Page �
Pilatus PC-12for FSX
FLIGHT SIMULATOR COMPATIBILITY AND SYSTEM REQUIREMENTS
This product is compatible with Microsoft Flight Simulator X (FSX). Microsoft FSX is required to use this software. For your computer, we recommend that you have at a minimum a 3GHz processor, �GB of system RAM (2GB preferred) and a 256MB video card. Low-end, on-board sound chips are NOT recommended. A plug-in sound card, such as a Soundblaster Audigy, is recommended. In some cases, sounds will not work correctly unless you have an adequate sound card. An Internet connection is required for product support and reinstalling your software.
Windows XP and Windows Vista are the official operating systems that are supported for use with the Flight� Software Pilatus PC-�2 for FSX.
Pilot's Guide
Page 2
TABLE OF CONTENTS
Jim Rhoads ................................................................................ Project Management and Panel Layout
Terry Gaff .............................................................................Aircraft Design, Gauge and Panel Graphics
Jerry Beckwith ............................................................................................................ Flight Dynamics
Ed Struyznski ....................................................................................................... Gauge Programming
Karl Gaff ..................................................................................................................................Sounds
Antje Aelken ..................................................................................................... German Voice Callouts
Todd Nicholson ............................................................................................................Documentation
CREDITS
Credits ............................................................. 2
Introduction ...................................................... 3
Important Information ....................................... 4
Reinstalling Your Software ................................. 5
Aircraft Data ..................................................... 6
Symbols and Abbreviations ................................ 7
Using the Configuration Manager ........................ 8
Selecting Your Aircraft ....................................... 9
Main Panel ................................................. 10-12
Pop-Up Panels ............................................ 13-14
Electronic Attitude Indicator ............................. 15
Electronic Horizontal Situation Indicator ............ 16
EFIS Controller ................................................ 17
Engine Instrument System ............................... 18
Autopilot ......................................................... 19
Altitude Preselector ......................................... 20
Transponder............................................... 20-21
Overhead Panel .......................................... 22-23
CAWS Panel .................................................... 23
CAWS Panel Warnings ................................ 24-25
Brake Panel .................................................... 25
Throttle Quadrant and Lower Panel ............. 26-27
Radio Stack................................................ 27-28
Aircraft Lighting and Doors .............................. 29
Limitations ................................................. 30-32
Emergency Procedures ............................... 32-33
Normal Procedures ..................................... 34-40
Performance Charts .................................... 41-45
Weight and Balance .................................... 46-48
Page 3
INTRODUCTION
Pilatus Aircraft Ltd. was founded in 1939 and is located in Stans, Switzerland. Pilatus is the largest and most experienced single engine turboprop manufacturer in the world.
Pilatus Aircraft enjoys a history of aviation excellence that covers both civilian and military markets. This history includes the design and production of high performance trainers, utility aircraft and most recently, the PC-12. The PC-12 is Pilatus's most recent move into corporate aviation and has been enthusiastically received. As deliveries have grown over the years, so has the PC-12's reputation. It is refined, versatile, and ultimately the most compelling choice of any aircraft in and around its class.
The PC-12 is a powerful combination of size, speed, economy and advanced design that allows the PC-12 to dominate where other aircraft struggle to compete. The PC-12's power and efficiency come from the Pratt and Whitney PT6A turboprop engine. Combined with the Swiss-engineered airframe it is able to offer a cruise speed of 270 knots and direct operating costs of around $300.00 per hour. With its large pressurized cabin and seating from 6 to 7 passengers, it offers anything from a perfect airborne conference room to a large and versatile freight hauler with a cabin of 330 cubic feet and a cargo door that measures 53 x 52 inches.
The PC-12 demonstrates wide opportunities for corporate, air ambulance, cargo, and regional work. It is a true Swiss army knife of the aviation industry.
On behalf of Flight1 Software and the PC-12 team members, I invite you to experience the Flight1 Software PC-12 for FSX and thank you for your continued patronage.
Jim Rhoads Flight1 Softwarewww.flight1.com
Page �
IMPORTANT INFORMATION
No part of this document may be reproduced in any form or by any means without the express written consent of Flight1 Software.
© 2007 Flight1 Software. All rights reserved.
Visit our Web Site at: www.flight1.com
DISCLAIMER
This software is designed for entertainment purposes only. Although we have designed the PC-12 for FSX to resemble and function as closely as possible the real PC-12, it is not designed as a training device. Not all systems have been simulated, and some of those that have been simulated may not be entirely functional or simulated to 100%.
About This User's Guide
Please read through this User's Guide to become familiar with the Flight1 Software PC-12 for FSX. The PC-12 for FSX includes many avionics and features that you will want to familiarize yourself with. Taking the time to do this now will allow you to get the most enjoyment out of your new software.
Even though this User's Guide is designed in color to make it easy to read on your computer screen, if you wish to print this User's Guide and save ink at the same time, please choose to print in Grayscale, via your computer’s print dialog screen.
Customer Support
Flight1 Software strives to provide timely, reliable support. The following support options are available:
l For support related to passwords, order numbers, and key files, please visit our Automated Support System at www.flight1.com/view.asp?page=service
l If you need further support related to one or more of items above, please use our Support Ticket System at www.flight1.com/ticket.asp
l For technical product support related specifically to the PC-12 for FSX software package, please visit our Technical Support Forum at www.simforums.com/forums/
Please note that the Support Ticket System should not be used for technical product support.
In the panel sections and the gauge sections, RED overlays represent gauge or feature descriptions and ORANGE overlays represent gauge click-spots.
Page 5
REINSTALLING YOUR SOFTWARE
Backing Up Your Original Download File and Your Key File
After you've installed your software, please take a moment to back up your original download file (the file you downloaded when you purchased the product - it has a red airplane icon and is labeled Flight One Purchasing Module) and your key file, both of which are saved to your hard disc in the folder that you specified before the download process. Both of these files should be backed up to a CD-Rom or a DVD-Rom so that you can reinstall the product in the future.
Reinstalling Your Software
1) Double-click the original download file (the Flight One Purchasing Module) to run the installation wrapper.
2) Make sure to temporarily turn off any anti-virus software and any other disc utilities that may be running in the background.
3) On the main installation wrapper screen, press the CLICK HERE TO REINSTALL button.
4) Ensure that your computer is connected to the Internet, then follow the onscreen prompts to select your key file and enter your password. Once your purchasing information is validated, the software will be extracted to your hard disc and the installation will start automatically.
5) After the installation completes, make sure to reboot your computer before running the software for the first time. This will ensure that any DLLs, fonts, etc, are registered with Windows and will ensure trouble-free use.
Click Hereto Reinstall
Do not back up the Extracted Program File that's located in your C:\Flight One Software folder. In most cases this file cannot be used to reinstall the product. If you reinstall the product using this file, you will most likely receive a license error when you run the software. Always be sure to back up and reinstall from the original file that you downloaded when you first made your purchase.
Page 6
AIRCRAFT DATA
Engine
Manufacturer and Type: Pratt & Whitney Canada Twin-Shaft Turboprop with Three-Stage TurbineModel Number: PT6A-67B
Horsepower Rating and Engine Speed
Takeoff Power: 1200 SHPMaximum Climb/Cruise Power: 1000 SHP
Propeller
Manufacturer and Type: Hartzell Hydraulically Actuated, Constant Speed, Full-Feathering and ReversibleNumber of Blades: 4
Fuel
Approved Fuels: Jet A, Jet A-1, Jet B, JP-4Total Capacity: 406.8 Gallons / 2736.5 Pounds (1540 Liters)Usable Fuel: 402 Gallons / 2703.6 Pounds (1521.5 Liters)
Oil
Total Capacity: 3.6 Gallons (13.6 Liters)
Maximum Weights
Maximum Ramp Weight: 9965 Pounds (4520 Kilograms)Maximum Takeoff Weight: 9921 Pounds (4500 Kilograms)Maximum Landing Weight: 9921 Pounds (4500 Kilograms)Maximum Zero Fuel Weight: 9039 Pounds (4100 Kilograms)
Maximum Cargo Weight
Baggage Area: 400 Pounds (180 Kilograms)Cabin Area: 3300 Pounds (1500 Kilograms)
Typical Aircraft Weights
Empty Weight: 5468 Pounds (2480 Kilograms)Useful Load: 4454 Pounds (2020 Kilograms)
Page �
SYMBOLS AND ABBREVIATIONS
V-Speed Symbols
VSO Stalling Speed or the minimum steady flight speed at which the aircraft is controllable in the landing configuration at maximum gross weight.
VS Stalling Speed or the minimum steady flight speed at which the aircraft is controllable.
VFE Maximum Flap Extended Speed is the highest speed permissible with wing flaps in a prescribed extended position.
VLE Maximum Landing Gear Extended Speed is the highest speed at which an aircraft can be safely flown with the landing gear down.
VA Maneuvering Speed is the maximum speed at which you may use abrupt control travel.
VNO Maximum Structural Cruising Speed is the speed that should not be exceeded except in smooth air, and then only with caution.
VNE Never Exceed Speed is the speed limit that may not be exceeded at any time.
VX Best Angle of Climb Speed provides the best altitude gain per unit of horizontal distance, and is usually used for clearing obstacles during takeoff.
VY Best Rate of Climb Speed provides the best altitude gain in the shortest amount of time.
VG Best Rate of Glide Speed provides the best glide distance in an engine-out scenario.
Airspeed Terminology
KCAS Knots Calibrated Airspeed is indicated airspeed corrected for position and instrument error and expressed in knots. Knots calibrated airspeed is equal to KTAS in standard atmosphere at sea level.
KIAS Indicated Airspeed in Knots.
KTAS True Airspeed is the speed of an aircraft relative to undisturbed air which is the CAS corrected for altitude, temperature and compressibility.
Meteorological Terminology
OAT Outside Air Temperature is the free air static temperature obtained either from in-flight temperature indications or ground meteorological sources, adjusted for instrument error and compressibility effects.
ISA Standard Temperature is 15°C at sea level pressure altitude and decreases by 2°C for each 1000 feet of altitude.
PA Pressure Altitude is altitude measured from the standard sealevel pressure of 29.92 in Hg by a pressure of barometric altimeter.
Page �
USING THE CONFIGURATION MANAGER
The Pilatus PC-12 Configuration Manager is a utility that is used to make a variety of changes to your PC-12 for FSX and is installed separately with your software. The Pilatus PC-12 Configuration Manager can be found in your Start Menu.
From the desktop - Start - All Programs - Flight One Software - Pilatus PC-�2 for FSX
l Make your configuration selection, then press the SaveSettings button to save your selections.
l After you save your selections, press the ExitCfgMngr button to exit.
l You can at any time press the ResetDefaults button to reset your configuration choices back to the default selections. After pressing the ResetDefaults button, make sure to save your settings so that they are reflected in Flight Simulator.
Choosing to include the copilot's glass instruments in the VC may cause performance issues on some computer systems.
Choose to include a speed bug on the airspeed indicator if you would like to take advantage of the auto-throttle capability of the autopilot.
Please note that Flight Simulator should NOT be running while using the Pilatus PC-12 Configuration Manager or any configuration selections made may not be saved correctly.
Page �
SELECTING YOUR AIRCRAFT
The Flight One Software Pilatus PC-12 for FSX is located under Pilatus in the Flight Simulator Aircraft Manufacturer drop-down box and under Flight One Software in the Flight Simulator Publisher drop-down box.
Choose from the following seven variants:l Cargo XA-PCMl Executive OE-EMCl Executive HB-FPAl Executive N523JLl Spectre 285l Standard C-FKVLl Standard RA-01500
If there is a problem loading the PC-12 for FSX into Flight Simulator, first load the default Flight Simulator flight, move the aircraft to the active runway, then save the flight as the new default flight. Load the new default flight, then SWITCH to the PC-12 for FSX (using the Aircraft drop-down selection in the Flight Simulator Menu Bar) and set up your flight parameters, such as location, time, weather, etc.
We strongly advise against loading the PC-12 for FSX over a previously saved flight, other than the Default flight. This will ensure that previously saved settings will not carry over and interfere with the PC-12 for FSX.
In order to see all available aircraft variants, make sure that "Show All Variations" is selected in the Flight Simulator aircraft selection screen.
Page �0
MAIN PANEL
Main Panel Layout
Overhead Pop-Up - Toggles the Overhead panel on and off.
Parking Brake Pop-Up - Toggles the Parking Brake panel on and off.
EADI/EHSI Pop-Up - Toggles the EADI/EHSI zoom gauges on and off.
Altitude Selector Pop-Up - Toggles the Altitude Preselector zoom gauge on and off.
Radio Stack Pop-Up - Toggles the Radio Stack on and off.
Throttle Quadrant Pop-Up - Toggles the Throttle Quadrant and lower panel on and off.
EFIS Controller Pop-Up - Toggles the EFIS Controller panel on and off.
CAWS Pop-Up - Toggles the CAWS panel on and off.
EIS Pop-Up - Toggles the EIS zoom panel on and off.
Overhead Pop-UpParking Brake Pop-Up
EADI/EHSI Pop-Up Altitude Preselector Pop-Up Radio Stack Pop-Up
Throttle Quadrant Pop-UpEFIS Controller Pop-Up
CAWS Pop-Up EIS Pop-Up
Continued on Next Page
Page ��
MAIN PANEL
The cockpit is of a conventional layout in that all of the controls, switches, and instruments are readily accessible to the pilot for single-pilot operation. The overhead panel contains the switches to control the electrical bus distribution, external lighting, de-icing, starting, and cabin heating and cooling systems. The instrument panel center console contains the CAWS annunciator panel, EFIS control unit, trim indicator, engine power controls, flap selector, cockpit and cabin lighting controls.
Main Panel Layout, Continued...
1) Flap Deflection Indicator2) Airspeed Indicator3) Standby Attitude Indicator4) NAV Indicator5) RMI6) Master Caution Indicator7) Master Warning Indicator8) EADI9) EHSI
10) Marker Beacon Indicators11) Altitude Preselector 12) Altimeter13) Selected NAV Indicator14) Vertical Speed Indicator15) Autopilot16) Transponder17) EIS (Engine Instrument System)
4
3
1
2
5
6 7
8
9
10
11
12
13
14
17
16
15
Continued on Next Page
Page �2
MAIN PANEL
Main Panel Gauge Click-Spots
All click-spots are activated using left mouse clicks, unless otherwise noted. Some click-spots (such as some rotary knobs) can be activated using your mouse's scroll wheel. Scroll forward to turn knobs to the right and scroll backward to turn knobs to the left. This includes all pop-up panels and related gauges, too.
1 2
3 4
5
8 9
1) OBS Adjust Left2) OBS Adjust Right3) Altitude Bars Decrease4) Altitude Bars Increase5) Toggle Digital Airspeed Display6) Increase Speed Bug7) Decrease Speed Bug8) Swap VOR1/ADF Button9) Swap VOR2/ADF Button10) Extinguish Master Caution11) Extinguish Master Warning12) Course Adjust Left13) Course Adjust Right
14) Heading Adjust Left 15) Heading Adjust Right 16) Marker Sensitivity Switch Up17) Marker Sensitivity Switch Down18) Altimeter Reset Button19) Altimeter Calibration Decrease20) Altimeter Calibration Increase21) DME 1/2 Swap Button22) NAV/GPS Swap Button23) Approach Mode Button24) AHRS 1/2 Swap Button25) Toggle Digital Vertical Speed Display
Not all main panel gauge click-spots are shown in this view. More information (including click-spots) for other gauges, such as the Altitude Preselector, EIS, Autopilot, etc, can be found in their specific sections beginning on page 15.
1312 1514
17
16
18 2019
21 22 23 24
25
7
6
10 11
Page �3
POP-UP PANELS
Keyboard Shortcuts and Pop-Up Panels
The different pop-up panels can be toggled on and off using keyboard shortcuts, in addition to the click-spots on the main panel.
l (Shift+2) EADI/EHSI Zoom Gaugesl (Shift+3) EIS Zoom Panell (Shift+4) Overhead Panell (Shift+5) Brake Panell (Shift+6) Radio Stackl (Shift+7) EFIS Controller
l (Shift+8) Throttle Quadrant and Lower Panell (Shift+9) Altitude Preselector Zoom Gauge
EADI/EHSI ZOOM GAUGES EIS ZOOM PANEL
OVERHEAD PANEL BRAKE PANEL
Continued on Next Page
Some pop-up panels feature an orange 'X' in the corner. Click on the 'X' to close the pop-up panel.
Page ��
POP-UP PANELS
Keyboard Shortcuts and Pop-Up Panels, Continued...
RADIO STACK EFIS CONTROLLER
THROTTLE QUADRANT AND LOWER PANEL ALTITUDE PRESELECTOR ZOOM PANEL
THIS SPACE INTENTIONALLY LEFT BLANK
Page �5
ELECTRONIC ATTITUDE INDICATOR
1) Autopilot Mode Indicators - The current active Autopilot modes are displayed in these two areas.
2) Speed Pointer - The Speed Pointer on the left-hand side of the display is controlled by the AOA system and is visible at all times.
3) Heading Tape - Aircraft heading is shown on the Heading Tape at the sky/ground border.
4) Fixed Aircraft Symbol - A fixed symbol in the center of the display is used as a reference point.
5) Sky Pointer - The Roll Attitude Scale is marked at 10, 20, 30, 45 and 60 degrees.
6) Heading Bug Indicator - Displays the current position of the Heading Bug. The Heading Bug Indicator is linked to the Heading Indicator on the EHSI.
7) Rising Runway - Present during an ILS approach. The Rising Runway symbol will start increasing in size at 200 feet and continue to increase in size to 0 feet.
8/9) Rate of Turn Pointer/Turn Scale - Provides rate of turn information based on yaw rate corrected for angle of bank.
10) Radio Altitude Indicator - Displays the current altitude from ground level.
11) Flight Director - Displays visual cues from the Autopilot to follow when hand-flying.
12) Glideslope Display - A glideslope scale and deviation pointer on the right-hand side and a runway symbol toward the bottom of the picture is displayed when an ILS frequency is selected and the EHSI course pointer is within 105° of the aircraft heading.
13) Decision Height Indicator - Displays the current Decision Height.
89
7
411
5
3 6
2
13
12
10
11
Not all features will be displayed on the EADI at all times. Some features, such as the Glideslope Display and the Rising Runway Display, will be displayed only under certain conditions.
Electronic Attitude Indicator Features
Page �6
7
85
11
45
8
963
1
2
6
1
4
2
11
10
93
ELECTRONIC HORIZONTAL SITUATION INDICATOR
1) Wind Speed and Vector Indicator - Indicates the wind direction and speed relative to the aircraft.
2) Primary Navigation Source - Indicates the navigation system selected as the primary navigation sensor.
3) Selected Course Display - Displays the selected course for the active navigation system.
4) To/From Arrow Indicator - Indicates if you are traveling to or from the selected navigation source, such as a VOR. An arrow pointing up indicates you are traveling toward the navigation source. An arrow pointing down indicates you are traveling away from the navigation source.
5) Symbolic Aircraft - Provides a visual reference of the airplane position in relation to the deviation bar. 6) Heading Bug - An orange heading bug is manually rotated around the compass scale by the heading
select knob on the control panel. The heading bug is used to indicate desired heading and provides selected heading reference for autopilot steering.
7) Range Display Ring - Display range indicator ranges from 2nm up to 50nm. Range display is available in both ROSE mode and ARC mode.
8) Course Deviation Display - Provides a reference for the course deviation bar to indicate the centerline of the selected navigation or localizer course in relation to the symbolic airplane.
9) Distance, Ground Speed and Time - Displays distance, current groundspeed, and time (ETE) to selected DME station in VOR mode or to waypoint in GPS mode. ETE option is selected via EFIS Controller.
10) Glideslope Display - A glideslope scale and deviation pointer on the right-hand side is displayed when an ILS frequency is selected.
11) Heading Indicator - Indicates the current heading that the heading bug is set to.
ARC
MODE
ROSE
MODE
The EHSI can provide 360° compass HSI (Rose Mode) and 120° arc sectored HSI (ARC Mode). The type of display is selected via the EFIS control panel.
Electronic Horizontal Situation Indicator Features
Page ��
ELECTRONIC HORIZONTAL SITUATION INDICATOR EFIS CONTROLLER
1) Decision Height Knob - Used to adjust the Decision Height as shown on the EADI. The decision height range is from OFF (0) to 2500 feet and will be displayed in ten-foot increments up to 2500 feet.
The EFIS Controller provides a number of different functions related to both the EADI and the EHSI.
EFIS Controller Functions and Click-Spots
1 1
3 34 13 1314
5 6 7 9
10 11 12
28
2) Decision Height Push-Knob - Push to turn the Decision Height Inidcator on the EADI ON and OFF. The Decision Height Indicator on the EADI is always displayed below 2500 feet.
3) Course Adjustment Knob - Used to adjust the Course Indicator on the EHSI.
4) Course Adjustment Push-Knob - Press the course adjustment knob to set the Course Pointer on the EHSI to the "direct" bearing of the current active NAV source (VOR only).
5) HSI Mode Selection - Press to change the EHSI display to ROSE mode. Press a second time to select MAP mode with Range Selection.
6) ARC Mode Selection - Press once to change the EHSI display to ARC mode. Press a second time to select MAP mode with Range Selection.
7) NAV Source Selection - Press to toggle between NAV mode and GPS mode. With the Autopilot in NAV mode, the aircraft will track the current navigation source, either NAV/LOC or GPS.
8) SYS REF - Press to toggle between ETE and Ground Speed displayed on the EHSI.
9) Range Display Increase - Press to increase the Range Display in EHSI MAP mode. Display Range Indicator ranges from 2nm up to 50nm.
10) System Bearing 1 Pointer Select - Press to sequentially select the next available navigation source. Choose from NAV1, GPS, ADF or OFF (Blank). The NAV 1 bearing pointer on the EHSI will point directly toward the current navigation source.
11) System Bearing 2 Pointer Select - Press to sequentially select the next available navigation source. Choose from NAV2, GPS, ADF or OFF (Blank). The NAV 2 bearing pointer on the EHSI will point directly toward the current navigation source.
12) Range Display Decrease - Press to decrease the range display in EHSI MAP mode. Display Range Indicator ranges from 2nm up to 50nm.
13) Heading Adjustment Knob - Used to adjust the Heading Bug on the EHSI.
14) Heading Adjustment Push-Knob - Press the Heading Adjustment Knob to "snap" the Heading Bug to the current aircraft heading.
Page ��
1) Engine Torque Indicator - Displays the current engine torque.
2) Inlet Turbine Temperature Indicator - Displays the current engine Inlet Turbine Temperature.
3) NG Indicator - Displays the current engine gas sensor speed.
4) RPM Indicator - Displays the current propeller RPM.
5) Outside Air Temperature Indicator - Displays the current Outside Air Temperature in Celcius.
6) Endurance Indicator - Displays the current aircraft range remaining in hours:minutes.
7) Fuel Quantity Indicator (LBS) - Displays the current total fuel quantity in pounds.
8) Fuel Flow Indicator (FL/H) - Displays the current fuel flow in Pounds Per Hour.
9) Fuel Used Indicator - Displays the total amount of fuel used in pounds. The Fuel Used Indicator can be zeroed out by pressing the Fuel Reset switch.
10) Fuel Quantity Indicator - Displays the fuel quantity remaining in each of the two fuel tanks.
11) Generator 1 Indicator (Amps/Volts) - Displays generator 1 DC Amps and DC Volts.
12) Date Indicator - Displays the current Flight Simulator date.
13) Generator 2 Indicator (Amps/Volts) - Displays generator 2 DC Amps and DC Volts.
14) Time Indicator - Displays the current Flight Simulator time.
15) Engine Oil Temperature and Pressure Indicators - Indicates Engine Oil Temperature in Celcius and Engine Oil Pressure in Pounds Per Square Inch (PSI).
16) Fuel Reset Switch - Press to reset the Fuel Used indicator to zero.
17) Test Switch - Press and hold to place the EIS in test-mode. Release to cancel test-mode.
ENGINE INSTRUMENT SYSTEM
The Engine Instrument System (EIS) is a computer-controlled system which receives input from the sensors. It displays engine and other system information and provides warnings when certain parameter limits are exceeded.
1412
96
85
1311
151311
1074
12
321
16 17
Engine Instrument System Functions and Click-Spots
Page ��
AUTOPILOT
The Autopilot installed in the PC-12 aircraft is the Bendix/King KFC 325 Digital Automatic Flight Control System (AFCS). The KFC 325 Digital AFCS has three axis controls: pitch, roll and yaw.
1) DN/UP - Controls the vertical axis of the Autopilot. The rocker switch function is dependent upon the Autopilot's active mode.
2) HDG - Engages the Heading Select mode. Heading information is received from the Heading Bug on the EHSI.
3) NAV - Engages the Navigation mode. The Flight Director will command tracking of the Coupled Navigation Receiver based on the EHSI selected Primary Navigation Source.
4) APR - Engages the Approach mode. APR mode will capture and track the selected localizer sensor with approach accuracy. APR mode provides both lateral (LOC) and vertical (GS) tracking.
5) BC - Engages the Back Course mode.
6) YD - Engages the Yaw Damper and Rudder Trim Relief independent of the Autopilot's pitch and roll axes.
7) AP - Engages the Autopilot. The Yaw Damper is automatically activated when the Autopilot is engaged; however, the Yaw Damper remains engaged if the Autopilot is disengaged.
8) ALT - Engages the Altitude Hold mode. Altitude Hold commands the aircraft to maintain the Pressure Altitude existing at the moment of selection.
9) IAS - Engages the Indicated Airspeed Hold mode. When the Airspeed Indicator with Heading Bug option is selected via the Configuration Manager, the Autopilot will automatically adjust the Power Control Lever (throttle) to match the speed input via the Speed Bug.
10) FD - Engages the Flight Director in Pitch Attitude Hold mode and Wings Level Mode. The pitch attitude of the Flight Director is synchronized to the current aircraft pitch attitude.
11) SOFT RIDE - Engages the Soft Ride mode. Soft Ride mode decreases the Autopilot gains thus decreasing the aggressiveness of the Autopilot resulting in a more comfortable ride in turbulent conditions (not modeled).
12) HALF BANK - Engages the Half Bank mode. The Autopilot's maximum commanded bank angle is reduced to one half of the normal value. This mode is provided to increase passenger comfort (not modeled).
13) TEST - Press to test the Autopilot Mode Lamps. When pressed, all Autopilot Mode Lamps should illuminate. Press a second time to cancel the test.
1
1
2 3 4 5 6 7
8 9 10 11 12 13
Autopilot Functions and Click-Spots
Page 20
ALTITUDE PRESELECTOR
1
23
4
4
1) ENG - Engages the Vertical Speed Hold mode when depressed while the Selected Vertical Speed is displayed.
2) ARM - Engages the Autopilot Altitude Arm mode when depressed while the selected Altitude is displayed. Altitude Select mode (ARM) will cancel the Autopilot Altitude Hold (ALT) mode if Autopilot Altitude Hold is already engaged. ARM mode should be active to ensure altitude capture.
3) PULL VS - Press to toggle between Altitude Mode and VS Mode.
4) SET - Press to increase or decrease the value in either Altitude Mode or VS Mode. Values are selected in 100 foot increments in both modes.
The Altitude Preselector will play an audible alert 1000 feet prior to your destination altitude, then again 300 feet prior to your destination altitude.
The Altitude Preselector provides both altitude and vertical speed input. The type of display is selected by pressing the Pull VS button.
1
23
4
4
TRANSPONDER
1
2 3
4
56
7
9
8
10
11 11 11 11 11 11 11 11 12 13
VS
MODE
ALTITUDE
MODE
Altitude Preselector Functions and Click-Spots
Transponder Functions and Click-Spots
In addition to its basic functions, the GTX 337 transponder also displays Pressure Altitude and features a Count-Up Timer, Altitude Monitor, and OAT and Density Altitude display.
1) IDENT - Press to activate SPI (Special Position Identification) pulse in the unit (simulated only). When pressed, IDENT text will appear at the upper left of the display and remain there for 18 seconds.
2) VFR - Sets the transponder code to 1200 when pressed. When pressed again, the previous code is restored.
Continued on Next Page
Page 2�
TRANSPONDER
Transponder Features and Click-Spots, Continued...
3) STBY - Selects the Standby mode. The Reply Symbol at the lower left of the display will disappear when in Standby mode.
4) ON - Powers the transponder up and starts the self test. POST (Power On Self Test) screen stays visible for 5 seconds after turning the transponder on. During this time no other buttons on the transponder will function.
5) ALT - Sets the transponder to Mode A and C, essentially giving altitude information as well as ID to interrogations. In Flight Simulator, altitude information is given automatically, regardless of transponder simulated.
6) OFF - Powers the transponder off.
7) FUNC - Changes between pages shown at the right side of the display. Current modes simulated are Pressure Altitude, Flight Time, Altitude Monitor, OAT/Density Altitude and Count Up Timer. See below for more information on the different functions.
8) CRSR - By left-clicking the CRSR button, transponder code entry is completely cancelled once started, but prior to last digit input.
9) START/STOP - Starts and stops the Count Up Timer by left-clicking the button. You must be on the Count Up Timer function page to start and stop the respective timer.
10) CLR - Moves code entry cursor back (to left) one digit during code entry by left-clicking. If cursor is returned to first code digit and CLR is left-clicked again, code entry is cancelled completely. Also resets the Count Up Timer by right-clicking when the appropriate function page is active. Note that Count Up Timer must be stopped for time clearing to work.
11) Numbers 0-7 - Used to enter transponder code by left-clicking. Clicking any button initiates code entry and number on button pressed will be first digit in code. When fourth digit is entered, new code will be activated.
12) Numbers 8-9 - Decreases (8) or increases (9) Altitude monitor number by 100 foot increments via left-click when Altitude Monitor function page is active.
PRESSURE ALT: Displays Pressure Altitude as Flight Level. FLIGHT TIME: The timer will start automatically after lift-off and turn off automatically on touch-down. Currently there is no CLR function built in. ALTITUDE MONITOR: Shows altitude to be monitored (100 feet - 900 feet in 100 foot increments) and specifies position relative to that altitude by showing ABOVE or BELOW indicator text. See description 12 (numbers 8-9 key section) above for setting the Monitor Altitude. OAT/DALT: Outside Air Temperature and Density Altitude. COUNT UP TIMER: Controlled by START/STOP and CLR buttons (see description 9 above). COUNT DOWN TIMER: Not Modeled.
Transponder Function Modes
Page 22
OVERHEAD PANEL
Even though all overhead switches and buttons function, not all overhead functions are simulated.
The Overhead Panel contains the switches and buttons to control the electrical bus distribution, external lighting, de-icing, starting and cabin heating systems.
1
1
1
2
2
2
2
2
2
2
2
3 3
4 5
7 8 9
10 10 11 13 14
7
12 15 15 17
16 16 18
16 16 19
20 20 21
20 20 22
23
6
1) TEST - Press to test each of the following: Overhead lamps (all lamps display), Stick Pusher (audible alarm) and Fire (audible alarm). Lamp test also tests CAWS lamps. Press again to cancel the test.
2) EXTERNAL LIGHTS - Press to turn ON or OFF the aircraft's various exterior lights.
3) FUEL PUMPS - Press to place the left-hand or right-hand fuel pumps in ON, AUTO or OFF mode.
4) STARTER - Press to engage the aircraft's Starter.
5) IGNITION - Press to turn the aircraft's Ignition to ON, AUTO or OFF mode.
6) AMP/VDC - Displays the current Amps and Volts load on the aircraft's electrical system.
7) GEN1/GEN2 - Switch to turn Generator 1 and/or Generator 2 ON and OFF.
8) BAT1 - Switch to turn the Battery ON or OFF. When BAT1 is switched ON or OFF, the Master Power switch will be switched ON or OFF as well.
9) EXT1 - Switch to turn External Power ON or OFF.
10) AV2/AV1 - Switch to turn the Avionics Busses ON or OFF. Both switches are tied together.
11) NON ESS OVRD - Switch to place Non Essential Bus Override into AUTO mode.
12) MASTER POWER - Switch to turn the aircraft's power ON or OFF. This turns off all aircraft systems.
13) INV - Switch to place the aircraft's Inverter to either Generator 1 or Battery power.
When a button is depressed, the corresponding lamp will illuminate, indicating the function is active. When a button is depressed again and turned off, the corresponding lamp will extinguish, indicating the function is turned off.
Overhead Panel Functions and Click-Spots
Continued on Next Page
Page 23
OVERHEAD PANEL
14) STBY BUS - Switch to turn the Standby Bus ON or OFF.
15) BOOTS - Press to turn the de-icing boots ON or OFF. Choose from 1-minute or 3-minute duration.
16) LH WSH/RH WSH - Press to turn on windshield heat. Choose from LIGHT (anti-fog) or HEAVY (anti-ice).
17) PROP - Press to turn ON propeller de-icing.
18) INERT SEP - Press to turn the Inertial Separator ON or OFF.
19) PROBES - Press to turn the pitot heat ON or OFF.
20) COOLING SYS - Press to turn the cooling system ON or OFF. When turned ON, choose Recirculated Air, Cool Air, Fan Speed High or Low and Vent/Flood.
21) PASS WNG NO SMKG - Press to turn the No Smoking sign ON or OFF.
22) SEAT - Press to turn the Seatbelt sign ON or OFF.
23) CABIN - Press to turn Cabin Heat ON or OFF.
The Central Advisory and Warning System (CAWS) integrates the control and display functions of aircraft systems status into a single unit.
A warning light is red and indicates a condition that requires an immediate corrective action by the pilot. It is accompanied by a voice callout and the master WARNING light will come on.
A caution light is amber and indicates a condition that requires a pilot's attention but not an immediate reaction. It is accompanied by the master CAUTION light coming on and an aural gong sounding.
An advisory light is either green or blue and indicates that a system is in operation.
CAWS PANEL
Overhead Panel Functions and Click-Spots, Continued...
Page 2�
CAWS PANEL WARNINGS
PASS DOOR Indicates main entry door and/or handle is not locked.
CAB DOOR Indicates cargo door and/or handle is not locked.
CAB PRESS Indicates cabin altitude above 10,700 ft or if the maximum pressure differential is exceeded.
AIR/GND Indicates a disparity between LH and RH AIR/GND switch inputs to the Stick Pusher computers.
PROP LOW P Indicates propeller has gone to a low pitch (below minimum in-flight pitch) with aircraft not on the ground.
A/P TRIM Indicates autopilot and/or auto trim failure.
ESNTL BUS Indicates voltage of the Bat, Gen 1, or Gen 2 busses less than 22 VDC.
AV BUS Indicates avionic busbar 1 or 2 voltage less than 22 VDC.
STAB TRIM Indicates stabilizer trim is unsafe for takeoff (on ground only).
OIL QTY Indicates low engine oil quantity (engine not running).
ENG FIRE Indicates over temperature condition and/or possible engine fire.
GEN 2 OFF Indicates that generator 2 is off-line.
BUS TIE Indicates generator 1 bus tie isolation relay is open.
PUSHER Indicates Stall Warning/ Stick Pusher System malfunction.
FIRE DETECT Indicates a malfunction in the engine fire detection circuit.
GEN 1 OFF Indicates that generator 1 is off-line.
INVERTER Indicates inverter output less than 20 VAC.
BAT HOT Indicates a battery over-temperature or temperature sensor disconnected.
FLAPS Indicates a flap system failure (mechanical or electrical).
CHIP Indicates metal particles in the engine oil system.
CAWS FAIL Indicates a CAWS internal failure.
BAT OFF Indicates a battery is off-line.
FUEL PRESS Indicates fuel system pressure is less then 2 psi. Extinguishes when fuel system pressure is greater than 3.5 psi.
HYDR Continuously illuminated in flight indicates low hydraulic pressure.
ECS Indicates Environmental Control System malfunction.
AOA DE ICE Indicates AOA de-ice malfunction or DE ICING PROBES switch set to OFF.
N ESNTL BUS Indicates non essential busbar voltage less than 22 VDC.
L FUEL LOW Indicates fuel quantity in left wing tank has reached 20 US gal.
A/P DISENG Indicates autopilot pitch and aileron servos disengaged.
DE ICE
BOOTS
INERT SEP Indicates an inertial separator door operation failure.
STATIC Indicates a static port heater failure.
R FUEL LOW Indicates fuel quantity in right wing tank has reached 20 US gal.
BATTERY Indicates a battery over voltage or over current condition.
OIL QTY Indicates low engine oil quantity, engine running (non operative).
WSHLD HEAT Indicates a windshield heating system failure.
PITOT 1 Indicates a pilot pitot head heater failure.
Indicates a pressure sequence failure.
Continued on Next Page
Page 25
CAWS WARNINGS
From the Brake Panel, you can access the Airspeed Reference Sticker, the Hobbs Meter, the Emergency Locator Transmitter, the Parking Brake and the Clock.
1
1
2
3 54
1) ELT - Switch to turn the ELT ON, ARMED and to TEST/RESET the ELT.
2) PARKING BRAKE - Press to turn the Parking Brake handle and either release or engage the Parking Brakes.
3) RESET - Press to Reset the Elapsed Time.
4) CLOCK - Press to cycle through the different Clock modes. Choose from Local Time, GMT Time and Elapsed Time.
5) START/STOP - Press to Stop or Start the Clock Timer.
6) Hobbs Meter - Displays the total accumulated engine time.
7) Airspeed Reference Sticker - Conveniently displays the most common airspeed references.
BRAKE PANEL
PITOT 2 Indicates a copilot pitot head heater failure.
PROP DE ICE Indicates a propeller de-ice system failure.
L FUEL PUMP Indicates left fuel boost pump is opening.
A/P TRIM Indicates autopilot trim is operating.
PUSHER
ICE MODE
DE ICE
BOOTS
PASS OXY Indicates adequate pressure of oxygen to the passenger masks.
R FUEL PUMP Indicates right fuel boost pump is operating.
Indicates that the pusher computer is set to ice mode.
Indicates de-ice boots operating and pressure sequence correct.
7
6
Brake Panel Functions and Click-Spots
CAWS Panel Warnings, Continued...
Page 26
1) Gear Lamps - Visually display whether the retractable landing gear is down and locked (Green) or transitioning (Red).
2) Flood Light - Press to turn the flood light ON and OFF in the 2D cockpit. The cockpit flood light in the VC is controlled via the separate Flood Light switch on the center console, behind the throttle lever.
3) Silencer - Press to mute audible alerts. Press again to unmute audible alerts.
4/5) Landing Gear Up/Down - Press to cycle the landing gear up (4). Press to cycle the landing gear down (5). The landing gear lever is inoperative on the ground.
6) Autotrim Indicator - Displays the current trim attitude of the aircraft in roll, yaw and pitch.
7) Autotrim Indicator Pop-Up - Press to pop up a larger version of the Autotrim Indicator.
8) Cabin Temperature Display - Displays the current Cabin Temperature in Celcius.
9/10) Stab Trim Up/Down - Press to trim the aircraft's nose down (9). Press to trim the aircraft's nose up (10).
11/12) Manual Override Lever - Press and hold to move the Manual Override Lever toward MAX (11). Press and hold to move the Manual Override Lever toward OFF (12). When the Manual Override Lever is in the OFF position, you have full manual control of the Power Control lever. When you move the Manual Override lever toward the MAX position, the Throttle Control lever will automatically slowly advance to MAX and you will no longer have manual control. To regain manual control, move the Manual Override Lever to the OFF position.
13/14) Power Control Lever - Press and hold to increase the Power Control Lever toward MAX (13). Press and hold to decrease the Power Control Lever toward GROUND (14). Continuing to press and hold will bring the Power Control Lever into the REVERSE position.
THROTTLE QUADRANT AND LOWER PANEL
From the Throttle Quadrant and Lower Panel, you can access the aircraft's engine controls, flaps, landing gear and trim functions.
Throttle Quadrant and Lower Panel Functions and Click-Spots
Continued on Next Page
6
9
10
8
17
18
15
16
13
14
11
12
4
5
1
3
7
2
In addition to the click-spots shown, you can click and hold each handle, then drag the Manual Override lever, the Power Control lever and the Condition lever.
Page 2�
15/16) Condition Lever - Press and hold to move the Condition Lever up toward FLIGHT IDLE (15). Press and hold to move the Condition Lever down toward GROUND IDLE (16). Continuing to move the Condition Lever down will place the Condition Lever in the CUT OFF/FEATHER position.
17/18) Flap Lever - Press to move the Flap Lever up (17). Press to move the Flap Lever down (18). Flap positions are 0º (full up), 15º, 30º and 40º (full down). The current flap position is displayed on the Flap Position Gauge on the main panel.
THROTTLE QUADRANT AND LOWER PANEL
Throttle Quadrant and Lower Panel Functions and Click-Spots, Continued...
RADIO STACK
Radio Stack Functions and Click-Spots
The Radio Stack features a Garmin GMA 340 Audio Panel, two Garmin GNS 430 GPSs (GPS 1 and GPS 2), a Bendix/King KR 87 ADF Receiver and a Garmin MX200 Multi-Function Display (MFD). The CAWS panel has also been included for convenience.
7
1
2
3
4
5
6
8
10
11
1) Garmin GMA 340 Audio panel2) Garmin GNS 430 GPS with COM 1 and NAV 13) Garmin GNS 430 GPS with COM 2 and NAV 24) Bendix/King KR 87 ADF Receiver5) Garmin MX200 MFD6) CAWS Panel7) Press to enlarge the GNS 430 GPS 1.8) Press to enlarge the GNS 430 GPS 2.9) Press to close the Radio Stack.10) Press to enlarge the MX200 MFD.11) Press to enlarge the CAWS panel.
Pilot's Guides for both the Garmin GNS 430 GPS and the Garmin MX200 MFD have been installed separately with your software. These Pilot's Guides can be found in your Start Menu.
From the desktop - Start - All Programs - Flight One Software - Pilatus PC-�2 for FSX
Features and click-spots for the audio panel and the ADF receiver can be found on the next few pages.
9
Continued on Next Page
Page 2�
1) FRQ - Press to swap Standby and Active ADF frequencies.
2) OFF/VOL - Press to turn the ADF receiver ON and OFF.
3) Press to increase whole second frequency number.
4) Press to increase whole third frequency number.
5) Press to increase fractional frequency number.
6) Press to decrease whole second frequency number.
7) Press to decrease whole third frequency number.
8) Press to decrease fractional frequency number.
RADIO STACK
GMA 340 Audio Panel Functions and Click-Spots
1) PILOT - Press to turn the Audio Panel ON and OFF.
2) MKR MUTE - Press to MUTE audible marker alerts.
3) SENS - Press to adjust the marker sensitivity.
4) COM 1 - Press to hear to COM 1 audio.
5) COM 1 MIC - COM 1 microphone button.
6) COM 2 - Press to hear to COM 2 audio.
7) COM 2 MIC - COM 2 microphone button.
8) NAV 1 - Press to hear NAV 1 audible idents.
9) NAV 2 - Press to hear NAV 2 audible idents.
10) DME - Press to hear DME audible idents.
11) ADF - Press to hear ADF audible idents.
12) COM 1/2 - Press to hear both COM 1 and COM 2 audio simultaneously.
13) SPKR - Speaker audio button.
14) PA - PA audio button.
15) PILOT - Pilot audio button.
16) CREW - Crew audio button.
17) TEST - Press and hold initiate lamp test. All lamps should illuminate. Release to cancel lamp test.
18) COPILOT - Press to turn the Audio Panel ON and OFF.
1 18
2
3
4 6 8 9 10 11 17
5 7 121513
14 16
KR 87 Functions and Click-Spots
1 2
5
6
3 4
7 8
Although all buttons have click-spots and the indicator lamps function, not all features are simulated.
Page 2�
AIRCRAFT LIGHTING AND DOORS
1
1
2
2
456
3
3
Gauge backlighting in both the 2D cockpit and the VC is controlled directly via Flight Simulator and comes on and turns off based on the time of day. The cockpit flood light in the VC is controlled via the separate Flood Light switch on the center console, behind the throttle lever.
Exterior Lighting Map
1) Beacon Lights2) Strobe Lights3) Navigation Lights4) Recognition Lights5) Landing Lights
6) Taxi Light7) Wing Light (Pilot's Side Only)8) Cabin Door (Shift-E)9) Cargo Door (Shift-E+2) - Battery Must Be ON10) Direct View Window (Shift-E+3)
7
Exterior and Interior Lighting Controls
TAXI - Turns the nose gear Taxi light ON and OFF.
LANDING - Turns the main gear Landing lights ON and OFF.
WING - Turns the Wing light ON and OFF. This is visible on the pilot's side only.
NAV - Turn the Navigation lights ON and OFF.
STROBE - Turn the wing Strobe lights ON and OFF.
BEACON - Turns the Beacon lights ON and OFF.
RECOG - Turns the wing Recognition lights ON and OFF.
LOGO - The Logo lights are not modeled.
10
8 9
3
Page 30
LIMITATIONS
Airspeed Limitations
Maneuver Limits
This airplane is certificated in the Normal Category. The Normal Category is applicable to aircraft intended for non-aerobatic operations. These include any maneuvers incidental to normal flying, stalls (except whip stalls), lazy eights, chandelles, and turns in which the bank angle does not exceed 60°. Aerobatic maneuvers, including spins, are not approved.
Do not exceed this speed in anyoperations. Refer to VMO schedule
for maximum speed above 15200 ft.
Do not make full or abrupt controlmovements above this speed.
Do not exceed this speed with flaps extended.
Do not retract or extend the landing gearabove this speed.
Do not exceed this speed withlanding gear extended.
240 236
0.48
161 158
158 155
154 121
148 145
144 141
140 137
136 133
132 129
127 124
123 120
165 163
130 130
180 170
240 236
Maximum Operating Speed
- VMO
- MMO
Maximum OperatingManeuvering Speed - VO
9921 lb (4500 kg)
9480 lb (4300 kg)
9039 lb (4100 kg)
8380 lb (3800 kg)
7940 lb (3600 kg)
7500 lb (3400 kg)
7060 lb (3200 kg)
6610 lb (3000 kg)
6170 lb (2800 kg)
5730 lb (2600 kg)
Maximum Flap ExtendedSpeed - VFE
<=15º
>15º
Maximum Landing GearOperating Speed - VLO
Maximum Landing GearExtended Speed - VLE
AIRSPEED KCAS KIAS SIGNIFICANCE
Flight Load Limits with Flaps Up +3.3 g, -1.32 g Flight Load Limits with Flaps Down +2.0 g, -0.0 g
Continued on Next Page
Page 3�
LIMITATIONS
Airspeed Indicator Markings
Red Lineor
Red/WhiteNeedle
Green Arc
White Arc
Maximum operating limit (VMO / MMO)
Normal operating range. Lower limit is maximum weight stall speed in the clean configuration (VS). Upper limit is the
maximum operating speed (VMO / MMO).
Full flap operating range. Lower limit is maximum weight stall speed in landing configuration (VSO). Upper limit is maximum
speed with full flaps extended (VFE).
236 or 0.48Mwhichever is
lower
91 to 236
64 to 130
MARKING KIAS VALUE REMARKS OR RANGE
Engine Operating Limits
The limits presented in each column shall be observed. The limits presented do not necessarily occur simultaneously.
TAKEOFF
MAX CONT. CLIMB/CRUISE
MINIMUM IDLE
STARTING
TRANSIENT
MAX REVERSE
1200
1000
900
44.34
36.95
61.00
34.25
800
760
750
100
870
760
104
104
50.7 G.I.64 F.I.
140
1700
1700
1870
1650
90 to 135
90 to 135
60 Minimum
200 Maximum
40 to 200
90 to 135
10 to 110
10 to 110
-40 to 100
-40 Minimum
-40 to 100
10 to 105
OPERATINGCONDITION
SHP TORQUEPSI
MAXITT ºC
Ng%
NpRPM
OILPRESS PSI
OILTEMP ºC
G.I. = Ground Idle
F.I. = Flight Idle
Continued on Next Page
Page 32
Power Plant Instrument Markings
LIMITATIONS
Engine Speed (Ng)
ITT
Oil Temperature
Oil Pressure (PSI)
Torque (PSI)
N/A
N/A
N/A
40/60
N/A
N/A
N/A
N/A
60 to 90
N/A
60 to 104%
400 to 760 ºC
10 to 105 ºC
90 to 135
0 to 36.9
N/A
760 to 800 ºC
105 to 110 ºC
N/A
36.9 to 44.3
104%
800/1000 ºC
110 ºC
135/200
44.3/61
REDDIA/RADMin. Limit
YELLOWARC
Caution
GREENARC
Normal
YELLOWARC
Caution
REDRAD/DIAMax. Limit
EMERGENCY PROCEDURES
The procedures listed in this section are taken directly from the actual Pilatus PC-12 Pilot’s Operating Handbook. Although we have designed the Flight1 Software Pilatus PC-12 for FSX to resemble and function as closely as possible the real PC-12, it is not designed as a training device. It’s possible that some checklist procedures listed may not be accomplished in this simulation.
The recommended action to be taken in case of failure or in emergency simulations is contained in this section. Some situations require rapid action, leaving little time to consult the emergency procedures. Prior knowledge of these procedures and a good understanding of the aircraft system is a prerequisite for safe aircraft handling.
Know your aircraft and be thoroughly familiar with important emergency procedures.
The emergency procedures use the terms — "Land as soon as possible" and "Land as soon as practical". For the purpose of these procedures the meanings are as follows:
l Land as soon as possible - Land without delay at the nearest airport where a safe approach and landing is reasonable assured.
l Land as soon as practical - Landing airport and duration of flight are at the discretion of the pilot. Extended flight beyond the nearest suitable airport is not recommended.
General
Page 33
[ ] PCL ..................................................................................................................FULL FORWARD[ ] Manual Override Lever ........................................ PULL UPWARDS AND MOVE SLOWLY FORWARD
TO ACHIEVE REQUIRED ENGINE POWER
If engine fails below 50% Ng or accelerates very slowly with ITT at limit (870 ºC/20 seconds) or compressor stall:
[ ] Starter ....................................................................................................PUSH FOR 2 SECONDS[ ] Accelerate Ng > 80% ..................................................................................................... CHECK
[ ] PCL .................................................................................................................................. IDLE[ ] Reverse .............................................................................................................. AS REQUIRED[ ] Braking ............................................................................................................... AS REQUIRED
If the aircraft cannot be stopped in the remaining runway:
[ ] PCL .................................................................................................................................. IDLE[ ] Condition Lever ...........................................................................................CUT-OFF / FEATHER[ ] Fuel Emergency Shut Off ............................................ PRESS LATCH DOWN AND PULL LEVER UP[ ] Master Power Switch .................................................................................................. OPERATE
After the aircraft has stopped - Evacuate
Airspeeds for Emergency Operations
All airspeeds are with aircraft in clean configuration under ISA conditions.
EMERGENCY PROCEDURES
Rejected Takeoff
Engine Failure
Best Glide (Propeller Feathered)
9921 lb (4500 kg) 114 KIAS
9039 lb (4100 kg) 110 KIAS
8380 lb (3800 kg) 106 KIAS
7720 lb (3500 kg) 102 KIAS
7060 lb (3200 kg) 97 KIAS
6400 lb (2900 kg) 93 KIAS
Operating Maneuvering Speed (VO)
9921 lb (4500 kg) 158 KIAS
9480 lb (4300 kg) 155 KIAS
9039 lb (4100 kg) 151 KIAS
8380 lb (3800 kg) 145 KIAS
7940 lb (3600 kg) 141 KIAS
7500 lb (3400 kg) 137 KIAS
7060 lb (3200 kg) 133 KIAS
6610 lb (3000 kg) 129 KIAS
6170 lb (2800 kg) 124 KIAS
5730 lb (2600 kg) 120 KIAS
Page 3�
NORMAL PROCEDURES
The procedures listed in this section are taken directly from the actual Pilatus PC-12 Pilot’s Operating Handbook. Although we have designed the Flight1 Software Pilatus PC-12 for FSX to resemble and function as closely as possible the real PC-12, it is not designed as a training device. It’s possible that some checklist procedures listed may not be accomplished in this simulation.
This section provides the normal operating procedures for the aircraft. All of the procedures required by regulation as well as those procedures which have been determined as necessary for the operation of this aircraft are provided. Pilots must familiarize themselves with these procedures to become proficient in the normal operation of the aircraft.
General
Airspeeds for normal operations are listed below. Unless otherwise noted, all airspeeds are based on a maximum takeoff weight of 9,921 lb (4,500 kg) at sea level under ISA standard day conditions.
Airspeeds for Normal Operation
Takeoff:
Flaps 15º ......................................................................................................................79 KIAS Flaps 30º ......................................................................................................................73 KIAS
Maximum Climb:
Best Angle ..................................................................................................................110 KIAS
Best Rate Flaps 0º:
Up to 10000 Feet ........................................................................................................120 KIAS 15000 Feet .................................................................................................................115 KIAS 20000 Feet and Above .................................................................................................110 KIAS
Climb Speed with Flaps 0º and Pusher Ice Mode............................................................130 KIAS
Maximum Operating Maneuvering:
Speed (9921 lb / 4500 kg) ...........................................................................................158 KIAS
Maximum Flaps Extended: Flaps 15º ....................................................................................................................163 KIAS Flaps 40º ....................................................................................................................130 KIAS
Continued on Next Page
Page 35
[ ] Flight Control Lock ................................................. REMOVED AND PLACED IN STOWAGE POINT[ ] Parking Brake Handle..........................................................................SET/PUSH BRAKE PEDALS[ ] External Power Switch ........................................................................................................ OFF[ ] Battery 1 and 2 Switches .................................................................................................... OFF[ ] Generator 1 and 2 Switches ................................................................................................ OFF[ ] AV Bus 1 and 2 Switches ..................................................................................................... OFF[ ] Non-Essential Bus .............................................................................................................AUTO[ ] STBY BUS Switch .................................................................................................................ON[ ] TEST LAMP Switch ...........................................PUSH, CHECK OVERHEAD PANEL INDICATORS ON[ ] EXTERNAL LIGHTS Switches ............................................................................................... OFF[ ] FUEL PUMPS Switches ......................................................................................................AUTO[ ] IGNITION Switch..............................................................................................................AUTO[ ] DE-ICING Switches ............................................................................................................. OFF[ ] COOLING SYS Switch .......................................................................................................... OFF[ ] HEATING Switches ............................................................................................................. OFF[ ] Landing Gear Handle ...................................................................................................... DOWN[ ] ECS Switch ........................................................................................................................ OFF[ ] CABIN PRESS Switch ........................................................................................AUTO/GUARDED[ ] Cabin Pressure Controller ................................................. SET TO CRUISE ALTITUDE + 500 FEET[ ] Manual Override Lever ........................................................................................................ OFF[ ] Power Control Lever ............................................................................................. IDLE DETENT[ ] Condition Lever .............................................................................................CUT-OFF/FEATHER[ ] Flap Lever .............................................................................................................................0º[ ] Cockpit/Instrument/Cabin Light Switches ............................................................................. OFF
NORMAL PROCEDURES
Maximum Landing Gear:
Extension ....................................................................................................................177 KIAS Retraction ...................................................................................................................177 KIAS Extended ....................................................................................................................236 KIAS
Landing Approach Speed:
Flaps 0º ......................................................................................................................118 KIAS Flaps 15º ......................................................................................................................98 KIAS Flaps 30º ......................................................................................................................89 KIAS Flaps 40º ......................................................................................................................84 KIAS
Preflight Checklist
Continued on Next Page
Page 36
[ ] Preflight Inspections ................................................................................................. COMPLETE[ ] Battery 1 and 2 Switches ......................................................................................................ON[ ] Overhead Panel Voltmeter ................................................................. CHECK (23 VDC MINIMUM)[ ] Landing Gear 3 Greens ................................................................................................... CHECK[ ] Fuel Contents ................................................................CHECK EQUAL LEFT AND RIGHT LEVELS[ ] FUEL PUMP LH Switch ON and AUTO ....................................... CHECK FOR AUDIBLE OPERATION[ ] FUEL PUMP RH Switch ON and AUTO ....................................... CHECK FOR AUDIBLE OPERATION[ ] OXYGEN Lever .....................................................................................................................ON[ ] External Lights .................................................................................................... AS REQUIRED
[ ] Fuel Quantity ................................................................................................................. CHECK[ ] EIS System .......................................................................................................................TEST[ ] TEST FIRE Switch ...................................................PUSH (ENG FIRE AND F DETECT LIGHTS ON)[ ] TEST LAMP Switch .......................................PUSH (WARNING, CAUTION, ADVISORY LIGHTS ON)[ ] Propeller Area .................................................................................................................CLEAR[ ] STARTER Switch ......................................................................................PUSH FOR 2 SECONDS A) Oil Pressure ................................................................................................. CHECK RISING B) Ng .................................................................................... STABLE BETWEEN 9% AND 14%[ ] Condition Lever ...................................................................................................GROUND IDLE[ ] Starter Sequence ....................................................................................................COMPLETED[ ] Engine Instruments ........................................................................................................ CHECK[ ] Fuel Totalizer ..................................................................................................................RESET[ ] Generator 1 Switch ...................................................................... ON (CHECK CAWS GEN 1 OFF)[ ] Generator 2 Switch ...................................................................... ON (CHECK CAWS GEN 2 OFF)[ ] INVERTER BAT or GEN ....................................................CHECK FUNCTION/CHANGE SELECTION[ ] AV Bus 1 and 2 Switches .......................................................................................................ON[ ] STBY BUS Switch ............................................................................................................... OFF[ ] Radios/Avionics ................................................................................................... AS REQUIRED[ ] ESC Switch ......................................................................................................................AUTO[ ] Temperature Setting ............................................................................................ AS REQUIRED[ ] Cooling or Heating System ................................................................................... AS REQUIRED[ ] Inertial Separator .............................................................................................................OPEN
Before Starting Engine Checklist
Engine Starting Checklist
NORMAL PROCEDURES
Continued on Next Page
Page 3�
[ ] Takeoff Power Setting ............................................................................................CALCULATED
[ ] Fuel Quantity ................................................................................................................. CHECK
[ ] Engine Instruments ........................................................................................................ CHECK
[ ] Flight Instruments .......................................................................................................... CHECK
[ ] Trim ..............................................................................................................SET GREEN LINES
[ ] Flaps ..................................................................................................................................15º
[ ] Flight Controls ............................................................................................FREE AND CORRECT
[ ] CAWS Panel ........................................................................CHECK (NO WARNING RED LIGHTS)
[ ] Radios/Avionics ................................................................................................... AS REQUIRED
[ ] De-Ice Probes Switch ............................................................................................................ON
[ ] Windshield Heat .................................................................................................. AS REQUIRED
[ ] External Light Switches ........................................................................................ AS REQUIRED
[ ] Transponder .........................................................................................................ON ALTITUDE
[ ] Condition Lever ..................................................................................................... FLIGHT IDLE
[ ] DE-ICING Switches .............................................................................................. AS REQUIRED
[ ] AHRS 1/AHRS2.............................................................................................CHECK (NO FLAGS)[ ] Flaps Lever .........................................................................................................................15º[ ] Autopilot Test Button ................................................................................PRESS MOMENTARILY[ ] CAWS Panel ........................................................................CHECK (NO RED WARNING LIGHTS)[ ] DE-ICING PROBES Switch ...................................................PUSH TO ON AND CHECK CAWS AOA
DE-ICE, PITOT 1, PITOT 2, STATIC CAUTIONS OFF[ ] DE-ICING LH WSH Switch .............................. PUSH TO ON AND CHECK CAWS WSHLD HEAT OFF[ ] DE-ICING RH WSH Switch .............................. PUSH TO ON AND CHECK CAWS WSHLD HEAT OFF[ ] EXTERNAL LIGHTS Switches ................................................................................ AS REQUIRED[ ] Parking Brake Handle...................................................................................................RELEASE
NORMAL PROCEDURES
Before Taxiing Checklist
Taxiing Checklist
Before Takeoff Checklist
Continued on Next Page
[ ] Brakes ........................................................................................................................... CHECK[ ] Flight Instruments .......................................................................................................... CHECK
Page 3�
NORMAL PROCEDURES
Takeoff Checklist
Climb Checklist
Continued on Next Page
[ ] EHSI ..................................................................................................................... CHECK HDG
[ ] ESC Switch ........................................................................................................................ OFF
[ ] Power Control Lever ............................................................................................................SET
[ ] Engine Instruments
A) Torque ................................................................................................................MONITOR
B) ITT .....................................................................................................................MONITOR
C) Ng ......................................................................................................................MONITOR
D) Oil Temp/Pressure ...............................................................................................MONITOR
[ ] Rotate at Vr, Initial Climb at Vx or Vy .................................................................... AS REQUIRED
[ ] Brakes ................................................................................. PRESS TO STOP WHEEL ROTATION
After Lift-Off and Positive Rate of Climb:
[ ] Landing Gear Handle ............................................................................................................ UP
[ ] Flaps .......................................................................................................... 0º ABOVE 100 KIAS
[ ] Taxi Light ........................................................................................................................... OFF
[ ] External Lights .................................................................................................... AS REQUIRED
[ ] Yaw Damper ....................................................................................................... AS REQUIRED
[ ] Ice Protection System .......................................................................................... AS REQUIRED
[ ] Autopilot ............................................................................................................. AS REQUIRED
[ ] Power Control Lever ............................................................................................................SET
[ ] ECS Switch ......................................................................................................................AUTO
[ ] Engine Instruments
A) Torque ................................................................................................................MONITOR
B) ITT .....................................................................................................................MONITOR
C) Ng ......................................................................................................................MONITOR
D) Oil Temp/Pressure ...............................................................................................MONITOR
[ ] Temperature Setting ............................................................................................ AS REQUIRED
[ ] Inertial Separator ......................................................................................................... CLOSED
Page 3�
Cruise Checklist
Descent Checklist
Before Landing Checklist
Final Check Checklist
NORMAL PROCEDURES
Continued on Next Page
[ ] Altimeters ....................................................................................................SET 29.92 (1013.2)[ ] AHRS............................................................................................................................. CHECK[ ] Cabin Pressurization ...................................................................................................MONITOR[ ] Power Control Lever ............................................................................................................SET[ ] Engine Instruments ....................................................................................................MONITOR[ ] Ice Protection System .......................................................................................... AS REQUIRED
[ ] Ice Protection System .......................................................................................... AS REQUIRED[ ] Power Control Lever .......................................................................... SET TO DESIRED TORQUE[ ] Cabin Pressure Controller ..................................................SET TO FIELD ELEVATION + 500 FEET[ ] Windshield Heat .................................................................................................. AS REQUIRED
[ ] Landing Gear ............................................................................................................ 3 GREENS[ ] Flaps (Normal) ................................................................................ SET 40º (BELOW 130 KIAS)[ ] Speed ...............................................................................................................AOA CENTERED[ ] Pressurization ................................................................................................0 DIFF PRESSURE[ ] Autopilot .............................................................................................................. DISENGAGED[ ] Yaw Damper ........................................................................................................ DISENGAGED
[ ] Ice Protection System .......................................................................................... AS REQUIRED[ ] Altimeter ............................................................................................................................SET[ ] Fuel Quantity ................................................................................................................. CHECK[ ] Landing Gear .....................................................................................DOWN (BELOW 177 KIAS)[ ] Landing Lights .................................................................................................... AS REQUIRED[ ] External Lights .................................................................................................... AS REQUIRED[ ] Flaps (Normal) .....................................................................................SET 15º (MAX 163 KIAS)[ ] Speed ...............................................................................................................AOA CENTERED[ ] Passengers ..................................................................................................................... BRIEF[ ] Inertial Separator ...............................................ON (IF OPERATING ON UNPREPARED SURFACE)
Page �0
Landing
Landing
Shutdown
NORMAL PROCEDURES
[ ] Power Control Lever ............................................................................................. IDLE DETENT
[ ] Parking Brake ................................................................................................SET/PEDALS PUSH
[ ] ECS Switch ........................................................................................................................ OFF
[ ] External Light Switches ....................................................................................................... OFF
[ ] DE-ICING Switches ............................................................................................................. OFF
[ ] Cooling and Heating Systems .............................................................................................. OFF
[ ] STBY BUS Switch .................................................................................................................ON
[ ] AV BUS 1 and 2 Switches .................................................................................................... OFF
[ ] Generator 1 and 2 Switches ................................................................................................ OFF
[ ] Condition Lever .............................................................................................CUT-OFF/FEATHER
[ ] Lighting Switches ............................................................................................................... OFF
[ ] CAWS OIL QTY Warning ................................................................................................. CHECK
[ ] Battery 1 and 2 Switches .................................................................................................... OFF
[ ] STBY BUS Switch ............................................................................................................... OFF
When Runway Vacated:
[ ] Power Control Lever ............................................................................................ AS REQUIRED
[ ] Condition Lever ...................................................................................................GROUND IDLE
[ ] Flaps ................................................................................................................................... UP
[ ] External Lights .................................................................................................... AS REQUIRED
[ ] All De-Icing Switches .......................................................................................................... OFF
[ ] Transponder ......................................................................................................................STBY
[ ] Touchdown ...............................................................................................MAIN WHEELS FIRST
[ ] Flair .......................................................................... DO NOT FLARE WITH HIGH PITCH ANGLE
[ ] Power Control Lever .......................................................................................................... IDLE
[ ] Condition Lever ...................................................................................................GROUND IDLE
[ ] Braking ............................................................................................................... AS REQUIRED
Page ��
PERFORMANCE CHARTS
The performance charts listed in this section are taken directly from the actual PC-12 Pilot’s Operating Handbook. Although we have taken great pains to ensure that the Flight1 Software PC-12 for FSX flies as closely to the real thing as possible, in some cases performance of the sim aircraft may not match exactly the performance of the real aircraft due to programming limitations in Flight Simulator.
This section contains the required performance data for airplane operation. The performance information presented in this section is derived from actual flight test data corrected to standard day conditions and analytically expanded for the different parameters such as weight, altitude, temperature, etc.
General
Stall Speeds - Flight Idle Power
Continued on Next Page
Page �2
PERFORMANCE CHARTS
Takeoff Ground Roll
Continued on Next Page
Page �3
PERFORMANCE CHARTS
Maximum Power Cruise
Long Range Cruise
Continued on Next Page
Page ��
PERFORMANCE CHARTS
Cruise Climb Airspeed Schedule
Continued on Next Page
Page �5
Landing Ground Roll
PERFORMANCE CHARTS
Power-Off Glide Distance
Page �6
WEIGHT AND BALANCE
This section contains the information required to determine the Basic Empty Weight and Moment of the aircraft, and calculate aircraft loading for various flight operations. A sample loading form is provided.
To achieve the performance designed for the aircraft it must be flown with approved weight and center of gravity limits. It is the responsibility of the pilot in command to make sure that the aircraft does not exceed the maximum weight limits and is loaded within the center of gravity range before takeoff.
General
Example Loading Form
1. Basic Empty Weight
2. Combi Interior Conversion
3. Pilot
4. Copilot (Right Seat Passenger)
5. Passenger 1
6. Passenger 2
7. Passenger 3
8. Passenger 4
9. Passenger 5
10. Passenger 6
11. Passenger 7
12. Passenger 8
13. Passenger 9
14. Optional Wardrobe
15. LH Cabinet
16. RH Cabinet
17. a. Rear Baggage (Net at Frame 32)
b. Rear Baggage (Net at Frame 34)
18. Cargo
19. Zero Fuel Weight MZFW 9039 lb (4100kg) (Sum of 1-18)
20. Fuel
21. Ramp Weight MRW 9965 lb (4520 kg) (Sum of 19+20)
22. Less Fuel for Ground Operations
23. Add Moment Due to Gear Retraction
24. Takeoff Weight MTOW 9921 lb (4500 kg) (Sum of 21-22+23)
5613
N/A
170
170
170
170
170
170
170
170
170
170
170
215
7698
1650
9348
40
-
9308
225.16 (5.719)
N/A
160.27 (4.071)
160.27 (4.071)
215.00 (5.461)
212.03 (5.386)
248.00 (6.299)
245.03 (6.224)
281.00 (7.137)
278.05 (7.062)
314.00 (7.976)
311.03 (7.900)
344.03 (8.738)
191.00 (4.851)
212.10 (5.387)
211.19 (5.364)
361.00 (9.170)
370.87 (9.420)
229.49
-
229.92
-
-
229.97
1263823
N/A
27246
27246
36550
36045
42160
41655
47770
47268
53380
52875
58485
79765
1814268
382790
2197058
9369
538(6.2)
2188227
ITEM WEIGHT LB
ARM AFT OF DATUM In (m)
MOMENTLB-IN
Continued on Next Page
Page ��
WEIGHT AND BALANCE
Blank Loading Form
1. Basic Empty Weight
2. Combi Interior Conversion
3. Pilot
4. Copilot (Right Seat Passenger)
5. Passenger 1
6. Passenger 2
7. Passenger 3
8. Passenger 4
9. Passenger 5
10. Passenger 6
11. Passenger 7
12. Passenger 8
13. Passenger 9
14. Optional Wardrobe
15. LH Cabinet
16. RH Cabinet
17. a. Rear Baggage (Net at Frame 32)
b. Rear Baggage (Net at Frame 34)
18. Cargo
19. Zero Fuel Weight MZFW 9039 lb (4100kg) (Sum of 1-18)
20. Fuel
21. Ramp Weight MRW 9965 lb (4520 kg) (Sum of 19+20)
22. Less Fuel for Ground Operations
23. Add Moment Due to Gear Retraction
24. Takeoff Weight MTOW 9921 lb (4500 kg) (Sum of 21-22+23)
-
160.27 (4.071)
160.27 (4.071)
191.00 (4.851)
212.10 (5.387)
211.19 (5.364)
361.00 (9.170)
370.87 (9.420)
-
-
- 538(6.2)
ITEM WEIGHT LB (kg)
ARM AFT OF DATUM In (m)
MOMENTLB-IN (kg-m)
Please note that not all ITEMs listed in this blank loading form can be adjusted from within Flight Simulator or otherwise.
Continued on Next Page
Page ��
C.G. Envelope
WEIGHT AND BALANCE
THIS SPACE INTENTIONALLY LEFT BLANK
Page ��
© 200� Flight� Software. All Rights Reserved.
www.flight1.com Version �.0D
Top Related