19
Part Number Encoding Figure 3.3 identifies the significance of each character in the HarmonicGuard Active filter part number. An example of a completed part number would be ALC100A01H2000. This designates an enclosed HarmonicGuard Active filter that is rated for 100 amps, 480 volts, and has an HMI Interface Module Package.
HGA Part Numbering System – 480V Open and Type 1 Current: 45, 50, 90, 100, 200 Voltage: 480 Enclosure: Open Chassis or UL Type 1
Figure 3.3 – HarmonicGuard Active filter part number encoding
ALC 100 A 01 H 00 XX
ALC prefix
Current Rating
Voltage Rating
A= 480
Enclosure
00 = Open Chassis
01 = UL Type 1
Package Option
Circuit Breaker
H=Interface Module
10=ABB 22kA 20=ABB 100kA 30=A-B 25kA 40=A-B 65kA, 60=Eaton 65kA 70=Eaton 100kA, 80=Square D 18kA 90=Square D 65kA, 00=No breaker 01=ABB 65kA
Reserved for custom options to be defined as needed, each position can use 0 thru 9
45, 50, 90, 100, 200
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
HGA Ordering Instructions - HMI
Revision A
Page 12 January 1, 2015 Product & Price GuidePhone: 414-357-4480 Fax: 414-357-4484 www.transcoil.com
PART NUMBER TWO: HMI
Step 1) Based on the type of enclosure you are ordering, use one of the two Part Numbering Systems below to create your HMI part number:
• Figure 5: Open Chassis, UL Type 1 and UL Type 12• Figure 6: UL Type 3R
Step 2) Identify the required current, voltage and communication option to determine the second part number.
• Current RatingCorrective amp rating, see the HarmonicGuard Solution Center at www.transcoil.com/solutioncenter.htm
• Voltage RatingApplication voltage
• Communications Options - For Open Chassis, UL Type 1 and UL Type 12 the options include: ModBus RTU over RS485, Modbus TCP/IP, EtherNet I/P or DeviceNet (Figure 5)
- For UL Type 3R there is only one interface option which has no HMI display, but does have four status indicator lights, a run/stop key switch to control the unit and an external diagnostic port that an HGA-HMI unit, an optional addition, can be connected to (Figure 6). - The HGA-HMI is an HMI assembly inside a small portable case which can be ordered in addition to the required communication option. The part number to enter on your order is: HGA-HMI.
Figure 5: HMI Part Numbering System for Open Chassis, UL Type 1 and UL Type 12 units
Figure 6: HMI Part Numbering System for UL Type 3R units
CM 2 0 0 A R
HMI Part Numbering System: 3R
Current Rating
Voltage Rating A = 480C = 600 Type 3R
CM 2 0 0 A 0 1
HMI Part Numbering System
00 = Modbus® RTU over RS485
01 = EtherNet / IP & Modbus TCP/IP 02 = DeviceNet
Current Rating
Voltage Rating A = 480 C = 600 Communication Options
480V = 45, 50, 90, 100, 150, 200, 300600V = 039, 078
There is only one configuration of the HGA-HMI so there is only one part number for that which is HGA-HMI.
EtherNet/IP & Modbus TCI/IP are the same hard-
Top Related