Rotary Controlled Trailing Edge DimmerInstallation Instructions
S-Classic E32V250T
For your safety
DANGERHAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH• It is illegal for persons other than an
appropriately licensed electrical contractors or other persons authorized by legislation to work
• To comply with all safety standards, the product must be used only for the purpose described in this instruction and must be installed in accordance with the wiring rules and regulation in the location where it is installed.
• There are no user serviceable parts inside the product.
Failure to follow these instructions will result in death or serious injury.
DANGERHAZARD OF ELECTRIC SHOCK• Hazardous voltage and electrical current may
be present at the wire leads of this product even
• Lock out and tag the input circuit before accessing the wiring connections.
Failure to follow these instructions will result in death or serious injury.
NOTICEEQUIPMENT DAMAGE HAZARD• Install the device according to instructions in this
document.•
diagrams related to the installation.• Do not use this product for any other purpose
• Two or more dimmers cannot be connected in parallel or series to control the same load from
• The product is suitable for indoor use only.• Install an IEC60898-1 compliant 250 V a.c. 6 A
type C MCB as overload protection, which has a special use for the dimmer.
Failure to follow these instructions can result in equipment damage.
Product features• Complies with IEC Safety and EMC Standards.• Full short-circuit protection.• Inbuilt over-current protection.• Supports dimming of two loads individually.• Compatible with dimmable LED lamps.• Adjustable minimum brightness setting.
Parameter
Nominal operating voltage 240 V a.c.
Nominal operating frequency 50 Hz
Max. / Min. load See Load compatibility
Wiring capacity
Dimming technique Trailing edge phase control
Mounting centers 60.3 mm
Compliance IEC 60669-2-1
Load compatibility
Symbol Load type Max. load Min. load
Dimmable LED lighting
100 W
(Max. 10 LEDs)
10 W
Incandescent lighting
240 V a.c. halogen lamps
250 W 10 W
Low voltage halogen lighting with electronic transformers
250 VA 10 VA
Installation
Wiring diagram (single load installation)
2 1 L
L
LL
L
N
N
240 V a.c.50 Hz
Dimmer
MCB
Wiring diagram (dual load installation)
2 1 L
L
LL
L
L L
N
NN
240 V a.c.50 Hz
Dimmer
Switch (optional)
MCB
Installing the dimmer
! "
$§
L 1 2
L 1 2
Min. brightness adjustment
Isolate power,lock and tag
ON
OFF
L L240 V a.c.
50 Hz
Installation steps:1 Isolate power to the input circuit.
2 Wire the dimmer terminal block according to the wiring diagram.
3 Switch the load on and turn the dimmer control fully counter-clockwise (lowest brightness). Now adjust the minimum brightness control on the back of the dimmer mechanism to set the lowest load
4 Secure the dimmer to the wall box using appropriate fasteners, then insert the screw caps into the holes on the front of the plate.
Operation
Single load operation
Dual load operation
L1L1 L1
L2L2L2L2 L2
Selectedload
Selectedload
Optionalswitch
Customer care
Warranty informationThis product is guaranteed for a period of 12 months from date of delivery, against any defect in construction or operation arising from faulty design, materials or workmanship.
It is the customer’s responsibility to ensure that the return is delivered to Schneider Electric with claim form duly completed. Should there be no product failure found or product failure is due to customer misuse or negligence, the replacement, labor and logistics costs will be charged to the customer.
Schneider Electric Industries (Malaysia) Sdn BhdCustomer Care: 1-800-880-877 or 603-7883 6333
Email: [email protected]
www.schneider-electric.com
Schneider Electric reserves the right to change
other information in this catalogue are correct, no warranty is given in respect thereof and the company shall not be liable for any error therein.
© Schneider Electric 2018
This material is copyright under international laws. Except as permitted under the relevant law, no part of this work may be reproduced by any process without prior written permission of and acknowledgement to Schneider Electric.
PHA31875 February 2018
1.0 mm - 2.5 mm2 2
Top Related