7/29/2019 MIT2_094S11_bajoria
1/24
MASSACHUSETTS INSTITUTE OF TECHNOLOGY
Analyzing wind flow around the square plate usingADINA
2.094 - Project
Ankur Bajoria
May 1, 2008
7/29/2019 MIT2_094S11_bajoria
2/24
MIT 2008: 2.094 Project
Acknowledgement
I would like to thank ADINA R & D, Inc for the full version of the software. I am grateful to
Professor K.J. Bathe who has made the difficult topic of finite element easy to understand in his
course 2.094. Special thanks to Dr. Shanhong Ji who provided valuable guidance to improve the
model and complete the project. Equally important are the inputs from Renard Gamaliel and Ali
Lame. Their comments have contributed to this projects improvement.
2
7/29/2019 MIT2_094S11_bajoria
3/24
MIT 2008: 2.094 Project
Table of Contents
Acknowledgement ......................................................................................................................2
Table of Contents........................................................................................................................3
List of Figures.............................................................................................................................4
1. Introduction .........................................................................................................................6
2. Modeling and governing parameters in ADINA ...................................................................6
3. Results ...............................................................................................................................11
4. Conclusion .........................................................................................................................23
5. References .........................................................................................................................23
3
7/29/2019 MIT2_094S11_bajoria
4/24
MIT 2008: 2.094 Project
List of Figures
Figure 1: model outline ...............................................................................................................7
Figure 2: model in ADINA..........................................................................................................8
Figure 3: boundary conditions and loads applied to model...........................................................8
Figure 4: model mesh ..................................................................................................................9
Figure 5-a: Cp (i) and face .........................................................................................................11
Figure 5-b: Cp plot for three face (viscosity=0.01) .....................................................................11
Figure 6-a: Cp plot simulation by S. Murakami [1] ....................................................................12
Figure 6-b: Cp plot simulation and experimental by S. Murakami [1] ........................................12
Figure 7: velocity magnitude.....................................................................................................13
Figure 8: y-velocity ...................................................................................................................13
Figure 9: z-velocity ...................................................................................................................14
Figure 10: Omega-yz.................................................................................................................14
Figure 11: Nodal pressure .........................................................................................................14
Figure 12: Turbulence kinetic energy ........................................................................................15
Figure 13: Cell Reynolds number ..............................................................................................15
Figure 14: Cp plot for three face (viscosity=0.001)....................................................................16
Figure 15: velocity magnitude ...................................................................................................16
Figure 16: y-velocity .................................................................................................................17
Figure 17: z-velocity .................................................................................................................17
Figure 18: Omega-yz.................................................................................................................17
Figure 19: Nodal pressure .........................................................................................................18
4
7/29/2019 MIT2_094S11_bajoria
5/24
MIT 2008: 2.094 Project
Figure 20: Turbulence kinetic energy ........................................................................................18
Figure 21: Cell Reynolds number ..............................................................................................19
Figure 22: Cp plot for three face (viscosity=0.0001)..................................................................20
Figure 23: velocity magnitude ...................................................................................................20
Figure 24: y-velocity .................................................................................................................21
Figure 25: z-velocity .................................................................................................................21
Figure 26: Omega-yz.................................................................................................................21
Figure 27: Nodal pressure .........................................................................................................22
Figure 28: Turbulence kinetic energy ........................................................................................22
Figure 29: Cell Reynolds number ..............................................................................................22
5
7/29/2019 MIT2_094S11_bajoria
6/24
7/29/2019 MIT2_094S11_bajoria
7/24
7/29/2019 MIT2_094S11_bajoria
8/24
MIT 2008: 2.094 Project
the model outline. The special boundary condition of slip is applied to the two sides of the flow
boundary. This special boundary condition is different from the normal boundary condition used
in ADINA in the sense that these are discretized within boundary elements. The loads applied for
the turbulence model is velocity and turbulence load at the inlet boundary. Here a velocity of v=1
and turbulence=1 is applied.
Figure 2: model in ADINA
Figure 3: boundary conditions and loads applied to model
8
7/29/2019 MIT2_094S11_bajoria
9/24
MIT 2008: 2.094 Project
The turbulence intensity of 0.025 and dissipation length of 1 is used. The prescribed value of the
turbulence and the kinetic energy at the inlet boundary are calculated from the following
equations.
3K= ( iv )
2
(1.2)2
3
= K2
(0.3L )(1.3)
where , and are velocity scale, length scale and turbulence intensity respectively. The zeroturbulence flux is implicitly assumed at the boundary where no turbulence is explicitly specified
Figure 4: model mesh
The figure 4 shows the mesh used for the analysis. Finer mesh is used near the plate boundary.
All the surfaces have the ratio 1 for the largest to smallest element. 4 node quadrilateral elements
are used in which velocity is computed at all 4 nodes and pressure computed at the centre. The
default values for the K- turbulence material model for the various parameters are used. Thesevalues are given below:
9
7/29/2019 MIT2_094S11_bajoria
10/24
MIT 2008: 2.094 Project
C=0.09, C1=1.42, C2=1.92,C3=0.8, k=1, =1.3,
=0.9 ,=70, 0=0.4
The automatic time stepping function (ATS) with 10 sub-divisions is used for the steady-state
incompressible flow analysis. The parameters that have been explained above remains same for
all the models. Apart from the above, the parameters that vary in each of the model are now
discussed.
In Model 1, Viscosity=0.01, default time function which is full loads applied from the start of
analysis, default time step which is full loads at first step and number of iteration in newton
method are 15 is used.
In Model 2, Viscosity=0.001, a linear time function which is full loads applied linearly from zero
to full load in time one, smaller time step which is full loads applied to the model in two steps of
magnitude 0.1 & 0.9 and number of iteration in newton method are 100 is used.
In Model 3, Viscosity=0.0001, a linear time function which is full loads applied linearly from
zero to full load in time one, smaller time step which is full loads applied to the model in three
steps of magnitude 0.1, 0.3 & 0.6 and number of iteration in newton method are 100 is used.
These changes are required to make the set of equations stable under high Reynolds number
which is increased due to the decrease in the viscosity of the fluid. The solution doesnt converge
if full loads are applied in one step and hence smaller time step is required to reach convergence.
10
http:///reader/full/C1=1.42http:///reader/full/C2=1.92http:///reader/full/Viscosity=0.01http:///reader/full/Viscosity=0.01http:///reader/full/Viscosity=0.01http:///reader/full/C2=1.92http:///reader/full/C1=1.427/29/2019 MIT2_094S11_bajoria
11/24
MIT 2008: 2.094 Project
3. Results
To verify the model and the boundary conditions used the results are compared to the
experimental and simulation data that has been published for the flow around the square plate.
For the purpose of comparison the graphs of pressure coefficient (Cp) for the different face of the
plate have been plotted. The figure 5-a shows the face and corresponding C p (i), i=1, 2, 3. The
figure 5-b shows the graph of Cp for different face. The figure 6-a shows the corresponding
graph for experimental and 6-b simulation data [1].
Cp
Cp2
Cp
Figure 5-a: Cp (i) and face
Figure 5-b: Cp plot for three face (viscosity=0.01)
11
7/29/2019 MIT2_094S11_bajoria
12/24
MIT 2008: 2.094 Project
Figure 6-a: Cp plot simulation by S. Murakami [1]
Figure 6-b: Cp plot simulation and experimental by S. Murakami [1]
From the above comparison we see the calculated Cp from the model is in agreement with the
experimental results. The various plots for the first model are shown below:
12
Courtesy of Elsevier, Inc.,http://www.sciencedirect.com. Used with permission.
http://www.sciencedirect.com/http://www.sciencedirect.com/http://www.sciencedirect.com/http://www.sciencedirect.com/7/29/2019 MIT2_094S11_bajoria
13/24
MIT 2008: 2.094 Project
Figure 7: velocity magnitude
Figure 8: y-velocity
The velocity distribution due to the square in the flow field is shown by figure 7, 8, 9. Zero and
negative velocity is developed behind the square, which causes the circulation. From the figure
10, the formation of vortices around the corner of the square plate is indicated.
13
7/29/2019 MIT2_094S11_bajoria
14/24
MIT 2008: 2.094 Project
Figure 9: z-velocity
Figure 10: Omega-yz
Figure 11: Nodal pressure
14
7/29/2019 MIT2_094S11_bajoria
15/24
7/29/2019 MIT2_094S11_bajoria
16/24
MIT 2008: 2.094 Project
Plots for model 2(viscosity=0.001) are now shown:
From the figure 15, the increase in the magnitude of velocity as compared to the same plot at
lower Reynolds number can be noticed. Also other plots show the increase in the intensity of
parameters such as kinetic energy, turbulence and omega-yz etc.
Figure 14: Cp plot for three face (viscosity=0.001)
Figure 15: velocity magnitude
16
7/29/2019 MIT2_094S11_bajoria
17/24
MIT 2008: 2.094 Project
Figure 16: y-velocity
Figure 17: z-velocity
Figure 18: Omega-yz
17
7/29/2019 MIT2_094S11_bajoria
18/24
MIT 2008: 2.094 Project
From figure 18, vortices formation at the edge of the plate is shown. Due to the increase in the
Reynolds number of the flow effect of these vortices is increased in the downstream of the flow.
The nodal pressure is increased but only by small amount which would be generally negligible
when a factor of safety is used in the design of the structure. Figure 20, shows the highly
turbulent region behind the plate which indicates the formation of eddies in the leeward region of
flow.
Figure 19: Nodal pressure
Figure 20: Turbulence kinetic energy
18
7/29/2019 MIT2_094S11_bajoria
19/24
MIT 2008: 2.094 Project
Figure 21: Cell Reynolds number
19
7/29/2019 MIT2_094S11_bajoria
20/24
MIT 2008: 2.094 Project
Plot for model 3 (viscosity=0.0001)
Figure 22: Cp plot for three face (viscosity=0.0001)
Figure 23: velocity magnitude
20
7/29/2019 MIT2_094S11_bajoria
21/24
MIT 2008: 2.094 Project
Figure 24: y-velocity
Figure 25: z-velocity
Figure 26: Omega-yz
21
7/29/2019 MIT2_094S11_bajoria
22/24
MIT 2008: 2.094 Project
Figure 27: Nodal pressure
Figure 28: Turbulence kinetic energy
Figure 29: Cell Reynolds number
22
7/29/2019 MIT2_094S11_bajoria
23/24
MIT 2008: 2.094 Project
4. Conclusion
The current status of the available turbulence models in the finite element software like ADINA
makes it possible to evaluate the flow past bluff bodies. This analysis can be then applied during
the design phase to improve the aerodynamics of the structure and reduce the forces. Also the
effect of circulation and vortices may be studied and effectively dealt with. With the
advancement in the computational methods application of finite element in the field of
computational wind engineering will surely increase.
5. References
1. S. Murakami, Computational wind engineering, Journal of Wind Engineering and
Industrial Aerodynamic 36 (1990), pp. 517538.
2. S. Murakami, Comparison of various turbulence models applied to a bluff body, Journal
of Wind Engineering and Industrial Aerodynamic 46/47 (1993), pp. 2136.
3. S. Murakami and A. Mochida, On turbulent vortex shedding flow past 2D square cylinder
predicted by CFD, Journal of Wind Engineering and Industrial Aerodynamic 54/55
(1995), pp. 191211
4. Klaus-Jrgen Bathe, Finite Element Procedures, Prentice Hall, 1996
23
7/29/2019 MIT2_094S11_bajoria
24/24
MIT OpenCourseWarehttp://ocw.mit.edu
2.094 Finite Element Analysis of Solids and Fluids
Spring 2011
For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms.
http://ocw.mit.edu/http://ocw.mit.edu/http://ocw.mit.edu/termshttp://ocw.mit.edu/termshttp://ocw.mit.edu/termshttp://ocw.mit.edu/