2
The Bridges Electric™ type SE and type SEL line tension disconnects are ruggedly built, reliable devices that splice right onto the line, safely supporting the conductor while providing the required insulation gap for quick and safe line maintenance. The switches offer these advantages:
n Classic solid porcelain electrical insulation with no porcelain in tension
n Multiple insulator units per switch for maximum safety
n Lightweight design minimizes conductor loading – may be used with smaller conductors
n Slim 4 1/4” diameter insulator profile – easier to cover for hot line work
n Rigid square tubular blade and high-pressure coin silver contacts
n Loadbreak hooks available
n Loadbreak versions available
n Quick break versions available
n Closer arm versions available.
The Bridges Electric™ line tension disconnect
3
taking advantage of relatively high compres-sion strength, and avoids sheer and tension stresses, which porcelain does not handle exceptionally well. Another benefit of this classic design is the complete enclosure of the stressed porcelain within a solid metal housing, which is the “cap” of the strain insu-lator. The insulator assemblies for the Bridges Electric type SE and type SEL series of line tension switches are manufactured from high-strength, chip-resistant, alumina porcelain shells. A one-piece cast cap, a forged steel pin and premium zero-shrink grout complete the assembly of the insulator units. A precision assembly jig ensures dimensional and mechanical consistency.
A line tension switch, by the nature of its application, must mechanically support the line and provide high-voltage electrical insulation when the switch is in the open position. Almost since the inception of the electrical power industry, the most depend-able means of providing these two basic functions has been the porcelain strain insu-lator. This classic design approach imposes primarily compressive stresses in the porce-lain shell when the unit is subjected to tensile loads. The conversion of tensile forces to compressive stress comes about through inclusion of properly placed angular surfaces. The metallic surfaces involved are coated with a thin, resilient coating that allows a slight amount of relative movement producing a wedging action. This action places the porcelain in a compressive load,
The Bridges Electric™ strain insulator assembly
During and after assembly,
rigorous quality control and
tensile proof tests ensure
that this is a strain insulator
worthy of a Bridges Electric
type SE or type SEL line
tension switch.
High Strength Alumina Porcelain
One-Piece Cap
3/4-10 Threads
Resilient Coating
Forged Steel Pin
Tensile Forces
Compressive Forces
4
n 180° blade catch is standard on catalog number 395
n Available as an option on all other catalog numbers with loadbreak hooks
The Bridges Electric™ type SE with loadbreak hooks
For use with a loadbreak tool
327-01
395
195127
5
n Tensile tested: 7,500 lbs.
n Ultimate tensile: 15,000 lbs.
The Bridges Electric™ type SE with loadbreak hooks
For use with a loadbreak tool
600 ACatalog number Max. kV kV BIL Net weight
127 25 150 17 lb.327 38 200 22 lb.
900 ACatalog number Max. kV kV BIL Net weight
129 25 150 18 lb.329 38 200 23 lb.
1,200 ACatalog number Max. kV kV BIL Net weight
195 25 150 20 lb.395 38 200 26 lb.
127-129 195
327-329 395
6
The Bridges Electric™ type SE non-loadbreak
190
390
1,200 ACatalog number Max. kV kV BIL Net weight
190 25 150 20 lb.390 38 200 26 lb.
For use where a loadbreak provision is not required
n Tensile tested: 7,500 lbs.
n Ultimate tensile: 15,000 lbs.
n 180° blade catch is standard on catalog number 390
n Available as an option on catalog number 190
390
190
7
The Bridges Electric™ type SE with quick break
All the quality of a standard switch, but with a quick-break device
n The quick-break option is applicable to all distribution class hookstick disconnects
n Add “QB” as a suffix to the catalog number (for example: 127QB)
n 180° blade catch is standard on all 200 kV BIL quick-break switches
n All other dimensions and ratings are the same as the standard switch equivalent
327QB
190QB
8
The Bridges Electric™ type SEL with Saf-T-Gap interrupter
120
340
600 ACatalog number Max. kV kV BIL Net weight
120 25 150 20 lb.340 38 200 32 lb.
The type SEL offers all the benefits of the standard type SE switches plus the same high quality Saf-T-Gap expulsion interrupter. The Saf-T-Gap interrupter changes in seconds with a standard shotgun-style hookstick.
n 180° blade catch is standard on catalog number 340
n Available as an option on catalog number 120
n Tensile tested: 5,000 lbs.
n Ultimate tensile: 10,000 lbs.
340
120
9
The Bridges Electric™ line tension disconnect with closer arm
Pull the switch to open via the pull ring…
Pull the switch to close via the closer arm…
The closer arm option allows for installa-tion of the switch farther away from the crossarm and is applicable to most type SE and type SEL switches
n Not compatible with switches having a 180° blade catch
n Add the letter “V” as a suffix to the catalog number (for example: 127 V)
n Retrofit kit available to retrofit existing type SE and type SEL switches
10
The Bridges Electric™ line tension disconnectaccessories
Stabilink clamping stabilizern Mounts to any tie-top insulatorn Completely adjustable
Extension linksn End fittings may be rotated and re-tightened
Cable connectorn Hot tin-dipped red brass with stainless steel hardwaren Fits any 1.75” terminaln Conductor ranges n #6 – 397.5 MCM ACSR n #4 – 500 MCM copper
Trunnion linksn End fittings may be rotated and re-tightened
2094 Clevis-Clevis
2092 Eye-Clevis
2090
2090-01
2099-24
2099-14
2438
UV Vinyl Coating
11
The Bridges Electric™ line tap disconnect
The Bridges Electric type LER line tap disconnect is a rugged and reliable disconnect device that may be used either in tension or clamped onto the line for a wide array of cable-riser and crossover applications.
These switches feature a sturdy and well-ventilated square tubular copper blade and high-pressure silver contacts for superior current carrying characteristics.
In addition to a positive latch, all switches come with an exclusive opening mecha-nism to ease hookstick operation even after years in service.
Many available options, accessories and mounting configurations make the type LER a flexible solution to any overhead line tap application where dependable operation in a lightweight package is required.
12
The Bridges Electric™ type LER with loadbreak hooks
600 ADimensions - inches
Catalog number
Max. kV
kV BIL
A B C D Net weight*
LER264 15 110 8 9.9 18.5 10.5 19 lbs.LER364 25 150 10 11.6 25 14.8 21 lbs.LER464 38 150 10 11.6 25 14.8 21 lbs.
* Weight reflects porcelain insulators.Polymer insulators available.
900 ADimensions - inches
Catalog number
Max. kV
kV BIL
A B C D Net weight*
LER294 15 110 8 9.9 18.5 10.5 21 lbs.LER394 25 150 10 11.6 25 14.8 23 lbs.LER494 38 150 10 11.6 25 14.8 23 lbs.
* Weight reflects porcelain insulators.Polymer insulators available.
For use with a loadbreak tool
13
600 ADimensions - inches
Catalog number
Max. kV
kV BIL
A B C D Net weight*
LER265 15 110 8 9.9 18.5 11.1 23 lbs.LER365 25 150 10 11.6 23 15.3 25 lbs.
The Bridges Electric™ type LER with Saf-T-Gap interrupter
* Weight reflects porcelain insulators.Polymer insulators available.
900 ADimensions - inches
Catalog number
Max. kV
kV BIL
A B C D Net weight*
LER295 15 110 8 9.9 18.5 11.1 24 lbs.LER395 25 150 10 11.6 23 15.3 26 lbs.
* Weight reflects porcelain insulators.Polymer insulators available.
The type LER offers all the benefits of the standard type LER switches plus the same high quality Saf-T-Gap expulsion interrupter. The Saf-T-Gap interrupter changes in seconds with a standard shotgun-style hookstick.
14
600 ADimensions - inches
Catalog number
Max. kV
kV BIL
A B C D Net weight*
LER267 15 110 8 9.9 18.5 10.5 19 lbs.LER367 25 150 10 11.6 25 14.8 21 lbs.LER467 38 150 10 11.6 25 14.8 21 lbs.
* Weight reflects porcelain insulators.Polymer insulators available.
900 ADimensions - inches
Catalog number
Max. kV
kV BIL
A B C D Net weight*
LER297 15 110 8 9.9 18.5 10.5 21 lbs.LER397 25 150 10 11.6 25 14.8 23 lbs.LER497 38 150 10 11.6 25 14.8 23 lbs.
* Weight reflects porcelain insulators.Polymer insulators available.
The Bridges Electric™ type LER non-loadbreak
For use where a loadbreak provision is not required
15
The Bridges Electric™ line tap disconnect options/accessories
C = Captive terminal hardware
K = 1/2” rodsL = 5/8” rodsM = 3/4” rods
P = Polymer insulatorLine tap disconnectinstalled with hangers
Universal base designed tobe used with 3/4” or 1”hangers or cable connectors
W = 1/2” hangersY = 3/4” hangersZ = 1” hangers
Line tap disconnectinstalled with cable connectors
2088 3/4” hanger kit
2088-02 1” hanger kit
Line tap disconnectinstalled in tension
16
The Bridges Electric™ type SER single insulator disconnect
The Bridges Electric type SER single insu-lator disconnect is a rugged and reliable disconnect where dependable operation in a lightweight package is required.
These switches feature a sturdy and well-ventilated square tubular copper blade and high-pressure silver contacts for superior current carrying characteristics. In addition to a positive latch, all switches come with an exclusive opening mecha-nism to ease hookstick operation, even after years of service.
Many available options, accessories and mounting configurations make the type SER a flexible and low-cost switch solution.
17
600 A
Dimensions - inches
Catalog number
Max. kV
kV BIL
A B C D E Porcelain Polymer
SER267 15 110 21.6 12.53 8.62 11.26 11.15 15 lbs. 10 lbs.
SER367 25 150 25.25 14.4 10.5 14.82 15.25 23 lbs. 18 lbs.
SER467 38 200 31.38 19.85 15.89 21.38 21.5 * 23 lbs.
600 A
Dimensions - inches
Catalog number
Max. kV
kV BIL
A B C D E Porcelain Polymer
SER297 15 110 21.6 12.53 8.62 11.26 11.5 16 lbs. 11 lbs.
SER397 25 150 25.25 14.4 10.5 14.82 15.25 24 lbs. 19 lbs.
SER497 38 200 31.38 19.85 15.89 21.38 21.5 * 24 lbs.
The Bridges Electric™ type SER single insulator disconnect
* Catalog number SER467 available in polymer only * Catalog number SER497 available in polymer only
Type SER numbering system
S E R X X 7 X15 kV; 110 kV BIL 225 kV; 150 kV BIL 338 kV; 200 kV BIL 4
600 A continuous current 6900 A continuous current 9
A Cable connectorsB1
Extended mounting bracketfor X-ARM mounting
B2 B3H Loadbreak hooksL Plug-In Saf-T-Gap interrupterP Polymer insulatorQB Quick breakU Underhung mountingS Hot line stud
18
The Bridges Electric™ type E distributioninterrupter switch with Saf-T-Gap interrupter
The Bridges Electric type E interrupter switch is applicable on all circuits up to 600 amperes. Although a distribution class switch, the type E meets power class stan-dards for the continuous current rating of 600 amperes. It is available in 15 kV and 25 kV ratings.
The Saf-T-Gap interrupter can be purchased as part of the original equipment or can be added later when live line switching may be required. It can be used for transformer magnetizing current, line charging current and loop switching, as well as emergency load dropping.
600 A
Catalog number Max. kV kV BIL Net weight
200 15 110 43 lbs.
300-01 25 150 49 lbs.
* Weight reflects porcelain insulators. Polymer insulators available.
The Saf-T-Gap interrupter changes in seconds with a standard
shotgun-style hookstick.
200 300-01
19
NOTE: Add suffixes below to catalog numbersfor the option described:P = Polymer insulatorK = Cable connector#6 - 397.5 MCM ACSR#6 - 500 MCM copperQB = Quick breakT = Tinned terminal padsX = Backplate setEXAMPLE: 202-02XPT = Type EF, 15 kV, 110 kVBIL, 600 A, backplate set, polymer insulators andtinned terminal pads
600 A and 900 A
Catalog number Max. kV kV BIL Net weight
202 15 110 37 lbs.
302 25 150 39 lbs.
402 38 150 39 lbs.
The Bridges Electric™ type EF distribution classdisconnect with loadbreak hooks
* Weight reflects porcelain insulators. Polymer insulators available.
For use with a loadbreak tool
202-02XT 302-02XT
www.usa.siemens.com/energy
Published by and copyright © 2010:Siemens AGEnergy SectorFreyeslebenstrasse 191058 Erlangen, Germany
Siemens Energy, Inc.99 Bolton Sullivan DriveHeber Springs, AR 72543Phone: +1 (501) 362-8296Toll-free: +1 (800) 347-6659
Order No. E50001-F630-A162-X-76USPrinted in USA TD 1112T BR 0910.5
All rights reserved. Trademarks mentioned in this document are the property of Siemens AG, its affiliates, or their respective owners.
Subject to change without prior notice. The information in this document contains general descriptions of the technical options available, which may not apply in all cases. The required technical options should therefore be specified in the contract.
Top Related