Additional wireless power monitor, single phase
Additional wireless power monitor, single phase
EN-P
USER GUIDE
Version 1.0
For further details, please contact:
Enistic Limited, 4 Isis Business Centre, Pony Road, Oxford, OX4 2RD
© Copyright 2014 Enistic Limited.
www.enistic.com Page 1
Additional wireless power monitor, single phase
CONTENTS
Overview...............................................................................................................................................3
Hardware architecture..........................................................................................................................3
Wiring Guide..........................................................................................................................................3
Pairing Transmitter With a Ethernet Receiver – Photograph.................................................................3
Battery Replacement.............................................................................................................................3
Current Transformer Connection – Photograph....................................................................................3
Current Transformers Dimension..........................................................................................................3
Specifications.........................................................................................................................................3
DOCUMENT HISTORY
Version Date Author Notes
1.0 19 Jan 2015 Wasil Ali Preliminary release of alpha test details.
www.enistic.com Page 2
Additional wireless power monitor, single phase
OVERVIEW
Additional wireless power monitor, single phase (EN-P) is a meter that reads data from current clamps and sends back to the Ethernet wireless receiver (EN112). It is a low cost solution and suitable for office and industrial monitoring applications. EN-P has one input to attach Current Sensor (CT5 – CT3000) supporting readings from devices up to 3000A. It communicates with the controller through the Wireless communications (RF 433MHz ISM band). It comes in a small enclosure and can be mounted on a wall. Simple to Install and easy to configure.
• Suitable for residential, commercial and industrial monitoring purposes.
• Manufactured to comply with IEC 60687/61036/61268 and IEC 62053-21/62053-22/62053-23.
• Single receiver can handle multiple transmitters.
• Plug and play. Easy to install on site.
• Wireless, low power operation.
FEATURES
• Highly accurate design
• Manufactured to comply with international standards IEC 60687/61036/61268 and IEC 62053-21/62053-22/62053-23
• Connects with controller on 433 MHz Band
• Encrypted communications for secure operation
• Good range
ORDER CODES
EN-P - Additional wireless power monitor, single phase
EN126 - Battery 3.6V, AA, 2600mAh
Split core current sensor sizes for EN-P with order code in bold:
EN114 - CT5, EN115 - CT10, EN116 - CT15, EN117 - CT30,
EN118 - CT60, EN119 - CT100, EN120 - CT200, EN121 - CT400,
EN122 - CT600, EN123 - CT1500, EN124 - CT3000
www.enistic.com Page 3
Additional wireless power monitor, single phase
HARDWARE ARCHITECTURE
Figure 1: Hardware Architecture
Wireless power monitor, single phase is built of a processor and RF transceiver to communicate with
the controller. This device is responsible for taking the readings from Current Clamps and send
readings to the controller via RF link. Frequency off the link is 433MHz. It transmits reading to the
receiver (EN112) every 5 minutes
www.enistic.com Page 4
Additional wireless power monitor, single phase
WIRING GUIDE
Figure 2: Activity LED “Green”
Figure 3: Current Transformer Connection
Figure 4: Non-Rechargeable Battery
www.enistic.com Page 5
EN-P
Additional wireless power monitor, single phase
PAIRING TRANSMITTER WITH A ETHERNET RECEIVER – PHOTOGRAPH
In order to pair each transmitter (EN-P) with the receiver (EN112) press the pairing mode button at
the back of the receiver (EN112). During pairing mode the radio activity and server activity LEDs start
flashing for about one minute. While receiver is in pairing mode connect the battery in the
transmitter and wait so that it pairs with the receiver. Once it pairs you will see the radio activity and
server activity LEDs stop flashing.
You need to repeat the above step each time if you have multiple transmitters (EN-P).
Figure 5: Ethernet Receiver Connection Layout
www.enistic.com Page 6
EN112
Additional wireless power monitor, single phase
BATTERY REPLACEMENT
Figure 6: Battery Replacement
BATTERY DETAILS Nominal Voltage 3.6V
Nominal Capacity 2.6 Ah (2600mAh)
Nominal Current 2mA
Maximum Continuous Discharge Current 70mA
Battery Weight 17g
Temperature Range –60°C ...+85 °C
Diameter 14.65mm
Length 50.3mm
Order Code: EN126
www.enistic.com Page 8
EN126
Additional wireless power monitor, single phase
CURRENT TRANSFORMER CONNECTION – PHOTOGRAPH
Figure 7: Current Transformer
Figure 8: Current Transformer Connection
www.enistic.com Page 9
Additional wireless power monitor, single phase
CURRENT TRANSFORMERS DIMENSION
www.enistic.com Page 10
Additional wireless power monitor, single phase
SPECIFICATIONS
ElectricalItem Value UnitBattery for EN-P 3.6 Vdc
Battery Type Lithium Thionyl ChlorideBattery Capacity 2600 mAhPower Consumption (Typical / Maximum)
9 / 250 mW
PhysicalItem Value UnitSize (l x w x h) 110x71x42 mmFitting Wall mountStorage temperature (min -> max) -10 -> +30 °COperation temperature (min -> max) -10 –> 85 °C
Measurements and MetrologyItem Value UnitChannels 1Nominal Current 5-3000* AMin. Current 0* AMin. Current 1% ** 0.05-150* AMax. Current 5-3150* AMax. Current 1% ** 4.95-2850* AProbe Cable Length 1000-1500* mmCommunicationItem Value UnitStandard RF -Frequency 433 MHzMaximum Range between Tx and Rx (LOS) 100 m
Encryption Yes
Miscellaneous and StandardsItem Value UnitCountry of Design / Manufacture UKPackaging Cardboard box
www.enistic.com Page 11
Top Related