US90A/US91A Datasheet
REVISION 06 – 20 JUL 2017
1. Features and Benefits
Integrated High sensitivity Hall Sensor
No VDD concept
Locked rotor protection and auto-restart
Power-efficient CMOS and power MOSFETs
Built-in output protection clamping diode
Integrated tachometer (FG: US90A) or alarm (RD: US91A) signal output
FG/RD SIP package options:
4 pins VA and VK package
SMD package options
SOIC8 bent leads
SOT25 straight leads
RoHS Compliant
Peak current up to 500mA
2. Application Examples
12V and 24V 2-coil fans
3. Description
The US90A/91A is a one-chip solution for driving two-coil brushless DC cooling fans. Based on the advanced Melexis CMOS process, the IC contains a Hall-effect sensor, dynamic offset correction and low side output drivers. Frequency Generator or Rotation Detection is available. The open-drain output makes the connectivity with any external interface such as hardware monitoring or Super I/O IC easier. These features are combined with the Melexis patented no-VDD design to fit the IC in small 4-pin VK and VA package. The device is also delivered in DC package for automatic assembly.
Figure 1
US90A/US91A Datasheet
Page 2 of 16
REVISION 006 – 20 JUL 2017
Contents
1. Features and Benefits ............................................................................................................................ 1
2. Application Examples ............................................................................................................................. 1
3. Description ............................................................................................................................................ 1
4. Ordering Information ............................................................................................................................ 3
5. Glossary of Terms .................................................................................................................................. 4
6. Pin Definitions and Descriptions ............................................................................................................ 4
7. Electrical Specifications ......................................................................................................................... 5
7.1. Absolute Maximum Ratings ............................................................................................................... 5
7.2. General Electrical Specifications ........................................................................................................ 5
7.3. Magnetic Specifications ...................................................................................................................... 6
7.4. Driver output vs Magnetic pole ......................................................................................................... 6
8. Description ............................................................................................................................................ 7
8.1. General description ............................................................................................................................ 7
8.2. No-VDD concept ................................................................................................................................. 7
8.3. LRP ....................................................................................................................................................... 7
9. Performance Graphs.............................................................................................................................. 8
10. Application Information ....................................................................................................................... 9
11. Package Information .......................................................................................................................... 10
11.1. VK Package Information (4-pin TO92) ........................................................................................... 10
11.2. Trimmed VK T&R(dead bug) : VKAAA000-RX ............................................................................... 10
11.2.1. VKAA000-RX Tape ..................................................................................................................... 11
11.2.2. VKAAA000-RX Lead Trim length ............................................................................................... 11
11.3. DC Package Information (8-pin narrow SOIC) ............................................................................... 11
11.4. VA Package Information (4-pin TO92 flat) ..................................................................................... 12
11.5. ZE Package (SOT25 with straight leads) ......................................................................................... 14
12. Standard Information ........................................................................................................................ 14
13. ESD Precautions ................................................................................................................................. 15
14. Disclaimer .......................................................................................................................................... 15
15. Revision History Table ....................................................................................................................... 16
16. Contact .............................................................................................................................................. 16
US90A/US91A Datasheet
Page 3 of 16
REVISION 006 – 20 JUL 2017
4. Ordering Information
Product Temperature Package Option Code
Packing Form
Description
US90A E DC AAA-000 RX FG (frequency output)
US91A E DC AAA-000 RX RD (alarm output)
US90A E VK AAA-000 BU FG (frequency output)
US90A E VK AAA-000 RX VK cut leads in T&R
FG (frequency output)
US91A E VK AAA-000 BU RD (alarm output)
US91A E VK AAA-000 RX VK cut leads in T&R
RD (alarm output)
US90A E VA AAA-000 BU FG (frequency output)
US91A E VA AAA-000 BU RD (alarm output)
US90A E ZE AAA-000 RE FG (frequency output)
US91A E ZE AAA-000 RE RD (alarm output)
Legend:
Package Code: “DC” for SOIC-8 package
“VK” for Plastic Single in Line thickness 1.5 - 1.6mm
“VA” for Plastic Single in Line thickness 1.1 -1.2mm
“ZE” for straight leads SOT25
Packing Form: “RE for Reel, live bug (die face up)”
“RX for Reel, dead bug (die face down)”
“BU for Bulk bag”
Ordering Example: “US91AEZE AAA000-RE” For an RD output in straight leads SOT25 package, delivered in Reel.
Table 1
US90A/US91A Datasheet
Page 4 of 16
REVISION 006 – 20 JUL 2017
5. Glossary of Terms
Gauss (G), Tesla (T) Units for the magnetic flux density 1 mT = 10 G
NC Not Connected
Two-coil fan A fan with two-coil windings where current alternates from 1 coil to the other depending on the direction of the magnetic field.
MilliTesla (mT), Gauss Units of magnetic flux density: 1mT = 10 Gauss
VDD Voltage on the coils common node.
IDD Current supplying the chip which flows through the coil connected to the switched off output driver.
Peak output current The current flowing in the coil at start-up, only limited by the coil resistance RCOIL and the output driver resistance RDSON.
Continuous output current The current flowing in the coil when the fan is spinning normally
Locked rotor The state when the fan stopped spinning due to mechanical blockage.
FG Frequency generator or tachometer output
RD Rotation detection or alarm output
LFPM Linear Feet Per Minute – Unit of airflow velocity
Table 2
6. Pin Definitions and Descriptions
Name SOIC8
Pin #
SOT25
Pin #
VK
Pin #
VA
Pin #
Description
FG (RD) 1 4 1 1 open drain output signal
OUT1 2 3 2 2 Open Drain Coil Driver 1
OUT2 3 1 3 4 Open Drain Coil Driver 2
GND 4 2 4 3 Ground pin
N.C. 5,6,7,8 5 Not Connected
Table 3
US90A/US91A Datasheet
Page 5 of 16
REVISION 006 – 20 JUL 2017
For optimal EMC behavior connect the unused pins (Not Used) to the Ground.
7. Electrical Specifications
7.1. Absolute Maximum Ratings
Parameter Symbol Value Units
Fan Supply Voltage VDD 30 V
Maximum voltage OUT1, OUT2 Vout 100 V
Peak Output Current IOUTp 500 mA
Continuous Output Current IOUTc 250 mA
FG / RD Output Current IFG (RD) 20 mA
Junction Temperature TJ -40 to 125 °C
Storage Temperature Range TS -55 to 150 °C
Magnetic Flux Density B Unlimited mT
ESD HBM ESDhbm 4000 V
Table 4
Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute maximum-rated conditions for extended periods may affect device reliability.
7.2. General Electrical Specifications
DC Operating Parameters TA = 25o
C, VDD = 24V (unless otherwise specified)
Parameter Symbol Test Conditions Min Typ Max Units
Fan Supply Voltage VDD Operating, RCOIL = 50Ω 4.7(1) 30 V
Supply Current IDD 2 4 mA
Output Saturation Voltage VDSON IOUT = 150mA 375 mV
Output Saturation Voltage VDSON IOUT = 250mA 625 mV
Output Clamp Voltage VOUT 60 80 V
FG / RD Output Low Voltage VOL IOL = 10mA 250 500 mV
FG / RD Output Clamp Voltage VCLAMP 28 V
US90A/US91A Datasheet
Page 6 of 16
REVISION 006 – 20 JUL 2017
Parameter Symbol Test Conditions Min Typ Max Units
FG / RD Output Leakage Current
ILEAK VFG (VRD) = 18V
10 uA
Locked rotor ON time Ton 210 350 ms
Locke rotor OFF time Toff Auto restart after locked rotor shut down
6.3*Ton
DC Thermal Resistance RTHja (2) 150 °C/Watt
VK Thermal Resistance RTHja (2) 200 °C/Watt
VA Thermal Resistance RTHja (2) 170 °C/Watt
ZE Thermal Resistance RTHja (2) 170 °C/Watt
ZE Thermal Resistance RTHjc Junction to package top 20 °C/Watt
Table 5 Note 1: The minimal value of VDD should be determined using the following equation: VDD = 4.5V + RCOIL * IDD
Note 2: Rthja for JEDEC single layer board 76.2 x 114.3 x 1.60, zero LFPM
7.3. Magnetic Specifications
DC Operating Parameters TA = 25o
C, VDD = 24V (unless otherwise specified)
Parameter Symbol Test Conditions Min Typ Max Units
Operate point BOP 3 6 mT
Release point BRP 6 3 mT
Hysteresis BHYST 2 6 mT
Table 6 magnetic specification
7.4. Driver output vs Magnetic pole
Parameter Test Conditions OUT1 OUT2
North pole B < Brp – all packages High Low
South pole B > Bop all packages Low High
Table 7: Driver output vs. mangetic pole Note: The magnetic pole is applied facing the branded side of the package
US90A/US91A Datasheet
Page 7 of 16
REVISION 006 – 20 JUL 2017
8. Description
8.1. General description
The US90A/91A is a one-chip solution for driving two-coil brushless DC fans. Based on advanced Melexis CMOS process, the
IC contains a Hall-effect sensor, dynamic offset correction and low side output drivers.
The output drivers OUT1 and OUT2 are fully protected against switching transients. So there is no need for an external zener
diode to cut the high voltage spikes induced by the fan coils.
The US90A has an open-drain integrated tachometer FG output that follows the Hall signal. In the US91A, the open-drain
rotation detection output RD is active low during normal spinning of the motor. It goes high when the flux switching frequency
becomes too low, which means the motor is blocked.
8.2. No-VDD concept
The absence of a VDD pin enables the two low side output drivers and FG/RD signal output to fit in a four-pin VK package. The
lack of a VDD pin decreases also the probability to damage the chip due to reverse voltage connection, using the coil resistance
to limit the reverse current. In this condition, the total reverse current is twice the peak current value of the fan used.
8.3. LRP
The built-in locked-rotor protection will automatically shut off the coil current when the rotor is mechanically blocked, or the
rotational speed drops below 60 RPM (4-pole rotor magnet). The fan will try to restart every
1.5 seconds until the obstruction is clear. The On / Off cycling reduces the average stall current to 1/7 normal; this is enough to
prevent overheating or damage to most fans. Both the US90A and US91A have this feature.
US90A/US91A Datasheet
Page 8 of 16
REVISION 006 – 20 JUL 2017
9. Performance Graphs
11.1 RDSON vs TJ 11.2 RDSON vs VDD
11.3 Magnetic parameters vs TJ 11.4 Magnetic parameters vs VDD
11.5 IDD vs TJ 11.6 IDD vs VDD
11.7 VOL vs TJ 11.8 Power Dissipation vs. TA
US90A/US91A Datasheet
Page 9 of 16
REVISION 006 – 20 JUL 2017
10. Application Information
Typical application with pull-up resistor Configuration for reverse voltage protection
The left schematic shows an application including several external protections.
The diode DREVPROT best protects the chip and fan coils for reverse voltage condition. The no-VDD design enables ESD protection at fan module level to be easily improved. The fan coils prevent and filter fast current stress on OUT1 and OUT2, resulting in better ESD protection.
US90A/US91A Datasheet
Page 10 of 16
REVISION 006 – 20 JUL 2017
11. Package Information
11.1. VK Package Information (4-pin TO92)
11.2. Trimmed VK T&R(dead bug) : VKAAA000-RX
US90A/US91A Datasheet
Page 11 of 16
REVISION 006 – 20 JUL 2017
11.2.1. VKAA000-RX Tape
Die is face down. Top Marking is face down in the tape:
11.2.2. VKAAA000-RX Lead Trim length
11.3. DC Package Information (8-pin narrow SOIC)
US90A/US91A Datasheet
Page 12 of 16
REVISION 006 – 20 JUL 2017
11.4. VA Package Information (4-pin TO92 flat)
US90A/US91A Datasheet
Page 13 of 16
REVISION 006 – 20 JUL 2017
US90A/US91A Datasheet
Page 14 of 16
REVISION 006 – 20 JUL 2017
11.5. ZE Package (SOT25 with straight leads)
Top marking US91A, US90A
12. Standard Information
0.27
0.04
0.07
| 9 0 Y Y
|WW X X X
5 4
1 2 3
OUT2 GND OUT1
NC FG
| 9 1 Y Y
|WW X X X
5 4
1 2 3
OUT2 GND OUT1
NC RD
US90A/US91A Datasheet
Page 15 of 16
REVISION 006 – 20 JUL 2017
Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity level according to standards in place in Semiconductor industry.
For further details about test method references and for compliance verification of selected soldering method for product integration, Melexis recommends reviewing on our web site the General Guidelines soldering recommendation. For all soldering technologies deviating from the one mentioned in above document (regarding peak temperature, temperature gradient, temperature profile etc), additional classification and qualification tests have to be agreed upon with Melexis.
For package technology embedding trim and form post-delivery capability, Melexis recommends to consult the dedicated trim&form recommendation application note: lead trimming and forming recommendations
Melexis is contributing to global environmental conservation by promoting lead free solutions. For more information on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of the use of certain Hazardous Substances) please visit the quality page on our website: http://www.melexis.com/en/quality-environment
13. ESD Precautions
Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products.
14. Disclaimer
The information furnished by Melexis herein is believed to be correct and accurate. Melexis disclaims (i) any and all
liability in connection with or arising out of the furnishing, performance or use of the technical data or use of the
product as described herein, (ii) any and all liability, including without limitation, special, consequential or incidental
damages, and (iii) any and all warranties, express, statutory, implied, or by description, including warranties of fitness
for particular purpose, non-infringement and merchantability. No obligation or liability shall arise or flow out of
Melexis’ rendering of technical or other services.
The information contained herein is provided "as is” and Melexis reserves the right to change specifications and/or
any other information contained herein at any time and without notice. Therefore, before placing orders and/or prior
to designing this product into a system, users or any third party should obtain the latest version of the relevant
information to verify that the information being relied upon is current. This document supersedes and replaces all
prior information regarding the product(s) as described herein and/or previous versions of this document.
Users or any third party must further determine the suitability of the Melexis’ product(s) described herein for its
application, including the level of reliability required and determine whether it is fit for a particular purpose.
The information contained herein is proprietary and/or confidential information of Melexis. The information contained
herein or any use thereof does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other
intellectual property rights, whether with regard to such information itself or anything described by such information.
This document as well as the product(s) described herein may be subject to export control regulations. Please be
aware that export might require a prior authorization from competent authorities.
The product(s) as described herein is/are intended for use in normal commercial applications. Unless otherwise agreed
upon in writing, the product(s) described herein are not designed, authorized or warranted to be suitable in
applications requiring extended temperature range, unusual environmental requirements. High reliability
applications, such as medical life-support or life-sustaining equipment are specifically not recommended by Melexis.
US90A/US91A Datasheet
Page 16 of 16
REVISION 006 – 20 JUL 2017
The product(s) may not be used for the following applications subject to export control regulations: the development,
production, processing, operation, maintenance, storage, recognition or proliferation of 1) chemical, biological or
nuclear weapons, or for the development, production, maintenance or storage of missiles for such weapons: 2) civil
firearms, including spare parts or ammunition for such arms; 3) defense related products, or other material for
military use or for law enforcement; 4) any applications that, alone or in combination with other goods, substances or
organisms could cause serious harm to persons or goods and that can be used as a means of violence in an armed
conflict or any similar violent situation.
Products sold by Melexis are subject to the terms and conditions as specified in the Terms of Sale, which can be found
at https://www.melexis.com/en/legal/terms-and-conditions.
Melexis NV © - No part of this document may be reproduced without the prior written consent of Melexis. (2016)
ISO/TS 16949 and ISO14001 Certified
15. Revision History Table
006
Added US91AEVK-AAA000-RX options
Added Ton/Toff specification.
Added SOT straight leads package: 11.5ZE Package (SOT25 with straight leads)
Added marking info VA, VK
Added ESD hbm rating
Corrected characterization graphs for RDSon
Table 8
16. Contact
For the latest version of this document, go to our website at www.melexis.com. For additional information, please contact our Direct Sales team and get help for your specific needs:
Europe, Africa Telephone: +32 13 67 04 95
Email : [email protected]
Americas Telephone: +1 603 223 2362
Email : [email protected]
Asia Email : [email protected]
Top Related