air fan.
– Speed > 10000 rpm test the ECU.
031 Blower – open circuit • Check blower wiring:
032 Blower – short circuit Check connector B2 – pin 13 (black) and pin 14, (brown) for continuity, short circuit
035 Blower – transistor error and damage.
Perform the speed measurement, see Fault code 30.
CAUTION!
The motor is irreparably damaged if
the voltage values are exceeded.
Perform the functional check
with max. 8.2 volt.
PLEASE NOTE!
• Ensure correct connection of the
plus (positive) and minus (negative)
cables.
• Ensure the power pack has ade-
quate short-circuit resistance.
038 Vehicle blower – open circuit • Check vehicle blower harness:
039 Vehicle blower – short circuit Check connector B1 – pin 3, (black/red) and pin 2, (brown) for continuity, short
circuit and damage, if ok replace relay.
040 Vehicle Blower - transistor error Remove relay, if fault code 38 is displayed, the relay is defective. Replace relay
041 Water pump - open circuit • Check water pump harness:
042 Water pump - short circuit Check connector B1 – pin 8, (purple) and pin 9, (brown) for continuity, short
circuit and damage.
043 Water pump - transistor error Disconnect connector at water pump, if fault code 041 is displayed, the water pump
is defective. Replace water pump.
047 Fuel pump - short circuit • Check FMP harness:
048 Fuel pump - open circuit Check connector B1 – pin 4, (green) and pin 10, (brown) for continuity, short
circuit and damage.
049 Fuel pump - transistor error Disconnect harness from FMP, if Fault code 048 is displayed the FMP is defective
replace the metering pump.
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
FAULT CODE FAULT DESCRIPTION INFORMATION
DISPLAY
050 ECU locked - too many failed start Too many start attempts, the ECU is locked.
attempts Unlock the ECU, see from pages 32 - 33.
Check fuel quantity and fuel supply, see from page 52. Refer to additional trouble-
shooting at www.espar.com
051 Cool down time out At start-up the flame sensor detects a temperature >70 °C for longer than 240 sec.
• Check exhaust and combustion air system.
• Check flame sensor, see Fault code 064 and 065.
052 Start attempt failed • Check exhaust and combustion air system.
• Check fuel quantity and fuel supply, see from page 52.
• Renew the gauze fuel filter inserted in the connection socket of the metering pump.
053 Flame cutout - Power • Check exhaust and combustion air system.
054 High • Check fuel quantity and fuel supply, see from page 52.
056 Low • Check flame sensor, see Fault code 064 and 065.
057 While in start process
PLEASE NOTE! • Refer to www.wspar.com/help for more troubleshooting tips.
If start attempts are still allowed,
in the event of a flame cutout the
heater restarts, if necessary with
subsequent repeat start.
If the restart or repeated start was
successful, the fault code display
is deleted.
060 Overheat sensor - open circuit • Check overheat sensor:
– Check connector B2 – pin 10, (black) and pin 11, (black) for damage.
– Remove the overheat sensor and check, see page 46.
– If fault code 060 continues to be displayed, Test the ECU.
061 Overheat sensor - open circuit • Check overheat sensor:
– Check connector B2 – pin 10, (black) and pin 11, (black) for damage.
– Remove the overheat sensor and check, see page 46.
– If fault code 061 continues to be displayed, Test the ECU.
062 PCB - open circuit Teste ECU.
063 PCB - short circuit
064 Flame sensor - open circuit • Check flame sensor:
– Check connector B2 – pin 1, (brown) and pin 2, (brown) for damage.
– Remove the flame sensor and check, see page 50.
– If fault code 064 continues to be displayed, test the ECU.
37
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
38
FAULT CODE FAULT DESCRIPTION INFORMATION
DISPLAY
065 Flame sensor - short circuit • Check flame sensor:
– Check connector B2 – pin 1, (brown) and pin 2, (brown) for damage.
– Remove the flame sensor and check, see page 50.
– If fault code 065 continues to be displayed, test the ECU.
069 Communication error • Check diagnostics cable:
– Connector B1 – pin 5 and connector S8 – pin 2, check blue/white wire for
continuity, short circuit and damage, if ok check the components connected to
the diagnostics cable , if ok test the ECU.
071 Surface sensor - open circuit • Check the surface sensor:
– Check connector B2 – pin 7, (black) and pin 8, (black) for damage.
– Remove the surface sensor and check, see page 47.
– If fault code 071 continues to be displayed, test the ECU.
072 Surface sensor - short circuit • Check the surface sensor:
– Check connector B2 – pin 7, (black) and pin 8, (black) for damage.
– Remove the surface sensor and check, see page 47.
– If fault code 72 continues to be displayed, test the ECU.
074 Overheat sensor - out of range • Check overheat sensor:
– Check wiring for continuity, short circuit and damage.
– Check connector B2 – pin 10 (black), and pin 11(black) for damage.
– Remove the overheating sensor and check, see page 46.
– If fault code 74 continues to be displayed, test the ECU.
• Unlock the ECU, see pages 32 - 33.
090
091 Too many resets • Check voltage supply.
092 - 099 • Test ECU.
NOTES:
39
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
40
The permitted repair work to the heater is described in the
"Repair Instructions“ chapter. The heater must be removed from
the vehicle for the repair work to be carried out.
The heater is assembled in the reverse order, note and follow any
additional instructions.
PLEASE NOTE!
After completing all the work and installing the heater in the
vehicle, perform a functional check on the heater.
BEFORE WORKING ON THE HEATER, ALWAYS FOLLOW THE RELEVANT
SAFETY INSTRUCTIONS.
DANGER!
Risk of injury, burns and poisoning!
Always switch off the heater beforehand and leave it to cool.
Disconnect the battery.
The heater must not be operated in closed rooms such as
garages or workshops.
Exception:
Exhaust suction available directly at the entry to the exhaust
pipe.
CAUTION!
The seals of dismantled components must be replaced.
During repair work, check all components for damage and if
necessary replace.
Check connector contacts, plug-in connections and cables for
corrosion and damage and if necessary repair.
Only use original spare parts if replacements are neces-
sary.
After working on the coolant circuit the level of the coolant
must be checked and if necessary topped up according to the
vehicle manufacturer's instructions.
The coolant circuit must then be vented.
Operation or the after running of the heater may only be
stopped in an emergency (see "EMERGENCY SHUT DOWN"
Page 5) by interrupting the battery current (risk of heater
overheating).
SPECIAL TOOL
AMP RELEASE TOOL
The AMP release tool is used to release plug-in contacts in a
connector housing.
This release tool can be ordered directly from AMP.
• For Micro Timer AMP Order No. 0-0539960-1
• For Junior Power Timer AMP Order No. 1-1579007-6
• For standard timer,
Junior timer AMP Order No. 0-0539960-1
7
7
6 7
7
17
16
15
14
19
20
20
2020
7
7
7
7
5
43
2
1
9
10
11
1213
4
8
18
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
ASSEMBLY DRAWING PARTS LIST
1 Jacket with heat exchanger
2 ECU
3 Heater harness with overheat
sensor and surface sensor
4 Screw, M4 x 12 (2x)
5 Cover, ECU
6 Cover, cable, ECU
7 Screw, M4 x 16 (8x)
8 Connecting socket
9 Seal, combustion chamber /
heat exchanger
10 Combustion chamber
11 Seal, combustion chamber /
blower
12 Grommet, fuel pipe
13 Glow pin
14 Flame sensor
15 Grommet, flame sensor
16 Blower
17 Cover, blower
18 Grommet, fuel pipe
19 Cover, electric motor
20 Screw, M5 x 80 (4x)
41
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
42
REPAIR STEPS
PLEASE NOTE!
This repair instruction describes how to dismantle the heater in
individual repair steps. Reference is made to the necessary
preceding steps to be performed at the relevant repair steps.
Repair step 1
Remove “ECU” cover Page 43
Repair step 2
Remove "blower" cover Page 43
Repair step 3
Remove hose fittings from the “ECU” cover Page 44
Repair step 4
Dismantling the “ECU” Page 45
Repair step 5
Remove overheating sensor and surface sensor Page 46
Check overheat sensor Page 46
Check the surface sensor Page 47
Repair step 6
Remove "blower motor" cover and
"Blower assembly with combustion chamber" Page 49
Repair step 7
Measure blower speed Page 49
Repair step 8
Remove flame sensor Page 50
Check flame sensor Page 50
Repair step 9
Check glow plug Page 51
Dismantle glow plug Page 51
CONNECTOR ASSIGNMENT – 10-PIN CONNECTOR S1
CONNECTOR ASSIGNMENT – 14-PIN CONNECTOR B2
Connector housings are shown from the cable inlet side.
Battery ground (-) -brown
Battery plus (+) - red
FMP (+) - green
Vehicle blower - black/red
Add heater signal
Diagnostic wire - blue / white
Water pump (+) - purple
Heater on wire - yellow
FMP (-) - brown / green
Water pump (-) - brown
Flame sensor - brown
Flame sensor - brown
Glow pin - brown
Glow pin - white
Surface sensor - white
Surface sensor - white
Overheat sensor - black
Overheat sensor - white
Blower motor - black
Blower motor - brown
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
DISMANTLE THE HEATER
STEP 1
REMOVE ECU COVER
• Remove 4 screws M4 x 16 (1) from the ECU cover.
• Unlock cover of ECU cable by turning in direction of arrow (A)
pull the ECU cover from the top.
• Keep the ECU cable cover in a safe place for the assembly.
• If an angle connector has been installed, mark the setting.
• Lift ECU cover and carefully pull the water connection socket
out of the jacket.
• Remove ECU cover.
1 Fixing screws M4 x 16
2 ECU cable cover
3 ECU cover
PLEASE NOTE!
Notes for the assembly:
• Before installing the ECU cover, ensure that the toothed rings of
both connection sockets are correctly locked in the cover.
• Insert the ECU cable cover in the ECU cover.
• Screw Torque M4 x 16 = 2.9+0.3 Nm ~ 2.1 ft-lb
STEP 2
REMOVE BLOWER COVER
To dismantle the blower cover, perform Step 1 first.
• Remove 4 M4 x 16 (1) from the blower cover.
• Remove the blower cover, taking care not to damage fuel connection.
1 M4 x 16 screw
2 Fuel pipe
3 Fuel pipe grommet in the blower cover
4 Blower cover
PLEASE NOTE!
NOTES FOR THE ASSEMBLY:
• Replace the fuel grommet in the blower cover.
• Carefully position the blower cover above the fuel connection on the blo-
wer housing, do not clamp the cable between the cover and housing.
• Ensure the fuel connection grommet fits correctly in the blower cover.
• Ensure the blower motor cable grommet fits correctly in the
blower housing.
1 Blower motor cable loom Grommet
• Torque M4 x 16 screws 2.9+0.3 Nm ~ 2.1ft-lb.
43
2
43
11
11
1
1
1
11
53
2
43
11
11
1
1
1
11
53
2
43
11
11
1
1
1
11
53
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
44
STEP 3
REMOVE COOLANT PORTS FROM THE ECU COVER
To dismantle the coolant ports from the ECU cover, perform Step 1
first.
• Push the coolant port down into the ECU cover.
• Loosen toothed ring.
• Remove O-ring.
• Pull the coolant ports from the ECU cover from above.
1 ECU cover
2 Coolant port socket
3 Toothed ring
4 O-ring
PLEASE NOTE!
NOTES FOR THE ASSEMBLY:
• Insert the coolant port in the ECU cover from above.
• Insert O-ring in the groove of the coolant port.
• Fit the toothed ring onto the coolant port and insert in the ring
gear of the ECU cover. If an angled connection socket was fitted,
the angled coolant port must be aligned according to the instal-
lation position or the marking and inserted in the gear ring of
the ECU cover.
2
33
2
1
4 4
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
STEP 4
DISMANTLING THE ECU
To dismantle the ECU, perform Step 1 first.
• Unlock the locking tab at the 14-pin connector (B2) by turning
in direction of arrow (A).
• Pull off the 14-pin connector (B2) from above.
1 14-pin connector (B2)
2 Locking tab
• Undo fixing screw M4 x 12 compression spring overheating
sensor / control box. Remove the compression spring.
1 M4 x 12 screw.
• Undo M4 x 12 screw compression spring surface sensor / ECU.
Remove the compression spring.
1 M4 x 12 screw
• Remove the ECU.
PLEASE NOTE!
The overheat sensor does not have to be removed.
Torque M4 x 12 screws 3.3+0.3 Nm ~ 2.5 ft-lb.
45
1
1
2
A
1
1
1
2
A
11
11
1
2
A
1
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
46
STEP 5
REMOVE OVERHEAT SENSOR AND SURFACE SENSOR
To remove the overheat / Surface sensor, perform Step 1 and
Repair Step 4 first.
• Use long nose pliers to pull the overheat sensor out of the
locator hole in the jacket. Remove overheat / surface sensor
and the 14-pin connector (B2).
1 Overheat sensor
2 Surface sensor
3 14-pin connector (B2)
PLEASE NOTE!
The overheat / surface sensor and 14-pin connector are a sub-
assembly and are not available as individual parts.
• If replacing the overheat / surface sensor and 14-pin connector
(B2) consult page 42. for proper pining.
PLEASE NOTE!
Notes for the assembly:
• When installing, twist the overheating sensor lead harness and
the surface sensor lead harness.
CHECK OVERHEAT SENSOR
• Check the overheat sensor using a digital multimeter in the 14-pin
connector (B2) at pin 10 and 11. If the resistance value lies outside
the diagram or the table of values, replace the overheat sensor.
1 Overheat sensor
2 14-pin connector (B2)
3 Digital multimeter
321
1 2 3
321
321
1 2 3
321
Resis
tance
Temperature (°C)
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
TABLE OF VALUES:
Temp [°C] R [kΩ] Temp[°C] R [kΩ]
0 32.54 ± 2.2 70 1.75 ± 0.13
10 19.87 ± 1.0 80 1.25 ± 0.1
20 12.48 ± 0.5 90 0.91 ± 0.08
30 8.06 ± 0.4 100 0.67 ± 0.06
40 5.33 ± 0.3 110 0.50 ± 0.05
50 3.60 ± 0.25 120 0.38 ± 0.04
60 2.48 ± 0.17
CHECK THE SURFACE SENSOR
• Check the surface sensor using a digital multimeter in the 14-pin
connector (B2) at pin 7 and 8. If the resistance value lies outside
the diagram or the table of values, replace the surface sensor.
1 Surface sensor
2 14-pin connector (B2)
3 Digital multimeter
TABLE OF VALUES
Temp [°C] R [kΩ]
0 30.00 ±1.50
25 10.74 ±0.78
40 6.20 ±0.52
60 3.19 ±0.32
80 1.75 ±0.20
100 1.02 ±0.13
120 0.62 ±0.08
47
321
1 2 3
321
Resis
tance
Temperature (°C)
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
48
STEP 6
REMOVE THE BLOWER MOTOR COVER AND BLOWER SUB-ASSEMBLY
WITH COMBUSTION CHAMBER
To remove the blower motor cover and blower sub-assembly with
combustion chamber, perform Step 1, Step 2 and Step 4 first.
• Remove pins from the blower motor in the 14-pin connector
(B2), pin 13 black and pin 14, brown, using the AMP release tool.
• Remove pin from the flame sensor in the 14-pin connector
(B2), pin 1, brown and pin 2, brown using the AMP release tool.
• Remove pins from the glow pin in the 14-pin connector (B2),
pin 3, brown and pin 6, black using the AMP release tool.
1 14-pin connector (B2)
• Remove 4 x M5 x 80 screws of the blower motor cover and the
blower.
1 M5 x 80 screw.
• Remove blower motor cover.
• Pull the Blower with combustion chamber sub-assembly out of
the heat exchanger.
1 Blower motor cover
2 Blower with combustion chamber sub-assembly
• Remove the combustion chamber from the blower housing, at
the same time pull off the grommet from the glow pin and the
grommet from the fuel tube from the blower housing together
with the combustion chamber.
1 Fuel pipe grommet
2 Glow pin wiring grommet
3 Combustion chamber
4 Blower housing with flame sensor
2
3
1
4
1
2
1
2
3
1
4
2
3
1
4
2
3
1
4
1
1 11
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
REMOVE THE ELECTRIC MOTOR COVER AND BLOWER SUB-ASSEMBLY
WITH COMBUSTION CHAMBER
• Remove seal between the combustion chamber flange and the
blower housing or between the combustion chamber flange and
the heat exchanger, carefully clean all sealing surfaces.
• Pull grommet off the fuel pipe.
CAUTION!
Reusing the dismantled seals and grommets can result in leaks
and malfunctions in the heater.
Use the specified spare parts kit.
1 Grommet, fuel pipe in blower housing
2 Grommet, glow plug in blower housing
3 Seal, combustion chamber flange / blower housing
PLEASE NOTE!
NOTES FOR THE ASSEMBLY:
• Position new seal between the blower housing and combustion
chamber on the combustion chamber flange, note the different
cutouts in the seal.
• Position the glow pin wiring grommet with its flat surface on
the seal (combustion chamber flange).
• Push on the grommet for the fuel pipe and position on the seal
(combustion chamber flange).
• When assembling the combustion chamber and blower housing,
always ensure the grommets sit properly.
• Insert new seal between the combustion chamber and the heat
exchanger, in the circular recess of the jacket and heat exchanger.
• Tightening torque of the fixing screws:
M5 x 80 = 6.5+0.5 Nm ~ 4.8 ft-lb.
STEP 7
MEASURE BLOWER SPEED
To measure the blower speed, perform Repair step 1,2 and 4 first.
• Apply a marking (white paint) to the impeller and measure the
speed using a non-contact r.p.m. counter.
• Apply max. 8.2 V at the 14-pin connector (B2), pin 13 black and
pin 14 brown.
• If the measured speed <10 000 rpm, then replace the blower.
• If the measured speed > 10 000 rpm, then test the ECU.
1 14-pin connector (B2)
2 Marking
49
1
2
1
2
3
1
2
1
2
3
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
50
STEP 8
REMOVE FLAME SENSOR
To remove the flame sensor, perform Repair step 1, Repair step 2
and Repair step 4 and Repair step 6 first.
• Pull the flame sensor wiring loom grommet out of the groove.
• Pull out the flame sensor together with the grommet (graphite
grommet) from the groove in the blower housing.
• Remove the flame sensor.
1 Groove for Flame sensor wiring loom grommet and fuel pipe
grommet
2 Flame sensor wiring loom, semi-round
3 Flame sensor
4 Flame sensor grommet (graphite grommet)
5 Flame sensor collar grommet and graphite grommet
PLEASE NOTE!
NOTES FOR THE INSTALLATION
• The relevant rules of sound engineering practice and any infor-
mation provided by the vehicle manufacturer are to be observed
during the installation and repair.
• When carrying out electric welding on the vehicle, the positive
cable at the battery should be disconnected and placed at
ground to protect the ECU.
CHECK FLAME SENSOR
Check the flame sensor using a digital multimeter. If the resis-
tance value of the flame sensor lies outside the diagram or the
table of values, replace the flame sensor.
1 Flame sensor
2 Digital multimeter
TABLE OF VALUES
Temp [°C] R [Ω] Temp [°C] R [Ω]
0 1000 ±10 200 1758 ±24
50 1194 ±12 250 1941 ±28
100 1385 ±15 300 2120 ±32
150 1573 ±20 350 2297 ±36
12
5
2
3
4
1
12
5
2
3
4
1
Resis
tance
Temperature (°C)
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
STEP 9
CHECK GLOW PIN
To check the glow pin, perform Repair step 1 and 2 first.
• Unlock the locking tab at the 14-pin connector (B2) by turning
in direction of arrow (A).
• Pull off the 14-pin connector (B2) from above.
1 14-pin connector (B2)
2 Locking tab
DISMANTLE GLOW PIN
To remove the glow pin, perform Repair step 1, 2 and 6 first.
• Carefully pull the glow pin out of the combustion chamber and
replace.
1 Glow pin grommet
2 Glow pin
PLEASE NOTE!
NOTES FOR THE ASSEMBLY:
• The following parts are included in the spare parts kit and must
be used:
– Grommet, fuel pipe
– Grommet, fuel pipe in the "blower" cover
– Grommet, flame sensor (graphite grommet)
– Seal, between the combustion chamber flange and the blower
housing
– Seal, between the combustion chamber flange and the heat
exchanger
51
1
2
1
2
A
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
52
MEASURING THE FUEL QUANTITY WITHOUT EDITH
PREPARING FOR THE MEASUREMENT
• Remove the fuel line from the heater and insert a measuring
cylinder (size 25 ml).
• Switch on heater.
• Depending on the heater type, the metering pump starts pumping
fuel after 17 to 20 sec. Ensure that the fuel line is filled with fuel
and free of bubbles. At this point you are ready to perform the test.
• Switch off heater, empty measuring cylinder and insert the fuel
line in to the cylinder.
• Switch on heater.
• Depending on the heater type, the metering pump starts pump-
ing fuel after 17 to 20 sec.
• During the measurement, hold the measuring cylinder at the
level of the heater.
• Gasoline heaters
– For gasoline heaters, because of the delivery rate, it is suffi-
cient to start once to measure the fuel quantity.
• Diesel heaters
– In the case of diesel heaters, after starting once, two auto-
matic start repeats must take place to obtain sufficient fuel
for the measurement.
• After measuring, switch off the heater.
• Read off the quantity of fuel in the measuring cylinder.
6 MAINTENANCE, TROUBLESHOOTING & REPAIRS
EVALUATION
• Compare the measured quantity of fuel with the values in the
following table.
If the measured quantity of fuel is above the maximum value or
below the minimum value, the metering pump must be replaced.
Heater type Hydronic II
Heater version B 5 S D 5 S
Delivery period in sec. 80 sec 129 sec.
(one-off start) (one start + two
repeats)
Fuel quantity – nominal. [ml] 12.4 8.2
Fuel quantity – max. [ml] 13.7 9.0
Fuel quantity – min. [ml] 11.2 7.4
PLEASE NOTE!
Only carry out the fuel measurement if the battery is sufficiently
charged. During the measurement at least 12 volt or max. 13 volt
should be applied to the heater.
FUEL QUANTITY TEST WITH EDITH
• Remove the fuel line at the heater and insert a measuring into
cylinder (size 25 ml).
• Connect heater to EDiTH (ISO adapter) and select "switch on
component" function at the PC.
• Select "metering pump" component, click "Run" button and
pump fuel into the measuring cylinder.
Retain setting of 30 sec. delivery period with 10 Hz metering
pump frequency.
• After 30 sec. the metering pump switches off, empty the mea-
suring cylinder.
MEASUREMENT / EVALUATION
• Switch on the "metering pump" component again via EDiTH and
pump into the measuring cylinder, delivery period 30 sec. with
10 Hz metering pump frequency.
• After 30 sec. the metering pump is switched off, read off the
quantity of fuel in the measuring cylinder.
Heater type Hydronic II
Heater version B 5 S D 5 S
Delivery period in sec. 30
Fuel quantity – nominal. [ml] 8.2 8.9
Fuel quantity – max. [ml] 9.0 9.8
Fuel quantity – min. [ml] 7.7 8.4
Frequency [hz] 10
53
7 PARTS LIST
54
1
152
34
6 5
4
21
20
23 10
109
98
13
13
12
12
1114
2425
19
22
26
26
26
2610
10
10
7
10
10
10
17
1816
HEATER SPARE PARTS DIAGRAM
7 PARTS LIST
SPARE PARTS LISTRef. No. Description Part Number Model #
1 Jacket and heat exchanger See Item 1.1
1.1 Jacket and heat exchanger kitincludes: Item 1, 15, 16, 18, 19, 20 25 2526 01 01 00 • •
2 ECU 22 5206 01 00 01 •22 5206 01 00 02 •
3 Main harness See Item 3.1
3.1 Lead harness kit, heater 25 2526 99 01 21 • •includes: Item 3, 4, 5, 6
4 Screw, M4 x 12 See Item 6.1
5 Compression spring, overheating sensor See Item 6.1
6 Compression spring, surface sensor See Item 6.1
6.1 Compression spring kit 25 2526 99 01 08 • •includes: Item 4, 5, 6
55
20 1
904 0
5
25 2
526 0
5
Gasoline Diesel
7 PARTS LIST
SPARE PARTS LISTRef. No. Description Part Number Model #
7 Cover, ECU See Item 7.17.1 Cover kit, control box 25 2526 05 00 11 • •
includes: Item 7, 8, 9
8 Cover, cable, control box 25 2281 01 00 06 • •9 Ribbed insert See Item 7.110 Screw, M4 x 16 See Item 10.110.1 Screw kit, M4 x 16 (4 screws) 25 2526 99 00 31 • •
includes: Item 10
11 Water pipe socket, straight, di = Ø 20 mm See Item 11.111.1 Water pipe socket kit, straight, di = Ø 20 mm 25 2526 99 01 06 • •
includes: Item 11, 12, 13
12 Toothed ring See Item 14.113 O-ring, 16 x 2 22 1000 70 00 19 • •14 Water pipe socket, 90°, di = Ø 20 mm See Item 14.114.1 Water pipe socket kit, 90°, di = Ø 20 mm 25 2526 80 03 00 • •
includes: Item 12, 13, 14
20 1
904 0
5
25 2
526 0
5
56
7 PARTS LIST
SPARE PARTS LISTRef. No. Description Part Number Model #
15 Seal, combustion chamber flange / hea t exchanger See Item 16.116 Seal, combustion chamber housing / fan See Item 16.116.1 Seal kit 20 1904 99 01 11 •
includes: Item 15, 16 25 2526 99 01 10 •
17 Combustion chamber See Item 17.117.1 Combustion chamber kit 20 1904 10 00 00 •
includes: Item 15, 16, 17, 18, 19, 20 25 2526 10 00 00 •
18 Grommet, fuel pipe See Item 20.119 Grommet, flame sensor See Item 20.120 Grommet, fuel pipe See Item 20.120.1 Grommets kit for combustion chamber, includes: Item 18, 19, 20 25 2526 99 01 04 • •
21 Glow plug See Item 21.121.1 Glow plug kit, includes: Item 15, 16, 18, 19, 20, 21 25 2526 99 01 11 • •
57
20 1
904 0
5
25 2
526 0
5
Gasoline Diesel
Gasoline Diesel
Gasoline Diesel
7 PARTS LIST
SPARE PARTS LISTRef. No. Description Part Number Model#
22 Sensor, flame monitoring See Item 22.122.1 Sensor kit, flame monitoring 25 2526 99 36 00 • •
includes: Item 15, 16, 18, 19, 20, 22
23 Cover, fan, with seal 25 2424 01 03 00 • •24 Fan See Item 24.124.1 Fan kit 25 2526 99 15 00 • •
includes: Item 15, 16, 18, 19, 20, 24
25 Cover, electric motor, complete 25 2424 01 04 00 • •26 Screw, M5 x 80 See Item 26.126.1 Screw kit, M5 x 80 (4 screws)
includes: Item 26 25 2278 01 00 30 • •
20 1
904 0
5
25 2
526 0
5
Gasoline Diesel
Gasoline Diesel
58
8
7
10
15
11
16
11
11 13
3
1
2
12
19
6
14
17
18
7 PARTS LIST
INSTALLATION, WATER AND COMBUSTION AIR SYSTEM
SPARE PARTS DIAGRAM
59
7 PARTS LIST
INSTALLATION, WATER AND COMBUSTION AIR SYSTEMSPARE PARTS LIST Model#
Ref. No. Description Part Number
1 Water pump, 12 V 25 2526 25 00 00 • •
2 Bracket, water pump 22 1000 51 39 00 • •
3 Lead harness, 12 V, L = 2 m 25 2526 80 12 00 • •
4 Hose, water, di = Ø 20 mm 25 1917 80 00 01 • •
5 Hose clip, 20 - 32 mm 10 2067 02 00 32 • •
6 Ring, 21 / 40 22 1000 50 10 02 • •
7 Bracket, heater 22 1000 51 37 00 • •
8 Special screw 25 2526 80 01 01 • •
10 Bracket, straight, L = 180 mm 22 9000 50 93 06 • •
11 Clip 22 1000 50 05 00 • •
12 Air intake 20 mm L= 1000 mm 360 00 099 • •
13 Hose clip, 16 - 25 mm 10 2067 01 60 25 • •
14 Exhaust, Ø 24 mm, L = 1300 mm 360 61 557 • •
15 Exhaust, Ø 24 mm, L = 1000 mm with end sleeve 25 1774 80 02 00 • •
16 Exhaust silencer 22 1000 40 19 00 • •
17 Bracket, exhaust silencer, Z-shape 22 1000 51 35 00 • •
18 Bracket, exhaust silencer, L-shape 22 1000 51 34 00 • •
19 Clip, Ø 28 mm 152 09 010 • •
20 1
904 0
5
25 2
526 0
5
60
8
1
4
2
12
15
18
13
14
7
7
7
6
6
6
3
5
11
6
7
7 PARTS LIST
ELECTRICAL AND FUEL SYSTEM
SPARE PARTS DIAGRAM
61
7 PARTS LIST
ELECTRICS AND FUEL SYSTEMSPARE PARTS LIST Model#
Ref. No. Description Part Number
1 Fuel metering pump, 12 V 22 4517 08 00 00 • •
2 Bracket, fuel metering pump 22 1000 50 04 00 • •
3 Lead harness, fuel metering pump, L = 6 m 25 2526 80 11 00 • •
4 Bracket 20 1348 03 00 02 • •
5 Ø 1.5 mm Fuel line 890 31 118 • •
6 Hose, 3.5 × 3 360 75 400 • •
7 Hose clip, Ø 9 mm 10 2068 00 90 98 • •
8 Ø 2 mm Fuel line (blue) 890 31 054 • •
10 Hose clip, Ø 11 mm 10 2068 01 10 98 • •
11 Tank connection, di = Ø 4 mm 22 1000 20 16 00 • •
12 Cable harness, heater 25 2526 80 10 00 • •
13 Cable harness, fan 22 1000 33 04 00 • •
14 Relay, 12 V 203 00 095 • •
15 Fuse insert, 5 A 204 00 079 • •Fuse insert, 25 A 204 00 089 • •Fuse insert, 20 A 204 00 004 • •
20 1
904 0
5
25 2
526 0
5
62
NOTES:
63
Espar Products, Inc.
(800) 387-4800
(905) 670-0960
(905) 670-0728 Fax
www.espar.com Espar 20
29
00
81
01 1
501.2
014
Su
bje
ct
to c
ha
ng
e w
ith
ou
t n
oti
fica
tion
Top Related