© Ricardo plc 2002 MARAD 2002
Humphrey NivenManager Large Engine Technology
Ricardo
Humphrey NivenManager Large Engine Technology
Ricardo
© Ricardo plc 2002 MARAD 2002 3
� Marine Emissions Legislation� Medium Speed Engines� Slow Speed Engines� Energy Savings� Alternative Fuels� Conclusions and Recommendations
© Ricardo plc 2002 MARAD 2002 4
Maritime Organisation(IMO)
Maritime Organisation(IMO)
� Once Annex VI is ratified, all diesel engines >130 Kw in ships built forinternational shipping operation after Jan 2000 must comply
� Fuel to ISO 8217 Grade DMA, DMB or DMC. Steady state testing.Ambient 25°C, Seawater 25°C
Marpol Annex VI NOx Limits
© Ricardo plc 2002 MARAD 2002 5
Possible future IMO NOx Regulation Reduction
0
2
4
6
8
10
12
14
16
18
0 500 1000 1500 2000 2500
Engine Speed (rpm)
NOx
(g/k
Wh)
IMO Emissions Limits
2nd Stage ?
3rd Stage? (Possibly +CO2)
Final Stage ? (Possibly +CO2 +PM +??)
DNV "CLEAN DESIGN" Certification
© Ricardo plc 2002 MARAD 2002 6
� Sulphur in HFO capped at 4.5%
� In SOx control area (SECA) fuel sulphur limited to1.5% or with secondary control devices <6.0 g/Kwhemissions
© Ricardo plc 2002 MARAD 2002 7
� California, Scandinavia and Japan have decided thattheir air quality standards are not sufficientlyprotected by IMO NOx and SOx codes. They haveimposed their own regulations to control marineemissions on a local basis. These include:-– Shutting down all engines and connecting to shore
supply– Using low sulphur fuel– Using exhaust aftertreatment
� The incentives are lower port fees
© Ricardo plc 2002 MARAD 2002 8
� NOx– High levels in performance (bsfc) optimised engines
� Particulate– High levels due to use of HFO
• Sulphur 4.5% max• Asphaltenes• Ash• Residues from lube oil additives
– Low load smoke
� Legislation and Standards– Proliferation of legislation– No common method of measurement of some key parameters,
e.g. smoke
© Ricardo plc 2002 MARAD 2002 9
Engine Injection timing retard + higher compression ratio+ more air
Fuel Injection System Changes to injection strategy. Rate shaping nozzle changes
Water Addition As emulsionDirect InjectionFumigation (HAM)
EGR not currently used due to particulate levels, but usebeing reviewed
Aftertreatment SCR very effective
© Ricardo plc 2002 MARAD 2002 10
0
20
40
60
80
100
IMOCompliance
InjectorChanges
WaterEmulsion
DirectInj. Water
Water+ EGR
SCR
NOx%
© Ricardo plc 2002 MARAD 2002 12
HAM - P rincipa l Layout
HAM unithumidifier
Catch tankHeat exchanger
Compressor Turbine
Courtesy of MAN B&W
© Ricardo plc 2002 MARAD 2002 14
� Problem with propulsion engines at low load, lowspeed– Due to : low injection pressure
low turbo boost pressure
� Solutions– Common rail injection system– More efficient turbochargers– Redesigned combustion chamber– Use of water emulsion
© Ricardo plc 2002 MARAD 2002 15
Fuel Injection System Higher injection pressuresCommon Rail (CR)Nozzle changes
Air Supply System More air at higher pressures
Base Engine Improved combustion chamberdesign
Aftertreatment Few, if any, systems in production,non-thermal plasma is showingpotential for future
© Ricardo plc 2002 MARAD 2002 18
Se rie sNe w conce pt
New cylinder head concept with newcombustion chamber geometry
Courtesy of MAN B&W
© Ricardo plc 2002 MARAD 2002 19
0
0,4
0,8
1,2
1,6
2
ne wcomb .cha mber
ne wcomb .cha mber
pre viouspre vious no zzle withsmaller bore s
nozzle withsmaller bo re s
TC withhig her e ff.
TC withhig her e ff.
limit of visibility
Improved combustion6L32/40 test engine, propeller operation
Smoke Index[ Bosch ]
Smoke emission at part load 25 %
Smoke emission at part load 25 %
Courtesy of MAN B&W
© Ricardo plc 2002 MARAD 2002 22
TMTM
Exhaustgas flow
Ground
High voltage
Courtesy of AEA Technology
© Ricardo plc 2002 MARAD 2002 23
� Current thermal efficiency levels– Medium speed 45-50%– Slow speed 48 - 51.5%
� Marine installations use waste heat recovery boiler to heat processsteam, further increasing efficiency
� Increases in overall engine efficiency depend on maximum cylinderpressure, turbocharger efficiency levels and fuel injection performance
� Work on reduced cooling loss combustion components can increaseefficiency by up to 4%– Wartsila ‘Hot combustion’ is an example of this– Other similar work is ongoing
� Use of steam bottoming cycles can significantly improve efficiency butat significant cost
� Ultimately price and availability of fuel will dictate use of post-engineenergy recovery devices
© Ricardo plc 2002 MARAD 2002 24
� LNG carriers– Reliquifaction of boil-off gas to use them in existing
diesel engines is now proven technology
– LNG fuelled oil rig supply vessel recently put intoservice in Norway
– Diesel engines can be converted to run on gas, butusually have to derate by 30% or more to avoid“knock”. Direct injection of gas avoids this derate butcarries a significant cost and fuel consumption penalty
© Ricardo plc 2002 MARAD 2002 25
� Technologies are becoming available to significantly reduceNOx levels without an excessive fuel consumption penalty.However, their effect on the long term durability of theengines has still to be quantified
� Significant reductions in the reduction of visible smokeemissions are now possible with new technologies, butmore work is needed
� Gas fuelled ships offer significant reductions in emissionslevels, but their use will be restricted to coastal traffic due tofuelling restrictions
� Increases in engine thermal efficiency are possible, but theemergence of these will be driven by economics
© Ricardo plc 2002 MARAD 2002 26
� Implementation of Marpol Annex VI needs to beconcluded as soon as possible
� An internationally recognised body should betasked to come up with single exhaust smokemeasuring procedure that is acceptable to enginebuilders, legislators and users
� Engine builders and users should be encouragedto come up with retrofit packages to improve theemissions of their existing ships
Top Related