1
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start System
2
Model Outline Engine Chassis Body Body Electrical
Variation of Smart Entry & Start SystemDifferent Variations of Main Components
Generation 05CY System 03CY System 00CY System
Application Vehicle
GS430/300, GS450h, IS350/250/220d, AVALON, CAMRY, CAMRY HV, etc.
CROWN PRIUS LS430
Engine Switch Type
Push Type Rotary Type
Power Source
Condition
OFF, E/G Running
OFF
OFF, READY OFF
Engine Switch PositionACC, IG-ON Amber ACC Amber
E/G start is authorized
Green IG-ON Green
Key Insert Not equipped Key Slot Engine Switch
Key
w/ transponder tip w/ transponder tip
Main key only w/ sub key (CROWN)w/o sub key (PRIUS)
w/ sub key
Key Battery: CR1632 Key Battery: CR2032 Low Key Battery
Hold ornament side of key against engine switch
Insert key into key slot Insert key into engine switch
Cancellation Operating cancel procedure Operating cancel switch
Main Control ECU
Certification ECU, ID-Code Box, Steering Lock ECU
Smart ECU,Transponder Key ECU
Theft Deterrent ECU, Steering Lock ECU
3
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start System (G A/T)Overall Memungkinkan mengoperasikan Manual lock/unlock, engine start,
membuka pintu bagasi hanya dengan membawa kunci ( Remote )
[Kunci]
[Back Door Opening (hanya membuka) Function]
[Door Lock / Unlock Function] [Engine Start Function]
4
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemKunci Tombol tiga fungsi, mechanical key dan transponder chip
terdapat pada kunci
Unlock Button
Lock Button
Mechanical KeyMechanical Key
Trunk Button
5
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemLokasi komponen utama
6
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemLokasi komponen utama
7
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemLokasi komponen utama
Front
Fro
nt
Fro
nt
Di bawah bumper belakang
Trunk Oscillator ( inside ) Rear Room Oscillator
Trunk Oscillator ( outside )
Front Room Oscillator Main Body ECU
8
Model Outline Engine Chassis Body Body Electrical
Outside Handle
Smart Entry & Start SystemSystem Diagram
Steering Lock ECU Touch Sensor
Each Door Oscillator
Lock Switch
Room Oscillator (Front)
Trunk OscillatorRoom Oscillator (Rear)Key
Antenna
Antenna
CAN
Tuner
Certification ECU
MDoor Lock / Unlock Motor
ACC RelayIG1 Relay
Engine Switch Transponder Key
Amplifier
ID-code Box
Stop Light Switch
Local Local CommunicationCommunication Neutral Start
Switch
IG2 Relay
EngineECU
Trunk Open SwitchMain Body
ECU
ST Relay
ST CUT Relay
9
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemBasic Operation Actuation area of key
Trunk Oscillator (Outer)
Room Oscillators
Tuner
: Actuation Area (sekitar. 0.7 1.0 m)
Door Oscillator
Key
Trunk Oscillator (Inner)
10
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemDoor Unlock Function
Kunci masuk dalam actuation area
Pemeriksaan ID code
Unlock stand by
Pintu terbuka
Outside Handle
Touch Sensor
Antenna
M Door Lock MotorCAN
Certification ECU
Sentuh touch sensor
Main Body ECU
Key
Tuner
Antenna
Each Door Oscillator
11
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemDoor Lock Function
Pemeriksaan lokasi kunci
(Di luar kendaraan)
Pintu terkunci
Pemeriksaan ID code
Tekan Lock Switch
M Door Lock Motor
Room Oscillators (Front and Rear)
Courtesy Switch
Certification ECU
Outside Handle
Lock Switch
AntennaEach Door Oscillator
Key
Antenna
Main Body ECU
Tuner
CAN
12
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemBack Open Function
Pemeriksaan lokasi kunci
Pintu bagasi terbuka
Pemeriksaan ID code
M Back Door Unlock MotorMain Body
ECU
Room Oscillators (Front and Rear)
AntennaBack Door Oscillator
Key
Certification ECU
AntennaTekan Back Door
Open Switch
Tuner
CAN
Trunk Open Switch
13
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemEngine Start Function
Steering Lock/Immobiliser Cancel
Mesin Hidup
Pemeriksaan lokasi kunci dan ID code
Room Oscillators (Front and Rear)
Key
Antenna
Steering Lock ECU
Serial CommunicationSerial Communication
Certification ECU
Engine Switch
Stop Light Switch IG1 Relay
ACC Relay
Main Body ECU
CAN
Tekan Engine Switch
Tuner
Antenna
Engine ECU
Neutral Start Switch
ID-code Box
ST CUT RelayIG2 Relay
14
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemEngine Start Function Start / stop engine switch control
A/T P range N Range Posisi yang lain
M/T Posisi shift lever bebas M-MT N Range Posisi yang lain
Power Mode
Push engine switch
Setelah satu jam
Push engine switch Push engine switch
Pedal rem tidak
ditekan*
Pedal rem ditekan*
Pedal rem tidak
ditekan
Pedal rem ditekan
Pedal rem tidak
ditekan
Pedal rem ditekan
OFF
ACC
IG-ON
Engine Start
: Dapat dilakukan hanya jika kendaraan berhenti
*: Pedal rem untuk model dengan A/T / M-MTPedal kopling untuk model dengan M/T
15
Model Outline Engine Chassis Body Body Electrical
Power Mode IG-OFF ACC or IG-ON Engine Running
Kondisi mesin hidup*
X X
Kondisi lampu indikator
OFF Green Amber Green OFF
Smart Entry & Start SystemEngine Switch Lampu Indicator mengidentifikasikan mode power saat
ini dan malfungsi sistem
Power Mode Ketika electrical steering lock tidak dapat terbuka ( terkunci )
Malfungsi padaSmart Entry & Start System
Kondisi lampu indikator
Green: Berkedip (1 Hz) Amber: Berkedip (0.5 Hz)
*: Tekan pedal rem (A/T)
16
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemEngine Switch Lampu indikator Green berkedip saat electrical steering lock
tidak dapat terbuka (mesin tidak dapat hidup)
IG-OFF
OFF
ACC
Menyala Green
ACC
Berkedip Green
ACC
Menyala Green
Power Mode
Indicator Light
Mendeteksi electrical steering lock tidak dapat terbuka
Electrical steering lock terbuka atau setelah 15 detik
17
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemEngine Switch Amber indicator light berkedip saat malfungsi terjadi
pada IG1, IG2 relay circuit atau steering lock ECU
IG-ON (Mesin hidup)
OFF
IG-ON (Mesin hidup)
Berkedip Amber
IG-OFF
Berkedip Amber
IG-OFF
OFF
Power Mode
Indicator Light
Mesin tidak dapat hidup kembali
Malfungsi pada IG1, IG2 relay circuit atau steering
lock ECU dideteksiPower mode OFF Setelah 15 detik
18
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemEmergency Start (Saat battery kunci lemah) Tahan logo TOYOTA pada key menghadap engine switch
Beep
Tahan logo TOYOTA pada engine switch
Suara buzzerEngine Start
ACCIG-ON
Selama 5 detik.
Dengan pedal* ditekan
Tanpa pedal* ditekan
dengan pedal* ditekan
*: Pedal rem untuk model dengan A/T / M-MTPedal kopling untuk model dengan M/T
19
Model Outline Engine Chassis Body Body Electrical
Steering Lock ECU
Serial CommunicationSerial Communication
CAN
Smart Entry & Start SystemEmergency Start (Saat battery kunci lemah..)
Steering Lock/Immobiliser Cancel
Mesin hidup
Pemeriksaaan Key ID
Key
Room Oscillators (Front and Rear) Antenna
Certification ECU
Tuner
Antenna
Neutral Start Switch
ID-code Box
Engine ECU
Stop Light Switch IG1 Relay
ACC Relay
ST CUT RelayIG2 Relay
Main Body ECU
file:///mnt/temp/unoconv/20141005115903/20
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemPencegahan kunci tertinggal Saat kunci tertinggal di dalam ruangan, pintu tidak
dapat dikunci
Room Oscillators (Front and Rear)
Outside Handle
Lock Switch
AntennaEach Door Oscillator
Tuner
CAN Main Body ECU
Certification ECU
Wireless Door Lock Buzzer
Click Movie
21
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemMain Body ECU Hold circuit digunakan untuk mencegah power supply
terputus oleh malfungsi pada sirkuit IG1,2 relay
Main Body ECU
IG1 Relay
CPU
Hold
Hold Cancel
IG2 Relay
Hold Circuit
IG1 Relay Drive Circuit
IG2 Relay Drive Circuit
ON
22
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemPre-cautions Memori tidak terhapus saat power source control ECU
power supply terputus
Main Body ECU
Main Body ECU
power supply
terputus Main Body
ECU
EEPROM
ACC Relay
IG1 Relay
Suplai power
IG2 Relay
EEPROM EEPROM
ACC Relay
IG1 Relay
IG2 Relay
Tidak terhapus
ON ON ON ON ON ON
IG-ON IG-ON IG-ON
23
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemSmart Entry & Start System Cancel Function Fungsi ini dapat meng-cancel fungsi fungsi berikut :
Entry Start function, Door lock/unlock function, luggage opening function, prevention of key confinement, warning function dan memory call function
[System Cancel Function]
Cancellation Procedure
1 Unlock sekali dengan tombol UNLOCK*
2 Buka pintu pengemudi
3 Unlock dua kali dengan tombol UNLOCK *
4 Buka dan tutup pintu pengemudi 2 kali (terakhir, terbuka)
5 Unlock dua kali dengan tombol UNLOCK *
6 Buka dan tutup pintu pengemudi sekali (terakhir, terbuka)
7 Tutup pintu pengemudi
Interval
Dalam 5 sec.
Dalam 5 sec.
Dalam 30 sec.
Dalam 30 sec.
Dalam 30 sec.
Dalam 5 sec.
Prasyarat: IG-OFF, Pintu pengemudi ditutup dan diunlock*: Mengoperasikan tombol kunci
24
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemFungsi yang lain Smart Entry & Start
Fungsi sistem yang lain
Parked for a long time
[Battery Saving Function]
Activate
IG-ON
[Fungsi peringatan]
Deactivate
Wireless Door Lock Buzzer
Beep
Warning Light
Perubahan Interval (Setiap 250 ms menjadi 750 ms)
Tidak ada respon lebih dari 5 hariPenonaktifan Tidak ada respon lebih dari 14 hari Berada dalam pendeteksian area lebih dari 10
menit tanpa pengoperasianPengaktifan kembaliOperasikan door lock/unlock tanpa fungsi smart
Passenger
25
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemSteering Lock Function Steering shaft dikunci oleh electric motor
Steering Lock Actuator (dengan Steering Lock
ECU)
26
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemSteering Lock Actuator Steering lock system terdiri dari sebagai berikut :
[Steering Lock Actuator]
Steering Column Tube
Lock Bar
Hall ICs
Gears
Steering Lock ECU
Steering Lock Motor
Lift
Magnet
Model Outline Engine Chassis Body
27
Body Electrical
Smart Entry & Start SystemSystem Diagram
Steering Lock Motor
Hall ICs
Main Body ECU
Steering Lock ECU
Power Supply
Lock Bar Position
Lock/unlock Order
Power Supply for
motor
Certification ECU
ID-code Box
Model Outline Engine Chassis Body
28
Body Electrical
Service Point (Smart Entry & Start System)Basic ServiceCustomize parameterPenggantian Certification ECUPenggantian komponen dan ID Code Registration Kehilangan atau penggantian kunci Penggantian Certification ECU Penggantian ID-code Box Penggantian Steering Lock Actuator Penggantian Engine ECUID Code Registration Key code registration
New key ID registration Additional key ID registration
Key code erasure ECU communication ID registration
file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/29
Model Outline Engine Chassis Body Body Electrical
Service Point (Smart Entry & Start System) Basic Service
Tindakan pencegahan untuk seluruh system Pastikan membawa kunci selama pemeriksaan smart system
Seperti gelombang radio lemah, area pendeteksian bisa berkurang, atau kunci tidak bisa dideteksi dalam situasi sebagai berikut :
1. Batere kunci habis
2. Segala fasilitas yang membangkitkan gelombang radio tinggi seperti menara TV, Pembangkit listrik, Stasiun pemancar, Pom Bensin otomatis, berada didekat area pemeriksaan
3. Peralatan Wireless seperti cellular phone dibawa bersama kunci
4. Kunci terhubung atau ditutupi dengan logam (metal)
5. wireless door lock control yang lain sedang dioperasikan didekat kendaraan
6. Kunci berada di dekat lokasi peralatan yang membangkitkan tegangan tinggi atau noise
Kunci kemungkinan sulit dioperasikan sehubungan dengan bentuk body kendaraan
Kunci kemungkinan tidak dideteksi secara tepat disekitar kaca kendaraan, handle pintu, atau di tengah bumper meskipun saat itu area pendeteksian berada pada bagian luar kendaraan
Kunci kemungkinan tidak dideteksi secara tepat jika berada di instrument panel, rear package tray, floor, atau di dalam glove box meskipun saat itu area pendeteksian berada pada bagian dalam kendaraan
Smart system tidak dapat bekerja pada kondisi sebagai berikut :
1. Smart system sedang di cancel
2. Batere kunci habis / kosong (indicator tidak berkedip saat tombol kunci ditekan)
30
Model Outline Engine Chassis Body Body Electrical
Service Point (Smart Entry & Start System) Basic Service
Bagaimana memulai trouble shooting
1. Kendaraan dibawa ke bengkel
2. Pemeriksaan analisa masalah pelanggan (Sejarah, Kapan, bagaimana, dlll.)
3. Periksa tegangan batere. Jika di bawah 11 V, recharge battery sebelum troubleshoot.
4. Periksa CAN communication system dengan IT II
Jika DTC di output (communication problem) Lanjut ke CAN system
Jika DTC tidak di output (communication problem) Lanjut ke step 5
5. Tabel gejala masalah
Jika gejala terdapat dalam tabel, perbaiki atau ganti
Jika gejala tidak terdapat dalam tabel, lanjut ke langkah 6
6. Analisa secara keseluruhan dan trouble shooting (Untuk lebih lengkap lihat Repair Manual)
Pemeriksaan pada kendaraan
DATA LIST/ACVTIVE TEST
Terminal of ECU
7. Perbaiki atau ganti
8. Tes Konfirmasi
9. Selesai
31
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCase Example Share a key
Key Sharing
New Certification ECU
I want to also take my wifes vehicle with my vehicle key
32
Model Outline Engine Chassis Body Body Electrical
Certification ECU
XVehicle Code
X
Certification ECU
Y
Key ID1 Key ID1
Key ID2
Vehicle Code
Y
Certification ECU
Z
New ECU for IS220d
Key ID2
Vehicle CodeZ
Key ID2
Key ID2
Key ID2
Key ID2
GS430s ECU IS220ds ECU
Smart Entry & Start SystemCase Example Share a key
Vehicle Code is registered into the key in order to check whether a key is registered or not with other certification ECU
Only new Certification ECU without key IDs can overwrite the Vehicle code in the key
X
X Z
New Key
Key ID2
Key ID2
Key ID2 X
GS430s Key
GS430s Key
33
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCase Example Share a key
We can not share two or more vehicles by one key
Key Sharing
34
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCase Example After execute new key ID registration
New Certification ECU
Lost
I found the lost key yesterdayPlease register this key
35
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCase Example Quick depleting of the key battery
Newly bought vehicle LOW KEY BATTERYA month after
Why? Why is the battery depleted in only one month?
36
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemSignal Check (e.g. Drivers Door)
Outside Handle
Touch Sensor
SGT
Lock Switch
Drivers Door Oscillator
ANT1 ANT2 TRG- TRG+
Certification ECUTSW1
SGT ANT1 ANT2 TRG-GND+B
CLG1
CLG CLGB SENS SEL
CG1B SEN1 SEL1
Battery+-
CANLCANH
A
Key
Tuner
RC0 RDA ASELRSSI
+5 DATA ASELRSSIGND
ANT
B
C
D
E
F
G
H
Main Body ECU
Antenna
LF Wave
RF RF WaveWave
37
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCase Example Quick depleting of the key battery
Do not keep the key together with the products emitting electromagnetic waves* otherwise the key battery may deplete quickly
Note that you should always keep such electrical appliances at least 1 m (3 ft.) away from the key
*: Such as a cellular phone, television, personal computer, cellular phone or cordless phone recharger units, electric light stands and fluorescent desk lights) or electrical medical equipment such as low frequency medical appliances.
Oscillators (LF Wave) Electrical Keys (RF Wave)
-A
134.2 kHz
314.00 MHz
-W, -Q, -V 433.92 MHz
China, Hong Kong 315.12 MHz
Ref. Japan 312.25 MHz
LF Wave
RF WaveTelevision
Personal Computer
Cellular Phone
38
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemSignal Check (e.g. Drivers Door)
Symbols(Terminal No.)
Description (Signal) Condition Signal
CLG (10)Permintaan peng aktifan antena
Semua pintu dikunci dan kunci di luar area aktuasi
Kunci berada di area aktuasi
ANT1 (3) Peng aktifan antena
Kunci di luar area aktuasi
Kunci berada di area aktuasi
10 9 8 7 6
5 4 3 2 1
Drivers Door Oscillator Connector
0V
5V
0.3 sec.
0V
5V
3.2 sec.
80 msec.3.2 sec.
0.3 sec.
0V
20V
0V
20V
file:///mnt/temp/unoconv/20141005115903/39
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemSignal Check (e.g. Drivers Door)
Symbols(Terminal No.)
Description (Signal) Condition Signal
SEL (4)Permintaan peng aktifan touch sensor
Kunci di luar area aktuasi
12V
Kunci berada di area aktuasi
SGT (2) Kondisi Touch sensorTidak disentuh 12V
Disentuh 0V
SENS (6)Output kondisi Touch sensor
Outside handle tidak disentuh
12V
Outside handle disentuh
0V
TRG- (9) Kondisi Lock switchLock switch tidak ditekan
Lock switch ditekan 0V
10 9 8 7 6
5 4 3 2 1
Drivers Door Oscillator Connector
0V
12V
3.2 sec.
0V
12V
20 msec.
40
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCase Example System operation glitch by disturbance electric wave
My vehicle sometimes does not work properly
41
Model Outline Engine Chassis Body Body Electrical
Service Point (Smart Entry & Start System) Customize parameter
Saat customer meminta perubahan fungsi, pastikan bahwa fungsi tersebut dapat di customized Buat catatan untuk current setting sebelum melakuakan customize Saat trouble shooting suatu fungsi, pertama pastikan bahwa fungsi di set ke default setting.
Tampilan (Item) Default Fungsi Setting
Ignition available area (Entry ignition available area)
ALLFunction to choose the available
area for electrical key to start E/G and cancel the steering lock
FRONT / ALL
Park Wait Time (waiting time to
permit opening door after locking)
2.5 sFunction that sets waiting time to permit opening door after door is locked with entry lock function
0.5s/1.5s/2.5s/5.0s
Trunk open mode (luggage
compartment opening operation)
ON
Function to open luggage compartment when driver has the
electrical key and presses the luggage open button
ON / OFF
Key Low Battery Warning (warn when key battery becomes
weak)
ONFunction to set a warning function for the time when a key battery
becomes weakON / OFF
Model Outline Engine Chassis Body
42
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus semua Kunci hilang atau penggantian
Kunci
NOTE:Jika semua kunci tidak diregister selama registrasi kunci yang lain, kunci tersebut tidak dapat diregistrasi kemudian saat penggantian Certification ECU
*: Perlu penggantian, walaupun Certification ECU dan ID-code Box dalam kondisi normal
Jumlah Kunci
Condition before registration
Sedikitnya 1 Kunci
tersedia
1. Menggunakan Kunci tersisa, hapus kode kunci yang hilang [Key Code Erasure]2. Register kunci tambahan jika diperlukan [Key Code Registration] (Additional key ID registration)
Semua Kunci hilang
1. Ganti ID-code box dan Certification ECU*2. Register semua Kunci [Key Code Registration] (New key ID registration)3. Register ID-code Box Engine ECU communication ID [ECU ECM Communication ID Registration]
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
43
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Penjelasan S Code
S code dihasilkan oleh semua key ID yang diregistrasi dan didaftarkan (register) ke Certification ECU dan ID-code Box
Certification ECU
S Code
Key ID1
Key ID2
Key ID3
ID-code Box
S Code
Key ID1
Key ID2
Key ID3
Certification ECU
S Code
Key ID1
Key ID2
ID-code Box
S Code
Key ID1
Key ID2
Key ID3
Cannot register
Same S code
Not same S code
Key ID1
Key ID2
Key ID3
Key ID1
Key ID2
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
44
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration DAlam kasus penggantian Kunci
Perlu untuk meregister S code baru ke Certification ECU dan ID-code Box dengan kunci tersisa
Certification ECU
S Code
Key ID1
Key ID2
Key ID3
Certification ECU
ID-code Box
S Code
Key ID1
Key ID2
Key ID3
ID-code Box
Same S code
Same S code
Hapus kode Key ID2, 3
Tambahkan kode Key ID2, 4
Key ID1
Key ID2
Key ID3(Malfunction)
S Code
Key ID1
Key ID2
Key ID4
S Code
Key ID1
Key ID2
Key ID4
Key ID1
Key ID2
Key ID4(Baru)
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
45
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus semua kunci hilang
Perlu untuk mengganti kedua ECU, karena S code yang ada tidak dapat di daftarkan (diregister)
Certification ECU
S Code
Key ID1
Key ID2
Key ID3
Certification ECU
ID-code Box
S Code
Key ID1
Key ID2
Key ID3
ID-code Box
Same S code
Ganti kedua ECU
Register kunci baru
Key ID1(hilang)
Key ID2(hilang)
Key ID3(hilang)
S Code
Key ID4
Key ID5
Key ID6
S Code
Key ID4
Key ID5
Key ID6
ECU baruECU baru
S code tidak dapat diregister
Key ID4(Baru)
Key ID5(Baru )
Key ID6(Baru)
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
46
Body Electrical
Certification ECU
XVehicle Code
X
Certification ECU
Y
Key ID1 Key ID3
Key ID4
Vehicle Code
Y
X
Certification ECU
Z
ECU baru
Key ID5
Vehicle Code
Z
X Z
New Key
Key ID2
Key ID2
Key ID2
Key ID5Key ID5
Key ID4
Key ID4 X
ECU terpasang ECU terpasang
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Penjelasan kode kendaraan ( ECU ) di dalam kunci
Kode kendaraan di daftarkan ke dalam kunci, bertutuan untuk memeriksa apakah kunci diregister atau tidak dengan certification ECU yang lain
Hanya Certification ECU baru tanpa ID yang dapat menulis ulang kode kendaraan dalam kunci
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
47
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus penggantian Certification ECU
Jumlah kunci
Condition before registration
Key ID codes can beregistered / erased
Key ID codes cannot be either registered / erased
Semua kunci terpasang
1. Ganti certification ECU2. Register semua kunci [Key Code Registration] (New key ID registration)
Beberapa kunci hilang
1. Hapus kode kunci [Key Code Erasure] 2. Register kunci tersisa [Key Code Registration] (Additional key ID registration)3. Ganti certification ECU4. Register semua kunci[Key Code Registration]
(New key ID registration)
1. Ganti certification ECU dan ID-code box*2. Register semua kunci [Key Code Registration]
(New key ID registration)3. Register ID-code Box engine ECU communication ID
[ECU ECM Communication ID Registration]
Catatan:Jika beberapa kunci tidak diregister selama meregistrasi kunci yang lain, kunci tersebut tidak dapat diregistrasi kemudian
*: Perlu penggantian, meskipun ID-code box dalam kondisi normal
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
48
Body Electrical
Service Point (Smart Entry & Start System)Penggantian Certification ECU Hanya mengganti circuit board, oleh karena itu diperlukan
pencegahan kesalahan penanganan terhadap listrik static
Certification ECU Case
Circuit Board
Antistatic Bag untuk melepas
Supply Parts(89990-)
Antistatic Bag untuk memasang(dalam Circuit Board baru)
ECU CoverAntistatic Bag
Instruksi penanganan
Circuit Board baru
Replacement of Certification
ECUOnly replace the circuit
board, therefore static
electricity prevention
countermeasure is required
Model Outline Engine Chassis Body
49
Body Electrical
Service Point (Smart Entry & Start System)Penggantian Certification ECU Procedure penggantian
1.Lepas Certification ECU2.Lepas ECU cover
ECU Cover(non-reusable part)
3.Tutup tangan dengan antistatic bag, Lalu lepas circuit board
Antistatic Bag
4.Tutup circuit board yang dilepas dengan antistatic bag
Penting: Jangan menyentuh element atau soldered part tanpa antistatic bag,untuk mencegah kerusakan oleh listrik static
Catatan:Saat mengembalikan circuit board yang dilepas, taruh ke dalam antistatic bag yang disediakan dan masukkan ke dalam box
Model Outline Engine Chassis Body
50
Body Electrical
Service Point (Smart Entry & Start System)Penggantian Certification ECU Procedure penggantian
5.Putar antistatic bag pada circuit board baru
6.pasang circuit board baru sepanjang guide rail
Guide Rail
7. Pasang ECU cover baru8. Pasang Certification ECU
Model Outline Engine Chassis Body
51
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus penggantian Certification ECU (Beberapa kunci
hilang) Perlu untuk meregister kode S baru ke Certification ECU dan
ID-code Box dengan kunci yang tersisa
Certification ECU
S Code
Key ID1
Key ID2
Key ID3
Certification ECU
S Code
Key ID1
Key ID2
ID-code Box
S Code
Key ID1
Key ID2
Key ID3
ID-code Box
S Code
Key ID1
Key ID2
Same S code
Same S code
Hapus kode kunci ID2, 3
Tambahkan kode kunci ID2
Current ECU
Ganti Certification ECU setelah prosedur tersebut
Key ID1
Key ID2
Key ID3(Hilang)
Key ID1
Key ID2
Current ECU
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
52
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus penggantian Certification ECU (Beberapa kunci
hilang) Ganti Certification ECU dan ID-code Box, jika fungsi registrasi
tidak bekerja
Certification ECU
ID-code Box
Certification ECU
S Code
Key ID1
Key ID2
Key ID3
ID-code Box
S Code
Key ID1
Key ID2
Key ID3
Fungsi registrasi tidak bekerja
S Code
Key ID1
Key ID2
S Code
Key ID1
Key ID2
Current ECU
Ganti kedua ECU
S code tidak dapat diregistrasi
New ECUNew ECU
Key ID1
Key ID2
Key ID3(hilang)
Key ID1
Key ID2
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
53
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus penggantian ID-code box
Jumlah kunci
Kondisi sebelum registrasi
Setidaknya tersedia 1
kunci
1. Ganti ID-code box2. Register recognition kode di dalam ECU
[Key code registration]3. Register ID-code Box Engine ECU communication ID
[ECU ECM Communication ID Registration]
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
54
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus penggantian Steering Lock Actuator
Jumlah kunci
Kondisi sebelum registrasi
Setidaknya tersedia 1
kunci
1. Ganti Steering Lock Actuator2. Register recognition kode di dalam ECUs
[ECU Communication ID Registration]
Catatan:Dalam kondisi berikut mesin tidak dapat hidup untuk pertama kali (dikarenakan Steering Lock ECU tidak dapat secara tepat mendeteksi posisi steering lock bar)[Steering lock ECU baru belum menyimpan posisi steering lock bar] Setelah mengganti Steering Lock Actuator Setelah mengisi/mengganti battery yang kosong
Buka dan tutup pintu pengemudi untuk menghidupkan mesin
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
55
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Dalam kasus penggantian engine ECU
Jumlah kunci
Kondisi sebelum registrasi
Setidaknya tersedia 1
kunci
1. Ganti Engine ECU2. Register ID-code Box Engine ECU communication ID
[ECU ECM Communication ID Registration]
Catatan:Jangan mengoperasikan switch power mode ON/OFF lebih dari 20 kali sebelum menyelesaikan ECU ECM Communication ID Registration jika tidak ganti Engine ECU
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
56
Body Electrical
ID-code Box
G Code
S Code
L Code
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Penjelasan S Code, G Code dan L Code
Steering Lock ECU
L Code
Engine ECU
G Code
KeyCertification ECU
S Code
Key ID1
Key ID2
Key Code Registration New Key ID Additional Key ID Key ID erasure
ECU-ECM Communication ID Registration
ID-code Box atau Engine ECU diganti
ECU Communication ID Registration
Jika hanya Steering Lock ECU atau ID-code Box diganti
ECU Communication ID Registration (Automatically)
Certification ECU dan ID-code diganti
ECU Communication ID Registration (Automatically)
Jika hanya ID-code Box diganti
: Automatically: Manually (Tester): Manually (SST)
Key ID#
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
57
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code RegistrationECU
ECM Communication ID Registration
CG
Tc
1. Menggunakan SST, hubungkan terminals Tc dan CG pada DLC3
2. Putar power switch ON (jangan menghidupkan mesin) dan biarkan selama 30 menit.
3. Putar power switch OFF dan lepas terminals Tc dan CG.
4. Periksa bahwa mesin dapat hidup
file:///mnt/temp/unoconv/20141005115903/file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
58
Body Electrical
Service Point (Smart Entry & Start System)Penggantian komponen dan ID Code Registration Catatan untuk ID code registration
Power Mode tidak dapat diputar ON (IG-ON) lebih dari 10 kali saat penggantian certification ECU.
Bagaimanapun, ID code registration dapat dilanjutkan dengan Intelligent tester II saat Ignition diputar ON sambil mengoperasikan drivers door courtesy switch ON/OFF terus menerus pada interval 1.5 detik atau kurang
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
59
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Using intelligent tester II
Key Code Registration (New key ID registration)
Tidak ada kunci yang terdaftar di ID-code box
Semua kunci tersedia (Satu kunci atau lebih terdaftar
di dalam ID-code Box)
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
60
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Registration (New key ID registration)
To register another key code
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
61
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Registration (New key ID registration)
[5]
[2]
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
62
Body Electrical
[5]
[2]
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Registration (Additional key ID registration)
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
63
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Registration (Additional key ID registration)
To register another key code
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
64
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Registration (Additional key ID registration)
[4]
[3]
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
65
Body Electrical
[3]
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Erasure (Erase all registered key except one)
file:///mnt/temp/unoconv/20141005115903/Model Outline Engine Chassis Body
66
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
Key Code Erasure (Erase all registered key except one)
Model Outline Engine Chassis Body
67
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Menggunakan intelligent tester II
ECU Communication ID Registration
68
Model Outline Engine Chassis Body Body Electrical
Smart Entry & Start SystemCommunication Check (Key Diag Mode) Each oscillator can be checked by activating specified
oscillator Buzzer sounds when the key is detected in activated
actuation area
Model Outline Engine Chassis Body
69
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Manual operation (only for Indonesia model)
Manual registration standby modeOperation Interval
Initial Condition Drivers door is closed Power Mode is IG-OFF
1 Open drivers door 2 Lock / unlock door twice by manual door lock switch 10 sec.
3 I. Close / open drivers door twiceII. Lock / unlock door once
40 sec.
4 I. Close drivers doorII. Lock / unlock door once
20 sec.
5 I. Open drivers doorII. Lock / unlock door once
20 sec.
6 I. Close / open drivers door twiceII. Close drivers door (all doors close)
40 sec.
New Key ID Registration
Additional Key ID Registration
Key ID Erasure
ECU Communication ID Registration
Key Confirmation
Model Outline Engine Chassis Body
70
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Manual operation (only for Indonesia model)
Key Code Registration (New key ID registration)Operation Interval
Initial Condition In manual registration standby mode Keys are not registered to certification ECU
Number of registered key in ID-code box
No registered One or more registered
1 Touch engine switch with all registered keys one by one
40 sec.
2 Touch engine switch with a key to be registered 3 Set key on front passenger seat
4 Repeat steps (2 and 3) by an increment of a key to be registered
5 Open drivers door
NOTE:- Make sure the emblem side of the key is facing the engine switch, when the key touched
engine switch- When registering several keys, only have one key in the cabin at a time. If several keys
are in the cabin at the same time, the waves of keys will interfere with each other and key registration cannot be performed properly
Model Outline Engine Chassis Body
71
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Manual operation (only for Indonesia model)
Key Code Registration (Additional key ID registration)Operation Interval
Initial Condition In manual registration standby mode One or more keys are registered to certification ECU
1 I. Change power mode to ON/OFF onceII. Open/close drivers door once
40 sec.
2 Touch engine switch with registered key 40 sec.
3 Touch engine switch with key to be registered 4 Set key on front passenger seat
5 Repeat steps (3 and 4) by an increment of a key to be registered
6 Open drivers door
NOTE:- Make sure the emblem side of the key is facing the engine switch, when the key touched
engine switch- When registering several keys, only have one key in the cabin at a time. If several keys
are in the cabin at the same time, the waves of keys will interfere with each other and key registration cannot be performed properly
Model Outline Engine Chassis Body
72
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Manual operation (only for Indonesia model)
Key Code Erasure (Erase all registered key except one)Operation Interval
Initial Condition In manual registration standby mode One or more keys are registered to certification ECU
1 I. Change power mode to ON / OFF 5 timesII. Open/close drivers door once
40 sec.
2 Touch engine switch with registered key to keep 40 sec.
NOTE:- Make sure the emblem side of the key is facing the engine switch, when the key touched
engine switch
Model Outline Engine Chassis Body
73
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Manual operation (only for Indonesia model)
ECU Communication ID RegistrationOperation Interval
Initial Condition In manual registration standby mode One or more keys are registered to certification ECU
1 I. Change power mode to ON / OFF 2 timesII. Open/close drivers door once
40 sec.
2 Touch engine switch with registered key 40 sec.
NOTE:- Make sure the emblem side of the key is facing the engine switch, when the key touched
engine switch
Model Outline Engine Chassis Body
74
Body Electrical
Service Point (Smart Entry & Start System)ID Code Registration Manual operation (only for Indonesia model)
Key confirmationOperation Interval
Initial Condition In manual registration standby mode One or more keys are registered to certification ECU
1 I. Change power mode to ON / OFF 3 timesII. Open/close drivers door once
40 sec.
[Number of registered key]ex.) When 3 keys are registering
Wireless Door Lock Buzzer
OFF
ON
1 2 3
75
Model Outline Engine Chassis Body Body Electrical
file:///mnt/temp/unoconv/20141005115903/Top Related