Microcontroller Based Wireless
Camera Security System
John Saylor
Computer Electronic Networking
2
OUTLINE Motivation Introduction Problems Statement Proposed solution Results Conclusions Future work Questions & Comments
3
MOTIVATION
Being home alone in the mountains of eastern KY can be scary at times.
With crazy moon shiners, pot growers and all the black bear, elks, black panthers and bob cats. And of course the bear dog himself …
Can’t go outside when these wild creatures are around.
Need a camera to see what is lurking about and see if it is safe to go outside.
This inspired me to build a wireless security camera system to see what is happening.
4
INTRODUCTION – Microcontroller
I used a basic stamp Microcontroller to control inputs and outputs. My inputs were two toggle switches and a photo resistor. These
controlled when the outputs turned on. The outputs are 4 lines tied to a stepper motor The initial outputs were 4 LEDs which were used for diagnosing
problems and testing the output lines.
5
INTRODUCTION – Stepper motor
The stepper motor I found in the lab came from a printer. A stepper motor can be used for precise control of an
object and has large amounts of torque. The separate outputs would allow me to control the
direction and how many turns or steps the motor would take.
6
INTRODUCTION – Stepper motor
Stamp Code
7
INTRODUCTION – Wireless Camera
I bought a wireless 2.4GHZ camera to see what was going on outside my house.
The camera is only about the size of a quarter and runs on a 9 volt battery.
The signal is broadcasted to a receiver.
8
INTRODUCTION – Webcam XP
I used Webcam XP in order to see what was happening at my house if I were not home.
Webcam XP allows you to broadcast your webcam or other media device over the internet.
9
PROBLEM STATEMENT
Problems Encountered during the implementation stage of my project.
Conflicting IP addresses Changing broadcast channel of wireless router Setting up Webcam XP server Finding compatible software
10
PROPOSED SOLUTION – IP’s Conflicting
Solving these issues I used the following method.
Testing and Troubleshooting I set up static IP address on my host computer. Also set static IP address on my laptop. Turned off DHCP from my router.
11
PROPOSED SOLUTION – Broadcast Channel
I logged into my router and changed my broadcast signal from channel 11 to 3.
The broadcast signal of the wireless receiver was using channel 11 and I could change it.
12
PROPOSED SOLUTION – Webcam XP
In order to use Webcam XP I had to set up routing tables. Logged into my router and found routing tables and added
Webcam XP and the port forwarding address which was port 8080 This allowed the port to be open for broadcasting the webcam
server.
13
PROPOSED SOLUTION – Compatible Software
Software and Hardware I tested many types of software. Freeware and shareware
versions of many types. None were compatible or worked like they said they would
after testing almost 15 different types. I finally found a shareware program called Webcam XP
and it worked perfect.
14
RESULTS
The four key results for my project were,
1. Microcontroller board
2. Stepper motor control
3. Wireless camera
4. Webcam server
15
RESULTS
Microcontroller board
Photo Resistor
Transistor
Reset Output LED
Power and output signal to stepper motor
16
RESULTS
Stepper motor
17
RESULTS
Wireless camera
18
RESULTS
Camera
movement
with
stepper
19
RESULTS
Server
Program
WebCam XP
20
RESULTS
Viewing a webcam
remotely from laptop
on wireless
connection
21
CONCLUSIONS
Learned how to setup, program and run a microcontroller. Learned how stepper motors work and their uses. Learned how NOT to set up a wireless camera, and Webcam XP
using all default settings and having to struggle for many hours trying to figure out what is wrong.
22
CONCLUSIONS
Learning experience while working on the capstone project has been challenging and frustrating at times.
However the ability to accomplish this project has been a great college experience.
I have learned that spending your time wisely is a major part of a senior project.
23
FUTURE WORK
The possible extensions for this project is only limited by the persons imagination.
This is because the microcontroller can be used to do many applications.
Also the wireless camera can be used to watch over many types of situations.
24
FUTURE WORK
At this time does anyone have any
Questions?
Thank You
Top Related