© 2020 Signature Kitchen Suite. All rights reserved. Design, features and specifications are subject to change without notice. Specifications are for planning purposes only. Consult the product’s installation instructions for final dimensional data and other details prior to making cutouts or custom panels. Consult with a heating and ventilation engineer for your specific ventilation requirements. Non-metric weights and measurements are approximate. Smart features require Internet access. 1-855-790-6655 | www.signaturekitchensuite.com
SKSMD2401SMICROWAVE OVEN DRAWER
1.2 CU. FT. OVEN CAPACITY1.2 cu. ft. capacity is designed to provide plenty of room to heat large items like casserole dishes and dinner platters.
EASY TOUCH AUTOMATIC DRAWERThe Easy Touch Automatic Drawer system eases open with a gentle pull or the touch of a button. Give the drawer a small nudge and it smoothly shuts for you. The even, gliding action and solid construction prevents liquids from spilling during opening and closing.
SMOOTHTOUCH™ GLASS CONTROLSIntuitive SmoothTouch™ Glass Controls not only look sleek but make operating the microwave drawer easy with just a touch. The seamless controls are also easy to wipe clean.
INSTALLATION FLEXIBILITYFlexible installation options include below an island or peninsula and in standard cabinetry. A heat deflector kit is included for flush or true flush installation for an integrated, streamlined look.
FeaturesCapacity 1.2 cu. ft.Power Output 900 WSensor Cooking YesDrawer Opening Easy Touch
AutomaticLighting Incandescent
Cooking MenuDisplay Type SmoothTouch™
Glass TouchPower Levels 11Sensor Touch Cooking / Reheat Options
12 (Baked Potatoes, Sweet Potatoes, Fish / Seafood, Brown Rice, White Rice, Quick Fresh Vegetables, Longer Fresh Vegetables, Steamer Bag, Frozen Vegetables, Ground Meat, Frozen, Beverage Reheat
Defrost Options 6 (Ground Meat, Steaks/Chops, Boneless Poultry, Bone-in Poultry, Roast, Casserole/Soup)
Minute Plus™ YesStop/Clear, Start/Enter YesCompletion Beeper YesEnergy Saving Mode Yes (Dims Display
After 3 Minutes of Inactivity)
Kitchen Timer/Clock YesChild Safety Lock Yes
Page 1 of 6 | Effective 6/20 | WCAG
SKSMD2401SMICROWAVE OVEN DRAWER
Installation FeaturesDeflector Vent Kit Included (Required for Flush and True Flush Installation)
Yes
Technical SpecsRequired Power Supply 120V, 60Hz /
15 AmpPlug Type 3-ProngPower Cord Length (inches) 48
Dimensions and WeightOverall Exterior Width (inches) 23 7/8Overall Exterior Height (inches) 15 15/16 Overall Exterior Depth (inches) 23 1/64Required Cutout Width (inches) 22 1/8Required Cutout Height (inches) 15 9/16Required Cutout Depth (inches) 23 1/2Interior Width (inches) 17 5/16Interior Height (inches) 7 1/8Interior Depth (inches) 16 9/16Net Weight (approx.) 74 lbsShipping Weight (approx.) 88 lbs
Warranty Summary*Limited Warranty, Parts & Labor (In Home Service)
2 Year
Limited Warranty on Magnetron (In Home Service)
10 Years
Additional 1 Year When Product Registration is Completed Online
Yes
*These warranties give you specific legal rights and you may have other rights that vary from state to state. For complete warranty details, refer to your Use & Care manual.
Page 2 of 6 | Effective 6/20 | WCAG
OVERALL PRODUCT DIMENSIONS
MOUNTING SCREW LOCATIONS
1 5/16" (33 mm)Door Thickness
15" (381 mm)Auto Drawer
Opening
4 11/16" (119 mm)
1 3/4" (44 mm)
4" (102 mm)
21 5/8"(549 mm)
14 19/32"(371 mm)
21 7/8" (556 mm)
23 7/8"(606 mm)
15 15/16"(405 mm)
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Suggested electricaloutlet location*
6" (152 mm)
5" (127 mm)
4" (101 mm)
3 1/2" (89 mm)
15 9/16"(395 mm)
36" (914 mm)Countertop
Height
24" (914 mm)Cabinet Minimum
23 1/2"(597 mm)Minimum
Depth
B
D
C
A
A
22 1/8"(562 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
C - Allow 7/16" (11 mm) minimum space
A - Allow 7/8" (22 mm) overlapB - Allow 3/16" (5 mm) overlap
D - Allow 1/8" (3 mm) overlap
Standard (Proud) InstallationOverall Product Dimensions
Mounting Screw Location
Flush Installation
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Anti-Tip BlockSuggested electrical
outlet location*
4"(101 mm)
3 1/2" (89 mm)
6" (152 mm)
23 1/2" (597 mm)Minimum Depth
16 15/16" (430 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
5" (127 mm)
24 3/16" (614 mm) Minimum24 1/2" (622 mm) Maximum
1 1/16" (27 mm)
1 3/4" (44 mm)
22 1/8"(562 mm)
1 3/4"(44 mm)
Note: the face of theshelf must sit 1 3/4"
(44.4 mm) back fromthe face of the cabinet.
Shelfface Cabinet face
Note: the mounting surface of thefinished cleat must sit 1 1/16" (27 mm)back from the face of the cabinet (pushingthe face of the drawer out 1/4" (6 mm))
Anti-Tip Block
Cabinet face
Drawerface
Mountingcleat
Top view
22 1/8"(562 mm)
Mounting cleatopening width
CL
True Flush Installation
16 7/8"(429 mm)
Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet.
Top viewCL
Cabinet face
Drawerface
Mountingcleat
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
22 1/8"(562 mm)
Mounting cleatopening width
MountingFlange
Flush Installation Deflector Vent
Side View
FrontFace ofCabinet
16 15/16"(430 mm)
FlushOpeningHeight
3/4" (19 mm)Shelf
1 3/4" (44 mm)Front Face of Shelf
Anti-Tip Block
No Oven
Front View
SuggestedElectrical
OutletLocation
Anti-Tip Block
3/4" (19 mm)Shelf
22 1/8" (562 mm)Mounting Cleat Opening Width
24 3/16" (614 mm) Min24 1/2" (622 mm) MaxFlush Opening Width
Shelf detail showing the deflector vent installed.Shelf detail showing the deflector ventduring installation.
Position deflector vent and mark holes.Pre drill using a 1/16" (1.57 mm) bit before mounting.
1 5/16" (33 mm)Door Thickness
15" (381 mm)Auto Drawer
Opening
4 11/16" (119 mm)
1 3/4" (44 mm)
4" (102 mm)
21 5/8"(549 mm)
14 19/32"(371 mm)
21 7/8" (556 mm)
23 7/8"(606 mm)
15 15/16"(405 mm)
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Suggested electricaloutlet location*
6" (152 mm)
5" (127 mm)
4" (101 mm)
3 1/2" (89 mm)
15 9/16"(395 mm)
36" (914 mm)Countertop
Height
24" (914 mm)Cabinet Minimum
23 1/2"(597 mm)Minimum
Depth
B
D
C
A
A
22 1/8"(562 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
C - Allow 7/16" (11 mm) minimum space
A - Allow 7/8" (22 mm) overlapB - Allow 3/16" (5 mm) overlap
D - Allow 1/8" (3 mm) overlap
Standard (Proud) InstallationOverall Product Dimensions
Mounting Screw Location
Flush Installation
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Anti-Tip BlockSuggested electrical
outlet location*
4"(101 mm)
3 1/2" (89 mm)
6" (152 mm)
23 1/2" (597 mm)Minimum Depth
16 15/16" (430 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
5" (127 mm)
24 3/16" (614 mm) Minimum24 1/2" (622 mm) Maximum
1 1/16" (27 mm)
1 3/4" (44 mm)
22 1/8"(562 mm)
1 3/4"(44 mm)
Note: the face of theshelf must sit 1 3/4"
(44.4 mm) back fromthe face of the cabinet.
Shelfface Cabinet face
Note: the mounting surface of thefinished cleat must sit 1 1/16" (27 mm)back from the face of the cabinet (pushingthe face of the drawer out 1/4" (6 mm))
Anti-Tip Block
Cabinet face
Drawerface
Mountingcleat
Top view
22 1/8"(562 mm)
Mounting cleatopening width
CL
True Flush Installation
16 7/8"(429 mm)
Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet.
Top viewCL
Cabinet face
Drawerface
Mountingcleat
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
22 1/8"(562 mm)
Mounting cleatopening width
MountingFlange
Flush Installation Deflector Vent
Side View
FrontFace ofCabinet
16 15/16"(430 mm)
FlushOpeningHeight
3/4" (19 mm)Shelf
1 3/4" (44 mm)Front Face of Shelf
Anti-Tip Block
No Oven
Front View
SuggestedElectrical
OutletLocation
Anti-Tip Block
3/4" (19 mm)Shelf
22 1/8" (562 mm)Mounting Cleat Opening Width
24 3/16" (614 mm) Min24 1/2" (622 mm) MaxFlush Opening Width
Shelf detail showing the deflector vent installed.Shelf detail showing the deflector ventduring installation.
Position deflector vent and mark holes.Pre drill using a 1/16" (1.57 mm) bit before mounting.
SKSMD2401SMICROWAVE OVEN DRAWER
1 5/16" (33 mm)Door Thickness
15" (381 mm)Auto Drawer
Opening
4 11/16" (119 mm)
1 3/4" (44 mm)
4" (102 mm)
21 5/8"(549 mm)
14 19/32"(371 mm)
21 7/8" (556 mm)
23 7/8"(606 mm)
15 15/16"(405 mm)
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Suggested electricaloutlet location*
6" (152 mm)
5" (127 mm)
4" (101 mm)
3 1/2" (89 mm)
15 9/16"(395 mm)
36" (914 mm)Countertop
Height
24" (914 mm)Cabinet Minimum
23 1/2"(597 mm)Minimum
Depth
B
D
C
A
A
22 1/8"(562 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
C - Allow 7/16" (11 mm) minimum space
A - Allow 7/8" (22 mm) overlapB - Allow 3/16" (5 mm) overlap
D - Allow 1/8" (3 mm) overlap
Standard (Proud) InstallationOverall Product Dimensions
Mounting Screw Location
Flush Installation
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Anti-Tip BlockSuggested electrical
outlet location*
4"(101 mm)
3 1/2" (89 mm)
6" (152 mm)
23 1/2" (597 mm)Minimum Depth
16 15/16" (430 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
5" (127 mm)
24 3/16" (614 mm) Minimum24 1/2" (622 mm) Maximum
1 1/16" (27 mm)
1 3/4" (44 mm)
22 1/8"(562 mm)
1 3/4"(44 mm)
Note: the face of theshelf must sit 1 3/4"
(44.4 mm) back fromthe face of the cabinet.
Shelfface Cabinet face
Note: the mounting surface of thefinished cleat must sit 1 1/16" (27 mm)back from the face of the cabinet (pushingthe face of the drawer out 1/4" (6 mm))
Anti-Tip Block
Cabinet face
Drawerface
Mountingcleat
Top view
22 1/8"(562 mm)
Mounting cleatopening width
CL
True Flush Installation
16 7/8"(429 mm)
Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet.
Top viewCL
Cabinet face
Drawerface
Mountingcleat
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
22 1/8"(562 mm)
Mounting cleatopening width
MountingFlange
Flush Installation Deflector Vent
Side View
FrontFace ofCabinet
16 15/16"(430 mm)
FlushOpeningHeight
3/4" (19 mm)Shelf
1 3/4" (44 mm)Front Face of Shelf
Anti-Tip Block
No Oven
Front View
SuggestedElectrical
OutletLocation
Anti-Tip Block
3/4" (19 mm)Shelf
22 1/8" (562 mm)Mounting Cleat Opening Width
24 3/16" (614 mm) Min24 1/2" (622 mm) MaxFlush Opening Width
Shelf detail showing the deflector vent installed.Shelf detail showing the deflector ventduring installation.
Position deflector vent and mark holes.Pre drill using a 1/16" (1.57 mm) bit before mounting.
STANDARD (PROUD) INSTALLATION
Page 3 of 6 | Effective 6/20 | WCAG
Notes
The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 100 pounds).
Electrical
A 120V, 60Hz grounded power receptacle should be installed at the back of the cabinet opening.
Warning
Be sure that the clearance of the floor between the wall oven and the microwave drawer is a minimum of 2-inches.
SKSMD2401SMICROWAVE OVEN DRAWER
A growing trend in the installation of kitchen appliances is mounting flush. This allows the consumer to present their appliances with a clean, flush with the cabinet face appearance. In this installation type, there are two ways to accomplish this look: 1/4" front extended and true flush.
1 5/16" (33 mm)Door Thickness
15" (381 mm)Auto Drawer
Opening
4 11/16" (119 mm)
1 3/4" (44 mm)
4" (102 mm)
21 5/8"(549 mm)
14 19/32"(371 mm)
21 7/8" (556 mm)
23 7/8"(606 mm)
15 15/16"(405 mm)
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Suggested electricaloutlet location*
6" (152 mm)
5" (127 mm)
4" (101 mm)
3 1/2" (89 mm)
15 9/16"(395 mm)
36" (914 mm)Countertop
Height
24" (914 mm)Cabinet Minimum
23 1/2"(597 mm)Minimum
Depth
B
D
C
A
A
22 1/8"(562 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
C - Allow 7/16" (11 mm) minimum space
A - Allow 7/8" (22 mm) overlapB - Allow 3/16" (5 mm) overlap
D - Allow 1/8" (3 mm) overlap
Standard (Proud) InstallationOverall Product Dimensions
Mounting Screw Location
Flush Installation
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Anti-Tip BlockSuggested electrical
outlet location*
4"(101 mm)
3 1/2" (89 mm)
6" (152 mm)
23 1/2" (597 mm)Minimum Depth
16 15/16" (430 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
5" (127 mm)
24 3/16" (614 mm) Minimum24 1/2" (622 mm) Maximum
1 1/16" (27 mm)
1 3/4" (44 mm)
22 1/8"(562 mm)
1 3/4"(44 mm)
Note: the face of theshelf must sit 1 3/4"
(44.4 mm) back fromthe face of the cabinet.
Shelfface Cabinet face
Note: the mounting surface of thefinished cleat must sit 1 1/16" (27 mm)back from the face of the cabinet (pushingthe face of the drawer out 1/4" (6 mm))
Anti-Tip Block
Cabinet face
Drawerface
Mountingcleat
Top view
22 1/8"(562 mm)
Mounting cleatopening width
CL
True Flush Installation
16 7/8"(429 mm)
Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet.
Top viewCL
Cabinet face
Drawerface
Mountingcleat
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
22 1/8"(562 mm)
Mounting cleatopening width
MountingFlange
Flush Installation Deflector Vent
Side View
FrontFace ofCabinet
16 15/16"(430 mm)
FlushOpeningHeight
3/4" (19 mm)Shelf
1 3/4" (44 mm)Front Face of Shelf
Anti-Tip Block
No Oven
Front View
SuggestedElectrical
OutletLocation
Anti-Tip Block
3/4" (19 mm)Shelf
22 1/8" (562 mm)Mounting Cleat Opening Width
24 3/16" (614 mm) Min24 1/2" (622 mm) MaxFlush Opening Width
Shelf detail showing the deflector vent installed.Shelf detail showing the deflector ventduring installation.
Position deflector vent and mark holes.Pre drill using a 1/16" (1.57 mm) bit before mounting.
FLUSH (1/4" FRONT EXTENDED) INSTALLATION – REQUIRES DEFLECTOR VENT (KIT INCLUDED)
Page 4 of 6 | Effective 6/20 | WCAG
Notes
In the flush 1/4" front extended application, the appliance can be mounted slightly “proud” of the cabinet cutout, which will create a flush appearance. Having the 1/4" extension also allows to hide the cabinet cutout edges.
SKSMD2401SMICROWAVE OVEN DRAWER
TRUE FLUSH INSTALLATION – REQUIRES DEFLECTOR VENT (KIT INCLUDED)
Page 5 of 6 | Effective 6/20 | WCAG
1 5/16" (33 mm)Door Thickness
15" (381 mm)Auto Drawer
Opening
4 11/16" (119 mm)
1 3/4" (44 mm)
4" (102 mm)
21 5/8"(549 mm)
14 19/32"(371 mm)
21 7/8" (556 mm)
23 7/8"(606 mm)
15 15/16"(405 mm)
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Suggested electricaloutlet location*
6" (152 mm)
5" (127 mm)
4" (101 mm)
3 1/2" (89 mm)
15 9/16"(395 mm)
36" (914 mm)Countertop
Height
24" (914 mm)Cabinet Minimum
23 1/2"(597 mm)Minimum
Depth
B
D
C
A
A
22 1/8"(562 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
C - Allow 7/16" (11 mm) minimum space
A - Allow 7/8" (22 mm) overlapB - Allow 3/16" (5 mm) overlap
D - Allow 1/8" (3 mm) overlap
Standard (Proud) InstallationOverall Product Dimensions
Mounting Screw Location
Flush Installation
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Anti-Tip BlockSuggested electrical
outlet location*
4"(101 mm)
3 1/2" (89 mm)
6" (152 mm)
23 1/2" (597 mm)Minimum Depth
16 15/16" (430 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
5" (127 mm)
24 3/16" (614 mm) Minimum24 1/2" (622 mm) Maximum
1 1/16" (27 mm)
1 3/4" (44 mm)
22 1/8"(562 mm)
1 3/4"(44 mm)
Note: the face of theshelf must sit 1 3/4"
(44.4 mm) back fromthe face of the cabinet.
Shelfface Cabinet face
Note: the mounting surface of thefinished cleat must sit 1 1/16" (27 mm)back from the face of the cabinet (pushingthe face of the drawer out 1/4" (6 mm))
Anti-Tip Block
Cabinet face
Drawerface
Mountingcleat
Top view
22 1/8"(562 mm)
Mounting cleatopening width
CL
True Flush Installation
16 7/8"(429 mm)
Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet.
Top viewCL
Cabinet face
Drawerface
Mountingcleat
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
22 1/8"(562 mm)
Mounting cleatopening width
MountingFlange
Flush Installation Deflector Vent
Side View
FrontFace ofCabinet
16 15/16"(430 mm)
FlushOpeningHeight
3/4" (19 mm)Shelf
1 3/4" (44 mm)Front Face of Shelf
Anti-Tip Block
No Oven
Front View
SuggestedElectrical
OutletLocation
Anti-Tip Block
3/4" (19 mm)Shelf
22 1/8" (562 mm)Mounting Cleat Opening Width
24 3/16" (614 mm) Min24 1/2" (622 mm) MaxFlush Opening Width
Shelf detail showing the deflector vent installed.Shelf detail showing the deflector ventduring installation.
Position deflector vent and mark holes.Pre drill using a 1/16" (1.57 mm) bit before mounting.
Notes
In the true flush application, the appliance is mounted just as described, truly flush with the cabinet face. However, due to the appliance face and the cabinet face being on the same plane, the cabinet cutout edges will be visible and exposed. It is recommended in this true flush installation to finish / stain these edges.
Page 6 of 6 | Effective 6/20 | WCAG
SKSMD2401SMICROWAVE OVEN DRAWER
1 5/16" (33 mm)Door Thickness
15" (381 mm)Auto Drawer
Opening
4 11/16" (119 mm)
1 3/4" (44 mm)
4" (102 mm)
21 5/8"(549 mm)
14 19/32"(371 mm)
21 7/8" (556 mm)
23 7/8"(606 mm)
15 15/16"(405 mm)
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Suggested electricaloutlet location*
6" (152 mm)
5" (127 mm)
4" (101 mm)
3 1/2" (89 mm)
15 9/16"(395 mm)
36" (914 mm)Countertop
Height
24" (914 mm)Cabinet Minimum
23 1/2"(597 mm)Minimum
Depth
B
D
C
A
A
22 1/8"(562 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
C - Allow 7/16" (11 mm) minimum space
A - Allow 7/8" (22 mm) overlapB - Allow 3/16" (5 mm) overlap
D - Allow 1/8" (3 mm) overlap
Standard (Proud) InstallationOverall Product Dimensions
Mounting Screw Location
Flush Installation
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
Anti-Tip BlockSuggested electrical
outlet location*
4"(101 mm)
3 1/2" (89 mm)
6" (152 mm)
23 1/2" (597 mm)Minimum Depth
16 15/16" (430 mm)
14 13/16" (376 mm)to Bottom of Anti-Tip Block
5" (127 mm)
24 3/16" (614 mm) Minimum24 1/2" (622 mm) Maximum
1 1/16" (27 mm)
1 3/4" (44 mm)
22 1/8"(562 mm)
1 3/4"(44 mm)
Note: the face of theshelf must sit 1 3/4"
(44.4 mm) back fromthe face of the cabinet.
Shelfface Cabinet face
Note: the mounting surface of thefinished cleat must sit 1 1/16" (27 mm)back from the face of the cabinet (pushingthe face of the drawer out 1/4" (6 mm))
Anti-Tip Block
Cabinet face
Drawerface
Mountingcleat
Top view
22 1/8"(562 mm)
Mounting cleatopening width
CL
True Flush Installation
16 7/8"(429 mm)
Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet.
Top viewCL
Cabinet face
Drawerface
Mountingcleat
Anti-Tip Block
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges.
22 1/8"(562 mm)
Mounting cleatopening width
MountingFlange
Flush Installation Deflector Vent
Side View
FrontFace ofCabinet
16 15/16"(430 mm)
FlushOpeningHeight
3/4" (19 mm)Shelf
1 3/4" (44 mm)Front Face of Shelf
Anti-Tip Block
No Oven
Front View
SuggestedElectrical
OutletLocation
Anti-Tip Block
3/4" (19 mm)Shelf
22 1/8" (562 mm)Mounting Cleat Opening Width
24 3/16" (614 mm) Min24 1/2" (622 mm) MaxFlush Opening Width
Shelf detail showing the deflector vent installed.Shelf detail showing the deflector ventduring installation.
Position deflector vent and mark holes.Pre drill using a 1/16" (1.57 mm) bit before mounting.
DEFLECTOR VENT KIT INSTALLATION – REQUIRED FOR FLUSH AND TRUE FLUSH INSTALLATION
Top Related