Page 1 of 62
व्यावसाययक परीक्षण यरपोर्ट (प्रारंयिक) संख्या@No: PT-115/895
COMMERCIAL TEST REPORT माह@Month: September, 2018
(INITIAL) Validity: 31.08.2021
INITIAL COMMERCIAL TEST
SAMYAK ST 960 POWER TILLER
िारत सरकार Government of India
कृयष एवं यकसान कल्याण मंत्रालय
Ministry of Agriculture and Farmers Welfare
कृयष, सहकायरता एवं यकसान कल्याण यविाग Department of Agriculture, Cooperation and Farmers Welfare
दयक्षणी के्षत्र कृयष मशीनरी प्रयशक्षण एवं परीक्षण संस्थान Southern Region Farm Machinery Training and Testing Institute
ट्रैक्र्र नगर, गालटयदने्न - 515 731, यिला: अनंतपुर (आं. प्र.) Tractor Nagar, Garladinne - 515 731, District: Anantapur (A.P.)
[An ISO 9001:2015 CERTIFIED INSTITUTE]
Website: http://srfmtti.dacnet.nic.in/
E-mail: [email protected] Tele./FAX: 08551-286441
PT-115/895
SAMYAK ST 960 POWER TILLER
COMMERCIAL
(ICT)
SOUTHERN REGION FARM MACHINERY TRAINING & TESTING INSTITUTE,
ANANTAPUR, (A.P.)
Page 2 of 62
Manufacturer
:
M/s. Samyak Motors Pvt. Ltd.,
No. 3/34 C, Athipalayam Main Road,
Athipalayam, Coimbatore – 641 110,
Tamil Nadu, India.
Applicant : The Manufacturer
Indigenous/ Imported : Indigenous
SAMYAK ST 960 POWER TILLER
Report No.: PT-115/895 Month: September Year: 2018
Government of India
Ministry of Agriculture and Farmers Welfare
Department of Agriculture, Cooperation and Farmers Welfare
Southern Region Farm Machinery Training and Testing Institute
Tractor Nagar, Garladinne - 515 731, District: Anantapur (A.P.) [An ISO 9001:2015 CERTIFIED INSTITUTE]
Telephone No. 08551-286441 Fax No.08551-286441
Website: http://srfmtti.dacnet.nic.in/ E-mail: [email protected]
PT-115/895
SAMYAK ST 960 POWER TILLER
COMMERCIAL
(ICT)
SOUTHERN REGION FARM MACHINERY TRAINING & TESTING INSTITUTE,
ANANTAPUR, (A.P.)
Page 56 of 62
18.16 Salient Observations:
18.16.1 Engine Performance:
i) The backup torque of engine is 12.16 %, under natural ambient
condition.
ii) The maximum power was observed as 9.1 kW & 8.9 kW under
natural & high ambient condition respectively.
iii) The specific fuel consumption corresponding to maximum power was
recorded as 239 g/kWh against the declared value of 285 g/kWh.
iv) The specific fuel consumption corresponding to rated power was
observed as 234 g/kWh against the declared value of 270 g/kWh.
v) The maximum torque was recorded as 47.58 Nm against declared
value of 44.0 Nm under natural ambient condition.
18.16.2 Rotary shaft performance:
i) The maximum and rated rotary shaft power was measured as 7.5 &
7.4 kW respectively.
ii) The specific fuel consumption corresponding to power at rated engine
speed was measured as 265 g/kWh against the declared value of 315
g/kWh.
iii) The maximum equivalent rotary shaft torque was observed as 367.2
Nm against the declared value of 380 Nm.
18.16.3 Mechanical Vibration:
The amplitude of mechanical vibration on most of controls /
measuring points of the power tiller exceeded the limit of 100 micron.
The mechanical vibration is directly concerned with Operator’s Health, Safety and Comfort; apart from the useful life of the
machine’s components. In view of the above, this should be taken
care for corrective action.
18.16.4 Noise measurement:
Max. Noise at operator’s ear level and by stander’s position was observed as 95 dB(A) and 82 dB(A). The noise observed at operator's
ear level is more than the limit specified by IS12239 (Part3) : 1988.
The Sound Pressure Level is directly influencing the Operator’s Health, Safety and Comfort; and therefore warrants the corrective
action.
18.16.5 Haulage test
18.16.5.1 The power tiller was recommended for haulage test with a trailer of
gross mass of 1.0 tonne.
PT-115/895
SAMYAK ST 960 POWER TILLER
COMMERCIAL
(ICT)
SOUTHERN REGION FARM MACHINERY TRAINING & TESTING INSTITUTE,
ANANTAPUR, (A.P.)
Page 57 of 62
18.16.5.2 Distance traveled per litre was observed 12.01 to 12.15km.
18.16.5.3 Specific fuel consumption was observed 82.29 to 83.26 cc/km/t.
18.16.6 Puddling test
18.16.6.1 Puddling test was conducted with cage wheels and with hatchet blade.
18.16.6.2 The maneuverability of power tiller during puddling test was found
satisfactory.
18.16.6.3 On partial dismantling of the power tiller and inspection of the oil
samples from engine, crankcase, transmission case and rotary chain
case, no entry of mud and/water was observed in the rotary shaft
bearing cap.
18.16.7 Rotary blades:
i) The hourly rate of wear of blades for dry land and wet land
operations was observed as 0.13 to 0.31 percent and 0.16 to 0.37
percent respectively.
ii) Manganese & silicon content of straight blade, Carbon and silicon
contents of hatchet blades do not conform to IS 6690:1981
(Reaffirmed 2012). This should be looked into for corrective action.
iii) The dimensions of straight blades conform to the requirement of IS
6690:1981 (Reaffirmed 2012), whereas dimensions do not conform
for hatchet blade.
iv) The hardness of straight and hatchet of blades conforms the
requirement of IS 6690:1981 (reaffirmed 2012). This should be
looked into for corrective action.
18.16.8 As per IS 12239 (Part 3) : 1988, “maximum safe speed” with trailer is required to be specified by the manufacturer. Necessary action may
be taken in this regard.
18.16.9 As per IS 12239 (Part 3) : 1988, balancing mass to be added to
achieve correct weight balance of the power tiller with various
attachments should be recommended by the manufacturer in the
operator manual. This may be examined for compliance.
18.16.10 Provision of spark arresting device may be considered for
incorporation in the exhaust system.
18.16.11 Two metallic labeling plates, one is riveted on timing cover & other
plate is riveted on tool bar. Whereas provided metallic plates should
be as per IS 10273:1987.
PT-115/895
SAMYAK ST 960 POWER TILLER
COMMERCIAL
(ICT)
SOUTHERN REGION FARM MACHINERY TRAINING & TESTING INSTITUTE,
ANANTAPUR, (A.P.)
Page 59 of 62
19.4 18.16.13 We will interact with our supplier to meet the requirements for
handle grip as per IS 11858-1986.
19.5 18.17 Fuel saving tips and farmer tips will be included in future manual.
APPENDIX – I
BRIEF SPECIFICATION OF IMPLEMENTS USED
DURING FIELD TEST
Sl. No. I t e m Rotavator
1. Make & Model SAMYAK
2. Supplied by SAMYAK
3. No. of blades 20 + 20
4. Type of rotary blades Hatchet + Straight
5. Spacing of rotary blades (mm) 28 to 32
6. Overall dimensions (mm):
- Length 815
- Width 790
- Height 640
7. Gross mass (kg) 100
APPENDIX –II
BRIEF SPECIFICATION OF CAGE WHEEL
Sl. No. I t e m Cage wheel
1. Type Plate
2. Dia., (mm) 700/725
3. Width, (mm) 320
4. No & Type of lugs 16 + 8 & Rectangular plate
5. Size of lugs, (mm) 20.5 x 10.5 x 12.5/215 x 155 x4.0
6. Spacing of lugs, (mm) 130/285
7. Weight of each cage wheel, (kg) 25.0
Top Related