EMS1EP Lecture 8Pulse Width Modulation (PWM)
Dr. Robert Ross
Overview (what you should learn today)
• Analog v’s digital• Theory behind PWM• PWM sample circuit/Demo• Worked examples• Servo Control
Digital Revision – Analog/Digital
• Analog Voltages: Continuous in time and value• Digital Voltages: Discrete in time and value
Analog/Digital
• The real world is analog• Most things we measure or control can be
described my continuous values– Pressure, temperature, acceleration, sound, light
• Computers are digital• Need to convert these analog voltages as
digital values
Analog/Digital
Microcontroller(LArduino)
ADCAnalog
to Digital
Converter
DACDigital
to Analog
Converter
Transducer(Sensor) Actuator
Physical Variable
(Sound, light, pressure, temp, ect)
Control Physical Variable
(Sound, light, pressure, temp, ect)
Analog Voltages
Digital Voltages
ADC and DAC
• Analog to Digital Converters (ADCs) are used to convert the analog voltages into a digital value
• Digital to Analog Converters (DACs) are used to generate analog voltages using digital values
• The LArduino board has internal ADCs and has pins which can be configured as analog outputs using Pulse Width Modulation
Quantisation
• The analog values produced by a DAC look analog but are actually quantised values (not continuous)
• These values are in small steps• The LArduino has 256 steps (0-255) over the range 0-
5V• 19.6mV Steps (5V/255=0.0196)• To improve resolution:
– Lower the voltage range (0-3V)– Increase the number of bits:
• 8Bits = 255 Steps• 16Bits = 65535 Steps
PWM Characteristics
• Create a square-wave• Constant period• Varying duty cycle (proportional to required
analog voltage)
5V
0V
Generating Analog Voltages5V
0V
analogWrite(pin, 0); 0% Duty cycle - Average Voltage: 0V
5V
0V
analogWrite(pin, 255); 100% Duty cycle - Average Voltage: 5V
5V
0V
analogWrite(pin, 63); 25% Duty cycle - Average Voltage: 1.25V
5V
0V
analogWrite(pin, 127); 50% Duty cycle - Average Voltage: 2.5V
5V
0V
analogWrite(pin, 191); 75% Duty cycle - Average Voltage: 3.75V
Filtering PWM Signal
Without filtering circuitry With filtering circuitry:
Pulse Width Modulation (PWM)
• Use: – analogWrite(pin, <AnalogVoltage>);– AnalogVoltage can vary from 0-255
• Will toggle the pin really fast high and low – to produce something more like an analog voltage need to smooth this out
• Use a Low Pass Filter to smooth the voltage out to approximate an analog voltage
PWM Applications
• Communication – length of pulse specifies 1’s and 0’s
• Voltage Regulation• LED brightness control• Controlling the speed of motors• Servo control
PWM on the LArduino
• PWM can be performed on any of the pins marked with a ‘P’
• Use pins 5, 6, 9, 10, 11
• Pins used for PWM don’t need to be setup – analogWrite does this automatically
Class Challenge
• Write some code to do the following:– A switch is connected to Pin 8– A LED is connected to Pin 6
• If the button is pressed the LED should be at 75% brightness
• If the button is not pressed the LED should be at 25% brightness
Worked example – Sawtooth signal
• Create a sawtooth signal on Pin 5• When connected to an LED the LED should
successively fade brighter and dimmer• When connected to a scope should give
output (when connected to filter):
Sawtooth - Codeint PWMOUT1 = 5; // PIN ASSIGNMENTSvoid setup() { //PWM pins don't require initialisation}void loop() { int onTime = 0; while(onTime < 255){ onTime++; analogWrite(PWMOUT1, onTime); delay(10); } while(onTime > 0){ onTime--; analogWrite(PWMOUT1, onTime); delay(10); }}
Sawtooth - Results
No Filtering (Value increased and then decreased)LED connected – goes brighter then dimmer
Servo Control
• Remote control aircraft (and some robotics) are operated using servos
Servo Control
• Servos need to be attached to pin 9 or 10 on the LArduino board
• Servos are controlled using a PWM signal– Period: 20ms– On time: 1.25 to 1.75ms– On time sets the position of the servo arm
Servo Control: Hardware connections
Arduino 5V
Red – Power (4-6V)
Black (or Brown) – GND
Yellow (or White or Orange) – PWM signal pin
Servo Worked Example
• If button on Pin 5 is pressed servo to go to 30O
• If button is not pressed servo to go to 120O
• Servo connected to Pin 9
• Using Arduino Servo library– Allows desired angle of servo to be specified
Servo Worked Example#include <Servo.h>
Servo servo1; // create servo object to control a servoint button1 = 5;void setup(){
servo1.attach(9); // Servo on Pin 9pinMode(button1, INPUT);
}
void loop(){
if (digitalRead(button1) == LOW){ //Button pressedservo1.write(30);
}else{ //Button not pressed
servo1.write(120);}
}
Continuous Rotation Servos
• By default servo motors only have about 180O of motion that they can travel over
• Servos can be modified for continuous rotation (they can go right around)
• PWM signal controls speed not position of continuous rotation servos
• Involves:– Removing feedback potentiometer (variable resistor)– Soldering in resistors– Cutting notch out of gears
Summary(What you learnt in this session)
• The real world is analog, but our microcontrollers are digital
• PWM is one type of DAC to generate analog like voltages from a microcontroller
• Use analogWrite() to set PWM value• Servos use PWM to set the position of the
servo arm – can use the servo library
Top Related