Download - INS TALLATION GUIDE SP / FIXED HOUSING | …...Aline the module with the driver bracket. Step 1-3 : Rotate one sixth of a circle. Step 1-1 : Locate the driver to the driver bracket

INSTALLATION GUIDE SP / FIXED HOUSING | ACROBAT

T-BARROUND (DOWNLIGHT) SHOWN.　 FOLLOW SAME STEPS FOR SQUARE WOOD

STEP 1 - FRAME INSTALL / HORIZONTAL ADJUSTMENT SPREAD HANGER BARS TO APPROPRIATE DISTANCE. FASTEN WITH HARDWARE (BY OTHERS) TO PREVENT VERTICAL MOVEMENT OF FIXTURE.

USE THE SREWDRIVER TO TIGHTEN THE SCREW.

READ AND FOLLOW ALL SAFETY INSTRUCTION! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.

Never connect components under loadDo not touch the yellow surface of the LED as it maydamage the light engine

WARNING: RISK OF ELECTRIC SHOCK

Before installation, servicing, or peforming routinemaintenace disconnect power by turning o� the circuitbreakers both to the outlet box and to its associatedwall switchInstallation and service of luminaires should beperformed by a qualified licensed electrician in accordance with all local and National Electical CodesDO NOT install damaged productVerify that supply voltage is correct by comparing it with the luminaire label informationAll wiring connections should be capped with ULapproved recognized wire connectors

WARNING: RISK OF INJURY

Allow luminaire to cool before servicing andperforming maintenaceFollow all manufacturer’s warnings and restrictionsfor: driver type, mounting locations, replacement andrecyclingWear safety glasses and gloves when installing,maintaining or servicingAvoid direct eye exposure to the light source while itis on

Keep combustible material away from luminaireDo not install insulation within 3” (76mm) of any partof the luminaire or in a way that may entrap heat

WARNING: RISK OF FIRE

WARNING: RISK OF PRODUCT DAMAGE

1 INCH:(67 x 67mm)

2 in852 x8

5

2 INCH:(85 x 85mm)

3 in833 x8

3

3 INCH:(112 x 112mm)

4 in834 x8

3

4 INCH:(138 x 138mm)

5 in835 x8

3

1 INCH: 2 in (67mm)85

2 INCH:3 INCH:4 INCH: 5 in (138mm)

3 in (85mm)83

4 in (112mm)83

83


STEP 2A - VERTICAL ADJUSTMENT

DOUBLE SIDE ADJUSTMENT / OUTSIDE

Loose the wing nuts to adjust the height of the housing, then tighten.

STEP 3A - CEILING CUTOUTFOR TRIMLESS SEE 3B.

STEP 3B - MUD RING (TRIMLESS ONLY)

ATTACH MUD RING TO CEILING WITH SCREWS.

COVER MUD RING WITH ATHIN LAYER OF FINISH PLASTER

STEP 2B - VERTICAL ADJUSTMENT

DOUBLE SIDE ADJUSTMENT / INSIDE

Wings nuts can also be acesssed on the inside of the housing for making fixture height adjustment.


INSTALLATION GUIDE SHALLOW MODULE 1” & 2” | ACROBAT

STEP 1 - COMBINE THE DRIVER AND MODULE WITH DRIVER BRACKET

WARNING: DO NOT USE AS A HANGING DEVICE. DOING SO MAY RESULT IN DAMAGE OR INJURY

CLICK!!

Step 1-2 :Aline the module withthe driver bracket.

Step 1-3 :Rotate one sixth of a circle.

Step 1-1 :Locate the driver to the driver bracket and use the screwdriver to tighten the screws.

STEP 2 - MAKE ELECTRICAL CONNECTION AND INSERT THE DRIVER BRACKET


Step 3-2A :Aline the module withthe twist lock bracket.

Step 3-2B :Twist and lock themodule clockwise.

Step 3-2C :Tighten the screwsto secure the module. (3A)

3A

Step 3-2 :Twist and lock themodule clockwise.

STEP 3 - INSERT THE DRIVER BRACKET ASSEMBLY

Step 3-1 :Slide and insert the driverbracket assembly.


STEP 4 - INSTALL THE LENS

Step 4-2 :Twist and lock the lens.

Step 4-1 :Locate the lens into theoptic bracket.

Step 3-3 :Use the screwdriver to tightenthe driver bracket assembly.


STEP 5 - INSTALL THE FLANGE AND REFLECTOR

Step 5-1 :Push up the flange into the collar.

Step 5-2 :Push up the reflector into the flange.