Construct Block Walling
Student Copy
Name ……………………………….
Types of building blocksThe face side of a block usually measures
________ mm x _______ mm
The thickness can vary from 75mm up to 300mm
The weight from 9.9kg to more than 30kg.
Blocks are manufactured to meet __________ ________
standards of between 2.8N/mm² and 7N/mm².
Blocks can be solid, hollow or cellular.
Some blocks have insulating material bonded to one
face or inserted in the voids
Blocks are available in a range of densities.
Blocks that are light in weight are usually less dense
because they are made from an __________ mix.
The ___________ blocks are denser.
Aerated block
Load bearing blocksThese blocks are usually made of Portland cement
and a variety of aggregates. The blocks are precast in
moulds and compacted with the aid of vibration, or in
a moulding machine involving the use of compressed
air, or a combination of both.
Block making machine
Non-load bearing blocksThese blocks are usually made of Portland cement and a
variety of lightweight aggregates; therefore they are not as
dense or as strong as load-bearing blocks.
These blocks are pre-cast in moulds or they can be
produced in slab form and cut to size when set.
Two well known manufacturers are Thermalite and Celcon.Aerated block making
Lightweight BlocksThese blocks are made from lightweight or low density
materials such as _____-____, ______, or lightweight
____________ bonded together with cement.
They are easy to lift and handle and have good thermal
and sound properties
They can absorb water and are be easily broken during
handling and construction.
Lightweight blocks can be cut with a ____________/_______,
a ________ ________ or power saw.
It is good working practice to secure blocks when cutting
with hand or powered tools.
Alternative methods of bonding a
return quoin.
Special blocksMany manufacturers provide special blocks to help bonding and
prevent waste.
These blocks range from coursing blocks to half, quarter and three-
quarter blocks. Other special blocks include return and reveal blocks
which are used to close the cavity at door and window openings.
Special / Coursing BlocksTo maintain bond within a wall it may be necessary to use
either __________ bricks or blocks. These can be cut from a
whole block or special blocks manufactured to those sizes.
These blocks are built into the
walling at junctions and over
openings in the wall. Ordinary
facing or common bricks
should _______ be used for this
purpose.
Plug and screw
This is a common type of fixing specially designed for fixing
to all blocks. It consists of a plastic plug which is driven into
a pre-drilled hole. A screw can then be driven into the
hollow centre of the fixing.
Fixings and finishes
Blockwork below ground level
Trench Blocks
These blocks are bigger in size than normal blocks with a face
dimension size of ______mm x ______mm and are available in
a range of thicknesses ranging from _____mm to _____mm.
One trench block is equivalent in size to 2 aggregate blocks, or
12 bricks, plus wall ties and infill.
Blockwork below ground levelThe following typical details illustrate the proper use
of blocks below DPC level.
DPC
Typical solid foundation in
blockwork
Blocks used below ground level
Blocks are available in a weight less than _____kg with handholds and will
comply with CDM Regulations which cover health and safety issues on site
for repetitive handling.
Solid Blockwork Foundation with an Insulated Cavity Wall
This form of construction incorporates a blockwork
foundation below ground level with a traditional brick and
block cavity wall above. The cavity can be partially filled or
full filled as required.
This type of construction offers a structure with good sound
and thermal insulation qualities.
Solid Blockwork foundation with an insulated cavity wall
Block cavity wall foundation
This is an alternative solid block foundation construction. The blocks below ground level are laid to form a cavity which is then filled up to ground level with a cement / aggregate mix. The cavity can be partially filled or fully filled as required.
Block cavity wall foundation
Apart from the size of the blocks the building operations
used to erect walls are the same as for brickwork.
There are ____ blocks per square metre as opposed to ___
bricks per square metre
Never mix different types of blocks in the same run of walling,
and do not use common or facing bricks as closers as they
will reduce the thermal and sound insulation qualities of the
blockwork.
Always set out the first course ____ so that the position of cut blocks can be
found.
Any adjustment to the width of joints should be made to achieve and maintain a
bond within the wall.
This is called “______ ____________”
Blocks should be laid to a regular bond, usually ______ bond where possible.
Never lay blocks to a bond of less than _____________ bond.
It is not always convenient to build a
junction wall at the same time as the
main wall.
Tee junctions are normally bonded, or
ties can be use with a straight joint.
Indents may be left to allow bonding to
occur at a later stage. Indents are gaps
where blocks will be inserted at a later
date.
Wall ties
Bonded
Junctions to walls
Junctions to wallsThe diagram shows a typical method of constructing
junction walls.
Brick outer leaf Inner leaf walls 100mm
Separating wall 100mmNominal 8mm internal render scratch finish
Partial fill cavity wall 12.5mm gypsum board
mounted on dabs
Tied junction
100mm partition
75mm / 275mm min
Bonding should be set out so that lintels bear preferably
on a whole block. If this is not possible, a minimum two-
thirds length block is acceptable but definitely not less.
(normally by at least 150mm.)
Some types of hollow and cellular blocks may need to be filled
under lintel ends to provide sufficient bearing strength.
_____________________________________________________
_____________________________________________________
_____________________________________________________
_________________________________
In windy weather, the day work lift height may be _________ as an
alternative to propping.
Blocks should be kept dry before use.
Use only specified mortar mixes and ensure that bed and cross
joints are ____________ filled.
Maintain gauge to correspond with brickwork gauge.
Building with blocks is quick and the weight of the blocks could
cause fresh soft mortar bed to be squeezed out. This could
result in collapse / loss of gauge / loss of plumb.
Typical cavity wall construction using facing bricks and blocks
Closing cavities of external walling built with blocks
With all cavity walls it is essential that the cavity be closed at
reveals, such as door and window openings. This can be
achieved by using cut blocks or by using special reveal blocks
manufactured for the purpose.
Cavity wall closersAnother way of sealing the cavity at openings is to use
ready made cavity closers. These are usually made from
tough plastic and internally insulated to prevent cold
bridging. They also have provision for fixing clips to be
attached and built in as the brick / block work proceeds.
For bonding purposes, ________ courses of brickwork are equal
to _________ course of blockwork.
This makes bonding simple as long as both bricks and blocks
are kept accurately ______________.
Section through a solid internal wall
Section through a cavity partition wall
Top Related