8/10/2019 Final Project Ppt uppcl
1/19
PRESENTED BY:
ADITI MISHRA (1105421007) DIVYA PANDEY (1105421041) AMBUJ TIWARI (1105421013) KARTIK DUBEY (1105421054)
HEAD OF THE DEPARTMENT PROJECT CO-ORDINATOR
MR. ANIL SINGH RATHORE MR. ABHISHEK SRIVASTAV( ASSISTANCE PROFESSOR )
8/10/2019 Final Project Ppt uppcl
2/19
INTRODUCTION
The aim of this project is four quadrant speed control of DCmotor .
Motor is operated in four quadrant i.e; clockwise , counterclockwise, instantaneous forward brake and instantaneousreverse brake.
Speed of DC motor is directly proportional to the DCvoltage across its terminals .
Speed of DC motor is controlled by controlling DC voltageand by pulse width modulation.
8/10/2019 Final Project Ppt uppcl
3/19
MAIN COMPONENTS
1. Micro switch
2. Microcontroller
3. Motor driver
4. DC motor
5. Step down transformer
6. Bridge rectifier
8/10/2019 Final Project Ppt uppcl
4/19
COMPONENTS DISCRIPTION
MICROSWITCH: A micro switch, also know as snap-actionswitch is a generic term used to refer to an electric switch.
MICROCONTROLLER: The microcontroller used here is acommon 8-bit Atmel microcontroller.
MOTOR DRIVER: It receives signals from the microcontrollerand on the basis of that it will drive the motors.
DC MOTOR: A DC motor is simple electric motor that useselectricity and magnetic field to produce torque, which turnsthe motor.
8/10/2019 Final Project Ppt uppcl
5/19
PRINCIPLE OF OPERATION
Speed control of DC motor can be done by various ways:
Direction of the motor can be controlled by controlling the
polarity of current flowing through it. Speed of motor is controlled by DC voltage applied across its
terminals.
PWM wave can be used to control the speed of DC motor.
8/10/2019 Final Project Ppt uppcl
6/19
Speed
Torqe
IaRa
Ea
Va
IaRa
Ea
Va
IaRa
Ea
Va
IaRa
Ea
Va
Va < Ea Va > Ea
Va > Ea Va < Ea
Forward Breaking Forward Motoring
Reverse Motoring Reverse Breaking
FOUR QUADRANT OPERATION
8/10/2019 Final Project Ppt uppcl
7/19
BLOCK DIAGRAM
8/10/2019 Final Project Ppt uppcl
8/19
MICROSWITCH
A micro switch, also known as snap-action-switch, is ageneric term used to refer to an electric switch.
They are very common due to their low cost and durability,greater than one million cycles and up to 10 million cycles forheavy duty models.
Common application of micro switches include the doorinterlock on a microwave oven, levelling and safety switches
in elevators, vending machines and to detect paper jams orother faults in photocopiers.
8/10/2019 Final Project Ppt uppcl
9/19
RAM ROM
I/O
PortTimer
Serial
COM
Port
Microcontroller
CPU
A single chip
MICRO CONTROLLER USED
The microcontroller used here is a common Atmelmicrocontroller.
It is a low power, high performance CMOS 8 bitmicrocontroller.
8/10/2019 Final Project Ppt uppcl
10/19
PIN DIAGRAM
2K bytes EEPROM Data Memory.
2.7v to 5.5v Operating Range.
256x8 bit Internal RAM.
32 programmable I/O lines.
Three 16-bit Timer/Counters.
Nine interrupt sources.
8/10/2019 Final Project Ppt uppcl
11/19
ATMEL PIN DIAGRAM
8/10/2019 Final Project Ppt uppcl
12/19
MOTOR DRIVER
H-bridge is an electronic circuit which enables a voltage to beapplied across a load in either direction.
These circuits are often used in robotics and other application to
allow DC motors to run forwards and backwards.The motor operating switch:
The motor operationA B C D
Forward motoring
Reverse motoring
Reverse Breaking
Forward Breaking
1 0 0 1
0 0 1 0
0 1 1 0
0 0 0 1
Vcc
Q1
Q4
Q3
Q2G
G
G
GA B
C D
ON
OFF
OFF
ON
M
D1
D4
D3
D2
8/10/2019 Final Project Ppt uppcl
13/19
PULSE WIDTH MODULATION
Different types of waves:
sine, square, sawtooth, triangle.
PWM uses square waves.
Discrete On/Off values.
Based on duty cycles;
On and Off time
8/10/2019 Final Project Ppt uppcl
14/19
ADVANTAGES
It is user friendly.
Safer to use. Reduces the tome of switching due to automation.
Requires least maintenance.
Can be used in rotor controls.
8/10/2019 Final Project Ppt uppcl
15/19
APPLICATIONS
ROBOTIC CONTROLS.
SWING MACHINES.
ELECTRONIC BIKES.
WINDING MACHINES.
DC OPERATED DRILL MACHINES.
CNC MACHINES.
MOBILE AIR CONDITION FANS.
TOYS.
ELCTRONIC DOOR CONTROLLERS.
ELECTRONIC CHAIRS(beauty parlor etc.)
8/10/2019 Final Project Ppt uppcl
16/19
CIRCUIT OVERVIEW
CIRCUIT OVERVIEW
8/10/2019 Final Project Ppt uppcl
17/19
CONCLUSION
We have achieved the required speed And also we displaythis on LCD display.
Our aim of this project, we have achieved the speed controlof DC motor.
8/10/2019 Final Project Ppt uppcl
18/19
THANK YOU
8/10/2019 Final Project Ppt uppcl
19/19
QUERIES ?