SERVICE MANUAL
SI : TSE: Check: Approved:
Date Revise Version Description
2008.01.24 V1.0 Initial Issue
H5350
Copyright Jan,2008. All Rights Reserved P/N: 36.89T03G001
H5350:95.87U20G019;95.87U20GC0E
Emy Roch
H5350 Confidential
Preface
This manual is applied to H5350 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product.
Your customers will appreciate the quick response time when you immediately identify problems that occur with our products. We expect your customers will appreciate the service that you offer them.
This manual is for technicians and people who have an electronic background. Please send the product back to the distributor for repairing and do not attempt to do anything that is complex or is not mentioned in the troubleshooting.
Notice:
The information found in this manual is subject to change without prior notice. Any subsequent changes made to the data herein will be incorporated in future edition.
H5350 Service Manual
Copyright Jan.2008
All Rights Reserved
Manual Version 1.0
H5350 Confidential
Table of Content
Chapter 1 Introduction Highlight 1-1
Compatible Mode 1-3
Product Overview 1-7
Chapter 2 Disassembly Process Equipment Needed & Product Overview 2-1
Disassemble Lamp Cover Module 2-2
Disassemble Lamp Module 2-2
Disassemble Top Cover Module 2-3
Disassemble Top Shielding 2-4
Disassemble Main Board Module & I/O Cover Module 2-4
Disassemble Front Cover Module 2-6
Disassemble Engine Module 2-7
Disassemble Color Wheel Module 2-8
Disassemble Zoom Ring & Focus Ring 2-9
Disassemble DMD Board and DMD Chip Module 2-10
Disassemble Fan Module 2-11
Disassemble Blower Module 2-12
Disassemble Speaker Module 2-13
Disassemble LVPS Module 2-14
Disassemble Interrupt Switch Module 2-15
Disassemble Lamp Driver Module 2-16
Disassemble Bottom Cover Module 2-18
Rod Adjustment 2-19
Re-write Lamp Usage Hour 2-20
H5350 Confidential
Assemble Bottom Cover Module 2-21
Assemble Lamp Driver Module 2-22
Assemble Interrupt Switch Module 2-24
Assemble LVPS Module 2-25
Assemble Speaker Module 2-26
Assemble Blower Module 2-26
Assemble Fan Modul 2-27
Assemble DMD Board and DMD Chip 2-28
Assemble Zoom Ring&Focus Ring 2-29
Assemble Color Wheel Module 2-30
Assemble Engine Module 2-31
Assemble Front Cover Module 2-32
Assemble Main Board Module & I/O Cover Module 2-33
Assemble Top Shielding 2-34
Assemble Top Cover Module 2-35
Assemble Lamp Module 2-36
Assemble Lamp Cover Module 2-36
Chapter 3 Troubleshooting
LED Lighting Message 3-1 Main Procedure 3-2
Chapter 4 Function Test & Alignment Procedure
Test Equipment Needed 4-1
Service Mode 4-1
OSD Reset 4-1
Test Condition 4-2
Test Inspection Procedure 4-3
H5350 Confidential
PC Mode 4-3
Defectspecificationtable 4-7
Video Performance 4-7
Optical Performance Measure 4-9
Other 4-10
Chapter 5 Firmware Upgrade Equipment Needed 5-1
DLP Composer Lite Setup Procedure 5-2
USB Driver Upgrade Procedure 5-4
Firmware Upgrade Procedure 5-5
Chapter 6 EDID Upgrade EDID Introduction 6-1
Equipment Needed 6-2
Setup Procedure (VGA) 6-3
EDID Key-In Procedure 6-4
Setup Procedure (HDMI) 6-6
Appendix A Exploded Image I
Appendix B SerialNumberSystemDefinition XXI PCBACodeDefinition XXII
H5350 Confidential 1-1
Chapter 1
Introduction
1-1 Highlight
No Item Description1 Dimensions (WxHxD) - 267 mm X 187 mm X 80 mm 2 Weight - <5 lbs 3 Tilt Angle - 4 degree with elevator mechanism
4 Power Supply
- Universal AC 100 – 240 V ~ 50-60 Hz with PFC input - 180W for Osram E20.6 Lamp @ normal operation- Variant FAN speed control (Depends on temperature vari ance)
5 Keystone correction - +/ -40 degree (80 degree)
6 Cooling system
- Advanced Air Flow- Two fans with system acoustic noise level 35 dB(A) (typi cal)- Temperature control circuits with adaptive fan rotational speeds- Maximum touch temperature follow UL60950-1
7 Brightness -1700 ANSI Lumens (Typical; Full power mode)-1450 ANSI Lumens (Minimum; Full power mode)
8 Contrast- 1500 : 1 Full White and Black (Minimum; Full power mode)- 1800 : 1 Full White and Black (Typical; Full power mode)
9 Uniformity- 65% Japan standard (Minimum; Full power mode)- 80% Japan standard (Typical; Full power mode)
10 Throw ratio - 58”@2M(1.55 ~ 1.70 :1)11 Audio - 2W*1
12 Projection lens- F# 2.44~2.58, f = 21.83~23.81 mm, 1.10X Mechanical Zoom Lens
13 Lamp life - 3500 hours min, 50% survival rate14 System controller - TI DDP2230
H5350 Confidential 1-2
No Item Description
15 Terminal
- One HDMI input- One D-sub VGA input - One RCA Composite input- Three RCA Component input- One S-Video input(4 pin Mini din)- One audio input (2.5m phone jack)- One USB port (Type B Female)
16 Lamp housing
- Lamp Assembly could be changed by customer himself, but should read the user manual for instruction in advance.- Lamp Assembly should be provided by Coretronic and dis tributed through authorized agencies.
17 Input signal spec.
- Hsync Frequency 31 ~ 100 kHz- Vsync Frequency 56 ~ 85 Hz- Video Signal RGB (PC)● Analog RGB 0.7Vp-p, 75 ohm, Separate TTL H,V Sync● Analog RGB 1Vp-p, 75 ohm, Sync. On Green signal● Analog RGB 0.7Vp-p, 75 ohm, Composite TTL Sync.- Video● Composite video 1Vp-p,75 ohm● S-video Luminance 0.714Vp-p, 75 ohm● Chrominance 0.286Vp-p, 75 ohm● Component Video 1Vp-p, 75 ohm
18 TI DMD- TI DMD 0.62” 12° 2xLVDS Type-A 720p Digital Mirror Device
19 Video compatibility
- Standards :● NTSC (3.58/4.43)● PAL (B/D/G/H/I/M/N)● SECAM (B/D/G/K/K1/L)● HDTV - 480i,576i 480p, 576p, 720p, 1080i,1080p
20 XGA / Compression- Compression : by using “DDP2230” Chips can make image compression
21 Number of active dots - 1280(H) x 720(V)
22 Color wheel- 6 segments (R90/Y35/G90/C35/W28/B82)- 7200 rpm
23 Lamp- 180 – Watt OSRAM Lamp (user replaceable) for full power mode
24 Temperature- Operating: 5°C -- 35°C- Storage: -20°C -- 60°C
H5350 Confidential 1-3
1-2 Compatible Mode
Computer Compatibility (Analog)A. VGA Analog(1) VGA Analog - PC Signal
Modes Resolution V.Frequency[Hz]
H.Frequency[KHz]
VGA
640x480 60 31.5640x480 72 37.9640x480 75 37.5640x480 85 43.3720x400 70 31.5720x400 85 37.9
SVGA
800x600 56 35.2800x600 60 37.9800x600 72 48.1800x600 75 46.9800x600 85 53.7832x624 75 49.725
XGA
1024x768 60 48.41024x768 70 56.51024x768 75 601024x768 85 68.7
SXGA
1152x864 70 63.81152x864 75 67.51152x864 85 77.1
1280x1024 60 63.981280x1024 72 76.971280x1024 75 79.981280x1024 85 91.1
QuadVGA1280x960 60 59.71280x960 75 75.23
SXGA+ 1400x1050 60 63.98UXGA 1600x1200 60 75
Power Mac G4 640x480 66.6(67) 34.93Power Mac G4 800x600 60 37.9Power Mac G4 1024x768 60 48.4Power Mac G4 1152x870 75 68.68Power Mac G4 1280x960 75 75PowerBook G4 640x480 60 31.35PowerBook G4 640x480 66.6(67) 34.93PowerBook G4 800x600 60 37.9PowerBook G4 1024x768 60 48.4
H5350 Confidential 1-4
Modes Resolution V.Frequency[Hz]
H.Frequency[KHz]
PowerBook G4 1152x870 75 68.68PowerBook G4 1280x960 75 75i Mac DV(G3) 1024x768 75 60
(2) VGA Analog - Extended Wide timing
WXGA1280x768 60 48.361280x768 75 57.61280x768 85 68.63
Native
1280x720 60 451280x800 60 49.7021440x900 60 55.935
1680x1050 60 65.3
H5350 Confidential 1-5
B. HDMI Digital (1) HDMI – PC Signal
Modes Resolution V.Frequency[Hz]
H.Frequency[KHz]
VGA
640x480 60 31.5640x480 72 37.9640x480 75 37.5640x480 85 43.3720x400 70 31.5720x400 85 37.9
SVGA
800x600 56 35.1800x600 60 37.9800x600 72 48.1800x600 75 46.9800x600 85 53.7832x624 75 49.7
XGA
1024x768 60 48.41024x768 70 56.51024x768 75 601024x768 85 68.7
SXGA
1152x864 70 63.81152x864 75 67.51152x864 85 77.1
1280x1024 60 641280x1024 72 771280x1024 75 801280x1024 85 91.1
QuadVGA1280x960 60 601280x960 75 75.2
SXGA+ 1400x1050 60 65.3UXGA 1600x1200 60 75
Power Mac G4 640x480 66.6(67) 34.9Power Mac G4 800x600 60 37.9Power Mac G4 1024x768 60 48.4Power Mac G4 1152x870 75 68.7Power Mac G4 1280x960 75 75PowerBook G4 640x480 60 31.4
H5350 Confidential 1-6
Modes Resolution V.Frequency[Hz] H.Frequency [KHz]
PowerBook G4 640x480 66.6(67) 34.9PowerBook G4 800x600 60 37.9PowerBook G4 1024x768 60 48.4PowerBook G4 1152x870 75 68.7PowerBook G4 1280x960 75 75i Mac DV(G3) 1024x768 75 60
(2) HDMI – Extended Wide timing
WXGA1280x768 60 47.81280x768 75 60.31280x768 85 68.6
(Native)
1280x720 60 44.81280x800 60 49.61440x900 60 59.9
1680x1050 60 65.3(3) HDMI – Video SignalFor TWN/USA SKU
480i (NTSC) 720x480(1440x480) 59.94(29.97) 15.7480p (NTSC) 720x480 59.94 31.5720p (NTSC) 1280x720 60 451080i (NTSC) 1920x1080 60(30) 33.71080p (NTSC) 1920x1080 60 67.4
For EMEA SKU576i (PAL) 720x576(1440x576) 50(25) 15.6576p (PAL) 720x576 50 31.3720p (PAL) 1280x720 50 37.51080i (PAL) 1920x1080 50 28.11080p (PAL) 1920x1080 50 56.3
Graphic source monitor range limits
Horizontal scan rate: 31k-100kHzVertical scan rate: 56-85Hz
H5350 Confidential 1-7
Product Overview
Projector Outlook
Front /Upper side
Item Description Item Description1 Zoom ring 5 Power button and Power Indicator LED2 Focus ring 6 Remote control3 Zoom lens 7 Remote control receiver4 Lens cap
H5350 Confidential 1-8
Rear side
Item Description Item Description1 USB connector 6 Composite video input connector2 HDMI connector 7 Audio input connector
3 Analog RGB/component inputconnector 8 Power socket
4 Component video input connector 9 KensingtonTM lock port5 S-Video input connector
H5350 Confidential 1-9
Remote Control and Control Panel Layout
H5350 Confidential 1-10
Item Icon Function Description
1 Infraredtransmitter Sends signals to the projector.
2 Power/PowerLED Power button and Power Indicator LED.
3 POWER Refer to the “Turning the Projector On/Off” section.
4 MENU
• Press “MENU” to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu.• Confirm your selection of items.
5 Four directionalselect keys
Use up, down, left, right buttons to select items or makeadjustments to your selection.
6 ZOOM Zooms the projector display in or out.7 ASPECT RATIO To choose the desired aspect ratio (Auto/4:3/16:9/L.Box).8 KeyPad 0~9 Press “0~9” to input a password in the “Security settings”.
9 KEYSTONE Adjusts the image to compensate for distortion caused bytilting the projector (± 40 degrees).
10 RESYNC Automatically synchronizes the projector to the input source.
11 SOURCE Press “SOURCE” to choose RGB, Component, S-Video,Composite and HDTV sources.
12 HIDE Momentarily turns off the video. Press “HIDE” to hide theimage, press again to display the image.
13 Empoweringkey Unique Acer functions: eView, eTimer Management.
14 FREEZE To pause the screen image.
Note:
H5350 Confidential 1-11
Remote Control Placement
Please refer to the illustration to attach the remote control to the projector.
H5350 Confidential 1-12
Connecting the Projector
Item Description Item Description1 Power cord 6 HDMI cable2 USB cable 7 RCA component cable for YPbPr3 VGA cable 8 S-Video cable4 Composite video cable 9 Audio cable Jack/RCA5 Audio cable Jack/Jack
Note: To ensure the projector works well with your computer,please make sure the
timing of the display mode is compatible with the projector.
H5350 Confidential 1-13
H5350 Confidential 1-14
Bottom Cover Dimension
H5350 Confidential 2-�
Chapter 2
Disassembly& Assembly Process2-1 Equipment Needed & Product Overview
1. Screw Bit (+) :107
2. Hex Sleeves 5mm
3. Screw Bit (+) :102
4. Screw Bit (-) :102
5. Long Nose Nipper
6. Tweezers
7. H5350 unit
* Before you start: This process is protective level II. Operators should wear electrostatic chains.
* Note: If you need to replace the main board, you have to get into service mode and record the
lamp usage hour. please refer to section 2-20.
H5350 Confidential 2-2
2-3 Disassemble Lamp Module
1. Unscrew 2 screws on Lamp Module
2. Disassemble Lamp Module
2-2 Disassemble Lamp Cover Module
1. Unscrew 2 screws on Lamp Cover Module
2. Disassemble Lamp Cover Module
Lamp Module
Lamp Cover Module
H5350 Confidential 2-3
2-4 Disassemble Top Cover Module
1. Unscrew 2 screws on the unit base
2. Disassemble Top Cover Module(As the
picture show)
Note: - You should drop out
of three tenons first, and then push
the Top Cover Module to back.
Top Cover Module
H5350 Confidential 2-�
2-5 Disassemble Top Shielding
1. Unscrew 7 screws on Top Shielding
2. Disassemble Top Shielding
2-6 Disassemble Main Board Module & I/O Cover Module
1. Unscrew 2 hex screws
2. Tear a tape
3. Unscrew 1 screw and 6 connectors on
Main Board Module
Top Shielding
H5350 Confidential 2-5
4. Pull up the Main Board Module and then
unplug 1 connector(As green square)
5. Disassemble Main Board Module and I/O
Cover Module6. Unscrew 3 screws to disassemble I/O
Cover Module from Main Board Module
I/O Cover Module Main Board Module
H5350 Confidential 2-�
2-7 Disassemble Front Cover Module
1. Unscrew 1 screw(As yellow circle)
2. Press 1 tenon on each side and then pull
up the Front Cover Module
3. Disassemble Front Cover Module
Front Cover Module
H5350 Confidential 2-7
2-8 Disassemble Engine Module
1. Pull the higher-part of Mylar up(As the
red square)
2. Unscrew 4 screws on Engine Module
3. Disassemble Engine Module
Engine Module
H5350 Confidential 2-�
2-9 Disassemble Color Wheel Module
1. Unscrew 2 screws to disassemble Color
Wheel Module
2. Unscrew 1 screw to disassemble Photo
Sensor Board from Color Wheel Module
Color Wheel Module
Photo Sensor Board
H5350 Confidential 2-�
2-10 Disassemble Zoom Ring & Focus Ring
1. Unscrew 2 screws on Engine Module to
disassemble the Zoom Ring and Zoom
Ring Holder
2. Unscrew 3 screws to disassemble Focus
Ring
Focus Ring
Zoom Ring Holder and Zoom Ring
H5350 Confidential 2-�0
2-11 Disassemble DMD Board and DMD Chip
1. Unscrew 4 screws on Engine Module to
disassemble Heat Sink
2. Unscrew 4 hex screws to disassemble
DMD Board and DMD Chip
Heat Sink
H5350 Confidential 2-��
2-12 Disassemble Fan Module
1. Unscrew 4 screws
2. Take the Fan Cable out of the aperture
(As the red square)
H5350 Confidential 2-�2
2-13 Disassemble Blower Module
1. Unscrew 3 screws to disassemble Blower
Module
2. Disassemble Rubber from the Blower
3. Unscrew 4 screws to disassemble Fan
Module
4. Unscrew 1 screw to disassemble Thermal
Switch
H5350 Confidential 2-�3
2-14 Disassemble Speaker Module
1. Unscrew 1 screw and press 2 tenons to
disassemble Speaker Module
Note: - Use the tweezers to press the tenon.
2. Press the two tenons outward to
disassemble the Speaker from the
Speaker Holder
H5350 Confidential 2-��
2-15 Disassemble LVPS Module
1. Unscrew 1 ground screw(As red circle)
2. Unscrew 1 screw on LVPS Module(As
yellow circle) to disassemble LVPS BRKT
3. Unscrew 3 screws on LVPS Module(As
green circle)
4. Unplug 2 connectors to disassemble
LVPS ModuleLVPS BRKT
LVPS Module
H5350 Confidential 2-�5
2-16 Disassemble Interrupt Switch Module
1. Unscrew 1 screw and disassemble 1 Film
Tape to disassemble Interrupt Switch
Module
2. Tear off a Mylar
3. Press 2 tenons to disassemble Interrupt
Switch from Interrupt Switch Holder
Interrupt Switch Module
Film tape
Aperture
Dent
H5350 Confidential 2-��
2-17 Disassemble Lamp Driver Module
1. Unscrew 1 screw to disassemble Lamp
Driver Module
2. Unplug 1 connector(As red square) and
unscrew 2 screws (As green circle) to
disassemble Lamp Driver to Lamp Cable
3. Disassemble 1 Mylar(As green square)
Lamp Driver to Lamp Cable
H5350 Confidential 2-17
4. Unplug 2 connectors to disassemble 2PIN
and 5PIN cable
5. Unscrew 4 screws to disassemble Lamp
Driver from Lamp Driver Holder
2 PIN&5 PIN Cable
Lamp Driver HolderLamp Driver Module
H5350 Confidential 2-��
2-18 Disassemble Bottom Cover Module
1. Unscrew 1 screw on Bottom Cover
Module
2. Tear 1 EMI tape
3. Disassemble the Bottom Cover Shielding
from Bottom Cover Module
�. Pull aside the iron sheet with Tweezers
to disassemble the ROD DUCT from
Bottom Cover Module
Note: - Due to the iron sheet is out of shape
easily,so we must turn it back before
assemble the ROD DUCT.
5. The disassembly is completed
Bottom Cover ModuleBottom Cover Module Shielding
ROD DUCT
H5350 Confidential 2-��
2-19 Rod Adjustment
1. Environment adjustment
- The distance between the engine and the
screen is 2.25 M
- This process should be done at a dark
environment. (under 5 Lux)
2. Procedure adjustment
- Change the screen to “white screen.”
- Adjust the screws by using the rod on
the engine module to readjust the image.
(adjust until the yellowish or bluish parts
disappeared.)
3. Abnormal image inspection
- It should not have any abnormal color at
the rim of the image by estimating through
the eyes.
Note: - To avoid over adjust the rod.
- “Screw 1” should be adjusted first, and
then adjust the “Screw2”.After the
adjustment, use the glue to fix the
screws.
1
2
H5350 Confidential 2-20
2-20 Re-write Lamp Usage Hour
1. Get into service mode.
- press (power > left > left > menu) to get
into service mode.
- Click “RD Test” to get into the next step
2. Select “Lamp life” and use left or right key
to re-write the lamp hour back to previous
lamp usage hour.
3. Choose “Return to Service Menu” and
then exit the service mode
Note: left key = decrease lamp hour
right key =increase lamp hour
Check the lamp usage hour
Re-write lamp usage hour
H5350 Confidential 2-2�
2-21 Assemble Bottom Cover Module
1. Assemble ROD DUCT on the Iron Sheet
2. Assemble the Bottom Cover Shielding on
Bottom Cover Module
3. Stick 1 EMI tape
4. Screw 1 screw on Bottom Cover Module
Bottom Cover ModuleBottom Cover shielding
H5350 Confidential 2-22
2-22 Assemble Lamp Driver Module1. Screw 4 screws to assemble Lamp
Driver Module on Lamp Driver Holder
2. Plug 2 connectors to assemble 2PIN and
5PIN cable
Note: - The 2 PIN and 5 PIN cable must be pass
through a Dent.(As the yellow square)
3. Stick a Mylar
2 PIN&5 PIN Cable
Lamp Driver HolderLamp Driver Module
Lamp Driver to Lamp Cable
H5350 Confidential 2-23
4. Plug 1 connector(As blue square)and
screw 2 screws to assemble Lamp Driver
to Lamp Cable
Note: - The lamp driver to lamp cable must be
passed through two Dents.(As the yellow
square)
5. Screw 1 screw on Lamp Driver Module
H5350 Confidential 2-2�
Interrupt Switch Module
2-23 Assemble Interrupt Switch Module
1. Fasten 2 tenons to assemble Interrupt
Switch on Interrupt Switch Holder
2. Stick a Mylar on Interrupt Switch Module
3. Screw 1 screw and stick 1 film tape to
assemble Interrupt Switch Module
Note: - Interrupt Switch cable must be passed
through a dent and a aperture.And use
a film tape to fix the cable in the dent.
Film tape
Aperture
Dent
H5350 Confidential 2-25
2-24 Assemble LVPS Module
1. Plug 2 connectors (As yellow square)
and screw 3 screws (As green circle) to
assemble LVPS module
2. Screw 1 screw to assemble LVPS BRKT
(As yellow circle)
3. Screw 1 ground screw(As red circle)
LVPS BRKT LVPS Module
H5350 Confidential 2-2�
2-25 Assemble Speaker Module
1. Fasten 2 tenons to assemble the
speaker on the speaker holder
2. Fasten 2 tenons and screw 1 screw to
assemble Speaker Module
.
2-26 Assemble Blower Module
1. Assemble the Rubber on the Blower
2. Screw 3 screws to assemble Blower
Module
H5350 Confidential 2-27
2-27 Assemble Fan Module
1. Screw 1 screw to assemble
Thermal Switch(As green circle)
2. Screw 4 screws to assemble Fan Module
3. Screw 4 screws to assemble Fan Module
on the unit
Note: - The fan cable pass through from the
aperture.
H5350 Confidential 2-2�
2-28 Assemble DMD Board and DMD Chip1. Screw 4 hex screws to assemble all
components of DMD parts
2. Screw 4 screws on Engine Module to
assemble Heat Sink
H5350 Confidential 2-2�
2-29 Assemble Zoom Ring&Focus Ring
1. Screw 3 screws to assemble Focus Ring
2. Screw 2 screws on Engine module to
assemble Zoom Ring and Zoom Ring
Holder
Zoom Ring Holder and Zoom Ring
H5350 Confidential 2-30
2-30 Assemble Color Wheel Module
1. Screw 1 screw to assemble Photo
Sensor on Color Wheel Module
2. Screw 2 screws to assemble Color
Wheel Module
H5350 Confidential 2-3�
2-31 Assemble Engine Module
1. Push the higher-part of Mylar down(As the
red square) to assemble Engine Module
2. Screw 4 screws to assemble Color Wheel
Module
H5350 Confidential 2-32
2-32 Assemble Front Cover Module
1. Push down the Front Cover Module
2. Fasten 1 tenon on each side
3. Screw 1 screw(As yellow circle) to
assemble Front Cover Module
H5350 Confidential 2-33
2-33 Assemble Main Board Module & I/O Cover Module
1. Screw 3 screws to assemble I/O
Cover Module on Main Board Module
2. Plug 1 connector(As green square)
3. Screw 1 screw and 6 connectors on
Main Board Module
4. Stick a tape
I/O Cover Module Main Board Module
H5350 Confidential 2-3�
5. Screw 2 hex screws
2-34 Assemble Top Shielding
1. Screw 7 screws on the Top Shielding
H5350 Confidential 2-35
2-35 Assemble Top Cover Module
1. Fasten 3 tenons to assemble Top
Cover Module on the unit
Note: - You should press three tenons first,
and then push the Top Cover Module
to back.
2. Screw 2 screws on the unit base
H5350 Confidential 2-3�
2-36 Assemble Lamp Module
1. Assemble Lamp Module
2. Screw 2 screws on Lamp Module
2-37 Assemble Lamp Cover Module
1. Assemble Lamp Cover Module
2. Screw 2 screws on Lamp Cover Module
3. Assembly is completed
Lamp Cover Module
H5350 Confidential 3-�
Chapter 3
Troubleshooting3-1 LED Lighting Message
MessagePower LED
Red Blue
Input Power Plug Flash ON to OFF 100ms --
Standby V --
Power button ON -- V
Lamp retry -- Quick Flashing
Power off (Cooling state) Quick Flashing --
Power button OFF:Cooling completed;
Standby ModeV --
Error (Thermal Failure) Quick Flashing RED and Steady BLUE by returns
Error (Fan lock) Quick Flashing RED and Steady BLUE by returns
Error (Lamp break-down) Quick Flashing BLUE and Steady RED by returns
Error (Color Wheel fail) Quick Flashing BLUE and Steady RED by returns
H5350 Confidential 3-�
3-2 Main Procedure
No Symptom Procedure
� No Power
- Ensure the Power Cord and AC Power Outlet are securely connected
- Check Lamp Cover and Interrupt Switch
- Ensure all connectors are securely connected and aren’t
broken
- Check Lamp Driver
- Check LVPS
- Check Main Board
� Auto Shut Down
- Check LED Status
a. Lamp LED Light
- Check Lamp
- Check Lamp Driver
- Check Main Board
b. Temp LED Light
- Check Thermal Switch
- Check Fan
c. Color Wheel
- Check Color Wheel
- Check Photo Sensor
H5350 Confidential 3-3
No Symptom Procedure
3 No Image
- Ensure the Signal Cable and Source work
(If you connect multiple sources at the same time, use the “Source” button switch)
- Ensure all connectors are securely connected and aren’t
broken
- Check Main Board
- Check DMD Board
- Check DMD Chip
- Check Engine Module
4 No Light On
- Ensure all connectors are securely connected and aren’t broken
- Check Lamp Module
- Check Lamp Driver
- Check LVPS
- Check Main Board
5 Machanical Noise- Check Color Wheel
- Check Fan Module
6 Line Bar/Line Defect
- Check if the Main Board and the DMD Board are
assembled properly
- Check Main Board
- Check DMD Board
- Check DMD Chip
7 Image Flicker
- Do “Reset(All data)” of the OSD Menu
- Ensure that the signal cables and source are work as well
- Check Lamp Module
- Check Color Wheel
- Check DMD Board
- Check Main Board
H5350 Confidential 3-4
No Symptom Procedure
8 Color Abnormal
- Do “Reset(All data)” of the OSD Menu
- Adjust Color Wheel Index
- Check Main Board
- Check Color Wheel
9 Poor Uniformity/Shadow
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
- Ensure the Brightness is within spec
- Check rod alignment
- Check Engine Module
�0 Dead Pixel/Dust(Out of spec.)
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
- Clean DMD Chip and Engine Module
- Check DMD Chip
- Check Engine Module
�� Garbage Image
- Ensure that the signal cables and source work as well
- Check Main Board
- Check DMD Board
�� Remote Control
- Remote Control
a.Check Battery
b.Check Remote Controller
c.Check Main Board
�3 Function Abnormal
- Do “Reset(All data)” of the OSD Menu
- Check Main Board
- Check DMD Board
�4 Audio Abnonrmal
- Ensure that the signal cables and source are work as well
- Check Speaker Module
- Check Main Board
H5350 Confidential 3-5
No Symptom Procedure
�5Forgetting Password (adminstrator Password)
- An unique Universal Password which is printed on the Security Card. This unique password is a back door of Administrator Password which will be accepted by projector anytime no matter what the Administrator Password is.
- How to get the Universal Password? (1) Click the “AcerSNID”
(2) Input SNID number.(SNID number is on the Security Card)
(3) Click“Calculate”.Then the Universal Password will appear.
H5350 Confidential 4-�
Chapter 4
Function Test & Alignment Procedure
4-1 Test Equipment Needed
- IBM PC with XGA resolution and Wireless Network Card
- DVD player with Multi-system (NTSC/PAL/SECAM), equipped “Component”, “S-Video”
, “Composite” and "HDMI".
- HDTV Source (480P, 720P, 1080i)
- Minolta CL-100
- Quantum Data 802B or CHROMA2327 (Color Video Signal & Pattern Generator)
- After changing parts, check the information below.
4-2 Service Mode
1. Turn on the projector and input the signal
2. Do the following actions sequentially to enter service mode menu
(1) Press "Power→Left→Left→Menu".
(2) Service mode will be shown.
(3) After confirming the configuration, press "Exit" to exit.
4-3 OSD Reset
1. After final QC step, we have to erase all saved change again and restore the OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting:
(1) Please enter OSD menu.
(2) To execute "Reset" function.
H5350 Confidential 4-2
4-4 Test Condition
- Circumstance brightness: Dark room less than 5.0 lux.
- Inspection distance: 1.8m~2.5m functional inspection.
- Screen size: 60 inches diagonal
- After repairing each H5350, the unit should be run-in (refer to the table below)
Symptom Run-in TimeNormal repair 2 hoursNFF 4 hoursAuto shut down 6 hours
- Enter Burn-In Mode* Cycle setting is based on the defect symptoms. ie: If it is NFF, the run-in time is 4 hours. You have
to set the lamp on for 50 min. and lamp off for 10 min for 4 cycles.
Press power > left > left > MenuChoose Burn-In Test > enterLamp On (Min) Press right key to adjust the time (50)Lamp Off (Min) Press right key to adjust the time (10)Set burn in cycle Press right key to adjust the cycleAfter setting up the time, choose Burn-In mode and hit enter
Screen Defects (While replacing DMD Chip, DMD BD and MB)
< Figure: Zone A &B Definition >
H5350 Confidential 4-3
4-5 Test Inspection Procedure
Charge parts/ Update M/B FW Color Wheel Lamp Module
Version Update v vColor Wheel Index v v
PC Calibration
YPbPr Calibration
Reset lamp hour vOSD Reset v v
EDID vRe-write Lamp
Hour Usage v
4-6 PC MODE
1. Frequency and tracking boundry
Procedure - Test equipment: video generator. - Test signal: analog 1280 x 720@60Hz - Test Pattern: general-1 or master - Check and see if the image sharpness is well-
performed. - If not re-adjust by the following steps: (1) Select "Frequency" function to adjust the
total pixel number of pixel clock in one line period.
(2) Select "Tracking" function and use right or left arrow key to adjust the value to minimize
General-1
Master
H5350 Confidential 4-4
video flicker. - Adjust Resync or Frequency/Tracking/H. Posi-
tion/V. Position to the inner screen.Inspection item - Eliminate visul wavy noise by Rsync, Frequency
or Tracking selction. - Check if there is noise on the screen. - Horizontal and vertical position of the vedio
should be adjustable to the screen frame.Criteria - If there is noise on the screen, the product is
considered as faliure product. - If there is noise on the screen, use auto or
manual “frequency” function or “tracking” func-tion to adjust the screen.
- The PC mode functionally sure be workable include support format with frequency and auto detected functional will be workable.
2. Light Leak
Procedure - Test equipment: video generator. - Test signal: analog 1280 x 720@60Hz1280 x 720@60Hz - Test Pattern: gray 30 patterns - Check if the light leaks. * Light leak on reflective edge, eyecatcher, bond-
wires and exposed metal.Inspection item - Light leak check. - Bright blemish (dirty).Criteria - The pattern cannot accept the color level of the
leakage is brighter than the gray 30 pattern. - Ref. below table Note: The defect criteria follows TI specification.
3. Blemish (Dark)
Procedure - Test equipment: video generator. - Test signal: analog 1280 x [email protected] x 720@60Hz.. - Test Pattern: blue 60
Gray 30
Blue 60
H5350 Confidential 4-5
Inspection item - Dark blemish check.(dirty)Criteria - The bright blemish is unacceptable when it ap-
pears on blue 60 pattern. - Ref. below table Note: The defect criteria follows TI specification.
4. Dead Pixel (Bright pixel)
Procedure - Test equipment: video generator. - Test signal: analog 1280 x [email protected] x 720@60Hz.. - Test Pattern: full blackInspection item - Bright pixel check. Note: Frame dimension under operative zone1
inchCriteria - Bright pixel is unacceptable. - Ref. below table Note: The defect criteria follows TI specification.
5. Dead Pixel (Dark pixel)
Procedure - Test equipment: video generator. - Test signal: analog 1280 x [email protected] x 720@60Hz.. - Test Pattern: full whiteInspection item - Dead pixels check. - White pattern (IRE=100) - Adjacent dark pixel.Criteria - The number of the dead pixels should be less or
equal to 6 pixels. - Adjacent pixel with each other is unacceptable. - Ref. below table Note: The defect criteria follows TI specification.
6. Focus test
Procedure - Test equipment: video generator. - Test signal: analog 1280 x 720@60Hz1280 x 720@60Hz
Full black
Full white
H5350 Confidential 4-6
- Test Pattern: full screen or MEME Sony Inspection item - Focus check
Criteria - From screen 2.25 M via visual to check the focus, look at the entire screen, focus shall be clear, crisp, and sharp over the entire surface of the display pattern.(Blur word on one of the corner after adjustment is acceptable. However, the word should at least be recognizable.)
7. Color performance
Procedure - Test equipment: video generator. - Test signal: HDMI 720p,1080i - Test Pattern: Master, In focus II or SMPTE RP-
�33 * Please refer to 4-2 to enter service mode.
Use 720P & 1080i signal, master pattern to do HDTV test. Color cannot discolor to purple and blue. If the test result is discoloration or flicker-ing, please return the unit back to repair
centers.Inspection item - Check if each color level is well-functioned. - color saturations
Criteria - Screen appears normal. It should not have any abnormal condition, such as lines appear on the screen and so on.
- Color appears normal. - It is acceptable to have few lines flashing at the
center and on the edge of 1080i image. How-ever, rest of the image should appears stable.
- RGBW should all appear normal on the screen and sort from R -G-B-W.
- Color levels should be sufficient and normal. (the unidentified color levels on both left and right sides should not over 8 color levels.)
- Grey level should not have abnormal color or SMPTE RP-133
InFocus II / 64 gray RGBW
Master
MEME Sony
Full screen
H5350 Confidential 4-7
heavy lines. - The PC mode functionally sure be workable
include support format with frequency and auto detected functional will be workable
4-7 Defect specification table
Order Symptom Pattern Criteria
� Bright pixel ( dots) Black pattern
( IRE=O)A+B=0
2 Dark pixel(dots) White patternA+B=6
3 Unstable pixel (dots) Any pattern A+B=1
4 Adjacent dark pixel (dots) Any pattern
A+B=0
5 Dark blemish (Dirty) Blue 60 patternA+B=3
(diameter <1/2 inch)
6 Bright blemish (Dirty) Gary 30 patternA+B=3
(diameter <1/2 inch)
7 Bright dot on frame Black pattern 2
4-8 Video Performance
1. CVBS
Procedure - Test equipment: DVD player - Test signal: CVBS
Motion video
H5350 Confidential 4-8
Inspection item - Video performance testInspection Distance - 1.8M ~2.5M Criteria - Check any abnormal color, line distortion or anyabnormal color, line distortion or any color, line distortion or any
noise on the screen. - Check the sound from speakers.
2. S-VideoProcedure - Test equipment: DVD player - Test signal: S-Video
Inspection item - Video performance testInspection Distance - 1.8M ~2.5M Criteria - Check any abnormal color, line distortion or any
noise on the screen. - Check the sound from speakers.
3. HDTV/ Component
Procedure - Test equipment: DVD player - Test signal: Ycbcr/YPbPr Inspection item - HDTV performance testInspection Distance - 1.8M ~2.5MCriteria - Check any abnormal color, line distortion or anyabnormal color, line distortion or any color, line distortion or any
noise on the screen. - Check the sound from speakers.
4. Audio Test
Procedure - Test equipment: DVD player - Test signal: CVBS Inspection item - Audio performance testInspection Distance - 1.8M ~2.5MCriteria - Check the sound from speakers. - Check “Volume” is normal - Check “Mute” is normal
5. HDMI test
Procedure - Test Signal : 720p,1080i
H5350 Confidential 4-�
- Test Pattern : Any Pattern - Equipment: DVD Player with HDMI output - Display type must be set to 16:9Inspection item - HDMI TestCriteria - Ensure if the image is well performed and the color can not discolor.
4-9 Optical Performance Measure
Inspection Condition- Environment luminance: 5 Lux
- Product must be warmed up for 3 minutes
- Distances from the screen: 2.25 M
- Screen Size: 60 inches diagonal
- Reset to default before measurement
1. Test equipment
Procedure - Enter service mode:Press "Power→Left→ Left→Menu". - Select “RD test” - Select “Spoke On”
2. Brightness Procedure - Full white pattern - Use CL100 to measure brightness values of P1~P9. - Follow the brightness formula to calculate brightness values. ☼ Brightness Formula Avg.(P1~ P9)x1.1m2 Criteria - 800 lumens
Full white pattern
H5350 Confidential 4-�0
3. Ful On/Full Off Contrast Procedure - Full white pattern & full black pattern - Use CL100 to measure brightness values of full
white pattern P5 & full black pattern B5 ( see im-age: full white)
- Follow Contrast formula to calculate contrast values.
☼ Contrast Formula P5/B5 note: P5=center of white image B5=center of black image.Criteria - 1500:1
4. Uniformity
Procedure - Full white pattern - Use CL100 to measure brightness values of
P1~P9 (see image: full white). - Follow the Uniformity formula to calculate average values. ☼ Uniformity Formula ANSI Uniformity = Avg. (P1, P3, P7, P9) P5Criteria - 65%
4-11 Others
1. Functional Inspection
Keypad button - All keypad buttons must operate smoothly.
General - All OSD functions must be checked for functionality. When OSD menu is displayed, there
x 100%
Full black pattern
H5350 Confidential 4-��
shall be no visible peaking, ringing, streaking, or smearing artifacts on the screen.
Factory Default - The factory settings (with appropriate centering, size, ge-ometry distortion, etc.) shall be displayed upon “Recall” is selected from OSD
Display Size - All preset modes shall expand to full screen size using OSD Horizontal and Vertical Size controls
Display Data Channel (DDC) - The purpose of the DDC test is to verify the DDC1/DDC2B operation of the projector and to verify Plug & Play function.
Acoustic - High pitch sound from cooling fan and color wheel is unac-ceptable.
2. Check points for exterior and print pattern
Check item Check point
Text & Pattern Missing letters & pattern or blurry prints are unacceptable
Exterior Dirt, scrape, water ripples and uneven color are unacceptable
Buttons Stuck buttons are unacceptableFocus ring Focus ring is functioning smoothly
Logo Missing logo, missing prints and blurry prints are unacceptable
Screw All screw sure be fixed and in right typePedestal Well-functionedLamp Cover It should be locked in the correct placePlastic Parts All plastic parts can not be brocken and damagedSafety or warning label
All safety and warning label should be visible, including all contents
Connector All interface connector should be complete and workable
H5350 Confidential 5-�
Chapter 5
Firmware Upgrade5-1 Equipment Needed
Software : (DDP 2230- USB)- DLP Composer
- Firmware
- Library V7.1 0330 (library file has to put in PC and set right path in 5-4 step 4)
Hardware : - Projector
- Power cord (42.53506G002)
- USB Cable (42.87304G001)
- PC or Laptop
H5350 Confidential 5-2
5-2 DLP Composer Lite Setup Procedure
1. Choose "DLP Composer Lite V7.1 Setup"
Program.
2. Click "Next" button.
3. Read "License Agreement".
- Choose "I accept and agree to be bound
by all the terms and conditions of this
License Agreement".
4. Click "Next".
5. Click "Next".
4
3
H5350 Confidential 5-3
6. Click "Next".
7. Click "Next".
8. Writing system registry values.
9. Click "Finish".
H5350 Confidential 5-4
5-3 USB Driver Upgrade Procedure
1. set up
- Plug in Power cord to projector.
- Link PC USB port and projector USB port
by USB Cable.
2. Execute Program
(1) "Found new hardware wiszard" will be
appearred on the screen.
(2) Select "Install the software automatically
(Recommended)".
(3) Then click "Next".
3. Finish
- Click "Finish" to end the installation.
(2)
(3)
H5350 Confidential 5-5
5-4 Firmware Upgrade Procedure
1. Set-up
- Hold on "Power" and plug in power cord
while holding on "Power".
- Once the Power LED light on Blue & Red
at the same time, plug in USB cable into
the projector and link to the USB port of a
PC.
Note: The system fan and the light will not
operated.
2. Execute the "DLP ComposeTM" file.
3. Click "edit" and "perferences".
4. Click “Library.”
- Click the “browse” button and navigate to
the directory where you put the library file
in.
H5350 Confidential 5-6
5. Select "Edit\preferences\Communications"
- Choose "USB".
- Click "OK".
6. Choose "Flash Loader".
- Click "Browse" to search the firmware file.
7. Selete the item "skip Boot Loader Area"
(select 32KB).
- Click "Reset Bus" to erase the flash
memory.
8. If the firmware is ready, click "start
download" to process the firmware
upgrade.
- Click "Yes" to erase the flash memory.
H5350 Confidential 5-7
9. When firmware upgrade process is
finished, the unit return to stand-by status.
The LED power lights on and appears Red.
- Unplug USB cable and power cord and
replug in power cable.
10. Restart the unit and enter the service
mode to check the firmware version.
(To enter service mode, please refer to
Chapter 4 Function Test and Alignment
Procedure.)
32
H5350 Confidential 6-�
Chapter 6
EDID Upgrade
6-1 EDID Introduction
Extended Display Identification Data is a VESA standard data format that contains basic
information about a display device and its capabilities, including vendor information,
maximum image size, color characteristics, factory pre-set timings, frequency range limits,
and character strings for the monitor name and serial number.
The information is stored in the display and is used to communicate with the system
through a Display Data Channel (DDC), which sites between the display device and the
PC graphics adapter. The system uses this information for configuration purposes, so the
monitor and system can work together.
Note: If a display device has digital input ports, like DVI or HDMI, but without EDID in its
main board, the display device will show no image while the input source is digital signal.
H5350 Confidential 6-�
6-2 Equipment Needed
Software- EDID Program (Generic V0.51)
- EDID File (ACER_H5350 EDID-A04_USA.ini)
Hardware - Projector
- Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed)
- Power cord for Projector (42.53506G002)
- RS-232 9 Pin Cable (pin to pin, F-M) (42.83C07G001)
- Monitor
- PC
- VGA cable (42.87305G102)
- DVI Cable (42.83N06G001)
- Power adapter (47.57803G001) and power cord (42.53506G002) for fixture
- Adapter HDMI(M) to DVI-D(F) (42.82B13G001)
H5350 Confidential 6-3
6-3 Setup Procedure (VGA)
1. Connect all ports
(1) Connect P1 of Fixture with COM Port of
PC/Laptop by RS232 Cable.
(2) Connect P2 of Fixture with VGA port of
Projector by VGA Cable.
(3) Plug Power Adapter to Power CNN.
(4) Plug Power Cord to H5350 unit.
Note: Confirm JP3 is "Close" status.
P1P2
Power CNN
VGA PortPower Port
VGA
H5350 Confidential 6-4
6-4 EDID Key-In Procedure
1. Execute EDID Program
(1) Click on "EDID" to execute EDID
program.
2. Process
(1) Check the COM port is "COM 2"
(Select the COM port which you are
using).
(2) Click the "Model" button.
(3) Choose the source file
"ACER_H5350 EDID-A04_USA.ini"
and then open it.
3. Process
(1) Key in the serial number into the
barcode blank space.
(2) In "Write Source Select" item,select
"Analog".
(3) Click "Program" button.
4. Process
(1) "Please change the cable to Analog"
will be shown on the screen.
(2) Please press "Ok" button.
(1)
(2)
(3)
2
3
(3)
(1)
(2)
1
4
H5350 Confidential 6-5
5
6
7
5. Finish
(1) "OK" will be shown on the screen.
6. Read EDID information
(1) In the Read item,select "Analog" and
"Trans".
(2) Please press "Read" button.
7. Read EDID information
(1) EDID Informations will show the result.
H5350 Confidential 6-6
6-5 Setup Procedure (HDMI)
1. Connect all ports
(1) Connect P1 of Fixture with COM Port of
PC/Laptop by RS232 Cable.
(2) Connect P2 of Fixture with P3 by DVI
Cable.
(3) Plug P4 to HDMI Port of the Projector.
(4) Plug Power Adapter to Power
CNN.
(5) Plug Power Cord to H5350 unit.
Note: Confirm JP3 is "Close" status.
P2
Power CNN
P1
P3
P4
Power PortHMDI Port
H5350 Confidential 6-7
2. Process
(1) Check the COM port is "COM 2"
(Select the COM port which you are
using).
(2) Click the "Model" button.
(3) Choose the source file
"ACER_H5350 EDID-A04_USA.ini"
and then open it.
3. Process
(1) Key in the serial number into the
barcode blank space.
(2) In "Write Source Select" item,select
"Digital".
(3) Click "Program" button.
4. Process
(1) "Please change the cable to Digital"
will be shown on the screen.
(2) Please press "Ok" button.
2
3
(2)
4
(1)
(2)
(3)
(1)
(3)
H5350 Confidential 6-8
5. Finish
(1) "OK" will be shown on the screen.
6. Read EDID information
(1) In the Read item,select "Digital" and
"Trans".
(2) Please press "Read" button.
7. Read EDID information
(1) EDID Informations will show the result.
5
7
(2)
6
(2)
(1)
H5350 Confidential �
Appendix A
ASSY FAN SHIELDING MODULE WHITE H5350
Item P/N Description Parts Supply70.89T13GR01 ASSY AXIAL FAN MODULE P5270(RMA)
1 85.1F123G260 SCREW PAN MECH E/SF M3*26 Ni NO2 49.88T01G001 SUNON, KDE1207PKV1-A 70*70*20mm
AXIAL FANNO
3 43.88N01G001 THERMAL SWITCH WITH BRACKET (KLIXON YS11) 100 DEG. C
1
2
3
H5350 Confidential ��
53
ASSY LAMP DRIVER MODULE H5350
1
2
4
6
H5350 Confidential ���
Item P/N Description Parts Supply1 42.00422G001 W.A 5P 150mm LAMP DRIVER TO MB X11602 42.00443G001 CABLE W.A, 2P #20 160mm LVPS TO BALLAST 3 42.00436G001 CABLE W.A. 2P #22 100mm LAMP DRIVER TO
LAMP X1160NO
4 51.88T11G003 HOLDER LAMP DRIVER FOR H5350 NO5 51.88T18G001 KAPTON 10*10 0.05t X1160 NO6 51.89T04G001 MYLAR LAMP DRIVER H5350 NO7 51.8AQ02G001 INTERLOCK SWITCH HOLDR FOR NEC NO
70.89T15GR01 ASSY LAMP DRIVER MODULE H5350(SERVICE)8 75.88T02G001 ASSY OSRAM LAMP DRIVER O6 MIC 180W NO9 75.88T05G001 ASSY INTERRUPT SWITCH MODULE XD1130
10 85.1A126G060 SCREW PAN MECH M3*6 NO11 85.3A122G040 SCREW CAP MECH M2*4 NI NO
H5350 Confidential IV
ASSY MAIN BD MODULE H5350
13
10
H5350 Confidential V
Item P/N Description Parts Supply70.89T11GR01 PCBA MAIN BD MODULE FOR H5350(SERVICE)
1 41.82G03G001 EMI GASKET USB CONNECTOR EP719 NO70.89T12GR01 ASSY I/O COVER MODULE H5350(SERVICE)
2 41.82K11G001 EMI GASKET W6*H1*L190mm NO3 41.83F21G001 GASKET h?/W*5, H*1.5, L*15 NO4 41.88T02G001 EMI GASKET L180*W4*H1 NO5 41.89B01G001 EMI TAPE L*190/W*13 NO6 51.88T04G011 IO COVER H5350 NO7 51.88T17G001 MYLAR MB SHELDING X1160 NO8 51.89T02G001 MB SHELDING MYLAR H5350 NO9 51.89T05G001 M/B SHIELDING MYLAR FOR H5350 NO
10 51.89T06G001 M/B CNNT MYLAR H5350 NO11 52.88T06G001 SPONGE CR4305 BACK MB SHELDING X1160 NO12 61.89T01G001 MAIN-BD SHIELDING H5350 NO13 80.89T01G001 PCBA MAIN BOARD FOR H5350 NO
H5350 Confidential VI
ASSY COLOR WHEEL MODULE H5350
Item P/N Description Parts Supply70.89T09GR01 ASSY COLOR WHEEL MODULE H5350(SERVICE)
1 23.89T19G001 YO R90Y35G90C35W28B82 6 SEGMENT CW NO2 51.82Y29G001 TAPE 3M J350 10*5mm FOR COLOR WHEEL NO3 52.83615G001 COLOR WHEEL DISC RUBBER , EzPro755 NO4 61.83628G001 COLOR WHEEL SHOULDER SCREW NICKEL M2*4.8 NO5 61.88N10G001 COLOR WHEEL HOLDER SECC,X15 NO6 80.87Y04G001 PCBA PHOTO SENSOR BOARD FOR PD72807 85.1A126G040 SCREW PAN MECH M2.6*4 Ni NO
H5350 Confidential VII
ASSY HOUSING MODULE H5350
H5350 Confidential VIII
Item P/N Description Parts Supply1 41.82B01G001 EMI GASKET W13*H10.5*L30mm NO2 41.89B02G001 EMI TAPE W*20/L*70 NO3 51.81540G001 TAPE 3M J350 17*60mm NO4 51.81541G001 TAPE 3M J350 17*30mm NO
70.89T14GR01 ASSY BOTTOM COVER MODULE H5350(SERVICE)
5 51.88T02G011 BOTTOM COVER H5350 NO6 51.88T14G001 ROD DUCT X1160 NO7 51.88T21G001 MYLAR K-LOCK 0.25t X1160 NO8 51.89T02G001 MB SHELDING MYLAR H5350 NO9 51.89T03G001 LVPS MYLAR H5350 NO
10 52.86801G011 RUBBER FOOT REAR GRAY H5350 NO11 52.88T04G001 BOTTOM SHELDING AIR TIGHT X1160 NO12 61.88T03G011 SHIELDING BOTTOM COVER FOR X1260 NO13 70.89T06G001 ASSY ADJUST FOOT MODULE WHITE H5350 NO14 85.1A123G060 SCREW PAN MECH M3*6 NI NO15 86.00122G015 NUT HEX M2.0*0.4P L15 Ni NO
H5350 Confidential IX
BUY ASSY TOP COVER ADD PAINT H5350
H5350 Confidential X
Item P/N Description Parts Supply70.89T16GR01 ASSY TOP COVER MODULE
H5350(SERVICE)1 51.88T01G012 TOP COVER,PC-MN3600H,WHITE H5350 NO2 51.88T07G001 LENS POWER X1160 NO3 51.88T08G002 IR CAP,WHITE H5350 NO4 51.88T16G011 TRACK REMOTE CONTROLLER,WHITE NO5 51.88T16G031 TRACK REMOTE CONTROLLER-2,WHITE NO6 85.1A526G060 Screw Pan M2.6x6 Ni NO7 51.88T06G011 KEYPAD POWER H5350 NO
17 20 717
618
9
12
33 115
814
2411
2810
530
13
29
27
2519
2
3
26
32
H5350 Confidential XI
17 20 717
618
9
12
33 115
814
2411
2810
530
13
29
27
2519
2
3
26
32
ASSY ENGINE MODULE H5350
H5350 Confidential XII
Item P/N Description Parts Supply1 11.009F0G007 CNNT F 203P FOR 720P LGA DMD SOCKET
70.89T10GR01 ASSY ENGINE MODULE H5350(SERVICE)2 23.88N06G001 YO PLASTIC RELAY FOR X15 NO3 23.88N20G001 YO CONDENSER1 FOR X15 NO4 23.88N20G011 YO CONDENSER2 FOR X15 NO5 23.89L01G001 PROJECTION LENS YM09W NO6 41.82B01G001 EMI GASKET W13*H10.5*L30mm NO7 41.85W05G001 EMI GASKET W8*H8*L45 NO8 48.86N01G003 DMD 1280x720 PIXEL 0.62” 720P LVDS9 51.00210G001 DMD SCREW WASHER A39 NO
10 51.89B01G001 HOLDER ZOOM RING X1260 NO11 51.89B04G001 ZOOM RING X126012 51.89F02G001 DMD INSULATION PC A15 NO13 51.89T01G001 FOCUS RING H535014 52.80J01G001 DMD ANTIDUST RUBBER 739 SILICONE RUBBER NO15 52.87319G001 DMD THERMAL PAD 18*13*0.5t16 61.80J10G001 DMD LIGHT MASK 739 SUS301 NO17 61.82B36G011 SCREW M3*10.5*6 IHSPC NO18 61.88611G001 DMD SCREW Ivy10X19 61.88N12G001 ROD SPRING SUS301,X15 NO20 61.89630G001 DP759 HEATSINK SPRING NO21 61.89F01G001 DMD PLATE AL A39 NO22 61.89F02G001 ROD COVER SUS304 0.25t 1/2H HD65 NO23 61.89F04G011 DMD HEATSINK AL H5350 NO24 70.89F04G001 PRE ASSY ENGINE BASE HD65 NO25 70.89F05G001 ASSY ROD MODULE HD65 NO26 70.89F15G001 ASSY ENGINE BOTTOM COVER HD65 NO27 70.89T04G001 ASSY COLOR WHEEL MODULE H5350 NO28 85.1A526G060 SCREW PAN MECH M2.6*6 Ni NYLOK NO29 85.4A121G065 SCREW FLAT HEAD TAP M1.7*6.5 NO30 87.FL000G003 WSHR FLAT 5.0*2.4*0.3 MYLAR NO31 51.88N43G001 MYLAR FOR RELAY BOTTOM NO32 51.88N41G001 MYLAR FOR MIRROR DEAMETER 3.5mm NO33 80.89T02G001 PCBA DMD BOARD FOR H5350
H5350 Confidential XIII
ASSY BOTTOM HOUSING MODULE H5350
32
13
24
17
31
26
21
22
23
15
330
9
6
5
19
12
16
2
25
2918
27
14
1
10
118
4
20
H5350 Confidential XIV
Item P/N Description Parts Supply1 41.83F21G001 GASKET h?/W*5, H*1.5, L*15 NO2 41.85A01G001 EMI GASKET / 10*27*20 NO3 41.88T01G001 EMI ? L85*W20 NO4 49.89B01G001 SPEAKER 2W 80HM NEOSONICA DAB128 300mm 5 51.81540G001 TAPE 3M J350 17*60mm NO6 51.88T19G001 MYLAR TOP SHELDING X1160 NO7 51.88T20G001 MYLAR LENS X1160 NO8 51.89B05G001 HOLDER SPEAKER X1260 NO9 51.89T08G001 TOP SHIELDING MYLAR FOR H5350 NO
10 52.89B02G001 SPONGE ML32 SPEAKER X1260 NO11 52.89B03G001 SPONGE SRS-48P SPEAKER X1260 NO12 61.87340G001 STAND OFF M3*4L D8.0 2100MP NO13 61.88T02G001 SHELDING TOP COVET X1160 NO14 61.88T09G001 BRKT INLET X1160 NO15 61.88T15G001 ACER LOGO FOR X116016 70.86L05G001 ASSY BLOWER FAN MODULE XD1250 NO17 70.89T01G001 ASSY TWO FAN SHIELDING X1260 NO18 23.89L01G001 PROJECTION LENS YM09W NO19 70.89T03G001 ASSY MAIN BD MODULE H5350 NO20 70.89T05G001 ASSY HOUSING MODULE H5350 NO21 70.89T07G001 ASSY LAMP DRIVER MODULE H5350 NO22 75.87J01G201 ASSY LVPS MATRITEK 200W EP752(2ndu)23 75.89T01G001 ASSY FRONT COVER H535024 85.1A123G060 SCREW PAN MECH M3*6 NI NO25 85.1A126G060 SCREW PAN MECH M2.6*6 Ni NO26 85.1A326G060 SCREW PAN HEAD MECH M2.6*6 BLACK NO27 85.1C123G060 SCREW PAN MECH W/T M3*6 NI NO28 85.1C224G051 SCREW PAN MECH M4*5 COLOR W/TOOTH NO29 85.3A113G050 STEP SCREW ψ3.5xH2.5 M3x5.0mm Ni NO30 85.ZA123G040 SCREW WCH/W MECH M3*4 Ni GREEN NO31 42.00455G002 W.A. 8P TO 16P 120mm MB TO LVPS H535032 49.86E02G001 SUNON, GB1245PKV1-8 45*20mm BLOWER
H5350 Confidential XV
A.K. H5350
8
7
9
1
2
3
4
5
6
10
H5350 Confidential XVI
Item P/N Description Parts Supply1 35.82001G111 AK LABEL 3”*3” BLANK NO2 36.00006G031 WARRANTY CARD ,EUROPE FOR ACER NO3 36.00027G001 SERVICE STATION CARD NO4 36.00029G001 SECURITY CARD FOR ACER NO5 36.88T02G001 QUICK START CARD MULTILINGUAL
ACER X1160/X1260 SERIESNO
6 36.89T01G001 USER’S GUIDE MULTILINGUAL (CD) ACER H5350
NO
7 42.00232G001 CABLE COMPOSITE VIDEO 2M YELLOW NO8 42.83M08G001 CABLE VGA 1.8M 15P BLUE 2400MP NO9 45.88T02G001 REMOTE CONTROLLER X1160+ Bontech
X2(WHITE)10 51.86213G002 PE BAG ZIPPER #9 W/RECYCLING MARK
FOR OPTOMANO
H5350 Confidential XVII
D.C. H5350
6
5
3
4
1
2
7
8
9
H5350 Confidential XVIII
Item P/N Description Parts Supply1 35.89T01G001 IO MYLAR FOR H5350 NO2 35.89T02G001 LOGO MYLAR FOR H5350
70.89T17GR01 ASSY LAMP COVER MODULE H5350(SERVICE)3 51.88T05G011 LAMP COVER H5350 NO4 61.00061G001 LOCK SCREW PAN MECH M3*8.5-3.5 Ni NO5 61.88T17G001 AL FOIL FOR LAMP COVER X1160 NO
SP.88T01GC01 LAMP MODULE FOR PROJECTOR X1160/12606 70.88T02G001 ASSY LAMP MODULE X1160 NO7 70.89T02G001 ASSY BOTTOM HOUSING MODULE H5350 NO8 75.88T03G022 BUY ASSY TOP COVER ADD PAINT H5350 NO9 85.1A323G080 SCREW PAN MECH M3*8 BLACK “GREEN” NO
H5350 Confidential XIX
D.P. H5350
19
12
9
4 3
1
13
11
18
10
17
15
6
7
8
14
2
16
5
H5350 Confidential XX
Item P/N Description Parts Supply1 35.00029G001 ACER TAPE 45M FOR CARTON NO2 35.52302G091 LABEL CARTON 108*92 BLANK NO3 35.82V02G001 LABEL CARTON(SEAL) 110*50mm PD120 NO4 35.86301G001 SPEC LABEL BLANK PD120 NO5 51.00200G001 HANDLE BAR 2. PE HD70 NO6 51.00201G001 HANDLE BAR 1.PE HD70 NO9 51.52109G003 PE BAG 450*350*0.07 FOR OPTOMA NO
10 53.88T01G001 SOFT CARRY BAG X1160 NO11 55.87202GC01 BOTTOM PAPER COVER PLATE 1230*1000*4mm
3200MPNO
12 55.87W04G001 CORNER PAPER P5271 NO13 55.88T02G001 CENTER PAPER BOX X1160 NO14 55.89T01G001 CARTON CARRY BOX H5350 NO15 56.88T03G001 AIR BAG TOP X1160+ NO16 56.88T04G001 AIR BAG BOTTOM X1160+ NO17 57.00001G001 PACK SIO2 DRIER 20g NO18 58.86201GC02 WOOD PALLET 48”*40*5”(DOUBLE FACE) FOR
CPC (MATERIALl PINE)NO
19 58.86202G001 COVER PALLET 1240*1020mm FOR EzPro 736 NO20 75.88T06G002 ASSY LENS CAP X116021 AK.89T01G001 A.K. H5350 NO 22 DC.89T01G001 D.C.H5350 NO23 42.00120G011 CABLE POWER CORD 1.8M SP-023/IS-14 EU-
ROPE DIS-WARNING LABEL24 42.00110G011 CABLE POWER CORD 1.8M SP-60/IS-14 UK DIS-
WARNING LABEL25 42.00131G011 CABLE POWER CORD 1.8M SP-027/IS-14 SWIT-
ZERLAND DIS-WARNING LABEL
H5350 Confidential XXI
Appendix B I. Serial Number System Definition
Serial Number Format for Projector
00J6601000 751 00001 59 10
1 2 3 4 5
1 : 00J6601000 = Part Number excluded “dot”
2 : 751 = Week Code(ex:2007 = 7,the fifty-one weeks of the year = 51)
3 : 00001 = Serial Numbers
4 : 59 = Manufacturing Code
5 : 10 = Eng. Version Code
H5350 Confidential XXII
II. PCBA Code Definition
PCBA Code for Projector
A B XXXXXXXXXXX CC XXX EEEE
1 2 3 4 5 6
1 : ID
2 : Vendor Code
3 : P/N
4 : Revision
5 : Date Code
6 : S/N