7/28/2019 Queen Size Bed Plans
1/27
Queen size bed plans
Plans for a bed with queen size size mattress (60"x80", 152x203 cm)
This page is optimized for viewing on the computer. For printing all thedrawings to take to the workshop, use thePrinter optimized format.Depending on how many drawings you want per page, play with the paperorientation and scale settings under page setup in your browser.
These plans are in Metric units. You can generate imperial dimensions byloading the SketchUp model into SketchUp, and setting the units to imperialunder "Model Info". However, the sizes are all rounded to be even millimeters,so the units will not work out to nice even values in fractional inches.
Bed postsThe bed posts are made by gluing two 2x4's flat against each other, and then
cutting out a 6x6 cm section.
http://woodgears.ca/bed_frame/queen_plan/print.htmlhttp://woodgears.ca/bed_frame/queen_plan/print.htmlhttp://woodgears.ca/bed_frame/queen_plan/print.htmlhttp://woodgears.ca/bed_frame/queen_plan/print.html7/28/2019 Queen Size Bed Plans
2/27
7/28/2019 Queen Size Bed Plans
3/27
The knobs at the top of the posts are turned by putting the entire post into the
lathe. If you don't have a lathe with a very long bed, you may wish to make the
knobs separately, and glue them onto the posts. This looks almost as good.
The illustration of the bed below is rendered with tapered posts instead ofturned posts. You can explore what the bed looks like with tapered posts
instead of turned posts by turning on the "sawed posts" layer and hiding the
"turned posts" layer.
7/28/2019 Queen Size Bed Plans
4/27
7/28/2019 Queen Size Bed Plans
5/27
Headboard
The headboard is doweled together with 5/8" dowels. Do not cut the profiles
into the edges of the pieces until you have dry fit. Once dry fit, cut the slots
and the chamfers on the inside edges with a router, and carve the chamfers
all the way into the corner with a knife or chisel.
7/28/2019 Queen Size Bed Plans
6/27
7/28/2019 Queen Size Bed Plans
7/27
7/28/2019 Queen Size Bed Plans
8/27
To get the shape of the panel, just trace out the outline from the dry fit
assembly onto a piece of plywood, and offset the outline by the depth of the
slot cut on the inside edges of the panels.
7/28/2019 Queen Size Bed Plans
9/27
Footboard
The footboard is made of two pieces of wood glued side to side. It is too wide
to be able to make out of one piece of lumber
7/28/2019 Queen Size Bed Plans
10/27
7/28/2019 Queen Size Bed Plans
11/27
Bed rails and slats
The bed rails have a hardwood ledge screwed and glued to the bottom edge,
which is used to hold up the slats.
The slats are tapered towards the end to allow them to sit lower in the bed,giving more room for the mattress.
7/28/2019 Queen Size Bed Plans
12/27
7/28/2019 Queen Size Bed Plans
13/27
Bed rail clips
This view shows how the bed rail clips fit into everything. The bed rail clips
allow for easy disassembly if the bed needs to be moved.
Alternatively, you can fasten the rails with large pocket holes, like I did whenIbuilt this bed. to avoid having to buy bed rail clips.
http://woodgears.ca/queen_size_bed/assembly.htmlhttp://woodgears.ca/queen_size_bed/assembly.htmlhttp://woodgears.ca/queen_size_bed/assembly.htmlhttp://woodgears.ca/queen_size_bed/assembly.html7/28/2019 Queen Size Bed Plans
14/27
Fasteners
Putting the bed together
Here you can see how therails finally meet the post.
With the dowels slightly
tapered, and the holes
flared out, these insert
relatively easily, and should
still be manageable even if
there is expansion or
contraction in the wood
from humidity changes.
I used three 3.5" #10 woodscrews to screw the rail tothe post. This is probably abit overkill. I'm happy withthe results though. Its
7/28/2019 Queen Size Bed Plans
15/27
probably at least as strong as using bed rail clips, as I did forthis bed, andless costly too.
It does unfortunately meanthat a screwdriver isnecessary to disassemblethe bed for moving. Thoughthe bed rail clips are notwithout their drawbackseither. Every time I havehad to take the other bedapart, I ended up having touse a rubber mallet to popopen the hooks.
http://woodgears.ca/bed_frame/build.htmlhttp://woodgears.ca/bed_frame/build.htmlhttp://woodgears.ca/bed_frame/build.htmlhttp://woodgears.ca/bed_frame/build.html7/28/2019 Queen Size Bed Plans
16/27
Finally, it was time to makethe slats. I cut most ofthese out of 10' 2x6's,because four of these couldbe cut out of one 10' 2x6
without any scrap.
I tapered the ends of theslats, so that they would sita little lower in the bed.With 13 slats to trim onboth sides, I now have 26of these funny shapedwedges lying behind mybandsaw.
And finally,putting it alltogether. I'mrather pleasedwith the result.
And all for lessthan $100 inmaterials.
All theequipment inthe back of myshop isonmobilebases, so I
could roll it outof the way forassemblingthis bed. My
presentbasement workshopis much better than myold workshopthat way.
http://woodgears.ca/mobile_base/index.htmlhttp://woodgears.ca/mobile_base/index.htmlhttp://woodgears.ca/mobile_base/index.htmlhttp://woodgears.ca/mobile_base/index.htmlhttp://woodgears.ca/workshop/basement.htmlhttp://woodgears.ca/workshop/basement.htmlhttp://woodgears.ca/workshop/basement.htmlhttp://woodgears.ca/workshop/index.htmlhttp://woodgears.ca/workshop/index.htmlhttp://woodgears.ca/workshop/index.htmlhttp://woodgears.ca/workshop/index.htmlhttp://woodgears.ca/workshop/basement.htmlhttp://woodgears.ca/mobile_base/index.htmlhttp://woodgears.ca/mobile_base/index.html7/28/2019 Queen Size Bed Plans
17/27
I didn't leave it together forlong though. The next stepwas to varnish it. I made avery short temporary bedrail to hold the head and
footboard upright againsteach other whilevarnishing. The bed railsthemselves I varnishedseparately on workbench.That way, I didn't run therisk of inadvertently gluingthe pieces together with
varnish.
Also note the printing on the back of the headboard. The plywood came froma shipping crate that Nortel had shipped to Research in Motion back around2002. It was made with some very nice plywood. It's the same plywood I usedfor this otherbed of similar design,
Making the bed rails
I made the bed rails from
2x10's. Unfortunately,
some of the 2x10's I boughtwere noticeably cupped. All
the 2x10's in the stack at
the lumber store had flaws
in them, and these were the best I could find.
In an ideal world, I would just have used my 12" jointer to flatten the board, butin the real world, I only have a6" jointer, so that wasn't an option.
http://woodgears.ca/bed_frame/build.htmlhttp://woodgears.ca/bed_frame/build.htmlhttp://woodgears.ca/bed_frame/build.htmlhttp://woodgears.ca/jointer/index.htmlhttp://woodgears.ca/jointer/index.htmlhttp://woodgears.ca/jointer/index.htmlhttp://woodgears.ca/jointer/index.htmlhttp://woodgears.ca/bed_frame/build.html7/28/2019 Queen Size Bed Plans
18/27
So instead I used a small3" power planer to planedown the edges a little bitso that the resulting boardwas approximately flat,
though not a smoothcontiguous surface.
I then passed the boardsthrough the jointer, with the
just-flattened side down toflatten up the other side.
After that, I flipped theboards, and planed anothermillimeter off the side I hadflattened with the hand-heldpower planer, at which
point I had a continuous smooth and flat surface on both sides.
The bed rails need to have a ledge on the bottom edge to hold the slats. Thisledge fits into a rabbet cut into the bottom side ofthe rails. I cut this rabbet in two steps. I don'toften use afeatherboard, but for this large piece,really helped, because I couldn't always push thelarge board against the push stick as Imaneuvered it over the saw.
I glued someblocks of
http://woodgears.ca/delta_saw/featherboard.htmlhttp://woodgears.ca/delta_saw/featherboard.htmlhttp://woodgears.ca/delta_saw/featherboard.htmlhttp://woodgears.ca/delta_saw/featherboard.html7/28/2019 Queen Size Bed Plans
19/27
hardwood between the rail and the ledge. These ensure that the slats of thebed will not slide side to side. They also serve to help hold the ledge in placebecause they are firmly glued to both the ledge and the rail itself.
As further reinforcement, I screwed the ledge in place with some 2" drywall
screws screwed through the ledge from the bottom, and into the bed rail.
For each the ledge, I apiece of hardwood 4 x 1.8cm and 2 meters long for. I
didn't have any pieces ofhardwood that length lyingaround and wanted tomake use of some uglyscraps of maple instead.So I finger joined somepieces end to end using
mybox joint jig. I spaced the fingers such that the width of a thin kerf bladewas just right for a tight joints.
These joints set rigid surprisingly fast on account of the large glue area.
I then glued the strip ofhardwood to the bottomedge of the rails, makingsure it made good contacteverywhere. That ledgehas to hold the weight ofwhatever is in the bed.
http://woodgears.ca/box_joint/jig.htmlhttp://woodgears.ca/box_joint/jig.htmlhttp://woodgears.ca/box_joint/jig.htmlhttp://woodgears.ca/box_joint/jig.html7/28/2019 Queen Size Bed Plans
20/27
One of the finger joints, asit looks on the bottom ofone of the rails. For goodmeasure, I also put a screwin every 50 cm or so, but
didn't photograph thatstep.
I drilled two holes into the ends of the rails, where I then glued short pieces ofdowel into the ends of them. These pieces of dowel protrude about 2 cm, andmate with the holes drilled into the posts. I tapered the dowels a little on thebelt sander, to make them easier to insert into the holes on the posts. These
dowels are meant to transfer the vertical load from the bed rails onto theposts.
Pocket holes to join the rails
7/28/2019 Queen Size Bed Plans
21/27
Next I glued some plugs into the rails
near the ends. These plugs are
positioned to be at the end of some
pocket holes yet to be cut. They are
there to help reinforce the wood
where the screw goes. After gluing in
these plugs, I drilled another set of
holes just behind the plugs to be the
pocket part of the pocket holes.
To help me align the drill for
drilling the screw hole part of thepocket holes, I made a temporary
drill-aiming guide, which I just
held against my drill by hand. Thetop edge of this drill is flat and
parallel with the axis of the drill
itself, so that provided a good
reference surface.
With the aiming guide held to the
top of the drill, I can make surethat the drill is aimed correctly so
that it will drill into the middle of
the pocket. My aiming guide was
really only good for getting the
vertical alignment right, but forhorizontal component was easy
enough to eyeball from above.
7/28/2019 Queen Size Bed Plans
22/27
After I drilled the pocket holes, Ichiseled open the pockets a bit
more, and then used the tip of a
3/8" drill to form a slightcountersink at the bottom of the
pockets.
After that, I routed the top edges
of the bed rails to the same profile
that I used for the headboard and
footboard.
The wood wasn'tperfect, and there
was one spotwhere I inserted a plug before routing the edges. That defect is on the inside,
facing the mattress, so only the top edge of the board is visible when it'sassembled. The plug hides the defect rather nicely.
Joining bed posts to the headboard
Next it was
time to join the
headboard to
the legs. Idrilled five
dowel holes
into the ends
of the
headboard
with a hand
drill. The
headboard is
way too wide
for me to get it
into a drill press. I suppose I could have usedthis trickto drill the holes into
the ends, but I would have had to rig up some extra high support for my drill
press to even do that. So instead, I just clamped it to a work bench, with
http://woodgears.ca/shop-tricks/drilling-big.htmlhttp://woodgears.ca/shop-tricks/drilling-big.htmlhttp://woodgears.ca/shop-tricks/drilling-big.htmlhttp://woodgears.ca/shop-tricks/drilling-big.html7/28/2019 Queen Size Bed Plans
23/27
spacers under it to bring it to the right height so that one of my hand drills,
upside down on the bench drilled just horizontal into the piece.
This helps guide the drill, but some of the holes were not quite as straight as Ihad hoped, but still better than I did on the last bed that I had built. So maybe Ishould have rigged up the drill press, or maybe usedthis jig.
Next I transferred the holepositions to the posts,using much the sameapproach I had used on the
headboard. Again, I offsetthe post by half the width ofa hole, so I could justtransfer the hole's edgeposition for my centers inthe post's holes.
I could put the posts on mydrill press, so these holeswere easy to get straight.
To compensate for a few ofthe holes being slightlycrooked, I tapered one sideof the dowels that I put intothose holes on the beltsander.
http://woodgears.ca/horizontal_boring/jig.htmlhttp://woodgears.ca/horizontal_boring/jig.htmlhttp://woodgears.ca/horizontal_boring/jig.htmlhttp://woodgears.ca/horizontal_boring/jig.html7/28/2019 Queen Size Bed Plans
24/27
I then stuckthe head andfootboards
together, justto see how itwould look. Ididn't glue theposts onto thehead andfootboards yetthoughbecause I stillneeded to routthe final profile
onto the top edges of the headboard and footboard.
Also note how the footboard is styled similar to the headboard, but shorter,and without panels. All the steps for the footboard are the same as theheadboard, except that it's simpler and lacks panels.
The next step was to route a nice round onto the top of the headboard. I useda 1/2" round router bit, though I didn't use the whole of the quarter roundcurvature because I wanted to still have just a bit of an edge on the board.
7/28/2019 Queen Size Bed Plans
25/27
This view better shows thecurve that I routed onto theboard.
I left routing the curve until
quite late in the process sothat if I ended up bangingor nicking the top edge ofthe headboard orfootboard, it would be in thepart of the wood to berouted away.
Before gluing the posts to the head and footboard, it was time to drill the holesfor mounting the bed rails onto the posts. These consisted of slanted pilotholes for my giant pocket hole screws, and two 3/4" alignment peg holes. Toget the angle for the slanted holes, I put the post on a wedge on the drillpress. Tilting the drill press table would not have worked because the way ittilts, the drill press's column would have interfered with where I needed to putthe post.
7/28/2019 Queen Size Bed Plans
26/27
I flared out the openings ofthe holes for the alignmentpins to the bed rails. Theseholes accept the pegs atthe ends of the bed rails
(more on that later).
Finally, I was ready to mate the posts onto the headboard. Note how the
second and fourth dowel from the left appear to be just a bit crooked. That'sbecause they were, and I tapered the one side of them so that they'd fit in thestraight hole on the post. I made sure the post fit perfectly to the headboardbefore I put any glue on anything.
7/28/2019 Queen Size Bed Plans
27/27
For clamping on the posts,I didn't have any clampslong enough to span thewidth of the headboard. Soinstead, I firmly clamped a
piece of wood to the middleof the headboard, and put aclamp on it stretching to thefar end. I then used thatpiece of wood to clampagainst with my 3 foot barclamps.
Top Related