Sediment Sampling in Sand-bed Rivers
Jean J. Peters, Brussels, Belgium Consulting engineer Prof. VUB & UCL
Methods & Instruments
Content • Importance of sediment data in rivers • General principles and some criticisms • Development of sediment measuring devices • Measurement in sand-bed rivers with Delft
Bottle and BTMA: experiences and how to have the feed-back from the practitioners to manufacturers
• Conclusions and recommendations
Why to get sediment data?
• We do not have yet sufficient understanding of sediment transport processes, especially in morphologically dynamic sand-bed rivers
• Worldwide, there is a pressing need for solving engineering questions (modelling?)
• Modelling requires, besides good input data, also the best possible understanding of the processes
Content • Importance of sediment data in rivers • General principles and some criticisms • Development of sediment measuring devices • Measurement in sand-bed rivers with Delft
Bottle and BTMA: experiences and how to have the feed-back from the practitioners to manufacturers
• Conclusions and recommendations
About principles
• The traditionally accepted theories about sediment transport distinguish only between bed load and suspended load, though adding sometimes “saltation”
• Most research in sediment transport was organised with artificial sediment, single diameter and uniform specific weight
• Sediment transport in rivers is much more complicated …
About principles
• Suspended sediment transport is usually determined by multiplying a measured sediment concentration with the local velocity (of the flow), which is not really the determination of the transport rate
• Bed load transport is seldom measured, because its measurement is said to be too difficult and too uncertain
Content • Importance of sediment data in rivers • General principles and some criticisms • Development of sediment measuring devices • Measurement in sand-bed rivers with Delft
Bottle and BTMA: experiences and how to have the feed-back from the practitioners to manufacturers
• Conclusions and recommendations
Development of sediment devices
• Direct measurement requires sampling • Sediment samplers were developed mainly
during the first half of the 20th century • Indirect measurement of sand transport has
not been quite successful, yet (ADCP ?) • The demand for samplers is very limited
and manufacturing is often by official organisations (FISP, Nanjing Automation)
Content • Importance of sediment data in rivers • General principles and some criticisms • Development of sediment measuring devices • Measurement in sand-bed rivers with Delft
Bottle and BTMA: experiences and how to have the feed-back from the practitioners to manufacturers
• Conclusions and recommendations
Delft Bottle & BTMA
• Samplers designed in The Netherlands for studying sand and gravel transport in Dutch rivers having limited depths and velocities
• Shape and efficiency of samplers were studied in laboratory (Delft and Zurich)
• Design changed by successive manufacturers for manufacturing reasons, not because of feed-back by users
Delft Bottle suspended mode
• The design of the body remained almost the same; however the technology for making the body has been adapted
• The original suspension mode was modified
Delft Bottle suspended mode • Original design of
Delft Bottle, used in Congo river (sampler procured in 1959, photo from 1971)
• Next slide is the present design, taken over by Eijkelkamp from Van Essen so that same body can be used on a frame
Delft Bottle mounted on frame • The design was
completely modified, especially the system to fix the bottle to the frame
• For different reasons, the nozzle elevation above the river bed may be wrong, inducing large errors
Delft Bottle mounted on frame • The picture (Bangladesh,
1994, Brahmapoutra River) shows the small front plates on which the sampler rests on the bottom, instead of the “skis” from the original design
• The sampler on frame has become much taller, requiring larger davits
Bedload Transport Meter Arnhem • The design of this
bedload sampler was modified, some changes were improvements, other not
• The sampler is much more secure than the Helley-Smith which was derived from it (see slide further)
Bedload Transport Meter Arnhem • Original design, 1971,
Congo River; although the sampler was not conceived for very large streams, it could be used successfully in water depths of up to 30 meters and velocities of more than 2 m/s
• The frame was loaded with lead strips
Experiences with DG & BTMA Jamuna river - Bahadurabad 28/05/94
0100200300400500600700800900
1000
0 50 100 150
Sediment transport rate (m³/m.day)
Elev
atio
n ab
ove
bed
(cm
)
Vert 1Vert 2Vert 3Vert 4
Experiences with DG & BTMA Jamuna river - Bahadurabad 28/05/94
0100200300400500600700800900
1000
0 100 200 300 400
Sediment particle size D50(µm)
Elev
atio
n ab
ove
bed
(cm
)
Vert 1Vert 2Vert 3Vert 4
Experiences with DG & BTMA Jamuna river - Vertical 3
0
100
200
300
400
500
600
700
800
900
1000
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
Sand transport rate (m3/m.day)
Elev
atio
n ab
ove
bed
(cm
)
Experiences with DG & BTMA Jamuna river - Vertical 3
0100200300400500600700800900
1000
0 100 200 300 400 500
Sediment particle size (µm)
Elev
atio
n ab
ove
bed
(cm
)
D35D50D65
Experiences with DG & BTMA Jamuna river - Vertical 3
0.0
10.0
20.0
30.0
40.0
50.0
0 100 200 300 400 500
Sediment particle size (µm)
Elev
atio
n ab
ove
bed
(cm
)
D35D50D65
Content • Importance of sediment data in rivers • General principles and some criticisms • Development of sediment measuring devices • Measurement in sand-bed rivers with Delft
Bottle and BTMA: experiences and how to have the feed-back from the practitioners to manufacturers
• Conclusions and recommendations
Conclusions & Recommendations • Direct sampling can be done with traditional
instruments such as Delft Bottle and BTMA • Direct sampling is needed to measure both the
transport rate and the sediment size distribution in the water column, especially near the bed
• More data are needed to check the existing theories about sediment transport processes and combing direct and indirect measurement may help tremendously
Conclusions & Recommendations • There is a need for closer collaboration between
the users and the manufacturers of equipment • Manufacturers need to give the correct and
detailed information about the instruments and their use
• Organisations such as IAHR and WMO can help the users by organising comparison between different instruments and by editing manuals and guidelines that must be specific to the various river environments
Top Related