EPSF/EPSM / EPSW-PN
New Produc t News No.1201E-8 2020-10
Epoch SUS series
2020-10(K)2012-1:FP
Attentions on Safety
2. Cautions regarding mounting(1) Before use, check the outside appearance of the tool for scratches, cracks, etc. and that it is firmly mounted in the collet chuck, etc.(2) If abnormal chattering, etc. occurs during use, stop the machine immediately and remove the cause of the chattering.
4. Cautions regarding regrinding(1) If regrinding is not performed at the proper time, there is a risk of the tool breaking. Replace the tool with one in good condition, or perform regrinding.(2) Grinding dust will be created when regrinding a tool. When regrinding, be sure to attach a safety cover over the work area and wear safety clothes such as safety
goggles, etc.(3) This product contains the specified chemical substance cobalt and its inorganic compounds. When performing regrinding or similar processing, be sure to handle the
processing in accordance with thelocal laws and regulations regarding prevention of hazards due to specified chemical substances.
1. Cautions regarding handling(1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands.
3. Cautions during use(1) Before use, confirm the dimensions and direction of rotation of the tool and milling work material.(2) The numerical values in the standard cutting conditions table should be used as criteria when starting new work. The cutting conditions should be adjusted as
appropriate when the cutting depth is large, the rigidity of the machine being used is low, or according to the conditions of the work material.(3) Cutting tools are made of a hard material. During use, they may break and fly off. In addition, cutting chips may also fly off. Since there is a danger of injury to
workers, fire, or eye damage from such flying pieces, a safety cover should be attached when work is performed and safety equipment such as safety goggles should be worn to create a safe environment for work.
(4) There is a risk of fire or inflammation due to sparks, heat due to breakage, and cutting chips. Do not use where there is a risk of fire or explosion. Please caution of fire while using oil base coolant, fire prevention is necessary.
(5) Do not use the tool for any purpose other than that for which it is intended.
Specifications for the products listed in this catalog are subject to change without notice due to replacement or modification. Printed in JAPAN
Printed using vegetable oil ink.
The diagrams and table data are examples of test results, and are not guaranteed values.“ ” is a registered trademark of MOLDINO Tool Engineering, Ltd.
Official Web Site
Database for selection Cutting Tool Products 【TOOL SEARCH】
http://www.moldino.com/en/Head OfficeHulic Ryogoku Bldg. 8F, 4-31-11, Ryogoku, Sumida-ku, Tokyo, Japan 130-0026International Sales Dept. : TEL +81-3-6890-5103 FAX +81-3-6890-5128
MOLDINO Tool Engineering Europe GmbHItterpark 12, 40724 Hilden,Germany. Tel +49-(0)2103-24820 Fax +49-(0)2103-248230
MOLDINO Tool Engineering (Shanghai), Ltd.Room 2604-2605, Metro Plaza, 555 Loushanguan Road, Changning Disctrict,Shanghai, 200051, China Tel +86-(0)21-3366-3058 Fax +86-(0)21-3366-3050
MITSUBISHI MATERIALS U.S.A. CORPORATIONDETROIT OFFICE Customer service41700 Gardenbrook Road, Suite 120, Novi, MI 48375-1320 U.S.A.Tel +1(248) 308-2620 Fax +1(248) 308-2627CHICAGO OFFICE1314B North Plum Grove Road, Schaumburg, IL 60173 U.S.A. Tel +1(847) 252-6371 Fax +1(248) 308-2627
MMC METAL DE MEXICO, S.A. DE C.V.Av. La Cañada No.16, Parque Industrial Bernardo Quintana, El Marques, Querétaro, CP 76246, MéxicoTel +52-442-1926800
Search Web
DISTRIBUTED BY:
Europe
China
America
Mexico
MMC METAL DO BRASIL LTDA. Rua Cincinato Braga, 340 13° andar.Bela Vista – CEP 01333-010 São Paulo – SP ., Brasil Tel +55(11)3506-5600 Fax +55(11)3506-5677
MMC Hardmetal (Thailand) Co.,Ltd. MOLDINO Division622 Emporium Tower, Floor 22/1-4, Sukhumvit Road, Klong Tan, Klong Toei, Bangkok 10110, ThailandTEL:+66-(0)2-661-8175 FAX:+66-(0)2-661-8176
Hitachi Metals (India) Pvt. Ltd.Plot No 94 & 95,Sector 8, IMT Manesar ,Gurgaon-122050 , Haryana, India Tel +91-124-4812315 Fax +91-124-2290015
Thailand
Brazil
India
Epoch SUS Finish, Epoch SUS Multi, Epoch SUS Wave
Additional lineup of Epoch SUS Finish for finishing.(size : φ3.0~12.0 36 items)
Features of Epoch SUS series
01
Abundant lineup! Adapt various machining from roughing to finishing.
ap
ae
Realization of high geometrical precision & surface quality in finishing & super-finishing application.
Versatility in both roughing and finishing applications. Realization of long-tool-life & stable machining by double-eccentric relief face.
Cutting force is reduced by roughing type. Realization of less chatter machining even in low-rigidity situations including spindle, clamping, parts geometry.
Roughing~ Finishing
Roughing
Finishing
Short
Flute length1.5Dc
Flute tip shape
P.8 P.10 P.14 P.16 P.17
P.20 P.21 P.21 P.22
P.12 P.15 P.18
Regular
Flute length2.5Dc
Long
Flute length5Dc
Under neck3Dc
Flute length1.5Dc
Under neck5Dc
Flute length1.5Dc
Squ
are
Squ
are
Squ
are
Rad
ius
EPSMS4-PN
127 Items
EPSM4-PN
217 Items
EPSML4-PN
15 ItemsP.14
EPSMM4-PN
12 Items P.15
EPSMLS4-PN
13 Items
EPSM4-3Dc-PN
31 Items
EPSM4-5Dc-PN
31 Items
EPSW-PN
25 Items
EPSWL-PN
15 Items
EPSW-3Dc-PN
11 Items
EPSW-5Dc-PN
11 Items
EPSM4-CR-PN
82 Items
EPSML4-CR-PN
32 Items
EPSM4-5Dc-CR-PN
82 Items
Long shank
Flute length1.5Dc
Medium
Flute length4Dc
Overview of Epoch SUS Series
Line-ups of Epoch SUS series
Features 01 Unequal pitch geometryDramatically suppressing vibration
03 Introduction of Double-eccentric relief faceImproving chipping-resistance & wear-resistance
02 Double GashSmooth chip evacuation
Applications EPSF-PN :φ3~φ12 [ 36 Items]
EPSM-PN :φ1~φ20 [ 642 Items]
EPSW-PN :φ4~φ20 [ 62 Items]
Suppressing vibration by unequal pitch geometry.
02 Smooth chip evacuation by double gash
03 Improving chipping-resistance & wear-resistanceby double-eccentric relief face.
04 Smooth chip evacuation by optimized flute geometry
05 Improving wear-resistance and tool life by PN coating.
0302
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
P.6
EPSF-PN
13 Items P.7
EPSFM-PN
13 Items P.7
EPSFL-PN
10 Items
Cutting condition
Re-grinding
Technical Data
φ1~φ20 φ1~φ20 φ3~φ20 φ6~φ20
φ3~φ12 φ3~φ12 φ3~φ12
φ3~φ17 φ1~φ20 φ1~φ20
φ4~φ20 φ6~φ20 φ4~φ20 φ4~φ20
φ1~φ20 φ6~φ20 φ1~φ20
Planing Side cutting Slotting Die-sinking Profiling Radius Helical Spot facing
Epoch®
Epoch®
Epoch® Wave
Wave
Tool:Square type φ8×4NT, Work material:SUS304, Rotation : n=2100min-1 , Feed rate :vf=230mm/min, ap×ae = 6.4×8mm, Coolant:Wet
α°
β°
β°
α°
EPSM Unequal pitch geometry EPSM (Unequal pitch) Conventional (Equal pitch)
Cutting force in slotting
Brokenduring cutting
Features
Features
1st gash for high rigidity !
2nd gash for stable chipevacuation !
’’Double Gash’’ achieves perfect balance with rigidity and chip evacuation!It guarantees high performance in vertical and horizontal milling!
1st gash1st gash
2nd gash2nd gash
Double Gash Conventional single gash
Wear status after SUS304 side milling
Double-Eccentric Traditional relief face
1st eccentric relief face1st eccentric relief face
2nd eccentricrelief face2nd eccentricrelief face
Rakeface
Crosssection
Rakeface Relief
face
Crosssection
Cutting edgeCutting edge
Double-eccentric relief face realize a small wear when guaranteeing higher cutting edge rigidity.
1st eccentric relief face
2nd eccentric relief face
Wear is restrictedby first eccentric rilief face
Flank wear extendedto the dotted line.
EPSF EPSM
EPSM
EPSW
EPSF EPSM EPSW
EPSM
EPSM
EPSW
EPSF EPSM EPSW
EPSF
EPSM
EPSW
EPSW
EPSM EPSW
EPSF-PN
EPSM-PN
EPSW-PN
PN Coating
Copper Carbon steelAlloy steel
Stainless steelTool steel
Pre-hardenedsteel
Hardened steel45~55HRC
Hardened steel55~65HRC
Features of Epoch SUS series
01
Abundant lineup! Adapt various machining from roughing to finishing.
ap
ae
Realization of high geometrical precision & surface quality in finishing & super-finishing application.
Versatility in both roughing and finishing applications. Realization of long-tool-life & stable machining by double-eccentric relief face.
Cutting force is reduced by roughing type. Realization of less chatter machining even in low-rigidity situations including spindle, clamping, parts geometry.
Roughing~ Finishing
Roughing
Finishing
Short
Flute length1.5Dc
Flute tip shape
P.8 P.10 P.14 P.16 P.17
P.20 P.21 P.21 P.22
P.12 P.15 P.18
Regular
Flute length2.5Dc
Long
Flute length5Dc
Under neck3Dc
Flute length1.5Dc
Under neck5Dc
Flute length1.5Dc
Squ
are
Squ
are
Squ
are
Rad
ius
EPSMS4-PN
127 Items
EPSM4-PN
217 Items
EPSML4-PN
15 ItemsP.14
EPSMM4-PN
12 Items P.15
EPSMLS4-PN
13 Items
EPSM4-3Dc-PN
31 Items
EPSM4-5Dc-PN
31 Items
EPSW-PN
25 Items
EPSWL-PN
15 Items
EPSW-3Dc-PN
11 Items
EPSW-5Dc-PN
11 Items
EPSM4-CR-PN
82 Items
EPSML4-CR-PN
32 Items
EPSM4-5Dc-CR-PN
82 Items
Long shank
Flute length1.5Dc
Medium
Flute length4Dc
Overview of Epoch SUS Series
Line-ups of Epoch SUS series
Features 01 Unequal pitch geometryDramatically suppressing vibration
03 Introduction of Double-eccentric relief faceImproving chipping-resistance & wear-resistance
02 Double GashSmooth chip evacuation
Applications EPSF-PN :φ3~φ12 [ 36 Items]
EPSM-PN :φ1~φ20 [ 642 Items]
EPSW-PN :φ4~φ20 [ 62 Items]
Suppressing vibration by unequal pitch geometry.
02 Smooth chip evacuation by double gash
03 Improving chipping-resistance & wear-resistanceby double-eccentric relief face.
04 Smooth chip evacuation by optimized flute geometry
05 Improving wear-resistance and tool life by PN coating.
0302
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
P.6
EPSF-PN
13 Items P.7
EPSFM-PN
13 Items P.7
EPSFL-PN
10 Items
Cutting condition
Re-grinding
Technical Data
φ1~φ20 φ1~φ20 φ3~φ20 φ6~φ20
φ3~φ12 φ3~φ12 φ3~φ12
φ3~φ17 φ1~φ20 φ1~φ20
φ4~φ20 φ6~φ20 φ4~φ20 φ4~φ20
φ1~φ20 φ6~φ20 φ1~φ20
Planing Side cutting Slotting Die-sinking Profiling Radius Helical Spot facing
Epoch®
Epoch®
Epoch® Wave
Wave
Tool:Square type φ8×4NT, Work material:SUS304, Rotation : n=2100min-1 , Feed rate :vf=230mm/min, ap×ae = 6.4×8mm, Coolant:Wet
α°
β°
β°
α°
EPSM Unequal pitch geometry EPSM (Unequal pitch) Conventional (Equal pitch)
Cutting force in slotting
Brokenduring cutting
Features
Features
1st gash for high rigidity !
2nd gash for stable chipevacuation !
’’Double Gash’’ achieves perfect balance with rigidity and chip evacuation!It guarantees high performance in vertical and horizontal milling!
1st gash1st gash
2nd gash2nd gash
Double Gash Conventional single gash
Wear status after SUS304 side milling
Double-Eccentric Traditional relief face
1st eccentric relief face1st eccentric relief face
2nd eccentricrelief face2nd eccentricrelief face
Rakeface
Crosssection
Rakeface Relief
face
Crosssection
Cutting edgeCutting edge
Double-eccentric relief face realize a small wear when guaranteeing higher cutting edge rigidity.
1st eccentric relief face
2nd eccentric relief face
Wear is restrictedby first eccentric rilief face
Flank wear extendedto the dotted line.
EPSF EPSM
EPSM
EPSW
EPSF EPSM EPSW
EPSM
EPSM
EPSW
EPSF EPSM EPSW
EPSF
EPSM
EPSW
EPSW
EPSM EPSW
EPSF-PN
EPSM-PN
EPSW-PN
PN Coating
Copper Carbon steelAlloy steel
Stainless steelTool steel
Pre-hardenedsteel
Hardened steel45~55HRC
Hardened steel55~65HRC
0504
Cutting force comparison by cutting depth amount (when performing side cutting with φ8mm tool)
■ Epoch SUS Wave ap & ae
320305258208
7654321
604556481406309
928824713589456308
12311081932778604412221
147613421124916699495269
1802164013991151864598314
2094188315991300995679367
24202140181414891144781427
1 2 3 4 5 6 7 8
Total cutting force (N)
ap(mm)
ae(mm)
2500N~2000~2500N 1500~2000N 1000~1500N 500~1000N ~500N
2500N~2000~2500N 1500~2000N 1000~1500N 500~1000N ~500N
EPSWprovides lower cutting
force at the samecutting depth.
EPSM
EPSW
■ Epoch SUS Multi ap & ae
331302265215
7654321
683626543461362
1053955824689527381
143112751105914714511273
1799161213701125879606340
21561926166213821071745408
25132227192215691214830484
28442538217417771364951539
1 2 3 4 5 6 7 8
Total cutting force (N)
EPSM4080-24-PNWork material : SUS304n=2400min-1(vc=60m/min) vf=380mm/min(fz=0.04mm/t) HSK63A Coolant:Wet
ap(mm)
ae(mm)
ap
ae
EPSW4080-24-PNWork material : SUS304n=2400min-1(vc=60m/min) vf=380mm/min(fz=0.04mm/t) HSK63A Coolant:Wet
ap
ae
※Value indicates total cutting force.※The chart was created beased on experimental data only for reference, please adjust according to user’s own cutting situation.
①If Φ8 endmill with ap=7mm & ae=3mm can lead to a machining. Cutting force of ap=4mm & ae=5mm could be same level.②In the same parameter, EPSW has lower cutting force than EPSM.③In the case of same metal removal rate, lower ap causes lower cutting force.
This table can be reference data for comparing cutting force based on different ap & ae. Lower cutting force could lead to more stable machining.Example. In the case of same cutting situation,
Standarddepth of cut
Standarddepth of cut
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
04
05 PN CoatingImproving wear-resistance and tool life
EPSW
EPSF EPSM EPSW
Optimized Flute geometrySmooth chip evacuation
Features and characteristics・A heat-resistant coating material with excellent adhesion to the tool substrate was achieved by optimizing the Al content.・Exhibits excellent cutting life for cutting materials such as plastic molds, etc. where tool seizure often occurs. Provides the long life in cutting processing of materials starting with HPM-MAGIC and including pre-hardened steel, carbon steel, alloy steel, SUS, SKD61, SKD11, etc. Note) This product obtains less electric conductivity. Therefore, Please caution of using electric transmitted measuring systems.
Features
Features
EPSW Optimized flute geometry Conventional flute geometry
EPSW optimized flute geometry dramatically improves chip-disposalof wave-form cutter
Adhesion of PN coating Cross-sectional structure andcharacteristics of PN coating membrane
Conventional coating PN coating Substrate: Carbide alloy
No peeling ↓
Superior adhesion
Coating is peeling.
Carbide
Coating structureMembrane surface with improved lubrication characteristics
Microstructure increases heat resistance!
Improved adhesion strength
Features
0504
Cutting force comparison by cutting depth amount (when performing side cutting with φ8mm tool)
■ Epoch SUS Wave ap & ae
320305258208
7654321
604556481406309
928824713589456308
12311081932778604412221
147613421124916699495269
1802164013991151864598314
2094188315991300995679367
24202140181414891144781427
1 2 3 4 5 6 7 8
Total cutting force (N)
ap(mm)
ae(mm)
2500N~2000~2500N 1500~2000N 1000~1500N 500~1000N ~500N
2500N~2000~2500N 1500~2000N 1000~1500N 500~1000N ~500N
EPSWprovides lower cutting
force at the samecutting depth.
EPSM
EPSW
■ Epoch SUS Multi ap & ae
331302265215
7654321
683626543461362
1053955824689527381
143112751105914714511273
1799161213701125879606340
21561926166213821071745408
25132227192215691214830484
28442538217417771364951539
1 2 3 4 5 6 7 8
Total cutting force (N)
EPSM4080-24-PNWork material : SUS304n=2400min-1(vc=60m/min) vf=380mm/min(fz=0.04mm/t) HSK63A Coolant:Wet
ap(mm)
ae(mm)
ap
ae
EPSW4080-24-PNWork material : SUS304n=2400min-1(vc=60m/min) vf=380mm/min(fz=0.04mm/t) HSK63A Coolant:Wet
ap
ae
※Value indicates total cutting force.※The chart was created beased on experimental data only for reference, please adjust according to user’s own cutting situation.
①If Φ8 endmill with ap=7mm & ae=3mm can lead to a machining. Cutting force of ap=4mm & ae=5mm could be same level.②In the same parameter, EPSW has lower cutting force than EPSM.③In the case of same metal removal rate, lower ap causes lower cutting force.
This table can be reference data for comparing cutting force based on different ap & ae. Lower cutting force could lead to more stable machining.Example. In the case of same cutting situation,
Standarddepth of cut
Standarddepth of cut
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
04
05 PN CoatingImproving wear-resistance and tool life
EPSW
EPSF EPSM EPSW
Optimized Flute geometrySmooth chip evacuation
Features and characteristics・A heat-resistant coating material with excellent adhesion to the tool substrate was achieved by optimizing the Al content.・Exhibits excellent cutting life for cutting materials such as plastic molds, etc. where tool seizure often occurs. Provides the long life in cutting processing of materials starting with HPM-MAGIC and including pre-hardened steel, carbon steel, alloy steel, SUS, SKD61, SKD11, etc. Note) This product obtains less electric conductivity. Therefore, Please caution of using electric transmitted measuring systems.
Features
Features
EPSW Optimized flute geometry Conventional flute geometry
EPSW optimized flute geometry dramatically improves chip-disposalof wave-form cutter
Adhesion of PN coating Cross-sectional structure andcharacteristics of PN coating membrane
Conventional coating PN coating Substrate: Carbide alloy
No peeling ↓
Superior adhesion
Coating is peeling.
Carbide
Coating structureMembrane surface with improved lubrication characteristics
Microstructure increases heat resistance!
Improved adhesion strength
Features
Item Code Stock Tool dia.Dc
Flute lengthR
Overall lengthL
Shank dia.Ds
ShapeSize (mm)
Item Code Stock Tool dia.Dc
Flute lengthR
Overall lengthL
Shank dia.Ds
ShapeSize (mm)
EPSF4030-PNEPSF4035-PNEPSF4040-PNEPSF4045-PNEPSF4050-PNEPSF4055-PNEPSF4060-PNEPSF4070-PNEPSF4080-PNEPSF4090-PNEPSF4100-PNEPSF4110-PNEPSF4120-PN
★★★★★★★★★★★★★
3 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12
7.5 8.8 10 11.3 12.5 13.8 15 17.5 20 22.5 25 27.5 30
66666668810101212
AAAAAABABABAB
EPSF4 -PN
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
φ3~φ6 φ7~φ12
0-0.015
0-0.02
56565656565656636374748686
Item Code Stock Tool dia.Dc
Flute lengthR
Overall lengthL
Shank dia.Ds
ShapeSize (mm)
4 Flutes 4 Flutes
4 Flutes
0706
EPSFM4030-PNEPSFM4035-PNEPSFM4040-PNEPSFM4045-PNEPSFM4050-PNEPSFM4055-PNEPSFM4060-PNEPSFM4070-PNEPSFM4080-PNEPSFM4090-PNEPSFM4100-PNEPSFM4110-PNEPSFM4120-PN
★★★★★★★★★★★★★
3 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12
12141618202224283236404448
66666668810101212
AAAAAABABABAB
φ3~φ6 φ7~φ12
0-0.015
0-0.02
565656707070707580100100120120
EPSFL4030-PNEPSFL4040-PNEPSFL4050-PNEPSFL4060-PNEPSFL4070-PNEPSFL4080-PNEPSFL4090-PNEPSFL4100-PNEPSFL4110-PNEPSFL4120-PN
★★★★★★★★★★
3456789
101112
15202530354045505560
66668810101212
AAABABABAB
φ3~φ6 φ7~φ12
0-0.015
0-0.02
567070708080100100120120
EPSFM4 -PN Medium
EPSFL4 -PN Long
★:Stocked Items of New Products.
Square type φ3~φ12 Square type φ3~φ12
Square type φ3~φ12
EPSF EPSFM
EPSFL
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
h5 h5
h5
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.29Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.31
Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.31
L ine Up
Epoch Epoch
Epoch
RegularHelix 43° Unequal
PitchCarbideCoated
Helix 43°Carbide
Coated
Helix 43°Carbide
Coated
UnequalPitch
UnequalPitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock Tool dia.Dc
Flute lengthR
Overall lengthL
Shank dia.Ds
ShapeSize (mm)
Item Code Stock Tool dia.Dc
Flute lengthR
Overall lengthL
Shank dia.Ds
ShapeSize (mm)
EPSF4030-PNEPSF4035-PNEPSF4040-PNEPSF4045-PNEPSF4050-PNEPSF4055-PNEPSF4060-PNEPSF4070-PNEPSF4080-PNEPSF4090-PNEPSF4100-PNEPSF4110-PNEPSF4120-PN
★★★★★★★★★★★★★
3 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12
7.5 8.8 10 11.3 12.5 13.8 15 17.5 20 22.5 25 27.5 30
66666668810101212
AAAAAABABABAB
EPSF4 -PN
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
φ3~φ6 φ7~φ12
0-0.015
0-0.02
56565656565656636374748686
Item Code Stock Tool dia.Dc
Flute lengthR
Overall lengthL
Shank dia.Ds
ShapeSize (mm)
4 Flutes 4 Flutes
4 Flutes
0706
EPSFM4030-PNEPSFM4035-PNEPSFM4040-PNEPSFM4045-PNEPSFM4050-PNEPSFM4055-PNEPSFM4060-PNEPSFM4070-PNEPSFM4080-PNEPSFM4090-PNEPSFM4100-PNEPSFM4110-PNEPSFM4120-PN
★★★★★★★★★★★★★
3 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12
12141618202224283236404448
66666668810101212
AAAAAABABABAB
φ3~φ6 φ7~φ12
0-0.015
0-0.02
565656707070707580100100120120
EPSFL4030-PNEPSFL4040-PNEPSFL4050-PNEPSFL4060-PNEPSFL4070-PNEPSFL4080-PNEPSFL4090-PNEPSFL4100-PNEPSFL4110-PNEPSFL4120-PN
★★★★★★★★★★
3456789
101112
15202530354045505560
66668810101212
AAABABABAB
φ3~φ6 φ7~φ12
0-0.015
0-0.02
567070708080100100120120
EPSFM4 -PN Medium
EPSFL4 -PN Long
★:Stocked Items of New Products.
Square type φ3~φ12 Square type φ3~φ12
Square type φ3~φ12
EPSF EPSFM
EPSFL
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
h5 h5
h5
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.29Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.31
Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.31
L ine Up
Epoch Epoch
Epoch
RegularHelix 43° Unequal
PitchCarbideCoated
Helix 43°Carbide
Coated
Helix 43°Carbide
Coated
UnequalPitch
UnequalPitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
EPSMS4010-PNEPSMS4011-PNEPSMS4012-PNEPSMS4013-PNEPSMS4014-PNEPSMS4015-PNEPSMS4016-PNEPSMS4017-PNEPSMS4018-PNEPSMS4019-PNEPSMS4020-PNEPSMS4021-PNEPSMS4022-PNEPSMS4023-PNEPSMS4024-PNEPSMS4025-PNEPSMS4026-PNEPSMS4027-PNEPSMS4028-PNEPSMS4029-PNEPSMS4030-PNEPSMS4031-PNEPSMS4032-PNEPSMS4033-PNEPSMS4034-PNEPSMS4035-PNEPSMS4036-PNEPSMS4037-PNEPSMS4038-PNEPSMS4039-PNEPSMS4040-PNEPSMS4041-PNEPSMS4042-PNEPSMS4043-PNEPSMS4044-PNEPSMS4045-PNEPSMS4046-PNEPSMS4047-PNEPSMS4048-PNEPSMS4049-PN
□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□
11.11.21.31.41.51.61.71.81.922.12.22.32.42.52.62.72.82.933.13.23.33.43.53.63.73.83.944.14.24.34.44.54.64.74.84.9
1.51.71.822.12.32.42.62.72.933.23.33.53.63.83.94.14.24.44.54.74.855.15.35.45.65.75.966.26.36.56.66.86.97.17.27.4
6666666666666666666666666666666666666666
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
EPSMS4 -PNφ1~φ6 φ6.1~φ20 φ6~φ12 φ16,φ20
0-0.015
0-0.02
56565656565656565656565656565656565656565656565656565656565656565656565656565656
EPSMS4050-PNEPSMS4051-PNEPSMS4052-PNEPSMS4053-PNEPSMS4054-PNEPSMS4055-PNEPSMS4056-PNEPSMS4057-PNEPSMS4058-PNEPSMS4059-PNEPSMS4060-PNEPSMS4061-PNEPSMS4062-PNEPSMS4063-PNEPSMS4064-PNEPSMS4065-PNEPSMS4066-PNEPSMS4067-PNEPSMS4068-PNEPSMS4069-PNEPSMS4070-PNEPSMS4071-PNEPSMS4072-PNEPSMS4073-PNEPSMS4074-PNEPSMS4075-PNEPSMS4076-PNEPSMS4077-PNEPSMS4078-PNEPSMS4079-PNEPSMS4080-PNEPSMS4081-PNEPSMS4082-PNEPSMS4083-PNEPSMS4084-PNEPSMS4085-PNEPSMS4086-PNEPSMS4087-PNEPSMS4088-PNEPSMS4089-PN
□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□
55.15.25.35.45.55.65.75.85.966.16.26.36.46.56.66.76.86.977.17.27.37.47.57.67.77.87.988.18.28.38.48.58.68.78.88.9
7.5 7.7 7.8 8 8.1 8.3 8.4 8.6 8.7 8.9 9 9.2 9.3 9.5 9.6 9.8 9.9 10.1 10.2 10.4 10.5 10.7 10.8 11 11.1 11.3 11.4 11.6 11.7 11.9 12 12.2 12.3 12.5 12.6 12.8 12.9 13.1 13.2 13.4
6666666666688888888888888888888101010101010101010
56565656565656565656566363636363636363636363636363636363636363747474747474747474
□:Stocked by specified distributor. Contact with our sales department.
EPSMS4090-PNEPSMS4091-PNEPSMS4092-PNEPSMS4093-PNEPSMS4094-PNEPSMS4095-PNEPSMS4096-PNEPSMS4097-PNEPSMS4098-PNEPSMS4099-PNEPSMS4100-PNEPSMS4101-PNEPSMS4102-PNEPSMS4103-PNEPSMS4104-PNEPSMS4105-PNEPSMS4106-PNEPSMS4107-PNEPSMS4108-PNEPSMS4109-PNEPSMS4110-PNEPSMS4111-PNEPSMS4112-PNEPSMS4113-PNEPSMS4114-PNEPSMS4115-PNEPSMS4116-PNEPSMS4117-PNEPSMS4118-PNEPSMS4119-PNEPSMS4120-PNEPSMS4125-PNEPSMS4130-PNEPSMS4135-PNEPSMS4140-PNEPSMS4145-PNEPSMS4150-PNEPSMS4155-PNEPSMS4160-PNEPSMS4165-PN
□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□
9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12 12.5 13 13.5 14 14.5 15 15.5 16 16.5
13.513.713.81414.114.314.414.614.714.91515.215.315.515.615.815.916.116.216.416.516.716.81717.117.317.417.617.717.91818.819.520.32121.822.523.32424.8
10101010101010101010101212121212121212121212121212121212121212161616161616161620
74747474747474747474748686868686868686868686868686868686868686100100100100100100100100110
EPSMS4170-PNEPSMS4175-PNEPSMS4180-PNEPSMS4185-PNEPSMS4190-PNEPSMS4195-PNEPSMS4200-PN
□□□□□□□
1717.51818.51919.520
25.526.32727.828.529.330
20202020202020
110110110110110110110
AAAAAAAAAABAAAAAAAAAAAAAAAAAAABAAAAAAAAA
AAAAAAAAAABAAAAAAAAAAAAAAAAAAABAAAAAAABA
AAAAAAB
4 Flutes
0908
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
RL
φDcφDc φDsφDs
RL
20°
B typeA type
L ine Up
EPSMSEpoch Multi
Helix 40°Carbide
CoatedUnequal
PitchSquare type φ1~φ20Short EPSMS4 -PN Square type φ1~φ20Short
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
EPSMS4010-PNEPSMS4011-PNEPSMS4012-PNEPSMS4013-PNEPSMS4014-PNEPSMS4015-PNEPSMS4016-PNEPSMS4017-PNEPSMS4018-PNEPSMS4019-PNEPSMS4020-PNEPSMS4021-PNEPSMS4022-PNEPSMS4023-PNEPSMS4024-PNEPSMS4025-PNEPSMS4026-PNEPSMS4027-PNEPSMS4028-PNEPSMS4029-PNEPSMS4030-PNEPSMS4031-PNEPSMS4032-PNEPSMS4033-PNEPSMS4034-PNEPSMS4035-PNEPSMS4036-PNEPSMS4037-PNEPSMS4038-PNEPSMS4039-PNEPSMS4040-PNEPSMS4041-PNEPSMS4042-PNEPSMS4043-PNEPSMS4044-PNEPSMS4045-PNEPSMS4046-PNEPSMS4047-PNEPSMS4048-PNEPSMS4049-PN
□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□
11.11.21.31.41.51.61.71.81.922.12.22.32.42.52.62.72.82.933.13.23.33.43.53.63.73.83.944.14.24.34.44.54.64.74.84.9
1.51.71.822.12.32.42.62.72.933.23.33.53.63.83.94.14.24.44.54.74.855.15.35.45.65.75.966.26.36.56.66.86.97.17.27.4
6666666666666666666666666666666666666666
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
EPSMS4 -PNφ1~φ6 φ6.1~φ20 φ6~φ12 φ16,φ20
0-0.015
0-0.02
56565656565656565656565656565656565656565656565656565656565656565656565656565656
EPSMS4050-PNEPSMS4051-PNEPSMS4052-PNEPSMS4053-PNEPSMS4054-PNEPSMS4055-PNEPSMS4056-PNEPSMS4057-PNEPSMS4058-PNEPSMS4059-PNEPSMS4060-PNEPSMS4061-PNEPSMS4062-PNEPSMS4063-PNEPSMS4064-PNEPSMS4065-PNEPSMS4066-PNEPSMS4067-PNEPSMS4068-PNEPSMS4069-PNEPSMS4070-PNEPSMS4071-PNEPSMS4072-PNEPSMS4073-PNEPSMS4074-PNEPSMS4075-PNEPSMS4076-PNEPSMS4077-PNEPSMS4078-PNEPSMS4079-PNEPSMS4080-PNEPSMS4081-PNEPSMS4082-PNEPSMS4083-PNEPSMS4084-PNEPSMS4085-PNEPSMS4086-PNEPSMS4087-PNEPSMS4088-PNEPSMS4089-PN
□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□
55.15.25.35.45.55.65.75.85.966.16.26.36.46.56.66.76.86.977.17.27.37.47.57.67.77.87.988.18.28.38.48.58.68.78.88.9
7.5 7.7 7.8 8 8.1 8.3 8.4 8.6 8.7 8.9 9 9.2 9.3 9.5 9.6 9.8 9.9 10.1 10.2 10.4 10.5 10.7 10.8 11 11.1 11.3 11.4 11.6 11.7 11.9 12 12.2 12.3 12.5 12.6 12.8 12.9 13.1 13.2 13.4
6666666666688888888888888888888101010101010101010
56565656565656565656566363636363636363636363636363636363636363747474747474747474
□:Stocked by specified distributor. Contact with our sales department.
EPSMS4090-PNEPSMS4091-PNEPSMS4092-PNEPSMS4093-PNEPSMS4094-PNEPSMS4095-PNEPSMS4096-PNEPSMS4097-PNEPSMS4098-PNEPSMS4099-PNEPSMS4100-PNEPSMS4101-PNEPSMS4102-PNEPSMS4103-PNEPSMS4104-PNEPSMS4105-PNEPSMS4106-PNEPSMS4107-PNEPSMS4108-PNEPSMS4109-PNEPSMS4110-PNEPSMS4111-PNEPSMS4112-PNEPSMS4113-PNEPSMS4114-PNEPSMS4115-PNEPSMS4116-PNEPSMS4117-PNEPSMS4118-PNEPSMS4119-PNEPSMS4120-PNEPSMS4125-PNEPSMS4130-PNEPSMS4135-PNEPSMS4140-PNEPSMS4145-PNEPSMS4150-PNEPSMS4155-PNEPSMS4160-PNEPSMS4165-PN
□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□□
9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 10 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 12 12.5 13 13.5 14 14.5 15 15.5 16 16.5
13.513.713.81414.114.314.414.614.714.91515.215.315.515.615.815.916.116.216.416.516.716.81717.117.317.417.617.717.91818.819.520.32121.822.523.32424.8
10101010101010101010101212121212121212121212121212121212121212161616161616161620
74747474747474747474748686868686868686868686868686868686868686100100100100100100100100110
EPSMS4170-PNEPSMS4175-PNEPSMS4180-PNEPSMS4185-PNEPSMS4190-PNEPSMS4195-PNEPSMS4200-PN
□□□□□□□
1717.51818.51919.520
25.526.32727.828.529.330
20202020202020
110110110110110110110
AAAAAAAAAABAAAAAAAAAAAAAAAAAAABAAAAAAAAA
AAAAAAAAAABAAAAAAAAAAAAAAAAAAABAAAAAAABA
AAAAAAB
4 Flutes
0908
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
RL
φDcφDc φDsφDs
RL
20°
B typeA type
L ine Up
EPSMSEpoch Multi
Helix 40°Carbide
CoatedUnequal
PitchSquare type φ1~φ20Short EPSMS4 -PN Square type φ1~φ20Short
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
1110
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
EPSM4010-PNEPSM40105-PNEPSM4011-PNEPSM40115-PNEPSM4012-PNEPSM40125-PNEPSM4013-PNEPSM40135-PNEPSM4014-PNEPSM40145-PNEPSM4015-PNEPSM40155-PNEPSM4016-PNEPSM40165-PNEPSM4017-PNEPSM40175-PNEPSM4018-PNEPSM40185-PNEPSM4019-PNEPSM40195-PNEPSM4020-PNEPSM40205-PNEPSM4021-PNEPSM40215-PNEPSM4022-PNEPSM40225-PNEPSM4023-PNEPSM40235-PNEPSM4024-PNEPSM40245-PNEPSM4025-PNEPSM40255-PNEPSM4026-PNEPSM40265-PNEPSM4027-PNEPSM40275-PNEPSM4028-PNEPSM40285-PNEPSM4029-PNEPSM40295-PNEPSM4030-PNEPSM40305-PNEPSM4031-PNEPSM40315-PNEPSM4032-PNEPSM40325-PNEPSM4033-PNEPSM40335-PNEPSM4034-PNEPSM40345-PNEPSM4035-PNEPSM40355-PNEPSM4036-PNEPSM40365-PNEPSM4037-PN
●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□
11.051.11.151.21.251.31.351.41.451.51.551.61.651.71.751.81.851.91.9522.052.12.152.22.252.32.352.42.452.52.552.62.652.72.752.82.852.92.9533.053.13.153.23.253.33.353.43.453.53.553.63.653.7
2.52.82.8333.33.33.53.53.83.8444.34.34.54.54.84.8555.35.35.55.55.85.8666.36.36.56.56.86.8777.37.37.57.57.87.8888.38.38.58.58.88.8999.39.3
6666666666666666666666666666666666666666666666666666666
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
56565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656
EPSM40375-PNEPSM4038-PNEPSM40385-PNEPSM4039-PNEPSM40395-PNEPSM4040-PNEPSM40405-PNEPSM4041-PNEPSM40415-PNEPSM4042-PNEPSM40425-PNEPSM4043-PNEPSM40435-PNEPSM4044-PNEPSM40445-PNEPSM4045-PNEPSM40455-PNEPSM4046-PNEPSM40465-PNEPSM4047-PNEPSM40475-PNEPSM4048-PNEPSM40485-PNEPSM4049-PNEPSM40495-PNEPSM4050-PNEPSM40505-PNEPSM4051-PNEPSM40515-PNEPSM4052-PNEPSM40525-PNEPSM4053-PNEPSM40535-PNEPSM4054-PNEPSM40545-PNEPSM4055-PNEPSM40555-PNEPSM4056-PNEPSM40565-PNEPSM4057-PNEPSM40575-PNEPSM4058-PNEPSM40585-PNEPSM4059-PNEPSM40595-PNEPSM4060-PNEPSM40605-PNEPSM4061-PNEPSM40615-PNEPSM4062-PNEPSM40625-PNEPSM4063-PNEPSM40635-PNEPSM4064-PNEPSM40645-PN
□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□
3.753.83.853.93.9544.054.14.154.24.254.34.354.44.454.54.554.64.654.74.754.84.854.94.9555.055.15.155.25.255.35.355.45.455.55.555.65.655.75.755.85.855.95.9566.056.16.156.26.256.36.356.46.45
9.5 9.5 9.8 9.8 10 10 10.3 10.3 10.5 10.5 10.8 10.8 11 11 11.3 11.3 11.5 11.5 11.8 11.8 12 12 12.3 12.3 12.5 12.5 12.8 12.8 13 13 13.3 13.3 13.5 13.5 13.8 13.8 14 14 14.3 14.3 14.5 14.5 14.8 14.8 15 15 15.3 15.3 15.5 15.5 15.8 15.8 16 16 16.3
6666666666666666666666666666666666666666666666888888888
56565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656636363636363636363
EPSM4065-PNEPSM40655-PNEPSM4066-PNEPSM40665-PNEPSM4067-PNEPSM40675-PNEPSM4068-PNEPSM40685-PNEPSM4069-PNEPSM40695-PNEPSM4070-PNEPSM40705-PNEPSM4071-PNEPSM40715-PNEPSM4072-PNEPSM40725-PNEPSM4073-PNEPSM40735-PNEPSM4074-PNEPSM40745-PNEPSM4075-PNEPSM40755-PNEPSM4076-PNEPSM40765-PNEPSM4077-PNEPSM40775-PNEPSM4078-PNEPSM40785-PNEPSM4079-PNEPSM40795-PNEPSM4080-PNEPSM40805-PNEPSM4081-PNEPSM40815-PNEPSM4082-PNEPSM40825-PNEPSM4083-PNEPSM40835-PNEPSM4084-PNEPSM40845-PNEPSM4085-PNEPSM40855-PNEPSM4086-PNEPSM40865-PNEPSM4087-PNEPSM40875-PNEPSM4088-PNEPSM40885-PNEPSM4089-PNEPSM40895-PNEPSM4090-PNEPSM40905-PNEPSM4091-PNEPSM40915-PNEPSM4092-PN
□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□
6.56.556.66.656.76.756.86.856.96.9577.057.17.157.27.257.37.357.47.457.57.557.67.657.77.757.87.857.97.9588.058.18.158.28.258.38.358.48.458.58.558.68.658.78.758.88.858.98.9599.059.19.159.2
16.316.516.516.816.8171717.317.317.517.517.817.8181818.318.318.518.518.818.8191919.319.319.519.519.819.8202020.320.320.520.520.820.8212121.321.321.521.521.821.8222222.322.322.522.522.822.82323
8888888888888888888888888888888101010101010101010101010101010101010101010101010
63636363636363636363636363636363636363636363636363636363636363747474747474747474747474747474747474747474747474
EPSM40925-PNEPSM4093-PNEPSM40935-PNEPSM4094-PNEPSM40945-PNEPSM4095-PNEPSM40955-PNEPSM4096-PNEPSM40965-PNEPSM4097-PNEPSM40975-PNEPSM4098-PNEPSM40985-PNEPSM4099-PNEPSM40995-PNEPSM4100-PNEPSM4101-PNEPSM4102-PNEPSM4103-PNEPSM4104-PNEPSM4105-PNEPSM4106-PNEPSM4107-PNEPSM4108-PNEPSM4109-PNEPSM4110-PNEPSM4111-PNEPSM4112-PNEPSM4113-PNEPSM4114-PNEPSM4115-PNEPSM4116-PNEPSM4117-PNEPSM4118-PNEPSM4119-PNEPSM4120-PNEPSM4125-PNEPSM4130-PNEPSM4135-PNEPSM4140-PNEPSM4145-PNEPSM4150-PNEPSM4155-PNEPSM4160-PNEPSM4165-PNEPSM4170-PNEPSM4175-PNEPSM4180-PNEPSM4185-PNEPSM4190-PNEPSM4195-PNEPSM4200-PN
□□□□□□□□□□□□□□□●□□□□□□□□□●□□□□□□□□□●□□□□□□□●□□□□□□□●
9.259.39.359.49.459.59.559.69.659.79.759.89.859.99.951010.110.210.310.410.510.610.710.810.91111.111.211.311.411.511.611.711.811.91212.51313.51414.51515.51616.51717.51818.51919.520
23.323.323.523.523.823.8242424.324.324.524.524.824.8252525.325.525.82626.326.526.82727.327.527.82828.328.528.82929.329.529.83031.332.533.83536.337.538.84041.342.543.84546.347.548.850
10101010101010101010101010101010121212121212121212121212121212121212121216161616161616162020202020202020
747474747474747474747474747474748686868686868686868686868686868686868686105105105105110110110110120120120120125125125125
EPSM4 -PN Square type φ1~φ20
RL
φDcφDc φDsφDs
RL
20°
Regular EPSM4 -PN Square type φ1~φ20Regularφ1~φ6 φ6.05~φ20
0-0.015
0-0.02
EPSM
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAABAAAAAAAAAAAAAAAAAAABAAAAAAABAAAAAAAB
4 Flutes
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
Epoch Multi
Line Up
B typeA type
Helix 40°Carbide
CoatedUnequal
Pitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
1110
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
EPSM4010-PNEPSM40105-PNEPSM4011-PNEPSM40115-PNEPSM4012-PNEPSM40125-PNEPSM4013-PNEPSM40135-PNEPSM4014-PNEPSM40145-PNEPSM4015-PNEPSM40155-PNEPSM4016-PNEPSM40165-PNEPSM4017-PNEPSM40175-PNEPSM4018-PNEPSM40185-PNEPSM4019-PNEPSM40195-PNEPSM4020-PNEPSM40205-PNEPSM4021-PNEPSM40215-PNEPSM4022-PNEPSM40225-PNEPSM4023-PNEPSM40235-PNEPSM4024-PNEPSM40245-PNEPSM4025-PNEPSM40255-PNEPSM4026-PNEPSM40265-PNEPSM4027-PNEPSM40275-PNEPSM4028-PNEPSM40285-PNEPSM4029-PNEPSM40295-PNEPSM4030-PNEPSM40305-PNEPSM4031-PNEPSM40315-PNEPSM4032-PNEPSM40325-PNEPSM4033-PNEPSM40335-PNEPSM4034-PNEPSM40345-PNEPSM4035-PNEPSM40355-PNEPSM4036-PNEPSM40365-PNEPSM4037-PN
●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□
11.051.11.151.21.251.31.351.41.451.51.551.61.651.71.751.81.851.91.9522.052.12.152.22.252.32.352.42.452.52.552.62.652.72.752.82.852.92.9533.053.13.153.23.253.33.353.43.453.53.553.63.653.7
2.52.82.8333.33.33.53.53.83.8444.34.34.54.54.84.8555.35.35.55.55.85.8666.36.36.56.56.86.8777.37.37.57.57.87.8888.38.38.58.58.88.8999.39.3
6666666666666666666666666666666666666666666666666666666
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
56565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656
EPSM40375-PNEPSM4038-PNEPSM40385-PNEPSM4039-PNEPSM40395-PNEPSM4040-PNEPSM40405-PNEPSM4041-PNEPSM40415-PNEPSM4042-PNEPSM40425-PNEPSM4043-PNEPSM40435-PNEPSM4044-PNEPSM40445-PNEPSM4045-PNEPSM40455-PNEPSM4046-PNEPSM40465-PNEPSM4047-PNEPSM40475-PNEPSM4048-PNEPSM40485-PNEPSM4049-PNEPSM40495-PNEPSM4050-PNEPSM40505-PNEPSM4051-PNEPSM40515-PNEPSM4052-PNEPSM40525-PNEPSM4053-PNEPSM40535-PNEPSM4054-PNEPSM40545-PNEPSM4055-PNEPSM40555-PNEPSM4056-PNEPSM40565-PNEPSM4057-PNEPSM40575-PNEPSM4058-PNEPSM40585-PNEPSM4059-PNEPSM40595-PNEPSM4060-PNEPSM40605-PNEPSM4061-PNEPSM40615-PNEPSM4062-PNEPSM40625-PNEPSM4063-PNEPSM40635-PNEPSM4064-PNEPSM40645-PN
□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□
3.753.83.853.93.9544.054.14.154.24.254.34.354.44.454.54.554.64.654.74.754.84.854.94.9555.055.15.155.25.255.35.355.45.455.55.555.65.655.75.755.85.855.95.9566.056.16.156.26.256.36.356.46.45
9.5 9.5 9.8 9.8 10 10 10.3 10.3 10.5 10.5 10.8 10.8 11 11 11.3 11.3 11.5 11.5 11.8 11.8 12 12 12.3 12.3 12.5 12.5 12.8 12.8 13 13 13.3 13.3 13.5 13.5 13.8 13.8 14 14 14.3 14.3 14.5 14.5 14.8 14.8 15 15 15.3 15.3 15.5 15.5 15.8 15.8 16 16 16.3
6666666666666666666666666666666666666666666666888888888
56565656565656565656565656565656565656565656565656565656565656565656565656565656565656565656636363636363636363
EPSM4065-PNEPSM40655-PNEPSM4066-PNEPSM40665-PNEPSM4067-PNEPSM40675-PNEPSM4068-PNEPSM40685-PNEPSM4069-PNEPSM40695-PNEPSM4070-PNEPSM40705-PNEPSM4071-PNEPSM40715-PNEPSM4072-PNEPSM40725-PNEPSM4073-PNEPSM40735-PNEPSM4074-PNEPSM40745-PNEPSM4075-PNEPSM40755-PNEPSM4076-PNEPSM40765-PNEPSM4077-PNEPSM40775-PNEPSM4078-PNEPSM40785-PNEPSM4079-PNEPSM40795-PNEPSM4080-PNEPSM40805-PNEPSM4081-PNEPSM40815-PNEPSM4082-PNEPSM40825-PNEPSM4083-PNEPSM40835-PNEPSM4084-PNEPSM40845-PNEPSM4085-PNEPSM40855-PNEPSM4086-PNEPSM40865-PNEPSM4087-PNEPSM40875-PNEPSM4088-PNEPSM40885-PNEPSM4089-PNEPSM40895-PNEPSM4090-PNEPSM40905-PNEPSM4091-PNEPSM40915-PNEPSM4092-PN
□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□□□□□□□□□□□□□□□□●□□□□
6.56.556.66.656.76.756.86.856.96.9577.057.17.157.27.257.37.357.47.457.57.557.67.657.77.757.87.857.97.9588.058.18.158.28.258.38.358.48.458.58.558.68.658.78.758.88.858.98.9599.059.19.159.2
16.316.516.516.816.8171717.317.317.517.517.817.8181818.318.318.518.518.818.8191919.319.319.519.519.819.8202020.320.320.520.520.820.8212121.321.321.521.521.821.8222222.322.322.522.522.822.82323
8888888888888888888888888888888101010101010101010101010101010101010101010101010
63636363636363636363636363636363636363636363636363636363636363747474747474747474747474747474747474747474747474
EPSM40925-PNEPSM4093-PNEPSM40935-PNEPSM4094-PNEPSM40945-PNEPSM4095-PNEPSM40955-PNEPSM4096-PNEPSM40965-PNEPSM4097-PNEPSM40975-PNEPSM4098-PNEPSM40985-PNEPSM4099-PNEPSM40995-PNEPSM4100-PNEPSM4101-PNEPSM4102-PNEPSM4103-PNEPSM4104-PNEPSM4105-PNEPSM4106-PNEPSM4107-PNEPSM4108-PNEPSM4109-PNEPSM4110-PNEPSM4111-PNEPSM4112-PNEPSM4113-PNEPSM4114-PNEPSM4115-PNEPSM4116-PNEPSM4117-PNEPSM4118-PNEPSM4119-PNEPSM4120-PNEPSM4125-PNEPSM4130-PNEPSM4135-PNEPSM4140-PNEPSM4145-PNEPSM4150-PNEPSM4155-PNEPSM4160-PNEPSM4165-PNEPSM4170-PNEPSM4175-PNEPSM4180-PNEPSM4185-PNEPSM4190-PNEPSM4195-PNEPSM4200-PN
□□□□□□□□□□□□□□□●□□□□□□□□□●□□□□□□□□□●□□□□□□□●□□□□□□□●
9.259.39.359.49.459.59.559.69.659.79.759.89.859.99.951010.110.210.310.410.510.610.710.810.91111.111.211.311.411.511.611.711.811.91212.51313.51414.51515.51616.51717.51818.51919.520
23.323.323.523.523.823.8242424.324.324.524.524.824.8252525.325.525.82626.326.526.82727.327.527.82828.328.528.82929.329.529.83031.332.533.83536.337.538.84041.342.543.84546.347.548.850
10101010101010101010101010101010121212121212121212121212121212121212121216161616161616162020202020202020
747474747474747474747474747474748686868686868686868686868686868686868686105105105105110110110110120120120120125125125125
EPSM4 -PN Square type φ1~φ20
RL
φDcφDc φDsφDs
RL
20°
Regular EPSM4 -PN Square type φ1~φ20Regularφ1~φ6 φ6.05~φ20
0-0.015
0-0.02
EPSM
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAABAAAAAAAAAAAAAAAAAAABAAAAAAABAAAAAAAB
4 Flutes
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
Epoch Multi
Line Up
B typeA type
Helix 40°Carbide
CoatedUnequal
Pitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
1312
Epoch Multi
Item Code StockSize(mm)
Tool dia.Dc
Coner radiusr
Flute lengthR
Overall lengthL
Shank dia.Ds
No. of flutes ShapeItem Code Stock
Size(mm)Tool dia.
DcConer radius
rFlute length
ROverall length
LShank dia.
DsNo. of flutes Shape
EPSM4 -R . -PN Radius type φ1~φ20φ1~φ6 φ7~φ20
0-0.015
EPSM-CR
0-0.02
●:Stocked Items.
Regular EPSM4 -R . -PN Radius type φ1~φ20Regular
□:Stocked by specified distributor. Contact with our sales department.
EPSM4010-R0.1-PNEPSM4020-R0.1-PNEPSM4020-R0.2-PNEPSM4030-R0.2-PNEPSM4030-R0.5-PNEPSM4040-R0.2-PNEPSM4040-R0.5-PNEPSM4040-R1.0-PNEPSM4050-R0.2-PNEPSM4050-R0.5-PNEPSM4050-R1.0-PNEPSM4060-R0.3-PNEPSM4060-R0.5-PNEPSM4060-R1.0-PNEPSM4060-R1.5-PNEPSM4070-R0.3-PNEPSM4070-R0.5-PNEPSM4070-R1.0-PNEPSM4080-R0.3-PNEPSM4080-R0.5-PNEPSM4080-R1.0-PNEPSM4080-R1.5-PNEPSM4080-R2.0-PNEPSM4090-R0.3-PNEPSM4090-R0.5-PNEPSM4090-R1.0-PNEPSM4100-R0.3-PNEPSM4100-R0.5-PNEPSM4100-R1.0-PNEPSM4100-R1.5-PNEPSM4100-R2.0-PNEPSM4110-R0.3-PNEPSM4110-R0.5-PNEPSM4110-R1.0-PNEPSM4120-R0.3-PNEPSM4120-R0.5-PNEPSM4120-R1.0-PNEPSM4120-R1.5-PNEPSM4120-R2.0-PNEPSM4120-R2.5-PNEPSM4120-R3.0-PN
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
1
2
3
4
5
6
7
8
9
10
11
12
0.10.10.20.20.50.20.510.20.510.30.511.50.30.510.30.511.520.30.510.30.511.520.30.510.30.511.522.53
5656565656565656565656565656566363636363636363747474747474747486868686868686868686
66666666666666688888888101010101010101012121212121212121212
2.5 5 5 7.5 7.5 10 10 10 12.5 12.5 12.5 15 15 15 15 17.5 17.5 17.5 20 20 20 20 20 22.5 22.5 22.5 25 25 25 25 25 27.5 27.5 27.5 30 30 30 30 30 30 30
44444444444444444444444444444444444444444
AAAAAAAAAAABBBBAAABBBBBAAABBBBBAAABBBBBBB
EPSM4130-R0.5-PNEPSM4130-R1.0-PNEPSM4130-R1.5-PNEPSM4130-R2.0-PNEPSM4130-R3.0-PNEPSM4140-R0.5-PNEPSM4140-R1.0-PNEPSM4140-R1.5-PNEPSM4140-R2.0-PNEPSM4140-R3.0-PNEPSM4150-R0.5-PNEPSM4150-R1.0-PNEPSM4150-R1.5-PNEPSM4150-R2.0-PNEPSM4150-R3.0-PNEPSM4160-R0.5-PNEPSM4160-R1.0-PNEPSM4160-R1.5-PNEPSM4160-R2.0-PNEPSM4160-R3.0-PNEPSM4170-R0.5-PNEPSM4170-R1.0-PNEPSM4170-R1.5-PNEPSM4170-R2.0-PNEPSM4170-R3.0-PNEPSM4180-R0.5-PNEPSM4180-R1.0-PNEPSM4180-R1.5-PNEPSM4180-R2.0-PNEPSM4180-R3.0-PNEPSM4190-R0.5-PNEPSM4190-R1.0-PNEPSM4190-R1.5-PNEPSM4190-R2.0-PNEPSM4190-R3.0-PNEPSM4200-R0.5-PNEPSM4200-R1.0-PNEPSM4200-R1.5-PNEPSM4200-R2.0-PNEPSM4200-R3.0-PNEPSM4200-R5.0-PN
□□□□□□□□□□□□□□□●●●●●□□□□□□□□□□□□□□□●●●●●●
13
14
15
16
17
18
19
20
0.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5235
105105105105105105105105105105110110110110110110110110110110120120120120120120120120120120125125125125125125125125125125125
1616161616161616161616161616161616161616202020202020202020202020202020202020202020
32.532.532.532.532.5353535353537.537.537.537.537.5404040404042.542.542.542.542.5454545454547.547.547.547.547.5505050505050
44444444444444444444444444444444444444444
AAAAAAAAAAAAAAABBBBBAAAAAAAAAAAAAAABBBBBB
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
RL
φDcφDc φDsφDs
RL
20°
B typeA type
rr
Line Up
Helix 40°Carbide
CoatedUnequal
Pitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
1312
Epoch Multi
Item Code StockSize(mm)
Tool dia.Dc
Coner radiusr
Flute lengthR
Overall lengthL
Shank dia.Ds
No. of flutes ShapeItem Code Stock
Size(mm)Tool dia.
DcConer radius
rFlute length
ROverall length
LShank dia.
DsNo. of flutes Shape
EPSM4 -R . -PN Radius type φ1~φ20φ1~φ6 φ7~φ20
0-0.015
EPSM-CR
0-0.02
●:Stocked Items.
Regular EPSM4 -R . -PN Radius type φ1~φ20Regular
□:Stocked by specified distributor. Contact with our sales department.
EPSM4010-R0.1-PNEPSM4020-R0.1-PNEPSM4020-R0.2-PNEPSM4030-R0.2-PNEPSM4030-R0.5-PNEPSM4040-R0.2-PNEPSM4040-R0.5-PNEPSM4040-R1.0-PNEPSM4050-R0.2-PNEPSM4050-R0.5-PNEPSM4050-R1.0-PNEPSM4060-R0.3-PNEPSM4060-R0.5-PNEPSM4060-R1.0-PNEPSM4060-R1.5-PNEPSM4070-R0.3-PNEPSM4070-R0.5-PNEPSM4070-R1.0-PNEPSM4080-R0.3-PNEPSM4080-R0.5-PNEPSM4080-R1.0-PNEPSM4080-R1.5-PNEPSM4080-R2.0-PNEPSM4090-R0.3-PNEPSM4090-R0.5-PNEPSM4090-R1.0-PNEPSM4100-R0.3-PNEPSM4100-R0.5-PNEPSM4100-R1.0-PNEPSM4100-R1.5-PNEPSM4100-R2.0-PNEPSM4110-R0.3-PNEPSM4110-R0.5-PNEPSM4110-R1.0-PNEPSM4120-R0.3-PNEPSM4120-R0.5-PNEPSM4120-R1.0-PNEPSM4120-R1.5-PNEPSM4120-R2.0-PNEPSM4120-R2.5-PNEPSM4120-R3.0-PN
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
1
2
3
4
5
6
7
8
9
10
11
12
0.10.10.20.20.50.20.510.20.510.30.511.50.30.510.30.511.520.30.510.30.511.520.30.510.30.511.522.53
5656565656565656565656565656566363636363636363747474747474747486868686868686868686
66666666666666688888888101010101010101012121212121212121212
2.5 5 5 7.5 7.5 10 10 10 12.5 12.5 12.5 15 15 15 15 17.5 17.5 17.5 20 20 20 20 20 22.5 22.5 22.5 25 25 25 25 25 27.5 27.5 27.5 30 30 30 30 30 30 30
44444444444444444444444444444444444444444
AAAAAAAAAAABBBBAAABBBBBAAABBBBBAAABBBBBBB
EPSM4130-R0.5-PNEPSM4130-R1.0-PNEPSM4130-R1.5-PNEPSM4130-R2.0-PNEPSM4130-R3.0-PNEPSM4140-R0.5-PNEPSM4140-R1.0-PNEPSM4140-R1.5-PNEPSM4140-R2.0-PNEPSM4140-R3.0-PNEPSM4150-R0.5-PNEPSM4150-R1.0-PNEPSM4150-R1.5-PNEPSM4150-R2.0-PNEPSM4150-R3.0-PNEPSM4160-R0.5-PNEPSM4160-R1.0-PNEPSM4160-R1.5-PNEPSM4160-R2.0-PNEPSM4160-R3.0-PNEPSM4170-R0.5-PNEPSM4170-R1.0-PNEPSM4170-R1.5-PNEPSM4170-R2.0-PNEPSM4170-R3.0-PNEPSM4180-R0.5-PNEPSM4180-R1.0-PNEPSM4180-R1.5-PNEPSM4180-R2.0-PNEPSM4180-R3.0-PNEPSM4190-R0.5-PNEPSM4190-R1.0-PNEPSM4190-R1.5-PNEPSM4190-R2.0-PNEPSM4190-R3.0-PNEPSM4200-R0.5-PNEPSM4200-R1.0-PNEPSM4200-R1.5-PNEPSM4200-R2.0-PNEPSM4200-R3.0-PNEPSM4200-R5.0-PN
□□□□□□□□□□□□□□□●●●●●□□□□□□□□□□□□□□□●●●●●●
13
14
15
16
17
18
19
20
0.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5235
105105105105105105105105105105110110110110110110110110110110120120120120120120120120120120125125125125125125125125125125125
1616161616161616161616161616161616161616202020202020202020202020202020202020202020
32.532.532.532.532.5353535353537.537.537.537.537.5404040404042.542.542.542.542.5454545454547.547.547.547.547.5505050505050
44444444444444444444444444444444444444444
AAAAAAAAAAAAAAABBBBBAAAAAAAAAAAAAAABBBBBB
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
RL
φDcφDc φDsφDs
RL
20°
B typeA type
rr
Line Up
Helix 40°Carbide
CoatedUnequal
Pitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code StockSize (mm)
Tool dia.Dc
Flute lengthR
Under neck lengthR2
Neck dia.D1
Overall lengthL
Shank dia.Ds
No. of flutes Shape
Item Code
Size (mm)
Stock Tooldia.Dc
Cornerradius
r
FlutelengthR
Overall length
L
Shankdia.Ds
ShapeItem Code
Size (mm)
Stock Tooldia.Dc
Cornerradius
r
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
EPSMM4 -PN Medium Square type φ3~φ20φ3~φ6 φ7~φ20
0-0.015
0-0.02
EPSMM
RL
φDc φDsB type
EPSML4060-R0.3-PNEPSML4060-R0.5-PNEPSML4060-R1.0-PNEPSML4060-R1.5-PNEPSML4080-R0.3-PNEPSML4080-R0.5-PNEPSML4080-R1.0-PNEPSML4080-R1.5-PNEPSML4080-R2.0-PNEPSML4100-R0.3-PNEPSML4100-R0.5-PNEPSML4100-R1.0-PNEPSML4100-R1.5-PNEPSML4100-R2.0-PNEPSML4120-R0.3-PNEPSML4120-R0.5-PN
□□□□□□□□□□□□□□□□
6
8
10
12
0.30.511.50.30.511.520.30.511.520.30.5
707070708080808080100100100100100120120
66668888810101010101212
30303030404040404050505050506060
BBBBBBBBBBBBBBBB
EPSML4 -R . -PN Radius type φ6~φ20
r
φ6 φ8~φ20
0-0.015
EPSML-CR
0-0.02
Long
EPSML4 -PN Long Square type φ6~φ20φ6 φ7~φ20
0-0.015
0-0.02
EPSML
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
EPSML4060-PNEPSML4070-PNEPSML4080-PNEPSML4090-PNEPSML4100-PNEPSML4110-PNEPSML4120-PNEPSML4130-PN
●□●□●□●□
6789
10111213
3035404550556065
6881010121216
BABABABA
708080100100120120130
EPSML4140-PNEPSML4150-PNEPSML4160-PNEPSML4170-PNEPSML4180-PNEPSML4190-PNEPSML4200-PN
□□●□□□●
14151617181920
707580859095
100
16161620202020
AABAAAB
130130135135145145155
EPSML4120-R1.0-PNEPSML4120-R1.5-PNEPSML4120-R2.0-PNEPSML4120-R2.5-PNEPSML4120-R3.0-PNEPSML4160-R0.5-PNEPSML4160-R1.0-PNEPSML4160-R1.5-PNEPSML4160-R2.0-PNEPSML4160-R3.0-PNEPSML4200-R0.5-PNEPSML4200-R1.0-PNEPSML4200-R1.5-PNEPSML4200-R2.0-PNEPSML4200-R3.0-PNEPSML4200-R5.0-PN
□□□□□□□□□□□□□□□□
12
16
20
11.522.530.511.5230.511.5235
120120120120120135135135135135155155155155155155
12121212121616161616202020202020
60606060608080808080
100100100100100100
BBBBBBBBBBBBBBBB
EPSMLS4 -PN Long shank Square type φ3~φ17φ3~φ6 φ7~φ17
0-0.015
EPSMLS
0-0.02
4 Flutes
4 Flutes
4 Flutes
EPSMM4030-PNEPSMM4040-PNEPSMM4050-PNEPSMM4060-PNEPSMM4070-PNEPSMM4080-PN
●●●●●●
345678
121620242832
666688
AAABAB
565670707580
EPSMM4090-PNEPSMM4100-PNEPSMM4110-PNEPSMM4120-PNEPSMM4160-PNEPSMM4200-PN
●●●●●●
91011121620
364044486480
101012121620
ABABBB
100100120120135155
EPSMLS4030-PN EPSMLS4040-PN EPSMLS4050-PN EPSMLS4060-PN EPSMLS4070-PN EPSMLS4080-PN EPSMLS4090-PN EPSMLS4100-PN EPSMLS4110-PN EPSMLS4120-PN EPSMLS4130-PN EPSMLS4160-PN EPSMLS4170-PN
●●●●●●●●●●●●●
3456789
101112131617
4.5 6 7.5 9 9 12 12 15 15 18 18 24 24
2.883.74.6 - - - - - - - - - -
8080
100120120135135150150160160180180
66656789
1011121516
10.51417.5 - - - - - - - - - -
4444444444444
AAABBBBBBBBBB
4 FlutesR
L
φDc φDsB type
A type
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
φDc φDs
RR2
L
20°
φD
1
1514
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
φDc:3~5 φDc:6~17
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26
Epoch Multi Epoch Multi
Epoch Multi
Epoch Multi
Helix 40°Carbide
Coated
Helix 40°Carbide
Coated
Helix 40°Carbide
Coated
Helix 40°Carbide
CoatedUnequal
Pitch
UnequalPitch
UnequalPitch
UnequalPitch
Line Up
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code StockSize (mm)
Tool dia.Dc
Flute lengthR
Under neck lengthR2
Neck dia.D1
Overall lengthL
Shank dia.Ds
No. of flutes Shape
Item Code
Size (mm)
Stock Tooldia.Dc
Cornerradius
r
FlutelengthR
Overall length
L
Shankdia.Ds
ShapeItem Code
Size (mm)
Stock Tooldia.Dc
Cornerradius
r
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
Item Code Stock Tooldia.Dc
FlutelengthR
Overall length
L
Shankdia.Ds
Shape
Size (mm)
EPSMM4 -PN Medium Square type φ3~φ20φ3~φ6 φ7~φ20
0-0.015
0-0.02
EPSMM
RL
φDc φDsB type
EPSML4060-R0.3-PNEPSML4060-R0.5-PNEPSML4060-R1.0-PNEPSML4060-R1.5-PNEPSML4080-R0.3-PNEPSML4080-R0.5-PNEPSML4080-R1.0-PNEPSML4080-R1.5-PNEPSML4080-R2.0-PNEPSML4100-R0.3-PNEPSML4100-R0.5-PNEPSML4100-R1.0-PNEPSML4100-R1.5-PNEPSML4100-R2.0-PNEPSML4120-R0.3-PNEPSML4120-R0.5-PN
□□□□□□□□□□□□□□□□
6
8
10
12
0.30.511.50.30.511.520.30.511.520.30.5
707070708080808080100100100100100120120
66668888810101010101212
30303030404040404050505050506060
BBBBBBBBBBBBBBBB
EPSML4 -R . -PN Radius type φ6~φ20
r
φ6 φ8~φ20
0-0.015
EPSML-CR
0-0.02
Long
EPSML4 -PN Long Square type φ6~φ20φ6 φ7~φ20
0-0.015
0-0.02
EPSML
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
EPSML4060-PNEPSML4070-PNEPSML4080-PNEPSML4090-PNEPSML4100-PNEPSML4110-PNEPSML4120-PNEPSML4130-PN
●□●□●□●□
6789
10111213
3035404550556065
6881010121216
BABABABA
708080100100120120130
EPSML4140-PNEPSML4150-PNEPSML4160-PNEPSML4170-PNEPSML4180-PNEPSML4190-PNEPSML4200-PN
□□●□□□●
14151617181920
707580859095
100
16161620202020
AABAAAB
130130135135145145155
EPSML4120-R1.0-PNEPSML4120-R1.5-PNEPSML4120-R2.0-PNEPSML4120-R2.5-PNEPSML4120-R3.0-PNEPSML4160-R0.5-PNEPSML4160-R1.0-PNEPSML4160-R1.5-PNEPSML4160-R2.0-PNEPSML4160-R3.0-PNEPSML4200-R0.5-PNEPSML4200-R1.0-PNEPSML4200-R1.5-PNEPSML4200-R2.0-PNEPSML4200-R3.0-PNEPSML4200-R5.0-PN
□□□□□□□□□□□□□□□□
12
16
20
11.522.530.511.5230.511.5235
120120120120120135135135135135155155155155155155
12121212121616161616202020202020
60606060608080808080
100100100100100100
BBBBBBBBBBBBBBBB
EPSMLS4 -PN Long shank Square type φ3~φ17φ3~φ6 φ7~φ17
0-0.015
EPSMLS
0-0.02
4 Flutes
4 Flutes
4 Flutes
EPSMM4030-PNEPSMM4040-PNEPSMM4050-PNEPSMM4060-PNEPSMM4070-PNEPSMM4080-PN
●●●●●●
345678
121620242832
666688
AAABAB
565670707580
EPSMM4090-PNEPSMM4100-PNEPSMM4110-PNEPSMM4120-PNEPSMM4160-PNEPSMM4200-PN
●●●●●●
91011121620
364044486480
101012121620
ABABBB
100100120120135155
EPSMLS4030-PN EPSMLS4040-PN EPSMLS4050-PN EPSMLS4060-PN EPSMLS4070-PN EPSMLS4080-PN EPSMLS4090-PN EPSMLS4100-PN EPSMLS4110-PN EPSMLS4120-PN EPSMLS4130-PN EPSMLS4160-PN EPSMLS4170-PN
●●●●●●●●●●●●●
3456789
101112131617
4.5 6 7.5 9 9 12 12 15 15 18 18 24 24
2.883.74.6 - - - - - - - - - -
8080
100120120135135150150160160180180
66656789
1011121516
10.51417.5 - - - - - - - - - -
4444444444444
AAABBBBBBBBBB
4 FlutesR
L
φDc φDsB type
A type
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
φDc φDs
RR2
L
20°
φD
1
1514
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
φDc:3~5 φDc:6~17
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26
Epoch Multi Epoch Multi
Epoch Multi
Epoch Multi
Helix 40°Carbide
Coated
Helix 40°Carbide
Coated
Helix 40°Carbide
Coated
Helix 40°Carbide
CoatedUnequal
Pitch
UnequalPitch
UnequalPitch
UnequalPitch
Line UpD
imensions,
SU
S M
ultiD
imensions,
SU
S Finish
Dim
ensions,S
US
Wave
FeaturesC
utting conditionR
e-grindingTechnical D
ata
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape
EPSM4 - -PN.
EPSM4010-5-PNEPSM4015-7.5-PNEPSM4020-10-PNEPSM4025-12.5-PNEPSM4030-15-PNEPSM4035-17.5-PNEPSM4040-20-PNEPSM4045-22.5-PNEPSM4050-25-PNEPSM4055-27.5-PNEPSM4060-30-PNEPSM4065-32.5-PNEPSM4070-35-PNEPSM4075-37.5-PNEPSM4080-40-PNEPSM4085-42.5-PNEPSM4090-45-PNEPSM4095-47.5-PNEPSM4100-50-PNEPSM4105-52.5-PNEPSM4110-55-PNEPSM4115-57.5-PNEPSM4120-60-PNEPSM4130-65-PNEPSM4140-70-PNEPSM4150-75-PNEPSM4160-80-PNEPSM4170-85-PNEPSM4180-90-PNEPSM4190-95-PNEPSM4200-100-PN
●□●□●□●□●□●□●□●□●□●□●□●□□□●□□□●
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
0.96 1.44 1.92 2.4 2.88 3.35 3.7 4.15 4.6 5.05 5.5 5.95 6.4 6.85 7.3 7.8 8.3 8.7 9.1 9.65 10.2 10.6 11 11.7 12.7 13.6 14.5 15.4 16.3 17.3 18.2
68686868686868686868688080808094949494
110110110110125125135135145145155155
666666666668888
10101010121212121616161620202020
5 7.5 10 12.5 15 17.5 20 22.5 25 27.5 30 32.5 35 37.5 40 42.5 45 47.5 50 52.5 55 57.5 60 65 70 75 80 85 90 95 100
4444444444444444444444444444444
AAAAAAAAAABAAABAAABAAABAAABAAAB
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
φ1~6 φ6.5~φ20
0-0.015
0-0.02
1.5 2.3 3 3.8 4.5 5.3 6 6.8 7.5 8.3 9 9.8 10.5 11.3 12 12.8 13.5 14.3 15 15.8 16.5 17.3 18 19.5 21 22.5 24 25.5 27 28.5 30
EPSM4010-3-PNEPSM4015-4.5-PNEPSM4020-6-PNEPSM4025-7.5-PNEPSM4030-9-PNEPSM4035-10.5-PNEPSM4040-12-PNEPSM4045-13.5-PNEPSM4050-15-PNEPSM4055-16.5-PNEPSM4060-18-PNEPSM4065-19.5-PNEPSM4070-21-PNEPSM4075-22.5-PNEPSM4080-24-PNEPSM4085-25.5-PNEPSM4090-27-PNEPSM4095-28.5-PNEPSM4100-30-PNEPSM4105-31.5-PNEPSM4110-33-PNEPSM4115-34.5-PNEPSM4120-36-PNEPSM4130-39-PNEPSM4140-42-PNEPSM4150-45-PNEPSM4160-48-PNEPSM4170-51-PNEPSM4180-54-PNEPSM4190-57-PNEPSM4200-60-PN
●□●□●□●□●□●□●□●□●□●□●□●□□□●□□□●
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
1.5 2.3 3 3.8 4.5 5.3 6 6.8 7.5 8.3 9 9.8 10.5 11.3 12 12.8 13.5 14.3 15 15.8 16.5 17.3 18 19.5 21 22.5 24 25.5 27 28.5 30
0.96 1.44 1.92 2.4 2.88 3.35 3.7 4.15 4.6 5.05 5.5 5.95 6.4 6.85 7.3 7.8 8.3 8.7 9.1 9.65 10.2 10.6 11 11.7 12.7 13.6 14.5 15.4 16.3 17.3 18.2
5656565656565656565656636363637474747486868686
105105110110120120125125
666666666668888
10101010121212121616161620202020
3 4.5 6 7.5 9 10.5 12 13.5 15 16.5 18 19.5 21 22.5 24 25.5 27 28.5 30 31.5 33 34.5 36 39 42 45 48 51 54 57 60
4444444444444444444444444444444
AAAAAAAAAABAAABAAABAAABAAABAAAB
EPSM4 - -PN.
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
φ1~φ6 φ6.5~φ20
0-0.015
0-0.02
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.1716
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.27Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
L ine Up
EPSMEpoch Multi EPSMEpoch Multi
Under neck 3Dc Square type φ1~φ20 Under neck 5Dc Square type φ1~φ20Helix 40°
CarbideCoated
Helix 40°Carbide
CoatedUnequal
PitchUnequal
Pitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape
EPSM4 - -PN.
EPSM4010-5-PNEPSM4015-7.5-PNEPSM4020-10-PNEPSM4025-12.5-PNEPSM4030-15-PNEPSM4035-17.5-PNEPSM4040-20-PNEPSM4045-22.5-PNEPSM4050-25-PNEPSM4055-27.5-PNEPSM4060-30-PNEPSM4065-32.5-PNEPSM4070-35-PNEPSM4075-37.5-PNEPSM4080-40-PNEPSM4085-42.5-PNEPSM4090-45-PNEPSM4095-47.5-PNEPSM4100-50-PNEPSM4105-52.5-PNEPSM4110-55-PNEPSM4115-57.5-PNEPSM4120-60-PNEPSM4130-65-PNEPSM4140-70-PNEPSM4150-75-PNEPSM4160-80-PNEPSM4170-85-PNEPSM4180-90-PNEPSM4190-95-PNEPSM4200-100-PN
●□●□●□●□●□●□●□●□●□●□●□●□□□●□□□●
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
0.96 1.44 1.92 2.4 2.88 3.35 3.7 4.15 4.6 5.05 5.5 5.95 6.4 6.85 7.3 7.8 8.3 8.7 9.1 9.65 10.2 10.6 11 11.7 12.7 13.6 14.5 15.4 16.3 17.3 18.2
68686868686868686868688080808094949494
110110110110125125135135145145155155
666666666668888
10101010121212121616161620202020
5 7.5 10 12.5 15 17.5 20 22.5 25 27.5 30 32.5 35 37.5 40 42.5 45 47.5 50 52.5 55 57.5 60 65 70 75 80 85 90 95 100
4444444444444444444444444444444
AAAAAAAAAABAAABAAABAAABAAABAAAB
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
φ1~6 φ6.5~φ20
0-0.015
0-0.02
1.5 2.3 3 3.8 4.5 5.3 6 6.8 7.5 8.3 9 9.8 10.5 11.3 12 12.8 13.5 14.3 15 15.8 16.5 17.3 18 19.5 21 22.5 24 25.5 27 28.5 30
EPSM4010-3-PNEPSM4015-4.5-PNEPSM4020-6-PNEPSM4025-7.5-PNEPSM4030-9-PNEPSM4035-10.5-PNEPSM4040-12-PNEPSM4045-13.5-PNEPSM4050-15-PNEPSM4055-16.5-PNEPSM4060-18-PNEPSM4065-19.5-PNEPSM4070-21-PNEPSM4075-22.5-PNEPSM4080-24-PNEPSM4085-25.5-PNEPSM4090-27-PNEPSM4095-28.5-PNEPSM4100-30-PNEPSM4105-31.5-PNEPSM4110-33-PNEPSM4115-34.5-PNEPSM4120-36-PNEPSM4130-39-PNEPSM4140-42-PNEPSM4150-45-PNEPSM4160-48-PNEPSM4170-51-PNEPSM4180-54-PNEPSM4190-57-PNEPSM4200-60-PN
●□●□●□●□●□●□●□●□●□●□●□●□□□●□□□●
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
1.5 2.3 3 3.8 4.5 5.3 6 6.8 7.5 8.3 9 9.8 10.5 11.3 12 12.8 13.5 14.3 15 15.8 16.5 17.3 18 19.5 21 22.5 24 25.5 27 28.5 30
0.96 1.44 1.92 2.4 2.88 3.35 3.7 4.15 4.6 5.05 5.5 5.95 6.4 6.85 7.3 7.8 8.3 8.7 9.1 9.65 10.2 10.6 11 11.7 12.7 13.6 14.5 15.4 16.3 17.3 18.2
5656565656565656565656636363637474747486868686
105105110110120120125125
666666666668888
10101010121212121616161620202020
3 4.5 6 7.5 9 10.5 12 13.5 15 16.5 18 19.5 21 22.5 24 25.5 27 28.5 30 31.5 33 34.5 36 39 42 45 48 51 54 57 60
4444444444444444444444444444444
AAAAAAAAAABAAABAAABAAABAAABAAAB
EPSM4 - -PN.
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
φ1~φ6 φ6.5~φ20
0-0.015
0-0.02
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.1716
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23High speed Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・P.24General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.27Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
L ine Up
EPSMEpoch Multi EPSMEpoch Multi
Under neck 3Dc Square type φ1~φ20 Under neck 5Dc Square type φ1~φ20Helix 40°
CarbideCoated
Helix 40°Carbide
CoatedUnequal
PitchUnequal
Pitch
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
1918
Item Code StockSize (mm)
Tool dia.
Dc
Flute length
R
Conerradius
r
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Conerradius
r
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
EPSM4 - -PN-R .
r
r
φ1~φ6 φ7~φ20
0-0.015
0-0.02
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
EPSM4010-5-R0.1-PNEPSM4020-10-R0.1-PNEPSM4020-10-R0.2-PNEPSM4030-15-R0.2-PNEPSM4030-15-R0.5-PNEPSM4040-20-R0.2-PNEPSM4040-20-R0.5-PNEPSM4040-20-R1.0-PNEPSM4050-25-R0.2-PNEPSM4050-25-R0.5-PNEPSM4050-25-R1.0-PNEPSM4060-30-R0.3-PNEPSM4060-30-R0.5-PNEPSM4060-30-R1.0-PNEPSM4060-30-R1.5-PNEPSM4070-35-R0.3-PNEPSM4070-35-R0.5-PNEPSM4070-35-R1.0-PNEPSM4080-40-R0.3-PNEPSM4080-40-R0.5-PNEPSM4080-40-R1.0-PNEPSM4080-40-R1.5-PNEPSM4080-40-R2.0-PNEPSM4090-45-R0.3-PNEPSM4090-45-R0.5-PNEPSM4090-45-R1.0-PNEPSM4100-50-R0.3-PNEPSM4100-50-R0.5-PNEPSM4100-50-R1.0-PNEPSM4100-50-R1.5-PNEPSM4100-50-R2.0-PNEPSM4110-55-R0.3-PNEPSM4110-55-R0.5-PNEPSM4110-55-R1.0-PNEPSM4120-60-R0.3-PNEPSM4120-60-R0.5-PNEPSM4120-60-R1.0-PNEPSM4120-60-R1.5-PNEPSM4120-60-R2.0-PNEPSM4120-60-R2.5-PNEPSM4120-60-R3.0-PN
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
1
2
3
4
5
6
7
8
9
10
11
12
0.96 1.92 1.92 2.88 2.88 3.7 3.7 3.7 4.6 4.6 4.6 5.5 5.5 5.5 5.5 6.4 6.4 6.4 7.3 7.3 7.3 7.3 7.3 8.3 8.3 8.3 9.1 9.1 9.1 9.1 9.1 10.2 10.2 10.2 11 11 11 11 11 11 11
68686868686868686868686868686880808080808080809494949494949494
110110110110110110110110110110
66666666666666688888888
101010101010101012121212121212121212
510101515202020252525303030303535354040404040454545505050505055555560606060606060
44444444444444444444444444444444444444444
AAAAAAAAAAABBBBAAABBBBBAAABBBBBAAABBBBBBB
1.5 3 3 4.5 4.5 6 6 6 7.5 7.5 7.5 9 9 9 9 10.5 10.5 10.5 12 12 12 12 12 13.5 13.5 13.5 15 15 15 15 15 16.5 16.5 16.5 18 18 18 18 18 18 18
0.10.10.20.20.50.20.510.20.510.30.511.50.30.510.30.511.520.30.510.30.511.520.30.510.30.511.522.53
□□□□□□□□□□□□□□□●●●●●□□□□□□□□□□□□□□□●●●●●●
13
14
15
16
17
18
19
20
11.711.711.711.711.712.712.712.712.712.713.613.613.613.613.614.514.514.514.514.515.415.415.415.415.416.316.316.316.316.317.317.317.317.317.318.218.218.218.218.218.2
125125125125125125125125125125135135135135135135135135135135145145145145145145145145145145155155155155155155155155155155155
1616161616161616161616161616161616161616202020202020202020202020202020202020202020
6565656565707070707075757575758080808080858585858590909090909595959595
100100100100100100
44444444444444444444444444444444444444444
AAAAAAAAAAAAAAABBBBBAAAAAAAAAAAAAAABBBBBB
19.519.519.519.519.5212121212122.522.522.522.522.5242424242425.525.525.525.525.5272727272728.528.528.528.528.5303030303030
0.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5235
EPSM4130-65-R0.5-PNEPSM4130-65-R1.0-PNEPSM4130-65-R1.5-PNEPSM4130-65-R2.0-PNEPSM4130-65-R3.0-PNEPSM4140-70-R0.5-PNEPSM4140-70-R1.0-PNEPSM4140-70-R1.5-PNEPSM4140-70-R2.0-PNEPSM4140-70-R3.0-PNEPSM4150-75-R0.5-PNEPSM4150-75-R1.0-PNEPSM4150-75-R1.5-PNEPSM4150-75-R2.0-PNEPSM4150-75-R3.0-PNEPSM4160-80-R0.5-PNEPSM4160-80-R1.0-PNEPSM4160-80-R1.5-PNEPSM4160-80-R2.0-PNEPSM4160-80-R3.0-PNEPSM4170-85-R0.5-PNEPSM4170-85-R1.0-PNEPSM4170-85-R1.5-PNEPSM4170-85-R2.0-PNEPSM4170-85-R3.0-PNEPSM4180-90-R0.5-PNEPSM4180-90-R1.0-PNEPSM4180-90-R1.5-PNEPSM4180-90-R2.0-PNEPSM4180-90-R3.0-PNEPSM4190-95-R0.5-PNEPSM4190-95-R1.0-PNEPSM4190-95-R1.5-PNEPSM4190-95-R2.0-PNEPSM4190-95-R3.0-PNEPSM4200-100-R0.5-PNEPSM4200-100-R1.0-PNEPSM4200-100-R1.5-PNEPSM4200-100-R2.0-PNEPSM4200-100-R3.0-PNEPSM4200-100-R5.0-PN
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.27Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
L ine Up
EPSM-CREpoch Multi
Helix 40°Carbide
CoatedUnequal
PitchRadius type φ1~φ20Under neck 5Dc EPSM4 - -PN-R . Radius type
φ1~φ20Under neck 5Dc
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
1918
Item Code StockSize (mm)
Tool dia.
Dc
Flute length
R
Conerradius
r
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Conerradius
r
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes Shape
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
EPSM4 - -PN-R .
r
r
φ1~φ6 φ7~φ20
0-0.015
0-0.02
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
EPSM4010-5-R0.1-PNEPSM4020-10-R0.1-PNEPSM4020-10-R0.2-PNEPSM4030-15-R0.2-PNEPSM4030-15-R0.5-PNEPSM4040-20-R0.2-PNEPSM4040-20-R0.5-PNEPSM4040-20-R1.0-PNEPSM4050-25-R0.2-PNEPSM4050-25-R0.5-PNEPSM4050-25-R1.0-PNEPSM4060-30-R0.3-PNEPSM4060-30-R0.5-PNEPSM4060-30-R1.0-PNEPSM4060-30-R1.5-PNEPSM4070-35-R0.3-PNEPSM4070-35-R0.5-PNEPSM4070-35-R1.0-PNEPSM4080-40-R0.3-PNEPSM4080-40-R0.5-PNEPSM4080-40-R1.0-PNEPSM4080-40-R1.5-PNEPSM4080-40-R2.0-PNEPSM4090-45-R0.3-PNEPSM4090-45-R0.5-PNEPSM4090-45-R1.0-PNEPSM4100-50-R0.3-PNEPSM4100-50-R0.5-PNEPSM4100-50-R1.0-PNEPSM4100-50-R1.5-PNEPSM4100-50-R2.0-PNEPSM4110-55-R0.3-PNEPSM4110-55-R0.5-PNEPSM4110-55-R1.0-PNEPSM4120-60-R0.3-PNEPSM4120-60-R0.5-PNEPSM4120-60-R1.0-PNEPSM4120-60-R1.5-PNEPSM4120-60-R2.0-PNEPSM4120-60-R2.5-PNEPSM4120-60-R3.0-PN
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
1
2
3
4
5
6
7
8
9
10
11
12
0.96 1.92 1.92 2.88 2.88 3.7 3.7 3.7 4.6 4.6 4.6 5.5 5.5 5.5 5.5 6.4 6.4 6.4 7.3 7.3 7.3 7.3 7.3 8.3 8.3 8.3 9.1 9.1 9.1 9.1 9.1 10.2 10.2 10.2 11 11 11 11 11 11 11
68686868686868686868686868686880808080808080809494949494949494
110110110110110110110110110110
66666666666666688888888
101010101010101012121212121212121212
510101515202020252525303030303535354040404040454545505050505055555560606060606060
44444444444444444444444444444444444444444
AAAAAAAAAAABBBBAAABBBBBAAABBBBBAAABBBBBBB
1.5 3 3 4.5 4.5 6 6 6 7.5 7.5 7.5 9 9 9 9 10.5 10.5 10.5 12 12 12 12 12 13.5 13.5 13.5 15 15 15 15 15 16.5 16.5 16.5 18 18 18 18 18 18 18
0.10.10.20.20.50.20.510.20.510.30.511.50.30.510.30.511.520.30.510.30.511.520.30.510.30.511.522.53
□□□□□□□□□□□□□□□●●●●●□□□□□□□□□□□□□□□●●●●●●
13
14
15
16
17
18
19
20
11.711.711.711.711.712.712.712.712.712.713.613.613.613.613.614.514.514.514.514.515.415.415.415.415.416.316.316.316.316.317.317.317.317.317.318.218.218.218.218.218.2
125125125125125125125125125125135135135135135135135135135135145145145145145145145145145145155155155155155155155155155155155
1616161616161616161616161616161616161616202020202020202020202020202020202020202020
6565656565707070707075757575758080808080858585858590909090909595959595
100100100100100100
44444444444444444444444444444444444444444
AAAAAAAAAAAAAAABBBBBAAAAAAAAAAAAAAABBBBBB
19.519.519.519.519.5212121212122.522.522.522.522.5242424242425.525.525.525.525.5272727272728.528.528.528.528.5303030303030
0.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5230.511.5235
EPSM4130-65-R0.5-PNEPSM4130-65-R1.0-PNEPSM4130-65-R1.5-PNEPSM4130-65-R2.0-PNEPSM4130-65-R3.0-PNEPSM4140-70-R0.5-PNEPSM4140-70-R1.0-PNEPSM4140-70-R1.5-PNEPSM4140-70-R2.0-PNEPSM4140-70-R3.0-PNEPSM4150-75-R0.5-PNEPSM4150-75-R1.0-PNEPSM4150-75-R1.5-PNEPSM4150-75-R2.0-PNEPSM4150-75-R3.0-PNEPSM4160-80-R0.5-PNEPSM4160-80-R1.0-PNEPSM4160-80-R1.5-PNEPSM4160-80-R2.0-PNEPSM4160-80-R3.0-PNEPSM4170-85-R0.5-PNEPSM4170-85-R1.0-PNEPSM4170-85-R1.5-PNEPSM4170-85-R2.0-PNEPSM4170-85-R3.0-PNEPSM4180-90-R0.5-PNEPSM4180-90-R1.0-PNEPSM4180-90-R1.5-PNEPSM4180-90-R2.0-PNEPSM4180-90-R3.0-PNEPSM4190-95-R0.5-PNEPSM4190-95-R1.0-PNEPSM4190-95-R1.5-PNEPSM4190-95-R2.0-PNEPSM4190-95-R3.0-PNEPSM4200-100-R0.5-PNEPSM4200-100-R1.0-PNEPSM4200-100-R1.5-PNEPSM4200-100-R2.0-PNEPSM4200-100-R3.0-PNEPSM4200-100-R5.0-PN
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.27Side finishing conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.30
L ine Up
EPSM-CREpoch Multi
Helix 40°Carbide
CoatedUnequal
PitchRadius type φ1~φ20Under neck 5Dc EPSM4 - -PN-R . Radius type
φ1~φ20Under neck 5Dc
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock
Size (mm)
Tool dia.
Dc
Flute length
R
Overalllength
L
Shank dia.
Ds
No. of flutes ShapeCorner
chamferingwidth
Item Code Stock
Size (mm)
Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes
Cornerchamfering
width
Shape
Item Code Stock
Size (mm)
Tool dia.
Dc
Flute length
R
Overalllength
L
Shank dia.
Ds
No. of flutes ShapeCorner
chamferingwidth
EPSW -PN
EPSW3040-PNEPSW3045-PNEPSW3050-PNEPSW3055-PNEPSW4060-PNEPSW4065-PNEPSW4070-PNEPSW4075-PNEPSW4080-PNEPSW4085-PNEPSW4090-PNEPSW4095-PNEPSW4100-PNEPSW4105-PNEPSW4110-PNEPSW4115-PNEPSW4120-PNEPSW4130-PNEPSW4140-PNEPSW4150-PNEPSW4160-PNEPSW4170-PNEPSW4180-PNEPSW4190-PNEPSW4200-PN
●□●□●□●□●□●□●□●□●□□□●□□□●
4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
1011.312.513.81516.317.518.82021.322.523.82526.327.528.83032.53537.54042.54547.550
5656565656636363637474747486868686
105105110110120120125125
666668888
10101010121212121616161620202020
3333444444444444444444444
AAAABAAABAAABAAABAAABAAAB
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
0.30.30.30.30.40.40.40.40.50.50.50.50.50.50.50.50.50.70.70.70.70.70.70.70.7
0-0.05
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
EPSWL -PN 0-0.05
EPSWL4060-PNEPSWL4070-PNEPSWL4080-PNEPSWL4090-PNEPSWL4100-PNEPSWL4110-PNEPSWL4120-PNEPSWL4130-PNEPSWL4140-PNEPSWL4150-PNEPSWL4160-PNEPSWL4170-PNEPSWL4180-PNEPSWL4190-PNEPSWL4200-PN
●□●□●□●□□□●□□□●
6789
1011121314151617181920
3035404550556065707580859095
100
708080
100100120120130130130135135145145155
688
101012121616161620202020
0.40.40.50.50.50.50.50.70.70.70.70.70.70.70.7
444444444444444
BABABABAAABAAAB
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
2120
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
EPSW3040-12-PNEPSW3050-15-PNEPSW4060-18-PNEPSW4070-21-PNEPSW4080-24-PNEPSW4090-27-PNEPSW4100-30-PNEPSW4110-33-PNEPSW4120-36-PNEPSW4160-48-PNEPSW4200-60-PN
●●●●●●●●●●●
456789
1011121620
6 7.5 9 10.5 12 13.5 15 16.5 18 24 30
3.7 4.6 5.5 6.4 7.3 8.3 9.1 10.2 11 14.5 18.2
565656636374748686
110125
66688
101012121620
0.30.30.40.40.50.50.50.50.50.70.7
1215182124273033364860
33444444444
AABABABABBB
EPSW - -PN
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
0-0.05
EPSW
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28EPSWEpoch Wave
Line Up
Roughing type φ4~φ20RegularHelix 30°
CarbideCoated
Helix 30°Carbide
CoatedUnequal
Pitch
UnequalPitch
UnequalPitch
Helix 30°Carbide
Coated
EPSWLEpoch Wave
Epoch Wave
Roughing type φ6~φ20Long
Roughing type φ4~φ20Under neck 3Dc
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock
Size (mm)
Tool dia.
Dc
Flute length
R
Overalllength
L
Shank dia.
Ds
No. of flutes ShapeCorner
chamferingwidth
Item Code Stock
Size (mm)
Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes
Cornerchamfering
width
Shape
Item Code Stock
Size (mm)
Tool dia.
Dc
Flute length
R
Overalllength
L
Shank dia.
Ds
No. of flutes ShapeCorner
chamferingwidth
EPSW -PN
EPSW3040-PNEPSW3045-PNEPSW3050-PNEPSW3055-PNEPSW4060-PNEPSW4065-PNEPSW4070-PNEPSW4075-PNEPSW4080-PNEPSW4085-PNEPSW4090-PNEPSW4095-PNEPSW4100-PNEPSW4105-PNEPSW4110-PNEPSW4115-PNEPSW4120-PNEPSW4130-PNEPSW4140-PNEPSW4150-PNEPSW4160-PNEPSW4170-PNEPSW4180-PNEPSW4190-PNEPSW4200-PN
●□●□●□●□●□●□●□●□●□□□●□□□●
4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
1011.312.513.81516.317.518.82021.322.523.82526.327.528.83032.53537.54042.54547.550
5656565656636363637474747486868686
105105110110120120125125
666668888
10101010121212121616161620202020
3333444444444444444444444
AAAABAAABAAABAAABAAABAAAB
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
0.30.30.30.30.40.40.40.40.50.50.50.50.50.50.50.50.50.70.70.70.70.70.70.70.7
0-0.05
●:Stocked Items. □:Stocked by specified distributor. Contact with our sales department.
EPSWL -PN 0-0.05
EPSWL4060-PNEPSWL4070-PNEPSWL4080-PNEPSWL4090-PNEPSWL4100-PNEPSWL4110-PNEPSWL4120-PNEPSWL4130-PNEPSWL4140-PNEPSWL4150-PNEPSWL4160-PNEPSWL4170-PNEPSWL4180-PNEPSWL4190-PNEPSWL4200-PN
●□●□●□●□□□●□□□●
6789
1011121314151617181920
3035404550556065707580859095
100
708080
100100120120130130130135135145145155
688
101012121616161620202020
0.40.40.50.50.50.50.50.70.70.70.70.70.70.70.7
444444444444444
BABABABAAABAAAB
RL
φDc
φDc
φDs
φDs
RL
20°
B type
A type
2120
φ6~φ12 φ16,φ20
h5 h6
φ6~φ12 φ16,φ20
h5 h6
EPSW3040-12-PNEPSW3050-15-PNEPSW4060-18-PNEPSW4070-21-PNEPSW4080-24-PNEPSW4090-27-PNEPSW4100-30-PNEPSW4110-33-PNEPSW4120-36-PNEPSW4160-48-PNEPSW4200-60-PN
●●●●●●●●●●●
456789
1011121620
6 7.5 9 10.5 12 13.5 15 16.5 18 24 30
3.7 4.6 5.5 6.4 7.3 8.3 9.1 10.2 11 14.5 18.2
565656636374748686
110125
66688
101012121620
0.30.30.40.40.50.50.50.50.50.70.7
1215182124273033364860
33444444444
AABABABABBB
EPSW - -PN
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
0-0.05
EPSW
φ6~φ12 φ16,φ20
h5 h6
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.23General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.25
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.28EPSWEpoch Wave
Line Up
Roughing type φ4~φ20RegularHelix 30°
CarbideCoated
Helix 30°Carbide
CoatedUnequal
Pitch
UnequalPitch
UnequalPitch
Helix 30°Carbide
Coated
EPSWLEpoch Wave
Epoch Wave
Roughing type φ6~φ20Long
Roughing type φ4~φ20Under neck 3Dc
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes
Cornerchamfering
width Shape
EPSF-PN Epoch SUS Finish -Regular 3 ~12
EPSFM-PN Epoch SUS Finish -Medium 3 ~12
EPSFL-PN Epoch SUS Finish -Long 3 ~12
6~12 4~12
6~12 4~12
6~12 4~12
EPSW3040-20-PNEPSW3050-25-PNEPSW4060-30-PNEPSW4070-35-PNEPSW4080-40-PNEPSW4090-45-PNEPSW4100-50-PNEPSW4110-55-PNEPSW4120-60-PNEPSW4160-80-PNEPSW4200-100-PN
●●●●●●●●●●●
456789
1011121620
6 7.5 9 10.5 12 13.5 15 16.5 18 24 30
3.7 4.6 5.5 6.4 7.3 8.3 9.1 10.2 11 14.5 18.2
68686880809494
110110135155
66688
101012121620
20253035404550556080
100
33444444444
AABABABABBB
EPSW - -PN
●:Stocked Items.
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
0.30.30.40.40.50.50.50.50.50.70.7
0-0.05
2322
ap=1Dc, ae=0.5Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
760780810830860880910930960960950960940940960940940970960920910890870820840810820800800780770
ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.1Dc ap=1Dc, ae=0.05Dc
22,300 14,900 11,100 8,900 7,400 6,400 5,600 5,000 4,500 4,100 3,700 3,400 3,200 3,000 2,800 2,600 2,500 2,300 2,200 2,100 2,000 1,900 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,200 1,100
360370380390400410430440450450440440450450450440450440440430420400410390390390380370350370350
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
310310320330350350360370380380380380380370380370380380380370360360350340340340330310320310320
12,700 8,500 6,400 5,100 4,200 3,600 3,200 2,800 2,500 2,300 2,100 2,000 1,800 1,700 1,600 1,500 1,400 1,300 1,300 1,200 1,200 1,100 1,100 1,000
900 800 800 700 700 700 600
150160160170170170180180190190190200190190190190190190200180190170180170160150160150150160140
9,500 6,400 4,800 3,800 3,200 2,700 2,400 2,100 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
900 900 800 800 700 700 600 600 600 500 500 500
767982838687919295939697989796939995
100929485868085778285747780
31,800 21,200 15,900 12,700 10,600 9,100 8,000 7,100 6,400 5,800 5,300 4,900 4,500 4,200 4,000 3,700 3,500 3,400 3,200 3,000 2,900 2,800 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600
ap
ae
※ Please reduce feed rate to 75% because EPSW with dia. 4, 4,5, 5 and 5.5 are 3 flutes type. ※2 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type.
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible. These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
φ6~φ12 φ16,φ20
h5 h6
Product NameOuter Dia. End
ShapeRe-grinding compatibility
range (mm)Item Code
Re-grinding compatibility range table Line uptool dia.
(mm)
EPSM-CR-PN Epoch SUS Multi -Regular, Corner Radius 1 ~20
EPSML-CR-PN Epoch SUS Multi -Long, Corner Radius 6 ~20
EPSM-5Dc-CR-PN Epoch SUS Multi -Under neck 5Dc, Corner Radius 1 ~20 6~20 4~20
6~20 6~20
6~20 4~20
EPSMS-PN Epoch SUS Multi -Short 1 ~20
EPSM-PN Epoch SUS Multi -Regular 1 ~20
EPSML-PN Epoch SUS Multi -Long 6 ~20 6~20 6~20
6~20 4~20
6~20 4~20
EPSMLS-PN Epoch SUS Multi -Long shank 3 ~17 6~17 4~17
EPSMM-PN Epoch SUS Multi -Medium 3 ~20 6~20 4~20
EPSW-PN Epoch SUS Wave -Regular 4 ~20
EPSWL-PN Epoch SUS Wave -Long 6 ~20
EPSW-3Dc-PN Epoch SUS Wave -Under neck 3Dc 4 ~20
EPSW-5Dc-PN Epoch SUS Wave -Under neck 5Dc 4 ~20
EPSM-3Dc-PN Epoch SUS Multi -Under neck 3Dc 1 ~20
EPSM-5Dc-PN Epoch SUS Multi -Under neck 5Dc 1 ~20
6~20 4~20
6~20 4~20
6~20 6~20
6~20 4~20
6~20 4~20
6~20 4~20
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.27
L ine up, Re-gr inding
EPSWEpoch Wave
Helix 30°Carbide
CoatedUnequal
PitchRoughing type φ4~φ20Under neck 5Dc
Recommended Cutting Conditions
General Side milling conditions
EPSM EPSM-3DcEPSM-CREPSMS※2 EPSW EPSW-3DcShort Regular Regular, Corner radius Under neck 3Dc Regular, Roughing Under neck 3Dc, Roughing
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Item Code Stock
Size (mm)Tool dia.
Dc
Flute length
R
Under neck lengthR2
Neck dia.
D1
Overalllength
L
Shank dia.
Ds
No. of flutes
Cornerchamfering
width Shape
EPSF-PN Epoch SUS Finish -Regular 3 ~12
EPSFM-PN Epoch SUS Finish -Medium 3 ~12
EPSFL-PN Epoch SUS Finish -Long 3 ~12
6~12 4~12
6~12 4~12
6~12 4~12
EPSW3040-20-PNEPSW3050-25-PNEPSW4060-30-PNEPSW4070-35-PNEPSW4080-40-PNEPSW4090-45-PNEPSW4100-50-PNEPSW4110-55-PNEPSW4120-60-PNEPSW4160-80-PNEPSW4200-100-PN
●●●●●●●●●●●
456789
1011121620
6 7.5 9 10.5 12 13.5 15 16.5 18 24 30
3.7 4.6 5.5 6.4 7.3 8.3 9.1 10.2 11 14.5 18.2
68686880809494
110110135155
66688
101012121620
20253035404550556080
100
33444444444
AABABABABBB
EPSW - -PN
●:Stocked Items.
RR2
L
φDc
φDc
φD
1
φDs
φDs
RR2
L
20°
B type
A type φD
1
0.30.30.40.40.50.50.50.50.50.70.7
0-0.05
2322
ap=1Dc, ae=0.5Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
760780810830860880910930960960950960940940960940940970960920910890870820840810820800800780770
ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.1Dc ap=1Dc, ae=0.05Dc
22,300 14,900 11,100 8,900 7,400 6,400 5,600 5,000 4,500 4,100 3,700 3,400 3,200 3,000 2,800 2,600 2,500 2,300 2,200 2,100 2,000 1,900 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,200 1,100
360370380390400410430440450450440440450450450440450440440430420400410390390390380370350370350
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
310310320330350350360370380380380380380370380370380380380370360360350340340340330310320310320
12,700 8,500 6,400 5,100 4,200 3,600 3,200 2,800 2,500 2,300 2,100 2,000 1,800 1,700 1,600 1,500 1,400 1,300 1,300 1,200 1,200 1,100 1,100 1,000
900 800 800 700 700 700 600
150160160170170170180180190190190200190190190190190190200180190170180170160150160150150160140
9,500 6,400 4,800 3,800 3,200 2,700 2,400 2,100 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
900 900 800 800 700 700 600 600 600 500 500 500
767982838687919295939697989796939995
100929485868085778285747780
31,800 21,200 15,900 12,700 10,600 9,100 8,000 7,100 6,400 5,800 5,300 4,900 4,500 4,200 4,000 3,700 3,500 3,400 3,200 3,000 2,900 2,800 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600
ap
ae
※ Please reduce feed rate to 75% because EPSW with dia. 4, 4,5, 5 and 5.5 are 3 flutes type. ※2 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type.
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible. These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
φ6~φ12 φ16,φ20
h5 h6
Product NameOuter Dia. End
ShapeRe-grinding compatibility
range (mm)Item Code
Re-grinding compatibility range table Line uptool dia.
(mm)
EPSM-CR-PN Epoch SUS Multi -Regular, Corner Radius 1 ~20
EPSML-CR-PN Epoch SUS Multi -Long, Corner Radius 6 ~20
EPSM-5Dc-CR-PN Epoch SUS Multi -Under neck 5Dc, Corner Radius 1 ~20 6~20 4~20
6~20 6~20
6~20 4~20
EPSMS-PN Epoch SUS Multi -Short 1 ~20
EPSM-PN Epoch SUS Multi -Regular 1 ~20
EPSML-PN Epoch SUS Multi -Long 6 ~20 6~20 6~20
6~20 4~20
6~20 4~20
EPSMLS-PN Epoch SUS Multi -Long shank 3 ~17 6~17 4~17
EPSMM-PN Epoch SUS Multi -Medium 3 ~20 6~20 4~20
EPSW-PN Epoch SUS Wave -Regular 4 ~20
EPSWL-PN Epoch SUS Wave -Long 6 ~20
EPSW-3Dc-PN Epoch SUS Wave -Under neck 3Dc 4 ~20
EPSW-5Dc-PN Epoch SUS Wave -Under neck 5Dc 4 ~20
EPSM-3Dc-PN Epoch SUS Multi -Under neck 3Dc 1 ~20
EPSM-5Dc-PN Epoch SUS Multi -Under neck 5Dc 1 ~20
6~20 4~20
6~20 4~20
6~20 6~20
6~20 4~20
6~20 4~20
6~20 4~20
General Side milling conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.26General Slotting conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P.27
L ine up, Re-gr inding
EPSWEpoch Wave
Helix 30°Carbide
CoatedUnequal
PitchRoughing type φ4~φ20Under neck 5Dc
Recommended Cutting Conditions
General Side milling conditions
EPSM EPSM-3DcEPSM-CREPSMS※2 EPSW EPSW-3DcShort Regular Regular, Corner radius Under neck 3Dc Regular, Roughing Under neck 3Dc, Roughing
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Carbon steels, Alloy steelsCast iron
(~30HRC)
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
2524
ap=1Dc, ae=0.5Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
990 1,020 1,060 1,080 1,120 1,140 1,170 1,200 1,250 1,240 1,240 1,250 1,240 1,240 1,250 1,250 1,240 1,250 1,230 1,190 1,190 1,140 1,100 1,100 1,100 1,080 1,060 1,020 1,020 1,020 1,010
ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.1Dc ap=1Dc, ae=0.05Dc
31,800 21,200 15,900 12,700 10,600 9,100 8,000 7,100 6,400 5,800 5,300 4,900 4,500 4,200 4,000 3,700 3,500 3,400 3,200 3,000 2,900 2,800 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600
510520540550570590610620640640640640630630640630630650640610610590580550560540540540530520510
28,600 19,100 14,300 11,500 9,500 8,200 7,200 6,400 5,700 5,200 4,800 4,400 4,100 3,800 3,600 3,400 3,200 3,000 2,900 2,700 2,600 2,500 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400
460470490500510530550560570570580570570570580580580570580550540530520500490490490480470460450
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
230230240250260270270270280290290280280280290280280280290270270270260260260250240230240230240
15,900 10,600 8,000 6,400 5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,100 1,100 1,000
900 900 800 800
127130136139143145152153160160162156161158160162162162160153146148140137134142136127133123128
41,400 27,600 20,700 16,600 13,800 11,800 10,300 9,200 8,300 7,500 6,900 6,400 5,900 5,500 5,200 4,900 4,600 4,400 4,100 3,900 3,800 3,600 3,400 3,200 3,000 2,800 2,600 2,400 2,300 2,200 2,100
ap
ae
※2 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible. These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
※ Please reduce feed rate to 75% because EPSW with dia. 4, 4,5, 5 and 5.5 are 3 flutes type. ※2 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type.
ap=1Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
360390430470500540580610640680720710720710720720720710730690680660650630610610610600590580560
ap=1Dc ap=1Dc ap=0.5Dc ap=0.5Dc
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
190210230250270290310320340370380380380370380370380380380370360360350340340340330310320310320
17,500 11,700 8,800 7,000 5,800 5,000 4,400 3,900 3,500 3,200 2,900 2,700 2,500 2,300 2,200 2,100 1,900 1,800 1,800 1,700 1,600 1,500 1,500 1,300 1,300 1,200 1,100 1,000 1,000
900 900
130140160170180200210220240250260260260260260270260260270260250240240220240230220210220210220
11,100 7,400 5,600 4,500 3,700 3,200 2,800 2,500 2,200 2,000 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,200 1,100 1,100 1,000 1,000
900 900 800 700 700 700 600 600 600
60607070808090
10010010011011011011011011011011011011010011010010010090
1001009090
100
6,400 4,200 3,200 2,500 2,100 1,800 1,600 1,400 1,300 1,200 1,100 1,000
900 800 800 700 700 700 600 600 600 600 500 500 500 400 400 400 400 300 300
19212324262831323538403938363836384036373838323437313334352829
28,600 19,100 14,300 11,500 9,500 8,200 7,200 6,400 5,700 5,200 4,800 4,400 4,100 3,800 3,600 3,400 3,200 3,000 2,900 2,700 2,600 2,500 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400
ap
ae
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible.These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.Please setup feed 1/5 that of slotting parameter and step 0.01Dc for drilling application.Please setup feed 70% of slotting parameter and ramping angle 3° for ramping application.
High speed Side milling conditions
EPSM EPSM-3DcEPSM-CREPSMS※2
Short Regular Regular, Corner radius Under neck 3Dc
General Slotting conditions
EPSM EPSM-3DcEPSM-CREPSMS※2 EPSW EPSW-3DcShort Regular Regular, Corner radius Under neck 3Dc Regular, Roughing Under neck 3Dc, Roughing
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Recommended Cutting Conditions
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Carbon steels, Alloy steelsCast iron
(~30HRC)
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
2524
ap=1Dc, ae=0.5Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
990 1,020 1,060 1,080 1,120 1,140 1,170 1,200 1,250 1,240 1,240 1,250 1,240 1,240 1,250 1,250 1,240 1,250 1,230 1,190 1,190 1,140 1,100 1,100 1,100 1,080 1,060 1,020 1,020 1,020 1,010
ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.5Dc ap=1Dc, ae=0.1Dc ap=1Dc, ae=0.05Dc
31,800 21,200 15,900 12,700 10,600 9,100 8,000 7,100 6,400 5,800 5,300 4,900 4,500 4,200 4,000 3,700 3,500 3,400 3,200 3,000 2,900 2,800 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600
510520540550570590610620640640640640630630640630630650640610610590580550560540540540530520510
28,600 19,100 14,300 11,500 9,500 8,200 7,200 6,400 5,700 5,200 4,800 4,400 4,100 3,800 3,600 3,400 3,200 3,000 2,900 2,700 2,600 2,500 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400
460470490500510530550560570570580570570570580580580570580550540530520500490490490480470460450
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
230230240250260270270270280290290280280280290280280280290270270270260260260250240230240230240
15,900 10,600 8,000 6,400 5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,100 1,100 1,000
900 900 800 800
127130136139143145152153160160162156161158160162162162160153146148140137134142136127133123128
41,400 27,600 20,700 16,600 13,800 11,800 10,300 9,200 8,300 7,500 6,900 6,400 5,900 5,500 5,200 4,900 4,600 4,400 4,100 3,900 3,800 3,600 3,400 3,200 3,000 2,800 2,600 2,400 2,300 2,200 2,100
ap
ae
※2 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible. These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
※ Please reduce feed rate to 75% because EPSW with dia. 4, 4,5, 5 and 5.5 are 3 flutes type. ※2 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type.
ap=1Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
360390430470500540580610640680720710720710720720720710730690680660650630610610610600590580560
ap=1Dc ap=1Dc ap=0.5Dc ap=0.5Dc
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
190210230250270290310320340370380380380370380370380380380370360360350340340340330310320310320
17,500 11,700 8,800 7,000 5,800 5,000 4,400 3,900 3,500 3,200 2,900 2,700 2,500 2,300 2,200 2,100 1,900 1,800 1,800 1,700 1,600 1,500 1,500 1,300 1,300 1,200 1,100 1,000 1,000
900 900
130140160170180200210220240250260260260260260270260260270260250240240220240230220210220210220
11,100 7,400 5,600 4,500 3,700 3,200 2,800 2,500 2,200 2,000 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,200 1,100 1,100 1,000 1,000
900 900 800 700 700 700 600 600 600
60607070808090
10010010011011011011011011011011011011010011010010010090
1001009090
100
6,400 4,200 3,200 2,500 2,100 1,800 1,600 1,400 1,300 1,200 1,100 1,000
900 800 800 700 700 700 600 600 600 600 500 500 500 400 400 400 400 300 300
19212324262831323538403938363836384036373838323437313334352829
28,600 19,100 14,300 11,500 9,500 8,200 7,200 6,400 5,700 5,200 4,800 4,400 4,100 3,800 3,600 3,400 3,200 3,000 2,900 2,700 2,600 2,500 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400
ap
ae
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
※
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible.These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.Please setup feed 1/5 that of slotting parameter and step 0.01Dc for drilling application.Please setup feed 70% of slotting parameter and ramping angle 3° for ramping application.
High speed Side milling conditions
EPSM EPSM-3DcEPSM-CREPSMS※2
Short Regular Regular, Corner radius Under neck 3Dc
General Slotting conditions
EPSM EPSM-3DcEPSM-CREPSMS※2 EPSW EPSW-3DcShort Regular Regular, Corner radius Under neck 3Dc Regular, Roughing Under neck 3Dc, Roughing
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Recommended Cutting ConditionsD
imensions,
SU
S M
ultiD
imensions,
SU
S Finish
Dim
ensions,S
US
Wave
FeaturesC
utting conditionR
e-grindingTechnical D
ata
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
2726
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
ap
ae
ap=0.5Dc, ae=0.25Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
ap=0.5Dc, ae=0.25Dc ap=0.5Dc, ae=0.25Dc ap=0.5Dc, ae=0.1Dc ap=0.5Dc, ae=0.05Dc
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
310320320330350360360370380390380380380380380370380380380370360360350350340340330310330310320
15,900 10,600 8,000 6,400 5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,100 1,100 1,000
900 900 800 800
250260270280290290300310320320320310320320320320320320320310290300280280270280270260270250260
12,700 8,500 6,400 5,100 4,200 3,600 3,200 2,800 2,500 2,300 2,100 2,000 1,800 1,700 1,600 1,500 1,400 1,300 1,300 1,200 1,200 1,100 1,100 1,000
900 800 800 700 700 700 600
150160160170170180180190190190190200190190190190190190200190190180180170170150160150160160140
9,500 6,400 4,800 3,800 3,200 2,700 2,400 2,100 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
900 900 800 800 700 700 600 600 600 500 500 500
768082848688919395949698989896949995
100939486868186778286757780
28,600 19,100 14,300 11,500 9,500 8,200 7,200 6,400 5,700 5,200 4,800 4,400 4,100 3,800 3,600 3,400 3,200 3,000 2,900 2,700 2,600 2,500 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400
690710730760770800820850860860860860860860860870860860870830820800780760740740730730720690670
※
※
※
※
※
※
※
※
※
※
EPSM-5Dc EPSW-5DcEPSM-5Dc-CRUnder neck 5Dc
EPSMLS※4
Long shank Under neck 5Dc, Corner radius Under neck 5Dc, Roughing
※ Please reduce feed rate to 75% because EPSW with dia. 4, and 5 are 3 flutes type. ※4 The above table shows cutting conditions for 5Dc type tools with a 5Dc overhang. Adjust conditions according to the tool overhang amount.
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
320350380410450480510550570600630630630640640640630640630620600590570580550550540540520500520
15,900 10,600 8,000 6,400 5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,100 1,100 1,000
900 900 800 800
160170190210220240260270290300320310320320320320320320320310290300280280270280270260270250260
14,300 9,500 7,200 5,700 4,800 4,100 3,600 3,200 2,900 2,600 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,200 1,100 1,000 1,000
900 800 800 800 700
110120130140150160170180200200220210210210220220220210210220200190190190180190180170180180170
9,500 6,400 4,800 3,800 3,200 2,700 2,400 2,100 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
900 900 800 800 700 700 600 600 600 500 500 500
50506060707080809090
10010010010010090
100100100909090908090808090708080
4,800 3,200 2,400 1,900 1,600 1,400 1,200 1,100 1,000
900 800 700 700 600 600 600 500 500 500 500 400 400 400 400 300 300 300 300 300 300 200
14161719202223252728292729272931272930312526262822232426272819
25,500 17,000 12,700 10,200 8,500 7,300 6,400 5,700 5,100 4,600 4,200 3,900 3,600 3,400 3,200 3,000 2,800 2,700 2,500 2,400 2,300 2,200 2,100 2,000 1,800 1,700 1,600 1,500 1,400 1,300 1,300
※
※
※
※
※
※
※
※
※
※
ap
ae
ap=0.5Dc ap=0.5Dc ap=0.5Dc ap=0.25Dc ap=0.25Dc
※Please reduce feed rate to 75% because EPSW with dia. 4, and 5 are 3 flutes type.
EPSM-5Dc EPSW-5DcEPSM-5Dc-CRUnder neck 5Dc Under neck 5Dc, Corner radius Under neck 5Dc, Roughing
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.Please setup feed 1/5 that of slotting parameter and step 0.01Dc for drilling application.Please setup feed 70% of slotting parameter and ramping angle 3° for ramping application.
Recommended Cutting Conditions
General Side milling conditions General Slotting conditions
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
2726
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
ap
ae
ap=0.5Dc, ae=0.25Dc
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
ap=0.5Dc, ae=0.25Dc ap=0.5Dc, ae=0.25Dc ap=0.5Dc, ae=0.1Dc ap=0.5Dc, ae=0.05Dc
19,100 12,700 9,500 7,600 6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,900 2,700 2,500 2,400 2,200 2,100 2,000 1,900 1,800 1,700 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
310320320330350360360370380390380380380380380370380380380370360360350350340340330310330310320
15,900 10,600 8,000 6,400 5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,100 1,100 1,000
900 900 800 800
250260270280290290300310320320320310320320320320320320320310290300280280270280270260270250260
12,700 8,500 6,400 5,100 4,200 3,600 3,200 2,800 2,500 2,300 2,100 2,000 1,800 1,700 1,600 1,500 1,400 1,300 1,300 1,200 1,200 1,100 1,100 1,000
900 800 800 700 700 700 600
150160160170170180180190190190190200190190190190190190200190190180180170170150160150160160140
9,500 6,400 4,800 3,800 3,200 2,700 2,400 2,100 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
900 900 800 800 700 700 600 600 600 500 500 500
768082848688919395949698989896949995
100939486868186778286757780
28,600 19,100 14,300 11,500 9,500 8,200 7,200 6,400 5,700 5,200 4,800 4,400 4,100 3,800 3,600 3,400 3,200 3,000 2,900 2,700 2,600 2,500 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400
690710730760770800820850860860860860860860860870860860870830820800780760740740730730720690670
※
※
※
※
※
※
※
※
※
※
EPSM-5Dc EPSW-5DcEPSM-5Dc-CRUnder neck 5Dc
EPSMLS※4
Long shank Under neck 5Dc, Corner radius Under neck 5Dc, Roughing
※ Please reduce feed rate to 75% because EPSW with dia. 4, and 5 are 3 flutes type. ※4 The above table shows cutting conditions for 5Dc type tools with a 5Dc overhang. Adjust conditions according to the tool overhang amount.
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
320350380410450480510550570600630630630640640640630640630620600590570580550550540540520500520
15,900 10,600 8,000 6,400 5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,100 1,100 1,000
900 900 800 800
160170190210220240260270290300320310320320320320320320320310290300280280270280270260270250260
14,300 9,500 7,200 5,700 4,800 4,100 3,600 3,200 2,900 2,600 2,400 2,200 2,000 1,900 1,800 1,700 1,600 1,500 1,400 1,400 1,300 1,200 1,200 1,100 1,000 1,000
900 800 800 800 700
110120130140150160170180200200220210210210220220220210210220200190190190180190180170180180170
9,500 6,400 4,800 3,800 3,200 2,700 2,400 2,100 1,900 1,700 1,600 1,500 1,400 1,300 1,200 1,100 1,100 1,000 1,000
900 900 800 800 700 700 600 600 600 500 500 500
50506060707080809090
10010010010010090
100100100909090908090808090708080
4,800 3,200 2,400 1,900 1,600 1,400 1,200 1,100 1,000
900 800 700 700 600 600 600 500 500 500 500 400 400 400 400 300 300 300 300 300 300 200
14161719202223252728292729272931272930312526262822232426272819
25,500 17,000 12,700 10,200 8,500 7,300 6,400 5,700 5,100 4,600 4,200 3,900 3,600 3,400 3,200 3,000 2,800 2,700 2,500 2,400 2,300 2,200 2,100 2,000 1,800 1,700 1,600 1,500 1,400 1,300 1,300
※
※
※
※
※
※
※
※
※
※
ap
ae
ap=0.5Dc ap=0.5Dc ap=0.5Dc ap=0.25Dc ap=0.25Dc
※Please reduce feed rate to 75% because EPSW with dia. 4, and 5 are 3 flutes type.
EPSM-5Dc EPSW-5DcEPSM-5Dc-CRUnder neck 5Dc Under neck 5Dc, Corner radius Under neck 5Dc, Roughing
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.Please setup feed 1/5 that of slotting parameter and step 0.01Dc for drilling application.Please setup feed 70% of slotting parameter and ramping angle 3° for ramping application.
Recommended Cutting Conditions
General Side milling conditions General Slotting conditions
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
ap
ae
ap
ae
68
10121620
ap=3Dc, ae=0.05Dc ap=3Dc, ae=0.05Dc ap=3Dc, ae=0.02Dc ap=3Dc, ae=0.01Dcap=3Dc, ae=0.05Dc
1,900 1,400 1,100
900 700 600
230220220190190190
1,600 1,200 1,000
800 600 500
190190200170160160
1,100 800 600 500 400 300
10010090808070
800 600 500 400 300 200
484850434132
2,700 2,000 1,600 1,300 1,000
800
490480480420410380
3456789
1011121620
5,3004,0003,2002,6002,2002,0001,7001,6001,4001,3001,000
800
290300320310310320310320290280270260
4,5003,4002,7002,3002,0001,7001,5001,4001,2001,100
850650
240260270270280270270280250240230210
3,0002,2001,8001,5001,3001,1001,000
900800750550450
120120130130130130130130120120110110
2,1001,6001,3001,100
900800700600600500400300
576165666364636063545448
7,4005,6004,5003,7003,2002,8002,5002,2002,0001,8001,4001,100
600640670660670670670660630580570530
ap=2.5Dc, ae=0.05Dc ap=2.5Dc, ae=0.05Dc ap=2.5Dc, ae=0.03Dc ap=2.5Dc, ae=0.02Dcap=2.5Dc, ae=0.05Dc
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
2928
3 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12
850 850 900 900 950 940 950 960 950 950 950 910 870
6,900 5,900 5,200 4,600 4,100 3,800 3,400 3,000 2,600 2,300 2,100 1,900 1,700
470 460 490 490 510 520 510 530 520 520 530 500 460
6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,700 2,400 2,100 1,900 1,700 1,600
430 430 460 450 480 480 480 470 480 470 480 440 430
5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,300 2,000 1,800 1,600 1,400 1,300
140 140 150 150 160 160 160 160 160 160 160 150 140
4,200 3,600 3,200 2,800 2,500 2,300 2,100 1,800 1,600 1,400 1,300 1,200 1,100
85 85 91 90 94 95 95 95 96 95 98 94 89
9,000 7,700 6,800 6,000 5,400 4,900 4,500 3,900 3,400 3,000 2,700 2,500 2,300
ap
ae
ap=1.0Dc, ae=0.2Dc ap=1.0Dc, ae=0.1Dc ap=1.0Dc, ae=0.1Dc ap=1.0Dc, ae=0.05Dc ap=1.0Dc, ae=0.05Dc
EPSFRegular
【Note】
EPSMMMedium
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
General Side milling conditions
EPSML EPSWLEPSML-CRLong Long, Corner radius Long, Roughing
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type.
General Side milling conditions General Side milling conditions
Recommended Cutting Conditions
ap
ae
ap
ae
68
10121620
ap=3Dc, ae=0.05Dc ap=3Dc, ae=0.05Dc ap=3Dc, ae=0.02Dc ap=3Dc, ae=0.01Dcap=3Dc, ae=0.05Dc
1,900 1,400 1,100
900 700 600
230220220190190190
1,600 1,200 1,000
800 600 500
190190200170160160
1,100 800 600 500 400 300
10010090808070
800 600 500 400 300 200
484850434132
2,700 2,000 1,600 1,300 1,000
800
490480480420410380
3456789
1011121620
5,3004,0003,2002,6002,2002,0001,7001,6001,4001,3001,000
800
290300320310310320310320290280270260
4,5003,4002,7002,3002,0001,7001,5001,4001,2001,100
850650
240260270270280270270280250240230210
3,0002,2001,8001,5001,3001,1001,000
900800750550450
120120130130130130130130120120110110
2,1001,6001,3001,100
900800700600600500400300
576165666364636063545448
7,4005,6004,5003,7003,2002,8002,5002,2002,0001,8001,4001,100
600640670660670670670660630580570530
ap=2.5Dc, ae=0.05Dc ap=2.5Dc, ae=0.05Dc ap=2.5Dc, ae=0.03Dc ap=2.5Dc, ae=0.02Dcap=2.5Dc, ae=0.05Dc
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
2928
3 3.5 4 4.5 5 5.5 6 7 8 9 10 11 12
850 850 900 900 950 940 950 960 950 950 950 910 870
6,900 5,900 5,200 4,600 4,100 3,800 3,400 3,000 2,600 2,300 2,100 1,900 1,700
470 460 490 490 510 520 510 530 520 520 530 500 460
6,400 5,500 4,800 4,200 3,800 3,500 3,200 2,700 2,400 2,100 1,900 1,700 1,600
430 430 460 450 480 480 480 470 480 470 480 440 430
5,300 4,500 4,000 3,500 3,200 2,900 2,700 2,300 2,000 1,800 1,600 1,400 1,300
140 140 150 150 160 160 160 160 160 160 160 150 140
4,200 3,600 3,200 2,800 2,500 2,300 2,100 1,800 1,600 1,400 1,300 1,200 1,100
85 85 91 90 94 95 95 95 96 95 98 94 89
9,000 7,700 6,800 6,000 5,400 4,900 4,500 3,900 3,400 3,000 2,700 2,500 2,300
ap
ae
ap=1.0Dc, ae=0.2Dc ap=1.0Dc, ae=0.1Dc ap=1.0Dc, ae=0.1Dc ap=1.0Dc, ae=0.05Dc ap=1.0Dc, ae=0.05Dc
EPSFRegular
【Note】
EPSMMMedium
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
General Side milling conditions
EPSML EPSWLEPSML-CRLong Long, Corner radius Long, Roughing
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type.
General Side milling conditions General Side milling conditions
Recommended Cutting Conditions
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
3130
EPSFRegular
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
980 1,010 1,050 1,070 1,110 1,130 1,170 1,190 1,230 1,230 1,230 1,230 1,230 1,240 1,230 1,240 1,240 1,230 1,240 1,180 1,160 1,140 1,110 1,080 1,090 1,040 1,030 1,030 1,000 1,000
990
35,000 23,300 17,500 14,000 11,700 10,000 8,800 7,800 7,000 6,400 5,800 5,400 5,000 4,700 4,400 4,100 3,900 3,700 3,500 3,300 3,200 3,000 2,900 2,700 2,500 2,300 2,200 2,100 1,900 1,800 1,800
500520540550570580600610630630630630630630630630630630630600600570560560550530540530500500520
31,500 21,000 15,800 12,600 10,500 9,000 7,900 7,000 6,300 5,700 5,300 4,800 4,500 4,200 3,900 3,700 3,500 3,300 3,200 3,000 2,900 2,700 2,600 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600
450460480490510520540550570560570560570570560570570560580550550510510490500490490480480470460
21,000 14,000 10,500 8,400 7,000 6,000 5,300 4,700 4,200 3,800 3,500 3,200 3,000 2,800 2,600 2,500 2,300 2,200 2,100 2,000 1,900 1,800 1,800 1,600 1,500 1,400 1,300 1,200 1,200 1,100 1,100
230230240250260260270280280280280280280280280290280280280270270260260250250240240230240230240
17,500 11,700 8,800 7,000 5,800 5,000 4,400 3,900 3,500 3,200 2,900 2,700 2,500 2,300 2,200 2,100 1,900 1,800 1,800 1,700 1,600 1,500 1,500 1,300 1,300 1,200 1,100 1,000 1,000
900 900
130130130140140140150150160160160160160160160160150150160160150140150130140140130130130120130
45,500 30,300 22,800 18,200 15,200 13,000 11,400 10,100 9,100 8,300 7,600 7,000 6,500 6,100 5,700 5,400 5,100 4,800 4,600 4,300 4,100 4,000 3,800 3,500 3,300 3,000 2,800 2,700 2,500 2,400 2,300
Side finishing conditions
ap
ae
ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc
※3 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type, please reduce both rotation and feed rate to 70% when using 5Dc type
EPSM EPSM-3DcEPSM-CREPSMS※3
Short Regular Regular, Corner radius Under neck 3DcEPSM-5Dc※3
Under neck 5DcEPSM-5Dc-CR※3
Under neck 5Dc, Corner radius
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible. These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
3456789
101112
480 510 530 530 530 530 540 530 490 470
4,060 3,080 2,450 2,030 1,750 1,540 1,330 1,260 1,120 1,050
250 260 280 270 280 280 270 280 260 260
4,830 3,640 2,870 2,380 2,100 1,820 1,610 1,470 1,330 1,190
290 310 320 320 330 330 330 330 310 290
4,830 3,640 2,870 2,380 2,100 1,820 1,610 1,470 1,330 1,190
180 190 190 190 200 200 200 200 190 170
2,940 2,240 1,750 1,470 1,260 1,120
980 910 840 770
71 77 79 79 79 81 79 82 79 75
7,070 5,320 4,200 3,500 3,010 2,660 2,380 2,100 1,890 1,750
Side finishing conditions
ap
ae
ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc
EPSFL
EPSFMMedium
Long
3456789
101112
340 360 380 380 380 380 380 380 350 340
2,900 2,200 1,750 1,450 1,250 1,100
950 900 800 750
180 190 200 200 200 200 190 200 190 180
3,450 2,600 2,050 1,700 1,500 1,300 1,150 1,050
950 850
210 220 230 230 240 230 230 240 220 210
3,450 2,600 2,050 1,700 1,500 1,300 1,150 1,050
950 850
130 130 140 140 140 140 140 140 130 120
2,100 1,600 1,250 1,050
900 800 700 650 600 550
51 55 56 57 57 58 57 59 56 53
5,050 3,800 3,000 2,500 2,150 1,900 1,700 1,500 1,350 1,250
Side finishing conditions
ap
ae
ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc
【Note】
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type.
Recommended Cutting Conditions
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
3130
EPSFRegular
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12 13 14 15 16 17 18 19 20
980 1,010 1,050 1,070 1,110 1,130 1,170 1,190 1,230 1,230 1,230 1,230 1,230 1,240 1,230 1,240 1,240 1,230 1,240 1,180 1,160 1,140 1,110 1,080 1,090 1,040 1,030 1,030 1,000 1,000
990
35,000 23,300 17,500 14,000 11,700 10,000 8,800 7,800 7,000 6,400 5,800 5,400 5,000 4,700 4,400 4,100 3,900 3,700 3,500 3,300 3,200 3,000 2,900 2,700 2,500 2,300 2,200 2,100 1,900 1,800 1,800
500520540550570580600610630630630630630630630630630630630600600570560560550530540530500500520
31,500 21,000 15,800 12,600 10,500 9,000 7,900 7,000 6,300 5,700 5,300 4,800 4,500 4,200 3,900 3,700 3,500 3,300 3,200 3,000 2,900 2,700 2,600 2,400 2,300 2,100 2,000 1,900 1,800 1,700 1,600
450460480490510520540550570560570560570570560570570560580550550510510490500490490480480470460
21,000 14,000 10,500 8,400 7,000 6,000 5,300 4,700 4,200 3,800 3,500 3,200 3,000 2,800 2,600 2,500 2,300 2,200 2,100 2,000 1,900 1,800 1,800 1,600 1,500 1,400 1,300 1,200 1,200 1,100 1,100
230230240250260260270280280280280280280280280290280280280270270260260250250240240230240230240
17,500 11,700 8,800 7,000 5,800 5,000 4,400 3,900 3,500 3,200 2,900 2,700 2,500 2,300 2,200 2,100 1,900 1,800 1,800 1,700 1,600 1,500 1,500 1,300 1,300 1,200 1,100 1,000 1,000
900 900
130130130140140140150150160160160160160160160160150150160160150140150130140140130130130120130
45,500 30,300 22,800 18,200 15,200 13,000 11,400 10,100 9,100 8,300 7,600 7,000 6,500 6,100 5,700 5,400 5,100 4,800 4,600 4,300 4,100 4,000 3,800 3,500 3,300 3,000 2,800 2,700 2,500 2,400 2,300
Side finishing conditions
ap
ae
ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc ap=1Dc, ae=0.001Dc~0.02Dc
※3 The table above indicates cutting parameter for regular type and 3Dc type, please reduce both rotation and feed rate to 1.1 times when using short type, please reduce both rotation and feed rate to 70% when using 5Dc type
EPSM EPSM-3DcEPSM-CREPSMS※3
Short Regular Regular, Corner radius Under neck 3DcEPSM-5Dc※3
Under neck 5DcEPSM-5Dc-CR※3
Under neck 5Dc, Corner radius
【Note】PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.Use the high-rigidity and high accuracy machine as possible. These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. Please adjust it if chatter or abnormal vibration occurs.
3456789
101112
480 510 530 530 530 530 540 530 490 470
4,060 3,080 2,450 2,030 1,750 1,540 1,330 1,260 1,120 1,050
250 260 280 270 280 280 270 280 260 260
4,830 3,640 2,870 2,380 2,100 1,820 1,610 1,470 1,330 1,190
290 310 320 320 330 330 330 330 310 290
4,830 3,640 2,870 2,380 2,100 1,820 1,610 1,470 1,330 1,190
180 190 190 190 200 200 200 200 190 170
2,940 2,240 1,750 1,470 1,260 1,120
980 910 840 770
71 77 79 79 79 81 79 82 79 75
7,070 5,320 4,200 3,500 3,010 2,660 2,380 2,100 1,890 1,750
Side finishing conditions
ap
ae
ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc ap=2.5Dc, ae=0.001Dc~0.01Dc
EPSFL
EPSFMMedium
Long
3456789
101112
340 360 380 380 380 380 380 380 350 340
2,900 2,200 1,750 1,450 1,250 1,100
950 900 800 750
180 190 200 200 200 200 190 200 190 180
3,450 2,600 2,050 1,700 1,500 1,300 1,150 1,050
950 850
210 220 230 230 240 230 230 240 220 210
3,450 2,600 2,050 1,700 1,500 1,300 1,150 1,050
950 850
130 130 140 140 140 140 140 140 130 120
2,100 1,600 1,250 1,050
900 800 700 650 600 550
51 55 56 57 57 58 57 59 56 53
5,050 3,800 3,000 2,500 2,150 1,900 1,700 1,500 1,350 1,250
Side finishing conditions
ap
ae
ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc ap=3Dc, ae=0.001Dc~0.01Dc
【Note】
Carbon steels, Alloy steelsCast iron
(~30HRC)
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Revolution nmin-1
Feed rate vfmm/min
Tool steels, Pre-hardened steels
(30~40HRC)
Stainless steels Titanium alloy Super heat-resistantalloy
Tool dia.Dc
(mm)
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
PN coating is less electro conductive. Therefore, electric transmitted measuring systems may not work.Use the appropriate coolant for the work material and machining shape.These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type.
Recommended Cutting Conditions
3332
Field data
Comparison of tool life by pocketing. EPSW
Tool life date by side milling. EPSM
Cutting example by side milling. EPSM
Work material:SUS304
Tool Result
EPSW4080-24-PNConventional A
Conventional B
Conventional C
Complete machining
Broken during interpolation
Broken during interpolation
Broken during interpolation
Work sizeφ16mm
12mm
Tool : Wave-form type φ8×4NT, n=5,000min-1(vc=125m/min), v f =500mm/min(fz=0.04mm/t), ap×ae=8×3mm, OH=24mm,Ramping angle =5°, Coolant : Wet
Work material:SUS304
Tool : Square type φ8×4NT, fz=0.04mm/t, ap×ae=8×3mm, OH=24mm, Coolant:Wet
ae
EPSM can achieve long life machining even in
high speed milling.
Cutting distance (m)
0 27 54 81 108 135 162 1890
0.05
0.1
0.15
vc=45m/min vc=60m/minvc=85m/min vc=125 m/min
Vb(㎜)
Work material:SUS304
Tool : Square type φ8×4NT, n=2,400min-1(vc=60m/min), v f=380mm/min(fz=0.04mm/t),ap×ae=8×3mm, OH=24mm, Coolant : wet
ap
ae
Cutting distance 405m (About 18 hours)Wear width Vb=0.088 mm
EPSM4080-24-PN
Cutting example for various cutting process. EPSM EPSW
Work material:SUS304
Tool : Epoch SUS series, Coolant:wet
【Cutting Conditions】
Side millingEpoch SUS Multiφ10×4NTEPSM4100-30-PN
Side rampingEpoch SUS Multiφ10×4NTEPSM4100-30-PN
SlottingEpoch SUS Waveφ10×4NTEPSW4100-30-PN
Thin wall pocketingEpoch SUS Waveφ10×4NTEPSW4100-30-PN
100mm
250mm
High efficiency machining for various situation
A
A
B
B
C
C
D
D
n=2,900min-1(vc=90m/min), vf=580mm/min(fz=0.05mm/t),ap×ae=10×5mm,Cutting time =4min.
n=1,900min-1(vc=60m/min), vf=300mm/min(fz=0.04mm/t)ap×ae=10×3mm, Ramping angle=5°, Cutting time =4min.
n=1,600min-1(vc=50m/min),vf=230mm/min(fz=0.036mm/t)ap×ae=10×10mm,Cutting time =3min.
n=1,900min-1(vc=60m/min), vf=380mm/min(fz=0.05mm/t)ap×ae=10×4mm, Thickness =2mm,Depth =25mm, Cutting time =20min.
Work after milling
Cutting edge after millingCutting edge after milling
Cutting edge after millingCutting edge after milling
Cutting example of thin wall work geometry. EPSW
Work material:SUS304
Tool:Wave-form type φ8×4NT, n=2,400min-1(vc=60m/min), vf=380mm/min(fz=0.04mm/t), ap×ae=8×4mm, Coolant : wet Cutting time =50min.
Depth= 20mmThickness= 2mm
100mm
250mm
Stable & high efficiency, even in poor-clamping & thin-wall work
geometry situations.
EPSW4080-24-PN
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
3332
Field data
Comparison of tool life by pocketing. EPSW
Tool life date by side milling. EPSM
Cutting example by side milling. EPSM
Work material:SUS304
Tool Result
EPSW4080-24-PNConventional A
Conventional B
Conventional C
Complete machining
Broken during interpolation
Broken during interpolation
Broken during interpolation
Work sizeφ16mm
12mm
Tool : Wave-form type φ8×4NT, n=5,000min-1(vc=125m/min), v f =500mm/min(fz=0.04mm/t), ap×ae=8×3mm, OH=24mm,Ramping angle =5°, Coolant : Wet
Work material:SUS304
Tool : Square type φ8×4NT, fz=0.04mm/t, ap×ae=8×3mm, OH=24mm, Coolant:Wet
ae
EPSM can achieve long life machining even in
high speed milling.
Cutting distance (m)
0 27 54 81 108 135 162 1890
0.05
0.1
0.15
vc=45m/min vc=60m/minvc=85m/min vc=125 m/min
Vb(㎜)
Work material:SUS304
Tool : Square type φ8×4NT, n=2,400min-1(vc=60m/min), v f=380mm/min(fz=0.04mm/t),ap×ae=8×3mm, OH=24mm, Coolant : wet
ap
ae
Cutting distance 405m (About 18 hours)Wear width Vb=0.088 mm
EPSM4080-24-PN
Cutting example for various cutting process. EPSM EPSW
Work material:SUS304
Tool : Epoch SUS series, Coolant:wet
【Cutting Conditions】
Side millingEpoch SUS Multiφ10×4NTEPSM4100-30-PN
Side rampingEpoch SUS Multiφ10×4NTEPSM4100-30-PN
SlottingEpoch SUS Waveφ10×4NTEPSW4100-30-PN
Thin wall pocketingEpoch SUS Waveφ10×4NTEPSW4100-30-PN
100mm
250mm
High efficiency machining for various situation
A
A
B
B
C
C
D
D
n=2,900min-1(vc=90m/min), vf=580mm/min(fz=0.05mm/t),ap×ae=10×5mm,Cutting time =4min.
n=1,900min-1(vc=60m/min), vf=300mm/min(fz=0.04mm/t)ap×ae=10×3mm, Ramping angle=5°, Cutting time =4min.
n=1,600min-1(vc=50m/min),vf=230mm/min(fz=0.036mm/t)ap×ae=10×10mm,Cutting time =3min.
n=1,900min-1(vc=60m/min), vf=380mm/min(fz=0.05mm/t)ap×ae=10×4mm, Thickness =2mm,Depth =25mm, Cutting time =20min.
Work after milling
Cutting edge after millingCutting edge after milling
Cutting edge after millingCutting edge after milling
Cutting example of thin wall work geometry. EPSW
Work material:SUS304
Tool:Wave-form type φ8×4NT, n=2,400min-1(vc=60m/min), vf=380mm/min(fz=0.04mm/t), ap×ae=8×4mm, Coolant : wet Cutting time =50min.
Depth= 20mmThickness= 2mm
100mm
250mm
Stable & high efficiency, even in poor-clamping & thin-wall work
geometry situations.
EPSW4080-24-PN
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
ap
ae
EPSF4060-PN Conventional
3534
Work material : SUS304
Tool : Square type (Regular) φ6×4NT n=3,500min-1(vc=66m/min), v f=480mm/min(fz=0.034mm/t), ap×ae=9×0.1mm Coolant:wet
Comparison of finishing performance EPSF
EPSF Conventional
Comparison of surface Comparison of surface roughness
0
0.2
0.4
0.6
0.8
1
1.2
1.4
Rz(
μm
)
Axial directionFeed direction
Excellent machined surfacewith few burrs on top
Comparison of tool life by side milling. EPSM
Cutting example by side milling. EPSM
Comparison of tool life by side milling. EPSW
Work material : Inconel-718 (46HRC)
Tool : Square type φ8×4NTn=1,200min-1(vc=30m/min), v f=140mm/min(fz=0.03mm/t)ap×ae=8×0.3mm, OH=24mmCoolant : wet
ap
ae
0
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0 5 10 15 20
Cutting distance (m)
Vb(㎜)
Conventional
After 7m
After 7m
EPSM4080-24-PN
EpochEpoch Multi
Work material : 15-5PH
Tool : Square type φ8×4NT, n=3,200min-1(vc=80m/min), v f=500mm/min(fz=0.04mm/t),ap×ae=3×1mm, OH=24mm, Coolant : wet
ap
ae
EPSM4080-24-PN
After 1.5 hours milling end mill still can be used for further application. Even in 15-5PH cutting.Vb=0.06mmVb=0.06mm
After 1.5hour useEPSM4080-24-PN
Work material : SUS304
Tool:Wave-form type φ8×4NT,n=5000min-1(vc=125m/min), v f=800mm/min(fz=0.04mm/t),ap×ae=8×3mm, OH=24mm, Coolant : Wet
0.15
0.1
0.05
00 10 20
ap
ae
Conventional A
Conventional B
Cutting distance (m)
EPSW4080-24-PN
Vb(㎜)
EpochEpoch Wave
Field data
Comparison of tool wear by slotting. EPSM
Comparison of tool life wear by slotting. EPSM-CR
Work material : SUS304
Tool:Square type φ8×4NT,n=4,200min-1(vc=108m/min), v f=230mm/min(fz=0.014mm/t),ap×ae=6.4×8mm, OH=24mm, Coolant : Wet, Cutting distance : 4m
ap
ae
EPSM4080-PNEPSM4080-PN Conventional A
Rake face
Relief face
Rake face
Relief face
Work material : SUS304
Tool:Radius type φ8×r1n=2,200min-1(vc=55m/min), v f=260mm/min(fz=0.3mm/t),ap×ae=8×8mm Coolant : Wet
Cutting distance (m)
Conventional A
Corner radius
Conventional B
Conventional C
0 2 4 6 8 10 12 14
Interrupted cutting is possible
Broken
Normal wear
Chipping occuredChipping occured
Chipping occuredChipping occured
EpochEpochMulti
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
ap
ae
EPSF4060-PN Conventional
3534
Work material : SUS304
Tool : Square type (Regular) φ6×4NT n=3,500min-1(vc=66m/min), v f=480mm/min(fz=0.034mm/t), ap×ae=9×0.1mm Coolant:wet
Comparison of finishing performance EPSF
EPSF Conventional
Comparison of surface Comparison of surface roughness
0
0.2
0.4
0.6
0.8
1
1.2
1.4
Rz(
μm
)
Axial directionFeed direction
Excellent machined surfacewith few burrs on top
Comparison of tool life by side milling. EPSM
Cutting example by side milling. EPSM
Comparison of tool life by side milling. EPSW
Work material : Inconel-718 (46HRC)
Tool : Square type φ8×4NTn=1,200min-1(vc=30m/min), v f=140mm/min(fz=0.03mm/t)ap×ae=8×0.3mm, OH=24mmCoolant : wet
ap
ae
0
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0 5 10 15 20
Cutting distance (m)
Vb(㎜)
Conventional
After 7m
After 7m
EPSM4080-24-PN
EpochEpoch Multi
Work material : 15-5PH
Tool : Square type φ8×4NT, n=3,200min-1(vc=80m/min), v f=500mm/min(fz=0.04mm/t),ap×ae=3×1mm, OH=24mm, Coolant : wet
ap
ae
EPSM4080-24-PN
After 1.5 hours milling end mill still can be used for further application. Even in 15-5PH cutting.Vb=0.06mmVb=0.06mm
After 1.5hour useEPSM4080-24-PN
Work material : SUS304
Tool:Wave-form type φ8×4NT,n=5000min-1(vc=125m/min), v f=800mm/min(fz=0.04mm/t),ap×ae=8×3mm, OH=24mm, Coolant : Wet
0.15
0.1
0.05
00 10 20
ap
ae
Conventional A
Conventional B
Cutting distance (m)
EPSW4080-24-PN
Vb(㎜)
EpochEpoch Wave
Field data
Comparison of tool wear by slotting. EPSM
Comparison of tool life wear by slotting. EPSM-CR
Work material : SUS304
Tool:Square type φ8×4NT,n=4,200min-1(vc=108m/min), v f=230mm/min(fz=0.014mm/t),ap×ae=6.4×8mm, OH=24mm, Coolant : Wet, Cutting distance : 4m
ap
ae
EPSM4080-PNEPSM4080-PN Conventional A
Rake face
Relief face
Rake face
Relief face
Work material : SUS304
Tool:Radius type φ8×r1n=2,200min-1(vc=55m/min), v f=260mm/min(fz=0.3mm/t),ap×ae=8×8mm Coolant : Wet
Cutting distance (m)
Conventional A
Corner radius
Conventional B
Conventional C
0 2 4 6 8 10 12 14
Interrupted cutting is possible
Broken
Normal wear
Chipping occuredChipping occured
Chipping occuredChipping occured
EpochEpochMulti
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
Dim
ensions,S
US
Multi
Dim
ensions,S
US
FinishD
imensions,
SU
S W
aveFeatures
Cutting condition
Re-grinding
Technical Data
EPSF/EPSM / EPSW-PN
New Produc t News No.1201E-8 2020-10
Epoch SUS series
2020-10(K)2012-1:FP
Attentions on Safety
2. Cautions regarding mounting(1) Before use, check the outside appearance of the tool for scratches, cracks, etc. and that it is firmly mounted in the collet chuck, etc.(2) If abnormal chattering, etc. occurs during use, stop the machine immediately and remove the cause of the chattering.
4. Cautions regarding regrinding(1) If regrinding is not performed at the proper time, there is a risk of the tool breaking. Replace the tool with one in good condition, or perform regrinding.(2) Grinding dust will be created when regrinding a tool. When regrinding, be sure to attach a safety cover over the work area and wear safety clothes such as safety
goggles, etc.(3) This product contains the specified chemical substance cobalt and its inorganic compounds. When performing regrinding or similar processing, be sure to handle the
processing in accordance with thelocal laws and regulations regarding prevention of hazards due to specified chemical substances.
1. Cautions regarding handling(1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands.
3. Cautions during use(1) Before use, confirm the dimensions and direction of rotation of the tool and milling work material.(2) The numerical values in the standard cutting conditions table should be used as criteria when starting new work. The cutting conditions should be adjusted as
appropriate when the cutting depth is large, the rigidity of the machine being used is low, or according to the conditions of the work material.(3) Cutting tools are made of a hard material. During use, they may break and fly off. In addition, cutting chips may also fly off. Since there is a danger of injury to
workers, fire, or eye damage from such flying pieces, a safety cover should be attached when work is performed and safety equipment such as safety goggles should be worn to create a safe environment for work.
(4) There is a risk of fire or inflammation due to sparks, heat due to breakage, and cutting chips. Do not use where there is a risk of fire or explosion. Please caution of fire while using oil base coolant, fire prevention is necessary.
(5) Do not use the tool for any purpose other than that for which it is intended.
Specifications for the products listed in this catalog are subject to change without notice due to replacement or modification. Printed in JAPAN
Printed using vegetable oil ink.
The diagrams and table data are examples of test results, and are not guaranteed values.“ ” is a registered trademark of MOLDINO Tool Engineering, Ltd.
Official Web Site
Database for selection Cutting Tool Products 【TOOL SEARCH】
http://www.moldino.com/en/Head OfficeHulic Ryogoku Bldg. 8F, 4-31-11, Ryogoku, Sumida-ku, Tokyo, Japan 130-0026International Sales Dept. : TEL +81-3-6890-5103 FAX +81-3-6890-5128
MOLDINO Tool Engineering Europe GmbHItterpark 12, 40724 Hilden,Germany. Tel +49-(0)2103-24820 Fax +49-(0)2103-248230
MOLDINO Tool Engineering (Shanghai), Ltd.Room 2604-2605, Metro Plaza, 555 Loushanguan Road, Changning Disctrict,Shanghai, 200051, China Tel +86-(0)21-3366-3058 Fax +86-(0)21-3366-3050
MITSUBISHI MATERIALS U.S.A. CORPORATIONDETROIT OFFICE Customer service41700 Gardenbrook Road, Suite 120, Novi, MI 48375-1320 U.S.A.Tel +1(248) 308-2620 Fax +1(248) 308-2627CHICAGO OFFICE1314B North Plum Grove Road, Schaumburg, IL 60173 U.S.A. Tel +1(847) 252-6371 Fax +1(248) 308-2627
MMC METAL DE MEXICO, S.A. DE C.V.Av. La Cañada No.16, Parque Industrial Bernardo Quintana, El Marques, Querétaro, CP 76246, MéxicoTel +52-442-1926800
Search Web
DISTRIBUTED BY:
Europe
China
America
Mexico
MMC METAL DO BRASIL LTDA. Rua Cincinato Braga, 340 13° andar.Bela Vista – CEP 01333-010 São Paulo – SP ., Brasil Tel +55(11)3506-5600 Fax +55(11)3506-5677
MMC Hardmetal (Thailand) Co.,Ltd. MOLDINO Division622 Emporium Tower, Floor 22/1-4, Sukhumvit Road, Klong Tan, Klong Toei, Bangkok 10110, ThailandTEL:+66-(0)2-661-8175 FAX:+66-(0)2-661-8176
Hitachi Metals (India) Pvt. Ltd.Plot No 94 & 95,Sector 8, IMT Manesar ,Gurgaon-122050 , Haryana, India Tel +91-124-4812315 Fax +91-124-2290015
Thailand
Brazil
India
Epoch SUS Finish, Epoch SUS Multi, Epoch SUS Wave
Additional lineup of Epoch SUS Finish for finishing.(size : φ3.0~12.0 36 items)
Top Related