8/22/2019 Photoresists for Microlithography.pdf
1/18
Photoresists for
Microlithography
Smitha .c.k
1821210010
8/22/2019 Photoresists for Microlithography.pdf
2/18
INTRODUCTION
The construction of most modern electronic
gadgets like computers, television, etc. is based
on microlithography.
Microlithography deals with patterning of
electronic circuitry at micron or sub-micron
level and enables one to make Very Large Scale
Integrated Circuits (VLSI).
8/22/2019 Photoresists for Microlithography.pdf
3/18
The Conventional Lithographic
Technique In the lithographic process the substrate is first coated with some
oxide layer and a radiation sensitive polymer film (resist) isdeposited on it .
The substrate is then exposed to light through a mask..
The transparent part of the mask allows light/radiation to passthrough and the other opaque part blocks it.
Photochemical reactions change the chemical and physicalproperties of the exposed regions of the film.
By utilizing these changes of properties a pattern is developed,based on the difference in the solubilities of the exposed andunexposed regions.
8/22/2019 Photoresists for Microlithography.pdf
4/18
Kodak thin film resist (KTFR).
It was composed of cyclized rubber (poly cis-
isoprene) and a bis-azide (2,6-bis (4-
azidobenzal)-4-methylcyclohexanone)
Using this resist the dimensions of the
semiconductor device reached up to
2micrometers
8/22/2019 Photoresists for Microlithography.pdf
5/18
DNQ-Novolak Photoresist
The negative tones of KTFR had high sensitivityand were easy to handle
negative photoresist had loss of resolution due toswelling of resist film during development with
organic solvents, which moreover also caused
environmental pollution.
Gradually the positive photoresists began to
dominate the market .
8/22/2019 Photoresists for Microlithography.pdf
6/18
Positive DNQ-NOVOLAK photoresists soonbecame the real workhorses of thesemiconductor fabrication industry.
Modified forms of this resist are still usedcurrently.
These consist of a photoactive compound viz.2,1-Diazonaphthaquinone-5-sulfonic acidesterified with 2,3,4 trihydroxybenzophenone ina polymer matrix like novolak resins
which are polymers of cresols or other phenoliccompounds with formaldehyde
8/22/2019 Photoresists for Microlithography.pdf
7/18
8/22/2019 Photoresists for Microlithography.pdf
8/18
Upon irradiation with UV light, the substituteddiazonaphthaquinone undergoes the Wolff rearrangement andforms a ketene.
The ketene then reacts with water to form the 1-indene carboxylicacid making the exposed part of the resist soluble in the alkalinedeveloper.
In the unexposed regions, however, the diazonaphthaquinoneremains unchanged.
If we develop the film with base then the resist in the exposed partgets washed out due to solubility of indene carboxylic acid.
The unexposed part, however remains insoluble thus when they aredeveloped patterns are obtained.
8/22/2019 Photoresists for Microlithography.pdf
9/18
The mechanism of action of negative photoresistsis mainly based on insertion/crosslinking reactionof reactive nitrene intermediate obtained from
the bisazide photoactive component withcyclized rubber
This make the exposed regions more insoluble by
increasing the molecular weight.
Hence when developed a negative image isobtained.
This contrasts with positive photoresists wherethe exposed parts are made more soluble.
8/22/2019 Photoresists for Microlithography.pdf
10/18
8/22/2019 Photoresists for Microlithography.pdf
11/18
Chemically Amplified Resists
Optimizing Novolak higher resolutions areachievable
newer photoresists are being considered, asDNQ-Novolak resist cannot be used at
lower wavelength mainly because of tworeasons:
1) The substituted DNQ absorbs UV light
very intensely as we go down to lowerwavelength of radiation, resulting in a loss ofpattern.
8/22/2019 Photoresists for Microlithography.pdf
12/18
The quantum yield of the DNQ-Novolak resists is verylow.
The third generation of photoresists for deep UV (DUV)was developed by C G Willson of Texas University.
Here the main components are a photoinactive polymerwith an acid labile pendant ester group and photoacidgenerators (PAG).
When light falls on the resist, PAG generates an acid, which
hydrolyses the ester group of the polymer film and makesthe exposed part of the resist soluble in the alkalinedeveloper
8/22/2019 Photoresists for Microlithography.pdf
13/18
8/22/2019 Photoresists for Microlithography.pdf
14/18
These resists are called chemically amplified (CA) resists, since theconcentration of acid increases by the photochemical reaction.
The amplification of acid by chemical reaction during the postexposure baking shoots up the quantum yield even above one.
In CA resists the main resist film is photo-inactive, so no strongabsorption of light beam and it is possible to design hightransmittance acid labile polymers in deep UV regions.
The large polarity change brought about by acid catalyzed reactionsin the exposed and unexposed parts give high contrast in CA resist.
After C GWillsons discovery of the first CA resist, there are now
hundreds of CA resists and different photoacid generators (PAG).
8/22/2019 Photoresists for Microlithography.pdf
15/18
DRAWBACKS
Unwanted acid diffusion into the unexposed parts.
The acid generated by photochemical reaction and the H+ ionsdeveloped during post exposure bake do not diffuse verticallyalone and so are not bound into the exposed parts only.
Acid diffusion into the unexposed parts has been overcome byusing base along with the polymer film itself.
The base however itself consumes the acid generated by thethermal reaction in the exposed part and this reduces the
resolution.
To avoid this the base itself should be photoactive so that thebasicity is lost in the exposed part by photochemical reaction andin the unexposed parts the basicity remains intact.
8/22/2019 Photoresists for Microlithography.pdf
16/18
Another major problem the CA resists sufferfrom is due to airborne contamination.
The resist film takes up the airbornecontamination of bases from paints of windows,
walls and adhesives that use additives likehexamethyldisilazane,N-methylpyrrolidone(NMP),which neutralizes the photogenerated acid in thesurface portion of the exposed regions.
So the surface skin gets neutralized and remainsinsoluble during development with base.
8/22/2019 Photoresists for Microlithography.pdf
17/18
One way to reduce this problem is the thoroughpurification of the enclosing atmosphere by usingactivated charcoal filters and protectiveovercoating.
Sulfonic acid esters, disulfones, etc. are mixedwith resist film for dual purposes.
On the one hand they work as additives to
promote the adhesion ofthe resist film with thesubstrate and on the other also react withairborne contamination and deactivate them.
8/22/2019 Photoresists for Microlithography.pdf
18/18
Thank you!!!
Top Related