7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
1/39
Mahmmoud A. Mahdi
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
2/39
The Routing Information Protocol The important differences between RIPv1 and RIPv2:
The primary, or most important, difference between versions 1and 2 of RIP is that: RIPv2 supports variable-length subnet masking (VLSM). VLSM helps
preserve IP address space by enabling networks to be subdivided intosmaller blocks based on need.
RIPv2 supports simple (that is, plain text) username/passwordauthentication which is handy to prevent unwanted changes from cluttering your routing
tables.
RIPv2 routers add the ability to receive triggered updates. When you know that your network topology is changing. This trigger
forces all the RIP routers you own to assimilate the changes immediately.
Triggered updates are also useful because routers that detect a link orrouter failure can update their routing tables and announce the change,making their neighbors aware of it sooner rather than later.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
3/39
You can use the Routing And Remote Accesssnap-in to set up two kinds of filters thatscreen out some types of RIP updates:
Route filters allow you to pick and choose thenetworks that you want to admit knowing aboutand for which you want to acceptannouncements.
Peer filters give you control over theneighboring routers to which your router willlisten.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
4/39
RIP has two operation modes: Periodic update mode, a RIP router sends out its list
of known routes at periodic intervals (which you
define). Autostatic update mode, the RRAS router
broadcasts the contents of its routing table onlywhen a remote router asks for it. One drawback to RIP in either version is that it causes the
router to send its entire routing table with every update.This can generate a large amount of traffic and makes RIPinappropriate for many of todays networks.
Another routing protocol, Open Shortest Path First, solvesthis problem by sending updates for only routes that havechanged.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
5/39
Internal routing:
Refers to routing that occurs within your
internetwork. By contrast, border routing iswhat happens when packets leave your
internetwork and go to another router
someplace else.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
6/39
Filters are usually used to block out
undesirable traffic.
In general, the idea is to keep out packetsthat your machines doesnt need to see.
You can construct filters that allow traffic
into or deny traffic out of your network
based on rules that specify source and
destination addresses and ports.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
7/39
The basic idea behind packet filtering issimple:
1. You specify filter rules.
2. Incoming packets are measured against thoserules.
There are two types of filter rule:
Accept all packets except those prohibited by arule.
Drop all packets except those permitted by arule.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
8/39
The following are some examples of filters:
Block all packets to a web server except those
on TCP ports 80 and 443. Block all outgoing packets on the ports used by
the MSN and AOL instant messaging tools.
Filters on a PPTP or L2TP server can screen out
everything except VPN traffic.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
9/39
You create and remove filters by using theInput Packet Filters and Output Packet Filtersbuttons on the General tab of the Local Area
Network Properties dialog box. The mechanics of working with incoming and
outbound filters are identical; just rememberthe following guidelines:
You create inbound filters to screen traffic coming tothe interface.
You create outbound filters to screen traffic goingback out through that interface.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
10/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
11/39
This dialog box has the following six parts: Receive All Packets Except Those That Meet The Criteria Below
excludes the packets you specify and accepts everything else. This option is inactive until you create a filter rule.
Drop All Packets Except Those That Meet The Criteria Belowaccepts only those packets you specify and excludes everything else. This option is inactive until you create a filter rule.
The Filters list, which is initially empty, shows you which filters aredefined on this interface. Each entry in the list shows the following:
Source address and mask
Destination address and mask
Protocol, port, and traffic type specified in the rule
The New, Edit, and Delete buttons allow you to add, edit, andremove filters.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
12/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
13/39
To create a filter that blocks packets by their origin or sourceaddress, check the Source Network box, and supply the IPaddress and subnet mask for the source you want to block.
To create a filter that blocks packets according to theirdestination address, check the Destination Network box, and fillin the appropriate address and subnet mask.
To filter by protocol, choose the protocol you want to block: Any, which blocks everything
TCP
TCP (Established)
IP UDP
ICMP
Other, with a fill-in field for a protocol number
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
14/39
Packet filters provide a useful security
mechanism for blocking unwanted traffic on
particular machines. Its a good idea to use packet filters to keep non-VPN
traffic out of your VPN servers.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
15/39
You need at least two filters to adequately screenout non-PPTP traffic:
The first filter allows traffic with a protocol ID of 47
the Generic Routing Encapsulation (GRE) protocoltopass to the destination address of the PPTP interface.
The second filter allows inbound traffic bound for TCPport 1723 (the PPTP port) to come to the PPTPinterface.
You can add a third filter if the PPTP server also worksas a PPTP client; in that case, the third filter needs theinterfaces destination address, a protocol type of TCP(established), and a source port of 1723.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
16/39
1. Open the Routing And Remote Access snap-in by selecting Start\
Administrative Tools \Routing And Remote Access. Expand the server and
IPv4 nodes to expose the General node of the server on which youre working.
Select the General node.
2. Right-click the Local Area Connection interface, and choose Properties.
3. In the General tab of the interfaces Properties dialog box, click the Inbound
Filters button. The Inbound Filters dialog box appears.
4. Click the New button, and the Add IP Filter dialog box appears.
5. Fill out the Add IP Filter dialog box as follows:
Check the Destination Network check box.
Fill in the destination IP address field with the IP address of the remote VPN interface. (Forthis exercise, we entered 192.168.1.254. You can use the same.)
Enter a destination subnet mask of 255.255.255.255.
Select a protocol type of TCP, and then specify a source port of 0 and a destination port of
1723.
Click the OK button.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
17/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
18/39
6. The Inbound Filters dialog box reappears, listingthe new filter you created in step 5.
Add another new filter using the same IP address and
subnet mask, but this time specify Other in the Protocolfield and fill in a protocol number of 47.
When youre done, click the OK button to return to theInbound Filters dialog box.
7. In the Inbound Filters dialog box,
Click the Drop All Packets Except Those That Meet TheCriteria Below radio button
And click the OK button.
8. Close the interfaces Properties dialog box.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
19/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
20/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
21/39
Four filters are requiredtwo input filters andtwo output filters: Two input filters with a destination of the VPN
interface address and a netmask of255.255.255.255, filtering UDP: One with a source and destination port of 500
The second with a source and destination port of 1701
Two output filters with a source of the VPN
interface address and a netmask of255.255.255.255, filtering UDP: One with a source and destination port of 500
The second with a source and destination port of 1701
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
22/39
1. Open the Routing And Remote Access snap-in by selecting Start \Administrative Tools \Routing And Remote Access.
2. Select the server whose status you want to monitor in the left pane of theMMC.
3. Select the Network Interfaces node. Notice that the right pane of the MMC now lists all known interfaces along with their
status and connection state.4. Select the General node beneath IPv4.
Notice that the right pane of the MMC updates to show the IP interfaces, their IPaddresses, their administrative and operational states, and whether IP filtering isenabled on each interface.
5. Right-click the General node, and choose the Show TCP/IP Informationcommand.
Check the number of IP routes shown.6. Right-click the Static Routes node, and choose the Show IP Routing Table
command. Note that the number of routes listed corresponds to the route count in the TCP/IP
Information window and that some of the routes listed are automatically generated.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
23/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
24/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
25/39
IP multicasting works by sending to a singleIP address a packet that is read by manyhosts.
Multicasting uses a special range of IPaddresses, called the Class D address space, thatis reserved exclusively for multicasting.
Internet Group Management Protocol(IGMP) is used to exchange multicast groupmembership information betweenmulticast capable routers.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
26/39
You can configure RRAS in two modes: IGMP router mode
Listens for IGMP membership report packets and tracksgroup membership.
Must be attached to any interfaces that connect tomulticast configured hosts.
IGMP proxy mode essentially acts like a multicast host, except that it forwards
IGMP membership report packets to an IGMP router.
This provides a list of multicast-enabled hosts to anupstream router that normally wouldnt be aware of thehosts.
Typically, it is used on single-router networks connected tothe Internet.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
27/39
IP-in-IP interfaces (or IP-in-IP tunnels)
You may need to send multicast traffic across
non-multicast-compatible routers. An IP-in-IP interface actually encapsulates
packets with an additional IP header.
You create and manage IP-in-IP interfaces in
RRAS the same way you configure otherinterfaces.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
28/39
Lesson 1
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
29/39
What Are Static and Dynamic Routing?
How the IP Protocol Selects a Route
Demonstration: Viewing a Routing Table Troubleshooting Routing
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
30/39
Statically configured routers:
Do not automatically discover the IDs of remotenetworks.
Do not exchange information with other routers. Are not fault tolerant.
Dynamically configured routers:
Discover the IDs of remote networks automatically.
Use a routing protocol to exchange information withother routers.
Can be fault tolerant.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
31/39
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
32/39
Lesson 2
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
33/39
RRAS Routing Roles
Routing Protocols
Configuration Options for an Interface Information Available for an Interface
Demonstration: Configuring RRAS as a LAN
Router
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
34/39
Routing roles include:
Routing role Description
LAN router Can route IPv4 and IPv6 packets between network
segments
Demand-dial Automatically create a connection to a remote location
by using dial-up networking or a VPN connection
NAT Perform NAT and allow computers to access the
internet by sharing a single internet addressable IPv4
address.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
35/39
Routing protocols include:
Routing Protocol Description
DHCP Relay Agent Allows a RRAS server to relay DHCP requests to a DHCPserver on a remote network
IGMP Router
Proxy
Allows a RRAS server to act as an IGMP router or proxy
for multicast traffic
NAT Allows a RRAS server to act as a NAT router to share a
single IPv4 address.RIP Version 2 for
Internet Protocol
Allows a RRAS router to perform dynamic routing with
other RIP routers.
DHCPv6 Relay
Agent
Allows a RRAS server to relay DHCP request to a DHCPv6
server on a remote network.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
36/39
Interface configuration options include:
Configuration Option Description
IP Router Manager Enables or disables TCP/IP for the interface.Router Discovery
Advertisements
Clients use router discovery advertisements to
dynamically discover default gateways.
Inbound/Outbound
filters
Filters similar to Windows Firewall.
Fragmentation checking Specifies whether filtering is performed on packetfragments.
Multicast boundaries Configures time to live for multicast traffic.
Multicast heartbeat
detection
Used to confirm that multicast infrastructure is
functioning properly.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
37/39
Available interface information includes:
Interface information Description
TCP/IP Information Statistics such as number of packets sent and
received.
Address Translations Translations from IP address to physical address.
IP Addresses IP addresses that are bound to this computer.
IP Routing Table Host and network routes in the routing table of this
computerTCP connections Active connection and listening TCP ports.
UDP listener ports A list of UDP ports listening to accept UDP packets.
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
38/39
Tool Use for Where to find it
Routing and Remote
Access
Configuring Routing and
Remote Access as a
router, VPN server, dial-
up server, or RADIUS
client.
Administrative Tools
Computer Management.
Route Views and modifies the
routing table.
Command prompt
Ping Verifying host availability
and reachability
Command prompt
Tracert Use to verify routerstatus on a network path
Command prompt
Pathping Use to verify router
status on a network path
Command prompt
Group Policy
Management Console
Edit group policy objects
Create QoS policies
Administrative Tools
7/29/2019 Lesson 7: Configuring IP Routing (Part 2)
39/39
Contact Me: [email protected]
Top Related