FTI-TLK1 Type 2B2 - Vehicle Coverage & Preparation Notes
Make Model Year Install I/O Changes
DL-TL5
Scion
ToyotaToyota
ToyotaToyotaToyotaToyota
xD 80 bit STD Key
Camry 80 bit STD KeyHighlander Hybrid 80 bit STD KeyHighlander 80 bit STD KeySequoia 80 bit STD KeyTundra 80 bit STD KeyYaris Sedan 80 bit STD Key
2011-14
2010-112012-13
2011-132011-142011-172011-12
Type 2/B
Type 2/BType 2/B
Type 2/BType 2/BType 2/BType 2/B
START 2
START 2START 2START 2START 2
CAN Lights SIL Locks
Green White/BluePark / Auto
Hey! Read this stuff before you start the installation...
Firmware: Covered vehicles use BLADE-AL(DL)-TL5, flash module and update the controller firmware before installing.
Install: Type 2B vehicles use the TL5/9 main harness and TL 5/9 B CN1 adapter, using any other adapters will result in malfunctionor damage.
Lights: Type SW parking lights require connecting the green/white wire in the park/auto harnesses to pin #18 of the switch connector (pin #13 of the 13-pin connector for the Scion xD & Toyota Yaris Sedan), if equipped with auto-lights the white/red & white/blackwires in the park/auto harness are used to interrupt the wire in pin #19 for light-off control. Make no RDA connections, insulateand secure all unused connections for safety.
I/O Changes: Listed vehicles require changing the controller output from Parking Light to START, CM7x00 controllers movejumper 3 to STARTER position, CM900 controllers set feature option 1-6 to 2. If issues arise disarming the OEM alarm duringremote start, set option 1-01 to 2.
Okay, now get to work...
OBD-II
OBD-IIOBD-II
OBD-IIOBD-IIOBD-IIOBD-II
SW-13
SW-18/19SW-18/19
SW-18/19SW-18/19SW-18/19SW-13
TPMS/10TPMS/10
CM
-900
CM-900S/900AS
CM7X
00
CM7000/7200 Cut loop for A/T
CM900AS/900S Jumper
SUPPORT - 1(888) 820-3690, EXT. 203
DER
EK Z
OOLA
NDER
Est.
2001
CENT
ER
KID
S
WH
O C
AN’T
REA
D G
OO
D
AND WHO WANNA L
EARN
TO
DO
OT
HE
R S
TU
FF
GO
OD
TO
O
IIIIIIIII
I
IIIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIIIII
IIII
IIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII
for
A
B
C
D
TL 5/9 B CN1 adapter required in this installation, any other adapter will result in malfunction andpossible damage. Jumper connected to IMMO for vehicles equipped with immobilizer, if vehicle is notequipped, connect to NO IMMO before programming. IGN/GND connection required for operation.
Type 2 installs require CAN jumper to be connected to the OBD-II source connector. Secure unusedBCM connector for safety.
Covered vehicles do not use an RDA configuration for door locks, make no connection to the harnessgreen/red wire, insulate and secure the unused RDA, RDA 1, RDA 2, and RDA 3 connectors for safety.
Insert pin terminated green/white into CM I/O connector, replace (-) pk light output. Connect harnessgreen/white to wire in pin #18 of the 20-pin pk light connector (pin #13 of the 13-pin switch connectorfor the Scion xD & Toyota Yaris Sedan), if vehicle is equipped with auto-lights, interrupt wire in pin #19.
LED Programming Error CodesModule LED flashing RED during programming
1x - CAN error, confirm harness configuration2x - No IGN, confirm connections3x - No IMMO, confirm equipment and connections4x - Unknown VIN, manually assign5x - No IGN on CAN, confirm connections
123 4 5
SUPPORT - 1(888) 820-3690, EXT. 203
FTI-TLK1 Type 2B2
Module Programming ProcedureStep 1 - Activate IGN, LED will turn solid redStep 2 - Wait for Solid green LEDStep 3 - Programming complete
FTI-TLK1 Type 2B2 - Installation Notes & Wiring Diagram
BLADE
1
16
RDA
3
RDA
2
RDA
1
RDA
AUTO LT. B
AUTO LT. A
PARK LT. A
IMMO NO IMMO
81 11180201 1
IGN/GND
PK L
IGHT
OUTP
UT
19
PARK/AUTO LT
18
19
61
7
30
1
1
COLORS VARY
1
2
3
4Parking Light Switch
Main Body ECU
Ignition Switch
OBD-II ConnectorA
B
C D
D
D
*Interrupt wire in pin #19only if equipped withAuto-lights (Camry,
Highlander, Sequoia,and Tundra)
1453113
Scion xD & Toyota Yaris Sedan
6
12 10 7
blue
TPMS Module
TPMS
* Sequoia & Tundra SIL Interrupt
5
TL5/9 CAN
BCM CANOBD II CAN
OBD II
BCM
TL5/9 B
Top Related