Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)First Published: 2016-02-22
Last Modified: 2016-11-18
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000 800 553-NETS (6387)Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITEDWARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITHTHE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain versionof the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDINGANYOTHERWARRANTYHEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS"WITH ALL FAULTS.CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OFMERCHANTABILITY, FITNESS FORA PARTICULAR PURPOSEANDNONINFRINGEMENTORARISING FROMACOURSEOFDEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUTLIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERSHAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, networktopology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentionaland coincidental.
This product includes cryptographic software written by Eric Young ([email protected]).
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)This product includes software written by Tim Hudson ([email protected]).
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1110R)
Please send general FSF & GNU inquiries to [email protected]. There are also other ways to contact the FSF. Please send broken links and other corrections or suggestions [email protected]. Please see the Translations README for information on coordinating and submitting translations of this article.
Copyright © 2007, 2009, 2011 Free Software Foundation, Inc. Verbatim copying and distribution of this entire article are permitted worldwide, without royalty, in any medium, providedthis notice, and the copyright notice, are preserved. Updated: Date: 2011/06/28 02:44:32
© 2016 Cisco Systems, Inc. All rights reserved.
C O N T E N T S
P r e f a c e Preface xli
Audience xli
Document Conventions xli
Related Documentation xliii
Documentation Feedback xliii
C H A P T E R 1 A Commands 1
aaa authentication login console 3
aaa authentication login default 4
aaa authentication login domain 5
aaa banner 6
aaa group server ldap 7
aaa group server radius 8
aaa group server tacacsplus 9
aaa scvmm-certificate 10
aaa user default-role 11
absolute 12
access-group 13
access-list 14
account-status 15
action 16
address-family 17
address 19
admin-state-enable 20
admin 22
advertise-subnet 23
aggregate-address 24
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) iii
allow-origin 25
allow-self-as 26
allow-writes 27
allowed-self-as-count 28
application 29
area default-cost 30
area l3out 31
area loopback 32
area nssa 33
area nssa default-information-originate 34
area nssa no-redistribute 35
area nssa translate 36
area range 37
area route-map 38
area stub 39
arp flooding 40
asn 41
attribute 42
attribute match custom 43
attribute match datacenter 44
attribute match domain 45
attribute match guest-os 46
attribute match hypervisor-id 47
attribute match ip 48
attribute match mac 49
attribute match vm-id 50
attribute match vm-name 51
attribute match vnic 52
authenticate 53
authentication-key 54
auto-cost 55
autonomous-system 56
C H A P T E R 2 B Commands 57
bandwidth 58
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)iv
Contents
basedn 59
bash 60
bfd 61
bfd ip ipv6 authentication 62
bfd ip ipv6 inherit 64
bfd ip ipv6 tenant 65
bgp 66
binddn 67
bpdu-filter 68
bridge-domain 69
C H A P T E R 3 C Commands 71
callhome 73
catalog-version 74
cdp 75
cert-chain 78
cert 79
certificate 80
channel-group 81
channel-mode 83
ciphers 86
clear-encryption-key 87
clear-pwd-history 88
clear endpoints 89
clear snapshot file 90
clear snapshot job 91
clear techsupport controllers 92
clear techsupport switch 93
clear troubleshoot epext session report 94
clear troubleshoot eptoep session report 95
clock display-format 96
clock show-offset 97
clock timezone 98
cluster-device 99
cluster-device query-device-health 100
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) v
Contents
cluster-device query-device-statistics 101
cluster-device query-device-validation 102
cluster-interface 103
comm-policy 104
configure-avs 105
configure-dvs 106
configure 107
connection intra service 108
connection terminal 109
connector 110
console 111
contract-id 112
contract 113
contract consumer 114
contract deny 117
contract enforce 119
contract provider 120
controller-group 123
controller 124
cost 125
country 126
crypto aes 127
crypto ca 128
crypto keyring 129
crypto webtoken 130
csr 131
customer-id 132
C H A P T E R 4 D Commands 133
data 135
dead-interval 136
debug log reset 137
debug log set 138
decommission controller 139
decommission switch 140
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)vi
Contents
default-information 141
default-originate 142
deploy-epg tenant application epg type 143
deploy-epg tenant application epg vlan 144
deployment-mode 145
descr 146
description 147
destination-profile 160
destination 161
destination destip 163
destination interface 164
destination tenant 165
dhcp option 167
dhcp relay policy 168
dhparam 169
direction 170
disable-connected-check 173
disable-peer-as-check 174
distance 175
dns 177
dnssearchsuffix 178
dnsservers 179
dnssuffix 180
domain 181
dsr-vip 182
dsr 183
C H A P T E R 5 E Commands 185
ebgp-multihop 187
echo-address 188
echo-mode 189
echo-rx-interval 190
email-addr 191
email-contact 192
email 193
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) vii
Contents
enable-ssl 194
encryption 195
end 196
endpoint 197
endpoint loop-detect action bd-learn-disable 198
endpoint loop-detect action port-disable 199
endpoint loop-detect enable 200
endpoint loop-detect factor 201
endpoint loop-detect interval 202
endpoint move-detection 203
endpoint retention bounce-age-interval 204
endpoint retention hold-interval 205
endpoint retention local-age-interval 206
endpoint retention move-frequency 207
endpoint retention policy 208
endpoint retention remote-age-interval 209
enforce-subnet-learning 210
epg 211
eraseconfig 212
errdisable recovery cause bpduguard 213
errdisable recovery cause ep-move 214
errdisable recovery cause mcp-loop 215
errdisable recovery interval 216
erspan-id 217
exec 219
exit 220
expiration 221
expires 222
export 223
external-l2 224
external-l3 225
external-l3 epg 226
C H A P T E R 6 F Commands 227
fabric clear 228
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)viii
Contents
fabric show 229
fex-interface-group 230
fex-profile 231
fex 232
file 233
filter 234
filter tenant bd 236
filter tenant vrf 237
firewall-logging 238
firewall 239
firmware-version 240
firmware 241
firmware repository add 242
firmware repository delete 243
firmware upgrade controller-group 244
firmware upgrade switch-group 245
first-file 246
first-name 247
format 248
C H A P T E R 7 G Commands 249
graceful-restart-helper 250
graceful-restart 251
group 252
C H A P T E R 8 H Commands 253
hello-interval 254
http 255
https 256
C H A P T E R 9 I Commands 257
inband-mgmt 261
inband-mgmt epg 262
inherit 263
inherit bgp address-family 266
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) ix
Contents
inherit bgp dampening 267
inherit eigrp 268
inherit ipv4 269
inherit ipv6 270
instance 272
interface 273
interface ethernet 275
interface inband-mgmt0 276
interface mgmt0 277
interface port-channel 278
interface vlan 279
interface vpc 280
ip 281
ip address-range 282
ip address 284
ip address tenant application 287
ip address tenant external-l2 289
ip address tenant external-l3 291
ip bandwidth 293
ip bfd 295
ip dhcp relay address tenant application 297
ip dhcp relay address tenant external-l2 298
ip dhcp relay address tenant external-l3 299
ip distribute-list eigrp 300
ip dscp 301
ip hello-interval 303
ip hold-interval 305
ip igmp snooping fast-leave 307
ip igmp snooping last-member-query-interval 308
ip igmp snooping optimise-multicast-flood 309
ip igmp snooping policy 310
ip igmp snooping querier 311
ip igmp snooping query-interval 312
ip igmp snooping query-max-response-time 313
ip igmp snooping startup-query-count 314
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)x
Contents
ip igmp snooping startup-query-interval 315
ip next-hop-self 316
ip ospf authentication-key 318
ip ospf authentication 319
ip ospf bfd 320
ip ospf cost 321
ip ospf dead-interval 322
ip ospf hello-interval 323
ip ospf inherit 324
ip ospf mtu-ignore 325
ip ospf network 326
ip ospf passive-interface 327
ip ospf prefix-suppression 328
ip ospf priority 329
ip ospf retransmit-interval 330
ip ospf transmit-delay 331
ip passive-interface 332
ip prefix-list 334
ip prefix-list permit le 335
ip router eigrp 336
ip router ospf default 337
ip shared address consumer 338
ip shared address provider 339
ip split-horizon 340
ip summary-address eigrp 342
ip throughput-delay 343
ip ttl 345
iprange 347
ipv6 348
ipv6 address-range 349
ipv6 address 351
ipv6 address tenant application 354
ipv6 address tenant external-l2 356
ipv6 address tenant external-l3 358
ipv6 bandwidth 360
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xi
Contents
ipv6 bfd 361
ipv6 dhcp relay address tenant application 362
ipv6 dhcp relay address tenant external-l2 363
ipv6 dhcp relay address tenant external-l3 364
ipv6 distribute-list eigrp 365
ipv6 hello-interval 366
ipv6 hold-interval 367
ipv6 link-local 368
ipv6 nd hop-limit 370
ipv6 nd managed-config-flag 372
ipv6 nd mtu 374
ipv6 nd ns-interval 376
ipv6 nd ns-retries 378
ipv6 nd other-config-flag 380
ipv6 nd policy 382
ipv6 nd prefix 383
ipv6 nd ra-interval 385
ipv6 nd ra-lifetime 387
ipv6 nd reachable-time 389
ipv6 nd retrans-timer 391
ipv6 nd suppress-ra-mtu 393
ipv6 nd suppress-ra 395
ipv6 next-hop-self 397
ipv6 ospf bfd 398
ipv6 ospf cost 399
ipv6 ospf dead-interval 400
ipv6 ospf hello-interval 401
ipv6 ospf inherit 402
ipv6 ospf mtu-ignore 403
ipv6 ospf network 404
ipv6 ospf passive-interface 405
ipv6 ospf prefix-suppression 406
ipv6 ospf priority 407
ipv6 ospf retransmit-interval 408
ipv6 ospf transmit-delay 409
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xii
Contents
ipv6 passive-interface 410
ipv6 router eigrp 411
ipv6 router ospf default 412
ipv6 shared address consumer 413
ipv6 shared address provider 414
ipv6 split-horizon 415
ipv6 throughput-delay 416
isis 418
isolation 419
C H A P T E R 1 0 K Commands 421
key 422
C H A P T E R 1 1 L Commands 423
l2-unknown-unicast 425
l3-unknown-multicast 426
l3out 427
l4l7-peer 428
l4l7 429
l4l7 cluster import-from 430
l4l7 cluster name 431
l4l7 graph 432
label match 433
label name 434
lacp fast-select-hot-standby 435
lacp graceful-convergence 436
lacp load-defer 437
lacp max-links 438
lacp min-links 440
lacp port-priority 442
lacp port-priority interface 444
lacp rate 445
lacp rate fast normal interface 447
lacp suspend-individual 448
last-name 449
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xiii
Contents
ldap-server attribute 450
ldap-server basedn 451
ldap-server filter 452
ldap-server host 453
ldap-server retries 454
ldap-server timeout 455
leaf-group 456
leaf-interface-group 457
leaf-interface-profile 458
leaf-policy-group 459
leaf-profile 460
leaf 461
legacy 462
link 463
lldp 466
lldp holdtime 469
lldp reinit 470
lldp timer 471
local-as 472
locality 473
logfile 474
logging 475
logging audit 476
logging description 477
logging event 478
logging fault 479
logging server-group 480
logging session 481
logging severity 482
lsp-fast-flood 484
lsp-gen-interval 485
lsp-mtu 486
C H A P T E R 1 2 MCommands 487
mac-address 489
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xiv
Contents
match 491
match arp 492
match bridge-domain 493
match community 494
match icmp 495
match ip 496
match ipv6 497
match prefix-list 498
match raw 499
match tcp 500
match udp 501
max-lsa 502
max-validity-period 503
max concurrent 504
max running 505
maximum-paths 506
maximum-prefix 508
mcp 509
mcp action 511
mcp enable 512
mcp factor 513
mcp init-delay 514
mcp transmit-frequency 515
member 516
message-level 517
message-size 518
metric 519
mgmt-epg 520
microsoft-domain 521
microsoft 522
min-rx 523
min-tx 524
min 525
mode 526
modulus 527
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xv
Contents
monitor 528
monitor access 529
monitor fabric 530
monitor tenant 531
monitor virtual 532
mtu-ignore 533
mtu 534
multi-destination 537
multi-site-mac-address 538
multicast-address 539
multiplier 540
C H A P T E R 1 3 N Commands 541
name-lookup 542
negotiate 543
neighbor 545
network 546
next-hop-self 547
ntp 548
C H A P T E R 1 4 O Commands 549
oob-mgmt 550
oob-mgmt epg 551
optimize 552
option 553
org-name 554
org-unit-name 555
C H A P T E R 1 5 P Commands 557
passive-interface 559
passphrase 560
password 561
password change-count 563
password change-during-interval 564
password change-interval 565
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xvi
Contents
password history-count 566
password no-change-interval 567
password pwd-strength-check 568
path 569
peer-dead-interval 570
periodic-inventory notification 571
phone-contact 572
phone 573
pod 574
policy-group 575
policy-map 577
policy-map type data-plane 578
policy-map type qos 579
port 580
porttrack delay 583
porttrack minlinks 584
porttrack state 585
power 586
prefix-suppression 587
preview 588
priority 589
priv-type 590
priv 591
private-as-control 592
protocol 593
pwd-lifetime 594
C H A P T E R 1 6 Q Commands 595
qos parameters 596
qos preserve 597
query-cluster-health 598
query-cluster-statistics 599
query-cluster-validation 600
query-profile 601
query 602
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xvii
Contents
queue control 603
queue limit 604
C H A P T E R 1 7 R Commands 605
radius-server host 607
radius-server retries 608
radius-server timeout 609
rbac role 610
rbac rule 611
rbac security-domain 612
realm 613
recurring 614
redirect 615
redistribute 616
redundancy-mode 617
region 618
reload controller 619
reload switch 620
remote-as 621
remote 622
request-status-count 624
reset-to-factory 625
response-incl 626
response-subtree 627
retransmit-interval 628
retries 629
revision 630
role 631
route-map 632
route-profile 633
route-reflector 634
router-id 635
router bgp 636
router eigrp 637
router ospf 638
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xviii
Contents
rtr-cfg 639
run-mode 640
C H A P T E R 1 8 S Commands 641
schedule 661
scheduler 662
scheduling 663
scope 664
scvmm 665
second-file 666
security-domain 667
security 668
send-community 669
server 670
service-policy 673
service 676
session-record-flags 677
set 678
set burst 680
set cir 681
set community 682
set conform-cos-transmit 685
set conform-dscp-transmit 686
set conform 687
set dampening 688
set dscp 689
set exceed-cos-transmit 690
set exceed-dscp-transmit 691
set exceed 692
set excessive-burst 693
set local-preference 694
set metric-type 696
set metric 698
set mode 700
set pir 701
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xix
Contents
set qos-class 702
set tag 703
set target-dscp 705
set type 706
set violate-cos-transmit 707
set violate-dscp-transmit 708
set violate 709
set weight 710
shellinabox 712
show aaa authentication 713
show aaa groups 714
show access-list 715
show accounting log 716
show application 717
show audits 718
show audits tenant 719
show audits tenant application 720
show audits tenant application epg 721
show audits tenant bridge-domain 722
show audits tenant bridge-domain detail 723
show audits tenant interface bridge-domain 724
show audits tenant interface bridge-domain detail 725
show audits tenant vrf 726
show audits tenant vrf detail 727
show audits tenant vrf external-l3 bgp 728
show audits tenant vrf external-l3 bgp node 729
show audits tenant vrf external-l3 eigrp 730
show audits tenant vrf external-l3 eigrp detail 731
show audits tenant vrf external-l3 epg 732
show audits tenant vrf external-l3 epg detail 733
show audits tenant vrf external-l3 epg name 734
show audits tenant vrf external-l3 epg name detail 735
show audits tenant vrf external-l3 interfaces 736
show audits tenant vrf external-l3 interfaces detail 737
show audits tenant vrf external-l3 ospf 738
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xx
Contents
show audits tenant vrf external-l3 ospf detail 739
show audits tenant vrf external-l3 static-route 740
show audits tenant vrf external-l3 static-route detail 741
show audits tenant vrf external-l3 static-route node 742
show audits tenant vrf external-l3 static-route node detail 743
show bridge-domain 744
show bridge-domain detail 745
show callhome 746
show callhome common destination-profile 747
show callhome common query-profile 748
show callhome common transport-email 749
show catalog 750
show cli command 751
show cli internal audit 752
show cli internal transaction 753
show cli list 754
show cli manpage 755
show cli path 756
show clock 757
show communication ciphers 758
show communication http 759
show communication https 760
show communication shellinabox 761
show communication ssh-service 762
show communication telnet 763
show communication web-requests 764
show contract-type 765
show contract 766
show controller 767
show controller detail 768
show cores 769
show debug counter 770
show debug log 771
show dns-address 772
show dns-domain 773
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxi
Contents
show endpoints 774
show endpoints leaf interface ethernet 775
show endpoints leaf interface port-channel 776
show endpoints vpc 777
show epg 778
show epg detail 779
show events 780
show events controller 781
show events controller detail 782
show events leaf 783
show events leaf fex 784
show events leaf fex module 785
show events leaf interface ethernet 786
show events leaf interface l3instance 787
show events leaf interface mgmt 788
show events leaf interface portchannel 789
show events leaf interface tunnel 790
show events leaf inventory chassis 791
show events leaf inventory fans 792
show events leaf inventory module 793
show events leaf inventory module fabricport 794
show events leaf inventory module leafport 795
show events leaf inventory powersupply 796
show events leaf inventory supervisor 797
show events leaf protocol 798
show events leaf vpc 799
show events leaf vrf 800
show events spine 801
show events spine interface ethernet 802
show events spine interface l3instance 803
show events spine interface mgmt 804
show events spine interface tunnel 805
show events spine inventory chassis 806
show events spine inventory fabric 807
show events spine inventory fans 808
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxii
Contents
show events spine inventory module 809
show events spine inventory module fabricport 810
show events spine inventory powersupply 811
show events spine inventory supervisor 812
show events spine inventory system 813
show events spine protocol 814
show events spine vrf 815
show events tenant 816
show events tenant application 817
show events tenant application epg 818
show events tenant bridge-domain 819
show events tenant bridge-domain detail 820
show events tenant endpoints 821
show events tenant endpoints leaf interface ethernet 822
show events tenant endpoints leaf interface port-channel 823
show events tenant endpoints vpc 824
show events tenant interface bridge-domain 826
show events tenant interface bridge-domain detail 827
show events tenant vrf 828
show events tenant vrf detail 829
show events tenant vrf external-l3 bgp 830
show events tenant vrf external-l3 bgp node 831
show events tenant vrf external-l3 eigrp 832
show events tenant vrf external-l3 eigrp detail 833
show events tenant vrf external-l3 epg 834
show events tenant vrf external-l3 epg detail 835
show events tenant vrf external-l3 epg name 836
show events tenant vrf external-l3 epg name detail 837
show events tenant vrf external-l3 interfaces 838
show events tenant vrf external-l3 interfaces detail 839
show events tenant vrf external-l3 ospf 840
show events tenant vrf external-l3 ospf detail 841
show events tenant vrf external-l3 route-map 842
show events tenant vrf external-l3 route-map detail 843
show events tenant vrf external-l3 static-route 844
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxiii
Contents
show events tenant vrf external-l3 static-route detail 845
show events tenant vrf external-l3 static-route node 846
show events tenant vrf external-l3 static-route node detail 847
show external-l2 epg 848
show external-l2 epg name 849
show external-l2 epg tenant 850
show external-l3 bgp 851
show external-l3 bgp tenant 852
show external-l3 bgp tenant vrf 853
show external-l3 bgp tenant vrf node 854
show external-l3 eigrp 855
show external-l3 eigrp detail 856
show external-l3 eigrp node 857
show external-l3 eigrp node detail 858
show external-l3 eigrp tenant 859
show external-l3 eigrp tenant detail 860
show external-l3 eigrp tenant vrf 861
show external-l3 eigrp tenant vrf detail 862
show external-l3 eigrp tenant vrf node 863
show external-l3 eigrp tenant vrf node detail 864
show external-l3 epg 865
show external-l3 epg detail 866
show external-l3 epg name 867
show external-l3 epg name detail 868
show external-l3 epg tenant 869
show external-l3 epg tenant detail 870
show external-l3 epg tenant vrf 871
show external-l3 epg tenant vrf detail 872
show external-l3 interfaces 873
show external-l3 interfaces detail 874
show external-l3 interfaces node 875
show external-l3 interfaces node detail 876
show external-l3 interfaces tenant 877
show external-l3 interfaces tenant detail 878
show external-l3 interfaces tenant vrf 879
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxiv
Contents
show external-l3 interfaces tenant vrf detail 880
show external-l3 interfaces tenant vrf node 881
show external-l3 interfaces tenant vrf node detail 882
show external-l3 ospf 883
show external-l3 ospf detail 884
show external-l3 ospf node 885
show external-l3 ospf node detail 886
show external-l3 ospf tenant 887
show external-l3 ospf tenant detail 888
show external-l3 ospf tenant vrf 889
show external-l3 ospf tenant vrf detail 890
show external-l3 ospf tenant vrf node 891
show external-l3 ospf tenant vrf node detail 892
show external-l3 route-map 893
show external-l3 route-map detail 894
show external-l3 route-map name 895
show external-l3 route-map name detail 896
show external-l3 route-map tenant 897
show external-l3 route-map tenant detail 898
show external-l3 route-map tenant vrf 899
show external-l3 route-map tenant vrf detail 900
show external-l3 route-map tenant vrf node 901
show external-l3 route-map tenant vrf node detail 902
show external-l3 static-route 903
show external-l3 static-route detail 904
show external-l3 static-route node 905
show external-l3 static-route node detail 906
show external-l3 static-route tenant 907
show external-l3 static-route tenant detail 908
show external-l3 static-route tenant vrf 909
show external-l3 static-route tenant vrf detail 910
show external-l3 static-route tenant vrf node 911
show external-l3 static-route tenant vrf node detail 912
show fabric-recovery status 913
show faults 914
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxv
Contents
show faults controller 916
show faults controller detail 917
show faults l4l7-cluster 918
show faults l4l7-graph 919
show faults leaf 920
show faults leaf fex 921
show faults leaf fex module 922
show faults leaf interface ethernet 923
show faults leaf interface l3instance 924
show faults leaf interface mgmt 925
show faults leaf interface portchannel 926
show faults leaf interface tunnel 927
show faults leaf inventory chassis 928
show faults leaf inventory fans 929
show faults leaf inventory module 930
show faults leaf inventory module fabricport 931
show faults leaf inventory module leafport 932
show faults leaf inventory powersupply 933
show faults leaf inventory supervisor 934
show faults leaf protocol 935
show faults leaf vpc 936
show faults leaf vrf 937
show faults microsoft domain 938
show faults microsoft domain name 939
show faults microsoft domain name hyperv 940
show faults microsoft domain name port-group 941
show faults microsoft domain name scvmm 942
show faults microsoft domain name vm 943
show faults microsoft domain name vm name 944
show faults spine 945
show faults spine interface ethernet 946
show faults spine interface l3instance 947
show faults spine interface mgmt 948
show faults spine interface tunnel 949
show faults spine inventory chassis 950
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxvi
Contents
show faults spine inventory fabric 951
show faults spine inventory fans 952
show faults spine inventory module 953
show faults spine inventory module fabricport 954
show faults spine inventory powersupply 955
show faults spine inventory supervisor 956
show faults spine inventory system 957
show faults spine protocol 958
show faults spine vrf 959
show faults tenant 960
show faults tenant application 961
show faults tenant application epg 962
show faults tenant bridge-domain 963
show faults tenant bridge-domain detail 964
show faults tenant interface bridge-domain 965
show faults tenant interface bridge-domain detail 966
show faults tenant vrf 967
show faults tenant vrf detail 968
show faults tenant vrf external-l3 bgp 969
show faults tenant vrf external-l3 bgp node 970
show faults tenant vrf external-l3 eigrp 971
show faults tenant vrf external-l3 eigrp detail 972
show faults tenant vrf external-l3 epg 973
show faults tenant vrf external-l3 epg detail 974
show faults tenant vrf external-l3 epg name 975
show faults tenant vrf external-l3 epg name detail 976
show faults tenant vrf external-l3 interfaces 977
show faults tenant vrf external-l3 interfaces detail 978
show faults tenant vrf external-l3 ospf 979
show faults tenant vrf external-l3 ospf detail 980
show faults tenant vrf external-l3 static-route 981
show faults tenant vrf external-l3 static-route detail 982
show faults tenant vrf external-l3 static-route node 983
show faults tenant vrf external-l3 static-route node detail 984
show faults vmware domain 985
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxvii
Contents
show faults vmware domain name 986
show faults vmware domain name epg 987
show faults vmware domain name esx 988
show faults vmware domain name port-group 989
show faults vmware domain name vcenter 990
show faults vmware domain name vm 991
show faults vmware domain name vm name 992
show firmware repository 993
show firmware repository detail 994
show firmware upgrade status 995
show firmware upgrade status controller-group 996
show firmware upgrade status controller-group detail 997
show firmware upgrade status detail 998
show firmware upgrade status switch-group 999
show firmware upgrade status switch-group detail 1000
show health 1001
show health l4l7-cluster 1002
show health l4l7-graph 1003
show health leaf 1004
show health leaf fex 1005
show health leaf fex module 1006
show health leaf interface ethernet 1007
show health leaf interface l3instance 1008
show health leaf interface mgmt 1009
show health leaf interface portchannel 1010
show health leaf interface tunnel 1011
show health leaf inventory chassis 1012
show health leaf inventory fans 1013
show health leaf inventory module 1014
show health leaf inventory module fabricport 1015
show health leaf inventory module leafport 1016
show health leaf inventory powersupply 1017
show health leaf inventory supervisor 1018
show health leaf protocol 1019
show health leaf vpc 1020
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxviii
Contents
show health leaf vrf 1021
show health spine 1022
show health spine interface ethernet 1023
show health spine interface l3instance 1024
show health spine interface mgmt 1025
show health spine interface tunnel 1026
show health spine inventory chassis 1027
show health spine inventory fabric 1028
show health spine inventory fans 1029
show health spine inventory module 1030
show health spine inventory module fabricport 1031
show health spine inventory powersupply 1032
show health spine inventory supervisor 1033
show health spine inventory system 1034
show health spine protocol 1035
show health spine vrf 1036
show health tenant 1037
show health tenant application 1038
show health tenant application epg 1039
show health tenant bridge-domain 1040
show health tenant bridge-domain detail 1041
show health tenant interface bridge-domain 1042
show health tenant interface bridge-domain detail 1043
show health tenant vrf 1044
show health tenant vrf detail 1045
show health tenant vrf external-l3 bgp 1046
show health tenant vrf external-l3 bgp node 1047
show health tenant vrf external-l3 eigrp 1048
show health tenant vrf external-l3 eigrp detail 1049
show health tenant vrf external-l3 epg 1050
show health tenant vrf external-l3 epg detail 1051
show health tenant vrf external-l3 epg name 1052
show health tenant vrf external-l3 epg name detail 1053
show health tenant vrf external-l3 interfaces 1054
show health tenant vrf external-l3 interfaces detail 1055
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxix
Contents
show health tenant vrf external-l3 ospf 1056
show health tenant vrf external-l3 ospf detail 1057
show health tenant vrf external-l3 static-route 1058
show health tenant vrf external-l3 static-route detail 1059
show health tenant vrf external-l3 static-route node 1060
show health tenant vrf external-l3 static-route node detail 1061
show inband-mgmt 1062
show inband-mgmt controller 1063
show inband-mgmt switch 1064
show interface bridge-domain 1065
show interface bridge-domain detail 1066
show ip interface bridge-domain 1067
show ipv6 interface bridge-domain 1068
show l4l7-cluster 1069
show l4l7-graph 1070
show l4l7-package 1071
show ldap-server 1072
show locator-led 1073
show locator-led status leaf 1074
show microsoft domain 1075
show microsoft domain name 1076
show microsoft domain name hyperv 1077
show microsoft domain name port-group 1078
show microsoft domain name scvmm 1079
show microsoft domain name vm 1080
show microsoft domain name vm name 1081
show microsoft vm 1082
show monitor access 1083
show monitor fabric 1084
show monitor tenant 1085
show monitor virtual 1086
show ntpq 1087
show oob-mgmt 1088
show oob-mgmt controller 1089
show oob-mgmt switch 1090
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxx
Contents
show policy-map 1091
show policy-map type data-plane 1092
show policy-map type qos 1093
show port-channel leaf 1094
show port-channel map 1095
show port-channel map leaf 1096
show radius-server 1097
show resource 1098
show resource conflict encap-vlan epg 1099
show resource conflict encap-vlan epg node 1100
show role 1101
show running-config 1102
show sessions 1103
show sessions controller 1104
show sessions controller detail 1105
show sessions leaf 1106
show sessions spine 1107
show snapshot active 1108
show snapshot files 1109
show snapshot jobs 1110
show snmp 1111
show snmp clientgroups 1112
show snmp community 1113
show snmp engineid 1114
show snmp hosts 1115
show snmp users 1116
show stats 1117
show stats granularity leaf 1118
show stats granularity leaf fex 1119
show stats granularity leaf fex module 1120
show stats granularity leaf interface ethernet 1121
show stats granularity leaf interface mgmt 1122
show stats granularity leaf interface portchannel 1123
show stats granularity leaf inventory fans 1124
show stats granularity leaf inventory powersupply 1125
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxi
Contents
show stats granularity leaf inventory supervisor 1126
show stats granularity spine 1127
show stats granularity spine interface ethernet 1128
show stats granularity spine interface mgmt 1129
show stats granularity spine inventory chassis 1130
show stats granularity spine inventory fabric 1131
show stats granularity spine inventory fans 1132
show stats granularity spine inventory module 1133
show stats granularity spine inventory powersupply 1134
show stats granularity spine inventory supervisor 1135
show stats granularity spine inventory system 1136
show stats granularity tenant 1137
show stats granularity tenant application 1138
show stats granularity tenant application epg 1139
show switch 1140
show switch detail 1141
show tacacs-server 1142
show techsupport all 1143
show techsupport controllers 1144
show techsupport host 1145
show techsupport switch 1146
show tenant 1147
show tenant access-list 1148
show tenant application 1149
show tenant application endpoints 1150
show tenant application endpoints leaf interface ethernet 1151
show tenant application endpoints leaf interface port-channel 1152
show tenant application endpoints vpc 1153
show tenant application epg 1154
show tenant application epg detail 1155
show tenant application epg endpoints 1156
show tenant application epg endpoints leaf interface ethernet 1157
show tenant application epg endpoints leaf interface port-channel 1158
show tenant application epg endpoints vpc 1159
show tenant bridge-domain 1161
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxii
Contents
show tenant bridge-domain detail 1162
show tenant contract-type 1163
show tenant contract 1164
show tenant detail 1165
show tenant endpoints 1166
show tenant endpoints leaf interface ethernet 1167
show tenant endpoints leaf interface port-channel 1168
show tenant endpoints vpc 1169
show tenant epg 1170
show tenant epg detail 1171
show tenant external-l2 epg 1172
show tenant interface bridge-domain 1173
show tenant interface bridge-domain detail 1174
show tenant ip interface bridge-domain 1175
show tenant ipv6 interface bridge-domain 1176
show tenant policy-map 1177
show tenant policy-map type data-plane 1178
show tenant policy-map type qos 1179
show tenant vrf 1180
show tenant vrf detail 1181
show tenant vrf external-l3 bgp 1182
show tenant vrf external-l3 bgp node 1183
show tenant vrf external-l3 eigrp 1184
show tenant vrf external-l3 eigrp detail 1185
show tenant vrf external-l3 epg 1186
show tenant vrf external-l3 epg detail 1187
show tenant vrf external-l3 epg name 1188
show tenant vrf external-l3 epg name detail 1189
show tenant vrf external-l3 interfaces 1190
show tenant vrf external-l3 interfaces detail 1191
show tenant vrf external-l3 ospf 1192
show tenant vrf external-l3 ospf detail 1193
show tenant vrf external-l3 route-map 1194
show tenant vrf external-l3 route-map detail 1195
show tenant vrf external-l3 static-route 1196
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxiii
Contents
show tenant vrf external-l3 static-route detail 1197
show tenant vrf external-l3 static-route node 1198
show tenant vrf external-l3 static-route node detail 1199
show troubleshoot epext session 1200
show troubleshoot epext session atomiccounter 1201
show troubleshoot epext session audit 1202
show troubleshoot epext session contracts 1203
show troubleshoot epext session deployments 1204
show troubleshoot epext session events 1205
show troubleshoot epext session faults 1206
show troubleshoot epext session monitor 1207
show troubleshoot epext session reports 1208
show troubleshoot epext session statistics 1209
show troubleshoot epext session topology 1210
show troubleshoot epext session traceroute 1211
show troubleshoot epext sessions 1212
show troubleshoot eptoep session 1213
show troubleshoot eptoep session atomiccounter 1214
show troubleshoot eptoep session audit 1215
show troubleshoot eptoep session contracts 1216
show troubleshoot eptoep session deployments 1217
show troubleshoot eptoep session events 1218
show troubleshoot eptoep session faults 1219
show troubleshoot eptoep session monitor 1220
show troubleshoot eptoep session reports 1221
show troubleshoot eptoep session statistics 1222
show troubleshoot eptoep session topology 1223
show troubleshoot eptoep session traceroute 1224
show troubleshoot eptoep sessions 1225
show username 1226
show username detail 1227
show version 1228
show vlan-domain 1229
show vmware domain 1230
show vmware domain name 1231
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxiv
Contents
show vmware domain name epg 1232
show vmware domain name esx 1233
show vmware domain name port-group 1234
show vmware domain name vcenter 1235
show vmware domain name vm 1236
show vmware domain name vm name 1237
show vmware vm 1238
show vpc 1239
show vpc map leaf 1240
show vrf 1241
show vrf detail 1242
shut 1243
shutdown 1244
site-id 1246
slow-timer 1247
snapshot download 1248
snapshot export 1249
snapshot import 1250
snapshot rollback 1251
snapshot upload 1252
snmp-server clientgroup 1253
snmp-server community 1254
snmp-server contact 1255
snmp-server host 1256
snmp-server location 1257
snmp-server protocol 1258
snmp-server user 1259
source 1260
source application 1261
source interface ethernet 1262
source interface port-channel 1263
source interface vpc 1264
spanning-tree 1265
spanning-tree bpdu-filter 1268
spanning-tree bpdu-guard 1269
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxv
Contents
speed 1270
spf-interval 1272
ssh-key 1273
ssh-service 1274
ssl-protocols 1275
ssl-validation-level 1276
state 1277
static-endpoint 1278
static-tep 1281
statistics 1283
storm-control level 1284
storm-control pps 1286
street-address 1289
subject 1290
summary-address 1291
switch-group 1292
switch 1293
switching 1294
switchport 1295
switchport access vlan tenant application 1297
switchport access vlan tenant external-svi 1299
switchport trunk allowed vlan inband-mgmt 1301
switchport trunk allowed vlan tenant application 1302
switchport trunk allowed vlan tenant external-l2 1304
switchport trunk allowed vlan tenant external-svi 1306
switchport trunk allowed vlan tenant legacy-forwarding 1308
switchport trunk native vlan tenant application 1310
switchport trunk native vlan tenant external-svi 1312
switchport vlan 1314
syslog 1316
system cluster-size 1317
system controller-id 1318
system dynamic-load-balance 1319
system fabric-security-mode 1320
system jumbomtu 1321
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxvi
Contents
system switch-id 1322
C H A P T E R 1 9 T Commands 1323
tacacs-server host 1327
tacacs-server retries 1328
tacacs-server timeout 1329
tag 1330
target 1332
telnet 1333
template bfd 1334
template bgp address-family 1335
template bgp timers 1336
template community-list expanded 1337
template community-list standard 1338
template dhcp option 1339
template dhcp relay 1340
template eigrp interface-policy 1341
template eigrp vrf-policy 1342
template endpoint retention policy 1343
template extcommunity-list expanded 1344
template extcommunity-list standard 1345
template ip igmp snooping policy 1346
template ipv6 nd policy 1347
template ipv6 nd prefix 1348
template leaf-policy-group 1349
template ospf interface-policy 1350
template ospf vrf-policy 1351
template policy-group 1352
template port-channel 1353
template route-profile 1354
template route tag 1355
tenant 1356
terminal 1357
time 1358
time start daily 1359
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxvii
Contents
time start weekly 1360
timeout 1361
timers 1362
timers lsa-arrival 1364
timers lsa-group-pacing 1365
timers throttle lsa 1366
timers throttle spf 1367
tp 1368
transmit-delay 1369
transport email from 1370
transport email mail-server 1371
transport email reply-to 1372
trigger fabric-recovery 1373
trigger shutdown 1374
trigger snapshot download 1375
trigger snapshot export 1376
trigger snapshot import 1377
trigger snapshot rollback 1378
trigger snapshot upload 1379
trigger techsupport all 1380
trigger techsupport controllers 1381
trigger techsupport host 1382
trigger techsupport local 1383
trigger techsupport switch 1384
trigger troubleshoot epext session report 1385
trigger troubleshoot eptoep session report 1386
trigger vmware 1387
troubleshoot epext session atomiccounter 1388
troubleshoot epext session description 1389
troubleshoot epext session latestminutes 1390
troubleshoot epext session monitor destination apic 1391
troubleshoot epext session monitor destination prefdestgroup 1392
troubleshoot epext session monitor destination tenant 1393
troubleshoot epext session scheduler 1395
troubleshoot epext session srcextip destip tenant application 1396
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xxxviii
Contents
troubleshoot epext session srcextip destip tenant vrf 1397
troubleshoot epext session srcip tenant application epg destextip 1398
troubleshoot epext session srcip tenant vrf destextip 1399
troubleshoot epext session starttime 1400
troubleshoot epext session traceroute 1401
troubleshoot epext session traceroute protocol icmp 1402
troubleshoot epext session traceroute protocol tcp 1403
troubleshoot epext session traceroute protocol udp 1404
troubleshoot eptoep session atomiccounter 1405
troubleshoot eptoep session description 1406
troubleshoot eptoep session latestminutes 1407
troubleshoot eptoep session monitor destination apic 1408
troubleshoot eptoep session monitor destination prefdestgroup 1409
troubleshoot eptoep session monitor destination tenant 1410
troubleshoot eptoep session scheduler 1412
troubleshoot eptoep session srcip tenant application epg destip tenant application 1413
troubleshoot eptoep session srcip tenant application epg destip tenant vrf 1414
troubleshoot eptoep session srcip tenant vrf destip tenant application 1415
troubleshoot eptoep session srcip tenant vrf destip tenant vrf 1416
troubleshoot eptoep session srcmac tenant application epg destmac tenant application 1417
troubleshoot eptoep session srcmac tenant application epg destmac tenant vrf 1419
troubleshoot eptoep session srcmac tenant vrf destmac tenant application 1420
troubleshoot eptoep session srcmac tenant vrf destmac tenant vrf 1421
troubleshoot eptoep session starttime 1422
troubleshoot eptoep session traceroute 1423
troubleshoot eptoep session traceroute protocol icmp 1424
troubleshoot eptoep session traceroute protocol tcp 1425
troubleshoot eptoep session traceroute protocol udp 1426
trusted-key 1427
C H A P T E R 2 0 U Commands 1429
ui-idle-timeout-seconds 1430
unicast 1431
update-source ethernet 1432
update-source loopback 1433
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xxxix
Contents
update-source vlan 1434
use-keyring 1435
use-vrf 1436
user 1437
username 1438
C H A P T E R 2 1 V Commands 1441
vcenter 1442
vlan-domain 1443
vlan-pool 1447
vlan 1448
vmware-domain 1450
vnic 1451
vpc context 1452
vpc domain consecutive 1453
vpc domain explicit 1454
vpc domain reciprocal 1455
vrf 1456
vshield 1461
vxlan 1462
vxlan multicast-pool 1463
vxlan pool 1464
C H A P T E R 2 2 WCommands 1465
webtoken-timeout-seconds 1466
weight 1467
where 1468
where detail 1469
winservers 1470
C H A P T E R 2 3 Z Commands 1471
zone 1472
zones 1473
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xl
Contents
Preface
• Audience, page xli
• Document Conventions, page xli
• Related Documentation, page xliii
• Documentation Feedback, page xliii
AudienceThis guide is intended for network and systems administrators who configure and maintain the ApplicationCentric Infrastructure fabric.
Document ConventionsCommand descriptions use the following conventions:
DescriptionConvention
Bold text indicates the commands and keywords that you enter literallyas shown.
bold
Italic text indicates arguments for which the user supplies the values.Italic
Square brackets enclose an optional element (keyword or argument).[x]
Square brackets enclosing keywords or arguments separated by a verticalbar indicate an optional choice.
[x | y]
Braces enclosing keywords or arguments separated by a vertical barindicate a required choice.
{x | y}
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xli
DescriptionConvention
Nested set of square brackets or braces indicate optional or requiredchoices within optional or required elements. Braces and a vertical barwithin square brackets indicate a required choice within an optionalelement.
[x {y | z}]
Indicates a variable for which you supply values, in context where italicscannot be used.
variable
A nonquoted set of characters. Do not use quotation marks around thestring or the string will include the quotation marks.
string
Examples use the following conventions:
DescriptionConvention
Terminal sessions and information the switch displays are in screen font.screen font
Information you must enter is in boldface screen font.boldface screen font
Arguments for which you supply values are in italic screen font.italic screen font
Nonprinting characters, such as passwords, are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a lineof code indicates a comment line.
!, #
This document uses the following conventions:
Means reader take note. Notes contain helpful suggestions or references to material not covered in themanual.
Note
Means reader be careful. In this situation, you might do something that could result in equipment damageor loss of data.
Caution
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xlii
PrefaceDocument Conventions
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. Use the statement number provided at the end of each warningto locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Warning
Related DocumentationCisco Application Centric Infrastructure (ACI) Documentation
The ACI documentation is available at the following URL: http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.
Cisco Application Centric Infrastructure (ACI) Simulator Documentation
The Cisco ACI Simulator documentation is available at http://www.cisco.com/c/en/us/support/cloud-systems-management/application-centric-infrastructure-simulator/tsd-products-support-series-home.html.
Cisco Nexus 9000 Series Switches Documentation
The Cisco Nexus 9000 Series Switches documentation is available at http://www.cisco.com/c/en/us/support/switches/nexus-9000-series-switches/tsd-products-support-series-home.html.
Cisco Application Virtual Switch Documentation
The Cisco Application Virtual Switch (AVS) documentation is available at http://www.cisco.com/c/en/us/support/switches/application-virtual-switch/tsd-products-support-series-home.html.
Cisco Application Centric Infrastructure (ACI) Integration with OpenStack Documentation
Cisco ACI integration with OpenStack documentation is available at http://www.cisco.com/c/en/us/support/cloud-systems-management/application-policy-infrastructure-controller-apic/tsd-products-support-series-home.html.
Documentation FeedbackTo provide technical feedback on this document, or to report an error or omission, please send your commentsto [email protected]. We appreciate your feedback.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) xliii
PrefaceRelated Documentation
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)xliv
PrefaceDocumentation Feedback
A Commands
• aaa authentication login console, page 3
• aaa authentication login default, page 4
• aaa authentication login domain, page 5
• aaa banner, page 6
• aaa group server ldap, page 7
• aaa group server radius, page 8
• aaa group server tacacsplus, page 9
• aaa scvmm-certificate, page 10
• aaa user default-role, page 11
• absolute, page 12
• access-group, page 13
• access-list, page 14
• account-status, page 15
• action, page 16
• address-family, page 17
• address, page 19
• admin-state-enable, page 20
• admin, page 22
• advertise-subnet, page 23
• aggregate-address, page 24
• allow-origin, page 25
• allow-self-as, page 26
• allow-writes, page 27
• allowed-self-as-count, page 28
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1
• application, page 29
• area default-cost, page 30
• area l3out, page 31
• area loopback, page 32
• area nssa, page 33
• area nssa default-information-originate, page 34
• area nssa no-redistribute, page 35
• area nssa translate, page 36
• area range, page 37
• area route-map, page 38
• area stub, page 39
• arp flooding, page 40
• asn, page 41
• attribute, page 42
• attribute match custom, page 43
• attribute match datacenter, page 44
• attribute match domain, page 45
• attribute match guest-os, page 46
• attribute match hypervisor-id, page 47
• attribute match ip, page 48
• attribute match mac, page 49
• attribute match vm-id, page 50
• attribute match vm-name, page 51
• attribute match vnic, page 52
• authenticate, page 53
• authentication-key, page 54
• auto-cost, page 55
• autonomous-system, page 56
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)2
A Commands
aaa authentication login consoleaaa authentication login console
Description: Configure console methods
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login console
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 3
A Commandsaaa authentication login console
aaa authentication login defaultaaa authentication login default
Description: Configure default methods
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)4
A Commandsaaa authentication login default
aaa authentication login domainaaa authentication login domain <WORD>
Description: Configure domain methods
Syntax:
Login domain nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 5
A Commandsaaa authentication login domain
aaa banneraaa banner <LINE>
Description: CLI informational banner to be displayed before user login (wrap with single quotes)
Syntax:
CLI informational banner to be displayed before user login (wrap withsingle quotes) (Max Size None)
LINE
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa banner <LINE>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)6
A Commandsaaa banner
aaa group server ldapaaa group server ldap <WORD>
Description: LDAP server group name.
Syntax:
LDAP server group nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa group server ldap <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 7
A Commandsaaa group server ldap
aaa group server radiusaaa group server radius <WORD>
Description: RADIUS server group name.
Syntax:
RADIUS server group nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa group server radius <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)8
A Commandsaaa group server radius
aaa group server tacacsplusaaa group server tacacsplus <WORD>
Description: TACACS+ server group name.
Syntax:
TACACS+ server group nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa group server tacacsplus <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 9
A Commandsaaa group server tacacsplus
aaa scvmm-certificateaaa scvmm-certificate <WORD>
Description: AAACertRule
Syntax:
Certificate nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa scvmm-certificate <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)10
A Commandsaaa scvmm-certificate
aaa user default-roleaaa user default-role <default-role-policy>
Description: Default role assigned by aaa-admin for remote authentication
Syntax:
<default-role-policy><default-role-policy>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# aaa user default-role <default-role-policy>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 11
A Commandsaaa user default-role
absoluteabsolute window <WORD>
Description: Absolute window configuration mode
Syntax:
Configure scheduler windowwindow
Window name (Max size 31)WORD
Command Mode: scheduler : Scheduler configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)12
A Commandsabsolute
access-groupaccess-group <WORD> <WORD>
Description: Apply an access-list on this subject
Syntax:
Name of the access-list to apply (Max Size 64)WORD
DirectionsWORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# access-group <WORD> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 13
A Commandsaccess-group
access-listaccess-list <WORD>
Description: Create access-list
Syntax:
Access-list Name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)14
A Commandsaccess-list
account-statusaccount-status <WORD>
Description: Set The status of the locally-authenticated user account.
Syntax:
status of the locally-authenticated user accountWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# account-status <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 15
A Commandsaccount-status
actionaction merge|replace
Description: Snapshot import action merge|replace
Syntax:
Merge with existing configurationmerge
Replace existing configurationreplace
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# action merge|replace
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)16
A Commandsaction
address-familyaddress-family ipv4|ipv6 unicast
Description: EIGRP Policy Address Family
Syntax:
Address Family IPv4ipv4
Address Family IPv6ipv6
Unicastunicast
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6 unicast
Description: Configure an address-family for peer
Syntax:
Configure IPv4 address-familyipv4
Configure IPv6 address-familyipv6
Configure Unicast sub-address-familyunicast
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast
address-family ipv4|ipv6 unicast
Description: Configure an address-family
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 17
A Commandsaddress-family
Configure IPv4 address-familyipv4
Configure IPv6 address-familyipv6
Configure unicast address-familyunicast
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)18
A Commandsaddress-family
addressaddress <A.B.C.D> [preferred]
Description: Configure the ip address for dns servers
Syntax:
IP address in format i.i.i.iA.B.C.D
(Optional) Configure the address to be preferredpreferred
Command Mode: dns : Configure default dns policy
Command Path:
# configure [['terminal', 't']](config)# dns(config-dns)# address <A.B.C.D> [preferred]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 19
A Commandsaddress
admin-state-enableadmin-state-enable
Description: Enable the state of the SSH communication service
Command Mode: ssh-service : SSH communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service(config-ssh-service)# admin-state-enable
admin-state-enable
Description: Enable the state of the TELNET communication service
Command Mode: telnet : TELNET communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet(config-telnet)# admin-state-enable
admin-state-enable
Description: Enable the state of the shellinabox communication service
Command Mode: shellinabox : SHELLINABOX communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# shellinabox(config-shellinabox)# admin-state-enable
admin-state-enable
Description: Enable the state of the HTTP communication service
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# admin-state-enable
admin-state-enable
Description: Enable the state of the HTTPS communication service
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)20
A Commandsadmin-state-enable
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# admin-state-enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 21
A Commandsadmin-state-enable
adminadmin enable
Description: Set admin state of syslog group
Syntax:
Enableenable
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# admin enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)22
A Commandsadmin
advertise-subnetadvertise-subnet
Description: Set OSPF Interface Policy Controls
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# advertise-subnet
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 23
A Commandsadvertise-subnet
aggregate-addressaggregate-address <IP-PREFIX/LEN> [as-set]
Description: Route summarization
Syntax:
Aggregate IPv4 address and mask lengthIP-PREFIX/LEN
(Optional) Autonomous system set path information and communityinformation
as-set
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# aggregate-address <IP-PREFIX/LEN> [as-set]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)24
A Commandsaggregate-address
allow-originallow-origin <WORD>
Description: The URL to return in the Access-Control-Allow-Origin HTTP header
Syntax:
The URL to return in the Access-Control-Allow-Origin HTTP header(Max Size 256)
WORD
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# allow-origin <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 25
A Commandsallow-origin
allow-self-asallow-self-as
Description: Accept as-path with my AS present in it
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# allow-self-as
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)26
A Commandsallow-self-as
allow-writesallow-writes
Description: Allow writes for the RBAC rule
Command Mode: rbac rule : Create RBAC rule, security domain users can read subtree starting at specificobject
Command Path:
# configure [['terminal', 't']](config)# rbac rule <DN> <WORD>(config-rule)# allow-writes
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 27
A Commandsallow-writes
allowed-self-as-countallowed-self-as-count <NUMBER>
Description: The number of occurrences of a local access service network
Syntax:
Number of occurrences of AS number, default is 3. Number rangefrom=1 to=10
<1-10>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# allowed-self-as-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)28
A Commandsallowed-self-as-count
applicationapplication <WORD>
Description: application configuration mode
Syntax:
Application name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 29
A Commandsapplication
area default-costarea <A.B.C.D|NUMBER> default-cost <0-16777215>
Description: Set OSPF default area cost
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Cost value<0-16777215>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> default-cost <0-16777215>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)30
A Commandsarea default-cost
area l3outarea <A.B.C.D|NUMBER> l3out <l3out name>
Description: Enable OSPF in the l3Out
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Configure ASN on an API configured L3Out<l3out name>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> l3out <l3out name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 31
A Commandsarea l3out
area loopbackarea <A.B.C.D|NUMBER> loopback <Loopback Ip Address>
Description: Configure OSPF on Loopback
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Loopback Ip<Loopback Ip Address>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> loopback <Loopback Ip Address>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)32
A Commandsarea loopback
area nssaarea <A.B.C.D|NUMBER> nssa
Description: Configure area as nssa
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 33
A Commandsarea nssa
area nssa default-information-originatearea <A.B.C.D|NUMBER> nssa default-information-originate [no-redistribute]
Description: Originate a default route
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
(Optional) No Redistribute area optionno-redistribute
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa default-information-originate[no-redistribute]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)34
A Commandsarea nssa default-information-originate
area nssa no-redistributearea <A.B.C.D|NUMBER> nssa no-redistribute [default-information-originate]
Description: Configure area as no-redistribute
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
(Optional) Originate a default routedefault-information-originate
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa no-redistribute[default-information-originate]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 35
A Commandsarea nssa no-redistribute
area nssa translatearea <A.B.C.D|NUMBER> nssa translate type7 suppress-fa
Description: Translate LSAs
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
From Type 7 to Type 5type7
Suppress forwarding address in translated LSAssuppress-fa
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> nssa translate type7 suppress-fa
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)36
A Commandsarea nssa translate
area rangearea <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]
Description: range
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Summarized IPIP-PREFIX/LENGTH
(Optional) Route costcost
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> range <IP-PREFIX/LENGTH> [cost <cost>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 37
A Commandsarea range
area route-maparea <A.B.C.D|NUMBER> route-map <WORD> out
Description: Set Route Map
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Route Map Name (Max Size 63)WORD
Apply policy to outgoing routesout
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)38
A Commandsarea route-map
area stubarea <A.B.C.D|NUMBER> stub
Description: Configure area as a stub
Syntax:
OSPF area ID<A.B.C.D|NUMBER>
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# area <A.B.C.D|NUMBER> stub
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 39
A Commandsarea stub
arp floodingarp flooding
Description: Enable ARP flooding
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# arp flooding
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)40
A Commandsarp flooding
asnasn <NUMBER>
Description: Configure BGP Autonomous System number
Syntax:
Number that uniquely identifies an autonomous system. Number rangefrom=1 to=4294967295
<1-4294967295>
Command Mode: bgp : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# bgp fabric(config-pod-bgp)# asn <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 41
A Commandsasn
attributeattribute <WORD>
Description: An LDAP endpoint attribute to be used as the CiscoAVPair
Syntax:
LDAP endpoint attribute (Max Size 63)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# attribute <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)42
A Commandsattribute
attribute match customattribute <WORD> match custom <WORD> <arg> <WORD>
Description: Configure a Custom attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
custom label nameWORD
arg
string to be matchedWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match custom <WORD> <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 43
A Commandsattribute match custom
attribute match datacenterattribute <WORD> match datacenter <arg> <WORD>
Description: Configure a Datacenter name attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match datacenter <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)44
A Commandsattribute match datacenter
attribute match domainattribute <WORD> match domain <arg> <WORD>
Description: Configure a Domain name attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match domain <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 45
A Commandsattribute match domain
attribute match guest-osattribute <WORD> match guest-os <arg> <WORD>
Description: Configure a Guest-OS attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match guest-os <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)46
A Commandsattribute match guest-os
attribute match hypervisor-idattribute <WORD> match hypervisor-id <arg> <WORD>
Description: Configure a Hypervisor ID attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match hypervisor-id <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 47
A Commandsattribute match hypervisor-id
attribute match ipattribute <WORD> match ip <ip-addr/mask>
Description: Configure a IP address attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
Full IP Address and mask<ip-addr/mask>
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match ip <ip-addr/mask>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)48
A Commandsattribute match ip
attribute match macattribute <WORD> match mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure a MAC address attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 49
A Commandsattribute match mac
attribute match vm-idattribute <WORD> match vm-id <arg> <WORD>
Description: Configure a VM identifier attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match vm-id <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)50
A Commandsattribute match vm-id
attribute match vm-nameattribute <WORD> match vm-name <arg> <WORD>
Description: Configure a VM name attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match vm-name <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 51
A Commandsattribute match vm-name
attribute match vnicattribute <WORD> match vnic <arg> <WORD>
Description: Configure a Vnic name attribute
Syntax:
uSeg attribute nameWORD
Match criteriamatch
arg
ValueWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# attribute <WORD> match vnic <> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)52
A Commandsattribute match vnic
authenticateauthenticate
Description: Configure authentication for the default ntp policy
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# authenticate
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 53
A Commandsauthenticate
authentication-keyauthentication-key <id> [md5 <md5>]
Description: Configure ntp authentication keys for the default ntp policy
Syntax:
Id for the authentication key. Number range from=1 to=65535id
(Optional) Configure the authentication key (Max Size 510)md5
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# authentication-key <id> [md5 <md5>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)54
A Commandsauthentication-key
auto-costauto-cost reference-bandwidth <NUMBER>
Description: Set OSPF Policy Bandwidth Reference
Syntax:
OSPF Policy Bandwidth Referencereference-bandwidth
BandwidthReferenceValue inMbps. Number range from=1 to=4000000<1-4000000>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# auto-cost reference-bandwidth <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 55
A Commandsauto-cost
autonomous-systemautonomous-system <NUMBER> [l3out <l3out>]
Description: Autonomous System Configuration for EIGRP
Syntax:
The autonomous system number. Number range from=1 to=65535<1-65535>
(Optional) Configure ASN on an API configured L3Outl3out
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# autonomous-system <NUMBER> [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)56
A Commandsautonomous-system
B Commands
• bandwidth, page 58
• basedn, page 59
• bash, page 60
• bfd, page 61
• bfd ip ipv6 authentication, page 62
• bfd ip ipv6 inherit, page 64
• bfd ip ipv6 tenant, page 65
• bgp, page 66
• binddn, page 67
• bpdu-filter, page 68
• bridge-domain, page 69
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 57
bandwidthbandwidth <NUMBER>
Description: Set the desired bandwidth to police to
Syntax:
Bandwidth percentage guaranteed as %. Number range from=0 to=100<0-100>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# bandwidth <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)58
B Commandsbandwidth
basednbasedn <WORD>
Description: The LDAP base DN for user lookup in the LDAP directory tree
Syntax:
user lookup in LDAP directory tree (Max Size 127)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# basedn <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 59
B Commandsbasedn
bashbash
Description: bash shell for unix commands
Command Mode: exec : Exec Mode
Command Path:
# bash
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)60
B Commandsbash
bfdbfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# bfd enable
bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# bfd enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 61
B Commandsbfd
bfd ip ipv6 authenticationbfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Description: Configure BFD authentication
Syntax:
IPv4ip
IPv6ipv6
Configure Keyed SHA1 authenticationkeyed-sha1
Configure authentication key IDkeyid
Authentication key ID. Number range from=1 to=255<keyid>
Configure shared authentication keykey
Shared authentication key (Max Size 20)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Description: Configure BFD authentication
Syntax:
IPv4ip
IPv6ipv6
Configure Keyed SHA1 authenticationkeyed-sha1
Configure authentication key IDkeyid
Authentication key ID. Number range from=1 to=255<keyid>
Configure shared authentication keykey
Shared authentication key (Max Size 20)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)62
B Commandsbfd ip ipv6 authentication
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 authentication keyed-sha1 keyid <NUMBER> key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 63
B Commandsbfd ip ipv6 authentication
bfd ip ipv6 inheritbfd ip|ipv6 inherit interface-policy <WORD>
Description: Inherit BFD interface template policy
Syntax:
IPv4ip
IPv6ipv6
Associate the interface with a BFD interface policyinterface-policy
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>
bfd ip|ipv6 inherit interface-policy <WORD>
Description: Inherit BFD interface template policy
Syntax:
IPv4ip
IPv6ipv6
Associate the interface with a BFD interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 inherit interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)64
B Commandsbfd ip ipv6 inherit
bfd ip ipv6 tenantbfd ip|ipv6 tenant mode
Description: Enable BFD Tenant Mode
Syntax:
IPv4ip
IPv6ipv6
Modemode
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# bfd ip|ipv6 tenant mode
bfd ip|ipv6 tenant mode
Description: Enable BFD Tenant Mode
Syntax:
IPv4ip
IPv6ipv6
Modemode
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# bfd ip|ipv6 tenant mode
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 65
B Commandsbfd ip ipv6 tenant
bgpbgp fabric
Description: Border Gateway Protocol (BGP)
Syntax:
Fabric BGP configurationfabric
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# bgp fabric
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)66
B Commandsbgp
binddnbinddn <WORD>
Description: The LDAP bind DN for user lookup in the LDAP directory tree
Syntax:
user lookup in LDAP directory tree (Max Size 127)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# binddn <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 67
B Commandsbinddn
bpdu-filterbpdu-filter
Description: Enable BPDU filter for extended chassis ports
Command Mode: spanning-tree : STP MST configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# bpdu-filter
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)68
B Commandsbpdu-filter
bridge-domainbridge-domain <WORD>
Description: Configuration for bridge-domain
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>
bridge-domain member <WORD>
Description: Bind the EPG to a bridge-domain
Syntax:
Bind the EPG to a bridge-domainmember
bridge-domain to associate (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# bridge-domain member <WORD>
bridge-domain <WORD>
Description: Bind the EPG to a bridge-domain
Syntax:
bridge domain associated with epg suggestion use "inb"WORD
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 69
B Commandsbridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# bridge-domain <WORD>
bridge-domain member <WORD>
Description: Bind the EPG to a bridge-domain
Syntax:
Bind the EPG to a bridge-domainmember
bridge-domain to associate (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# bridge-domain member <WORD>
bridge-domain tenant <tenant> name <name>
Description: Configure Bridge Domain For a L4-L7 Graph Connector.
Syntax:
Tenant in which the bridge domain is availabletenant
Tenant in which the bridge domain is available<tenant>
Bridge domain namename
Name of bd<name>
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# bridge-domain tenant <tenant> name <name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)70
B Commandsbridge-domain
C Commands
• callhome, page 73
• catalog-version, page 74
• cdp, page 75
• cert-chain, page 78
• cert, page 79
• certificate, page 80
• channel-group, page 81
• channel-mode, page 83
• ciphers, page 86
• clear-encryption-key, page 87
• clear-pwd-history, page 88
• clear endpoints, page 89
• clear snapshot file, page 90
• clear snapshot job, page 91
• clear techsupport controllers, page 92
• clear techsupport switch, page 93
• clear troubleshoot epext session report, page 94
• clear troubleshoot eptoep session report, page 95
• clock display-format, page 96
• clock show-offset, page 97
• clock timezone, page 98
• cluster-device, page 99
• cluster-device query-device-health, page 100
• cluster-device query-device-statistics, page 101
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 71
• cluster-device query-device-validation, page 102
• cluster-interface, page 103
• comm-policy, page 104
• configure-avs, page 105
• configure-dvs, page 106
• configure, page 107
• connection intra service, page 108
• connection terminal, page 109
• connector, page 110
• console, page 111
• contract-id, page 112
• contract, page 113
• contract consumer, page 114
• contract deny, page 117
• contract enforce, page 119
• contract provider, page 120
• controller-group, page 123
• controller, page 124
• cost, page 125
• country, page 126
• crypto aes, page 127
• crypto ca, page 128
• crypto keyring, page 129
• crypto webtoken, page 130
• csr, page 131
• customer-id, page 132
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)72
C Commands
callhomecallhome common
Description: Callhome common policy configuration mode
Syntax:
Callhome common policy configuration modecommon
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# callhome common
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 73
C Commandscallhome
catalog-versioncatalog-version <version>
Description: Change catalog version
Syntax:
firmware version<version>
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# catalog-version <version>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)74
C Commandscatalog-version
cdpcdp enable|default
Description: Configure CDP parameters on DVS uplink ports
Syntax:
Enable CDPenable
Remove CDP override policydefault
Command Mode: configure-dvs : Configure a VMware Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs(config-vmware-dvs)# cdp enable|default
cdp enable|default
Description: Configure CDP parameters on AVS uplink ports
Syntax:
Enable CDPenable
Remove CDP override policydefault
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# cdp enable|default
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: template policy-group : Configure Policy Group Parameters
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 75
C Commandscdp
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)76
C Commandscdp
(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# cdp enable
cdp enable
Description: Configure CDP interface parameters
Syntax:
Configure CDP parametersenable
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# cdp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 77
C Commandscdp
cert-chaincert-chain <WORD>
Description: Set The PEM-encoded chain of trust from the trustpoint to a trusted root authority.
Syntax:
The PEM-encoded chain of trust from the trustpoint to a trusted rootauthority
<WORD>
Command Mode: crypto ca : Configure certificate authority related information
Command Path:
# configure [['terminal', 't']](config)# crypto ca <WORD>(config-ca)# cert-chain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)78
C Commandscert-chain
certcert <CERTIFICATE>
Description: Provide a certificate, that contains public key and signed information.
Syntax:
Provide a certificate in quotes, that contains public key and signedinformation
<CERTIFICATE>
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# cert <CERTIFICATE>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 79
C Commandscert
certificatecertificate <WORD>
Description: Create AAA user certificate in X.509 format.
Syntax:
Name for the user certificateWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# certificate <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)80
C Commandscertificate
channel-groupchannel-group <WORD> [vpc]
Description: Create Port Channel
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Configure channel-group as VPCvpc
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# channel-group <WORD> [vpc]
channel-group <WORD> [vpc]
Description: Configure Port Channel on Fex
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Create the channel-group as a VPCvpc
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# channel-group <WORD> [vpc]
channel-group <WORD> [vpc]
Description: Associate a Channel Group to this Interface
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
(Optional) Create the channel-group as a VPCvpc
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 81
C Commandschannel-group
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# channel-group <WORD> [vpc]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)82
C Commandschannel-group
channel-modechannel-mode on|active|passive|mac-pinning
Description: Configure LACP mode override on DVS uplink ports
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: configure-dvs : Configure a VMware Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs(config-vmware-dvs)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure LACP mode override on AVS uplink ports
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# channel-mode on|active|passive|mac-pinning
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 83
C Commandschannel-mode
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# channel-mode on|active|passive|mac-pinning
channel-mode on|active|passive|mac-pinning
Description: Configure channeling mode
Syntax:
Set channeling mode to ON (static)on
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)84
C Commandschannel-mode
Set channeling mode to ACTIVEactive
Set channeling mode to PASSIVEpassive
Set channeling mode to MAC-PINNINGmac-pinning
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# channel-mode on|active|passive|mac-pinning
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 85
C Commandschannel-mode
ciphersciphers <WORD>
Description: HTTPS cipher suite
Syntax:
Provide a valid cipher nameWORD
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ciphers <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)86
C Commandsciphers
clear-encryption-keyclear-encryption-key
Description: Clears AES encryption key
Command Mode: crypto aes : AES encryption configuration
Command Path:
# configure [['terminal', 't']](config)# crypto aes(config-aes)# clear-encryption-key
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 87
C Commandsclear-encryption-key
clear-pwd-historyclear-pwd-history
Description: Clears the password history of a locally-authenticated user
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# clear-pwd-history
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)88
C Commandsclear-pwd-history
clear endpointsclear endpoints leaf <node-id> tenant <tenant-name> bridge-domain <bd-name> vlan <NUMBER>
Description: Clear endpoints
Syntax:
Leaf Numberleaf
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
node-id
Tenant Hosting the endpointstenant
Tenant Hosting the endpoints (Max Size 63)tenant-name
Bridge-Domain Hosting the endpointsbridge-domain
Bridge-Domain Hosting the endpoints (Max Size 64)bd-name
The encapsulation VLAN Hosting the endpointsvlan
The number of the encapsulation VLAN, from 1 to 4094. For example,for vlan-23 you enter 23 in this field.
<1-4094>
Command Mode: exec : Exec Mode
Command Path:
# clear endpoints leaf <WORD> tenant <WORD> bridge-domain <WORD> vlan <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 89
C Commandsclear endpoints
clear snapshot fileclear snapshot file <WORD>
Description: Remove snapshot file
Syntax:
Snapshot file nameWORD
Command Mode: exec : Exec Mode
Command Path:
# clear snapshot file <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)90
C Commandsclear snapshot file
clear snapshot jobclear snapshot job <WORD>
Description: Remove snapshot job
Syntax:
Snapshot job nameWORD
Command Mode: exec : Exec Mode
Command Path:
# clear snapshot job <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 91
C Commandsclear snapshot job
clear techsupport controllersclear techsupport controllers <NUMBER> <WORD>
Description: Clear techsupport status for controllers
Syntax:
Controller id. Number range from=1 to=32<1-32>
Techsupport collection timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear techsupport controllers <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)92
C Commandsclear techsupport controllers
clear techsupport switchclear techsupport switch <NUMBER> <WORD>
Description: Clear techsupport status for switch
Syntax:
Switch id. Number range from=101 to=4000<101-4000>
Techsupport collection timeWORD
Command Mode: exec : Exec Mode
Command Path:
# clear techsupport switch <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 93
C Commandsclear techsupport switch
clear troubleshoot epext session reportclear troubleshoot epext session <ession_name> report
Description: Remove all non-pending reports of a troubleshoot session
Syntax:
sessionsession
Session nameession_name
Command Mode: exec : Exec Mode
Command Path:
# clear troubleshoot epext session <ession_name> report
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)94
C Commandsclear troubleshoot epext session report
clear troubleshoot eptoep session reportclear troubleshoot eptoep session <session_name> report
Description: Remove all non-pending reports of a troubleshoot session
Syntax:
sessionsession
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# clear troubleshoot eptoep session <session_name> report
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 95
C Commandsclear troubleshoot eptoep session report
clock display-formatclock display-format local|utc
Description: Configure Clock Display Format
Syntax:
Local display formatlocal
UTC display formatutc
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# clock display-format local|utc
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)96
C Commandsclock display-format
clock show-offsetclock show-offset enable
Description: Enable/Disable Display of the Offset
Syntax:
Enable/Disable Display of the Offset from UTCenable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# clock show-offset enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 97
C Commandsclock show-offset
clock timezoneclock timezone <timeZone>
Description: Configure clock timezone
Syntax:
The Timezone SelectiontimeZone
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# clock timezone <timeZone>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)98
C Commandsclock timezone
cluster-devicecluster-device <WORD> [vcenter <WORD>] [vm <WORD>]
Description: Configure L4-L7 Cluster Device
Syntax:
device name (Max Size 64)WORD
(Optional) vcenter name (Max Size 64)WORD
(Optional) vm name (Max Size 128)WORD
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 99
C Commandscluster-device
cluster-device query-device-healthcluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-health
Description: Re-query for Device Health
Syntax:
device name (Max Size 64)WORD
(Optional) vcenter name (Max Size 64)WORD
(Optional) vm name (Max Size 128)WORD
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-health
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)100
C Commandscluster-device query-device-health
cluster-device query-device-statisticscluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-statistics
Description: Re-query for Device Statistics
Syntax:
device name (Max Size 64)WORD
(Optional) vcenter name (Max Size 64)WORD
(Optional) vm name (Max Size 128)WORD
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-statistics
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 101
C Commandscluster-device query-device-statistics
cluster-device query-device-validationcluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-validation
Description: Re-query for Device Validation
Syntax:
device name (Max Size 64)WORD
(Optional) vcenter name (Max Size 64)WORD
(Optional) vm name (Max Size 128)WORD
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] query-device-validation
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)102
C Commandscluster-device query-device-validation
cluster-interfacecluster-interface <WORD> [vlan <NUMBER>]
Description: Configure L4-L7 Cluster Interface
Syntax:
Cluster interface name (Max Size 16)WORD
(Optional) Static Encap/VLAN to user for this cluster interface. Numberrange from=1 to=4094
<vlan>
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 103
C Commandscluster-interface
comm-policycomm-policy <WORD>
Description: Configure any communication policy, ssh/telnet/shellinabox/http/https
Syntax:
Provide a communication policy nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)104
C Commandscomm-policy
configure-avsconfigure-avs
Description: Configure a VMware Domain as AVS (N1K) type
Command Mode: vmware-domain : Create a VMM VMware Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 105
C Commandsconfigure-avs
configure-dvsconfigure-dvs
Description: Configure a VMware Domain as DVS type
Command Mode: vmware-domain : Create a VMM VMware Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)106
C Commandsconfigure-dvs
configureconfigure [['terminal', 't']]
Description: Configuration Mode
Syntax:
(Optional) configure using terminalterminal
(Optional) configure using terminalterminal
Command Mode: exec : Exec Mode
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 107
C Commandsconfigure
connection intra serviceconnection <WORD> intra_service service1 <WORD> connector1 <WORD> service2 <WORD> connector2<WORD>
Description: Configure l4l7 connection between service nodes
Syntax:
Connection name (Max Size 64)WORD
Service node 1service1
service-node-1 name (Max Size 64)WORD
Connector on service node 1 that connects to the connectionconnector1
service-node-1 connector name (Max Size 64)WORD
Service node 2service2
service-node-2 name (Max Size 64)WORD
Connector on service node 2 that connects to the connectionconnector2
service-node-2 connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> intra_service service1 <WORD> connector1 <WORD> service2<WORD> connector2 <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)108
C Commandsconnection intra service
connection terminalconnection <WORD> terminal provider|consumer service <WORD> connector <WORD>
Description: Configure l4l7 connection to terminal
Syntax:
Connection name (Max Size 64)WORD
Provider terminalprovider
Consumer terminalconsumer
Service node that connects to a terminal nodeservice
service node name (Max Size 64)WORD
Connector on the service node that connects to a terminal nodeconnector
connector name (Max Size 64)WORD
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# connection <WORD> terminal provider|consumer service <WORD> connector <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 109
C Commandsconnection terminal
connectorconnector <WORD> [cluster-interface <WORD>]
Description: Configure Connector for a Service Node
Syntax:
Connector name (Max Size 64)WORD
(Optional) Cluster Interface name (Max Size 16)WORD
Command Mode: service : Configure L4-L7 Service
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)110
C Commandsconnector
consoleconsole [severity severity <severity-value>]
Description: Enable the logging to console(switches only)
Syntax:
(Optional) The severity level for the logsseverity <severity-value>
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# console [severity severity <severity-value>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 111
C Commandsconsole
contract-idcontract-id <WORD>
Description: Service contract id of the customer
Syntax:
The contract id (Max Size 512) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# contract-id <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)112
C Commandscontract-id
contractcontract <WORD> [type <type>]
Description: Configure binary contracts between Application EPGs
Syntax:
Name of the contract to create (Max Size 64)WORD
(Optional) whitelist (permit) or blacklist(deny) or oob-mgmt type ofcontract
type
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 113
C Commandscontract
contract consumercontract consumer <WORD> [qos-class <WORD>]
Description: Add the supplied contract to be consumed by any AEPg on this VRF
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract consumer <WORD> [qos-class <WORD>]
contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]
Description: Add a contract consumed by this AEPg, along with an optional list of subject labels
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class<WORD>]
contract consumer <contractName> [imported] [label <WORD>]
Description: Add a contract consumed by this EPG, along with an optional list of subject labels
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)114
C Commandscontract consumer
Whitelist contract to consume<contractName>
(Optional) Used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract consumer <contractName> [imported] [label <WORD>]
contract consumer <contractName> [label <label>]
Description: Add a contract consumed by this In-band Epg, along with an optional list of subject labels
Syntax:
link to contract name<contractName>
(Optional)label
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract consumer <contractName> [label <label>]
contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]
Description: Add a contract consumed by this EPG, along with an optional list of subject labels
Syntax:
Whitelist contract to consume (Max Size 64)WORD
(Optional) used for contracts imported from other tenantsimported
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 115
C Commandscontract consumer
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class<WORD>]
contract consumer <WORD> [imported]
Description: Add a consumer contract
Syntax:
Whitelist contract to consumeWORD
(Optional) Used for contracts imported from other tenantsimported
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# contract consumer <WORD> [imported]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)116
C Commandscontract consumer
contract denycontract deny <WORD>
Description: Attach a taboo contract to this AEPg
Syntax:
Name of the blacklist contract (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract deny <WORD>
contract deny <contractName>
Description: Attach a taboo contract to this EPG
Syntax:
Name of the blacklist contract<contractName>
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract deny <contractName>
contract deny <contractName>
Description: Attach a taboo contract to this InBand Epg
Syntax:
Name of the blacklist contract<contractName>
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 117
C Commandscontract deny
(config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract deny <contractName>
contract deny <WORD>
Description: Attach a taboo contract to this EPG
Syntax:
Name of the blacklist contract (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract deny <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)118
C Commandscontract deny
contract enforcecontract enforce [ingress] [egress]
Description: Add a policy enforcement
Syntax:
(Optional) Policy will be applied at the Ingress Nodeingress
(Optional) Policy will be applied at the Egress Nodeegress
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract enforce [ingress] [egress]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 119
C Commandscontract enforce
contract providercontract provider <WORD> [qos-class <WORD>]
Description: Add the supplied contract to be provided by any AEPg on this VRF
Syntax:
Whitelist contract provided (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# contract provider <WORD> [qos-class <WORD>]
contract provider <WORD> [label <WORD>] [qos-class <WORD>]
Description: Contract provided by this AEPg, along with an optional list of subject labels
Syntax:
Whitelist contract to provide (Max Size 64)WORD
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]
contract provider <contractName> [label <WORD>]
Description: Add a contract provided by this EPG, along with an optional list of subject labels
Syntax:
Whitelist contract to provide<contractName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)120
C Commandscontract provider
(Optional) Per-Contract label (Max Size 64)WORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# contract provider <contractName> [label <WORD>]
contract provider <contractName> [label <label>]
Description: Add a contract provided by this AEPg, along with an optional list of subject labels
Syntax:
link to contract name<contractName>
(Optional)label
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# contract provider <contractName> [label <label>]
contract provider <WORD> [label <WORD>] [qos-class <WORD>]
Description: Add a contract provided by this EPG, along with an optional list of subject labels
Syntax:
Whitelist contract to provide (Max Size 64)WORD
(Optional) Per-Contract label (Max Size 64)WORD
(Optional) Qos LevelWORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 121
C Commandscontract provider
contract provider <contractName>
Description: Add a contract provided by this AEPg, along with an optional list of subject labels
Syntax:
Name of the contract to be provided<contractName>
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# contract provider <contractName>
contract provider <WORD>
Description: Add a provider contract
Syntax:
Whitelist contract to provideWORD
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# contract provider <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)122
C Commandscontract provider
controller-groupcontroller-group
Description: Controller Upgrade Configuration Mode
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 123
C Commandscontroller-group
controllercontroller
Description: Configure Controller Node
Syntax:
arg
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# controller
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)124
C Commandscontroller
costcost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# cost <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 125
C Commandscost
countrycountry <WORD>
Description: Set The two-letter ISO code for the country where the organization is located.
Syntax:
The two-letter ISO code for the country where the organization is located<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# country <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)126
C Commandscountry
crypto aescrypto aes
Description: AES encryption configuration
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto aes
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 127
C Commandscrypto aes
crypto cacrypto ca <WORD>
Description: Configure certificate authority related information
Syntax:
Trustpoint label (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto ca <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)128
C Commandscrypto ca
crypto keyringcrypto keyring <WORD>
Description: A keyring mode to create and hold an SSL certificate
Syntax:
Provide a keyring nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 129
C Commandscrypto keyring
crypto webtokencrypto webtoken
Description: The cryptographic data used for generating and verifying web tokens.
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)130
C Commandscrypto webtoken
csrcsr
Description: A csr mode to create and hold an SSL certificate
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 131
C Commandscsr
customer-idcustomer-id <WORD>
Description: The customer id
Syntax:
The customer id (Max Size 512) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# customer-id <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)132
C Commandscustomer-id
D Commands
• data, page 135
• dead-interval, page 136
• debug log reset, page 137
• debug log set, page 138
• decommission controller, page 139
• decommission switch, page 140
• default-information, page 141
• default-originate, page 142
• deploy-epg tenant application epg type, page 143
• deploy-epg tenant application epg vlan, page 144
• deployment-mode, page 145
• descr, page 146
• description, page 147
• destination-profile, page 160
• destination, page 161
• destination destip, page 163
• destination interface, page 164
• destination tenant, page 165
• dhcp option, page 167
• dhcp relay policy, page 168
• dhparam, page 169
• direction, page 170
• disable-connected-check, page 173
• disable-peer-as-check, page 174
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 133
• distance, page 175
• dns, page 177
• dnssearchsuffix, page 178
• dnsservers, page 179
• dnssuffix, page 180
• domain, page 181
• dsr-vip, page 182
• dsr, page 183
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)134
D Commands
datadata <LINE>
Description: Set A user public key in PEM format.
Syntax:
user public key in PEM format in quotes (Max Size None)LINE
Command Mode: ssh-key : Update ssh key for the user for ssh authentication
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# ssh-key <WORD>(config-ssh-key)# data <LINE>
data <CERTIFICATE>
Description: Set PEM encoded certificate
Syntax:
PEM encoded certificate in quotesCERTIFICATE
Command Mode: certificate : Create AAA user certificate in X.509 format.
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# certificate <WORD>(config-certificate)# data <CERTIFICATE>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 135
D Commandsdata
dead-intervaldead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)136
D Commandsdead-interval
debug log resetdebug <node-name> <process> log reset
Description: Reset the log levels to default log level
Syntax:
Node name<node-name>
Process name<process>
Command Mode: exec : Exec Mode
Command Path:
# debug <node-name> <process> log reset
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 137
D Commandsdebug log reset
debug log setdebug <node-name> <process> log set <topic> <level>
Description: Set log level for a topic
Syntax:
Node name<node-name>
Process name<process>
Topic name<topic>
Level name<level>
Command Mode: exec : Exec Mode
Command Path:
# debug <node-name> <process> log set <topic> <level>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)138
D Commandsdebug log set
decommission controllerdecommission controller <NUMBER>
Description: Decommission controller
Syntax:
Controller ID. Number range from=1 to=32<1-32>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# decommission controller <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 139
D Commandsdecommission controller
decommission switchdecommission switch <NUMBER> [remove-from-controller]
Description: Decommission switch
Syntax:
Node ID. Number range from=101 to=4000<101-4000>
(Optional) Remove the switch from controller (optional)remove-from-controller
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# decommission switch <NUMBER> [remove-from-controller]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)140
D Commandsdecommission switch
default-informationdefault-information originate [always]
Description: Control origination of a default route
Syntax:
Originate a default routeoriginate
(Optional) Always advertise default routealways
Command Mode: vrf : Configure VRF information
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# default-information originate [always]
default-information originate [always]
Description: Control origination of a default route
Syntax:
Originate a default routeoriginate
(Optional) Always advertise default routealways
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# default-information originate [always]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 141
D Commandsdefault-information
default-originatedefault-originate
Description: Originate a default toward this peer
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# default-originate
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)142
D Commandsdefault-originate
deploy-epg tenant application epg typedeploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented
Description: Deploy micro-segmented AEPg on leaf
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
micro-segmented AEPgmicro-segmented
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> type micro-segmented
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 143
D Commandsdeploy-epg tenant application epg type
deploy-epg tenant application epg vlandeploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER> vlan-domain member<WORD>
Description: Deploy regular AEPg on leaf
Syntax:
Tenant hosting the AEPg to deploytenant
Tenant hosting the AEPg to deploy (Max Size 63)WORD
Application hosting the AEPg to deployapplication
Application Name (Max Size 64)WORD
AEPg to be deployed on the leafepg
EPg that uses the statically enabled Encap. (Max Size 64)WORD
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Vlan Domain for Encapsulation Vlanvlan-domain
Vlan Domain for Encapsulation Vlanmember
vlan-domain to use to validate encapsulation vlan. (Max Size 64)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# deploy-epg tenant <WORD> application <WORD> epg <WORD> vlan <NUMBER>vlan-domain member <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)144
D Commandsdeploy-epg tenant application epg vlan
deployment-modedeployment-mode <WORD>
Description: Set zone deployment mode
Syntax:
Zone Deployment ModeWORD
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# deployment-mode <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 145
D Commandsdeployment-mode
descrdescr <WORD>
Description: RADIUS server descr for authentication
Syntax:
descr for authentication (Max Size 128)<WORD>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# descr <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)146
D Commandsdescr
descriptiondescription <description>
Description: Add a description to a power supply redundancy policy
Syntax:
Power supply redundancy policy description string<description>
Command Mode: power : Create a power supply redundancy policy
Command Path:
# configure [['terminal', 't']](config)# power redundancy-policy <WORD>(config-power)# description <description>
description <LINE>
Description: Set description
Syntax:
Set description, use single quotes with spaces ex: 'my descr' (Max Size128)
LINE
CommandMode: rbac security-domain : Create AAA security domain for processing authentication requests.
Command Path:
# configure [['terminal', 't']](config)# rbac security-domain <WORD>(config-security-domain)# description <LINE>
description <WORD>
Description: The description of callhome destination-profile
Syntax:
The description (Max Size 128) surrounded by single quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 147
D Commandsdescription
(config-callhome-destnprof)# description <WORD>
description <WORD>
Description: Add switch-group description
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# description <WORD>
description <STRING>
Description: Configure STP description
Syntax:
DescriptionSTRING
Command Mode: region : STP MST region configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# description <STRING>
description <WORD>
Description: Description string, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)148
D Commandsdescription
(config-template-dhcp-relay)# description <WORD>
description <description>
Description: Update Policy-Group Template description
Syntax:
<description>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# description <description>
description <description>
Description: Update Port-Channel Template description
Syntax:
<description>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# description <description>
description <WORD>
Description: Add a description string to a tenant, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 149
D Commandsdescription
description <WORD>
Description: Add a description on a contract, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Contract description, surrounded by single quotes if with spaces ex:'My descr' (Max Size 128)
WORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# description <WORD>
description <WORD>
Description: Add a description on a subject, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Subject description, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# description <WORD>
description <WORD>
Description: Add a description on a vrf, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
VRF description, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)150
D Commandsdescription
(config-tenant-vrf)# description <WORD>
description <WORD>
Description: Add a description on an application, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# description <WORD>
description <WORD>
Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# description <WORD>
description <epgDescr>
Description: Add a description on an epg
Syntax:
<epgDescr>
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 151
D Commandsdescription
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# description <epgDescr>
description <WORD>
Description:Add a description on a bridge-domain, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Bridge-domain description, surrounded by single quotes if with spacesex: 'My descr' (Max Size 128)
WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# description <WORD>
description <WORD>
Description: Add a description on an epg, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# description <WORD>
description <epgDescr>
Description: Add a description on an epg
Syntax:
<epgDescr>
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)152
D Commandsdescription
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# description <epgDescr>
description <WORD>
Description: Description string, surrounded by single quotes if with spaces ex: 'My descr'
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# description <WORD>
description <LINE>
Description: Update igmp snooping policy description
Syntax:
IGMP snooping policy description, use single quotes with spaces ex:'my descr' (Max Size 128)
LINE
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# description <LINE>
description <LINE>
Description: Update Leaf Interface Profile description
Syntax:
Leaf-If-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 153
D Commandsdescription
Command Mode: leaf-interface-profile : Create Leaf Interface Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# description <LINE>
description <LINE>
Description: Update Leaf Interface Group description
Syntax:
Leaf-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# description <LINE>
description <LINE>
Description: Update Leaf Profile description
Syntax:
Leaf-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# description <LINE>
description <LINE>
Description: Update Leaf Group description
Syntax:
Leaf-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)154
D Commandsdescription
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# description <LINE>
description <LINE>
Description: Update Fex Profile description
Syntax:
Fex-Profile description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: fex-profile : Configure Fex Profile
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# description <LINE>
description <LINE>
Description: Update Fex Interface Group description
Syntax:
Fex-If-group description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# description <LINE>
description <LINE>
Description: Update interface vlan description
Syntax:
interface vlan description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 155
D Commandsdescription
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# description <LINE>
description <LINE>
Description: Update Interface description
Syntax:
Interface description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# description <LINE>
description <LINE>
Description: Update Port-Channel description
Syntax:
Port-Channel description, use single quotes with spaces ex: 'my descr'(Max Size 128)
LINE
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# description <LINE>
description <LINE>
Description: Update VPC description
Syntax:
VPC description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)156
D Commandsdescription
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 157
D Commandsdescription
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# description <LINE>
description <LINE>
Description: Add description to the session
Syntax:
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# description <LINE>
description <STRING>
Description: Configure schedule description
Syntax:
Scheduler descriptionSTRING
Command Mode: scheduler : Scheduler configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# description <STRING>
description <WORD>
Description: Add description for this server-group
Syntax:
Description (Max Size 128) surrounded by single quotesWORD
Command Mode: logging : Logging server group configuration mode
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)158
D Commandsdescription
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# description <WORD>
description <WORD>
Description: Add zone description
Syntax:
Description string, surrounded by single quotes if with spaces ex: 'Mydescr' (Max Size 128)
WORD
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 159
D Commandsdescription
destination-profiledestination-profile
Description: Configure destination profile Parameters
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)160
D Commandsdestination-profile
destinationdestination <WORD>
Description: Configure destination Parameters
Syntax:
The name (Max Size 64)WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>
destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>
Description: Configure monitor remote destination
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application nameapplication_name
epgepg
epg nameepg_name
destination IPdestination-ip
IP addressA.B.C.D
source IP prefixsource-ip-prefix
IP adddress prefixA.B.C.D/M
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 161
D Commandsdestination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>
Description: Configure monitor remote destination
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
destination IPdestination-ip
IP addressA.B.C.D
source IP prefixsource-ip-prefix
IP adddress prefixA.B.C.D/M
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)162
D Commandsdestination
destination destipdestination destip <A.B.C.D>
Description: Configure monitor remote destination
Syntax:
Destination IP addressA.B.C.D
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 163
D Commandsdestination destip
destination interfacedestination interface ethernet <ethernet> leaf <leaf Id>
Description: Configure monitor local destination
Syntax:
ethernetethernet
<ethernet><ethernet>
leafleaf
leaf Id<leaf Id>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination interface ethernet <ethernet> leaf <leaf Id>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)164
D Commandsdestination interface
destination tenantdestination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D>source-ip-prefix <A.B.C.D/M>
Description: Configure monitor remote destination
Syntax:
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
destination IPdestination-ip
IP addressA.B.C.D
source IP prefixsource-ip-prefix
IP adddress prefixA.B.C.D/M
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
destination tenant <WORD> application <WORD> epg <WORD> macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure monitor local destination
Syntax:
tenant name (Max Size 63)WORD
applicationapplication
application name (Max Size 64)WORD
epgepg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 165
D Commandsdestination tenant
epg name (Max Size 64)WORD
macmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination tenant <WORD> application <WORD> epg <WORD> macE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)166
D Commandsdestination tenant
dhcp optiondhcp option <WORD> id <NUMBER> data <WORD>
Description: Add or modify an existing DHCP option when relayed from the server to the client
Syntax:
Name of the option to add (Max Size 64)WORD
ID of the optionid
ID of the option. Number range from=0 to=255<0-255>
Body of the Option TLV as hex stringdata
Body of the Option TLV as hex string, surrounded by single quotes ex:'foo*' (Max Size 256)
WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# dhcp option <WORD> id <NUMBER> data <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 167
D Commandsdhcp option
dhcp relay policydhcp relay policy tenant|infra <WORD> [option <WORD>]
Description: Associate the BD with a DHCP Relay policy
Syntax:
Select DHCP policies from current Tenanttenant
Select DHCP policy from infrainfra
Name of the DHCP relay policy (Max Size 64)WORD
(Optional) Name of the DHCP option policy (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# dhcp relay policy tenant|infra <WORD> [option <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)168
D Commandsdhcp relay policy
dhparamdhparam <dhparam>
Description: Set the DH parameter used for HTTPS communication service
Syntax:
DH Param as comma separated values like val1,val2,..valNdhparam
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# dhparam <dhparam>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 169
D Commandsdhparam
directiondirection both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source interface ethernet : Configure monitor for ethernet access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>(config-monitor-access-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source interface port-channel : Configure monitor for port-channel interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>](config-monitor-access-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)170
D Commandsdirection
bothboth
rxrx
txtx
Command Mode: source interface vpc : Configure monitor for VPC interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>](config-monitor-access-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# direction both|rx|tx
direction both|rx|tx
Description:Monitor direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source application : Configure EPG as monitor source
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 171
D Commandsdirection
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# source application <application_name> epg <epg_name>(config-monitor-tenant-source)# direction both|rx|tx
direction both|rx|tx
Description: Configure monitor source direction
Syntax:
bothboth
rxrx
txtx
Command Mode: source : Configure monitor virtual source
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >](config-monitor-virtual-source)# direction both|rx|tx
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)172
D Commandsdirection
disable-connected-checkdisable-connected-check
Description: Disable check for directly connected peer
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# disable-connected-check
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 173
D Commandsdisable-connected-check
disable-peer-as-checkdisable-peer-as-check
Description: Disable checking of peer AS-number while advertising
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# disable-peer-as-check
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)174
D Commandsdisable-peer-as-check
distancedistance <NUMBER>
Description: Set OSPF Policy Preferred Administrative Distance
Syntax:
Distance Value. Number range from=1 to=255<1-255>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# distance <NUMBER>
distance <NUMBER> <NUMBER> <NUMBER>
Description: Configure BGP Address Family Distance Properties
Syntax:
The administrative distance of eBGP routes. Number range from=1to=255
<1-255>
The administrative distance of iBGP routes. Number range from=1to=255
<1-255>
The administrative distance of local routes. Number range from=1to=255
<1-255>
Command Mode: template bgp address-family : Configure Router BGP Address Family Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>(config-bgp-af)# distance <NUMBER> <NUMBER> <NUMBER>
distance <NUMBER> <NUMBER>
Description: Set EIGRP adminstrative distances
Syntax:
The administrative distance preference for internal routes. Number rangefrom=1 to=255
<1-255>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 175
D Commandsdistance
The administrative distance preference for external routes. Numberrange from=1 to=255
<1-255>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# distance <NUMBER> <NUMBER>
distance <NUMBER> <NUMBER>
Description: Set EIGRP adminstrative distances
Syntax:
The administrative distance preference for internal routes. Number rangefrom=1 to=255
<1-255>
The administrative distance preference for external routes. Numberrange from=1 to=255
<1-255>
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# distance <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)176
D Commandsdistance
dnsdns
Description: Configure default dns policy
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# dns
dns label <WORD>
Description: Add a DNS policy to the VRF
Syntax:
Dns policy to applylabel
Dns policy to apply (Max Size 64)WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# dns label <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 177
D Commandsdns
dnssearchsuffixdnssearchsuffix <suffix>
Description: Add DNS search suffix
Syntax:
suffixsuffix
Command Mode: microsoft : Configure static ip pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnssearchsuffix <suffix>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)178
D Commandsdnssearchsuffix
dnsserversdnsservers <DNS server list>
Description: Add dns servers
Syntax:
DNS server listDNS server list
Command Mode: microsoft : Configure static ip pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnsservers <DNS server list>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 179
D Commandsdnsservers
dnssuffixdnssuffix <suffix>
Description: Add dns suffix
Syntax:
suffixsuffix
Command Mode: microsoft : Configure static ip pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# dnssuffix <suffix>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)180
D Commandsdnssuffix
domaindomain <WORD>
Description: Create the AAA domain to which the user belongs.
Syntax:
Domain for the userWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>
domain <WORD> [default]
Description: Configure the domains for dns servers
Syntax:
Domain in the format^([a-zA-Z]|[a-zA-Z][a-zA-Z0-9]|[a-zA-Z][a-zA-Z0-9-.]{0,253}[a-zA-Z0-9])$
WORD
(Optional) Set the default domain for dns serversdefault
Command Mode: dns : Configure default dns policy
Command Path:
# configure [['terminal', 't']](config)# dns(config-dns)# domain <WORD> [default]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 181
D Commandsdomain
dsr-vipdsr-vip <WORD>
Description: Configure DSR VIP For a L4-L7 Graph Connector.
Syntax:
Enter VIP address (Max Size None)WORD
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# dsr-vip <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)182
D Commandsdsr-vip
dsrdsr virtual-ip-address <address> [description <description>]
Description: Add a DSR virtual IP address
Syntax:
Virtual IP address of load balancervirtual-ip-address
IP address<address>
(Optional) descriptiondescription
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# dsr virtual-ip-address <address> [description <description>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 183
D Commandsdsr
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)184
D Commandsdsr
E Commands
• ebgp-multihop, page 187
• echo-address, page 188
• echo-mode, page 189
• echo-rx-interval, page 190
• email-addr, page 191
• email-contact, page 192
• email, page 193
• enable-ssl, page 194
• encryption, page 195
• end, page 196
• endpoint, page 197
• endpoint loop-detect action bd-learn-disable, page 198
• endpoint loop-detect action port-disable, page 199
• endpoint loop-detect enable, page 200
• endpoint loop-detect factor, page 201
• endpoint loop-detect interval, page 202
• endpoint move-detection, page 203
• endpoint retention bounce-age-interval, page 204
• endpoint retention hold-interval, page 205
• endpoint retention local-age-interval, page 206
• endpoint retention move-frequency, page 207
• endpoint retention policy, page 208
• endpoint retention remote-age-interval, page 209
• enforce-subnet-learning, page 210
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 185
• epg, page 211
• eraseconfig, page 212
• errdisable recovery cause bpduguard, page 213
• errdisable recovery cause ep-move, page 214
• errdisable recovery cause mcp-loop, page 215
• errdisable recovery interval, page 216
• erspan-id, page 217
• exec, page 219
• exit, page 220
• expiration, page 221
• expires, page 222
• export, page 223
• external-l2, page 224
• external-l3, page 225
• external-l3 epg, page 226
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)186
E Commands
ebgp-multihopebgp-multihop <NUMBER>
Description: Specify multihop TTL for remote peer
Syntax:
EBGP TTL value. Number range from=1 to=255<1-255>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# ebgp-multihop <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 187
E Commandsebgp-multihop
echo-addressecho-address <arg>
Description: Configure BFD ECHO-SRC-ADDRESS value
Syntax:
arg
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# echo-address <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)188
E Commandsecho-address
echo-modeecho-mode enable
Description: Enable Echo mode
Syntax:
Enable Echo modeenable
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-mode enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 189
E Commandsecho-mode
echo-rx-intervalecho-rx-interval <NUMBER>
Description: Configure BFD ECHO-RX-INTERVAL value in milliseconds
Syntax:
BFD interval. Number range from=50 to=999<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# echo-rx-interval <NUMBER>
echo-rx-interval <NUMBER>
Description: Configure Echo Rx Interval in milliseconds
Syntax:
Echo Rx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# echo-rx-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)190
E Commandsecho-rx-interval
email-addremail-addr <WORD>
Description: Configure the e-mail address
Syntax:
The email address (Max Size None)WORD
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# email-addr <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 191
E Commandsemail-addr
email-contactemail-contact <WORD>
Description: The contact e-mail address
Syntax:
Contract e-mail address (Max Size 512)WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# email-contact <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)192
E Commandsemail-contact
emailemail <WORD>
Description: Set The email address of the locally-authenticated user.
Syntax:
email address of the locally-authenticated userWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# email <WORD>
email <WORD>
Description: Set The email address of the organization contact person.
Syntax:
email address (Max Size 40)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# email <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 193
E Commandsemail
enable-sslenable-ssl
Description: enabling an SSL connection with the LDAP provider
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# enable-ssl
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)194
E Commandsenable-ssl
encryptionencryption
Description: Enable AES Encryption
Command Mode: crypto aes : AES encryption configuration
Command Path:
# configure [['terminal', 't']](config)# crypto aes(config-aes)# encryption
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 195
E Commandsencryption
endend
Description: Exit to the exec mode
Command Mode: exec : Exec Mode
Command Path:
# end
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)196
E Commandsend
endpointendpoint retention <WORD>
Description: Specify an endpoint retention policy for this VRF
Syntax:
Specify an endpoint retention policy for this VRFretention
Endpoint Retention Policy (Max Size 64)WORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# endpoint retention <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 197
E Commandsendpoint
endpoint loop-detect action bd-learn-disableendpoint loop-detect action bd-learn-disable
Description: Configure EP Loop Protection Action to BD-Learn-Disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect action bd-learn-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)198
E Commandsendpoint loop-detect action bd-learn-disable
endpoint loop-detect action port-disableendpoint loop-detect action port-disable
Description: Configure EP Loop Protection Action to Port-Disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect action port-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 199
E Commandsendpoint loop-detect action port-disable
endpoint loop-detect enableendpoint loop-detect enable
Description: Enable/Disable Endpoint Loop-Detect Policy
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)200
E Commandsendpoint loop-detect enable
endpoint loop-detect factorendpoint loop-detect factor <NUMBER>
Description: Configure End Point Loop Detection Factor
Syntax:
End Point Loop ProtectionMultipication Factor. Number range from=1to=255
<1-255>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect factor <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 201
E Commandsendpoint loop-detect factor
endpoint loop-detect intervalendpoint loop-detect interval <NUMBER>
Description: Configure End Point Loop Detection Interval
Syntax:
End Point Loop Detection Interval. Number range from=30 to=300<30-300>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# endpoint loop-detect interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)202
E Commandsendpoint loop-detect interval
endpoint move-detectionendpoint move-detection <WORD>
Description: Endpoint Move detection Mode
Syntax:
Endpoint Move detection ModeWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint move-detection <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 203
E Commandsendpoint move-detection
endpoint retention bounce-age-intervalendpoint retention bounce-age-interval x in <0-0> or <150-65535>
Description: Set the bounce age interval for endpoints
Syntax:
Set the Bounce Age Interval, use 0 for infinitex in <0-0> or <150-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention bounce-age-interval x in <0-0> or <150-65535>
endpoint retention bounce-age-interval x in <0-0> or <150-65535>
Description: Set the bounce age interval for endpoints
Syntax:
Set the Bounce Age Interval, use 0 for infinitex in <0-0> or <150-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention bounce-age-interval x in<0-0> or <150-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)204
E Commandsendpoint retention bounce-age-interval
endpoint retention hold-intervalendpoint retention hold-interval <NUMBER>
Description: Set the hold interval for endpoints
Syntax:
Set the Hold Interval. Number range from=5 to=65535<5-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention hold-interval <NUMBER>
endpoint retention hold-interval <NUMBER>
Description: Set the hold interval for endpoints
Syntax:
Set the Hold Interval. Number range from=5 to=65535<5-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention hold-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 205
E Commandsendpoint retention hold-interval
endpoint retention local-age-intervalendpoint retention local-age-interval x in <0-0> or <120-65535>
Description: Set the local endpoint age interval
Syntax:
Set the local endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention local-age-interval x in <0-0> or <120-65535>
endpoint retention local-age-interval x in <0-0> or <120-65535>
Description: Set the local endpoint age interval
Syntax:
Set the local endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention local-age-interval x in<0-0> or <120-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)206
E Commandsendpoint retention local-age-interval
endpoint retention move-frequencyendpoint retention move-frequency <NUMBER>
Description: Set the move frequency
Syntax:
Set the move frequency. Number range from=0 to=65535<0-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention move-frequency <NUMBER>
endpoint retention move-frequency <NUMBER>
Description: Set the move frequency
Syntax:
Set the move frequency. Number range from=0 to=65535<0-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention move-frequency <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 207
E Commandsendpoint retention move-frequency
endpoint retention policyendpoint retention policy <WORD>
Description: Associate the BD with an endpoint retention policy
Syntax:
Name of the endpoint retention policy to set (Max Size 64)WORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)208
E Commandsendpoint retention policy
endpoint retention remote-age-intervalendpoint retention remote-age-interval x in <0-0> or <120-65535>
Description: Set the remote endpoint age interval
Syntax:
Remote endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# endpoint retention remote-age-interval x in <0-0> or <120-65535>
endpoint retention remote-age-interval x in <0-0> or <120-65535>
Description: Set the remote endpoint age interval
Syntax:
Remote endpoint age interval, use 0 for infinitex in <0-0> or <120-65535>
Command Mode: template endpoint retention policy : Configure an endpoint retention policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>(config-tenant-template-endpoint-retention)# endpoint retention remote-age-interval x in<0-0> or <120-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 209
E Commandsendpoint retention remote-age-interval
enforce-subnet-learningenforce-subnet-learning
Description: Subnet learning enforcement
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# enforce-subnet-learning
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)210
E Commandsenforce-subnet-learning
epgepg <WORD> [type <WORD>]
Description: AEPg configuration mode
Syntax:
Application EPG name (Max Size 64)WORD
(Optional) Specify EPG typeWORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 211
E Commandsepg
eraseconfigeraseconfig
Description: Erase config and reboot
Command Mode: exec : Exec Mode
Command Path:
# eraseconfig
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)212
E Commandseraseconfig
errdisable recovery cause bpduguarderrdisable recovery cause bpduguard
Description: Enable timer to recover from BPDU Guard error disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery cause bpduguard
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 213
E Commandserrdisable recovery cause bpduguard
errdisable recovery cause ep-moveerrdisable recovery cause ep-move
Description: Enable timer to recover from End Point Move error disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery cause ep-move
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)214
E Commandserrdisable recovery cause ep-move
errdisable recovery cause mcp-looperrdisable recovery cause mcp-loop
Description: Enable timer to recover from MCP Loop error disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery cause mcp-loop
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 215
E Commandserrdisable recovery cause mcp-loop
errdisable recovery intervalerrdisable recovery interval <NUMBER>
Description: Configure Error Disable Recovery Interval
Syntax:
Timer-interval (sec). Number range from=30 to=65535<30-65535>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# errdisable recovery interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)216
E Commandserrdisable recovery interval
erspan-iderspan-id <id>
Description: Erspan Id
Syntax:
erspan Id. Number range from=1 to=1023id
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# erspan-id <id>
erspan-id <id>
Description: Erspan Id
Syntax:
erspan Id. Number range from=1 to=1023id
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# erspan-id <id>
erspan-id <arg>
Description: Erspan Id
Syntax:
erspan Id. Number range from=1 to=1023arg
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 217
E Commandserspan-id
(config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# erspan-id <>
erspan-id <arg>
Description: Configure ERSPAN ID
Syntax:
ERSPAN ID. Number range from=1 to=1023arg
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# erspan-id <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)218
E Commandserspan-id
execexec
Description: Exec Mode
Command Mode: None
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 219
E Commandsexec
exitexit
Description: Exit from current mode
Command Mode: exec : Exec Mode
Command Path:
# exit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)220
E Commandsexit
expirationexpiration <DATE>
Description: If expires enabled, Set expiration date of locally-authenticated user account.
Syntax:
UTC Date format (YYYY-MM-DDTHH:MM:SS.mmm[+-]hh:mm)DATE
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# expiration <DATE>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 221
E Commandsexpiration
expiresexpires
Description: Enable expiry for locally-authenticated user account
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# expires
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)222
E Commandsexpires
exportexport to tenant <WORD> [as <WORD>]
Description: Export a contract to another tenant
Syntax:
Tenant to export the command toto
Tenant to export the command totenant
Tenant to export the command to (Max Size 63)WORD
(Optional) New name under which the contract will be known (MaxSize 64)
WORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# export to tenant <WORD> [as <WORD>]
export map <WORD>
Description: VRF export
Syntax:
Route-map for inter VRF route leakmap
Route Map Name (Max Size 63)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# export map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 223
E Commandsexport
external-l2external-l2 epg <WORD>
Description: L2 external EPG creation/configuration
Syntax:
L2 external EPG nameepg
L2 external EPG name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)224
E Commandsexternal-l2
external-l3external-l3 epg <WORD>
Description: External L3 EPG to associate
Syntax:
Specify the external EPGepg
External L3 EPG nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# external-l3 epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 225
E Commandsexternal-l3
external-l3 epgexternal-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
Description: External L3 EPG configuration mode
Syntax:
External L3 EPG name (Max Size 49)WORD
(Optional) External L3 EPG for Out of bandoob-mgmt
(Optional) Configure external-l3 epg on an API configured L3Outl3out
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)226
E Commandsexternal-l3 epg
F Commands
• fabric clear, page 228
• fabric show, page 229
• fex-interface-group, page 230
• fex-profile, page 231
• fex, page 232
• file, page 233
• filter, page 234
• filter tenant bd, page 236
• filter tenant vrf, page 237
• firewall-logging, page 238
• firewall, page 239
• firmware-version, page 240
• firmware, page 241
• firmware repository add, page 242
• firmware repository delete, page 243
• firmware upgrade controller-group, page 244
• firmware upgrade switch-group, page 245
• first-file, page 246
• first-name, page 247
• format, page 248
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 227
fabric clearfabric <nodes> clear <scope>
Description: clear switch information
Syntax:
node list<nodes>
switch command<scope>
Command Mode: exec : Exec Mode
Command Path:
# fabric <nodes> clear <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)228
F Commandsfabric clear
fabric showfabric <nodes> show <scope>
Description: show switch information
Syntax:
node list<nodes>
switch command<scope>
Command Mode: exec : Exec Mode
Command Path:
# fabric <nodes> show <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 229
F Commandsfabric show
fex-interface-groupfex-interface-group <WORD>
Description: Configure Fex Interface Group
Syntax:
Fex Interface Group Name (Max Size 64)WORD
Command Mode: fex-profile : Configure Fex Profile
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)230
F Commandsfex-interface-group
fex-profilefex-profile <WORD>
Description: Configure Fex Profile
Syntax:
Fex Profile Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 231
F Commandsfex-profile
fexfex associate <NUMBER> template <WORD>
Description: Configure Fex on the Interface
Syntax:
Associate the port to a FEXassociate
Fex Number. Number range from=101 to=164NUMBER
Associate a templatetemplate
Fex Template Name (Max Size 64)WORD
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# fex associate <NUMBER> template <WORD>
fex associate <arg>
Description: Configure Fex on the Interface
Syntax:
Associate the port to a FEXassociate
Fex Number. Number range from=101 to=164arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# fex associate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)232
F Commandsfex
filefile <FILENAME>
Description: Snapshot file name
Syntax:
Snapshot file nameFILENAME
Command Mode: snapshot download : Configuration snapshot download setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot download <WORD>(config-download)# file <FILENAME>
file <FILENAME>
Description: Snapshot file name
Syntax:
Snapshot file nameFILENAME
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# file <FILENAME>
file <FILENAME>
Description: Snapshot file name
Syntax:
Snapshot file nameFILENAME
Command Mode: snapshot upload : Configuration snapshot upload setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot upload <WORD>(config-upload)# file <FILENAME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 233
F Commandsfile
filterfilter <WORD>
Description: Set the LDAP filter to be used in a user search
Syntax:
filter used in user search (Max Size 63)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# filter <WORD>
filter tenant <tenant_name> application <application_name> epg <epg_name>
Description: EPG filter
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: source interface ethernet : Configure monitor for ethernet access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>(config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>
filter tenant <tenant_name> application <application_name> epg <epg_name>
Description: EPG filter
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)234
F Commandsfilter
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: source interface port-channel : Configure monitor for port-channel interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>](config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>
filter tenant <tenant_name> application <application_name> epg <epg_name>
Description: EPG filter
Syntax:
tenanttenant
tenant name (Max Size 63)tenant_name
applicationapplication
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: source interface vpc : Configure monitor for VPC interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>](config-monitor-access-source)# filter tenant <tenant_name> application <application_name>epg <epg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 235
F Commandsfilter
filter tenant bdfilter tenant <tenant_name> bd <bd_name>
Description: BD filter
Syntax:
tenanttenant
tenant nametenant_name
BD namebd_name
Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# filter tenant <tenant_name> bd <bd_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)236
F Commandsfilter tenant bd
filter tenant vrffilter tenant <tenant_name> vrf <vrf_name>
Description: VRF filter
Syntax:
tenanttenant
tenant nametenant_name
vrf namevrf_name
Command Mode: source interface ethernet : Configure monitor for ethernet fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>(config-monitor-fabric-source)# filter tenant <tenant_name> vrf <vrf_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 237
F Commandsfilter tenant vrf
firewall-loggingfirewall-logging server-group <WORD> [severity severity <severity-info>] [polling-interval <polling-interval>]
Description: Configure firewall-logging on AVS
Syntax:
Specify server group nameserver-group
Logging server-group name (Max Size 64)WORD
(Optional) Specify severity infoseverity <severity-info>
(Optional) Specify polling interval time in seconds. Number rangefrom=60 to=86400
polling-interval
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# firewall-logging server-group <WORD> [severity severity <severity-info>][polling-interval <polling-interval>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)238
F Commandsfirewall-logging
firewallfirewall mode enabled|disabled|learning
Description: Configure firewall mode on AVS
Syntax:
firewall modemode
Enabled modeenabled
Disabled modedisabled
Learning modelearning
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# firewall mode enabled|disabled|learning
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 239
F Commandsfirewall
firmware-versionfirmware-version <version>
Description: Set target firmware version
Syntax:
firmware version<version>
Command Mode: controller-group : Controller Upgrade Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group(config-firmware-controller)# firmware-version <version>
firmware-version <version>
Description: Set target firmware version
Syntax:
firmware version<version>
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# firmware-version <version>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)240
F Commandsfirmware-version
firmwarefirmware
Description: Firmware upgrade configuration Mode
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 241
F Commandsfirmware
firmware repository addfirmware repository add <WORD>
Description: Add firmware image to repository
Syntax:
Firmware image filename(absolute path)WORD
Command Mode: exec : Exec Mode
Command Path:
# firmware repository add <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)242
F Commandsfirmware repository add
firmware repository deletefirmware repository delete <WORD>
Description: Remove firmware image from repository
Syntax:
Firmware image nameWORD
Command Mode: exec : Exec Mode
Command Path:
# firmware repository delete <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 243
F Commandsfirmware repository delete
firmware upgrade controller-groupfirmware upgrade controller-group
Description: Trigger controller-group upgrade
Command Mode: exec : Exec Mode
Command Path:
# firmware upgrade controller-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)244
F Commandsfirmware upgrade controller-group
firmware upgrade switch-groupfirmware upgrade switch-group <WORD>
Description: Trigger switch-group upgrade
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# firmware upgrade switch-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 245
F Commandsfirmware upgrade switch-group
first-filefirst-file <FILENAME>
Description: First snapshot file name
Syntax:
First snapshot file nameFILENAME
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# first-file <FILENAME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)246
F Commandsfirst-file
first-namefirst-name <WORD>
Description: Set the first name of the locally-authenticated user.
Syntax:
first name (Max Size 32)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# first-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 247
F Commandsfirst-name
formatformat xml|short-txt|aml
Description: Configure the format of the message
Syntax:
Xmlxml
Short-txtshort-txt
Amlaml
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# format xml|short-txt|aml
format xml|json
Description: Snapshot format: xml or json
Syntax:
XML formatxml
JSON formatjson
Command Mode: snapshot export : Configuration export setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# format xml|json
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)248
F Commandsformat
G Commands
• graceful-restart-helper, page 250
• graceful-restart, page 251
• group, page 252
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 249
graceful-restart-helpergraceful-restart-helper
Description: Configure BGP Policy Graceful Restart Helper
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart-helper
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)250
G Commandsgraceful-restart-helper
graceful-restartgraceful-restart helper-disable
Description: Disable OSPF Policy Graceful Restart Helper
Syntax:
disable Restart helperhelper-disable
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# graceful-restart helper-disable
graceful-restart stalepath-time <NUMBER>
Description: Set BGP Policy Graceful Restart Timers
Syntax:
Maximum time that BGP keeps stale routes from the restarting BGPpeer
stalepath-time
Timer Value in Seconds. Number range from=1 to=3600<1-3600>
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# graceful-restart stalepath-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 251
G Commandsgraceful-restart
groupgroup <WORD>
Description: Specify server groups
Syntax:
Server group name (Max Size 127)<WORD>
Command Mode: aaa authentication login console : Configure console methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login console(config-console)# group <WORD>
group <WORD>
Description: Specify server groups
Syntax:
Server group name (Max Size 127)<WORD>
Command Mode: aaa authentication login default : Configure default methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login default(config-default)# group <WORD>
group <WORD>
Description: Set provider group for login domain
Syntax:
Server group name (Max Size 127)<WORD>
Command Mode: aaa authentication login domain : Configure domain methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>(config-domain)# group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)252
G Commandsgroup
H Commands
• hello-interval, page 254
• http, page 255
• https, page 256
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 253
hello-intervalhello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)254
H Commandshello-interval
httphttp
Description: HTTP communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 255
H Commandshttp
httpshttps
Description: HTTPS communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)256
H Commandshttps
I Commands
• inband-mgmt, page 261
• inband-mgmt epg, page 262
• inherit, page 263
• inherit bgp address-family, page 266
• inherit bgp dampening, page 267
• inherit eigrp, page 268
• inherit ipv4, page 269
• inherit ipv6, page 270
• instance, page 272
• interface, page 273
• interface ethernet, page 275
• interface inband-mgmt0, page 276
• interface mgmt0, page 277
• interface port-channel, page 278
• interface vlan, page 279
• interface vpc, page 280
• ip, page 281
• ip address-range, page 282
• ip address, page 284
• ip address tenant application, page 287
• ip address tenant external-l2, page 289
• ip address tenant external-l3, page 291
• ip bandwidth, page 293
• ip bfd, page 295
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 257
• ip dhcp relay address tenant application, page 297
• ip dhcp relay address tenant external-l2, page 298
• ip dhcp relay address tenant external-l3, page 299
• ip distribute-list eigrp, page 300
• ip dscp, page 301
• ip hello-interval, page 303
• ip hold-interval, page 305
• ip igmp snooping fast-leave, page 307
• ip igmp snooping last-member-query-interval, page 308
• ip igmp snooping optimise-multicast-flood, page 309
• ip igmp snooping policy, page 310
• ip igmp snooping querier, page 311
• ip igmp snooping query-interval, page 312
• ip igmp snooping query-max-response-time, page 313
• ip igmp snooping startup-query-count, page 314
• ip igmp snooping startup-query-interval, page 315
• ip next-hop-self, page 316
• ip ospf authentication-key, page 318
• ip ospf authentication, page 319
• ip ospf bfd, page 320
• ip ospf cost, page 321
• ip ospf dead-interval, page 322
• ip ospf hello-interval, page 323
• ip ospf inherit, page 324
• ip ospf mtu-ignore, page 325
• ip ospf network, page 326
• ip ospf passive-interface, page 327
• ip ospf prefix-suppression, page 328
• ip ospf priority, page 329
• ip ospf retransmit-interval, page 330
• ip ospf transmit-delay, page 331
• ip passive-interface, page 332
• ip prefix-list, page 334
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)258
I Commands
• ip prefix-list permit le, page 335
• ip router eigrp, page 336
• ip router ospf default, page 337
• ip shared address consumer, page 338
• ip shared address provider, page 339
• ip split-horizon, page 340
• ip summary-address eigrp, page 342
• ip throughput-delay, page 343
• ip ttl, page 345
• iprange, page 347
• ipv6, page 348
• ipv6 address-range, page 349
• ipv6 address, page 351
• ipv6 address tenant application, page 354
• ipv6 address tenant external-l2, page 356
• ipv6 address tenant external-l3, page 358
• ipv6 bandwidth, page 360
• ipv6 bfd, page 361
• ipv6 dhcp relay address tenant application, page 362
• ipv6 dhcp relay address tenant external-l2, page 363
• ipv6 dhcp relay address tenant external-l3, page 364
• ipv6 distribute-list eigrp, page 365
• ipv6 hello-interval, page 366
• ipv6 hold-interval, page 367
• ipv6 link-local, page 368
• ipv6 nd hop-limit, page 370
• ipv6 nd managed-config-flag, page 372
• ipv6 nd mtu, page 374
• ipv6 nd ns-interval, page 376
• ipv6 nd ns-retries, page 378
• ipv6 nd other-config-flag, page 380
• ipv6 nd policy, page 382
• ipv6 nd prefix, page 383
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 259
I Commands
• ipv6 nd ra-interval, page 385
• ipv6 nd ra-lifetime, page 387
• ipv6 nd reachable-time, page 389
• ipv6 nd retrans-timer, page 391
• ipv6 nd suppress-ra-mtu, page 393
• ipv6 nd suppress-ra, page 395
• ipv6 next-hop-self, page 397
• ipv6 ospf bfd, page 398
• ipv6 ospf cost, page 399
• ipv6 ospf dead-interval, page 400
• ipv6 ospf hello-interval, page 401
• ipv6 ospf inherit, page 402
• ipv6 ospf mtu-ignore, page 403
• ipv6 ospf network, page 404
• ipv6 ospf passive-interface, page 405
• ipv6 ospf prefix-suppression, page 406
• ipv6 ospf priority, page 407
• ipv6 ospf retransmit-interval, page 408
• ipv6 ospf transmit-delay, page 409
• ipv6 passive-interface, page 410
• ipv6 router eigrp, page 411
• ipv6 router ospf default, page 412
• ipv6 shared address consumer, page 413
• ipv6 shared address provider, page 414
• ipv6 split-horizon, page 415
• ipv6 throughput-delay, page 416
• isis, page 418
• isolation, page 419
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)260
I Commands
inband-mgmtinband-mgmt epg <WORD>
Description: Enter Inside In-band management mode to modify inband properties or create new inband
Syntax:
inband mgmt epg label, usage inband-mgmt epgepg
epg name for inband epg, it can be existing inband epg or new oneWORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 261
I Commandsinband-mgmt
inband-mgmt epginband-mgmt epg <WORD>
Description: Associate node to a Inband EPG
Syntax:
Inband End Point Group Name (Max Size 64)WORD
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# inband-mgmt epg <WORD>
inband-mgmt epg <WORD>
Description: Associate node to a Inband EPG
Syntax:
Inband End Point Group Name (Max Size 64)WORD
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# inband-mgmt epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)262
I Commandsinband-mgmt epg
inheritinherit bfd ip|ipv6 <WORD>
Description: Inherit BFD Policy
Syntax:
bfd
IPv4 Addressip
IPv6 Addressipv6
Inherit a BFD PolicyWORD
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# inherit bfd ip|ipv6 <WORD>
inherit route-profile <WORD>
Description: Inherit a policy template
Syntax:
Configure route-profile for bridge-domainroute-profile
Route profile nameWORD
Command Mode: match bridge-domain : Match subnets of a bridge-domain
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <>(config-leaf-vrf-route-map-match)# inherit route-profile <WORD>
inherit route tag <WORD>
Description: Inherit a policy template
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 263
I Commandsinherit
Policy template for routesroute
Route tag policy templatetag
Policy template name (Max Size 64)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# inherit route tag <WORD>
inherit eigrp vrf-policy <WORD>
Description: Inherit EIGRP VRF Policy under this VRF
Syntax:
Inherit EIGRP VRF Policyeigrp
Inherit EIGRP VRF Policyvrf-policy
Policy nameWORD
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# inherit eigrp vrf-policy <WORD>
inherit bgp timer <WORD>
Description: Inherit BGP Timer Template Policy under this VRF
Syntax:
Inherit BGP Timer Policybgp
Inherit BGP Timer Policytimer
BGP Template Policy Name (Max Size 64)WORD
Command Mode: vrf : Virtual Router Context
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)264
I Commandsinherit
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# inherit bgp timer <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 265
I Commandsinherit
inherit bgp address-familyinherit bgp address-family <WORD>
Description: Inherit BGP Address Family Policy
Syntax:
BGP Address Family Policy Name (Max Size 64)WORD
Command Mode: address-family : Configure an address-family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp address-family <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)266
I Commandsinherit bgp address-family
inherit bgp dampeninginherit bgp dampening <WORD>
Description: Inherit Route Profile with BGP Dampening Policy
Syntax:
Route Profile with BGP Dampening Policy Name (Max Size 64)WORD
Command Mode: address-family : Configure an address-family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-af)# inherit bgp dampening <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 267
I Commandsinherit bgp dampening
inherit eigrpinherit eigrp ip|ipv6 interface-policy <WORD>
Description: Inherit EIGRP interface template policy
Syntax:
Address Family IPv4ip
Address Family IPv6ipv6
Associate the interface with an EIGRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>
inherit eigrp ip|ipv6 interface-policy <WORD>
Description: Inherit EIGRP interface template policy
Syntax:
Address Family IPv4ip
Address Family IPv6ipv6
Associate the interface with an EIGRP interface policyinterface-policy
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit eigrp ip|ipv6 interface-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)268
I Commandsinherit eigrp
inherit ipv4inherit ipv4 ospf vrf-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF Policyospf
Inherit OSPF vrf-policyvrf-policy
OSPF Template Policy name (Max Size 64)WORD
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv4 ospf vrf-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 269
I Commandsinherit ipv4
inherit ipv6inherit ipv6 nd <WORD>
Description: Inherit IPv6 Neighbor Discovery template policy
Syntax:
Associate the interface with an IPv6 Neighbor Discovery policynd
Policy nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# inherit ipv6 nd <WORD>
inherit ipv6 nd <WORD>
Description: Inherit IPv6 Neighbor Discovery template policy
Syntax:
Associate the interface with an IPv6 Neighbor Discovery policynd
Policy nameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# inherit ipv6 nd <WORD>
inherit ipv6 ospf vrf-policy <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF Policyospf
Inherit OSPF vrf-policyvrf-policy
OSPF Template Policy name (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)270
I Commandsinherit ipv6
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# inherit ipv6 ospf vrf-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 271
I Commandsinherit ipv6
instanceinstance <NUMBER> vlan <RANGE>
Description:Maps VLANs to an MST instance
Syntax:
MST instance ID. Number range from=1 to=4094<1-4094>
Virtual LANvlan
VLAN range. Ex.: 10-3000RANGE
Command Mode: region : STP MST region configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# instance <NUMBER> vlan <RANGE>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)272
I Commandsinstance
interfaceinterface bridge-domain <WORD>
Description: Configuration for interface bridge-domain
Syntax:
Name of the bridge-domainbridge-domain
Name of the bridge-domain (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>
interface ethernet
Description: Provide a Range of Interfaces
Syntax:
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# interface ethernet
interface ethernet
Description: Configure Ports on the Fex Interface Group
Syntax:
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 273
I Commandsinterface
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# interface ethernet
interface vpc <WORD> [fex <fex>]
Description: Provide VPC Name
Syntax:
VPC Interfacevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: vpc context : Enter vpc context
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)274
I Commandsinterface
interface ethernetinterface ethernet <ethernet> leaf <leaf-id>
Description: Configure Physical Ethernet Port as a Cluster Member Interface
Syntax:
List of ethernet itfs<ethernet>
Leaf ID that connects to cluster ethernet interface on (physical) device.leaf
Leaf ID that connects to cluster ethernet interface on (physical) device.<leaf-id>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface ethernet <ethernet> leaf <leaf-id>
interface ethernet <ifRange>
Description: Ethernet IEEE 802.3z
Syntax:
interface Range<ifRange>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 275
I Commandsinterface ethernet
interface inband-mgmt0interface inband-mgmt0
Description: Inband management interface
Command Mode: controller : Configure Controller Node
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0
interface inband-mgmt0
Description: Inband management interface
Command Mode: switch : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)276
I Commandsinterface inband-mgmt0
interface mgmt0interface mgmt0
Description: Out of band management interface
Command Mode: controller : Configure Controller Node
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0
interface mgmt0
Description: Out of band management interface
Command Mode: switch : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 277
I Commandsinterface mgmt0
interface port-channelinterface port-channel <port-channel-name> leaf <NUMBER> [fex <fex-id>]
Description: Configure Port Channel as a Cluster Member Interface
Syntax:
Name of the port-channel<port-channel-name>
Leaf Id for the port-channelleaf
Leaf Id for the port channel.. Number range from=0to=9223372036854775807
NUMBER
(Optional) Fex ID that connects to cluster interface interface on(physical) device.
<fex-id>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface port-channel <port-channel-name> leaf <NUMBER> [fex <fex-id>]
interface port-channel <WORD> [fex <fex>]
Description: Port Channel interface
Syntax:
Port-Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)278
I Commandsinterface port-channel
interface vlaninterface vlan <1-4094>
Description: Vlan interface
Syntax:
Vlan interface number<1-4094>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 279
I Commandsinterface vlan
interface vpcinterface vpc <vpc-name> leaf <NUMBER> <NUMBER> [fex fex <Ids>]
Description: Configure monitor for VPC interfaces
Syntax:
VPC port-channel group name<vpc-name>
leafleaf
First leaf member of the Pair. Number range from=0to=9223372036854775807
NUMBER
Second leaf member of the Pair. Number range from=0to=9223372036854775807
NUMBER
(Optional) paired fex Idsfex <Ids>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# interface vpc <vpc-name> leaf <NUMBER> <NUMBER> [fex fex <Ids>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)280
I Commandsinterface vpc
ipip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Description: Configure IP features
Syntax:
Route informationroute
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
ipAddress|null
<ZeroorPref>
<BfdorPref>
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ip route <A.B.C.D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 281
I Commandsip
ip address-rangeip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP Address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP Address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)282
I Commandsip address-range
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ip address-range <A.B.C.D/LEN> gateway <A.B.C.D>
ip address-range <A.B.C.D> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ip address-range <A.B.C.D> gateway <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 283
I Commandsip address-range
ip addressip address <A.B.C.D/LEN> [scope <scope>] [secondary] [multi-site] [snooping-querier]
Description: Define an IPv4 subnet to be exported by the BD
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Scope of the address among ['public', 'private']scope
(Optional) Set the address as secondary addresssecondary
(Optional) Set the address as multi-site addressmulti-site
(Optional) Tell the address to be used by IGMP Snooping querierfunctionality if enabled
snooping-querier
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip address <A.B.C.D/LEN> [scope <scope>] [secondary] [multi-site][snooping-querier]
ip address <A.B.C.D/LEN> [secondary]
Description: Configure IP address on interface
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Configure additional IP addresses on interfacesecondary
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]
ip address <A.B.C.D/LEN> [secondary]
Description: Configure IP address on interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)284
I Commandsip address
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
(Optional) Configure IP Address as Secondary IPsecondary
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip address <A.B.C.D/LEN> [secondary]
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 285
I Commandsip address
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Description: Configure IP and gateway features
Syntax:
IP address and network mask length in format x.x.x.x/mA.B.C.D/LEN
Configure gateway address on interfacegateway
Network mask length in format x.x.x.xA.B.C.D
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ip address <A.B.C.D/LEN> gateway <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)286
I Commandsip address
ip address tenant applicationip address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> application <WORD> epg<WORD>
ip address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 287
I Commandsip address tenant application
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> application <WORD>epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)288
I Commandsip address tenant application
ip address tenant external-l2ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
ip address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l2 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 289
I Commandsip address tenant external-l2
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)290
I Commandsip address tenant external-l2
ip address tenant external-l3ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
ip address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ip address <A.B.C.D> tenant <WORD> external-l3 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 291
I Commandsip address tenant external-l3
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)292
I Commandsip address tenant external-l3
ip bandwidthip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>
ip bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 293
I Commandsip bandwidth
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip bandwidth eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)294
I Commandsip bandwidth
ip bfdip bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip bfd enable
ip bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip bfd eigrp enable
ip bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 295
I Commandsip bfd
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip bfd eigrp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)296
I Commandsip bfd
ip dhcp relay address tenant applicationip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> application <WORD>epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 297
I Commandsip dhcp relay address tenant application
ip dhcp relay address tenant external-l2ip dhcp relay address <A.B.C.D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> external-l2 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)298
I Commandsip dhcp relay address tenant external-l2
ip dhcp relay address tenant external-l3ip dhcp relay address <A.B.C.D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IP address in format i.i.i.iA.B.C.D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip dhcp relay address <A.B.C.D> tenant <WORD> external-l3 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 299
I Commandsip dhcp relay address tenant external-l3
ip distribute-list eigrpip distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP route-map
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out
ip distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP Policies
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip distribute-list eigrp default route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)300
I Commandsip distribute-list eigrp
ip dscpip dscp <dscp>
Description: dscp
Syntax:
DSCP code or valuedscp
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# ip dscp <dscp>
ip dscp <dscp>
Description: dscp
Syntax:
DSCP code or valuedscp
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# ip dscp <dscp>
ip dscp <dscp>
Description: dscp
Syntax:
DSCP code or valuedscp
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 301
I Commandsip dscp
(config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# ip dscp <dscp>
ip dscp <dscp>
Description: Configure DSCP
Syntax:
<dscp><dscp>
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# ip dscp <dscp>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)302
I Commandsip dscp
ip hello-intervalip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>
ip hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 303
I Commandsip hello-interval
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip hello-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)304
I Commandsip hello-interval
ip hold-intervalip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>
ip hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 305
I Commandsip hold-interval
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip hold-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)306
I Commandsip hold-interval
ip igmp snooping fast-leaveip igmp snooping fast-leave
Description: Enable IP IGMP Snooping fast leave processing
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping fast-leave
ip igmp snooping fast-leave
Description: Enable IP IGMP Snooping fast leave processing
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping fast-leave
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 307
I Commandsip igmp snooping fast-leave
ip igmp snooping last-member-query-intervalip igmp snooping last-member-query-interval <NUMBER>
Description: Change the IP IGMP snooping last member query interval param
Syntax:
Last Memeber Query Interval Value. Number range from=1 to=25<1-25>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping last-member-query-interval <NUMBER>
ip igmp snooping last-member-query-interval <NUMBER>
Description: Change the IP IGMP snooping last member query interval param
Syntax:
Last Memeber Query Interval Value. Number range from=1 to=25<1-25>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping last-member-query-interval<NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)308
I Commandsip igmp snooping last-member-query-interval
ip igmp snooping optimise-multicast-floodip igmp snooping optimise-multicast-flood
Description: Enable IP IGMP Snooping multicast flood optimization
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping optimise-multicast-flood
ip igmp snooping optimise-multicast-flood
Description: Enable IP IGMP Snooping multicast flood optimization
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping optimise-multicast-flood
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 309
I Commandsip igmp snooping optimise-multicast-flood
ip igmp snooping policyip igmp snooping policy <WORD>
Description: Associate the BD with an IGMP snooping policy
Syntax:
Name of the IGMP snooping policy to attach (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)310
I Commandsip igmp snooping policy
ip igmp snooping querierip igmp snooping querier
Description: Enable IP IGMP Snooping querier processing
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping querier
ip igmp snooping querier
Description: Enable IP IGMP Snooping querier processing
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping querier
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 311
I Commandsip igmp snooping querier
ip igmp snooping query-intervalip igmp snooping query-interval <NUMBER>
Description: Change the IP IGMP snooping query interval param
Syntax:
Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping query-interval <NUMBER>
ip igmp snooping query-interval <NUMBER>
Description: Change the IP IGMP snooping query interval param
Syntax:
Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping query-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)312
I Commandsip igmp snooping query-interval
ip igmp snooping query-max-response-timeip igmp snooping query-max-response-time <NUMBER>
Description: Change the IP IGMP snooping max query response time
Syntax:
Query Max Response Time. Number range from=1 to=25<1-25>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping query-max-response-time <NUMBER>
ip igmp snooping query-max-response-time <NUMBER>
Description: Change the IP IGMP snooping max query response time
Syntax:
Query Max Response Time. Number range from=1 to=25<1-25>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping query-max-response-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 313
I Commandsip igmp snooping query-max-response-time
ip igmp snooping startup-query-countip igmp snooping startup-query-count <NUMBER>
Description: Change the IP IGMP snooping number of initial queries to send
Syntax:
Start Query Count. Number range from=1 to=10<1-10>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping startup-query-count <NUMBER>
ip igmp snooping startup-query-count <NUMBER>
Description: Change the IP IGMP snooping number of initial queries to send
Syntax:
Start Query Count. Number range from=1 to=10<1-10>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping startup-query-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)314
I Commandsip igmp snooping startup-query-count
ip igmp snooping startup-query-intervalip igmp snooping startup-query-interval <NUMBER>
Description: Change the IP IGMP snooping time for sending initial queries
Syntax:
Start Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip igmp snooping startup-query-interval <NUMBER>
ip igmp snooping startup-query-interval <NUMBER>
Description: Change the IP IGMP snooping time for sending initial queries
Syntax:
Start Query Interval Value. Number range from=1 to=18000<1-18000>
Command Mode: template ip igmp snooping policy : Create an IGMP snooping policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>(config-tenant-template-ip-igmp-snooping)# ip igmp snooping startup-query-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 315
I Commandsip igmp snooping startup-query-interval
ip next-hop-selfip next-hop-self eigrp default
Description: Set the next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip next-hop-self eigrp default
ip next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)316
I Commandsip next-hop-self
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip next-hop-self eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 317
I Commandsip next-hop-self
ip ospf authentication-keyip ospf authentication-key <WORD>
Description: Set OSPF authentication key
Syntax:
OSPF authentication keyWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication-key <WORD>
ip ospf authentication-key <WORD>
Description: Set OSPF authentication key
Syntax:
OSPF authentication keyWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication-key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)318
I Commandsip ospf authentication-key
ip ospf authenticationip ospf authentication md5|none|simple
Description: Set the OSPF authentication type
Syntax:
MD5 authenticationmd5
No authenticationnone
Simple authenticationsimple
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf authentication md5|none|simple
ip ospf authentication md5|none|simple
Description: Set the OSPF authentication type
Syntax:
MD5 authenticationmd5
No authenticationnone
Simple authenticationsimple
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf authentication md5|none|simple
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 319
I Commandsip ospf authentication
ip ospf bfdip ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf bfd enable
ip ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf bfd enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)320
I Commandsip ospf bfd
ip ospf costip ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf cost <NUMBER>
ip ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf cost <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 321
I Commandsip ospf cost
ip ospf dead-intervalip ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf dead-interval <NUMBER>
ip ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)322
I Commandsip ospf dead-interval
ip ospf hello-intervalip ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf hello-interval <NUMBER>
ip ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 323
I Commandsip ospf hello-interval
ip ospf inheritip ospf inherit interface-policy <WORD> tenant <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
tenant nametenant
Tenant name (Max Size 63)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf inherit interface-policy <WORD> tenant <WORD>
ip ospf inherit interface-policy <WORD> tenant <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
tenant nametenant
Tenant name (Max Size 63)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf inherit interface-policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)324
I Commandsip ospf inherit
ip ospf mtu-ignoreip ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf mtu-ignore
ip ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf mtu-ignore
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 325
I Commandsip ospf mtu-ignore
ip ospf networkip ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf network bcast|p2p|unspecified
ip ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)326
I Commandsip ospf network
ip ospf passive-interfaceip ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf passive-interface
ip ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf passive-interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 327
I Commandsip ospf passive-interface
ip ospf prefix-suppressionip ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit
ip ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf prefix-suppression disable|enable|inherit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)328
I Commandsip ospf prefix-suppression
ip ospf priorityip ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf priority <NUMBER>
ip ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 329
I Commandsip ospf priority
ip ospf retransmit-intervalip ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>
ip ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf retransmit-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)330
I Commandsip ospf retransmit-interval
ip ospf transmit-delayip ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip ospf transmit-delay <NUMBER>
ip ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip ospf transmit-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 331
I Commandsip ospf transmit-delay
ip passive-interfaceip passive-interface eigrp default
Description: Set the passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip passive-interface eigrp default
ip passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)332
I Commandsip passive-interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip passive-interface eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 333
I Commandsip passive-interface
ip prefix-listip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>
Description: Build a prefix-list
Syntax:
Name of prefix-list (Max Size 64)WORD
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)334
I Commandsip prefix-list
ip prefix-list permit leip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le <32>
Description:Maximum prefix length to be matched
Syntax:
Name of prefix-list (Max Size 64)WORD
Specify routes to forwardpermit
IP prefix network/length, e.g., 35.0.0.0/8 or 2001::/64A.B.C.D/LEN | A:B::C:D/LEN
Maximum prefix length32
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# ip prefix-list <WORD> permit <A.B.C.D/LEN | A:B::C:D/LEN> le<32>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 335
I Commandsip prefix-list permit le
ip router eigrpip router eigrp default
Description: Configure Router EIGRP Policies
Syntax:
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip router eigrp default
ip router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)336
I Commandsip router eigrp
ip router ospf defaultip router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>
ip router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip router ospf default area <A.B.C.D|NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 337
I Commandsip router ospf default
ip shared address consumerip shared address <A.B.C.D/LEN> consumer application any epg any
Description: Shared consumed service
Syntax:
IPv4 subnetaddress
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
application keywordapplication
any applicationany
epg keywordepg
any EPGany
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip shared address <A.B.C.D/LEN> consumer application any epg any
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)338
I Commandsip shared address consumer
ip shared address providerip shared address <A.B.C.D/LEN> provider application <WORD> epg <WORD> [scope <scope>]
Description: Shared provider service
Syntax:
IPv4 subnetaddress
IP prefix and network mask length in format x.x.x.x/mA.B.C.D/LEN
application keywordapplication
Application Name (Max Size 64)WORD
epg keywordepg
Application EPG (Max Size 64)WORD
(Optional) Scope of the address among ['public']scope
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ip shared address <A.B.C.D/LEN> provider application <WORD> epg<WORD> [scope <scope>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 339
I Commandsip shared address provider
ip split-horizonip split-horizon eigrp default
Description: Set the split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip split-horizon eigrp default
ip split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)340
I Commandsip split-horizon
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip split-horizon eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 341
I Commandsip split-horizon
ip summary-address eigrpip summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV4/IPV6 address (e.g. 10.0.0.0/8 or 2001:0DB8:0:1::/64)IP-PREFIX/LEN
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>
ip summary-address eigrp default <IP-PREFIX/LEN>
Description: Configure route summarization for EIGRP
Syntax:
EIGRP default instancedefault
Summary IPV4/IPV6 address (e.g. 10.0.0.0/8 or 2001:0DB8:0:1::/64)IP-PREFIX/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip summary-address eigrp default <IP-PREFIX/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)342
I Commandsip summary-address eigrp
ip throughput-delayip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughut delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughtput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: template eigrp interface-policy : Configure EIGRP Interface policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>(config-template-eigrp-if-pol)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughut delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughtput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 343
I Commandsip throughput-delay
(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughut delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughtput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ip throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)344
I Commandsip throughput-delay
ip ttlip ttl <ttl>
Description: TTL
Syntax:
ttl value. Number range from=1 to=255ttl
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# ip ttl <ttl>
ip ttl <ttl>
Description: TTL
Syntax:
ttl value. Number range from=1 to=255ttl
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# ip ttl <ttl>
ip ttl <arg>
Description: TTL
Syntax:
ttl value. Number range from=1 to=255arg
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 345
I Commandsip ttl
(config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-tenant-dest)# ip ttl <>
ip ttl <arg>
Description: Configure TTL
Syntax:
TTL value. Number range from=1 to=255arg
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# ip ttl <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)346
I Commandsip ttl
iprangeiprange <startip> <endip>
Description: Add ip pool
Syntax:
startipstartip
endipendip
Command Mode: microsoft : Configure static ip pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# iprange <startip> <endip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 347
I Commandsiprange
ipv6ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Description: Configure IPv6 features
Syntax:
Configure IPv6 unicast static routeroute
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
ipAddress|null
<ZeroorPref>
<BfdorPref>
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# ipv6 route <A:B::C:D/LEN> <ipAddress|null> <ZeroorPref> <BfdorPref>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)348
I Commandsipv6
ipv6 address-rangeipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 349
I Commandsipv6 address-range
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Description: Configure IPv6 Address Range
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C:X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ipv6 address-range <A:B:C::X/LEN> gateway <A:B:C:X>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)350
I Commandsipv6 address-range
ipv6 addressipv6 address <A:B::C:D/LEN> [scope <scope>] [preferred] [suppress-nd] [eui64]
Description: Define an IPv6 subnet to be exported by the BD
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
(Optional) Scope of the address among ['public', 'private']scope
(Optional) Set the address as preferred addresspreferred
(Optional) Suppress the Neighbor Discovery on this subnetsuppress-nd
(Optional) Use eui64 interface identifiereui64
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 address <A:B::C:D/LEN> [scope <scope>] [preferred][suppress-nd] [eui64]
ipv6 address <A:B::C:D/LEN> eui64 preferred
Description: Configure IPv6 address on interface
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Configure Extended Unique Identifier for the low-order 64 bitseui64
Configure IPv6 address as preferredpreferred
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 preferred
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 351
I Commandsipv6 address
ipv6 address <A:B::C:D/LEN> eui64 preferred
Description: Configure IPv6 address on interface
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Configure Extended Unique Identifier for the low-order 64 bitseui64
Configure IPv6 address as preferredpreferred
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 address <A:B::C:D/LEN> eui64 preferred
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IP and gateway features
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IPv6 Address and Gateway
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)352
I Commandsipv6 address
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IP and gateway features
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Description: Configure IPv6 Address and Gateway
Syntax:
IPv6 address and network mask lengthA:B:C::X/LEN
Configure gateway address on interfacegateway
Gateway IPv6 addressA:B:C::X
Command Mode: interface inband-mgmt0 : Inband management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface inband-mgmt0(config-switch-if)# ipv6 address <A:B:C::X/LEN> gateway <A:B:C::X>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 353
I Commandsipv6 address
ipv6 address tenant applicationipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg<WORD>
ipv6 address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)354
I Commandsipv6 address tenant application
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> application<WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 355
I Commandsipv6 address tenant application
ipv6 address tenant external-l2ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l2 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)356
I Commandsipv6 address tenant external-l2
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 357
I Commandsipv6 address tenant external-l2
ipv6 address tenant external-l3ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>(config-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: template dhcp relay : Create a DHCP Relay policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>(config-tenant-template-dhcp-relay)# ipv6 address <A:B::C:D> tenant <WORD> external-l3 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)358
I Commandsipv6 address tenant external-l3
<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 359
I Commandsipv6 address tenant external-l3
ipv6 bandwidthipv6 bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>
ipv6 bandwidth eigrp default <NUMBER>
Description: Set EIGRP bandwidth
Syntax:
EIGRPeigrp
EIGRP default instancedefault
bandwidth in kbps. Number range from=0 to=2560000000<0-2560000000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bandwidth eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)360
I Commandsipv6 bandwidth
ipv6 bfdipv6 bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 bfd eigrp enable
ipv6 bfd eigrp enable
Description: Enable EIGRP Bidirectional Forwarding Detection
Syntax:
EIGRPeigrp
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 bfd eigrp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 361
I Commandsipv6 bfd
ipv6 dhcp relay address tenant applicationipv6 dhcp relay address <A:B::C:D> tenant <WORD> application <WORD> epg <WORD>
Description: Add a new server relay address under an AEPg
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
Application hosting the EPG (Max Size 64)WORD
AEPg behind which the DHCP server sitsepg
AEPg behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> application<WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)362
I Commandsipv6 dhcp relay address tenant application
ipv6 dhcp relay address tenant external-l2ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l2 epg <WORD>
Description: Add a new server relay address under a L2 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
epg keywordepg
l2 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l2 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 363
I Commandsipv6 dhcp relay address tenant external-l2
ipv6 dhcp relay address tenant external-l3ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l3 epg <WORD>
Description: Add a new server relay address under a L3 External EPG
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Tenant hosting the DHCP servertenant
Tenant hosting the EPG (Max Size 63)WORD
EPG keywordepg
l3 external EPG behind which the DHCP server sits (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 dhcp relay address <A:B::C:D> tenant <WORD> external-l3 epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)364
I Commandsipv6 dhcp relay address tenant external-l3
ipv6 distribute-list eigrpipv6 distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP route-map
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out
ipv6 distribute-list eigrp default route-map <WORD> out
Description: Configure distribute-list EIGRP Policies
Syntax:
EIGRP default instancedefault
route maproute-map
Route-map name (Max Size 64)WORD
outout
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 distribute-list eigrp default route-map <WORD> out
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 365
I Commandsipv6 distribute-list eigrp
ipv6 hello-intervalipv6 hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>
ipv6 hello-interval eigrp default <NUMBER>
Description: Set EIGRP Hello interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hello interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hello-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)366
I Commandsipv6 hello-interval
ipv6 hold-intervalipv6 hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>
ipv6 hold-interval eigrp default <NUMBER>
Description: Set EIGRP Hold interval time
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Hold interval time in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 hold-interval eigrp default <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 367
I Commandsipv6 hold-interval
ipv6 link-localipv6 link-local <A:B::C:D>
Description: Configure IPv6 link-local address
Syntax:
IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 link-local <A:B::C:D>
ipv6 link-local <X:X:X:X::X>
Description: Configure IPv6 link-local address
Syntax:
IPv6 link-local addressX:X:X:X::X
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 link-local <X:X:X:X::X>
ipv6 link-local <X:X:X:X::X>
Description: Configure IPv6 link-local address
Syntax:
IPv6 link-local addressX:X:X:X::X
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)368
I Commandsipv6 link-local
(config-leaf-if)# ipv6 link-local <X:X:X:X::X>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 369
I Commandsipv6 link-local
ipv6 nd hop-limitipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)370
I Commandsipv6 nd hop-limit
(config-template-nd-pol)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>
ipv6 nd hop-limit <NUMBER>
Description: Set the hop limit to be advertised in IPv6 neighbor discovery packets
Syntax:
Hop Limit. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd hop-limit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 371
I Commandsipv6 nd hop-limit
ipv6 nd managed-config-flagipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd managed-config-flag
ipv6 nd managed-config-flag
Description: Use stateful address auto-configuration to obtain address information
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)372
I Commandsipv6 nd managed-config-flag
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd managed-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 373
I Commandsipv6 nd managed-config-flag
ipv6 nd mtuipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)374
I Commandsipv6 nd mtu
(config-template-nd-pol)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd mtu <NUMBER>
ipv6 nd mtu <NUMBER>
Description: Set the mtu to be advertised in IPv6 neighbor discovery packets
Syntax:
MTU value. Number range from=1280 to=9000<1280-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd mtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 375
I Commandsipv6 nd mtu
ipv6 nd ns-intervalipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)376
I Commandsipv6 nd ns-interval
(config-template-nd-pol)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>
ipv6 nd ns-interval <NUMBER>
Description: Set the retransmission interval between IPv6 neighbor solicitation messages
Syntax:
Interval value. Number range from=1000 to=3600000<1000-3600000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 377
I Commandsipv6 nd ns-interval
ipv6 nd ns-retriesipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)378
I Commandsipv6 nd ns-retries
(config-template-nd-pol)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>
ipv6 nd ns-retries <NUMBER>
Description: Set the retry count for for sending neighbor solicitation messages
Syntax:
Number of retries. Number range from=1 to=100<1-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ns-retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 379
I Commandsipv6 nd ns-retries
ipv6 nd other-config-flagipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd other-config-flag
ipv6 nd other-config-flag
Description: Use stateful auto-configuration to obtain NON-address information
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)380
I Commandsipv6 nd other-config-flag
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd other-config-flag
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 381
I Commandsipv6 nd other-config-flag
ipv6 nd policyipv6 nd policy <WORD>
Description: Associate the BD with an IPv6 Neighbor Discovery policy
Syntax:
Name of the policy to associate (Max Size 64)WORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)382
I Commandsipv6 nd policy
ipv6 nd prefixipv6 nd prefix <A:B::C:D/LEN> <NUMBER> <NUMBER> [no-autoconfig] [no-onlink] [router-address]
Description: Advertise in Neighbor Discover a Prefix and configure the parameters
Syntax:
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
Lifetime to advertise for the prefix, in seconds. Number range from=0to=4294967295
<0-4294967295>
Preferred lifetime to advertise, in seconds. Number range from=0to=4294967295
<0-4294967295>
(Optional) advertise with A bit clearno-autoconfig
(Optional) advertise with L bit clearno-onlink
(Optional) Set this prefix as usable as default gateway by the hostsrouter-address
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd prefix <A:B::C:D/LEN> <NUMBER> <NUMBER> [no-autoconfig][no-onlink] [router-address]
ipv6 nd prefix <NUMBER> <NUMBER> [no-autoconfig] [no-onlink] [router-address]
Description: Advertise in Neighbor Discover a Prefix and configure the parameters
Syntax:
Lifetime to advertise for the prefix, in seconds. Number range from=0to=4294967295
<0-4294967295>
Preferred lifetime to advertise, in seconds. Number range from=0to=4294967295
<0-4294967295>
(Optional) advertise with A bit clearno-autoconfig
(Optional) advertise with L bit clearno-onlink
(Optional) Set this prefix as usable as default gateway by the hostsrouter-address
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 383
I Commandsipv6 nd prefix
Command Mode: template ipv6 nd prefix : Create/modify an an IPv6 Neighbor Prefix policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd prefix policy <WORD>(config-tenant-template-ipv6-nd-pfx)# ipv6 nd prefix <NUMBER> <NUMBER> [no-autoconfig][no-onlink] [router-address]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)384
I Commandsipv6 nd prefix
ipv6 nd ra-intervalipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 385
I Commandsipv6 nd ra-interval
(config-template-nd-pol)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>
ipv6 nd ra-interval <NUMBER>
Description: Set the interval between sending ICMPv6 router advertisement messages
Syntax:
Interval in seconds. Number range from=200 to=1800<200-1800>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)386
I Commandsipv6 nd ra-interval
ipv6 nd ra-lifetimeipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 387
I Commandsipv6 nd ra-lifetime
(config-template-nd-pol)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>
ipv6 nd ra-lifetime <NUMBER>
Description: Set the router lifetime of a default router in ICMPv6 router advertisement messages
Syntax:
Lifetime in seconds. Number range from=0 to=9000<0-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd ra-lifetime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)388
I Commandsipv6 nd ra-lifetime
ipv6 nd reachable-timeipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in seconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Reachable timer in seconds. Number range from=0 to=3600000<0-3600000>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Time in seconds. Number range from=0 to=3600000<0-3600000>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 389
I Commandsipv6 nd reachable-time
(config-template-nd-pol)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Time in seconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>
ipv6 nd reachable-time <NUMBER>
Description: Set the time for reachability confirmation in ICMPv6 router advertisement messages
Syntax:
Time in seconds. Number range from=0 to=3600000<0-3600000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd reachable-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)390
I Commandsipv6 nd reachable-time
ipv6 nd retrans-timeripv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer, in seconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Retransmit timer, in seconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Timer in seconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 391
I Commandsipv6 nd retrans-timer
(config-template-nd-pol)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Timer in seconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>
ipv6 nd retrans-timer <NUMBER>
Description: Set the time between neighbor solicitation (NS) messages in ICMPv6 router advertisement
Syntax:
Timer in seconds. Number range from=0 to=4294967295<0-4294967295>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd retrans-timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)392
I Commandsipv6 nd retrans-timer
ipv6 nd suppress-ra-mtuipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra-mtu
ipv6 nd suppress-ra-mtu
Description: Disable sending MTU option in ICMPv6 router advertisement messages
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 393
I Commandsipv6 nd suppress-ra-mtu
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra-mtu
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)394
I Commandsipv6 nd suppress-ra-mtu
ipv6 nd suppress-raipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Create/modify an an IPv6 Neighbor Discovery policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>(config-tenant-template-ipv6-nd)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: template ipv6 nd policy : Configure IPv6 Neighbor Discovery policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>(config-template-nd-pol)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 nd suppress-ra
ipv6 nd suppress-ra
Description: Disable sending ICMPv6 router advertisement messages
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 395
I Commandsipv6 nd suppress-ra
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 nd suppress-ra
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)396
I Commandsipv6 nd suppress-ra
ipv6 next-hop-selfipv6 next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 next-hop-self eigrp default
ipv6 next-hop-self eigrp default
Description: Set EIGRP next-hop-self flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 next-hop-self eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 397
I Commandsipv6 next-hop-self
ipv6 ospf bfdipv6 ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf bfd enable
ipv6 ospf bfd enable
Description: Enable Bidirectional Forwarding Detection
Syntax:
Enable BFDenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf bfd enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)398
I Commandsipv6 ospf bfd
ipv6 ospf costipv6 ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf cost <NUMBER>
ipv6 ospf cost <NUMBER>
Description: Set OSPF cost for the interface
Syntax:
OSPF cost. Number range from=0 to=65535<0-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf cost <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 399
I Commandsipv6 ospf cost
ipv6 ospf dead-intervalipv6 ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>
ipv6 ospf dead-interval <NUMBER>
Description: Set the interval between hello packets from a neighbor before the router declares the neighboras down
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)400
I Commandsipv6 ospf dead-interval
ipv6 ospf hello-intervalipv6 ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>
ipv6 ospf hello-interval <NUMBER>
Description: Set interval between hello packets that OSPF sends on the interface
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf hello-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 401
I Commandsipv6 ospf hello-interval
ipv6 ospf inheritipv6 ospf inherit interface-policy <WORD> tenant <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
tenant nametenant
Tenant name (Max Size 63)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD> tenant <WORD>
ipv6 ospf inherit interface-policy <WORD> tenant <WORD>
Description: Inherit OSPF Template Policy under this VRF
Syntax:
Inherit OSPF interface-policyinterface-policy
OSPF Template Policy name (Max Size 64)WORD
tenant nametenant
Tenant name (Max Size 63)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf inherit interface-policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)402
I Commandsipv6 ospf inherit
ipv6 ospf mtu-ignoreipv6 ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf mtu-ignore
ipv6 ospf mtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf mtu-ignore
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 403
I Commandsipv6 ospf mtu-ignore
ipv6 ospf networkipv6 ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified
ipv6 ospf network bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)404
I Commandsipv6 ospf network
ipv6 ospf passive-interfaceipv6 ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf passive-interface
ipv6 ospf passive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf passive-interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 405
I Commandsipv6 ospf passive-interface
ipv6 ospf prefix-suppressionipv6 ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit
ipv6 ospf prefix-suppression disable|enable|inherit
Description: Set prefix suppression
Syntax:
The OSPF interface prefix suppression.disable
The OSPF interface prefix suppression.enable
The OSPF interface prefix suppression.inherit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf prefix-suppression disable|enable|inherit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)406
I Commandsipv6 ospf prefix-suppression
ipv6 ospf priorityipv6 ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf priority <NUMBER>
ipv6 ospf priority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 407
I Commandsipv6 ospf priority
ipv6 ospf retransmit-intervalipv6 ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>
ipv6 ospf retransmit-interval <NUMBER>
Description: Set OSPF Policy Graceful Restart Timers
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf retransmit-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)408
I Commandsipv6 ospf retransmit-interval
ipv6 ospf transmit-delayipv6 ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>
ipv6 ospf transmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 ospf transmit-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 409
I Commandsipv6 ospf transmit-delay
ipv6 passive-interfaceipv6 passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 passive-interface eigrp default
ipv6 passive-interface eigrp default
Description: Set EIGRP passive-interface flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 passive-interface eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)410
I Commandsipv6 passive-interface
ipv6 router eigrpipv6 router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 router eigrp default
ipv6 router eigrp default
Description: Configure EIGRP default interface
Syntax:
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 411
I Commandsipv6 router eigrp
ipv6 router ospf defaultipv6 router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>
ipv6 router ospf default area <A.B.C.D|NUMBER>
Description: Process tag
Syntax:
Area associated with interfacearea
OSPF area IdA.B.C.D|NUMBER
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 router ospf default area <A.B.C.D|NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)412
I Commandsipv6 router ospf default
ipv6 shared address consumeripv6 shared address <A:B::C:D/LEN> consumer application any epg any
Description: Shared consumed service
Syntax:
IPv6 subnetaddress
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
application keywordapplication
any applicationany
epg keywordepg
any EPGany
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 shared address <A:B::C:D/LEN> consumer application any epgany
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 413
I Commandsipv6 shared address consumer
ipv6 shared address provideripv6 shared address <A:B::C:D/LEN> provider application <WORD> epg <WORD> [scope <scope>]
Description: Shared provider service
Syntax:
IPv6 subnetaddress
IPv6 prefix format: xxxx:xxxx/ml, xxxx:xxxx::/ml, xxxx::xx/128A:B::C:D/LEN
application keywordapplication
Application Name (Max Size 64)WORD
epg keywordepg
Application EPG (Max Size 64)WORD
(Optional) Scope of the address among ['public']scope
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# ipv6 shared address <A:B::C:D/LEN> provider application <WORD>epg <WORD> [scope <scope>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)414
I Commandsipv6 shared address provider
ipv6 split-horizonipv6 split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 split-horizon eigrp default
ipv6 split-horizon eigrp default
Description: Set EIGRP split-horizon flag
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# ipv6 split-horizon eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 415
I Commandsipv6 split-horizon
ipv6 throughput-delayipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughut delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughtput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Description: Set EIGRP throughut delay
Syntax:
EIGRPeigrp
EIGRP default instancedefault
Throughtput delay. Number range from=0 to=16777215<0-16777215>
Unit in 10-microsecondstens-of-micro
Unit in picosecondspico
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)416
I Commandsipv6 throughput-delay
(config-leaf-if)# ipv6 throughput-delay eigrp default <NUMBER> tens-of-micro|pico
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 417
I Commandsipv6 throughput-delay
isisisis fabric
Description: Intermediate System to Intermediate System (IS-IS)
Syntax:
Fabric IS-IS configurationfabric
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)418
I Commandsisis
isolationisolation enforce
Description: Enable EPG isolation
Syntax:
Enable enforcing of policy-control rules (EPG isolation)enforce
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# isolation enforce
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 419
I Commandsisolation
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)420
I Commandsisolation
K Commands
• key, page 422
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 421
keykey <WORD>
Description: LDAP server key for authentication
Syntax:
server key (Max Size 32)<WORD>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key <WORD>
key <WORD>
Description: RADIUS server key for authentication
Syntax:
key for authentication (Max Size 32)<WORD>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key <WORD>
key <WORD>
Description: TACACS server key for authentication
Syntax:
key for authentication (Max Size 32)<WORD>
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)422
K Commandskey
L Commands
• l2-unknown-unicast, page 425
• l3-unknown-multicast, page 426
• l3out, page 427
• l4l7-peer, page 428
• l4l7, page 429
• l4l7 cluster import-from, page 430
• l4l7 cluster name, page 431
• l4l7 graph, page 432
• label match, page 433
• label name, page 434
• lacp fast-select-hot-standby, page 435
• lacp graceful-convergence, page 436
• lacp load-defer, page 437
• lacp max-links, page 438
• lacp min-links, page 440
• lacp port-priority, page 442
• lacp port-priority interface, page 444
• lacp rate, page 445
• lacp rate fast normal interface, page 447
• lacp suspend-individual, page 448
• last-name, page 449
• ldap-server attribute, page 450
• ldap-server basedn, page 451
• ldap-server filter, page 452
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 423
• ldap-server host, page 453
• ldap-server retries, page 454
• ldap-server timeout, page 455
• leaf-group, page 456
• leaf-interface-group, page 457
• leaf-interface-profile, page 458
• leaf-policy-group, page 459
• leaf-profile, page 460
• leaf, page 461
• legacy, page 462
• link, page 463
• lldp, page 466
• lldp holdtime, page 469
• lldp reinit, page 470
• lldp timer, page 471
• local-as, page 472
• locality, page 473
• logfile, page 474
• logging, page 475
• logging audit, page 476
• logging description, page 477
• logging event, page 478
• logging fault, page 479
• logging server-group, page 480
• logging session, page 481
• logging severity, page 482
• lsp-fast-flood, page 484
• lsp-gen-interval, page 485
• lsp-mtu, page 486
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)424
L Commands
l2-unknown-unicastl2-unknown-unicast <WORD>
Description: Change Unknown Unicast flood behavior
Syntax:
Unicast Unknown threatmentWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# l2-unknown-unicast <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 425
L Commandsl2-unknown-unicast
l3-unknown-multicastl3-unknown-multicast <WORD>
Description: Change L3 Multicast flood behavior
Syntax:
IP Multicast unknown Fram handlingWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# l3-unknown-multicast <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)426
L Commandsl3-unknown-multicast
l3outl3out <WORD>
Description: Configuration for L3Out
Syntax:
L3Out name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 427
L Commandsl3out
l4l7-peerl4l7-peer tenant <WORD> out <WORD> epg <WORD> redistribute WORD
Description: Configure l3external epg association for a l4l7 graph connector.
Syntax:
tenant under which the l3external epg residestenant
WORDWORD
l3external outside nameout
WORDWORD
l3external-epg nameepg
WORDWORD
Protocol Redistribute Settingsredistribute
Protocol Redistribute SettingsWORD
Command Mode: connector : Configure Connector for a Service Node
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# connector <WORD> [cluster-interface <WORD>](config-connector)# l4l7-peer tenant <WORD> out <WORD> epg <WORD> redistribute WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)428
L Commandsl4l7-peer
l4l7l4l7 graph <WORD>
Description: Associate a l4l7 graph with this subject
Syntax:
l4l7 graph to associate withgraph
Service Graph name (Max Size 64)WORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# l4l7 graph <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 429
L Commandsl4l7
l4l7 cluster import-froml4l7 cluster import-from <WORD> device-cluster <WORD>
Description: Import a L4-L7 Service Device Cluster
Syntax:
Tenant name (Max Size 63)WORD
Device Cluster namedevice-cluster
Device cluster name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster import-from <WORD> device-cluster <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)430
L Commandsl4l7 cluster import-from
l4l7 cluster namel4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service <service>] [function <function>]
Description: Add a L4-L7 Service Device Cluster
Syntax:
Device cluster name (Max Size 64)WORD
Type of l4l7 Device Clustertype
Type of l4l7 Device Clustertype
Physical or Virtual vlan domain to use for allocating encapsvlan-domain
Physical Or Virtual vlan domain to use for allocating encaps<domain-name>
(Optional) Indicates the type of service the device cluster providesservice
(Optional) Indicates the type of function the device cluster providesfunction
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 431
L Commandsl4l7 cluster name
l4l7 graphl4l7 graph <WORD> [contract <contract-option>]
Description: Configure L4-L7 Service Graph
Syntax:
Service Graph name (Max Size 64)WORD
(Optional) Name of Contractcontract-option
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)432
L Commandsl4l7 graph
label matchlabel match provider|consumer any|one|all|none
Description: Specify the match type for the provider or consumer label
Syntax:
Matching type for providerprovider
Matching type for consumerconsumer
Match if ANY label is found in the contract relationany
Match if exactly ONE label is found in the contract relationone
Match if ALL labels are found in the contract relationall
Match if NO labels are found in the contract relationnone
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# label match provider|consumer any|one|all|none
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 433
L Commandslabel match
label namelabel name <WORD> provider|consumer
Description: Add a provider or consumer label to the subject
Syntax:
Name of the label to add (Max Size 64)WORD
Matching type for providerprovider
Matching type for consumerconsumer
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# label name <WORD> provider|consumer
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)434
L Commandslabel name
lacp fast-select-hot-standbylacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp fast-select-hot-standby
lacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp fast-select-hot-standby
lacp fast-select-hot-standby
Description: Enable LACP fast select for hot standby ports
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp fast-select-hot-standby
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 435
L Commandslacp fast-select-hot-standby
lacp graceful-convergencelacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp graceful-convergence
lacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp graceful-convergence
lacp graceful-convergence
Description: Enable LACP graceful convergence
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp graceful-convergence
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)436
L Commandslacp graceful-convergence
lacp load-deferlacp load-defer
Description: Enable LACP load defer member ports
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp load-defer
lacp load-defer
Description: Enable LACP load defer member ports
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp load-defer
lacp load-defer
Description: Enable LACP load defer member ports
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp load-defer
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 437
L Commandslacp load-defer
lacp max-linkslacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp max-links <NUMBER>
lacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp max-links <NUMBER>
lacp max-links <NUMBER>
Description: Configure maximum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)438
L Commandslacp max-links
(config-vpc-if)# lacp max-links <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 439
L Commandslacp max-links
lacp min-linkslacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp min-links <NUMBER>
lacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp min-links <NUMBER>
lacp min-links <NUMBER>
Description: Configure minimum number of links
Syntax:
Range 1 to 16. Number range from=1 to=16<number>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)440
L Commandslacp min-links
(config-vpc-if)# lacp min-links <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 441
L Commandslacp min-links
lacp port-prioritylacp port-priority <arg>
Description: Set Lacp priority
Syntax:
Priority Value. Number range from=1 to=65535arg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp port-priority <>
lacp port-priority <arg>
Description: Set Lacp priority.
Syntax:
Priority Value. Number range from=1 to=65535arg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp port-priority <>
lacp port-priority <NUMBER>
Description: Set Lacp priority.
Syntax:
Priority Value. Number range from=1 to=65535<1-65535>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)442
L Commandslacp port-priority
(config-leaf-if)# lacp port-priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 443
L Commandslacp port-priority
lacp port-priority interfacelacp port-priority <arg> interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Priority Value. Number range from=1 to=65535arg
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp port-priority <> interface ethernet
lacp port-priority <arg> interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Priority Value. Number range from=1 to=65535arg
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp port-priority <> interface ethernet
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)444
L Commandslacp port-priority interface
lacp ratelacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp rate fast|normal
lacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp rate fast|normal
lacp rate fast|normal
Description: Set Lacp rate
Syntax:
Set rate to fastfast
Set rate to normalnormal
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 445
L Commandslacp rate
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# lacp rate fast|normal
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)446
L Commandslacp rate
lacp rate fast normal interfacelacp rate fast|normal interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Set rate to fastfast
Set rate to normalnormal
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# lacp rate fast|normal interface ethernet
lacp rate fast|normal interface ethernet
Description: Set Port Priority on specific Ports
Syntax:
Set rate to fastfast
Set rate to normalnormal
Configure Physical Interfaceethernet
Provide range of Interfacesarg
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# lacp rate fast|normal interface ethernet
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 447
L Commandslacp rate fast normal interface
lacp suspend-individuallacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lacp suspend-individual
lacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lacp suspend-individual
lacp suspend-individual
Description: Enable LACP individual Port suspension
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lacp suspend-individual
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)448
L Commandslacp suspend-individual
last-namelast-name <WORD>
Description: Set The last name of the locally-authenticated user.
Syntax:
last name (Max Size 32)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# last-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 449
L Commandslast-name
ldap-server attributeldap-server attribute <WORD>
Description: An LDAP endpoint attribute to be used as the CiscoAVPair
Syntax:
LDAP endpoint attribute (Max Size 63)<WORD>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server attribute <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)450
L Commandsldap-server attribute
ldap-server basednldap-server basedn <WORD>
Description: The LDAP base DN for user lookup in the LDAP directory tree
Syntax:
user lookup in LDAP directory tree (Max Size 127)<WORD>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server basedn <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 451
L Commandsldap-server basedn
ldap-server filterldap-server filter <WORD>
Description: LDAP search filter for the LDAP endpoint
Syntax:
search filter for the LDAP endpoint (Max Size 63)<WORD>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server filter <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)452
L Commandsldap-server filter
ldap-server hostldap-server host <A.B.C.D|A:B::C:D|WORD>
Description: LDAP server DNS name or IP address
Syntax:
Provide a hostname or IPV4/IPV6 addressA.B.C.D|A:B::C:D|WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 453
L Commandsldap-server host
ldap-server retriesldap-server retries <NUMBER>
Description: Global LDAP server retransmit count
Syntax:
Global LDAP server retransmit count. Number range from=0 to=5<0-5>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)454
L Commandsldap-server retries
ldap-server timeoutldap-server timeout <NUMBER>
Description: Global LDAP server timeout period in seconds
Syntax:
Global LDAP server timeout period in seconds. Number range from=1to=60
<1-60>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# ldap-server timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 455
L Commandsldap-server timeout
leaf-groupleaf-group <WORD>
Description: Configure Leaf Group
Syntax:
Leaf Group name (Max Size 64)WORD
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)456
L Commandsleaf-group
leaf-interface-groupleaf-interface-group <WORD>
Description: Configure Leaf Interface Group
Syntax:
Leaf Interface Group name (Max Size 64)WORD
Command Mode: leaf-interface-profile : Create Leaf Interface Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 457
L Commandsleaf-interface-group
leaf-interface-profileleaf-interface-profile <WORD>
Description: Create Leaf Interface Profile
Syntax:
Leaf Interface Profile name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>
leaf-interface-profile <WORD>
Description: Attach Leaf Interface Profile to the Leaf Profile
Syntax:
Leaf Interface Profile name (Max Size 64)WORD
Command Mode: leaf-profile : Configure Leaf Profile
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-interface-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)458
L Commandsleaf-interface-profile
leaf-policy-groupleaf-policy-group <WORD>
Description: Configure leaf policy group
Syntax:
Leaf policy name (Max Size 64)WORD
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf-policy-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 459
L Commandsleaf-policy-group
leaf-profileleaf-profile <WORD>
Description: Configure Leaf Profile
Syntax:
Leaf Profile name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)460
L Commandsleaf-profile
leafleaf <101-4000>
Description: Provide a Range of Nodes
Syntax:
Leaf Range or Leaf Name List<101-4000>
Command Mode: leaf-group : Configure Leaf Group
Command Path:
# configure [['terminal', 't']](config)# leaf-profile <WORD>(config-leaf-profile)# leaf-group <WORD>(config-leaf-group)# leaf <101-4000>
leaf <101-4000>
Description: Configure Leaf Node
Syntax:
Leaf Range or Leaf Name List<101-4000>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 461
L Commandsleaf
legacylegacy forwarding vlan <NUMBER> vlan-domain <WORD>
Description: Set the bridge domain to behave as a L2 vlan in traditional ethernet environment
Syntax:
Forwarding keywordforwarding
Legacy Vlan Numbervlan
Legacy Vlan Number. Number range from=1 to=4094<1-4094>
Name of the vlan domain to usevlan-domain
Name of the vlan domain to use (Max Size 64)WORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# legacy forwarding vlan <NUMBER> vlan-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)462
L Commandslegacy
linklink debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 463
L Commandslink
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# link debounce time <NUMBER>
link debounce time <NUMBER>
Description: Configure link
Syntax:
Configure link debounce timerdebounce
Link debounce timetime
Timer value (in milliseconds). Number range from=0 to=5000<time>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)464
L Commandslink
(config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# link debounce time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 465
L Commandslink
lldplldp receive|transmit|both|default
Description: Configure Interface LLDP parameters on DVS uplink ports
Syntax:
Enable LLDP receptionreceive
Enable LLDP transmissiontransmit
Enable LLDP in both directionsboth
Remove LLDP override policydefault
Command Mode: configure-dvs : Configure a VMware Domain as DVS type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-dvs(config-vmware-dvs)# lldp receive|transmit|both|default
lldp receive|transmit|both|default
Description: Configure Interface LLDP parameters on AVS uplink ports
Syntax:
Enable LLDP receptionreceive
Enable LLDP transmissiontransmit
Enable LLDP in both directionsboth
Remove LLDP override policydefault
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# lldp receive|transmit|both|default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)466
L Commandslldp
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 467
L Commandslldp
(config-leaf-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# lldp receive|transmit
lldp receive|transmit
Description: Configure Interface LLDP parameters
Syntax:
Enable LLDP reception on interfacereceive
Enable LLDP transmission on interfacetransmit
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# lldp receive|transmit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)468
L Commandslldp
lldp holdtimelldp holdtime <NUMBER>
Description: Specify the hold time to be sent in LLDP packets
Syntax:
Holdtime in sec. Number range from=10 to=255<10-255>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# lldp holdtime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 469
L Commandslldp holdtime
lldp reinitlldp reinit <NUMBER>
Description: Specify the delay for LLDP initialization on an interface
Syntax:
Reinit Delay in sec. Number range from=1 to=10<1-10>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# lldp reinit <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)470
L Commandslldp reinit
lldp timerlldp timer <NUMBER>
Description: Specify the rate at which LLDP packets are sent
Syntax:
Rate of packets in sec. Number range from=5 to=254<5-254>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# lldp timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 471
L Commandslldp timer
local-aslocal-as <NUMBER> no-prepend|replace-as|dual-as
Description: Local Autonomous System Configuration for a BGP Peer
Syntax:
The local autonomous system number. Number range from=1to=4294967295
<1-4294967295>
Do not prepend local-as to updates from ebgp peersno-prepend
Replace real AS with local AS in the EBGP updatesreplace-as
Accept either real AS or local AS from the ebgp peerdual-as
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# local-as <NUMBER> no-prepend|replace-as|dual-as
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)472
L Commandslocal-as
localitylocality <WORD>
Description: Set The city or town of the organization.
Syntax:
city or town (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# locality <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 473
L Commandslocality
logfilelogfile [severity <severity>]
Description: Enable the logging to logfile
Syntax:
(Optional) The severity level for the logsseverity
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# logfile [severity <severity>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)474
L Commandslogfile
logginglogging server-group <WORD>
Description: Logging server group configuration mode
Syntax:
Logging Server-Group configurationserver-group
Logging server-group name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 475
L Commandslogging
logging auditlogging audit
Description: Enable audit and session logs to the policy
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging audit
logging audit
Description: Enable audit logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging audit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)476
L Commandslogging audit
logging descriptionlogging description <WORD>
Description: Add description for syslog common
Syntax:
Description (Max Size 128) surrounded by single quotesWORD
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging description <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 477
L Commandslogging description
logging eventlogging event
Description: Enable event logs to the policy
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging event
logging event
Description: Enable event logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging event
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)478
L Commandslogging event
logging faultlogging fault
Description: Enable fault logs to the policy
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging fault
logging fault
Description: Enable fault logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging fault
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 479
L Commandslogging fault
logging server-grouplogging server-group <WORD>
Description: Logging server group configuration
Syntax:
Logging server-group name (Max Size 64)WORD
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging server-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)480
L Commandslogging server-group
logging sessionlogging session
Description: Enable session logs to the policy
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging session
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 481
L Commandslogging session
logging severitylogging severity info|notice|emergency|alert|critical|error|debug|warning
Description: Configure minimum severity level for logs generated
Syntax:
Infoinfo
Noticenotice
Emergencyemergency
Alertalert
Criticalcritical
Errorerror
Debugdebug
Warningwarning
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# logging severity info|notice|emergency|alert|critical|error|debug|warning
logging severity emergencies|debugging|critical|errors|warnings|information|alerts|notifications
Description: Configure minimum severity level for logs generated
Syntax:
Emergenciesemergencies
Debuggingdebugging
Criticalcritical
Errorserrors
Warningswarnings
Informationinformation
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)482
L Commandslogging severity
Alertsalerts
Notificationsnotifications
Command Mode: syslog : Syslog common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# syslog common(config-syslog)# logging severityemergencies|debugging|critical|errors|warnings|information|alerts|notifications
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 483
L Commandslogging severity
lsp-fast-floodlsp-fast-flood
Description: Enables the ISIS LSP fast flood
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# lsp-fast-flood
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)484
L Commandslsp-fast-flood
lsp-gen-intervallsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Set the ISIS LSP generation maximal wait interval
Syntax:
Level 1level-1
LSP generation maximum wait interval. Number range from=50to=120000
<50-120000>
Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# lsp-gen-interval level-1 <NUMBER> <50-120000> <50-120000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 485
L Commandslsp-gen-interval
lsp-mtulsp-mtu <NUMBER>
Description: Set the configuration of link-state packet (LSP) maximum transmission units (MTU) value
Syntax:
The configuration of link-state packet (LSP) maximum transmissionunits (MTU).. Number range from=256 to=4352
<256-4352>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# lsp-mtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)486
L Commandslsp-mtu
M Commands
• mac-address, page 489
• match, page 491
• match arp, page 492
• match bridge-domain, page 493
• match community, page 494
• match icmp, page 495
• match ip, page 496
• match ipv6, page 497
• match prefix-list, page 498
• match raw, page 499
• match tcp, page 500
• match udp, page 501
• max-lsa, page 502
• max-validity-period, page 503
• max concurrent, page 504
• max running, page 505
• maximum-paths, page 506
• maximum-prefix, page 508
• mcp, page 509
• mcp action, page 511
• mcp enable, page 512
• mcp factor, page 513
• mcp init-delay, page 514
• mcp transmit-frequency, page 515
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 487
• member, page 516
• message-level, page 517
• message-size, page 518
• metric, page 519
• mgmt-epg, page 520
• microsoft-domain, page 521
• microsoft, page 522
• min-rx, page 523
• min-tx, page 524
• min, page 525
• mode, page 526
• modulus, page 527
• monitor, page 528
• monitor access, page 529
• monitor fabric, page 530
• monitor tenant, page 531
• monitor virtual, page 532
• mtu-ignore, page 533
• mtu, page 534
• multi-destination, page 537
• multi-site-mac-address, page 538
• multicast-address, page 539
• multiplier, page 540
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)488
M Commands
mac-addressmac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Add a custom MAC address to the bridgedomain
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# mac-addressE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description:Manually set interface MAC address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 489
M Commandsmac-address
mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure mac Address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)490
M Commandsmac-address
matchmatch dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>]
Description: Add a rule to match DSCP or DOT1P, queue the traffic and optionally mutate it
Syntax:
Match entry for DSCPdscp
Match entry for DOT1Pdot1p
From of DSCP or DOT1P rangeWORD
To of DSCP or DOT1P rangeWORD
(Optional) Set the QOS class for the trafficWORD
(Optional) DSCP rewriteWORD
Command Mode: policy-map type qos : QOS policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type qos <WORD>(config-tenant-pmap-qos)# match dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 491
M Commandsmatch
match arpmatch arp
Description:Match the ARP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match arp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)492
M Commandsmatch arp
match bridge-domainmatch bridge-domain <arg>
Description:Match subnets of a bridge-domain
Syntax:
arg
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match bridge-domain <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 493
M Commandsmatch bridge-domain
match communitymatch community <WORD>
Description: Configure community features
Syntax:
Name of communityWORD
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)494
M Commandsmatch community
match icmpmatch icmp
Description:Match the ICMP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match icmp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 495
M Commandsmatch icmp
match ipmatch ip
Description:Match the IP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match ip
match ip <A.B.C.D/LEN> [shared]
Description: Add a subnet that identify hosts being part of the epg
Syntax:
IP prefix and network mask lengthA.B.C.D/LEN
(Optional) Add the shared scope to the existing scope for the subnetshared
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# match ip <A.B.C.D/LEN> [shared]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)496
M Commandsmatch ip
match ipv6match ipv6 X:X:X:X::X/<0-128>
Description: Add a subnet that identify hosts being part of the epg
Syntax:
IPv6 prefix and network mask lengthX:X:X:X::X/<0-128>
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# match ipv6 X:X:X:X::X/<0-128>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 497
M Commandsmatch ipv6
match prefix-listmatch prefix-list <WORD>
Description:Match entries of a prefix-list
Syntax:
Name of prefix-list (Max Size 63)WORD
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)498
M Commandsmatch prefix-list
match rawmatch raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag <applyToFrag>] [dToPort<NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>] [icmpv6T <icmpv6T>] [sToPort<NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort <NUMBER>]
Description: Specify a raw vzEntry
Syntax:
Entry Name (Max Size 64)WORD
(Optional) TCP Flags as comma separated values like val1,val2,..valNtcpRules
(Optional) ARP OpcodesarpOpc
(Optional) Apply to FragmentapplyToFrag
(Optional) L4 Destination Port. Number range from=0 to=65535<0-65535>
(Optional) IP Protocol. Number range from=0 to=255<0-255>
(Optional) ICMP Typeicmpv4T
(Optional) Stateful flagstateful
(Optional) ICMPv6 Typeicmpv6T
(Optional) L4 Source Port. Number range from=0 to=65535<0-65535>
(Optional) Ethernet TypeetherT
(Optional) L4 Source Port. Number range from=0 to=65535<0-65535>
(Optional) L4 Destination Port. Number range from=0 to=65535<0-65535>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag<applyToFrag>] [dToPort <NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>][icmpv6T <icmpv6T>] [sToPort <NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort<NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 499
M Commandsmatch raw
match tcpmatch tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description:Match TCP traffic
Syntax:
(Optional) TCP Source port Range<from>-[<to>] contained in<0-65535>
(Optional) TCP Destination port Range<from>-[<to>] contained in<0-65535>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>]contained in <0-65535>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)500
M Commandsmatch tcp
match udpmatch udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description:Match UDP traffic
Syntax:
(Optional) UDP Source port Range<from>-[<to>] contained in<0-65535>
(Optional) UDP Destination port Range<from>-[<to>] contained in<0-65535>
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# access-list <WORD>(config-tenant-acl)# match udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>]contained in <0-65535>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 501
M Commandsmatch udp
max-lsamax-lsa <NUMBER> <NUMBER> reject|restart|log
Description: Feature to limit the number of non-self-originated LSAs
Syntax:
Set maximum number of non self-generated LSAs. Number rangefrom=1 to=4294967295
<1-4294967295>
Threshold value (%) at which to generate a warning message. Numberrange from=1 to=100
<1-100>
Reject LSAs beyond the limitreject
Restart the neighborrestart
log a warninglog
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)502
M Commandsmax-lsa
max-validity-periodmax-validity-period <NUMBER>
Description: Set The maximum validity period for a webtoken
Syntax:
Set Themaximumvalidity period for a webtoken. Number range from=4to=24
<4-24>
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# max-validity-period <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 503
M Commandsmax-validity-period
max concurrentmax concurrent nodes <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
Maximum number of tasks that can be processed concurrently.nodes
Enter maximum number of concurrent nodes. 0 for unlimited. Numberrange from=0 to=65535
<0-65535>
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# max concurrent nodes <NUMBER>
max concurrent nodes <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
Maximum number of tasks that can be processed concurrently.nodes
Enter maximum number of concurrent nodes. 0 for unlimited. Numberrange from=0 to=65535
<0-65535>
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# max concurrent nodes <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)504
M Commandsmax concurrent
max runningmax running time <TIME>
Description: Set the window maximum running time
Syntax:
Maximum running timetime
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimitedTIME
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# max running time <TIME>
max running time <TIME>
Description: Set the window maximum running time
Syntax:
Maximum running time in millisecondstime
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimitedTIME
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# max running time <TIME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 505
M Commandsmax running
maximum-pathsmaximum-paths <NUMBER>
Description: Set the maximum ECMP for the OSPF protocol
Syntax:
Maximum paths. Number range from=1 to=64<1-64>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# maximum-paths <NUMBER>
maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
Maximum Path Limit. Number range from=1 to=32<1-32>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>
maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
Maximum Path Limit. Number range from=1 to=32<1-32>
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)506
M Commandsmaximum-paths
(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# maximum-paths <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 507
M Commandsmaximum-paths
maximum-prefixmaximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]
Description:Maximum number of prefixes from this neighbor
Syntax:
Max. prefix limit. Number range from=1 to=300000<1-300000>
(Optional) Action to be performed when the maximum prefix limit isreached
<action>
(Optional) The threshold % of the maximum number of prefixes beforea warning is issued. Number range from=1 to=100
<1-100>
(Optional) The period of time in minutes before restarting the peer whenthe prefix limit is reached. Number range from=1 to=65535
<1-65535>
Command Mode: address-family : Configure an address-family for peer
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold<NUMBER>] [restart-time <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)508
M Commandsmaximum-prefix
mcpmcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# mcp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 509
M Commandsmcp
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# mcp enable
mcp enable
Description: Configure MCP interface parameters
Syntax:
Configure MCP parametersenable
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# mcp enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)510
M Commandsmcp
mcp actionmcp action port-disable
Description: Configure MCP Loop Protection Action
Syntax:
Disable the port when MCP detects loopport-disable
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp action port-disable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 511
M Commandsmcp action
mcp enablemcp enable key <WORD>
Description: Enable/Disable MCP Protocol
Syntax:
Configure MCP keykey
MCP keyWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp enable key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)512
M Commandsmcp enable
mcp factormcp factor <NUMBER>
Description: Configure MCP Loop Detection Factor
Syntax:
MCP Loop Detection Multipication Factor. Number range from=1to=255
<1-255>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp factor <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 513
M Commandsmcp factor
mcp init-delaymcp init-delay <NUMBER>
Description: Configure MCP Loop Detection Init Delay Time
Syntax:
MCP Loop Detection Init Delay Time. Number range from=0 to=1800<0-1800>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp init-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)514
M Commandsmcp init-delay
mcp transmit-frequencymcp transmit-frequency <NUMBER>
Description: Configure MCP Advertisement Transmit Frequency
Syntax:
MCP Advertisement Tx Frequency. Number range from=2 to=300<2-300>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# mcp transmit-frequency <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 515
M Commandsmcp transmit-frequency
membermember device <WORD> device-interface <WORD>
Description: Configure Cluster Interface Member
Syntax:
Cluster Devicedevice
Cluster Device name (Max Size 64)WORD
Cluster Device Interfacedevice-interface
Cluster Device Interface (Max Size 256)WORD
Command Mode: cluster-interface : Configure L4-L7 Cluster Interface
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)516
M Commandsmember
message-levelmessage-level info|notice|emergency|alert|critical|error|debug|warning
Description: Configure the urgency of the message
Syntax:
Infoinfo
Noticenotice
Emergencyemergency
Alertalert
Criticalcritical
Errorerror
Debugdebug
Warningwarning
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# message-levelinfo|notice|emergency|alert|critical|error|debug|warning
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 517
M Commandsmessage-level
message-sizemessage-size <NUMBER>
Description: configure the size of the message
Syntax:
The size of the messages. Number range from=0 to=5000000<size>
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# destination <WORD>(config-callhome-destnprof-destn)# message-size <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)518
M Commandsmessage-size
metricmetric version 64bit
Description: Set EIGRP Metric Style
Syntax:
Metric Styleversion
wide metric64bit
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# metric version 64bit
metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
Metric Styleversion
wide metric64bit
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# metric version 64bit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 519
M Commandsmetric
mgmt-epgmgmt-epg in-band|out-of-band <WORD>
Description: Select remote path management EPG
Syntax:
In-Band EPGin-band
Out-of-Band EPGout-of-band
Management EPG nameWORD
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# mgmt-epg in-band|out-of-band <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)520
M Commandsmgmt-epg
microsoft-domainmicrosoft-domain <WORD>
Description: Create a VMMMicrosoft Domain
Syntax:
VMMMicrosoft Domain nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# microsoft-domain <WORD>
microsoft-domain member <WORD> [encap <WORD>] [deploy <WORD>] [push <WORD>]
Description: Associate EPG to a Microsoft Domain
Syntax:
Bind the EPG to a Microsoft domainmember
Microsoft Domain NameWORD
(Optional) Enforce encap value. (For example vlan-10 or auto)WORD
(Optional) Deployment modeWORD
(Optional) Push modeWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft-domain member <WORD> [encap <WORD>] [deploy <WORD>] [push<WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 521
M Commandsmicrosoft-domain
microsoftmicrosoft static-ip-pool <name> gateway <gwAddress>
Description: Configure static ip pool
Syntax:
Configure the static IP poolstatic-ip-pool
enter the name of the static IP poolname
Configure gateway address on interfacegateway
gwAddressgwAddress
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)522
M Commandsmicrosoft
min-rxmin-rx <NUMBER>
Description: Configure BFD MIN-RX value in milliseconds
Syntax:
BFD interval. Number range from=50 to=999<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# min-rx <NUMBER>
min-rx <NUMBER>
Description: Configure required Minimum Rx Interval in milliseconds
Syntax:
Minimum Rx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# min-rx <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 523
M Commandsmin-rx
min-txmin-tx <NUMBER>
Description: Configure BFD MIN-TX value in milliseconds
Syntax:
BFD interval. Number range from=50 to=999<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# min-tx <NUMBER>
min-tx <NUMBER>
Description: Configure required Minimum Tx Interval in milliseconds
Syntax:
Minimum Tx Interval. Number range from=50 to=999<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# min-tx <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)524
M Commandsmin-tx
minmin buffer <0-3>
Description: Set the minimum number of buffer of MTU size to be reserved
Syntax:
Number of minim buffers to reservebuffer
Number of minim buffers to reserve<0-3>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# min buffer <0-3>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 525
M Commandsmin
modemode atomic|best-effort
Description: Snapshot import mode atomic|best-effort
Syntax:
Atomic modeatomic
Best Effort modebest-effort
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# mode atomic|best-effort
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)526
M Commandsmode
modulusmodulus <modulus>
Description: Set the length of the encryption keys
Syntax:
<modulus><modulus>
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# modulus <modulus>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 527
M Commandsmodulus
monitormonitor virtual session <WORD>
Description: Configure a monitor session
Syntax:
virtualvirtual
sessionsession
session name (Max Size 64)WORD
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# monitor virtual session <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)528
M Commandsmonitor
monitor accessmonitor access session <session_name>
Description: Configue monitor session for access interfaces
Syntax:
sessionsession
session name (Max Size 64)session_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 529
M Commandsmonitor access
monitor fabricmonitor fabric session <session_name>
Description: Configue monitor session for fabric interfaces
Syntax:
sessionsession
session name (Max Size 64)session_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)530
M Commandsmonitor fabric
monitor tenantmonitor tenant <tenant_name> session <session_name>
Description: Configue monitor session for tenant EPGs
Syntax:
tenant name (Max Size 63)tenant_name
sessionsession
session name (Max Size 64)session_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 531
M Commandsmonitor tenant
monitor virtualmonitor virtual session <WORD>
Description: Configure monitor session for virtual switches
Syntax:
sessionsession
Session name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)532
M Commandsmonitor virtual
mtu-ignoremtu-ignore
Description: Set OSPF Interface Policy Controls
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# mtu-ignore
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 533
M Commandsmtu-ignore
mtumtu <1500-9216>
Description: Set the MTU for this class of service
Syntax:
MTU value<1500-9216>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# mtu <1500-9216>
mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
Interface MTU. Number range from=576 to=9000<576-9000>
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# mtu <NUMBER>
mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
Interface MTU. Number range from=576 to=9000<576-9000>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)534
M Commandsmtu
(config-leaf-if)# mtu <NUMBER>
mtu <mtu>
Description:MTU size
Syntax:
mtu value. Number range from=64 to=9216mtu
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-access-dest)# mtu <mtu>
mtu <mtu>
Description:MTU size
Syntax:
mtu value. Number range from=64 to=9216mtu
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>(config-monitor-fabric-dest)# mtu <mtu>
mtu <arg>
Description:MTU size
Syntax:
mtu value. Number range from=64 to=9216arg
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# destination tenant <tenant_name> application <application_name>epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 535
M Commandsmtu
(config-monitor-tenant-dest)# mtu <>
mtu <arg>
Description: Configure MTU size
Syntax:
MTU value. Number range from=64 to=9216arg
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# destination destip <A.B.C.D>(config-monitor-virtual-remote-dest)# mtu <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)536
M Commandsmtu
multi-destinationmulti-destination <WORD>
Description: Change behavior for multi destination flood
Syntax:
Unknown multicast MAC and Broadcast handlingWORD
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# multi-destination <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 537
M Commandsmulti-destination
multi-site-mac-addressmulti-site-mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure multi-site MAC address
Syntax:
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# multi-site-mac-addressE.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)538
M Commandsmulti-site-mac-address
multicast-addressmulticast-address <IP>
Description: Configure outgoing multicast IP address for VXLAN modes
Syntax:
Multicast IPIP
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# multicast-address <IP>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 539
M Commandsmulticast-address
multipliermultiplier <NUMBER>
Description: Configure BFD MULTIPLIER value
Syntax:
BFD interval. Number range from=1 to=50<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# multiplier <NUMBER>
multiplier <NUMBER>
Description: Configure detection multiplier
Syntax:
Detection multiplier. Number range from=1 to=50<interval>
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# multiplier <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)540
M Commandsmultiplier
N Commands
• name-lookup, page 542
• negotiate, page 543
• neighbor, page 545
• network, page 546
• next-hop-self, page 547
• ntp, page 548
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 541
name-lookupname-lookup
Description: Display OSPF router ids as DNS names
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# name-lookup
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)542
N Commandsname-lookup
negotiatenegotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# negotiate auto
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 543
N Commandsnegotiate
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# negotiate auto
negotiate auto
Description: Configure link negotiation parameters
Syntax:
Configure auto-negotiationauto
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# negotiate auto
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)544
N Commandsnegotiate
neighborneighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>]
Description: Configure a BGP neighbor
Syntax:
IP address of the neighborA.B.C.D
IP prefix for neighborsA.B.C.D/LEN
IPv6 address of the neighborA:B::C:D
IPv6 prefix for neighborsA:B::C:D/LEN
(Optional) Route-Map Name (API-configured L3Out Name)WORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 545
N Commandsneighbor
networknetwork bcast|p2p|unspecified
Description: Set OSPF interface policy network type
Syntax:
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
bcast
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
p2p
The OSPF interface policy network type. OSPF supports point-to-pointand broadcast.
unspecified
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# network bcast|p2p|unspecified
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)546
N Commandsnetwork
next-hop-selfnext-hop-self
Description: Set our peering address as nexthop
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# next-hop-self
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 547
N Commandsnext-hop-self
ntpntp
Description: Configure the default ntp policy
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)548
N Commandsntp
O Commands
• oob-mgmt, page 550
• oob-mgmt epg, page 551
• optimize, page 552
• option, page 553
• org-name, page 554
• org-unit-name, page 555
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 549
oob-mgmtoob-mgmt epg <epgval>
Description: Creates/Modify the out of band mgmt under the tenant mgmt
Syntax:
epg is keyword ,refers to out of band epgepg
epg name for the out of band epg created/modified under tenant mgmtepgval
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)550
O Commandsoob-mgmt
oob-mgmt epgoob-mgmt epg <WORD>
Description: Associate node to a Out of band EPG
Syntax:
Out of band End Point Group NameWORD
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface mgmt0(config-controller-if)# oob-mgmt epg <WORD>
oob-mgmt epg <WORD>
Description: Associate node to a Out of band EPG
Syntax:
Out of band End Point Group NameWORD
Command Mode: interface mgmt0 : Out of band management interface
Command Path:
# configure [['terminal', 't']](config)# switch(config-switch)# interface mgmt0(config-switch-if)# oob-mgmt epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 551
O Commandsoob-mgmt epg
optimizeoptimize subinterface
Description: Disable sub-interface optimization
Syntax:
subinterfacesubinterface
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# optimize subinterface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)552
O Commandsoptimize
optionoption <WORD> id <NUMBER> data <WORD>
Description: Add or modify an existing DHCP option when relayed from the server to the client
Syntax:
Name of the option to add (Max Size 64)WORD
ID of the optionid
ID of the option. Number range from=0 to=255<0-255>
Body of the Option TLV as hex stringdata
Body of the Option TLV as hex string, surrounded by single quotes ex:'foo*' (Max Size 256)
WORD
Command Mode: template dhcp option : Create a DHCP Option policy
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp option policy <WORD>(config-tenant-template-dhcp-option)# option <WORD> id <NUMBER> data <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 553
O Commandsoption
org-nameorg-name <WORD>
Description: Set The full legal name of the organization.
Syntax:
legal name of organization (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# org-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)554
O Commandsorg-name
org-unit-nameorg-unit-name <WORD>
Description: Set the department or unit name within the organization
Syntax:
department or unit name (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# org-unit-name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 555
O Commandsorg-unit-name
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)556
O Commandsorg-unit-name
P Commands
• passive-interface, page 559
• passphrase, page 560
• password, page 561
• password change-count, page 563
• password change-during-interval, page 564
• password change-interval, page 565
• password history-count, page 566
• password no-change-interval, page 567
• password pwd-strength-check, page 568
• path, page 569
• peer-dead-interval, page 570
• periodic-inventory notification, page 571
• phone-contact, page 572
• phone, page 573
• pod, page 574
• policy-group, page 575
• policy-map, page 577
• policy-map type data-plane, page 578
• policy-map type qos, page 579
• port, page 580
• porttrack delay, page 583
• porttrack minlinks, page 584
• porttrack state, page 585
• power, page 586
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 557
• prefix-suppression, page 587
• preview, page 588
• priority, page 589
• priv-type, page 590
• priv, page 591
• private-as-control, page 592
• protocol, page 593
• pwd-lifetime, page 594
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)558
P Commands
passive-interfacepassive-interface
Description: Set OSPF Interface Policy Controls
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# passive-interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 559
P Commandspassive-interface
passphrasepassphrase <WORD>
Description: Configure passphrase for AES encryption
Syntax:
Passphrase for AES encryption (Range of chars: 16-32) in quotes (MaxSize 32)
WORD
Command Mode: crypto aes : AES encryption configuration
Command Path:
# configure [['terminal', 't']](config)# crypto aes(config-aes)# passphrase <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)560
P Commandspassphrase
passwordpassword <WORD>
Description: Set The system user password.
Syntax:
Change user password (Max Size 256) - Only for admin useWORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# password <WORD>
password <WORD>
Description: Set The new password.
Syntax:
new password<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# password <WORD>
password WORD
Description: Configure a password for neighbor
Syntax:
Enter Clear-text passwordWORD
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 561
P Commandspassword
(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# password WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)562
P Commandspassword
password change-countpassword change-count <NUMBER>
Description: Set the number of password changes allowed within change interval
Syntax:
Set the number of password changes allowed within change interval.Number range from=0 to=10
<0-10>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 563
P Commandspassword change-count
password change-during-intervalpassword change-during-interval <change-during-interval>
Description: Set change count/interval policy selector for enforcing password change.
Syntax:
<change-during-interval><change-during-interval>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-during-interval <change-during-interval>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)564
P Commandspassword change-during-interval
password change-intervalpassword change-interval <NUMBER>
Description: Set time interval for limiting the number of password changes (unit: Hours)
Syntax:
Set A time interval for limiting the number of password changes (unit:Hours). Number range from=1 to=745
<1-745>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password change-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 565
P Commandspassword change-interval
password history-countpassword history-count <NUMBER>
Description: Set number of retired passwords to store in user's history.
Syntax:
Set number of retired passwords to store in user history.. Number rangefrom=0 to=15
<0-15>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password history-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)566
P Commandspassword history-count
password no-change-intervalpassword no-change-interval <NUMBER>
Description: Set minimum period before which user cannot change password again (unit: hours)
Syntax:
Set minimum period before which user cannot change password again(unit: hours). Number range from=1 to=745
<1-745>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password no-change-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 567
P Commandspassword no-change-interval
password pwd-strength-checkpassword pwd-strength-check
Description: Enforces the strength of password for all users
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# password pwd-strength-check
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)568
P Commandspassword pwd-strength-check
pathpath ftp|sftp|scp <HOST> [port <NUMBER>] [remote-directory <PATH>]
Description: Configure remote path properties
Syntax:
FTPftp
Secure FTPsftp
Secure copyscp
Remote host name or IP addressHOST
(Optional) Remote port. Number range from=0 to=65535<0-65535>
(Optional) Remote directory: path/to/some/dirPATH
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# path ftp|sftp|scp <HOST> [port <NUMBER>] [remote-directory <PATH>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 569
P Commandspath
peer-dead-intervalpeer-dead-interval <NUMBER>
Description: Configure Peer dead Interval
Syntax:
Peer dead Interval value. Number range from=5 to=600<5-600>
Command Mode: vpc domain explicit : Pair two leaf nodes explicitly
Command Path:
# configure [['terminal', 't']](config)# vpc domain explicit <NUMBER> leaf <101-4000> <101-4000>(config-vpc)# peer-dead-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)570
P Commandspeer-dead-interval
periodic-inventory notificationperiodic-inventory notification schedule <schedName>
Description: Configure periodic notifications Parameters
Syntax:
Configure periodic notification schedulerschedule
scheduler name<schedName>
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# periodic-inventory notification schedule <schedName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 571
P Commandsperiodic-inventory notification
phone-contactphone-contact <WORD>
Description: The contact phone number
Syntax:
Phone number in international format(such as +1-800-123-4567) (MaxSize 512)
WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# phone-contact <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)572
P Commandsphone-contact
phonephone <WORD>
Description: Set The phone number of the locally-authenticated user.
Syntax:
phone number (Max Size 512)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# phone <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 573
P Commandsphone
podpod 1
Description: Pod configuration mode
Syntax:
Enter Pod ID1
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# pod 1
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)574
P Commandspod
policy-grouppolicy-group <WORD>
Description: Associate an Interface Policy Group to this Interface Group
Syntax:
Interface Policy Group Name (Max Size 64)WORD
Command Mode: leaf-interface-group : Configure Leaf Interface Group
Command Path:
# configure [['terminal', 't']](config)# leaf-interface-profile <WORD>(config-leaf-if-profile)# leaf-interface-group <WORD>(config-leaf-if-group)# policy-group <WORD>
policy-group <WORD>
Description: Configure Policy Group on the Fex
Syntax:
Interface Policy Group Name (Max Size 64)WORD
Command Mode: fex-interface-group : Configure Fex Interface Group
Command Path:
# configure [['terminal', 't']](config)# fex-profile <WORD>(config-fex-profile)# fex-interface-group <WORD>(config-fex-if-group)# policy-group <WORD>
policy-group <WORD> [force]
Description: Configure Policy Group
Syntax:
Interface Policy Group Name (Max Size 64)WORD
(Optional) Delete Per Port Configuration and apply the existingpolicy-group config
force
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 575
P Commandspolicy-group
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# policy-group <WORD> [force]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)576
P Commandspolicy-group
policy-mappolicy-map type data-plane <WORD>
Description: Create a policymap of DataPlane type to police/reclassify the traffic
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Name of the policy-map to add (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 577
P Commandspolicy-map
policy-map type data-planepolicy-map type data-plane <WORD>
Description: data-plane policy type
Syntax:
Policy Typetype
Name of the policy-map to add (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)578
P Commandspolicy-map type data-plane
policy-map type qospolicy-map type qos <WORD>
Description: QOS policy type
Syntax:
Policy Typetype
Name of the policy-map to add (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type qos <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 579
P Commandspolicy-map type qos
portport <NUMBER>
Description: LDAP server port for authentication
Syntax:
Port number. Number range from=1 to=65535<1-65535>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>
port <NUMBER>
Description: RADIUS server port for authentication
Syntax:
RADIUS server port for authentication. Number range from=1 to=65535<1-65535>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>
port <NUMBER>
Description: TACACS server port for authentication
Syntax:
RADIUS server port for authentication. Number range from=1 to=65535<1-65535>
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# port <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)580
P Commandsport
port <NUMBER>
Description: Set the port used for SSH communication service.
Syntax:
Set the port used for SSH communication service.. Number rangefrom=0 to=65535
<0-65535>
Command Mode: ssh-service : SSH communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service(config-ssh-service)# port <NUMBER>
port <NUMBER>
Description: Set the port used for TELNET communication service.
Syntax:
Set the port used for TELNET communication service.. Number rangefrom=0 to=65535
<0-65535>
Command Mode: telnet : TELNET communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet(config-telnet)# port <NUMBER>
port <NUMBER>
Description: Set the port used for HTTP communication service.
Syntax:
Set the port used for HTTP communication service.. Number rangefrom=1 to=65535
<1-65535>
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# port <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 581
P Commandsport
port <NUMBER>
Description: Set the port used for HTTPS communication service
Syntax:
Set the port used for HTTPS communication service. Number rangefrom=1 to=65535
<1-65535>
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# port <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)582
P Commandsport
porttrack delayporttrack delay <1-300>
Description: Set Port Tracking Delay
Syntax:
Delay value<1-300>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# porttrack delay <1-300>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 583
P Commandsporttrack delay
porttrack minlinksporttrack minlinks <0-12>
Description: Set Port Tracking minimum links left up before trigger
Syntax:
Minlinks Value<0-12>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# porttrack minlinks <0-12>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)584
P Commandsporttrack minlinks
porttrack stateporttrack state on
Description: Set Port Tracking State
Syntax:
To enable port tracking stateon
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# porttrack state on
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 585
P Commandsporttrack state
powerpower redundancy-policy <WORD>
Description: Create a power supply redundancy policy
Syntax:
Create a power supply redundancy policyredundancy-policy
Power supply redundancy policy name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# power redundancy-policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)586
P Commandspower
prefix-suppressionprefix-suppression
Description: Suppress prefixes
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# prefix-suppression
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 587
P Commandsprefix-suppression
previewpreview
Description: Rollback preview mode
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# preview
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)588
P Commandspreview
prioritypriority <NUMBER>
Description: Set OSPF interface priority used to determine the designated router (DR) on a specific network
Syntax:
OSPF priority. Number range from=0 to=255<0-255>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# priority <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 589
P Commandspriority
priv-typepriv-type <privType>
Description: Set the AAA domain role to set privilege bitmask of a user domain
Syntax:
<privType><privType>
Command Mode: role : Create the AAA domain role to set privilege bitmask of a user domain
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>(config-domain)# role <WORD>(config-role)# priv-type <privType>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)590
P Commandspriv-type
privpriv <privileges>
Description: Set privileges (comma separated values)
Syntax:
Privileges as comma separated values like val1,val2,..valN<privileges>
Command Mode: rbac role : Create AAA role, attributes and privileges for user authorization
Command Path:
# configure [['terminal', 't']](config)# rbac role <WORD>(config-role)# priv <privileges>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 591
P Commandspriv
private-as-controlprivate-as-control remove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as
Description: Private AS Control
Syntax:
Remove private ASremove-exclusive
Remove all private ASremove-exclusive-all
Replace private AS with local ASremove-exclusive-all-replace-as
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# private-as-controlremove-exclusive|remove-exclusive-all|remove-exclusive-all-replace-as
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)592
P Commandsprivate-as-control
protocolprotocol <protocol>
Description: RADIUS server protocol for authentication
Syntax:
<protocol><protocol>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# protocol <protocol>
protocol <WORD>
Description: Set the TACACS+ authentication protocol
Syntax:
TACACS+ authentication protocolWORD
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# protocol <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 593
P Commandsprotocol
pwd-lifetimepwd-lifetime <NUMBER>
Description: Set The lifetime of the user password (0 = No password expiration)
Syntax:
lifetime of locally-authenticated user password. Number range from=0to=3650
<0-3650>
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# pwd-lifetime <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)594
P Commandspwd-lifetime
Q Commands
• qos parameters, page 596
• qos preserve, page 597
• query-cluster-health, page 598
• query-cluster-statistics, page 599
• query-cluster-validation, page 600
• query-profile, page 601
• query, page 602
• queue control, page 603
• queue limit, page 604
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 595
qos parametersqos parameters level1|level2|level3
Description: Configure the global QOS policies
Syntax:
Set parameters for level1level1
Set parameters for level2level2
Set parameters for level3level3
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)596
Q Commandsqos parameters
qos preserveqos preserve cos
Description: Preserve incoming qos value in the frame
Syntax:
IEEE 802.1P class of service.cos
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# qos preserve cos
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 597
Q Commandsqos preserve
query-cluster-healthquery-cluster-health
Description: Re-query for Cluster Health
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# query-cluster-health
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)598
Q Commandsquery-cluster-health
query-cluster-statisticsquery-cluster-statistics
Description: Re-query for Cluster Statistics
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# query-cluster-statistics
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 599
Q Commandsquery-cluster-statistics
query-cluster-validationquery-cluster-validation
Description: Re-query for Cluster Validation
Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# query-cluster-validation
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)600
Q Commandsquery-cluster-validation
query-profilequery-profile
Description: Configure Query profile Parameters
Command Mode: callhome : Callhome common policy configuration mode
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 601
Q Commandsquery-profile
queryquery <WORD> type dn|class <dn/classname>
Description: Configure Query profile Parameters
Syntax:
Query name (Max Size 16)WORD
typetype
Dndn
Classclass
The class or DN name<dn/classname>
Command Mode: query-profile : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)602
Q Commandsquery
queue controlqueue control dynamic
Description: Set the queueing control method
Syntax:
Dynamic allocation of queue resourcesdynamic
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# queue control dynamic
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 603
Q Commandsqueue control
queue limitqueue limit <1500-9216>
Description: Set the limit for the policing queue
Syntax:
Queue limit size<1500-9216>
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# queue limit <1500-9216>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)604
Q Commandsqueue limit
R Commands
• radius-server host, page 607
• radius-server retries, page 608
• radius-server timeout, page 609
• rbac role, page 610
• rbac rule, page 611
• rbac security-domain, page 612
• realm, page 613
• recurring, page 614
• redirect, page 615
• redistribute, page 616
• redundancy-mode, page 617
• region, page 618
• reload controller, page 619
• reload switch, page 620
• remote-as, page 621
• remote, page 622
• request-status-count, page 624
• reset-to-factory, page 625
• response-incl, page 626
• response-subtree, page 627
• retransmit-interval, page 628
• retries, page 629
• revision, page 630
• role, page 631
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 605
• route-map, page 632
• route-profile, page 633
• route-reflector, page 634
• router-id, page 635
• router bgp, page 636
• router eigrp, page 637
• router ospf, page 638
• rtr-cfg, page 639
• run-mode, page 640
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)606
R Commands
radius-server hostradius-server host <A.B.C.D|A:B::C:D|WORD>
Description: RADIUS server's DNS name or its IP address
Syntax:
Provide a hostname or IPV4/IPV6 addressA.B.C.D|A:B::C:D|WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 607
R Commandsradius-server host
radius-server retriesradius-server retries <NUMBER>
Description: Global RADIUS server retransmit count
Syntax:
Global RADIUS server retransmit count. Number range from=0 to=5<0-5>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# radius-server retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)608
R Commandsradius-server retries
radius-server timeoutradius-server timeout <NUMBER>
Description: Global RADIUS server timeout period in seconds
Syntax:
Global RADIUS server timeout period in seconds. Number range from=1to=60
<1-60>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# radius-server timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 609
R Commandsradius-server timeout
rbac rolerbac role <WORD>
Description: Create AAA role, attributes and privileges for user authorization
Syntax:
Provide AAA Security domain role name (Max Size 32)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# rbac role <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)610
R Commandsrbac role
rbac rulerbac rule <DN> <WORD>
Description: Create RBAC rule, security domain users can read subtree starting at specific object
Syntax:
Provide RBAC Rule ObjectDN stringDN
Provide RBAC Rule domain name (Max Size None)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# rbac rule <DN> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 611
R Commandsrbac rule
rbac security-domainrbac security-domain <WORD>
Description: Create AAA security domain for processing authentication requests.
Syntax:
Provide AAA Security domain name (Max Size 32)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# rbac security-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)612
R Commandsrbac security-domain
realmrealm <realm>
Description: Specify server realm
Syntax:
<realm><realm>
Command Mode: aaa authentication login console : Configure console methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login console(config-console)# realm <realm>
realm <realm>
Description: Specify server realm
Syntax:
<realm><realm>
Command Mode: aaa authentication login default : Configure default methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login default(config-default)# realm <realm>
realm <realm>
Description: Specify server realm
Syntax:
<realm><realm>
Command Mode: aaa authentication login domain : Configure domain methods
Command Path:
# configure [['terminal', 't']](config)# aaa authentication login domain <WORD>(config-domain)# realm <realm>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 613
R Commandsrealm
recurringrecurring window <WORD>
Description: Recurring window configuration mode
Syntax:
Configure a schedule windowwindow
Window name (Max size 31)WORD
Command Mode: scheduler : Scheduler configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)614
R Commandsrecurring
redirectredirect
Description: Enable the state of the HTTP redirect state
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# redirect
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 615
R Commandsredirect
redistributeredistribute ospf|eigrp route-map <WORD>
Description: Redistribute route map
Syntax:
Redistribute OSPFospf
Redistribute EIGRPeigrp
Route map to redistribute toroute-map
Route map nameWORD
Command Mode: vrf : Virtual Router Context
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# redistribute ospf|eigrp route-map <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)616
R Commandsredistribute
redundancy-moderedundancy-mode combined|ps-redundant|redundant
Description: Configure power supply redundancy mode
Syntax:
Combined mode to use output of all available PScombined
PS redundant mode (N+1) to enable power output redundancyps-redundant
Redundant mode (N+N) for a single PS to power the systemredundant
Command Mode: power : Create a power supply redundancy policy
Command Path:
# configure [['terminal', 't']](config)# power redundancy-policy <WORD>(config-power)# redundancy-mode combined|ps-redundant|redundant
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 617
R Commandsredundancy-mode
regionregion <WORD>
Description: STP MST region configuration mode
Syntax:
MST region nameWORD
Command Mode: spanning-tree : STP MST configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)618
R Commandsregion
reload controllerreload controller <NUMBER>
Description: Reload controller
Syntax:
Controller id. Number range from=1 to=32<1-32>
Command Mode: exec : Exec Mode
Command Path:
# reload controller <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 619
R Commandsreload controller
reload switchreload switch <NUMBER>
Description: Reload switch
Syntax:
Switch id. Number range from=101 to=4000<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# reload switch <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)620
R Commandsreload switch
remote-asremote-as <NUMBER>
Description: Specify Autonomous System Number of the neighbor
Syntax:
The Remote autonomous system number. Number range from=1to=4294967295
<1-4294967295>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# remote-as <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 621
R Commandsremote-as
remoteremote path <WORD>
Description: Remote path configuration mode
Syntax:
Configure remote pathpath
Remote path configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get downloaded from
Syntax:
Assign remote pathpath
Remote path nameWORD
Command Mode: snapshot download : Configuration snapshot download setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot download <WORD>(config-download)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get exported to
Syntax:
Configure remote pathpath
Remote path nameWORD
Command Mode: snapshot export : Configuration export setup mode
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)622
R Commandsremote
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get imported from
Syntax:
Assign remote pathpath
Remote path nameWORD
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>(config-import)# remote path <WORD>
remote path <WORD>
Description: Set the remote path configuration will get uploaded to
Syntax:
Assign remote pathpath
Remote path nameWORD
Command Mode: snapshot upload : Configuration snapshot upload setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot upload <WORD>(config-upload)# remote path <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 623
R Commandsremote
request-status-countrequest-status-count <NUMBER>
Description: Set the maximum count of HTTP requests to track.
Syntax:
Set the maximum count of HTTP requests to track.. Number rangefrom=0 to=10240
<count>
Command Mode: http : HTTP communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# http(config-http)# request-status-count <NUMBER>
request-status-count <NUMBER>
Description: Set the maximum count of HTTPS requests to track
Syntax:
Set the maximum count of HTTPS requests to track.. Number rangefrom=0 to=10240
<count>
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# request-status-count <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)624
R Commandsrequest-status-count
reset-to-factoryreset-to-factory
Description: Reset role to factory default privileges
Command Mode: rbac role : Create AAA role, attributes and privileges for user authorization
Command Path:
# configure [['terminal', 't']](config)# rbac role <WORD>(config-role)# reset-to-factory
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 625
R Commandsreset-to-factory
response-inclresponse-incl <respincl>
Description: Configure response subtree which needs to be included
Syntax:
The response subtree to be included<respincl>
Command Mode: query : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# response-incl <respincl>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)626
R Commandsresponse-incl
response-subtreeresponse-subtree full|children|no
Description: Configure response-subtree
Syntax:
Fullfull
Childrenchildren
Nono
Command Mode: query : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# response-subtree full|children|no
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 627
R Commandsresponse-subtree
retransmit-intervalretransmit-interval <NUMBER>
Description: Set the interval between LSA retransmissions
Syntax:
Interval in seconds. Number range from=1 to=65535<1-65535>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# retransmit-interval <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)628
R Commandsretransmit-interval
retriesretries <NUMBER>
Description: LDAP server retries for authentication
Syntax:
LDAP server retries for authentication. Number range from=0 to=5<0-5>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <NUMBER>
retries <0-5>
Description: RADIUS server retries for authentication
Syntax:
RADIUS server retries for authentication<0-5>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <0-5>
retries <NUMBER>
Description: TACACS server retries for authentication
Syntax:
TACACS server retries for authentication. Number range from=0 to=5<0-5>
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 629
R Commandsretries
revisionrevision <NUMBER>
Description: Set the MST region revision number
Syntax:
MST region revision number. Number range from=0 to=65535<0-65535>
Command Mode: region : STP MST region configuration mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration(config-stp)# region <WORD>(config-stp-region)# revision <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)630
R Commandsrevision
rolerole <WORD>
Description: Create the AAA domain role to set privilege bitmask of a user domain
Syntax:
User roleWORD
Command Mode: domain : Create the AAA domain to which the user belongs.
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# domain <WORD>(config-domain)# role <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 631
R Commandsrole
route-maproute-map <WORD>
Description: Create route-map or enter route-map command mode
Syntax:
Route-map name (Max Size 64)WORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>
route-map <WORD> in|out
Description: Apply route-map to neighbor
Syntax:
Route Map Name (Max Size 63)WORD
Apply policy to incoming routesin
Apply policy to outgoing routesout
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# route-map <WORD> in|out
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)632
R Commandsroute-map
route-profileroute-profile <WORD>
Description: Configure route-profile
Syntax:
Route profile nameWORD
Command Mode: vrf : Configuration for vrf
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>
route-profile <WORD>
Description: Configure route-profile for bridge-domain
Syntax:
Route profile nameWORD
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# interface bridge-domain <WORD>(config-tenant-interface)# route-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 633
R Commandsroute-profile
route-reflectorroute-reflector spine <LIST> [description <TEXT>]
Description: Configure BGP route-reflectors
Syntax:
Configure Spines as route-reflectorsspine
Route-reflector spine node name or ID list. Ex. spine1 or 103,105LIST
(Optional) DescriptionTEXT
Command Mode: bgp : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# bgp fabric(config-pod-bgp)# route-reflector spine <LIST> [description <TEXT>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)634
R Commandsroute-reflector
router-idrouter-id <A.B.C.D|A:B::C:D>
Description: Set router-id for peer l4l7 device
Syntax:
IP address for the l4l7 peerA.B.C.D|A:B::C:D
Command Mode: rtr-cfg : Configure l4l7 router configuration parameters
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# rtr-cfg <WORD>(rtr-cfg)# router-id <A.B.C.D|A:B::C:D>
router-id <A.B.C.D>
Description: Configure Router ID
Syntax:
Router ID ValueA.B.C.D
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# router-id <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 635
R Commandsrouter-id
router bgprouter bgp <fabric-ASN>
Description: Border Gateway Protocol (BGP)
Syntax:
Autonomous System Number<fabric-ASN>
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)636
R Commandsrouter bgp
router eigrprouter eigrp default
Description: Enhanced Interior Gateway Routing Protocol (EIGRP)
Syntax:
EIGRP process tagdefault
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 637
R Commandsrouter eigrp
router ospfrouter ospf default
Description: Open Shortest Path First (OSPF and OSPF Version3)
Syntax:
Process tag for ospf and ospfv3default
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)638
R Commandsrouter ospf
rtr-cfgrtr-cfg <WORD>
Description: Configure router configuration association for a l4l7 service.
Syntax:
router configuration name (Max Size 64)WORD
Command Mode: service : Configure L4-L7 Service
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>](config-service)# rtr-cfg <WORD>
rtr-cfg <WORD>
Description: Configure l4l7 router configuration parameters
Syntax:
router configuration name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# rtr-cfg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 639
R Commandsrtr-cfg
run-moderun-mode pause-never|pause-on-failure
Description: Set run-mode
Syntax:
Do not pause on failurepause-never
Pause upgrade if upgrade of current set of nodes failpause-on-failure
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# run-mode pause-never|pause-on-failure
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)640
R Commandsrun-mode
S Commands
• schedule, page 661
• scheduler, page 662
• scheduling, page 663
• scope, page 664
• scvmm, page 665
• second-file, page 666
• security-domain, page 667
• security, page 668
• send-community, page 669
• server, page 670
• service-policy, page 673
• service, page 676
• session-record-flags, page 677
• set, page 678
• set burst, page 680
• set cir, page 681
• set community, page 682
• set conform-cos-transmit, page 685
• set conform-dscp-transmit, page 686
• set conform, page 687
• set dampening, page 688
• set dscp, page 689
• set exceed-cos-transmit, page 690
• set exceed-dscp-transmit, page 691
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 641
• set exceed, page 692
• set excessive-burst, page 693
• set local-preference, page 694
• set metric-type, page 696
• set metric, page 698
• set mode, page 700
• set pir, page 701
• set qos-class, page 702
• set tag, page 703
• set target-dscp, page 705
• set type, page 706
• set violate-cos-transmit, page 707
• set violate-dscp-transmit, page 708
• set violate, page 709
• set weight, page 710
• shellinabox, page 712
• show aaa authentication, page 713
• show aaa groups, page 714
• show access-list, page 715
• show accounting log, page 716
• show application, page 717
• show audits, page 718
• show audits tenant, page 719
• show audits tenant application, page 720
• show audits tenant application epg, page 721
• show audits tenant bridge-domain, page 722
• show audits tenant bridge-domain detail, page 723
• show audits tenant interface bridge-domain, page 724
• show audits tenant interface bridge-domain detail, page 725
• show audits tenant vrf, page 726
• show audits tenant vrf detail, page 727
• show audits tenant vrf external-l3 bgp, page 728
• show audits tenant vrf external-l3 bgp node, page 729
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)642
S Commands
• show audits tenant vrf external-l3 eigrp, page 730
• show audits tenant vrf external-l3 eigrp detail, page 731
• show audits tenant vrf external-l3 epg, page 732
• show audits tenant vrf external-l3 epg detail, page 733
• show audits tenant vrf external-l3 epg name, page 734
• show audits tenant vrf external-l3 epg name detail, page 735
• show audits tenant vrf external-l3 interfaces, page 736
• show audits tenant vrf external-l3 interfaces detail, page 737
• show audits tenant vrf external-l3 ospf, page 738
• show audits tenant vrf external-l3 ospf detail, page 739
• show audits tenant vrf external-l3 static-route, page 740
• show audits tenant vrf external-l3 static-route detail, page 741
• show audits tenant vrf external-l3 static-route node, page 742
• show audits tenant vrf external-l3 static-route node detail, page 743
• show bridge-domain, page 744
• show bridge-domain detail, page 745
• show callhome, page 746
• show callhome common destination-profile, page 747
• show callhome common query-profile, page 748
• show callhome common transport-email, page 749
• show catalog, page 750
• show cli command, page 751
• show cli internal audit, page 752
• show cli internal transaction, page 753
• show cli list, page 754
• show cli manpage, page 755
• show cli path, page 756
• show clock, page 757
• show communication ciphers, page 758
• show communication http, page 759
• show communication https, page 760
• show communication shellinabox, page 761
• show communication ssh-service, page 762
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 643
S Commands
• show communication telnet, page 763
• show communication web-requests, page 764
• show contract-type, page 765
• show contract, page 766
• show controller, page 767
• show controller detail, page 768
• show cores, page 769
• show debug counter, page 770
• show debug log, page 771
• show dns-address, page 772
• show dns-domain, page 773
• show endpoints, page 774
• show endpoints leaf interface ethernet, page 775
• show endpoints leaf interface port-channel, page 776
• show endpoints vpc, page 777
• show epg, page 778
• show epg detail, page 779
• show events, page 780
• show events controller, page 781
• show events controller detail, page 782
• show events leaf, page 783
• show events leaf fex, page 784
• show events leaf fex module, page 785
• show events leaf interface ethernet, page 786
• show events leaf interface l3instance, page 787
• show events leaf interface mgmt, page 788
• show events leaf interface portchannel, page 789
• show events leaf interface tunnel, page 790
• show events leaf inventory chassis, page 791
• show events leaf inventory fans, page 792
• show events leaf inventory module, page 793
• show events leaf inventory module fabricport, page 794
• show events leaf inventory module leafport, page 795
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)644
S Commands
• show events leaf inventory powersupply, page 796
• show events leaf inventory supervisor, page 797
• show events leaf protocol, page 798
• show events leaf vpc, page 799
• show events leaf vrf, page 800
• show events spine, page 801
• show events spine interface ethernet, page 802
• show events spine interface l3instance, page 803
• show events spine interface mgmt, page 804
• show events spine interface tunnel, page 805
• show events spine inventory chassis, page 806
• show events spine inventory fabric, page 807
• show events spine inventory fans, page 808
• show events spine inventory module, page 809
• show events spine inventory module fabricport, page 810
• show events spine inventory powersupply, page 811
• show events spine inventory supervisor, page 812
• show events spine inventory system, page 813
• show events spine protocol, page 814
• show events spine vrf, page 815
• show events tenant, page 816
• show events tenant application, page 817
• show events tenant application epg, page 818
• show events tenant bridge-domain, page 819
• show events tenant bridge-domain detail, page 820
• show events tenant endpoints, page 821
• show events tenant endpoints leaf interface ethernet, page 822
• show events tenant endpoints leaf interface port-channel, page 823
• show events tenant endpoints vpc, page 824
• show events tenant interface bridge-domain, page 826
• show events tenant interface bridge-domain detail, page 827
• show events tenant vrf, page 828
• show events tenant vrf detail, page 829
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 645
S Commands
• show events tenant vrf external-l3 bgp, page 830
• show events tenant vrf external-l3 bgp node, page 831
• show events tenant vrf external-l3 eigrp, page 832
• show events tenant vrf external-l3 eigrp detail, page 833
• show events tenant vrf external-l3 epg, page 834
• show events tenant vrf external-l3 epg detail, page 835
• show events tenant vrf external-l3 epg name, page 836
• show events tenant vrf external-l3 epg name detail, page 837
• show events tenant vrf external-l3 interfaces, page 838
• show events tenant vrf external-l3 interfaces detail, page 839
• show events tenant vrf external-l3 ospf, page 840
• show events tenant vrf external-l3 ospf detail, page 841
• show events tenant vrf external-l3 route-map, page 842
• show events tenant vrf external-l3 route-map detail, page 843
• show events tenant vrf external-l3 static-route, page 844
• show events tenant vrf external-l3 static-route detail, page 845
• show events tenant vrf external-l3 static-route node, page 846
• show events tenant vrf external-l3 static-route node detail, page 847
• show external-l2 epg, page 848
• show external-l2 epg name, page 849
• show external-l2 epg tenant, page 850
• show external-l3 bgp, page 851
• show external-l3 bgp tenant, page 852
• show external-l3 bgp tenant vrf, page 853
• show external-l3 bgp tenant vrf node, page 854
• show external-l3 eigrp, page 855
• show external-l3 eigrp detail, page 856
• show external-l3 eigrp node, page 857
• show external-l3 eigrp node detail, page 858
• show external-l3 eigrp tenant, page 859
• show external-l3 eigrp tenant detail, page 860
• show external-l3 eigrp tenant vrf, page 861
• show external-l3 eigrp tenant vrf detail, page 862
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)646
S Commands
• show external-l3 eigrp tenant vrf node, page 863
• show external-l3 eigrp tenant vrf node detail, page 864
• show external-l3 epg, page 865
• show external-l3 epg detail, page 866
• show external-l3 epg name, page 867
• show external-l3 epg name detail, page 868
• show external-l3 epg tenant, page 869
• show external-l3 epg tenant detail, page 870
• show external-l3 epg tenant vrf, page 871
• show external-l3 epg tenant vrf detail, page 872
• show external-l3 interfaces, page 873
• show external-l3 interfaces detail, page 874
• show external-l3 interfaces node, page 875
• show external-l3 interfaces node detail, page 876
• show external-l3 interfaces tenant, page 877
• show external-l3 interfaces tenant detail, page 878
• show external-l3 interfaces tenant vrf, page 879
• show external-l3 interfaces tenant vrf detail, page 880
• show external-l3 interfaces tenant vrf node, page 881
• show external-l3 interfaces tenant vrf node detail, page 882
• show external-l3 ospf, page 883
• show external-l3 ospf detail, page 884
• show external-l3 ospf node, page 885
• show external-l3 ospf node detail, page 886
• show external-l3 ospf tenant, page 887
• show external-l3 ospf tenant detail, page 888
• show external-l3 ospf tenant vrf, page 889
• show external-l3 ospf tenant vrf detail, page 890
• show external-l3 ospf tenant vrf node, page 891
• show external-l3 ospf tenant vrf node detail, page 892
• show external-l3 route-map, page 893
• show external-l3 route-map detail, page 894
• show external-l3 route-map name, page 895
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 647
S Commands
• show external-l3 route-map name detail, page 896
• show external-l3 route-map tenant, page 897
• show external-l3 route-map tenant detail, page 898
• show external-l3 route-map tenant vrf, page 899
• show external-l3 route-map tenant vrf detail, page 900
• show external-l3 route-map tenant vrf node, page 901
• show external-l3 route-map tenant vrf node detail, page 902
• show external-l3 static-route, page 903
• show external-l3 static-route detail, page 904
• show external-l3 static-route node, page 905
• show external-l3 static-route node detail, page 906
• show external-l3 static-route tenant, page 907
• show external-l3 static-route tenant detail, page 908
• show external-l3 static-route tenant vrf, page 909
• show external-l3 static-route tenant vrf detail, page 910
• show external-l3 static-route tenant vrf node, page 911
• show external-l3 static-route tenant vrf node detail, page 912
• show fabric-recovery status, page 913
• show faults, page 914
• show faults controller, page 916
• show faults controller detail, page 917
• show faults l4l7-cluster, page 918
• show faults l4l7-graph, page 919
• show faults leaf, page 920
• show faults leaf fex, page 921
• show faults leaf fex module, page 922
• show faults leaf interface ethernet, page 923
• show faults leaf interface l3instance, page 924
• show faults leaf interface mgmt, page 925
• show faults leaf interface portchannel, page 926
• show faults leaf interface tunnel, page 927
• show faults leaf inventory chassis, page 928
• show faults leaf inventory fans, page 929
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)648
S Commands
• show faults leaf inventory module, page 930
• show faults leaf inventory module fabricport, page 931
• show faults leaf inventory module leafport, page 932
• show faults leaf inventory powersupply, page 933
• show faults leaf inventory supervisor, page 934
• show faults leaf protocol, page 935
• show faults leaf vpc, page 936
• show faults leaf vrf, page 937
• show faults microsoft domain, page 938
• show faults microsoft domain name, page 939
• show faults microsoft domain name hyperv, page 940
• show faults microsoft domain name port-group, page 941
• show faults microsoft domain name scvmm, page 942
• show faults microsoft domain name vm, page 943
• show faults microsoft domain name vm name, page 944
• show faults spine, page 945
• show faults spine interface ethernet, page 946
• show faults spine interface l3instance, page 947
• show faults spine interface mgmt, page 948
• show faults spine interface tunnel, page 949
• show faults spine inventory chassis, page 950
• show faults spine inventory fabric, page 951
• show faults spine inventory fans, page 952
• show faults spine inventory module, page 953
• show faults spine inventory module fabricport, page 954
• show faults spine inventory powersupply, page 955
• show faults spine inventory supervisor, page 956
• show faults spine inventory system, page 957
• show faults spine protocol, page 958
• show faults spine vrf, page 959
• show faults tenant, page 960
• show faults tenant application, page 961
• show faults tenant application epg, page 962
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 649
S Commands
• show faults tenant bridge-domain, page 963
• show faults tenant bridge-domain detail, page 964
• show faults tenant interface bridge-domain, page 965
• show faults tenant interface bridge-domain detail, page 966
• show faults tenant vrf, page 967
• show faults tenant vrf detail, page 968
• show faults tenant vrf external-l3 bgp, page 969
• show faults tenant vrf external-l3 bgp node, page 970
• show faults tenant vrf external-l3 eigrp, page 971
• show faults tenant vrf external-l3 eigrp detail, page 972
• show faults tenant vrf external-l3 epg, page 973
• show faults tenant vrf external-l3 epg detail, page 974
• show faults tenant vrf external-l3 epg name, page 975
• show faults tenant vrf external-l3 epg name detail, page 976
• show faults tenant vrf external-l3 interfaces, page 977
• show faults tenant vrf external-l3 interfaces detail, page 978
• show faults tenant vrf external-l3 ospf, page 979
• show faults tenant vrf external-l3 ospf detail, page 980
• show faults tenant vrf external-l3 static-route, page 981
• show faults tenant vrf external-l3 static-route detail, page 982
• show faults tenant vrf external-l3 static-route node, page 983
• show faults tenant vrf external-l3 static-route node detail, page 984
• show faults vmware domain, page 985
• show faults vmware domain name, page 986
• show faults vmware domain name epg, page 987
• show faults vmware domain name esx, page 988
• show faults vmware domain name port-group, page 989
• show faults vmware domain name vcenter, page 990
• show faults vmware domain name vm, page 991
• show faults vmware domain name vm name, page 992
• show firmware repository, page 993
• show firmware repository detail, page 994
• show firmware upgrade status, page 995
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)650
S Commands
• show firmware upgrade status controller-group, page 996
• show firmware upgrade status controller-group detail, page 997
• show firmware upgrade status detail, page 998
• show firmware upgrade status switch-group, page 999
• show firmware upgrade status switch-group detail, page 1000
• show health, page 1001
• show health l4l7-cluster, page 1002
• show health l4l7-graph, page 1003
• show health leaf, page 1004
• show health leaf fex, page 1005
• show health leaf fex module, page 1006
• show health leaf interface ethernet, page 1007
• show health leaf interface l3instance, page 1008
• show health leaf interface mgmt, page 1009
• show health leaf interface portchannel, page 1010
• show health leaf interface tunnel, page 1011
• show health leaf inventory chassis, page 1012
• show health leaf inventory fans, page 1013
• show health leaf inventory module, page 1014
• show health leaf inventory module fabricport, page 1015
• show health leaf inventory module leafport, page 1016
• show health leaf inventory powersupply, page 1017
• show health leaf inventory supervisor, page 1018
• show health leaf protocol, page 1019
• show health leaf vpc, page 1020
• show health leaf vrf, page 1021
• show health spine, page 1022
• show health spine interface ethernet, page 1023
• show health spine interface l3instance, page 1024
• show health spine interface mgmt, page 1025
• show health spine interface tunnel, page 1026
• show health spine inventory chassis, page 1027
• show health spine inventory fabric, page 1028
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 651
S Commands
• show health spine inventory fans, page 1029
• show health spine inventory module, page 1030
• show health spine inventory module fabricport, page 1031
• show health spine inventory powersupply, page 1032
• show health spine inventory supervisor, page 1033
• show health spine inventory system, page 1034
• show health spine protocol, page 1035
• show health spine vrf, page 1036
• show health tenant, page 1037
• show health tenant application, page 1038
• show health tenant application epg, page 1039
• show health tenant bridge-domain, page 1040
• show health tenant bridge-domain detail, page 1041
• show health tenant interface bridge-domain, page 1042
• show health tenant interface bridge-domain detail, page 1043
• show health tenant vrf, page 1044
• show health tenant vrf detail, page 1045
• show health tenant vrf external-l3 bgp, page 1046
• show health tenant vrf external-l3 bgp node, page 1047
• show health tenant vrf external-l3 eigrp, page 1048
• show health tenant vrf external-l3 eigrp detail, page 1049
• show health tenant vrf external-l3 epg, page 1050
• show health tenant vrf external-l3 epg detail, page 1051
• show health tenant vrf external-l3 epg name, page 1052
• show health tenant vrf external-l3 epg name detail, page 1053
• show health tenant vrf external-l3 interfaces, page 1054
• show health tenant vrf external-l3 interfaces detail, page 1055
• show health tenant vrf external-l3 ospf, page 1056
• show health tenant vrf external-l3 ospf detail, page 1057
• show health tenant vrf external-l3 static-route, page 1058
• show health tenant vrf external-l3 static-route detail, page 1059
• show health tenant vrf external-l3 static-route node, page 1060
• show health tenant vrf external-l3 static-route node detail, page 1061
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)652
S Commands
• show inband-mgmt, page 1062
• show inband-mgmt controller, page 1063
• show inband-mgmt switch, page 1064
• show interface bridge-domain, page 1065
• show interface bridge-domain detail, page 1066
• show ip interface bridge-domain, page 1067
• show ipv6 interface bridge-domain, page 1068
• show l4l7-cluster, page 1069
• show l4l7-graph, page 1070
• show l4l7-package, page 1071
• show ldap-server, page 1072
• show locator-led, page 1073
• show locator-led status leaf, page 1074
• show microsoft domain, page 1075
• show microsoft domain name, page 1076
• show microsoft domain name hyperv, page 1077
• show microsoft domain name port-group, page 1078
• show microsoft domain name scvmm, page 1079
• show microsoft domain name vm, page 1080
• show microsoft domain name vm name, page 1081
• show microsoft vm, page 1082
• show monitor access, page 1083
• show monitor fabric, page 1084
• show monitor tenant, page 1085
• show monitor virtual, page 1086
• show ntpq, page 1087
• show oob-mgmt, page 1088
• show oob-mgmt controller, page 1089
• show oob-mgmt switch, page 1090
• show policy-map, page 1091
• show policy-map type data-plane, page 1092
• show policy-map type qos, page 1093
• show port-channel leaf, page 1094
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 653
S Commands
• show port-channel map, page 1095
• show port-channel map leaf, page 1096
• show radius-server, page 1097
• show resource, page 1098
• show resource conflict encap-vlan epg, page 1099
• show resource conflict encap-vlan epg node, page 1100
• show role, page 1101
• show running-config, page 1102
• show sessions, page 1103
• show sessions controller, page 1104
• show sessions controller detail, page 1105
• show sessions leaf, page 1106
• show sessions spine, page 1107
• show snapshot active, page 1108
• show snapshot files, page 1109
• show snapshot jobs, page 1110
• show snmp, page 1111
• show snmp clientgroups, page 1112
• show snmp community, page 1113
• show snmp engineid, page 1114
• show snmp hosts, page 1115
• show snmp users, page 1116
• show stats, page 1117
• show stats granularity leaf, page 1118
• show stats granularity leaf fex, page 1119
• show stats granularity leaf fex module, page 1120
• show stats granularity leaf interface ethernet, page 1121
• show stats granularity leaf interface mgmt, page 1122
• show stats granularity leaf interface portchannel, page 1123
• show stats granularity leaf inventory fans, page 1124
• show stats granularity leaf inventory powersupply, page 1125
• show stats granularity leaf inventory supervisor, page 1126
• show stats granularity spine, page 1127
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)654
S Commands
• show stats granularity spine interface ethernet, page 1128
• show stats granularity spine interface mgmt, page 1129
• show stats granularity spine inventory chassis, page 1130
• show stats granularity spine inventory fabric, page 1131
• show stats granularity spine inventory fans, page 1132
• show stats granularity spine inventory module, page 1133
• show stats granularity spine inventory powersupply, page 1134
• show stats granularity spine inventory supervisor, page 1135
• show stats granularity spine inventory system, page 1136
• show stats granularity tenant, page 1137
• show stats granularity tenant application, page 1138
• show stats granularity tenant application epg, page 1139
• show switch, page 1140
• show switch detail, page 1141
• show tacacs-server, page 1142
• show techsupport all, page 1143
• show techsupport controllers, page 1144
• show techsupport host, page 1145
• show techsupport switch, page 1146
• show tenant, page 1147
• show tenant access-list, page 1148
• show tenant application, page 1149
• show tenant application endpoints, page 1150
• show tenant application endpoints leaf interface ethernet, page 1151
• show tenant application endpoints leaf interface port-channel, page 1152
• show tenant application endpoints vpc, page 1153
• show tenant application epg, page 1154
• show tenant application epg detail, page 1155
• show tenant application epg endpoints, page 1156
• show tenant application epg endpoints leaf interface ethernet, page 1157
• show tenant application epg endpoints leaf interface port-channel, page 1158
• show tenant application epg endpoints vpc, page 1159
• show tenant bridge-domain, page 1161
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 655
S Commands
• show tenant bridge-domain detail, page 1162
• show tenant contract-type, page 1163
• show tenant contract, page 1164
• show tenant detail, page 1165
• show tenant endpoints, page 1166
• show tenant endpoints leaf interface ethernet, page 1167
• show tenant endpoints leaf interface port-channel, page 1168
• show tenant endpoints vpc, page 1169
• show tenant epg, page 1170
• show tenant epg detail, page 1171
• show tenant external-l2 epg, page 1172
• show tenant interface bridge-domain, page 1173
• show tenant interface bridge-domain detail, page 1174
• show tenant ip interface bridge-domain, page 1175
• show tenant ipv6 interface bridge-domain, page 1176
• show tenant policy-map, page 1177
• show tenant policy-map type data-plane, page 1178
• show tenant policy-map type qos, page 1179
• show tenant vrf, page 1180
• show tenant vrf detail, page 1181
• show tenant vrf external-l3 bgp, page 1182
• show tenant vrf external-l3 bgp node, page 1183
• show tenant vrf external-l3 eigrp, page 1184
• show tenant vrf external-l3 eigrp detail, page 1185
• show tenant vrf external-l3 epg, page 1186
• show tenant vrf external-l3 epg detail, page 1187
• show tenant vrf external-l3 epg name, page 1188
• show tenant vrf external-l3 epg name detail, page 1189
• show tenant vrf external-l3 interfaces, page 1190
• show tenant vrf external-l3 interfaces detail, page 1191
• show tenant vrf external-l3 ospf, page 1192
• show tenant vrf external-l3 ospf detail, page 1193
• show tenant vrf external-l3 route-map, page 1194
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)656
S Commands
• show tenant vrf external-l3 route-map detail, page 1195
• show tenant vrf external-l3 static-route, page 1196
• show tenant vrf external-l3 static-route detail, page 1197
• show tenant vrf external-l3 static-route node, page 1198
• show tenant vrf external-l3 static-route node detail, page 1199
• show troubleshoot epext session, page 1200
• show troubleshoot epext session atomiccounter, page 1201
• show troubleshoot epext session audit, page 1202
• show troubleshoot epext session contracts, page 1203
• show troubleshoot epext session deployments, page 1204
• show troubleshoot epext session events, page 1205
• show troubleshoot epext session faults, page 1206
• show troubleshoot epext session monitor, page 1207
• show troubleshoot epext session reports, page 1208
• show troubleshoot epext session statistics, page 1209
• show troubleshoot epext session topology, page 1210
• show troubleshoot epext session traceroute, page 1211
• show troubleshoot epext sessions, page 1212
• show troubleshoot eptoep session, page 1213
• show troubleshoot eptoep session atomiccounter, page 1214
• show troubleshoot eptoep session audit, page 1215
• show troubleshoot eptoep session contracts, page 1216
• show troubleshoot eptoep session deployments, page 1217
• show troubleshoot eptoep session events, page 1218
• show troubleshoot eptoep session faults, page 1219
• show troubleshoot eptoep session monitor, page 1220
• show troubleshoot eptoep session reports, page 1221
• show troubleshoot eptoep session statistics, page 1222
• show troubleshoot eptoep session topology, page 1223
• show troubleshoot eptoep session traceroute, page 1224
• show troubleshoot eptoep sessions, page 1225
• show username, page 1226
• show username detail, page 1227
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 657
S Commands
• show version, page 1228
• show vlan-domain, page 1229
• show vmware domain, page 1230
• show vmware domain name, page 1231
• show vmware domain name epg, page 1232
• show vmware domain name esx, page 1233
• show vmware domain name port-group, page 1234
• show vmware domain name vcenter, page 1235
• show vmware domain name vm, page 1236
• show vmware domain name vm name, page 1237
• show vmware vm, page 1238
• show vpc, page 1239
• show vpc map leaf, page 1240
• show vrf, page 1241
• show vrf detail, page 1242
• shut, page 1243
• shutdown, page 1244
• site-id, page 1246
• slow-timer, page 1247
• snapshot download, page 1248
• snapshot export, page 1249
• snapshot import, page 1250
• snapshot rollback, page 1251
• snapshot upload, page 1252
• snmp-server clientgroup, page 1253
• snmp-server community, page 1254
• snmp-server contact, page 1255
• snmp-server host, page 1256
• snmp-server location, page 1257
• snmp-server protocol, page 1258
• snmp-server user, page 1259
• source, page 1260
• source application, page 1261
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)658
S Commands
• source interface ethernet, page 1262
• source interface port-channel, page 1263
• source interface vpc, page 1264
• spanning-tree, page 1265
• spanning-tree bpdu-filter, page 1268
• spanning-tree bpdu-guard, page 1269
• speed, page 1270
• spf-interval, page 1272
• ssh-key, page 1273
• ssh-service, page 1274
• ssl-protocols, page 1275
• ssl-validation-level, page 1276
• state, page 1277
• static-endpoint, page 1278
• static-tep, page 1281
• statistics, page 1283
• storm-control level, page 1284
• storm-control pps, page 1286
• street-address, page 1289
• subject, page 1290
• summary-address, page 1291
• switch-group, page 1292
• switch, page 1293
• switching, page 1294
• switchport, page 1295
• switchport access vlan tenant application, page 1297
• switchport access vlan tenant external-svi, page 1299
• switchport trunk allowed vlan inband-mgmt, page 1301
• switchport trunk allowed vlan tenant application, page 1302
• switchport trunk allowed vlan tenant external-l2, page 1304
• switchport trunk allowed vlan tenant external-svi, page 1306
• switchport trunk allowed vlan tenant legacy-forwarding, page 1308
• switchport trunk native vlan tenant application, page 1310
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 659
S Commands
• switchport trunk native vlan tenant external-svi, page 1312
• switchport vlan, page 1314
• syslog, page 1316
• system cluster-size, page 1317
• system controller-id, page 1318
• system dynamic-load-balance, page 1319
• system fabric-security-mode, page 1320
• system jumbomtu, page 1321
• system switch-id, page 1322
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)660
S Commands
scheduleschedule <WORD>
Description: Assign a scheduler
Syntax:
scheduler name (Max Size 64)WORD
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# schedule <WORD>
schedule <WORD>
Description: Schedule snapshot export
Syntax:
Scheduler nameWORD
Command Mode: snapshot export : Configuration export setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# schedule <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 661
S Commandsschedule
schedulerscheduler pause
Description: Pause maintenance policy scheduler
Syntax:
Pause maintenance policy schedulerpause
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# scheduler pause
scheduler fabric|controller schedule <WORD>
Description: Scheduler configuration mode
Syntax:
Fabric schedulesfabric
Controller schedulescontroller
Configure a scheduleschedule
Schedule name (Max size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)662
S Commandsscheduler
schedulingscheduling <WORD>
Description: Set the scheduling algorithm
Syntax:
Algorithm to chooseWORD
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# scheduling <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 663
S Commandsscheduling
scopescope <WORD>
Description: Specify the scope for the contract
Syntax:
Contract ScopeWORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# scope <WORD>
scope global
Description: Set scope
Syntax:
Route-map will be available for use on all nodes in this tenant and vrfglobal
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# scope global
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)664
S Commandsscope
scvmmscvmm <arg> cloud <WORD> [name <name>]
Description: Configure an SCVMM in the Microsoft domain
Syntax:
arg
Cloud namecloud
Cloud Name (Max Size 512)WORD
(Optional) SCVMM Controller Namename
Command Mode: microsoft-domain : Create a VMMMicrosoft Domain
Command Path:
# configure [['terminal', 't']](config)# microsoft-domain <WORD>(config-microsoft)# scvmm <> cloud <WORD> [name <name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 665
S Commandsscvmm
second-filesecond-file <FILENAME>
Description: Second snapshot file name
Syntax:
Second snapshot file nameFILENAME
Command Mode: snapshot rollback : Configuration rollback setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>(config-rollback)# second-file <FILENAME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)666
S Commandssecond-file
security-domainsecurity-domain <WORD>
Description: Add security domain
Syntax:
Security-domain nameWORD
Command Mode: vlan-domain : Configure vlan domain
Command Path:
# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# security-domain <WORD>
security-domain <WORD>
Description: Add a security domain to this VMware domain
Syntax:
Security domain name (Max Size 64)WORD
Command Mode: vmware-domain : Create a VMM VMware Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# security-domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 667
S Commandssecurity-domain
securitysecurity domain <WORD>
Description: Add a security domain to the tenant
Syntax:
Domaindomain
Security domain name (Max Size None)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# security domain <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)668
S Commandssecurity
send-communitysend-community [extended]
Description: Send Community attribute to this neighbor
Syntax:
(Optional) Send Extended Community attributeextended
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# send-community [extended]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 669
S Commandssend-community
serverserver <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add LDAP server to LDAP group
Syntax:
LDAP server name or IP addressA.B.C.D|A:B::C:D|WORD
priority of server within grouppriority
Priority of server within group. Number range from=0 to=16<0-16>
Command Mode: aaa group server ldap : LDAP server group name.
Command Path:
# configure [['terminal', 't']](config)# aaa group server ldap <WORD>(config-ldap)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add RADIUS server to RADIUS group
Syntax:
RADIUS server name or IP addressA.B.C.D|A:B::C:D|WORD
priority of server within grouppriority
Priority of server within group. Number range from=0 to=16<0-16>
Command Mode: aaa group server radius : RADIUS server group name.
Command Path:
# configure [['terminal', 't']](config)# aaa group server radius <WORD>(config-radius)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
Description: Add TACACS PLUS server to TACACS PLUS group
Syntax:
TACACS PLUS server name or IP addressA.B.C.D|A:B::C:D|WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)670
S Commandsserver
priority of server within grouppriority
Priority of server within group. Number range from=0 to=16<0-16>
Command Mode: aaa group server tacacsplus : TACACS+ server group name.
Command Path:
# configure [['terminal', 't']](config)# aaa group server tacacsplus <WORD>(config-tacacsplus)# server <A.B.C.D|A:B::C:D|WORD> priority <NUMBER>
server <WORD> [prefer] [key <arg>] [use-vrf <arg>]
Description: Configure ntp servers for the active ntp policy
Syntax:
Server name/IP for the active ntp policy (Max Size 64)WORD
(Optional) Preferred server for the active ntp policyprefer
(Optional) Reference key id for authentication. Number range from=1to=65535
arg
(Optional) Configure management vrfarg
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# server <WORD> [prefer] [key <>] [use-vrf <>]
server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg <mgmtepg>] [port <port>]
Description: Add a destination server
Syntax:
The hostname or ipaddress<host/ipaddr>
(Optional) The forwarding facility level for logs generatedfacility
(Optional) The severity level for logs generatedseverity
(Optional) MgmtEndpointmgmtepg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 671
S Commandsserver
(Optional) Service port of the remote destination. Number range from=1to=65535
port
Command Mode: logging : Logging server group configuration mode
Command Path:
# configure [['terminal', 't']](config)# logging server-group <WORD>(config-logging)# server <host/ipaddr> [facility <facility>] [severity <severity>] [mgmtepg<mgmtepg>] [port <port>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)672
S Commandsserver
service-policyservice-policy <WORD>
Description: Specify the QOS service policy
Syntax:
Qos Service Policy (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# service-policy <WORD>
service-policy <WORD>
Description: Specify the QOS service policy
Syntax:
Service policy to apply (Max Size 64)WORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# service-policy <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 673
S Commandsservice-policy
Qos Policy Name (Max Size 64)WORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# service-policy type data-plane input|output <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Qos Policy Name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# service-policy type data-plane input|output <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Qos Policy Name (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)674
S Commandsservice-policy
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# service-policy type data-plane input|output <WORD>
service-policy type data-plane input|output <WORD>
Description: QOS service policy
Syntax:
Type of the Qos Policytype
QOS policy for Data Plane Policingdata-plane
Ingress Directioninput
Egress Directionoutput
Qos Policy Name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# service-policy type data-plane input|output <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 675
S Commandsservice-policy
serviceservice <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode <Available Modes>]
Description: Configure L4-L7 Service
Syntax:
Service node name (Max Size 64)WORD
(Optional) Tenant name (Max Size 63)WORD
(Optional) Device cluster name (Max Size 64)WORD
(Optional) DescriptionAvailable Modes
Command Mode: l4l7 graph : Configure L4-L7 Service Graph
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 graph <WORD> [contract <contract-option>](config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode<Available Modes>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)676
S Commandsservice
session-record-flagssession-record-flags <sessionRecordFlags>
Description: Enable/Disable refresh in the session records, Comma separated values
Syntax:
Session record flags as comma separated values like val1,val2,..valN<sessionRecordFlags>
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# session-record-flags <sessionRecordFlags>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 677
S Commandssession-record-flags
setset qos-class <WORD>
Description: QOS level for the epg
Syntax:
QOS level for the epgqos-class
Qos LevelWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# set qos-class <WORD>
set qos-class <WORD>
Description: QOS level for the application
Syntax:
QOS level for the applicationqos-class
Qos LevelWORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# set qos-class <WORD>
set qos-class <contractQosLevel>
Description: Specify the QOS level for the epg
Syntax:
class of QOS to specifyqos-class
{unspecified|level1|level2|level3}<contractQosLevel>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)678
S Commandsset
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# set qos-class <contractQosLevel>
set qos-class <WORD>
Description: QOS level for the epg
Syntax:
QOS level for the epgqos-class
Qos LevelWORD
Command Mode: external-l2 : L2 external EPG creation/configuration
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l2 epg <WORD>(config-tenant-l2ext-epg)# set qos-class <WORD>
set qos-class <contractQosLevel>
Description: QOS level for the epg
Syntax:
class of QOS to specifyqos-class
{unspecified|level1|level2|level3}<contractQosLevel>
Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# oob-mgmt epg <epgval>(config-oob-epg)# set qos-class <contractQosLevel>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 679
S Commandsset
set burstset burst <0-4294967295> UNIT
Description: Burst Rate
Syntax:
Burst Rate<0-4294967295>
Burst Rate UnitUNIT
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set burst <0-4294967295> UNIT
set burst <0-4294967295> UNIT
Description: Burst Rate
Syntax:
Burst Rate<0-4294967295>
Burst Rate UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set burst <0-4294967295> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)680
S Commandsset burst
set cirset cir <0-4294967295> UNIT
Description: Committed Rate
Syntax:
Committed Rate<0-4294967295>
Committed Rate UnitUNIT
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set cir <0-4294967295> UNIT
set cir <0-4294967295> UNIT
Description: Committed Rate
Syntax:
Committed Rate<0-4294967295>
Committed Rate UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set cir <0-4294967295> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 681
S Commandsset cir
set communityset community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)682
S Commandsset community
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 683
S Commandsset community
Replace existing communityreplace
Do not change communitynone
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set community regular|extended <value>additive|replace|none
set community regular|extended <value> additive|replace|none
Description: Set BGP community attribute
Syntax:
BGP regular communityregular
BGP extended communityextended
Community value in aa:nn formatvalue
Add to existing communityadditive
Replace existing communityreplace
Do not change communitynone
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set community regular|extended <value>additive|replace|none
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)684
S Commandsset community
set conform-cos-transmitset conform-cos-transmit <0-6>
Description: Conform Policer Mark Cos
Syntax:
Conform Policer Mark Cos<0-6>
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform-cos-transmit <0-6>
set conform-cos-transmit <0-6>
Description: Conform Policer Mark Cos
Syntax:
Conform Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform-cos-transmit <0-6>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 685
S Commandsset conform-cos-transmit
set conform-dscp-transmitset conform-dscp-transmit <0-63>
Description: Conform Policer Mark DSCP
Syntax:
Conform Policer Mark DSCP<0-63>
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform-dscp-transmit <0-63>
set conform-dscp-transmit <0-63>
Description: Conform Policer Mark DSCP
Syntax:
Conform Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform-dscp-transmit <0-63>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)686
S Commandsset conform-dscp-transmit
set conformset conform <WORD>
Description: Conform Policer Action
Syntax:
Conform Policer ActionWORD
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set conform <WORD>
set conform <WORD>
Description: Conform Policer Action
Syntax:
Conform Policer ActionWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set conform <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 687
S Commandsset conform
set dampeningset dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Description: Route Flap dampening
Syntax:
Decay half life. Number range from=1 to=60<1-60>
Value to start reusing a route. Number range from=1 to=20000<1-20000>
Value to start suppressing a route. Number range from=1 to=20000<1-20000>
Maximum suppress time for stable route. Number range from=1 to=255<1-255>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set dampening <NUMBER> <NUMBER> <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)688
S Commandsset dampening
set dscpset dscp <WORD>
Description: Specify the DSCP level for the EPG
Syntax:
DSCP valueWORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# set dscp <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 689
S Commandsset dscp
set exceed-cos-transmitset exceed-cos-transmit <0-6>
Description: Exceed Policer Mark Cos
Syntax:
Exceed Policer Mark Cos<0-6>
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed-cos-transmit <0-6>
set exceed-cos-transmit <0-6>
Description: Exceed Policer Mark Cos
Syntax:
Exceed Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed-cos-transmit <0-6>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)690
S Commandsset exceed-cos-transmit
set exceed-dscp-transmitset exceed-dscp-transmit <0-63>
Description: Exceed Policer Mark DSCP
Syntax:
Exceed Policer Mark DSCP<0-63>
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed-dscp-transmit <0-63>
set exceed-dscp-transmit <0-63>
Description: Exceed Policer Mark DSCP
Syntax:
Exceed Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed-dscp-transmit <0-63>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 691
S Commandsset exceed-dscp-transmit
set exceedset exceed <WORD>
Description: Exceed Policer Action
Syntax:
Exceed Policer ActionWORD
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set exceed <WORD>
set exceed <WORD>
Description: Exceed Policer Action
Syntax:
Exceed Policer ActionWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set exceed <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)692
S Commandsset exceed
set excessive-burstset excessive-burst <0-4294967295> UNIT
Description: Excessive Burst Rate
Syntax:
Excessive Burst Rate<0-4294967295>
Excessive Burst Rate UnitUNIT
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set excessive-burst <0-4294967295> UNIT
set excessive-burst <0-4294967295> UNIT
Description: Excessive Burst Rate
Syntax:
Excessive Burst Rate<0-4294967295>
Excessive Burst Rate UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set excessive-burst <0-4294967295> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 693
S Commandsset excessive-burst
set local-preferenceset local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)694
S Commandsset local-preference
(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set local-preference <0-4294967295>
set local-preference <0-4294967295>
Description: BGP local preference path attribute
Syntax:
Preference value<0-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set local-preference <0-4294967295>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 695
S Commandsset local-preference
set metric-typeset metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)696
S Commandsset metric-type
(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set metric-type <metric-type>
set metric-type <metric-type>
Description: Type of metric for destination routing protocol
Syntax:
<metric-type><metric-type>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set metric-type <metric-type>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 697
S Commandsset metric-type
set metricset metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)698
S Commandsset metric
(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set metric <NUMBER>
set metric <NUMBER>
Description: Set metric for destination routing protocol
Syntax:
Metric value. Number range from=0 to=255<0-255>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set metric <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 699
S Commandsset metric
set modeset mode <WORD>
Description: Policer Mode
Syntax:
Policer ModeWORD
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set mode <WORD>
set mode <WORD>
Description: Policer Mode
Syntax:
Policer ModeWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set mode <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)700
S Commandsset mode
set pirset pir <0-4294967295> UNIT
Description: Peak Rate
Syntax:
Peak Rate<0-4294967295>
Pir UnitUNIT
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set pir <0-4294967295> UNIT
set pir <0-4294967295> UNIT
Description: Peak Rate
Syntax:
Peak Rate<0-4294967295>
Pir UnitUNIT
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set pir <0-4294967295> UNIT
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 701
S Commandsset pir
set qos-classset qos-class <WORD>
Description: Class of QOS to specify
Syntax:
Qos LevelWORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# set qos-class <WORD>
set qos-class unspecified|level1|level2|level3
Description: Specify the QOS level for the EPG
Syntax:
Unspecified QoS levelunspecified
QoS level1level1
QoS level2level2
QoS level3level3
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# set qos-class unspecified|level1|level2|level3
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)702
S Commandsset qos-class
set tagset tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 703
S Commandsset tag
(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set tag <NUMBER>
set tag <NUMBER>
Description: Tag value for destination routing protocol
Syntax:
Tag value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set tag <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)704
S Commandsset tag
set target-dscpset target-dscp <WORD>
Description: class of target dscp to specify
Syntax:
Target dscpWORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# set target-dscp <WORD>
set target-dscp <WORD> WORD
Description: class of target dscp to specify
Syntax:
Target dscpWORD
Target DSCP DirectionWORD
Command Mode: subject : Configuration a subject on the contract
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>(config-tenant-contract-subj)# set target-dscp <WORD> WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 705
S Commandsset target-dscp
set typeset type <WORD>
Description: Policer type
Syntax:
Policer TypeWORD
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set type <WORD>
set type <WORD>
Description: Policer type
Syntax:
Policer TypeWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set type <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)706
S Commandsset type
set violate-cos-transmitset violate-cos-transmit <0-6>
Description: Violate Policer Mark Cos
Syntax:
Violate Policer Mark Cos<0-6>
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate-cos-transmit <0-6>
set violate-cos-transmit <0-6>
Description: Violate Policer Mark Cos
Syntax:
Violate Policer Mark Cos<0-6>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate-cos-transmit <0-6>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 707
S Commandsset violate-cos-transmit
set violate-dscp-transmitset violate-dscp-transmit <0-63>
Description: Violate Policer Mark DSCP
Syntax:
Violate Policer Mark DSCP<0-63>
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate-dscp-transmit <0-63>
set violate-dscp-transmit <0-63>
Description: Violate Policer Mark DSCP
Syntax:
Violate Policer Mark DSCP<0-63>
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate-dscp-transmit <0-63>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)708
S Commandsset violate-dscp-transmit
set violateset violate <WORD>
Description: Violate Policer Action
Syntax:
Violate Policer ActionWORD
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# set violate <WORD>
set violate <WORD>
Description: Violate Policer Action
Syntax:
Violate Policer ActionWORD
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# set violate <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 709
S Commandsset violate
set weightset weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: route-profile : Configure route-profile
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>(config-tenant-vrf)# route-profile <WORD>(config-tenant-vrf-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
CommandMode: template route-profile : Configure route-profile template under tenant for BGP dampeningand route redistribution
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>(config-leaf-template-route-profile)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: match prefix-list : Match entries of a prefix-list
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)710
S Commandsset weight
(config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match prefix-list <WORD>(config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: match community : Configure community features
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# route-map <WORD>(config-leaf-vrf-route-map)# match community <WORD>(config-leaf-vrf-route-map-match)# set weight <NUMBER>
set weight <NUMBER>
Description:Weight value for destination routing protocol
Syntax:
Weight value. Number range from=0 to=65535<0-65535>
Command Mode: template route-profile : Configure route-profile template under VRF/L3Out forbridge-domain export
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>(config-leaf-vrf-template-route-profile)# set weight <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 711
S Commandsset weight
shellinaboxshellinabox
Description: Configures the communication policy of the SHELLINABOX feature
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Usage:
In the APIC GUI, the SHELLINABOX feature allows you to open a pop-up SSH session to a fabric switchby right-clicking the icon of the switch. To enable or disable this feature, use the shellinabox command toenter the SHELLINABOX communication policy group, then use the [no] admin-state-enable command.
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# shellinabox
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)712
S Commandsshellinabox
show aaa authenticationshow aaa authentication
Description: Show AAA Authentication information
Command Mode: exec : Exec Mode
Command Path:
# show aaa authentication
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 713
S Commandsshow aaa authentication
show aaa groupsshow aaa groups
Description: Show AAA group information
Command Mode: exec : Exec Mode
Command Path:
# show aaa groups
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)714
S Commandsshow aaa groups
show access-listshow access-list WORD
Description: Show Access-list Information
Syntax:
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show access-list WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 715
S Commandsshow access-list
show accounting logshow accounting log
Description: CLI configuration command logs
Command Mode: exec : Exec Mode
Command Path:
# show accounting log
NOTE:
This command displays only those changes made using the command line interface (CLI). It does not displaychanges made using the GUI or the API. To view all changes made in the Management Information Tree, usethe show audit detail command.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)716
S Commandsshow accounting log
show applicationshow application WORD
Description: Show Application Profiles Information
Syntax:
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 717
S Commandsshow application
show auditsshow audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show audit-log information
Syntax:
(Optional) Log ID<log-id>
(Optional) Object action indicatoraction<action-type>
(Optional) Name of user<user-name>
(Optional) Logs created in time interval. Number range from=1 to=59<num-minutes>
(Optional) Logs created in time interval. Number range from=1 to=23<num-hours>
(Optional) Logs created in time interval. Number range from=1 to=999<num-days>
(Optional) Logs created in time interval<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Logs created in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed audit-log information. Displays what was modifiedand displays the old and new settings.
detail
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)718
S Commandsshow audits
show audits tenantshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 719
S Commandsshow audits tenant
show audits tenant applicationshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)720
S Commandsshow audits tenant application
show audits tenant application epgshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 721
S Commandsshow audits tenant application epg
show audits tenant bridge-domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)722
S Commandsshow audits tenant bridge-domain
show audits tenant bridge-domain detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 723
S Commandsshow audits tenant bridge-domain detail
show audits tenant interface bridge-domainshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)724
S Commandsshow audits tenant interface bridge-domain
show audits tenant interface bridge-domain detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 725
S Commandsshow audits tenant interface bridge-domain detail
show audits tenant vrfshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)726
S Commandsshow audits tenant vrf
show audits tenant vrf detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 727
S Commandsshow audits tenant vrf detail
show audits tenant vrf external-l3 bgpshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)728
S Commandsshow audits tenant vrf external-l3 bgp
show audits tenant vrf external-l3 bgp nodeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 729
S Commandsshow audits tenant vrf external-l3 bgp node
show audits tenant vrf external-l3 eigrpshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)730
S Commandsshow audits tenant vrf external-l3 eigrp
show audits tenant vrf external-l3 eigrp detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 731
S Commandsshow audits tenant vrf external-l3 eigrp detail
show audits tenant vrf external-l3 epgshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)732
S Commandsshow audits tenant vrf external-l3 epg
show audits tenant vrf external-l3 epg detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 733
S Commandsshow audits tenant vrf external-l3 epg detail
show audits tenant vrf external-l3 epg nameshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)734
S Commandsshow audits tenant vrf external-l3 epg name
show audits tenant vrf external-l3 epg name detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 735
S Commandsshow audits tenant vrf external-l3 epg name detail
show audits tenant vrf external-l3 interfacesshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)736
S Commandsshow audits tenant vrf external-l3 interfaces
show audits tenant vrf external-l3 interfaces detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 737
S Commandsshow audits tenant vrf external-l3 interfaces detail
show audits tenant vrf external-l3 ospfshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)738
S Commandsshow audits tenant vrf external-l3 ospf
show audits tenant vrf external-l3 ospf detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 739
S Commandsshow audits tenant vrf external-l3 ospf detail
show audits tenant vrf external-l3 static-routeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)740
S Commandsshow audits tenant vrf external-l3 static-route
show audits tenant vrf external-l3 static-route detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 741
S Commandsshow audits tenant vrf external-l3 static-route detail
show audits tenant vrf external-l3 static-route nodeshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)742
S Commandsshow audits tenant vrf external-l3 static-route node
show audits tenant vrf external-l3 static-route node detailshow audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show audits [id <log-id>] [action <action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 743
S Commandsshow audits tenant vrf external-l3 static-route node detail
show bridge-domainshow bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)744
S Commandsshow bridge-domain
show bridge-domain detailshow bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 745
S Commandsshow bridge-domain detail
show callhomeshow callhome common
Description: Show command for callhome
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)746
S Commandsshow callhome
show callhome common destination-profileshow callhome common destination-profile
Description: Show command for callhome destination-profile
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common destination-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 747
S Commandsshow callhome common destination-profile
show callhome common query-profileshow callhome common query-profile
Description: Show command for callhome destination-profile
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common query-profile
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)748
S Commandsshow callhome common query-profile
show callhome common transport-emailshow callhome common transport-email
Description: Show command for callhome transport-email
Syntax:
Commoncommon
Command Mode: exec : Exec Mode
Command Path:
# show callhome common transport-email
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 749
S Commandsshow callhome common transport-email
show catalogshow catalog
Description: Show catalog information
Command Mode: exec : Exec Mode
Command Path:
# show catalog
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)750
S Commandsshow catalog
show cli commandshow cli command <WORD> [mode <mode-name>]
Description: Show Commands Syntax
Syntax:
Command Name pattern between single quotesWORD
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli command <WORD> [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 751
S Commandsshow cli command
show cli internal auditshow cli internal audit
Description: Show Commands Audit
Command Mode: exec : Exec Mode
Command Path:
# show cli internal audit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)752
S Commandsshow cli internal audit
show cli internal transactionshow cli internal transaction logs|xml <NUMBER>
Description: Show Transaction Details
Syntax:
Show Transaction Logslogs
Show Transaction XML Postxml
Transaction ID(TID) to grep log lines with similar TIDs. TID can beextracted from the 'show cli internal audit' command. Number rangefrom=0 to=9223372036854775807
<Transaction ID>
Command Mode: exec : Exec Mode
Command Path:
# show cli internal transaction logs|xml <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 753
S Commandsshow cli internal transaction
show cli listshow cli list [mode <mode-name>]
Description: Show all cli-related commands
Syntax:
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli list [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)754
S Commandsshow cli list
show cli manpageshow cli manpage <WORD> [mode <mode-name>]
Description: Show Commands ManPage
Syntax:
Command Name pattern between single quotesWORD
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli manpage <WORD> [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 755
S Commandsshow cli manpage
show cli pathshow cli path <WORD> [mode <mode-name>]
Description: Show Commands Path
Syntax:
Command Name pattern between single quotesWORD
(Optional) Mode name pattern between single quotes<mode-name>
(Optional) Show Command Detailsdetails
Command Mode: exec : Exec Mode
Command Path:
# show cli path <WORD> [mode <mode-name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)756
S Commandsshow cli path
show clockshow clock
Description: Show clock information
Command Mode: exec : Exec Mode
Command Path:
# show clock
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 757
S Commandsshow clock
show communication ciphersshow communication ciphers
Description: HTTPS service cipher suite listings
Command Mode: exec : Exec Mode
Command Path:
# show communication ciphers
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)758
S Commandsshow communication ciphers
show communication httpshow communication http
Description: HTTP service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication http
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 759
S Commandsshow communication http
show communication httpsshow communication https
Description: HTTPS service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication https
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)760
S Commandsshow communication https
show communication shellinaboxshow communication shellinabox
Description: Shellinabox service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication shellinabox
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 761
S Commandsshow communication shellinabox
show communication ssh-serviceshow communication ssh-service
Description: SSH service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication ssh-service
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)762
S Commandsshow communication ssh-service
show communication telnetshow communication telnet
Description: Telnet service settings
Command Mode: exec : Exec Mode
Command Path:
# show communication telnet
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 763
S Commandsshow communication telnet
show communication web-requestsshow communication web-requests
Description: Status of last web requests
Command Mode: exec : Exec Mode
Command Path:
# show communication web-requests
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)764
S Commandsshow communication web-requests
show contract-typeshow contract-type WORD
Description: Show Contracts Information Based on Type
Syntax:
whitelist (permit) or blacklist(deny) or oob-mgmt type of contractWORD
Command Mode: exec : Exec Mode
Command Path:
# show contract-type WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 765
S Commandsshow contract-type
show contractshow contract WORD
Description: Show Contracts Information
Syntax:
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show contract WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)766
S Commandsshow contract
show controllershow controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show controller
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 767
S Commandsshow controller
show controller detailshow controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show controller detail [id <node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)768
S Commandsshow controller detail
show coresshow cores
Description: Show all core dumps
Command Mode: exec : Exec Mode
Command Path:
# show cores
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 769
S Commandsshow cores
show debug countershow debug <node-name> <process> counter <counterTopics>
Description: Show Counter information
Syntax:
Node name<node-name>
Process name<process>
Counter Topics<counterTopics>
Command Mode: exec : Exec Mode
Command Path:
# show debug <node-name> <process> counter <counterTopics>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)770
S Commandsshow debug counter
show debug logshow debug <node-name> <process> log
Description: Show log level information
Syntax:
Node name<node-name>
Process name<process>
Command Mode: exec : Exec Mode
Command Path:
# show debug <node-name> <process> log
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 771
S Commandsshow debug log
show dns-addressshow dns-address
Description: Show dns address information
Command Mode: exec : Exec Mode
Command Path:
# show dns-address
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)772
S Commandsshow dns-address
show dns-domainshow dns-domain
Description: Show dns domain information
Command Mode: exec : Exec Mode
Command Path:
# show dns-domain
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 773
S Commandsshow dns-domain
show endpointsshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)774
S Commandsshow endpoints
show endpoints leaf interface ethernetshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet[<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 775
S Commandsshow endpoints leaf interface ethernet
show endpoints leaf interface port-channelshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel<WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)776
S Commandsshow endpoints leaf interface port-channel
show endpoints vpcshow endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan<NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex<fex>]
Description: Show IP endpoints on vpc
Syntax:
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: exec : Exec Mode
Command Path:
# show endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interfacevpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 777
S Commandsshow endpoints vpc
show epgshow epg WORD
Description: Show Application EPG Information
Syntax:
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)778
S Commandsshow epg
show epg detailshow epg WORD detail
Description: Show detailed view of Application EPg
Syntax:
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show epg WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 779
S Commandsshow epg detail
show eventsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show event information
Syntax:
(Optional) Event code<event-code>
(Optional) Event ID<event-ID>
(Optional) Cause<event-value>
(Optional) Event activity in time interval. Number range from=1 to=59last-minutes <num-minutes>
(Optional) Event activity in time interval. Number range from=1 to=23last-hours <num-hours>
(Optional) Event activity in time interval. Number range from=1 to=999last-days <num-days>
(Optional) Event activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Event activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed event informationdetail
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)780
S Commandsshow events
show events controllershow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 781
S Commandsshow events controller
show events controller detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)782
S Commandsshow events controller detail
show events leafshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 783
S Commandsshow events leaf
show events leaf fexshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)784
S Commandsshow events leaf fex
show events leaf fex moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 785
S Commandsshow events leaf fex module
show events leaf interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)786
S Commandsshow events leaf interface ethernet
show events leaf interface l3instanceshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 787
S Commandsshow events leaf interface l3instance
show events leaf interface mgmtshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)788
S Commandsshow events leaf interface mgmt
show events leaf interface portchannelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 789
S Commandsshow events leaf interface portchannel
show events leaf interface tunnelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)790
S Commandsshow events leaf interface tunnel
show events leaf inventory chassisshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
None<ch>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 791
S Commandsshow events leaf inventory chassis
show events leaf inventory fansshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)792
S Commandsshow events leaf inventory fans
show events leaf inventory moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 793
S Commandsshow events leaf inventory module
show events leaf inventory module fabricportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport<fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)794
S Commandsshow events leaf inventory module fabricport
show events leaf inventory module leafportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show information for leaf port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the leaf port number<leafPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport<leafPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 795
S Commandsshow events leaf inventory module leafport
show events leaf inventory powersupplyshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)796
S Commandsshow events leaf inventory powersupply
show events leaf inventory supervisorshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 797
S Commandsshow events leaf inventory supervisor
show events leaf protocolshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)798
S Commandsshow events leaf protocol
show events leaf vpcshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Description: Virtual port channel information
Syntax:
Leaf id<leafId>
pls enter virtual port channel number<vpcPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 799
S Commandsshow events leaf vpc
show events leaf vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)800
S Commandsshow events leaf vrf
show events spineshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 801
S Commandsshow events spine
show events spine interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)802
S Commandsshow events spine interface ethernet
show events spine interface l3instanceshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 803
S Commandsshow events spine interface l3instance
show events spine interface mgmtshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)804
S Commandsshow events spine interface mgmt
show events spine interface tunnelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 805
S Commandsshow events spine interface tunnel
show events spine inventory chassisshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)806
S Commandsshow events spine inventory chassis
show events spine inventory fabricshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 807
S Commandsshow events spine inventory fabric
show events spine inventory fansshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)808
S Commandsshow events spine inventory fans
show events spine inventory moduleshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 809
S Commandsshow events spine inventory module
show events spine inventory module fabricportshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)810
S Commandsshow events spine inventory module fabricport
show events spine inventory powersupplyshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 811
S Commandsshow events spine inventory powersupply
show events spine inventory supervisorshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)812
S Commandsshow events spine inventory supervisor
show events spine inventory systemshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 813
S Commandsshow events spine inventory system
show events spine protocolshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)814
S Commandsshow events spine protocol
show events spine vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 815
S Commandsshow events spine vrf
show events tenantshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)816
S Commandsshow events tenant
show events tenant applicationshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 817
S Commandsshow events tenant application
show events tenant application epgshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)818
S Commandsshow events tenant application epg
show events tenant bridge-domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 819
S Commandsshow events tenant bridge-domain
show events tenant bridge-domain detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)820
S Commandsshow events tenant bridge-domain detail
show events tenant endpointsshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 821
S Commandsshow events tenant endpoints
show events tenant endpoints leaf interface ethernetshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)822
S Commandsshow events tenant endpoints leaf interface ethernet
show events tenant endpoints leaf interface port-channelshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 823
S Commandsshow events tenant endpoints leaf interface port-channel
show events tenant endpoints vpcshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)824
S Commandsshow events tenant endpoints vpc
<A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 825
S Commandsshow events tenant endpoints vpc
show events tenant interface bridge-domainshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)826
S Commandsshow events tenant interface bridge-domain
show events tenant interface bridge-domain detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 827
S Commandsshow events tenant interface bridge-domain detail
show events tenant vrfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)828
S Commandsshow events tenant vrf
show events tenant vrf detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 829
S Commandsshow events tenant vrf detail
show events tenant vrf external-l3 bgpshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)830
S Commandsshow events tenant vrf external-l3 bgp
show events tenant vrf external-l3 bgp nodeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node<101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 831
S Commandsshow events tenant vrf external-l3 bgp node
show events tenant vrf external-l3 eigrpshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)832
S Commandsshow events tenant vrf external-l3 eigrp
show events tenant vrf external-l3 eigrp detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 833
S Commandsshow events tenant vrf external-l3 eigrp detail
show events tenant vrf external-l3 epgshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)834
S Commandsshow events tenant vrf external-l3 epg
show events tenant vrf external-l3 epg detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 835
S Commandsshow events tenant vrf external-l3 epg detail
show events tenant vrf external-l3 epg nameshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)836
S Commandsshow events tenant vrf external-l3 epg name
show events tenant vrf external-l3 epg name detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 837
S Commandsshow events tenant vrf external-l3 epg name detail
show events tenant vrf external-l3 interfacesshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)838
S Commandsshow events tenant vrf external-l3 interfaces
show events tenant vrf external-l3 interfaces detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfacesdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 839
S Commandsshow events tenant vrf external-l3 interfaces detail
show events tenant vrf external-l3 ospfshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)840
S Commandsshow events tenant vrf external-l3 ospf
show events tenant vrf external-l3 ospf detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 841
S Commandsshow events tenant vrf external-l3 ospf detail
show events tenant vrf external-l3 route-mapshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Description: Show command for external-l3 route-map
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name<l3out name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)842
S Commandsshow events tenant vrf external-l3 route-map
show events tenant vrf external-l3 route-map detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name <l3out name>]detail
Description: Show external-l3 route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 route-map [name<l3out name>] detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 843
S Commandsshow events tenant vrf external-l3 route-map detail
show events tenant vrf external-l3 static-routeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)844
S Commandsshow events tenant vrf external-l3 static-route
show events tenant vrf external-l3 static-route detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routedetail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 845
S Commandsshow events tenant vrf external-l3 static-route detail
show events tenant vrf external-l3 static-route nodeshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routenode
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)846
S Commandsshow events tenant vrf external-l3 static-route node
show events tenant vrf external-l3 static-route node detailshow events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show events [code <event-code>] [id <event-ID>] [cause <event-value>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-routenode detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 847
S Commandsshow events tenant vrf external-l3 static-route node detail
show external-l2 epgshow external-l2 epg
Description: Show command for external-l2 epgs
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)848
S Commandsshow external-l2 epg
show external-l2 epg nameshow external-l2 epg name WORD
Description: EPG name to filter on
Syntax:
Name of the EPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg name WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 849
S Commandsshow external-l2 epg name
show external-l2 epg tenantshow external-l2 epg tenant WORD
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l2 epg tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)850
S Commandsshow external-l2 epg tenant
show external-l3 bgpshow external-l3 bgp
Description: Show command for BGP peers
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 851
S Commandsshow external-l3 bgp
show external-l3 bgp tenantshow external-l3 bgp tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)852
S Commandsshow external-l3 bgp tenant
show external-l3 bgp tenant vrfshow external-l3 bgp tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 853
S Commandsshow external-l3 bgp tenant vrf
show external-l3 bgp tenant vrf nodeshow external-l3 bgp tenant <WORD> vrf WORD node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 bgp tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)854
S Commandsshow external-l3 bgp tenant vrf node
show external-l3 eigrpshow external-l3 eigrp
Description: Show command for external-l3 eigrp
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 855
S Commandsshow external-l3 eigrp
show external-l3 eigrp detailshow external-l3 eigrp detail
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)856
S Commandsshow external-l3 eigrp detail
show external-l3 eigrp nodeshow external-l3 eigrp node <101-4000>
Description: node(s) to filter on
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 857
S Commandsshow external-l3 eigrp node
show external-l3 eigrp node detailshow external-l3 eigrp node <101-4000> detail
Description: Show interanl details
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)858
S Commandsshow external-l3 eigrp node detail
show external-l3 eigrp tenantshow external-l3 eigrp tenant <WORD>
Description: tenant(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 859
S Commandsshow external-l3 eigrp tenant
show external-l3 eigrp tenant detailshow external-l3 eigrp tenant <WORD> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)860
S Commandsshow external-l3 eigrp tenant detail
show external-l3 eigrp tenant vrfshow external-l3 eigrp tenant <WORD> vrf WORD
Description: vrf(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 861
S Commandsshow external-l3 eigrp tenant vrf
show external-l3 eigrp tenant vrf detailshow external-l3 eigrp tenant <WORD> vrf WORD detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)862
S Commandsshow external-l3 eigrp tenant vrf detail
show external-l3 eigrp tenant vrf nodeshow external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>
Description: node(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 863
S Commandsshow external-l3 eigrp tenant vrf node
show external-l3 eigrp tenant vrf node detailshow external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 eigrp tenant <WORD> vrf WORD node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)864
S Commandsshow external-l3 eigrp tenant vrf node detail
show external-l3 epgshow external-l3 epg
Description: Show command for external-l3 epgs
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 865
S Commandsshow external-l3 epg
show external-l3 epg detailshow external-l3 epg detail
Description: external-l3 epg in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)866
S Commandsshow external-l3 epg detail
show external-l3 epg nameshow external-l3 epg name <epgName>
Description: EPG name to filter on
Syntax:
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 867
S Commandsshow external-l3 epg name
show external-l3 epg name detailshow external-l3 epg name <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)868
S Commandsshow external-l3 epg name detail
show external-l3 epg tenantshow external-l3 epg tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 869
S Commandsshow external-l3 epg tenant
show external-l3 epg tenant detailshow external-l3 epg tenant <WORD> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)870
S Commandsshow external-l3 epg tenant detail
show external-l3 epg tenant vrfshow external-l3 epg tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 871
S Commandsshow external-l3 epg tenant vrf
show external-l3 epg tenant vrf detailshow external-l3 epg tenant <WORD> vrf WORD detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 epg tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)872
S Commandsshow external-l3 epg tenant vrf detail
show external-l3 interfacesshow external-l3 interfaces
Description: Show command for external-l3 interfaces
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 873
S Commandsshow external-l3 interfaces
show external-l3 interfaces detailshow external-l3 interfaces detail
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)874
S Commandsshow external-l3 interfaces detail
show external-l3 interfaces nodeshow external-l3 interfaces node <101-4000>
Description: node(s) to filter on
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 875
S Commandsshow external-l3 interfaces node
show external-l3 interfaces node detailshow external-l3 interfaces node <101-4000> detail
Description: Show interanl details
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)876
S Commandsshow external-l3 interfaces node detail
show external-l3 interfaces tenantshow external-l3 interfaces tenant <WORD>
Description: tenant(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 877
S Commandsshow external-l3 interfaces tenant
show external-l3 interfaces tenant detailshow external-l3 interfaces tenant <WORD> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)878
S Commandsshow external-l3 interfaces tenant detail
show external-l3 interfaces tenant vrfshow external-l3 interfaces tenant <WORD> vrf WORD
Description: vrf(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 879
S Commandsshow external-l3 interfaces tenant vrf
show external-l3 interfaces tenant vrf detailshow external-l3 interfaces tenant <WORD> vrf WORD detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)880
S Commandsshow external-l3 interfaces tenant vrf detail
show external-l3 interfaces tenant vrf nodeshow external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>
Description: node(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 881
S Commandsshow external-l3 interfaces tenant vrf node
show external-l3 interfaces tenant vrf node detailshow external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 interfaces tenant <WORD> vrf WORD node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)882
S Commandsshow external-l3 interfaces tenant vrf node detail
show external-l3 ospfshow external-l3 ospf
Description: Show command for external-l3 ospf
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 883
S Commandsshow external-l3 ospf
show external-l3 ospf detailshow external-l3 ospf detail
Description: Show interanl details
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)884
S Commandsshow external-l3 ospf detail
show external-l3 ospf nodeshow external-l3 ospf node <101-4000>
Description: node(s) to filter on
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 885
S Commandsshow external-l3 ospf node
show external-l3 ospf node detailshow external-l3 ospf node <101-4000> detail
Description: Show interanl details
Syntax:
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)886
S Commandsshow external-l3 ospf node detail
show external-l3 ospf tenantshow external-l3 ospf tenant <WORD>
Description: tenant(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 887
S Commandsshow external-l3 ospf tenant
show external-l3 ospf tenant detailshow external-l3 ospf tenant <WORD> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)888
S Commandsshow external-l3 ospf tenant detail
show external-l3 ospf tenant vrfshow external-l3 ospf tenant <WORD> vrf WORD
Description: vrf(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 889
S Commandsshow external-l3 ospf tenant vrf
show external-l3 ospf tenant vrf detailshow external-l3 ospf tenant <WORD> vrf WORD detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)890
S Commandsshow external-l3 ospf tenant vrf detail
show external-l3 ospf tenant vrf nodeshow external-l3 ospf tenant <WORD> vrf WORD node <101-4000>
Description: node(s) to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 891
S Commandsshow external-l3 ospf tenant vrf node
show external-l3 ospf tenant vrf node detailshow external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF(s) to filter on (Max Size 64)WORD
Node Range or Node Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 ospf tenant <WORD> vrf WORD node <101-4000> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)892
S Commandsshow external-l3 ospf tenant vrf node detail
show external-l3 route-mapshow external-l3 route-map
Description: Show command for external-l3 route-map
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 893
S Commandsshow external-l3 route-map
show external-l3 route-map detailshow external-l3 route-map detail
Description: Route-map in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)894
S Commandsshow external-l3 route-map detail
show external-l3 route-map nameshow external-l3 route-map name <l3out name>
Description: Route-map name to filter on
Syntax:
Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map name <l3out name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 895
S Commandsshow external-l3 route-map name
show external-l3 route-map name detailshow external-l3 route-map name <l3out name> detail
Description: Route-map in detail with operational status
Syntax:
Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map name <l3out name> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)896
S Commandsshow external-l3 route-map name detail
show external-l3 route-map tenantshow external-l3 route-map tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 897
S Commandsshow external-l3 route-map tenant
show external-l3 route-map tenant detailshow external-l3 route-map tenant <WORD> detail
Description: Route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)898
S Commandsshow external-l3 route-map tenant detail
show external-l3 route-map tenant vrfshow external-l3 route-map tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 899
S Commandsshow external-l3 route-map tenant vrf
show external-l3 route-map tenant vrf detailshow external-l3 route-map tenant <WORD> vrf WORD detail
Description: Route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)900
S Commandsshow external-l3 route-map tenant vrf detail
show external-l3 route-map tenant vrf nodeshow external-l3 route-map tenant <WORD> vrf WORD node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 901
S Commandsshow external-l3 route-map tenant vrf node
show external-l3 route-map tenant vrf node detailshow external-l3 route-map tenant <WORD> vrf WORD node detail
Description: Route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 route-map tenant <WORD> vrf WORD node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)902
S Commandsshow external-l3 route-map tenant vrf node detail
show external-l3 static-routeshow external-l3 static-route
Description: Show command for external-l3 static routes
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 903
S Commandsshow external-l3 static-route
show external-l3 static-route detailshow external-l3 static-route detail
Description: static-route in detail with operational status
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)904
S Commandsshow external-l3 static-route detail
show external-l3 static-route nodeshow external-l3 static-route node
Description: node to filter on
Syntax:
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 905
S Commandsshow external-l3 static-route node
show external-l3 static-route node detailshow external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)906
S Commandsshow external-l3 static-route node detail
show external-l3 static-route tenantshow external-l3 static-route tenant <WORD>
Description: tenant to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 907
S Commandsshow external-l3 static-route tenant
show external-l3 static-route tenant detailshow external-l3 static-route tenant <WORD> detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)908
S Commandsshow external-l3 static-route tenant detail
show external-l3 static-route tenant vrfshow external-l3 static-route tenant <WORD> vrf WORD
Description: vrf to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 909
S Commandsshow external-l3 static-route tenant vrf
show external-l3 static-route tenant vrf detailshow external-l3 static-route tenant <WORD> vrf WORD detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)910
S Commandsshow external-l3 static-route tenant vrf detail
show external-l3 static-route tenant vrf nodeshow external-l3 static-route tenant <WORD> vrf WORD node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 911
S Commandsshow external-l3 static-route tenant vrf node
show external-l3 static-route tenant vrf node detailshow external-l3 static-route tenant <WORD> vrf WORD node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show external-l3 static-route tenant <WORD> vrf WORD node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)912
S Commandsshow external-l3 static-route tenant vrf node detail
show fabric-recovery statusshow fabric-recovery status
Description: Show fabric recovery status
Command Mode: exec : Exec Mode
Command Path:
# show fabric-recovery status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 913
S Commandsshow fabric-recovery status
show faultsshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show fault information
Syntax:
(Optional) Historical informationhistory
(Optional) Fault code<fault-code>
(Optional) Fault ID<fault-ID>
(Optional) Acknowledgment status<yes/no>
(Optional) Lifecycle state<lc-state>
(Optional) Severity<severity-value>
(Optional) Minimum severity<severity-value>
(Optional) Type<fault-type>
(Optional) Cause<fault-value>
(Optional) Fault activity in time interval. Number range from=1 to=59last-minutes <num-minutes>
(Optional) Fault activity in time interval. Number range from=1 to=23last-hours <num-hours>
(Optional) Fault activity in time interval. Number range from=1 to=999last-days <num-days>
(Optional) Fault activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Fault activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed faults informationdetail
command scope<scope>
Command Mode: exec : Exec Mode
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)914
S Commandsshow faults
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes/no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-timestart-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]<scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 915
S Commandsshow faults
show faults controllershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)916
S Commandsshow faults controller
show faults controller detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] controller detail [id<node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 917
S Commandsshow faults controller detail
show faults l4l7-clustershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Device information
Syntax:
(Optional) Name of TenantTenant Name
(Optional) Name of DeviceDevice Cluster Name
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-cluster [tenant<Tenant Name>] [cluster <Device Cluster Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)918
S Commandsshow faults l4l7-cluster
show faults l4l7-graphshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show L4 L7 Graph information
Syntax:
(Optional) Name of Tenant<Tenant Name>
(Optional) Name of Graph<Graph Name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] l4l7-graph [tenant<Tenant Name>] [graph <Graph Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 919
S Commandsshow faults l4l7-graph
show faults leafshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)920
S Commandsshow faults leaf
show faults leaf fexshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex<fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 921
S Commandsshow faults leaf fex
show faults leaf fex moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> fex<fexNum> module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)922
S Commandsshow faults leaf fex module
show faults leaf interface ethernetshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 923
S Commandsshow faults leaf interface ethernet
show faults leaf interface l3instanceshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacel3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)924
S Commandsshow faults leaf interface l3instance
show faults leaf interface mgmtshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 925
S Commandsshow faults leaf interface mgmt
show faults leaf interface portchannelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfaceportchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)926
S Commandsshow faults leaf interface portchannel
show faults leaf interface tunnelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> interfacetunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 927
S Commandsshow faults leaf interface tunnel
show faults leaf inventory chassisshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory chassis <ch>
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
None<ch>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorychassis <ch>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)928
S Commandsshow faults leaf inventory chassis
show faults leaf inventory fansshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 929
S Commandsshow faults leaf inventory fans
show faults leaf inventory moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)930
S Commandsshow faults leaf inventory module
show faults leaf inventory module fabricportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 931
S Commandsshow faults leaf inventory module fabricport
show faults leaf inventory module leafportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show information for leaf port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the leaf port number<leafPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorymodule <lcSlot> leafport <leafPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)932
S Commandsshow faults leaf inventory module leafport
show faults leaf inventory powersupplyshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 933
S Commandsshow faults leaf inventory powersupply
show faults leaf inventory supervisorshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)934
S Commandsshow faults leaf inventory supervisor
show faults leaf protocolshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> protocol<protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 935
S Commandsshow faults leaf protocol
show faults leaf vpcshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc <vpcPort>
Description: Virtual port channel information
Syntax:
Leaf id<leafId>
pls enter virtual port channel number<vpcPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vpc<vpcPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)936
S Commandsshow faults leaf vpc
show faults leaf vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] leaf <leafId> vrf<vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 937
S Commandsshow faults leaf vrf
show faults microsoft domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain
Description: Show Microsoft domain information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)938
S Commandsshow faults microsoft domain
show faults microsoft domain nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD>
Description:Microsoft domain name
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 939
S Commandsshow faults microsoft domain name
show faults microsoft domain name hypervshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> hyperv <WORD>
Description: Show Microsoft Hypervisor information
Syntax:
Microsoft domain nameWORD
HyperV hostnameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> hyperv <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)940
S Commandsshow faults microsoft domain name hyperv
show faults microsoft domain name port-groupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> port-group
Description: Show Microsoft port group information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 941
S Commandsshow faults microsoft domain name port-group
show faults microsoft domain name scvmmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> scvmm <hostname|ip>
Description: Show Microsoft SCVMM information
Syntax:
Microsoft domain nameWORD
SCVMM hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> scvmm <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)942
S Commandsshow faults microsoft domain name scvmm
show faults microsoft domain name vmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm
Description: Show Microsoft VM information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 943
S Commandsshow faults microsoft domain name vm
show faults microsoft domain name vm nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name <WORD> vm name <WORD>
Description: Show detailed Microsoft VM information
Syntax:
Microsoft domain nameWORD
VM NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] microsoft domain name<WORD> vm name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)944
S Commandsshow faults microsoft domain name vm name
show faults spineshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 945
S Commandsshow faults spine
show faults spine interface ethernetshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)946
S Commandsshow faults spine interface ethernet
show faults spine interface l3instanceshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacel3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 947
S Commandsshow faults spine interface l3instance
show faults spine interface mgmtshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)948
S Commandsshow faults spine interface mgmt
show faults spine interface tunnelshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> interfacetunnel <tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 949
S Commandsshow faults spine interface tunnel
show faults spine inventory chassisshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorychassis
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)950
S Commandsshow faults spine inventory chassis
show faults spine inventory fabricshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventoryfabric <fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 951
S Commandsshow faults spine inventory fabric
show faults spine inventory fansshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)952
S Commandsshow faults spine inventory fans
show faults spine inventory moduleshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorymodule <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 953
S Commandsshow faults spine inventory module
show faults spine inventory module fabricportshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorymodule <lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)954
S Commandsshow faults spine inventory module fabricport
show faults spine inventory powersupplyshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 955
S Commandsshow faults spine inventory powersupply
show faults spine inventory supervisorshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)956
S Commandsshow faults spine inventory supervisor
show faults spine inventory systemshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> inventorysystem <sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 957
S Commandsshow faults spine inventory system
show faults spine protocolshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> protocol<protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)958
S Commandsshow faults spine protocol
show faults spine vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] spine <leafId> vrf<vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 959
S Commandsshow faults spine vrf
show faults tenantshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)960
S Commandsshow faults tenant
show faults tenant applicationshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD applicationWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 961
S Commandsshow faults tenant application
show faults tenant application epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD applicationWORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)962
S Commandsshow faults tenant application epg
show faults tenant bridge-domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 963
S Commandsshow faults tenant bridge-domain
show faults tenant bridge-domain detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORDbridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)964
S Commandsshow faults tenant bridge-domain detail
show faults tenant interface bridge-domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 965
S Commandsshow faults tenant interface bridge-domain
show faults tenant interface bridge-domain detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD interfacebridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)966
S Commandsshow faults tenant interface bridge-domain detail
show faults tenant vrfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 967
S Commandsshow faults tenant vrf
show faults tenant vrf detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)968
S Commandsshow faults tenant vrf detail
show faults tenant vrf external-l3 bgpshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 969
S Commandsshow faults tenant vrf external-l3 bgp
show faults tenant vrf external-l3 bgp nodeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)970
S Commandsshow faults tenant vrf external-l3 bgp node
show faults tenant vrf external-l3 eigrpshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 971
S Commandsshow faults tenant vrf external-l3 eigrp
show faults tenant vrf external-l3 eigrp detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)972
S Commandsshow faults tenant vrf external-l3 eigrp detail
show faults tenant vrf external-l3 epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 973
S Commandsshow faults tenant vrf external-l3 epg
show faults tenant vrf external-l3 epg detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)974
S Commandsshow faults tenant vrf external-l3 epg detail
show faults tenant vrf external-l3 epg nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 975
S Commandsshow faults tenant vrf external-l3 epg name
show faults tenant vrf external-l3 epg name detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)976
S Commandsshow faults tenant vrf external-l3 epg name detail
show faults tenant vrf external-l3 interfacesshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 977
S Commandsshow faults tenant vrf external-l3 interfaces
show faults tenant vrf external-l3 interfaces detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)978
S Commandsshow faults tenant vrf external-l3 interfaces detail
show faults tenant vrf external-l3 ospfshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 979
S Commandsshow faults tenant vrf external-l3 ospf
show faults tenant vrf external-l3 ospf detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 ospf detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)980
S Commandsshow faults tenant vrf external-l3 ospf detail
show faults tenant vrf external-l3 static-routeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 981
S Commandsshow faults tenant vrf external-l3 static-route
show faults tenant vrf external-l3 static-route detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)982
S Commandsshow faults tenant vrf external-l3 static-route detail
show faults tenant vrf external-l3 static-route nodeshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 983
S Commandsshow faults tenant vrf external-l3 static-route node
show faults tenant vrf external-l3 static-route node detailshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] tenant WORD vrf WORDexternal-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)984
S Commandsshow faults tenant vrf external-l3 static-route node detail
show faults vmware domainshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain
Description: Show VMware domain information
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 985
S Commandsshow faults vmware domain
show faults vmware domain nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name>
Description: VMware domain name
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)986
S Commandsshow faults vmware domain name
show faults vmware domain name epgshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> epg
Description: Show VMware domain EPG details
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 987
S Commandsshow faults vmware domain name epg
show faults vmware domain name esxshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> esx <esx-ip>
Description: Show VMware ESX information
Syntax:
VMware domain name<name>
ESX IP<esx-ip>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> esx <esx-ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)988
S Commandsshow faults vmware domain name esx
show faults vmware domain name port-groupshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> port-group
Description: Show VMware port group information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 989
S Commandsshow faults vmware domain name port-group
show faults vmware domain name vcentershow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vcenter <hostname|ip>
Description: VMware vCenter ip or hostname
Syntax:
VMware domain name<name>
vCenter hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vcenter <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)990
S Commandsshow faults vmware domain name vcenter
show faults vmware domain name vmshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm
Description: Show VMware VM information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 991
S Commandsshow faults vmware domain name vm
show faults vmware domain name vm nameshow faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>] [severity <severity-value>][min-severity <severity-value>] [type <fault-type>] [cause <fault-value>] [last-minutes <NUMBER>] [last-hours<NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name <name> vm name <vm-name>
Description: Show detailed VMware VM information
Syntax:
VMware domain name<name>
VM Name<vm-name>
Command Mode: exec : Exec Mode
Command Path:
# show faults [history] [code <fault-code>] [id <fault-ID>] [ack <yes|no>] [lc <lc-state>][severity <severity-value>] [min-severity <severity-value>] [type <fault-type>] [cause<fault-value>] [last-minutes <NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] vmware domain name<name> vm name <vm-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)992
S Commandsshow faults vmware domain name vm name
show firmware repositoryshow firmware repository
Description: Show firmware images present in repository
Command Mode: exec : Exec Mode
Command Path:
# show firmware repository
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 993
S Commandsshow firmware repository
show firmware repository detailshow firmware repository detail
Description: Detailed repository information
Command Mode: exec : Exec Mode
Command Path:
# show firmware repository detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)994
S Commandsshow firmware repository detail
show firmware upgrade statusshow firmware upgrade status
Description: Upgrade status of all controllers and switches
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 995
S Commandsshow firmware upgrade status
show firmware upgrade status controller-groupshow firmware upgrade status controller-group
Description: Controller-group upgrade status
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status controller-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)996
S Commandsshow firmware upgrade status controller-group
show firmware upgrade status controller-group detailshow firmware upgrade status controller-group detail
Description: Detailed upgrade status
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status controller-group detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 997
S Commandsshow firmware upgrade status controller-group detail
show firmware upgrade status detailshow firmware upgrade status detail
Description: Detailed upgrade status information
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)998
S Commandsshow firmware upgrade status detail
show firmware upgrade status switch-groupshow firmware upgrade status switch-group <WORD>
Description: Switch-group upgrade status
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status switch-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 999
S Commandsshow firmware upgrade status switch-group
show firmware upgrade status switch-group detailshow firmware upgrade status switch-group <WORD> detail
Description: Detailed upgrade status
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show firmware upgrade status switch-group <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1000
S Commandsshow firmware upgrade status switch-group detail
show healthshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>
Description: Show health score information
Syntax:
(Optional) Historical informationhistory
(Optional) Minimum change in health score percentage. Number rangefrom=-100 to=9999
min-change <percentage change>
(Optional) Maximum health score. Number range from=0 to=100max-hs <maximum health-score>
(Optional) Health activity in time intervalstart-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Health activity in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1001
S Commandsshow health
show health l4l7-clustershow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-cluster [tenant <Tenant Name>] [cluster <Device ClusterName>]
Description: Show L4 L7 Device information
Syntax:
(Optional) Name of TenantTenant Name
(Optional) Name of DeviceDevice Cluster Name
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-cluster [tenant <TenantName>] [cluster <Device Cluster Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1002
S Commandsshow health l4l7-cluster
show health l4l7-graphshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show L4 L7 Graph information
Syntax:
(Optional) Name of Tenant<Tenant Name>
(Optional) Name of Graph<Graph Name>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] l4l7-graph [tenant <TenantName>] [graph <Graph Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1003
S Commandsshow health l4l7-graph
show health leafshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1004
S Commandsshow health leaf
show health leaf fexshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1005
S Commandsshow health leaf fex
show health leaf fex moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> fex <fexNum>module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1006
S Commandsshow health leaf fex module
show health leaf interface ethernetshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface ethernet<phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1007
S Commandsshow health leaf interface ethernet
show health leaf interface l3instanceshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface l3instance<l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1008
S Commandsshow health leaf interface l3instance
show health leaf interface mgmtshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface mgmt<mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1009
S Commandsshow health leaf interface mgmt
show health leaf interface portchannelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interfaceportchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1010
S Commandsshow health leaf interface portchannel
show health leaf interface tunnelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> interface tunnel<tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1011
S Commandsshow health leaf interface tunnel
show health leaf inventory chassisshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis <ch>
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
None<ch>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory chassis<ch>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1012
S Commandsshow health leaf inventory chassis
show health leaf inventory fansshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory fans<ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1013
S Commandsshow health leaf inventory fans
show health leaf inventory moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1014
S Commandsshow health leaf inventory module
show health leaf inventory module fabricportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1015
S Commandsshow health leaf inventory module fabricport
show health leaf inventory module leafportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module <lcSlot> leafport <leafPort>
Description: Show information for leaf port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the leaf port number<leafPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory module<lcSlot> leafport <leafPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1016
S Commandsshow health leaf inventory module leafport
show health leaf inventory powersupplyshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1017
S Commandsshow health leaf inventory powersupply
show health leaf inventory supervisorshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> inventory supervisor<supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1018
S Commandsshow health leaf inventory supervisor
show health leaf protocolshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1019
S Commandsshow health leaf protocol
show health leaf vpcshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>
Description: Virtual port channel information
Syntax:
Leaf id<leafId>
pls enter virtual port channel number<vpcPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vpc <vpcPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1020
S Commandsshow health leaf vpc
show health leaf vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] leaf <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1021
S Commandsshow health leaf vrf
show health spineshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1022
S Commandsshow health spine
show health spine interface ethernetshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface ethernet<phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1023
S Commandsshow health spine interface ethernet
show health spine interface l3instanceshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface l3instance <l3Inst>
Description: L3 instance
Syntax:
Leaf id<leafId>
<L3 instance number><l3Inst>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interfacel3instance <l3Inst>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1024
S Commandsshow health spine interface l3instance
show health spine interface mgmtshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface mgmt<mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1025
S Commandsshow health spine interface mgmt
show health spine interface tunnelshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel <tunnelPort>
Description: Tunnel Interface
Syntax:
Leaf id<leafId>
<Tunnel interface number><tunnelPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> interface tunnel<tunnelPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1026
S Commandsshow health spine interface tunnel
show health spine inventory chassisshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory chassis
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1027
S Commandsshow health spine inventory chassis
show health spine inventory fabricshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fabric<fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1028
S Commandsshow health spine inventory fabric
show health spine inventory fansshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory fans<ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1029
S Commandsshow health spine inventory fans
show health spine inventory moduleshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module<lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1030
S Commandsshow health spine inventory module
show health spine inventory module fabricportshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module <lcSlot> fabricport <fabPort>
Description: Show information for fabric port
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
pls enter the fabric port number<fabPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory module<lcSlot> fabricport <fabPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1031
S Commandsshow health spine inventory module fabricport
show health spine inventory powersupplyshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1032
S Commandsshow health spine inventory powersupply
show health spine inventory supervisorshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1033
S Commandsshow health spine inventory supervisor
show health spine inventory systemshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> inventory system<sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1034
S Commandsshow health spine inventory system
show health spine protocolshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>
Description: Show command for protocol
Syntax:
Leaf id<leafId>
Protocol name<protName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> protocol <protName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1035
S Commandsshow health spine protocol
show health spine vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>
Description: Vrf information
Syntax:
Leaf id<leafId>
pls enter vrf name<vrfPort>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] spine <leafId> vrf <vrfPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1036
S Commandsshow health spine vrf
show health tenantshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1037
S Commandsshow health tenant
show health tenant applicationshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1038
S Commandsshow health tenant application
show health tenant application epgshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD application WORDepg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1039
S Commandsshow health tenant application epg
show health tenant bridge-domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1040
S Commandsshow health tenant bridge-domain
show health tenant bridge-domain detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD bridge-domain WORDdetail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1041
S Commandsshow health tenant bridge-domain detail
show health tenant interface bridge-domainshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1042
S Commandsshow health tenant interface bridge-domain
show health tenant interface bridge-domain detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD interfacebridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1043
S Commandsshow health tenant interface bridge-domain detail
show health tenant vrfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1044
S Commandsshow health tenant vrf
show health tenant vrf detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1045
S Commandsshow health tenant vrf detail
show health tenant vrf external-l3 bgpshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1046
S Commandsshow health tenant vrf external-l3 bgp
show health tenant vrf external-l3 bgp nodeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1047
S Commandsshow health tenant vrf external-l3 bgp node
show health tenant vrf external-l3 eigrpshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1048
S Commandsshow health tenant vrf external-l3 eigrp
show health tenant vrf external-l3 eigrp detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1049
S Commandsshow health tenant vrf external-l3 eigrp detail
show health tenant vrf external-l3 epgshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1050
S Commandsshow health tenant vrf external-l3 epg
show health tenant vrf external-l3 epg detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1051
S Commandsshow health tenant vrf external-l3 epg detail
show health tenant vrf external-l3 epg nameshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1052
S Commandsshow health tenant vrf external-l3 epg name
show health tenant vrf external-l3 epg name detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 epg <epgName> name<epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1053
S Commandsshow health tenant vrf external-l3 epg name detail
show health tenant vrf external-l3 interfacesshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1054
S Commandsshow health tenant vrf external-l3 interfaces
show health tenant vrf external-l3 interfaces detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1055
S Commandsshow health tenant vrf external-l3 interfaces detail
show health tenant vrf external-l3 ospfshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1056
S Commandsshow health tenant vrf external-l3 ospf
show health tenant vrf external-l3 ospf detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 ospf detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1057
S Commandsshow health tenant vrf external-l3 ospf detail
show health tenant vrf external-l3 static-routeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1058
S Commandsshow health tenant vrf external-l3 static-route
show health tenant vrf external-l3 static-route detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1059
S Commandsshow health tenant vrf external-l3 static-route detail
show health tenant vrf external-l3 static-route nodeshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1060
S Commandsshow health tenant vrf external-l3 static-route node
show health tenant vrf external-l3 static-route node detailshow health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show health [history] [min-change <NUMBER>] [max-hs <NUMBER>] [start-time<YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] tenant WORD vrf WORD external-l3static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1061
S Commandsshow health tenant vrf external-l3 static-route node detail
show inband-mgmtshow inband-mgmt
Description: show inband mgmt epgs on all the nodes
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1062
S Commandsshow inband-mgmt
show inband-mgmt controllershow inband-mgmt controller <controller-id> [epg <WORD>]
Description: show inband mgmt epgs on the controller
Syntax:
<controller-id>
(Optional) Epg Name of conusmer epgWORD
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt controller <controller-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1063
S Commandsshow inband-mgmt controller
show inband-mgmt switchshow inband-mgmt switch <switch-id> [epg <WORD>]
Description: show inband mgmt epgs on the node
Syntax:
<switch-id>
(Optional) Epg NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show inband-mgmt switch <switch-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1064
S Commandsshow inband-mgmt switch
show interface bridge-domainshow interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1065
S Commandsshow interface bridge-domain
show interface bridge-domain detailshow interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1066
S Commandsshow interface bridge-domain detail
show ip interface bridge-domainshow ip interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show ip interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1067
S Commandsshow ip interface bridge-domain
show ipv6 interface bridge-domainshow ipv6 interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show ipv6 interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1068
S Commandsshow ipv6 interface bridge-domain
show l4l7-clustershow l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Description: Show L4 L7 Device information
Syntax:
(Optional) Name of TenantTenant Name
(Optional) Name of DeviceDevice Cluster Name
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-cluster [tenant <Tenant Name>] [cluster <Device Cluster Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1069
S Commandsshow l4l7-cluster
show l4l7-graphshow l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Description: Show L4 L7 Graph information
Syntax:
(Optional) Name of Tenant<Tenant Name>
(Optional) Name of Graph<Graph Name>
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-graph [tenant <Tenant Name>] [graph <Graph Name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1070
S Commandsshow l4l7-graph
show l4l7-packageshow l4l7-package
Description: Show L4-L7 package information
Command Mode: exec : Exec Mode
Command Path:
# show l4l7-package
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1071
S Commandsshow l4l7-package
show ldap-servershow ldap-server
Description: Show LDAP server information
Command Mode: exec : Exec Mode
Command Path:
# show ldap-server
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1072
S Commandsshow ldap-server
show locator-ledshow locator-led status
Description: Show command for locator-led
Syntax:
locator-led statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show locator-led status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1073
S Commandsshow locator-led
show locator-led status leafshow locator-led status leaf
Description: Leaf to filter on
Syntax:
locator-led statusstatus
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show locator-led status leaf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1074
S Commandsshow locator-led status leaf
show microsoft domainshow microsoft domain
Description: Show Microsoft domain information
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1075
S Commandsshow microsoft domain
show microsoft domain nameshow microsoft domain name <WORD>
Description:Microsoft domain name
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1076
S Commandsshow microsoft domain name
show microsoft domain name hypervshow microsoft domain name <WORD> hyperv <WORD>
Description: Show Microsoft Hypervisor information
Syntax:
Microsoft domain nameWORD
HyperV hostnameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> hyperv <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1077
S Commandsshow microsoft domain name hyperv
show microsoft domain name port-groupshow microsoft domain name <WORD> port-group
Description: Show Microsoft port group information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1078
S Commandsshow microsoft domain name port-group
show microsoft domain name scvmmshow microsoft domain name <WORD> scvmm <hostname|ip>
Description: Show Microsoft SCVMM information
Syntax:
Microsoft domain nameWORD
SCVMM hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> scvmm <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1079
S Commandsshow microsoft domain name scvmm
show microsoft domain name vmshow microsoft domain name <WORD> vm
Description: Show Microsoft VM information
Syntax:
Microsoft domain nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1080
S Commandsshow microsoft domain name vm
show microsoft domain name vm nameshow microsoft domain name <WORD> vm name <WORD>
Description: Show detailed Microsoft VM information
Syntax:
Microsoft domain nameWORD
VM NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show microsoft domain name <WORD> vm name <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1081
S Commandsshow microsoft domain name vm name
show microsoft vmshow microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]
Description: Show Microsoft VM information
Syntax:
(Optional) Specify a VM nameWORD
(Optional) Specify a VM IP addressA.B.C.D
(Optional) Specify a VM MAC addressAA:BB:CC:DD:EE:FF
Command Mode: exec : Exec Mode
Command Path:
# show microsoft vm [name <WORD>] [ip <A.B.C.D>] [mac <AA:BB:CC:DD:EE:FF>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1082
S Commandsshow microsoft vm
show monitor accessshow monitor access session session_name
Description: Show monitor session for access interfaces
Syntax:
sessionsession
session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show monitor access session session_name
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1083
S Commandsshow monitor access
show monitor fabricshow monitor fabric session session_name
Description: Show monitor session for fabric interfaces
Syntax:
sessionsession
session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show monitor fabric session session_name
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1084
S Commandsshow monitor fabric
show monitor tenantshow monitor tenant <tenant_name> session session_name
Description: Show monitor session for tenant
Syntax:
tenanttenant_name
sessionsession
session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show monitor tenant <tenant_name> session session_name
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1085
S Commandsshow monitor tenant
show monitor virtualshow monitor virtual session WORD
Description: Show monitor session for virtual switches
Syntax:
sessionsession
Session nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show monitor virtual session WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1086
S Commandsshow monitor virtual
show ntpqshow ntpq
Description: Show ntpq information
Command Mode: exec : Exec Mode
Command Path:
# show ntpq
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1087
S Commandsshow ntpq
show oob-mgmtshow oob-mgmt
Description: Show Out of band Information
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1088
S Commandsshow oob-mgmt
show oob-mgmt controllershow oob-mgmt controller <controller-id> [epg <WORD>]
Description: show oob mgmt epgs on the controller, enter one
Syntax:
<controller-id>
(Optional) Epg Name of conusmer epgWORD
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt controller <controller-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1089
S Commandsshow oob-mgmt controller
show oob-mgmt switchshow oob-mgmt switch <switch-id> [epg <WORD>]
Description: show oob mgmt epgs on the node, enter one
Syntax:
<switch-id>
(Optional) Epg Name of conusmer epgWORD
Command Mode: exec : Exec Mode
Command Path:
# show oob-mgmt switch <switch-id> [epg <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1090
S Commandsshow oob-mgmt switch
show policy-mapshow policy-map
Description: Show policy maps
Command Mode: exec : Exec Mode
Command Path:
# show policy-map
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1091
S Commandsshow policy-map
show policy-map type data-planeshow policy-map type data-plane infra WORD
Description: data-plane type policy-map(s)
Syntax:
Global data-plane policy-map(s)infra
data-plane type policy-map(s) (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show policy-map type data-plane infra WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1092
S Commandsshow policy-map type data-plane
show policy-map type qosshow policy-map type qos WORD
Description: QOS type policy-map(s)
Syntax:
QOS type policy-map(s) (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show policy-map type qos WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1093
S Commandsshow policy-map type qos
show port-channel leafshow port-channel leaf WORD <port-channel-list>
Description: show leaf port-channel info
Syntax:
Leaf Range or Leaf Name ListWORD
port channel names<port-channel-list>
Command Mode: exec : Exec Mode
Command Path:
# show port-channel leaf WORD <port-channel-list>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1094
S Commandsshow port-channel leaf
show port-channel mapshow port-channel map <port-channel-list>
Description: show port-channel mapping
Syntax:
port channel names<port-channel-list>
Command Mode: exec : Exec Mode
Command Path:
# show port-channel map <port-channel-list>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1095
S Commandsshow port-channel map
show port-channel map leafshow port-channel map <port-channel-list> leaf WORD [fex <101-164>]
Description: leaf
Syntax:
port channel names<port-channel-list>
Leaf Range or Leaf Name ListWORD
(Optional) Fex ID<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show port-channel map <port-channel-list> leaf WORD [fex <101-164>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1096
S Commandsshow port-channel map leaf
show radius-servershow radius-server
Description: Show RADIUS server information
Command Mode: exec : Exec Mode
Command Path:
# show radius-server
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1097
S Commandsshow radius-server
show resourceshow resource conflict encap-vlan
Description: resource
Syntax:
show resource conflicts in APICconflict
show resource conflicts of encap-vlan in APICencap-vlan
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1098
S Commandsshow resource
show resource conflict encap-vlan epgshow resource conflict encap-vlan epg <WORD>
Description: Epg Name
Syntax:
show resource conflicts in APICconflict
show resource conflicts of encap-vlan in APICencap-vlan
Epg NameWORD
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1099
S Commandsshow resource conflict encap-vlan epg
show resource conflict encap-vlan epg nodeshow resource conflict encap-vlan epg <WORD> node <101-4000>
Description: Node ID
Syntax:
show resource conflicts in APICconflict
show resource conflicts of encap-vlan in APICencap-vlan
Epg NameWORD
Leaf ID<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show resource conflict encap-vlan epg <WORD> node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1100
S Commandsshow resource conflict encap-vlan epg node
show roleshow role
Description: Show information about AAA Roles
Command Mode: exec : Exec Mode
Command Path:
# show role
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1101
S Commandsshow role
show running-configshow running-config [all] <scope>
Description: show running configuration
Syntax:
(Optional) show running-config with defaultsall
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show running-config [all] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1102
S Commandsshow running-config
show sessionsshow sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes <NUMBER>][last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time end-time<YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Description: Show session-log information
Syntax:
(Optional) Log ID<log-id>
(Optional) Object action indicatoraction<action-type>
(Optional) Name of user<user-name>
(Optional) Logs created in time interval. Number range from=1 to=59<num-minutes>
(Optional) Logs created in time interval. Number range from=1 to=23<num-hours>
(Optional) Logs created in time interval. Number range from=1 to=999<num-days>
(Optional) Logs created in time interval<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Logs created in time intervalend-time<YYYY-MM-DDTHR:MIN:SEC>
(Optional) Detailed session-log information. Displays the action triggerthat shows why a login occurred.
detail
command scope<scope>
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action action<action-type>] [user <user-name>] [last-minutes<NUMBER>] [last-hours <NUMBER>] [last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>][end-time end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail] <scope>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1103
S Commandsshow sessions
show sessions controllershow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]controller
Description: Show controller information
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] controller
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1104
S Commandsshow sessions controller
show sessions controller detailshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]controller detail [id <node-id>]
Description: Detailed controller information
Syntax:
(Optional) Optional Serial numbernode-id
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] controller detail [id <node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1105
S Commandsshow sessions controller detail
show sessions leafshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1106
S Commandsshow sessions leaf
show sessions spineshow sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>] [last-days<NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>] [detail]spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show sessions [id <log-id>] [action <action-type>] [user <user-name>] [last-hours <NUMBER>][last-days <NUMBER>] [start-time <YYYY-MM-DDTHR:MIN:SEC>] [end-time <YYYY-MM-DDTHR:MIN:SEC>][detail] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1107
S Commandsshow sessions spine
show snapshot activeshow snapshot active job
Description: Show command for active snapshot job
Syntax:
View active snapshot jobjob
Command Mode: exec : Exec Mode
Command Path:
# show snapshot active job
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1108
S Commandsshow snapshot active
show snapshot filesshow snapshot files
Description: Show command for snapshot files
Command Mode: exec : Exec Mode
Command Path:
# show snapshot files
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1109
S Commandsshow snapshot files
show snapshot jobsshow snapshot jobs
Description: Show command for snapshot jobs
Command Mode: exec : Exec Mode
Command Path:
# show snapshot jobs
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1110
S Commandsshow snapshot jobs
show snmpshow snmp [policy <policy>]
Description: Show snmp policy information
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1111
S Commandsshow snmp
show snmp clientgroupsshow snmp [policy <policy>] clientgroups
Description: Show snmp client group policies
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] clientgroups
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1112
S Commandsshow snmp clientgroups
show snmp communityshow snmp [policy <policy>] community
Description: Show snmp community information
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] community
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1113
S Commandsshow snmp community
show snmp engineidshow snmp [policy <policy>] engineid
Description: Show snmp v3 engine-id
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] engineid
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1114
S Commandsshow snmp engineid
show snmp hostsshow snmp [policy <policy>] hosts
Description: Show snmp trap hosts
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] hosts
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1115
S Commandsshow snmp hosts
show snmp usersshow snmp [policy <policy>] users
Description: Show snmp v3 users
Syntax:
(Optional) SNMP policy namepolicy
Command Mode: exec : Exec Mode
Command Path:
# show snmp [policy <policy>] users
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1116
S Commandsshow snmp users
show statsshow stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine
Description: Show statistics
Syntax:
Choose granularity valuegranularity
<granularity-value><granularity-value>
(Optional) historical stats informationhistory
(Optional) cumulative stats informationcumulative
command scopetenant
command scopeleaf
command scopespine
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant|leaf|spine
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1117
S Commandsshow stats
show stats granularity leafshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId>
Description: Show command for leaf
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1118
S Commandsshow stats granularity leaf
show stats granularity leaf fexshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum>
Description: Show extended chassis information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex<fexNum>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1119
S Commandsshow stats granularity leaf fex
show stats granularity leaf fex moduleshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex <fexNum> module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
pls enter fex number<fexNum>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> fex<fexNum> module <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1120
S Commandsshow stats granularity leaf fex module
show stats granularity leaf interface ethernetshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1121
S Commandsshow stats granularity leaf interface ethernet
show stats granularity leaf interface mgmtshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1122
S Commandsshow stats granularity leaf interface mgmt
show stats granularity leaf interface portchannelshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interface portchannel <portChan>
Description: Port channel interface
Syntax:
Leaf id<leafId>
<Port channel number><portChan>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> interfaceportchannel <portChan>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1123
S Commandsshow stats granularity leaf interface portchannel
show stats granularity leaf inventory fansshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1124
S Commandsshow stats granularity leaf inventory fans
show stats granularity leaf inventory powersupplyshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory powersupply <psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1125
S Commandsshow stats granularity leaf inventory powersupply
show stats granularity leaf inventory supervisorshow stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] leaf <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1126
S Commandsshow stats granularity leaf inventory supervisor
show stats granularity spineshow stats granularity <granularity-value> [history] [cumulative] spine <leafId>
Description: Show command for spine
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1127
S Commandsshow stats granularity spine
show stats granularity spine interface ethernetshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface ethernet <phyInt>
Description: Ethernet IEEE 802.3z
Syntax:
Leaf id<leafId>
<slot or chassis-number/port or slot number><phyInt>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interfaceethernet <phyInt>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1128
S Commandsshow stats granularity spine interface ethernet
show stats granularity spine interface mgmtshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> interface mgmt <mgmtPort>
Description:Management interface
Syntax:
Leaf id<leafId>
<Management interface number><mgmtPort>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> interfacemgmt <mgmtPort>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1129
S Commandsshow stats granularity spine interface mgmt
show stats granularity spine inventory chassisshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory chassis
Description: Show inventory chassis information
Syntax:
Leaf id<leafId>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorychassis
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1130
S Commandsshow stats granularity spine inventory chassis
show stats granularity spine inventory fabricshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fabric <fcMod>
Description: Show information for fabric module
Syntax:
Leaf id<leafId>
pls enter the fabric module number<fcMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventoryfabric <fcMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1131
S Commandsshow stats granularity spine inventory fabric
show stats granularity spine inventory fansshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory fans <ftSlot>
Description: Show inventory fan information
Syntax:
Leaf id<leafId>
pls enter fan tray number<ftSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventoryfans <ftSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1132
S Commandsshow stats granularity spine inventory fans
show stats granularity spine inventory moduleshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory module <lcSlot>
Description: Show inventory module information
Syntax:
Leaf id<leafId>
please enter the module number<lcSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorymodule <lcSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1133
S Commandsshow stats granularity spine inventory module
show stats granularity spine inventory powersupplyshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory powersupply<psuSlot>
Description: Show inventory power supply information
Syntax:
Leaf id<leafId>
pls enter the powersupply number<psuSlot>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorypowersupply <psuSlot>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1134
S Commandsshow stats granularity spine inventory powersupply
show stats granularity spine inventory supervisorshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory supervisor <supMod>
Description: Show information for supervisor module
Syntax:
Leaf id<leafId>
pls enter the supervisor module number<supMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorysupervisor <supMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1135
S Commandsshow stats granularity spine inventory supervisor
show stats granularity spine inventory systemshow stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventory system <sysMod>
Description: Show information for system module
Syntax:
Leaf id<leafId>
pls enter the system module number<sysMod>
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] spine <leafId> inventorysystem <sysMod>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1136
S Commandsshow stats granularity spine inventory system
show stats granularity tenantshow stats granularity <granularity-value> [history] [cumulative] tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1137
S Commandsshow stats granularity tenant
show stats granularity tenant applicationshow stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD applicationWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1138
S Commandsshow stats granularity tenant application
show stats granularity tenant application epgshow stats granularity <granularity-value> [history] [cumulative] tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show stats granularity <granularity-value> [history] [cumulative] tenant WORD applicationWORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1139
S Commandsshow stats granularity tenant application epg
show switchshow switch
Description: Show switch information
Command Mode: exec : Exec Mode
Command Path:
# show switch
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1140
S Commandsshow switch
show switch detailshow switch detail [id <switch-id>]
Description: Show switch detailed information
Syntax:
(Optional) Optional switch id. Number range from=0to=9223372036854775807
switch-id
Command Mode: exec : Exec Mode
Command Path:
# show switch detail [id <switch-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1141
S Commandsshow switch detail
show tacacs-servershow tacacs-server
Description: Show tacacs server information
Command Mode: exec : Exec Mode
Command Path:
# show tacacs-server
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1142
S Commandsshow tacacs-server
show techsupport allshow techsupport all status
Description: Techsupport status for all
Syntax:
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport all status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1143
S Commandsshow techsupport all
show techsupport controllersshow techsupport controllers status
Description: Techsupport status for controllers
Syntax:
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport controllers status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1144
S Commandsshow techsupport controllers
show techsupport hostshow techsupport host <NUMBER> status
Description: Techsupport status for host
Syntax:
Specify the host Odev ID. Number range from=0to=9223372036854775807
<Odevid>
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport host <NUMBER> status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1145
S Commandsshow techsupport host
show techsupport switchshow techsupport switch switchId <switchId> status
Description: Techsupport status for switch
Syntax:
switch id 101-4000 or range(s): 101-103,104switchId <switchId>
Statusstatus
Command Mode: exec : Exec Mode
Command Path:
# show techsupport switch switchId <switchId> status
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1146
S Commandsshow techsupport switch
show tenantshow tenant WORD
Description: Show Tenants Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1147
S Commandsshow tenant
show tenant access-listshow tenant WORD access-list WORD
Description: Show Access-list Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD access-list WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1148
S Commandsshow tenant access-list
show tenant applicationshow tenant WORD application WORD
Description: Show Application Profiles Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1149
S Commandsshow tenant application
show tenant application endpointsshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1150
S Commandsshow tenant application endpoints
show tenant application endpoints leaf interface ethernetshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf<WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1151
S Commandsshow tenant application endpoints leaf interface ethernet
show tenant application endpoints leaf interface port-channelshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf<WORD> interface port-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1152
S Commandsshow tenant application endpoints leaf interface port-channel
show tenant application endpoints vpcshow tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpccontext <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1153
S Commandsshow tenant application endpoints vpc
show tenant application epgshow tenant WORD application WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1154
S Commandsshow tenant application epg
show tenant application epg detailshow tenant WORD application WORD epg WORD detail
Description: Show detailed view of Application EPg
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1155
S Commandsshow tenant application epg detail
show tenant application epg endpointsshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1156
S Commandsshow tenant application epg endpoints
show tenant application epg endpoints leaf interface ethernetshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface ethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1157
S Commandsshow tenant application epg endpoints leaf interface ethernet
show tenant application epg endpoints leaf interfaceport-channel
show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1158
S Commandsshow tenant application epg endpoints leaf interface port-channel
show tenant application epg endpoints vpcshow tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the application we eventually want to filter on (Max Size 64)WORD
Name of the AEPG to filter on (Max Size 64)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD application WORD epg WORD endpoints [type <type>] [mac <E.E.E
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1159
S Commandsshow tenant application epg endpoints vpc
EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6<A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1160
S Commandsshow tenant application epg endpoints vpc
show tenant bridge-domainshow tenant WORD bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1161
S Commandsshow tenant bridge-domain
show tenant bridge-domain detailshow tenant WORD bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1162
S Commandsshow tenant bridge-domain detail
show tenant contract-typeshow tenant WORD contract-type WORD
Description: Show Contracts Information Based on Type
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
whitelist (permit) or blacklist(deny) or oob-mgmt type of contractWORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD contract-type WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1163
S Commandsshow tenant contract-type
show tenant contractshow tenant WORD contract WORD
Description: Show Contracts Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the Contract to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD contract WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1164
S Commandsshow tenant contract
show tenant detailshow tenant WORD detail
Description: Show detailed view of tenant
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1165
S Commandsshow tenant detail
show tenant endpointsshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Description: Show IP endpoints
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1166
S Commandsshow tenant endpoints
show tenant endpoints leaf interface ethernetshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface ethernet ethernet[<fex>/]<slot>/<port>
Description: Show IP endpoints on an interface ethernet
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Ethernet Rangeethernet [<fex>/]<slot>/<port>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceethernet ethernet [<fex>/]<slot>/<port>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1167
S Commandsshow tenant endpoints leaf interface ethernet
show tenant endpoints leaf interface port-channelshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interface port-channel <WORD> [fex<NUMBER>]
Description: Show IP endpoints on an interface port-channel
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
Leaf Number (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Port Channel Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] leaf <WORD> interfaceport-channel <WORD> [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1168
S Commandsshow tenant endpoints leaf interface port-channel
show tenant endpoints vpcshow tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE>] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD> <WORD> interface vpc <WORD>[fex <fex>]
Description: Show IP endpoints on vpc
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
(Optional) Endpoint Typetype
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
(Optional) Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) IPv6 address in format xxxx:xxxx, xxxx::xxA:B::C:D
VPC Contextcontext
First VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
Second VPC leaf (Max Size 4000). Number range from=0to=9223372036854775807
WORD
VPC Interface nameinterface
VPC Interface namevpc
VPC Name (Max Size 64)WORD
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD endpoints [type <type>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >] [vlan <NUMBER>] [ip <A.B.C.D>] [ipv6 <A:B::C:D>] vpc context <WORD><WORD> interface vpc <WORD> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1169
S Commandsshow tenant endpoints vpc
show tenant epgshow tenant WORD epg WORD
Description: Show Application EPG Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1170
S Commandsshow tenant epg
show tenant epg detailshow tenant WORD epg WORD detail
Description: Show detailed view of Application EPg
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the AEPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD epg WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1171
S Commandsshow tenant epg detail
show tenant external-l2 epgshow tenant WORD external-l2 epg WORD
Description: Show command for external-l2 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the EPG to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD external-l2 epg WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1172
S Commandsshow tenant external-l2 epg
show tenant interface bridge-domainshow tenant WORD interface bridge-domain WORD
Description: Show Bridge-domain Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1173
S Commandsshow tenant interface bridge-domain
show tenant interface bridge-domain detailshow tenant WORD interface bridge-domain WORD detail
Description: Show Bridge-domain Detailed Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD interface bridge-domain WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1174
S Commandsshow tenant interface bridge-domain detail
show tenant ip interface bridge-domainshow tenant WORD ip interface bridge-domain WORD
Description: Show command for IP properties on interface BD
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD ip interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1175
S Commandsshow tenant ip interface bridge-domain
show tenant ipv6 interface bridge-domainshow tenant WORD ipv6 interface bridge-domain WORD
Description: Show command for IP properties on interface BD
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the bridge-domain (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD ipv6 interface bridge-domain WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1176
S Commandsshow tenant ipv6 interface bridge-domain
show tenant policy-mapshow tenant WORD policy-map
Description: Show policy maps
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1177
S Commandsshow tenant policy-map
show tenant policy-map type data-planeshow tenant WORD policy-map type data-plane WORD
Description: data-plane type policy-map(s)
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
data-plane type policy-map(s) (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map type data-plane WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1178
S Commandsshow tenant policy-map type data-plane
show tenant policy-map type qosshow tenant WORD policy-map type qos WORD
Description: QOS type policy-map(s)
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
QOS type policy-map(s) (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD policy-map type qos WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1179
S Commandsshow tenant policy-map type qos
show tenant vrfshow tenant WORD vrf WORD
Description: Show VRF Information
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1180
S Commandsshow tenant vrf
show tenant vrf detailshow tenant WORD vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1181
S Commandsshow tenant vrf detail
show tenant vrf external-l3 bgpshow tenant WORD vrf WORD external-l3 bgp
Description: Show command for BGP peers
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 bgp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1182
S Commandsshow tenant vrf external-l3 bgp
show tenant vrf external-l3 bgp nodeshow tenant WORD vrf WORD external-l3 bgp node <101-4000>
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name List<101-4000>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 bgp node <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1183
S Commandsshow tenant vrf external-l3 bgp node
show tenant vrf external-l3 eigrpshow tenant WORD vrf WORD external-l3 eigrp
Description: Show external l3 EIGRP
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 eigrp
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1184
S Commandsshow tenant vrf external-l3 eigrp
show tenant vrf external-l3 eigrp detailshow tenant WORD vrf WORD external-l3 eigrp detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 eigrp detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1185
S Commandsshow tenant vrf external-l3 eigrp detail
show tenant vrf external-l3 epgshow tenant WORD vrf WORD external-l3 epg <epgName>
Description: Show command for external-l3 epgs
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1186
S Commandsshow tenant vrf external-l3 epg
show tenant vrf external-l3 epg detailshow tenant WORD vrf WORD external-l3 epg <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1187
S Commandsshow tenant vrf external-l3 epg detail
show tenant vrf external-l3 epg nameshow tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Description: EPG name to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1188
S Commandsshow tenant vrf external-l3 epg name
show tenant vrf external-l3 epg name detailshow tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Description: external-l3 epg in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Name of the EPG to filter on<epgName>
Name of the EPG to filter on<epgName>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 epg <epgName> name <epgName> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1189
S Commandsshow tenant vrf external-l3 epg name detail
show tenant vrf external-l3 interfacesshow tenant WORD vrf WORD external-l3 interfaces
Description: Show tenant <tenant> vrf <vrf> external l3 interfaces
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 interfaces
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1190
S Commandsshow tenant vrf external-l3 interfaces
show tenant vrf external-l3 interfaces detailshow tenant WORD vrf WORD external-l3 interfaces detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 interfaces detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1191
S Commandsshow tenant vrf external-l3 interfaces detail
show tenant vrf external-l3 ospfshow tenant WORD vrf WORD external-l3 ospf
Description: Show commad for IPv4 and IPv6 external l3 OSPF configuration
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 ospf
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1192
S Commandsshow tenant vrf external-l3 ospf
show tenant vrf external-l3 ospf detailshow tenant WORD vrf WORD external-l3 ospf detail
Description: Show interanl details
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 ospf detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1193
S Commandsshow tenant vrf external-l3 ospf detail
show tenant vrf external-l3 route-mapshow tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Description: Show command for external-l3 route-map
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1194
S Commandsshow tenant vrf external-l3 route-map
show tenant vrf external-l3 route-map detailshow tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail
Description: Show external-l3 route-map in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
(Optional) Name of the route-map to filter on<l3out name>
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 route-map [name <l3out name>] detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1195
S Commandsshow tenant vrf external-l3 route-map detail
show tenant vrf external-l3 static-routeshow tenant WORD vrf WORD external-l3 static-route
Description: Show command for external-l3 static routes
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1196
S Commandsshow tenant vrf external-l3 static-route
show tenant vrf external-l3 static-route detailshow tenant WORD vrf WORD external-l3 static-route detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1197
S Commandsshow tenant vrf external-l3 static-route detail
show tenant vrf external-l3 static-route nodeshow tenant WORD vrf WORD external-l3 static-route node
Description: node to filter on
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route node
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1198
S Commandsshow tenant vrf external-l3 static-route node
show tenant vrf external-l3 static-route node detailshow tenant WORD vrf WORD external-l3 static-route node detail
Description: static-route in detail with operational status
Syntax:
Name of the tenant to filter on (Max Size 63)WORD
Name of the VRF to filter on (Max Size 64)WORD
Leaf Range or Leaf Name Listarg
Command Mode: exec : Exec Mode
Command Path:
# show tenant WORD vrf WORD external-l3 static-route node detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1199
S Commandsshow tenant vrf external-l3 static-route node detail
show troubleshoot epext sessionshow troubleshoot epext session <session_name>
Description: Show session
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1200
S Commandsshow troubleshoot epext session
show troubleshoot epext session atomiccountershow troubleshoot epext session <session_name> atomiccounter
Description: Show atomic counters
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> atomiccounter
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1201
S Commandsshow troubleshoot epext session atomiccounter
show troubleshoot epext session auditshow troubleshoot epext session <session_name> audit
Description: Show audit
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> audit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1202
S Commandsshow troubleshoot epext session audit
show troubleshoot epext session contractsshow troubleshoot epext session <session_name> contracts
Description: Show contracts
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> contracts
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1203
S Commandsshow troubleshoot epext session contracts
show troubleshoot epext session deploymentsshow troubleshoot epext session <session_name> deployments
Description: Show deployment changes
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> deployments
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1204
S Commandsshow troubleshoot epext session deployments
show troubleshoot epext session eventsshow troubleshoot epext session <session_name> events
Description: Show events
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> events
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1205
S Commandsshow troubleshoot epext session events
show troubleshoot epext session faultsshow troubleshoot epext session <session_name> faults
Description: Show faults
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> faults
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1206
S Commandsshow troubleshoot epext session faults
show troubleshoot epext session monitorshow troubleshoot epext session <session_name> monitor
Description: Show monitor
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> monitor
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1207
S Commandsshow troubleshoot epext session monitor
show troubleshoot epext session reportsshow troubleshoot epext session <session_name> reports
Description: Show reports
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> reports
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1208
S Commandsshow troubleshoot epext session reports
show troubleshoot epext session statisticsshow troubleshoot epext session <session_name> statistics
Description: Show statistics
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> statistics
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1209
S Commandsshow troubleshoot epext session statistics
show troubleshoot epext session topologyshow troubleshoot epext session <session_name> topology
Description: Show topology
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> topology
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1210
S Commandsshow troubleshoot epext session topology
show troubleshoot epext session tracerouteshow troubleshoot epext session <session_name> traceroute
Description: Show traceroute
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext session <session_name> traceroute
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1211
S Commandsshow troubleshoot epext session traceroute
show troubleshoot epext sessionsshow troubleshoot epext sessions
Description: Show sessions
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot epext sessions
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1212
S Commandsshow troubleshoot epext sessions
show troubleshoot eptoep sessionshow troubleshoot eptoep session <session_name>
Description: Show session
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1213
S Commandsshow troubleshoot eptoep session
show troubleshoot eptoep session atomiccountershow troubleshoot eptoep session <session_name> atomiccounter
Description: Show atomic counters
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> atomiccounter
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1214
S Commandsshow troubleshoot eptoep session atomiccounter
show troubleshoot eptoep session auditshow troubleshoot eptoep session <session_name> audit
Description: Show audit
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> audit
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1215
S Commandsshow troubleshoot eptoep session audit
show troubleshoot eptoep session contractsshow troubleshoot eptoep session <session_name> contracts
Description: Show contracts
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> contracts
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1216
S Commandsshow troubleshoot eptoep session contracts
show troubleshoot eptoep session deploymentsshow troubleshoot eptoep session <session_name> deployments
Description: Show deployment changes
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> deployments
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1217
S Commandsshow troubleshoot eptoep session deployments
show troubleshoot eptoep session eventsshow troubleshoot eptoep session <session_name> events
Description: Show events
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> events
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1218
S Commandsshow troubleshoot eptoep session events
show troubleshoot eptoep session faultsshow troubleshoot eptoep session <session_name> faults
Description: Show faults
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> faults
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1219
S Commandsshow troubleshoot eptoep session faults
show troubleshoot eptoep session monitorshow troubleshoot eptoep session <session_name> monitor
Description: Show monitor
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> monitor
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1220
S Commandsshow troubleshoot eptoep session monitor
show troubleshoot eptoep session reportsshow troubleshoot eptoep session <session_name> reports
Description: Show reports
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> reports
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1221
S Commandsshow troubleshoot eptoep session reports
show troubleshoot eptoep session statisticsshow troubleshoot eptoep session <session_name> statistics
Description: Show statistics
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> statistics
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1222
S Commandsshow troubleshoot eptoep session statistics
show troubleshoot eptoep session topologyshow troubleshoot eptoep session <session_name> topology
Description: Show topology
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> topology
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1223
S Commandsshow troubleshoot eptoep session topology
show troubleshoot eptoep session tracerouteshow troubleshoot eptoep session <session_name> traceroute
Description: Show traceroute
Syntax:
Session namesession_name
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep session <session_name> traceroute
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1224
S Commandsshow troubleshoot eptoep session traceroute
show troubleshoot eptoep sessionsshow troubleshoot eptoep sessions
Description: Show sessions
Command Mode: exec : Exec Mode
Command Path:
# show troubleshoot eptoep sessions
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1225
S Commandsshow troubleshoot eptoep sessions
show usernameshow username <WORD>
Description: Show user information
Syntax:
User nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show username <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1226
S Commandsshow username
show username detailshow username <WORD> detail
Description: Show user information
Syntax:
User nameWORD
Command Mode: exec : Exec Mode
Command Path:
# show username <WORD> detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1227
S Commandsshow username detail
show versionshow version
Description: Show version information
Command Mode: exec : Exec Mode
Command Path:
# show version
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1228
S Commandsshow version
show vlan-domainshow vlan-domain [name <arg>] [vlan] [leaf <arg>] [detail]
Description: Show command for vlan-domain
Syntax:
(Optional) Vlan-domain namearg
(Optional) VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19<vlan-range>
(Optional) Leaf id. Number range from=101 to=4000arg
(Optional) vlan-domain in detail with concrete MOsdetail
Command Mode: exec : Exec Mode
Command Path:
# show vlan-domain [name <>] [vlan] [leaf <>] [detail]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1229
S Commandsshow vlan-domain
show vmware domainshow vmware domain
Description: Show VMware domain information
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1230
S Commandsshow vmware domain
show vmware domain nameshow vmware domain name <name>
Description: VMware domain name
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1231
S Commandsshow vmware domain name
show vmware domain name epgshow vmware domain name <name> epg
Description: Show VMware domain EPG details
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> epg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1232
S Commandsshow vmware domain name epg
show vmware domain name esxshow vmware domain name <name> esx <esx-ip>
Description: Show VMware ESX information
Syntax:
VMware domain name<name>
ESX IP<esx-ip>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> esx <esx-ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1233
S Commandsshow vmware domain name esx
show vmware domain name port-groupshow vmware domain name <name> port-group
Description: Show VMware port group information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> port-group
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1234
S Commandsshow vmware domain name port-group
show vmware domain name vcentershow vmware domain name <name> vcenter <hostname|ip>
Description: VMware vCenter ip or hostname
Syntax:
VMware domain name<name>
vCenter hostname or IP<hostname|ip>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vcenter <hostname|ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1235
S Commandsshow vmware domain name vcenter
show vmware domain name vmshow vmware domain name <name> vm
Description: Show VMware VM information
Syntax:
VMware domain name<name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vm
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1236
S Commandsshow vmware domain name vm
show vmware domain name vm nameshow vmware domain name <name> vm name <vm-name>
Description: Show detailed VMware VM information
Syntax:
VMware domain name<name>
VM Name<vm-name>
Command Mode: exec : Exec Mode
Command Path:
# show vmware domain name <name> vm name <vm-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1237
S Commandsshow vmware domain name vm name
show vmware vmshow vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Description: Show VMware VM information
Syntax:
(Optional) Specify a VM nameWORD
(Optional) IP address in format i.i.i.iA.B.C.D
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: exec : Exec Mode
Command Path:
# show vmware vm [name <WORD>] [ip <A.B.C.D>] [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1238
S Commandsshow vmware vm
show vpcshow vpc map <vpc-list>
Description: show vpc mapping
Syntax:
map by namemap
vpc names<vpc-list>
Command Mode: exec : Exec Mode
Command Path:
# show vpc map <vpc-list>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1239
S Commandsshow vpc
show vpc map leafshow vpc map <vpc-list> leaf WORD [fex <NUMBER>]
Description: leaf
Syntax:
map by namemap
vpc names<vpc-list>
Leaf Range or Leaf Name ListWORD
(Optional) Fex ID. Number range from=101 to=164<101-164>
Command Mode: exec : Exec Mode
Command Path:
# show vpc map <vpc-list> leaf WORD [fex <NUMBER>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1240
S Commandsshow vpc map leaf
show vrfshow vrf WORD
Description: Show VRF Information
Syntax:
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show vrf WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1241
S Commandsshow vrf
show vrf detailshow vrf WORD detail
Description: Show detailed view of VRF
Syntax:
Name of the VRF to filter on (Max Size 64)WORD
Command Mode: exec : Exec Mode
Command Path:
# show vrf WORD detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1242
S Commandsshow vrf detail
shutshut
Description: Disable BFD
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>(config-template-bfd-pol)# shut
shut
Description: Disable monitor session
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# shut
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1243
S Commandsshut
shutdownshutdown
Description: Administrative state of the Policer
Command Mode: policy-map : Create a policymap of DataPlane type to police/reclassify the traffic
Command Path:
# configure [['terminal', 't']](config)# policy-map type data-plane <WORD>(config-pmap-dpp)# shutdown
shutdown
Description: Disable the class of service specified
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']](config)# qos parameters level1|level2|level3(config-qos)# shutdown
shutdown
Description: Administrative state of the Policer
Command Mode: policy-map type data-plane : data-plane policy type
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# policy-map type data-plane <WORD>(config-tenant-pmap-dpp)# shutdown
shutdown
Description: Disable Interface
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# shutdown
shutdown
Description: Disable Port Channel
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1244
S Commandsshutdown
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# shutdown
shutdown
Description: Disable interface
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# shutdown
shutdown
Description: Disable monitor session
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# shutdown
shutdown
Description: Disable monitor session
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# shutdown
shutdown
Description: Disable monitor session
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# shutdown
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1245
S Commandsshutdown
site-idsite-id <WORD>
Description: ID of the network where the site is deployed
Syntax:
The site id (Max Size 512) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# site-id <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1246
S Commandssite-id
slow-timerslow-timer <NUMBER>
Description: Configure BFD SLOW-TIMER value in milliseconds
Syntax:
BFD interval. Number range from=1000 to=30000<interval>
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>(config-bfd)# slow-timer <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1247
S Commandsslow-timer
snapshot downloadsnapshot download <WORD>
Description: Configuration snapshot download setup mode
Syntax:
Snapshot downloader nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot download <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1248
S Commandssnapshot download
snapshot exportsnapshot export <WORD>
Description: Configuration export setup mode
Syntax:
Export configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1249
S Commandssnapshot export
snapshot importsnapshot import <WORD>
Description: Configuration import setup mode
Syntax:
Import configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot import <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1250
S Commandssnapshot import
snapshot rollbacksnapshot rollback <WORD>
Description: Configuration rollback setup mode
Syntax:
Rollback configuration nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot rollback <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1251
S Commandssnapshot rollback
snapshot uploadsnapshot upload <WORD>
Description: Configuration snapshot upload setup mode
Syntax:
Snapshot uploader nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# snapshot upload <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1252
S Commandssnapshot upload
snmp-server clientgroupsnmp-server clientgroup <group-name> [management-epg <mgmt-epg>] [client <ip-address/hostname>]
Description: Configure SNMP client-group
Syntax:
SNMP clientgroup<group-name>
(Optional) Management EPG (default: oob-default)<mgmt-epg>
(Optional) Ip-address/hostname of the snmp client<ip-address/hostname>
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server clientgroup <group-name> [management-epg <mgmt-epg>] [client<ip-address/hostname>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1253
S Commandssnmp-server clientgroup
snmp-server communitysnmp-server community <community-name>
Description: Configure SNMP community
Syntax:
SNMP community<community-name>
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server community <community-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1254
S Commandssnmp-server community
snmp-server contactsnmp-server contact <contact-name>
Description: Configure SNMP contact
Syntax:
SNMP contact name<contact-name>
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server contact <contact-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1255
S Commandssnmp-server contact
snmp-server hostsnmp-server host <ip-address/hostname> traps-version 1|2c|3 <community> auth|none|priv [udp-port <port>][management-epg <mgmt-epg>]
Description: Configure SNMP trap host
Syntax:
Ip-address/hostname of the snmp trap destination<ip-address/hostname>
SNMP Version to use for trapstraps-version
Use SNMPv11
Use SNMPv22c
Use SNMPv33
SNMP community/security<community>
Use Authentication Onlyauth
Use No Authenticationnone
Use Authentication and Encryptionpriv
(Optional) UDP port for traps (default 162)<port>
(Optional) Management EPG (default: oob-default)<mgmt-epg>
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server host <ip-address/hostname> traps-version 1|2c|3 <community>auth|none|priv [udp-port <port>] [management-epg <mgmt-epg>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1256
S Commandssnmp-server host
snmp-server locationsnmp-server location <location-name>
Description: Configure SNMP location
Syntax:
SNMP location<location-name>
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server location <location-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1257
S Commandssnmp-server location
snmp-server protocolsnmp-server protocol enable
Description: Enable SNMP protocol
Syntax:
Enable SNMP protocolenable
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server protocol enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1258
S Commandssnmp-server protocol
snmp-server usersnmp-server user <user-name> auth sha|md5 <auth-key> priv aes|des|none [privacy-passphrase <priv-key>]
Description: Configure SNMP user
Syntax:
SNMP user<user-name>
Authentication Typeauth
Use HMAC SHA algorithm for authenticationsha
Use HMAC MD5 algorithm for authenticationmd5
Authentication password for user (Min Size 8, Max Size 130)<auth-key>
Privacy Typepriv
Use 128-bit AES algorithm for privacyaes
Use 64-bit DES algorithm for privacydes
Do not use privacynone
(Optional) Privacy passphrase for user (Min Size 8, Max Size 130)<priv-key>
Command Mode: pod : Pod configuration mode
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# snmp-server user <user-name> auth sha|md5 <auth-key> priv aes|des|none[privacy-passphrase <priv-key>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1259
S Commandssnmp-server user
sourcesource tenant <WORD> application <WORD> epg <WORD> [mac <E.E.E EE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE >]
Description: Configure monitor virtual source
Syntax:
tenanttenant
tenant name (Max Size 63)WORD
applicationapplication
application name (Max Size 64)WORD
epgepg
epg name (Max Size 64)WORD
(Optional) MAC address (Option 1) MAC address (Option 2) MACaddress (Option 3) MAC address (Option 4)
E.E.E EE-EE-EE-EE-EE-EEEE:EE:EE:EE:EE:EEEEEE.EEEE.EEEE
Command Mode: monitor virtual : Configure monitor session for virtual switches
Command Path:
# configure [['terminal', 't']](config)# monitor virtual session <WORD>(config-monitor-virtual)# source tenant <WORD> application <WORD> epg <WORD> [mac <E.E.EEE-EE-EE-EE-EE-EE EE:EE:EE:EE:EE:EE EEEE.EEEE.EEEE >]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1260
S Commandssource
source applicationsource application <application_name> epg <epg_name>
Description: Configure EPG as monitor source
Syntax:
application name (Max Size 64)application_name
epgepg
epg name (Max Size 64)epg_name
Command Mode: monitor tenant : Configue monitor session for tenant EPGs
Command Path:
# configure [['terminal', 't']](config)# monitor tenant <tenant_name> session <session_name>(config-monitor-tenant)# source application <application_name> epg <epg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1261
S Commandssource application
source interface ethernetsource interface ethernet <ethernet> leaf <leaf Id>
Description: Configure monitor for ethernet access interfaces
Syntax:
List of ethernet itfs<ethernet>
leafleaf
leaf Id<leaf Id>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface ethernet <ethernet> leaf <leaf Id>
source interface ethernet <ethernet> switch <switch Id>
Description: Configure monitor for ethernet fabric interfaces
Syntax:
ethernet interface range<ethernet>
switchswitch
switch Id<switch Id>
Command Mode: monitor fabric : Configue monitor session for fabric interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor fabric session <session_name>(config-monitor-fabric)# source interface ethernet <ethernet> switch <switch Id>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1262
S Commandssource interface ethernet
source interface port-channelsource interface port-channel <port-channel list> leaf <leaf Id> [fex <fex Id>]
Description: Configure monitor for port-channel interfaces
Syntax:
<port-channel list><port-channel list>
leafleaf
leaf Id<leaf Id>
(Optional) fex Id<fex Id>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface port-channel <port-channel list> leaf <leaf Id>[fex <fex Id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1263
S Commandssource interface port-channel
source interface vpcsource interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex <fex Ids>]
Description: Configure monitor for VPC interfaces
Syntax:
<vpc list><vpc list>
leafleaf
leaf Id1<leaf Id1>
leaf Id2<leaf Id2>
(Optional) paired fex Ids<fex Ids>
Command Mode: monitor access : Configue monitor session for access interfaces
Command Path:
# configure [['terminal', 't']](config)# monitor access session <session_name>(config-monitor-access)# source interface vpc <vpc list> leaf <leaf Id1> <leaf Id2> [fex<fex Ids>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1264
S Commandssource interface vpc
spanning-treespanning-tree mst configuration
Description: STP MST configuration mode
Syntax:
Multiple spanning treemst
Configure multiple spanning tree protocolconfiguration
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# spanning-tree mst configuration
spanning-tree
Description: Add spanning tree
Command Mode: template leaf-policy-group : Configure Leaf Policy Group
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>(config-leaf-policy-group)# spanning-tree
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable or Disable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1265
S Commandsspanning-tree
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: enable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Enable or disable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: enable BPDU filter/guard
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1266
S Commandsspanning-tree
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Description: Spanning Tree Subsystem
Syntax:
Don't send or receive BPDUs on this interfacebpdu-filter
Don't accept BPDUs on this interfacebpdu-guard
enable/disable BPDU filter/guard<enable|disable>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# spanning-tree bpdu-filter|bpdu-guard <enable|disable>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1267
S Commandsspanning-tree
spanning-tree bpdu-filterspanning-tree bpdu-filter enable|disable|default
Description: Configure BPDU filter override on AVS uplink ports
Syntax:
Enable BPDU filterenable
Disable BPDU filterdisable
Remove BPDU filter/guard override policydefault
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# spanning-tree bpdu-filter enable|disable|default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1268
S Commandsspanning-tree bpdu-filter
spanning-tree bpdu-guardspanning-tree bpdu-guard enable|disable|default
Description: Configure BPDU guard override on AVS uplink ports
Syntax:
Enable BPDU guardenable
Disable BPDU guarddisable
Remove BPDU filter/guard override policydefault
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# spanning-tree bpdu-guard enable|disable|default
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1269
S Commandsspanning-tree bpdu-guard
speedspeed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<interfaceSpeed>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# speed <interfaceSpeed>
speed <portChannelSpeed>
Description: Configure Interface Speed
Syntax:
Port-Channel Speed Policy<portChannelSpeed>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# speed <portChannelSpeed>
speed <interfaceSpeed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<interfaceSpeed>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# speed <interfaceSpeed>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1270
S Commandsspeed
speed <speed>
Description: Configure Interface Speed
Syntax:
Speed Value<speed>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# speed <speed>
speed <speed>
Description: Configure Interface Speed
Syntax:
Interface Speed Policy<speed>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# speed <speed>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1271
S Commandsspeed
spf-intervalspf-interval level-1 <NUMBER> <50-120000> <50-120000>
Description: Set the ISIS SPF maximal wait interval
Syntax:
Level 1level-1
SPF maximum wait interval. Number range from=50 to=120000<50-120000>
Initial and secondary wait intervals (both values are required)<50-120000> <50-120000>
Command Mode: isis : Intermediate System to Intermediate System (IS-IS)
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# isis fabric(config-pod-isis)# spf-interval level-1 <NUMBER> <50-120000> <50-120000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1272
S Commandsspf-interval
ssh-keyssh-key <WORD>
Description: Update ssh key for the user for ssh authentication
Syntax:
A name for SSH key (Max Size 64)WORD
Command Mode: username : Create a locally-authenticated user account
Command Path:
# configure [['terminal', 't']](config)# username <WORD>(config-username)# ssh-key <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1273
S Commandsssh-key
ssh-servicessh-service
Description: SSH communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# ssh-service
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1274
S Commandsssh-service
ssl-protocolsssl-protocols <sslProtocols>
Description: Set the SSL protocol (comma separated values)
Syntax:
SSL Protocols as comma separated values like val1,val2,..valNsslProtocols
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ssl-protocols <sslProtocols>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1275
S Commandsssl-protocols
ssl-validation-levelssl-validation-level <ssl-validation-level>
Description: Set the LDAP Server SSL Certificate validation level
Syntax:
<ssl-validation-level><ssl-validation-level>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# ssl-validation-level <ssl-validation-level>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1276
S Commandsssl-validation-level
statestate <WORD>
Description: Set The state or province in which the organization is located.
Syntax:
state or province (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# state <WORD>
state <cipherState>
Description: Cipher state
Syntax:
Cipher state as comma separated values like val1,val2,..valNcipherState
Command Mode: ciphers : HTTPS cipher suite
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# ciphers <WORD>(config-ciphers)# state <cipherState>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1277
S Commandsstate
static-endpointstatic-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure Silent Host behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1278
S Commandsstatic-endpoint
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> [ip<A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Description: Configure silent Host behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
(Optional) List of IP addresses in format i.i.i.iA1.B1.C1.D1,...,An.Bn.Cn.Dn
(Optional) List of IPv6 address in format xxxx:xxxx, xxxx::xxA1:B1::C1:D1,..,An:Bn::Cn:Dn
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1279
S Commandsstatic-endpoint
(config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# static-endpoint mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> [ip <A1.B1.C1.D1,...,An.Bn.Cn.Dn>] [ipv6 <A1:B1::C1:D1,..,An:Bn::Cn:Dn>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1280
S Commandsstatic-endpoint
static-tepstatic-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1281
S Commandsstatic-tep
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE vlan <NUMBER> <A.B.C.D>
Description: Configure a static Tunnel Endpoint behind a EPG with a Static Path Attachment
Syntax:
MAC addressmac
MAC address (Option 1)E.E.E
MAC address (Option 2)EE-EE-EE-EE-EE-EE
MAC address (Option 3)EE:EE:EE:EE:EE:EE
MAC address (Option 4)EEEE.EEEE.EEEE
Encapsulation Vlanvlan
VLAN range. Number range from=1 to=4094<1-4094>
IP address in format i.i.i.iA.B.C.D
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# static-tep mac E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEEvlan <NUMBER> <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1282
S Commandsstatic-tep
statisticsstatistics enable
Description: Enable/disable stats collection on VCenter (DVS-only)
Syntax:
enableenable
Command Mode: vcenter : Configure a VCenter in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# statistics enable
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1283
S Commandsstatistics
storm-control levelstorm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1284
S Commandsstorm-control level
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control level <0-100> [burst-rate <0-100>]
storm-control level <0-100> [burst-rate <0-100>]
Description: Configure Storm Control Level (bandwidth percentage) on the Interface
Syntax:
Rate of Bandwidth in Percentage<0-100>
(Optional) Max Rate of Bandwidth in Percentage<0-100>
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control level <0-100> [burst-rate <0-100>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1285
S Commandsstorm-control level
storm-control ppsstorm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1286
S Commandsstorm-control pps
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# storm-control pps <> burst-rate <>
storm-control pps <arg> burst-rate <arg>
Description: Configure Storm Control in packet per second on the Interface
Syntax:
Burst Rate in packets per second. Number range from=0 to=4882812arg
Max Burst Rate in packets per secondburst-rate
Max Burst Rate in packets per second. Number range from=0to=4882812
arg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1287
S Commandsstorm-control pps
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# storm-control pps <> burst-rate <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1288
S Commandsstorm-control pps
street-addressstreet-address <WORD>
Description: Street address of the site
Syntax:
The street address (Max Size 255) surrounded by quotesWORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# street-address <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1289
S Commandsstreet-address
subjectsubject <WORD>
Description: Set The fully qualified domain name or DN of the requesting device.
Syntax:
FQDN or DN of device (Max Size 64)<WORD>
Command Mode: csr : A csr mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# csr(config-csr)# subject <WORD>
subject <WORD>
Description: Configuration a subject on the contract
Syntax:
Name of the contract subject (Max Size 64)WORD
Command Mode: contract : Configure binary contracts between Application EPGs
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# contract <WORD> [type <type>](config-tenant-contract)# subject <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1290
S Commandssubject
summary-addresssummary-address <IP-PREFIX/LEN>
Description: Route summarization
Syntax:
Summarized ipIP-PREFIX/LEN
Command Mode: vrf : Associate Router OSPF Policy with Tenant/VRF
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>(config-leaf-ospf-vrf)# summary-address <IP-PREFIX/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1291
S Commandssummary-address
switch-groupswitch-group <WORD>
Description: Create switch firmware upgrade policy
Syntax:
switch-group name (Max Size 64)WORD
Command Mode: firmware : Firmware upgrade configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1292
S Commandsswitch-group
switchswitch
Description: Add switches to switch group
Syntax:
arg
Command Mode: switch-group : Create switch firmware upgrade policy
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# switch-group <WORD>(config-firmware-switch)# switch
switch
Description: Configure Leaf Node
Syntax:
arg
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# switch
switch
Description: Add switches to zone
Syntax:
arg
Command Mode: zone : Create zone policy
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>(config-zone)# switch
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1293
S Commandsswitch
switchingswitching mode vlan|vxlan|vxlan-ns
Description: Configure switching mode.
Syntax:
switching Modemode
VLAN/SW Modevlan
VXLAN/SW Modevxlan
VXLAN/HWModevxlan-ns
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# switching mode vlan|vxlan|vxlan-ns
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1294
S Commandsswitching
switchportswitchport vlan scope local
Description: L2 configuration
Syntax:
vlan
scope
Local Scopelocal
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# switchport vlan scope local
switchport vlan scope local
Description: L2 configuration
Syntax:
vlan
scope
Local Scopelocal
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# switchport vlan scope local
switchport
Description: Configure switchport parameters
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1295
S Commandsswitchport
(config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport
switchport
Description: Configure switchport parameters
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport
switchport
Description: Configure switchport parameters
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1296
S Commandsswitchport
switchport access vlan tenant applicationswitchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1297
S Commandsswitchport access vlan tenant application
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application Name
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1298
S Commandsswitchport access vlan tenant application
switchport access vlan tenant external-sviswitchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Access Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1299
S Commandsswitchport access vlan tenant external-svi
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Acess L2 Interface
Syntax:
Access Vlanvlan
Access Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport access vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1300
S Commandsswitchport access vlan tenant external-svi
switchport trunk allowed vlan inband-mgmtswitchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
Description: Configure External L2 connectivity to inband Mnaagement
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Gateway IP Address for External Connectivity format x.x.x.x/mA.B.C.D/LEN
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> inband-mgmt <A.B.C.D/LEN>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1301
S Commandsswitchport trunk allowed vlan inband-mgmt
switchport trunk allowed vlan tenant applicationswitchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD> [primary-vlanprimary-vlan <evlan>]
Description: Add an AEPg as static encap
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
(Optional) Vlan for egress traffic when EPG isolation is enforcedprimary-vlan <evlan>
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD> [primary-vlan primary-vlan <evlan>]
switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Add an AEPg as static encap
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1302
S Commandsswitchport trunk allowed vlan tenant application
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>
switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Add an AEPg as static encap
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1303
S Commandsswitchport trunk allowed vlan tenant application
switchport trunk allowed vlan tenant external-l2switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Description: Add a L2 external EPG on the interface
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
L2 external EPG nameepg
L2 external EPG name (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg<WORD>
switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Description: Add a L2 external EPG on the interface
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
L2 external EPG nameepg
L2 external EPG name (Max Size 64)WORD
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1304
S Commandsswitchport trunk allowed vlan tenant external-l2
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg<WORD>
switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Description: Add a L2 external EPG on the interface
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
L2 external EPG nameepg
L2 external EPG name (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-l2 epg <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1305
S Commandsswitchport trunk allowed vlan tenant external-l2
switchport trunk allowed vlan tenant external-sviswitchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Interface
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD
switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Interface
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1306
S Commandsswitchport trunk allowed vlan tenant external-svi
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD
switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Interface
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1307
S Commandsswitchport trunk allowed vlan tenant external-svi
switchport trunk allowed vlan tenant legacy-forwardingswitchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Description: Add legacy forwarding on the vlan supplied
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPg (Max Size 63)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Description: Add legacy forwarding on the vlan supplied
Syntax:
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Description: Add legacy forwarding on the vlan supplied
Syntax:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1308
S Commandsswitchport trunk allowed vlan tenant legacy-forwarding
Encapsulation Vlanvlan
Encapsulation Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the EPgtenant
Tenant hosting the EPg (Max Size 63)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk allowed vlan <NUMBER> tenant <WORD> legacy-forwarding
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1309
S Commandsswitchport trunk allowed vlan tenant legacy-forwarding
switchport trunk native vlan tenant applicationswitchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the AEPg
Syntax:
Native Vlanvlan
Native Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>
switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the AEPg
Syntax:
Native Vlanvlan
Native Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1310
S Commandsswitchport trunk native vlan tenant application
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD>epg <WORD>
switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg <WORD>
Description: Application hosting the AEPg
Syntax:
Native Vlanvlan
Native Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
Application Name (Max Size 64)WORD
EPg that uses the statically enabled Encapepg
EPg that uses the statically enabled Encap (Max Size 64)WORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk native vlan <NUMBER> tenant <WORD> application <WORD> epg<WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1311
S Commandsswitchport trunk native vlan tenant application
switchport trunk native vlan tenant external-sviswitchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to the L2 Trunk Interface
Syntax:
Native Vlanvlan
Native Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD
switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate Native Vlan to the L2 Trunk Interface as external SVI
Syntax:
Native Vlanvlan
Native Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface port-channel : Port Channel interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1312
S Commandsswitchport trunk native vlan tenant external-svi
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD
switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out] WORD
Description: Associate SVI to Trunk L2 Interface
Syntax:
Native Vlanvlan
Native Vlan. Number range from=1 to=4094<1-4094>
Tenant hosting the AEPgtenant
Tenant hosting the AEPg (Max Size 63)WORD
(Optional) Specify one or more l3extOut to add SVI interfacel3out
l3extOut NameWORD
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport trunk native vlan <NUMBER> tenant <WORD> external-svi [l3out]WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1313
S Commandsswitchport trunk native vlan tenant external-svi
switchport vlanswitchport vlan scope local
Description: L2 configuration
Syntax:
scope
Local Scopelocal
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# switchport vlan scope local
switchport vlan scope local
Description:
Syntax:
scope
Local Scopelocal
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# switchport vlan scope local
switchport vlan scope local
Description:
Syntax:
scope
Local Scopelocal
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1314
S Commandsswitchport vlan
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# switchport vlan scope local
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1315
S Commandsswitchport vlan
syslogsyslog common
Description: Syslog common policy configuration mode
Syntax:
Syslog common policy configuration modecommon
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# syslog common
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1316
S Commandssyslog
system cluster-sizesystem cluster-size <NUMBER>
Description: Set APIC cluster size
Syntax:
size of the cluster to be set. Number range from=1 to=16<size>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# system cluster-size <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1317
S Commandssystem cluster-size
system controller-idsystem controller-id <serial-number> approve|reject
Description: Configure Controller Id for controllers in fabric
Syntax:
Controller serial numberserial-number
Approve controllerapprove
Reject controllerreject
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# system controller-id <serial-number> approve|reject
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1318
S Commandssystem controller-id
system dynamic-load-balancesystem dynamic-load-balance modelink-failure-resiliency|dynamic-aggressive|dynamic-conservative|packet-prioritization
Description: Configure dynamic load balancer
Syntax:
Dynamic load balancer modemode
Link failure resiliency modelink-failure-resiliency
Aggressive dynamic modedynamic-aggressive
Conservative dynamic modedynamic-conservative
Packet prioritization modepacket-prioritization
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# system dynamic-load-balance modelink-failure-resiliency|dynamic-aggressive|dynamic-conservative|packet-prioritization
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1319
S Commandssystem dynamic-load-balance
system fabric-security-modesystem fabric-security-mode <mode>
Description: Set strict/permissive mode for ACI Fabric Internode Authentication
Syntax:
Security mode as comma separated values like val1,val2,..valN<mode>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# system fabric-security-mode <mode>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1320
S Commandssystem fabric-security-mode
system jumbomtusystem jumbomtu <NUMBER>
Description:MTU size for Host Facing ports
Syntax:
Enter jumbomtu. Number range from=576 to=9000<576-9000>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# system jumbomtu <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1321
S Commandssystem jumbomtu
system switch-idsystem switch-id <serial-number> <node-Id> <name>
Description: Configure Node Id for switches in fabric
Syntax:
Switch serial numberserial-number
Switch ID. Number range from=101 to=4000node-Id
Switch namename
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# system switch-id <serial-number> <node-Id> <name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1322
S Commandssystem switch-id
T Commands
• tacacs-server host, page 1327
• tacacs-server retries, page 1328
• tacacs-server timeout, page 1329
• tag, page 1330
• target, page 1332
• telnet, page 1333
• template bfd, page 1334
• template bgp address-family, page 1335
• template bgp timers, page 1336
• template community-list expanded, page 1337
• template community-list standard, page 1338
• template dhcp option, page 1339
• template dhcp relay, page 1340
• template eigrp interface-policy, page 1341
• template eigrp vrf-policy, page 1342
• template endpoint retention policy, page 1343
• template extcommunity-list expanded, page 1344
• template extcommunity-list standard, page 1345
• template ip igmp snooping policy, page 1346
• template ipv6 nd policy, page 1347
• template ipv6 nd prefix, page 1348
• template leaf-policy-group, page 1349
• template ospf interface-policy, page 1350
• template ospf vrf-policy, page 1351
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1323
• template policy-group, page 1352
• template port-channel, page 1353
• template route-profile, page 1354
• template route tag, page 1355
• tenant, page 1356
• terminal, page 1357
• time, page 1358
• time start daily, page 1359
• time start weekly, page 1360
• timeout, page 1361
• timers, page 1362
• timers lsa-arrival, page 1364
• timers lsa-group-pacing, page 1365
• timers throttle lsa, page 1366
• timers throttle spf, page 1367
• tp, page 1368
• transmit-delay, page 1369
• transport email from, page 1370
• transport email mail-server, page 1371
• transport email reply-to, page 1372
• trigger fabric-recovery, page 1373
• trigger shutdown, page 1374
• trigger snapshot download, page 1375
• trigger snapshot export, page 1376
• trigger snapshot import, page 1377
• trigger snapshot rollback, page 1378
• trigger snapshot upload, page 1379
• trigger techsupport all, page 1380
• trigger techsupport controllers, page 1381
• trigger techsupport host, page 1382
• trigger techsupport local, page 1383
• trigger techsupport switch, page 1384
• trigger troubleshoot epext session report, page 1385
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1324
T Commands
• trigger troubleshoot eptoep session report, page 1386
• trigger vmware, page 1387
• troubleshoot epext session atomiccounter, page 1388
• troubleshoot epext session description, page 1389
• troubleshoot epext session latestminutes, page 1390
• troubleshoot epext session monitor destination apic, page 1391
• troubleshoot epext session monitor destination prefdestgroup, page 1392
• troubleshoot epext session monitor destination tenant, page 1393
• troubleshoot epext session scheduler, page 1395
• troubleshoot epext session srcextip destip tenant application, page 1396
• troubleshoot epext session srcextip destip tenant vrf, page 1397
• troubleshoot epext session srcip tenant application epg destextip, page 1398
• troubleshoot epext session srcip tenant vrf destextip, page 1399
• troubleshoot epext session starttime, page 1400
• troubleshoot epext session traceroute, page 1401
• troubleshoot epext session traceroute protocol icmp, page 1402
• troubleshoot epext session traceroute protocol tcp, page 1403
• troubleshoot epext session traceroute protocol udp, page 1404
• troubleshoot eptoep session atomiccounter, page 1405
• troubleshoot eptoep session description, page 1406
• troubleshoot eptoep session latestminutes, page 1407
• troubleshoot eptoep session monitor destination apic, page 1408
• troubleshoot eptoep session monitor destination prefdestgroup, page 1409
• troubleshoot eptoep session monitor destination tenant, page 1410
• troubleshoot eptoep session scheduler, page 1412
• troubleshoot eptoep session srcip tenant application epg destip tenant application, page 1413
• troubleshoot eptoep session srcip tenant application epg destip tenant vrf, page 1414
• troubleshoot eptoep session srcip tenant vrf destip tenant application, page 1415
• troubleshoot eptoep session srcip tenant vrf destip tenant vrf, page 1416
• troubleshoot eptoep session srcmac tenant application epg destmac tenant application, page 1417
• troubleshoot eptoep session srcmac tenant application epg destmac tenant vrf, page 1419
• troubleshoot eptoep session srcmac tenant vrf destmac tenant application, page 1420
• troubleshoot eptoep session srcmac tenant vrf destmac tenant vrf, page 1421
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1325
T Commands
• troubleshoot eptoep session starttime, page 1422
• troubleshoot eptoep session traceroute, page 1423
• troubleshoot eptoep session traceroute protocol icmp, page 1424
• troubleshoot eptoep session traceroute protocol tcp, page 1425
• troubleshoot eptoep session traceroute protocol udp, page 1426
• trusted-key, page 1427
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1326
T Commands
tacacs-server hosttacacs-server host <A.B.C.D|A:B::C:D|WORD>
Description: TACACS+ server's DNS name or its IP address
Syntax:
TACACS+ server's DNS name or its IP addressA.B.C.D|A:B::C:D|WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1327
T Commandstacacs-server host
tacacs-server retriestacacs-server retries <NUMBER>
Description: Global TACACS+ server retries period in seconds
Syntax:
Global TACACS+ server retries period in seconds. Number rangefrom=0 to=5
<0-5>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# tacacs-server retries <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1328
T Commandstacacs-server retries
tacacs-server timeouttacacs-server timeout <NUMBER>
Description: Global TACACS+ server timeout period in seconds
Syntax:
Global TACACS+ server timeout period in seconds. Number rangefrom=1 to=60
<1-60>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# tacacs-server timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1329
T Commandstacacs-server timeout
tagtag <WORD>
Description: Add a tag to an epg
Syntax:
Tag for the object (Max Size 64)WORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# tag <WORD>
tag <WORD>
Description: Add a tag to an application
Syntax:
Tag for the object (Max Size 64)WORD
Command Mode: application : application configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# tag <WORD>
tag <WORD>
Description: Add a tag to the tenant
Syntax:
Tag for the object (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1330
T Commandstag
(config-tenant)# tag <WORD>
tag <NUMBER>
Description: Set Route Tag
Syntax:
Route Tag Value. Number range from=0 to=4294967295<0-4294967295>
Command Mode: template route tag : Configure Route Tag Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route tag <WORD> tenant <WORD>(config-route-tag)# tag <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1331
T Commandstag
targettarget self|children|subtree
Description: Configure target dn/class
Syntax:
Selfself
Childrenchildren
Subtreesubtree
Command Mode: query : Configure Query profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# query-profile(config-callhome-queryprof)# query <WORD> type dn|class <dn/classname>(config-callhome-queryprof-query)# target self|children|subtree
target <WORD>
Description: Snapshot target
Syntax:
infra, fabric or tenant-xWORD
Command Mode: snapshot export : Configuration export setup mode
Command Path:
# configure [['terminal', 't']](config)# snapshot export <WORD>(config-export)# target <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1332
T Commandstarget
telnettelnet
Description: TELNET communication policy group
Command Mode: comm-policy : Configure any communication policy, ssh/telnet/shellinabox/http/https
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# telnet
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1333
T Commandstelnet
template bfdtemplate bfd ip|ipv6 <WORD>
Description: BFD group of commands
Syntax:
IPV4 Addressip
IPV6 Addressipv6
Create a BFD policyWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# template bfd ip|ipv6 <WORD>
template bfd <WORD> tenant <WORD>
Description: Configure BFD Interface Policy Templates
Syntax:
BFD Interface Policy name (Max Size 64)WORD
Tenant for the BFD Policytenant
Tenant name (Max Size 63)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bfd <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1334
T Commandstemplate bfd
template bgp address-familytemplate bgp address-family <WORD> tenant <WORD>
Description: Configure Router BGP Address Family Templates
Syntax:
BGP Address Family Policy Name (Max Size 64)WORD
Tenant for the BGP Policytenant
Tenant NameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp address-family <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1335
T Commandstemplate bgp address-family
template bgp timerstemplate bgp timers <WORD> tenant <WORD>
Description: Configure Router BGP Timer Policy Templates
Syntax:
Router BGP Timer Policy Name (Max Size 64)WORD
Tenant for the BGP Policytenant
Tenant Name (Max Size 63)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1336
T Commandstemplate bgp timers
template community-list expandedtemplate community-list expanded <WORD> <regular expression> tenant <WORD>
Description: Configure expanded community list templates
Syntax:
community name (Max Size 64)WORD
community regular expression<regular expression>
Tenant for the VRFtenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template community-list expanded <WORD> <regular expression> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1337
T Commandstemplate community-list expanded
template community-list standardtemplate community-list standard <WORD> <community list> tenant <WORD>
Description: Configure standard community list templates
Syntax:
community name (Max Size 64)WORD
<community list><community list>
Tenant for the VRFtenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template community-list standard <WORD> <community list> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1338
T Commandstemplate community-list standard
template dhcp optiontemplate dhcp option policy <WORD>
Description: Create a DHCP Option policy
Syntax:
Name of the DHCP Option Policypolicy
Name of the DHCP Option Policy (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp option policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1339
T Commandstemplate dhcp option
template dhcp relaytemplate dhcp relay policy <WORD>
Description: Create a DHCP Relay policy
Syntax:
Name of the DHCP relay policypolicy
Name of the DHCP relay policy (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# template dhcp relay policy <WORD>
template dhcp relay policy <WORD>
Description: Create a DHCP Relay policy
Syntax:
Name of the DHCP relay policypolicy
Name of the DHCP relay policy (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template dhcp relay policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1340
T Commandstemplate dhcp relay
template eigrp interface-policytemplate eigrp interface-policy <WORD> tenant <WORD>
Description: Configure EIGRP Interface policy templates
Syntax:
Policy name (Max Size 64)WORD
Tenant for the EIGRP Interface Policytenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp interface-policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1341
T Commandstemplate eigrp interface-policy
template eigrp vrf-policytemplate eigrp vrf-policy <WORD> tenant <WORD>
Description: Configure EIGRP VRF policy templates
Syntax:
Policy name (Max Size 64)WORD
Tenant for the EIGRP VRF Policytenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1342
T Commandstemplate eigrp vrf-policy
template endpoint retention policytemplate endpoint retention policy <WORD>
Description: Configure an endpoint retention policy
Syntax:
Name of the endpoint retention policy to set (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template endpoint retention policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1343
T Commandstemplate endpoint retention policy
template extcommunity-list expandedtemplate extcommunity-list expanded <WORD> <regular expression> tenant <WORD>
Description: Configure expanded community list templates
Syntax:
community name (Max Size 64)WORD
community regular expression<regular expression>
Tenant for the VRFtenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template extcommunity-list expanded <WORD> <regular expression> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1344
T Commandstemplate extcommunity-list expanded
template extcommunity-list standardtemplate extcommunity-list standard <WORD> [scope <scope>] <community list> tenant <WORD>
Description: Configure standard community list templates
Syntax:
community name (Max Size 64)WORD
(Optional) transitive or non-transitivescope
<community list><community list>
Tenant for the VRFtenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template extcommunity-list standard <WORD> [scope <scope>] <community list>tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1345
T Commandstemplate extcommunity-list standard
template ip igmp snooping policytemplate ip igmp snooping policy <WORD>
Description: Create an IGMP snooping policy
Syntax:
Name of the IGMP snooping policy to define (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ip igmp snooping policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1346
T Commandstemplate ip igmp snooping policy
template ipv6 nd policytemplate ipv6 nd policy <WORD>
Description: Create/modify an an IPv6 Neighbor Discovery policy
Syntax:
Name of the policy to create/modify (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd policy <WORD>
template ipv6 nd policy <WORD> tenant <WORD>
Description: Configure IPv6 Neighbor Discovery policy templates
Syntax:
Policy name (Max Size 64)WORD
Tenant for the ND Policytenant
Tenant nameWORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ipv6 nd policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1347
T Commandstemplate ipv6 nd policy
template ipv6 nd prefixtemplate ipv6 nd prefix policy <WORD>
Description: Create/modify an an IPv6 Neighbor Prefix policy
Syntax:
IPv6 ND Prefix Policypolicy
Name of the policy to create/modify (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# template ipv6 nd prefix policy <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1348
T Commandstemplate ipv6 nd prefix
template leaf-policy-grouptemplate leaf-policy-group <WORD>
Description: Configure Leaf Policy Group
Syntax:
Leaf Policy Group NameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# template leaf-policy-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1349
T Commandstemplate leaf-policy-group
template ospf interface-policytemplate ospf interface-policy <WORD> tenant <WORD>
Description: Configure OSPF Interface Policy Templates
Syntax:
OSPF Interface Policy name (Max Size 64)WORD
Tenant for the OSPF Policytenant
Tenant name (Max Size 63)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1350
T Commandstemplate ospf interface-policy
template ospf vrf-policytemplate ospf vrf-policy <WORD> tenant <WORD>
Description: Configure Router OSPF Timer Policy Templates
Syntax:
Router OSPF Timer Policy name (Max Size 64)WORD
Tenant for the OSPF Policytenant
Tenant name (Max Size 63)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1351
T Commandstemplate ospf vrf-policy
template policy-grouptemplate policy-group <WORD>
Description: Configure Policy Group Parameters
Syntax:
Interface Policy Group Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1352
T Commandstemplate policy-group
template port-channeltemplate port-channel <WORD>
Description: Configure Port-Channel Parameters
Syntax:
Port-Channel/VPC Name (Max Size 64)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1353
T Commandstemplate port-channel
template route-profiletemplate route-profile <WORD> tenant <WORD>
Description: Configure route-profile template under tenant for BGP dampening and route redistribution
Syntax:
Route-profile template name (Max Size 64)WORD
Tenant for the route-profile templatetenant
Tenant Name (Max Size 63)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route-profile <WORD> tenant <WORD>
template route-profile <WORD>
Description: Configure route-profile template under VRF/L3Out for bridge-domain export
Syntax:
Route-profile template nameWORD
Command Mode: vrf : Configure VRF parameters
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>](config-leaf-vrf)# template route-profile <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1354
T Commandstemplate route-profile
template route tagtemplate route tag <WORD> tenant <WORD>
Description: Configure Route Tag Policy Templates
Syntax:
Route Tag Policy Name (Max Size 64)WORD
Tenant for the Route Tag Policytenant
Tenant Name (Max Size 63)WORD
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template route tag <WORD> tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1355
T Commandstemplate route tag
tenanttenant <WORD>
Description: tenant configuration mode
Syntax:
tenant name (Max Size 63)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1356
T Commandstenant
terminalterminal length <NUMBER>
Description: Enable or disable pager for command output
Syntax:
Terminal length keywordlength
Terminal pager length (0=Disable pager). Number range from=0 to=511NUMBER
Command Mode: exec : Exec Mode
Command Path:
# terminal length <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1357
T Commandsterminal
timetime start <date-time>
Description: Start controller-group upgrade
Syntax:
Set time to trigger upgradestart
Set the start time ([[[yyyy:]mmm:]dd:]HH:MM)<date-time>
Command Mode: controller-group : Controller Upgrade Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# firmware(config-firmware)# controller-group(config-firmware-controller)# time start <date-time>
time start <TIME>
Description: Set the window start time
Syntax:
Set the start timestart
Set the start time [[[yyyy:]mmm:]dd:]HH:MMTIME
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# absolute window <WORD>(config-scheduler-absolute)# time start <TIME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1358
T Commandstime
time start dailytime start daily <TIME>
Description: Specify a daily schedule
Syntax:
Trigger time in HH:MM formatTIME
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# time start daily <TIME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1359
T Commandstime start daily
time start weeklytime start weekly monday|tuesday|wednesday|thursday|friday|saturday|sunday|even-day|odd-day|every-day<TIME>
Description: Specify a weekly schedule
Syntax:
Mondaysmonday
Tuesdaystuesday
Wednesdayswednesday
Thursdaysthursday
Fridaysfriday
Saturdayssaturday
Sundayssunday
Even dayseven-day
Odd daysodd-day
Everydayevery-day
Trigger time in HH:MM formatTIME
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']](config)# scheduler fabric|controller schedule <WORD>(config-scheduler)# recurring window <WORD>(config-scheduler-recurring)# time start weeklymonday|tuesday|wednesday|thursday|friday|saturday|sunday|even-day|odd-day|every-day <TIME>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1360
T Commandstime start weekly
timeouttimeout <NUMBER>
Description: LDAP server timeout for authentication
Syntax:
LDAP server timeout for authentication. Number range from=5 to=60<5-60>
Command Mode: ldap-server host : LDAP server DNS name or IP address
Command Path:
# configure [['terminal', 't']](config)# ldap-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# timeout <NUMBER>
timeout <0-60>
Description: RADIUS server timeout for authentication
Syntax:
RADIUS server timeout for authentication<0-60>
Command Mode: radius-server host : RADIUS server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# radius-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# timeout <0-60>
timeout <NUMBER>
Description: TACACS server timeout for authentication
Syntax:
TACACS server timeout for authentication. Number range from=0to=60
<0-60>
Command Mode: tacacs-server host : TACACS+ server's DNS name or its IP address
Command Path:
# configure [['terminal', 't']](config)# tacacs-server host <A.B.C.D|A:B::C:D|WORD>(config-host)# timeout <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1361
T Commandstimeout
timerstimers bgp <NUMBER> <NUMBER>
Description: Set BGP Policy Timers
Syntax:
Set BGP Policy Timersbgp
Keep-Alive Timer Value in Seconds. Number range from=0 to=3600<0-3600>
Hold Timer Value in Seconds. Number range from=0 to=3600<0-3600>
Command Mode: template bgp timers : Configure Router BGP Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template bgp timers <WORD> tenant <WORD>(config-bgp-timers)# timers bgp <NUMBER> <NUMBER>
timers active-time <NUMBER>
Description: Set EIGRP Timers
Syntax:
Active timer intervalactive-time
Active timer interval value in minutes. Number range from=1 to=65535<1-65535>
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD>(config-template-eigrp-vrf-pol)# timers active-time <NUMBER>
timers active-time <NUMBER>
Description: Set EIGRP Timers
Syntax:
Active timer intervalactive-time
Active timer interval value in minutes. Number range from=1 to=65535<1-65535>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1362
T Commandstimers
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>(config-eigrp-vrf)# address-family ipv4|ipv6 unicast(config-address-family)# timers active-time <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1363
T Commandstimers
timers lsa-arrivaltimers lsa-arrival <NUMBER>
Description: Set the minimum interval between the arrival of each link-state advertisement(LSA)
Syntax:
Interval in milliseconds. Number range from=10 to=600000<10-600000>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers lsa-arrival <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1364
T Commandstimers lsa-arrival
timers lsa-group-pacingtimers lsa-group-pacing <NUMBER>
Description: Set the interval in which LSAs are grouped and refreshed, checksummed, or aged
Syntax:
Interval in seconds. Number range from=1 to=1800<1-1800>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers lsa-group-pacing <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1365
T Commandstimers lsa-group-pacing
timers throttle lsatimers throttle lsa <NUMBER> <NUMBER> <NUMBER>
Description: Set the start-interval, hold-interval, max-interval for LSA
Syntax:
The generation throttle start-wait interval between LSAs.. Number rangefrom=0 to=5000
<start-time 0-5000>
The incremental time (in milliseconds) used to calculate the subsequentrate limiting times for LSA generation.. Number range from=50to=30000
<hold-interval 50-30000>
The generation throttle maximum interval between LSAs.. Numberrange from=50 to=30000
<max-time 50-30000>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers throttle lsa <NUMBER> <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1366
T Commandstimers throttle lsa
timers throttle spftimers throttle spf <NUMBER> <NUMBER> <NUMBER>
Description: Set the SPF init-interval, hold-interval, max-interval for LSA
Syntax:
The initial delay interval for the SPF schedule.. Number range from=1to=600000
<spf-start 1-600000>
The minimum hold time between SPF calculations.. Number rangefrom=1 to=600000
<spf-hold 1-600000>
The maximum interval between SPF calculations. Each interval afterthe initial calculation is twice as long as the previous one until the waitinterval reaches the maximum wait time specified.. Number rangefrom=1 to=600000
<spf-max-wait 1-600000>
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf vrf-policy <WORD> tenant <WORD>(config-vrf-policy)# timers throttle spf <NUMBER> <NUMBER> <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1367
T Commandstimers throttle spf
tptp <WORD>
Description: Set third-party certificate from trusted source/point for device identity
Syntax:
third-party certificate (Max Size 16)<WORD>
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']](config)# crypto keyring <WORD>(config-keyring)# tp <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1368
T Commandstp
transmit-delaytransmit-delay <NUMBER>
Description: Set the delay time needed to send an LSA update packet.
Syntax:
Delay in seconds. Number range from=1 to=450<1-450>
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>(config-interface-policy)# transmit-delay <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1369
T Commandstransmit-delay
transport email fromtransport email from <WORD>
Description: The contact e-mail address
Syntax:
The e-mail address (Max Size None)WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# transport email from <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1370
T Commandstransport email from
transport email mail-servertransport email mail-server <host/ipaddr> [port <port>] [mgmtepg <mgmtepg>]
Description: configure SMTP server
Syntax:
The hostname or ipaddress of the destination<host/ipaddr>
(Optional) Port Number. Number range from=1 to=633535port
(Optional) mgmtepgmgmtepg
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# transport email mail-server <host/ipaddr> [port <port>] [mgmtepg<mgmtepg>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1371
T Commandstransport email mail-server
transport email reply-totransport email reply-to <WORD>
Description: The contact e-mail address
Syntax:
Reply-To e-mail address (Max Size None)WORD
Command Mode: destination-profile : Configure destination profile Parameters
Command Path:
# configure [['terminal', 't']](config)# callhome common(config-callhome)# destination-profile(config-callhome-destnprof)# transport email reply-to <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1372
T Commandstransport email reply-to
trigger fabric-recoverytrigger fabric-recovery <NUMBER> <WORD>
Description: Trigger fabric recovery
Syntax:
Size of the cluster. Number range from=1 to=16<cluster-size>
Snapshot import configuration nameWORD
Command Mode: exec : Exec Mode
Command Path:
# trigger fabric-recovery <NUMBER> <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1373
T Commandstrigger fabric-recovery
trigger shutdowntrigger shutdown controller <NUMBER>
Description: Shutdown controller
Syntax:
Shutdown controllercontroller
Controller id. Number range from=1 to=32<1-32>
Command Mode: exec : Exec Mode
Command Path:
# trigger shutdown controller <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1374
T Commandstrigger shutdown
trigger snapshot downloadtrigger snapshot download <WORD>
Description: Trigger command for snapshot download
Syntax:
Snapshot download configuration nameWORD
Command Mode: exec : Exec Mode
Command Path:
# trigger snapshot download <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1375
T Commandstrigger snapshot download
trigger snapshot exporttrigger snapshot export <WORD>
Description: Trigger command for snapshot export
Syntax:
Snapshot export configuration nameWORD
Command Mode: exec : Exec Mode
Command Path:
# trigger snapshot export <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1376
T Commandstrigger snapshot export
trigger snapshot importtrigger snapshot import <WORD>
Description: Trigger command for snapshot import
Syntax:
Snapshot import configuration nameWORD
Command Mode: exec : Exec Mode
Command Path:
# trigger snapshot import <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1377
T Commandstrigger snapshot import
trigger snapshot rollbacktrigger snapshot rollback <WORD>
Description: Trigger command for snapshot rollback
Syntax:
Snapshot rollback configuration nameWORD
Command Mode: exec : Exec Mode
Command Path:
# trigger snapshot rollback <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1378
T Commandstrigger snapshot rollback
trigger snapshot uploadtrigger snapshot upload <WORD>
Description: Trigger command for snapshot upload
Syntax:
Snapshot upload configuration nameWORD
Command Mode: exec : Exec Mode
Command Path:
# trigger snapshot upload <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1379
T Commandstrigger snapshot upload
trigger techsupport alltrigger techsupport all [remotename <remote-path>]
Description: Trigger techsupport for controllers and switches
Syntax:
(Optional) remote-pathremote-path
Command Mode: exec : Exec Mode
Command Path:
# trigger techsupport all [remotename <remote-path>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1380
T Commandstrigger techsupport all
trigger techsupport controllerstrigger techsupport controllers [remotename <remote-path>]
Description: Trigger techsupport for a controllers
Syntax:
(Optional) remote-pathremote-path
Command Mode: exec : Exec Mode
Command Path:
# trigger techsupport controllers [remotename <remote-path>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1381
T Commandstrigger techsupport controllers
trigger techsupport hosttrigger techsupport host <NUMBER> remotename <remote-file-name> [node <leaf-node-id>]
Description: Trigger techsupport for a host
Syntax:
Specify the host Odev ID. Number range from=0to=9223372036854775807
<Odevid>
Specify the file remote path nameremotename
Remote path file name<remote-file-name>
(Optional) Specify the leaf node id<leaf-node-id>
Command Mode: exec : Exec Mode
Command Path:
# trigger techsupport host <NUMBER> remotename <remote-file-name> [node <leaf-node-id>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1382
T Commandstrigger techsupport host
trigger techsupport localtrigger techsupport local
Description: Trigger techsupport for a local
Command Mode: exec : Exec Mode
Command Path:
# trigger techsupport local
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1383
T Commandstrigger techsupport local
trigger techsupport switchtrigger techsupport switch switchId <switchId> [remotename <remote-path>]
Description: Trigger techsupport for a switch
Syntax:
switch id 101-4000 or range(s): 101-103,104switchId <switchId>
(Optional) remote-pathremote-path
Command Mode: exec : Exec Mode
Command Path:
# trigger techsupport switch switchId <switchId> [remotename <remote-path>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1384
T Commandstrigger techsupport switch
trigger troubleshoot epext session reporttrigger troubleshoot epext session <session_name> report [format <format>]
Description: Trigger a report generation for a troubleshoot session
Syntax:
sessionsession
Session namesession_name
(Optional) Report formatformat
Command Mode: exec : Exec Mode
Command Path:
# trigger troubleshoot epext session <session_name> report [format <format>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1385
T Commandstrigger troubleshoot epext session report
trigger troubleshoot eptoep session reporttrigger troubleshoot eptoep session <session_name> report [format <format>]
Description: Trigger a report generation for a troubleshoot session
Syntax:
sessionsession
Session namesession_name
(Optional) Report formatformat
Command Mode: exec : Exec Mode
Command Path:
# trigger troubleshoot eptoep session <session_name> report [format <format>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1386
T Commandstrigger troubleshoot eptoep session report
trigger vmwaretrigger vmware domain <name> vcenter <hostname|IP> pull-inventory
Description: Trigger VMware vCenter inventory pull
Syntax:
VMware domaindomain
VMM VMware Domain name<name>
VMware vCentervcenter
vCenter hostname or IP<hostname|IP>
Pull inventorypull-inventory
Command Mode: exec : Exec Mode
Command Path:
# trigger vmware domain <name> vcenter <hostname|IP> pull-inventory
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1387
T Commandstrigger vmware
troubleshoot epext session atomiccountertroubleshoot epext session <session_name> atomiccounter
Description: Start atomic counter of a troubleshoot session
Syntax:
sessionsession
session namesession_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> atomiccounter
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1388
T Commandstroubleshoot epext session atomiccounter
troubleshoot epext session descriptiontroubleshoot epext session <session_name> description <LINE>
Description: Set the description of a troubleshoot session
Syntax:
sessionsession
session namesession_name
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> description <LINE>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1389
T Commandstroubleshoot epext session description
troubleshoot epext session latestminutestroubleshoot epext session <session_name> latestminutes <minutes>
Description: Set the time window in number of minutes from current time
Syntax:
sessionsession
session namesession_name
number of minutes from current time. Number range from=5 to=1440minutes
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> latestminutes <minutes>
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1390
T Commandstroubleshoot epext session latestminutes
troubleshoot epext session monitor destination apictroubleshoot epext session <session_name> monitor destination apic srcipprefix <sip/m> [analyser <aip>][erspan-id <id>] [spansrcports <pathep-list>]
Description: Configure this APIC as monitor destination
Syntax:
sessionsession
session namesession_name
destinatondestination
srcipprefixsrcipprefix
Source IP adddress and subnet mask lengthsip/m
(Optional) IP address of the host analyseraip
(Optional) erspan Id. Number range from=1 to=1023id
(Optional) List of source fabricPathEp dnpathep-list
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> monitor destination apic srcipprefix<sip/m> [analyser <aip>] [erspan-id <id>] [spansrcports <pathep-list>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1391
T Commandstroubleshoot epext session monitor destination apic
troubleshoot epext session monitor destination prefdestgrouptroubleshoot epext session <session_name> monitor destination prefdestgroup <destgroup_name>[spansrcports <pathep-list>]
Description: Configure a predefined monitor destination
Syntax:
sessionsession
session namesession_name
destinatondestination
Destination group namedestgroup_name
(Optional) List of source fabricPathEp dnpathep-list
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> monitor destination prefdestgroup<destgroup_name> [spansrcports <pathep-list>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1392
T Commandstroubleshoot epext session monitor destination prefdestgroup
troubleshoot epext session monitor destination tenanttroubleshoot epext session <session_name> monitor destination tenant <tn_name> application <ap_name>epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>] [spansrcports <pathep-list>]
Description: Configure tenant EPG as monitor destination
Syntax:
sessionsession
session namesession_name
destinatondestination
tenant nametn_name
applicationapplication
application nameap_name
epgepg
epg nameepg_name
destipdestip
destination IP addressdip
srcipprefixsrcipprefix
source IP address and subnet mask lengthsip/m
(Optional) erspan Id. Number range from=1 to=1023id
(Optional) List of source fabricPathEp dnpathep-list
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> monitor destination tenant <tn_name>application <ap_name> epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>][spansrcports <pathep-list>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1393
T Commandstroubleshoot epext session monitor destination tenant
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1394
T Commandstroubleshoot epext session monitor destination tenant
troubleshoot epext session schedulertroubleshoot epext session <session_name> scheduler <sch_name> [format <format>]
Description: Associate a scheduler to the troubleshoot session
Syntax:
sessionsession
session namesession_name
scheduler namesch_name
(Optional) Reoport formatformat
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> scheduler <sch_name> [format <format>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1395
T Commandstroubleshoot epext session scheduler
troubleshoot epext session srcextip destip tenant applicationtroubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant <dtenant_name> application<dapp_name> epg <depg_name>
Description: application
Syntax:
sessionsession
session namesession_name
external source IPsip
destipdestip
destination IPdip
tenanttenant
destination Tenantdtenant_name
destination Applicationdapp_name
epgepg
destination EPGdepg_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant<dtenant_name> application <dapp_name> epg <depg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1396
T Commandstroubleshoot epext session srcextip destip tenant application
troubleshoot epext session srcextip destip tenant vrftroubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant <dtenant_name> vrf<dvrf_name>
Description: vrf
Syntax:
sessionsession
session namesession_name
external source IPsip
destipdestip
destination IPdip
tenanttenant
destination Tenantdtenant_name
destination VRFdvrf_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcextip <sip> destip <dip> tenant<dtenant_name> vrf <dvrf_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1397
T Commandstroubleshoot epext session srcextip destip tenant vrf
troubleshoot epext session srcip tenant application epgdestextip
troubleshoot epext session <session_name> srcip <sip> tenant <stenant_name> application <sapp_name>epg <sepg_name> destextip <dip>
Description: External IP
Syntax:
sessionsession
session namesession_name
source IPsip
tenanttenant
source Tenantstenant_name
source Applicationsapp_name
epgepg
source EPGsepg_name
external destination IPdip
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcip <sip> tenant <stenant_name>application <sapp_name> epg <sepg_name> destextip <dip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1398
T Commandstroubleshoot epext session srcip tenant application epg destextip
troubleshoot epext session srcip tenant vrf destextiptroubleshoot epext session <session_name> srcip <sip> tenant <stenant_name> vrf <svrf_name> destextip<dip>
Description: external IP
Syntax:
sessionsession
session namesession_name
source IPsip
tenanttenant
source Tenantstenant_name
source VRFsvrf_name
external destination IPdip
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> srcip <sip> tenant <stenant_name> vrf<svrf_name> destextip <dip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1399
T Commandstroubleshoot epext session srcip tenant vrf destextip
troubleshoot epext session starttimetroubleshoot epext session <session_name> starttime <start_time> endtime <end_time>
Description: Configure the start/end time of the session
Syntax:
sessionsession
session namesession_name
Start time (in YYYY-MM-DDTHH:MM:SS format)start_time
end timeendtime
End time (in YYYY-MM-DDTHH:MM:SS format)end_time
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> starttime <start_time> endtime <end_time>
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1400
T Commandstroubleshoot epext session starttime
troubleshoot epext session traceroutetroubleshoot epext session <session_name> traceroute
Description: Start traceroute of a troubleshoot session
Syntax:
sessionsession
session namesession_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1401
T Commandstroubleshoot epext session traceroute
troubleshoot epext session traceroute protocol icmptroubleshoot epext session <session_name> traceroute protocol icmp
Description: ICMP protocol
Syntax:
sessionsession
session namesession_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute protocol icmp
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1402
T Commandstroubleshoot epext session traceroute protocol icmp
troubleshoot epext session traceroute protocol tcptroubleshoot epext session <session_name> traceroute protocol tcp [destport <port>]
Description: TCP protocol
Syntax:
sessionsession
session namesession_name
(Optional) TCP destination port number. Number range from=0to=65535
port
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute protocol tcp [destport <port>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1403
T Commandstroubleshoot epext session traceroute protocol tcp
troubleshoot epext session traceroute protocol udptroubleshoot epext session <session_name> traceroute protocol udp [destport <port>]
Description: UDP protocol
Syntax:
sessionsession
session namesession_name
(Optional) UDP destination port number. Number range from=0to=65535
port
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot epext session <session_name> traceroute protocol udp [destport <port>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1404
T Commandstroubleshoot epext session traceroute protocol udp
troubleshoot eptoep session atomiccountertroubleshoot eptoep session <session_name> atomiccounter
Description: Start atomic counter of a troubleshoot session
Syntax:
sessionsession
session namesession_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> atomiccounter
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1405
T Commandstroubleshoot eptoep session atomiccounter
troubleshoot eptoep session descriptiontroubleshoot eptoep session <session_name> description <LINE>
Description: Set the description of a troubleshoot session
Syntax:
sessionsession
session namesession_name
Session description, use single quotes with spaces ex: 'my descr' (MaxSize 128)
LINE
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> description <LINE>
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1406
T Commandstroubleshoot eptoep session description
troubleshoot eptoep session latestminutestroubleshoot eptoep session <session_name> latestminutes <minutes>
Description: Set the time window in number of minutes from current time
Syntax:
sessionsession
session namesession_name
number of minutes from current time. Number range from=5 to=1440minutes
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> latestminutes <minutes>
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1407
T Commandstroubleshoot eptoep session latestminutes
troubleshoot eptoep session monitor destination apictroubleshoot eptoep session <session_name> monitor destination apic srcipprefix <sip/m> [analyser <aip>][erspan-id <id>] [spansrcports <pathep-list>]
Description: Configure this APIC as monitor destination
Syntax:
sessionsession
session namesession_name
destinatondestination
srcipprefixsrcipprefix
Source IP adddress and subnet mask lengthsip/m
(Optional) IP address of the host analyseraip
(Optional) erspan Id. Number range from=1 to=1023id
(Optional) List of source fabricPathEp dnpathep-list
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> monitor destination apic srcipprefix<sip/m> [analyser <aip>] [erspan-id <id>] [spansrcports <pathep-list>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1408
T Commandstroubleshoot eptoep session monitor destination apic
troubleshoot eptoep session monitor destination prefdestgrouptroubleshoot eptoep session <session_name> monitor destination prefdestgroup <destgroup_name>[spansrcports <pathep-list>]
Description: Configure a predefined monitor destination
Syntax:
sessionsession
session namesession_name
destinatondestination
Destination group namedestgroup_name
(Optional) List of source fabricPathEp dnpathep-list
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> monitor destination prefdestgroup<destgroup_name> [spansrcports <pathep-list>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1409
T Commandstroubleshoot eptoep session monitor destination prefdestgroup
troubleshoot eptoep session monitor destination tenanttroubleshoot eptoep session <session_name> monitor destination tenant <tn_name> application <ap_name>epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>] [spansrcports <pathep-list>]
Description: Configure tenant EPG as monitor destination
Syntax:
sessionsession
session namesession_name
destinatondestination
tenant nametn_name
applicationapplication
application nameap_name
epgepg
epg nameepg_name
destipdestip
destination IP addressdip
srcipprefixsrcipprefix
source IP address and subnet mask lenghtsip/m
(Optional) erspan Id. Number range from=1 to=1023id
(Optional) List of source fabricPathEp dnpathep-list
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> monitor destination tenant <tn_name>application <ap_name> epg <epg_name> destip <dip> srcipprefix <sip/m> [erspan-id <id>][spansrcports <pathep-list>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1410
T Commandstroubleshoot eptoep session monitor destination tenant
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1411
T Commandstroubleshoot eptoep session monitor destination tenant
troubleshoot eptoep session schedulertroubleshoot eptoep session <session_name> scheduler <sch_name> [format <format>]
Description: Associate a scheduler to the troubleshoot session
Syntax:
sessionsession
session namesession_name
scheduler namesch_name
(Optional) Report formatformat
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> scheduler <sch_name> [format <format>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1412
T Commandstroubleshoot eptoep session scheduler
troubleshoot eptoep session srcip tenant application epg destiptenant application
troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> application <sapp_name>epg <sepg_name> destip <dip> tenant <dtenant_name> application <dapp_name> epg <depg_name>
Description: application
Syntax:
sessionsession
session namesession_name
source IPsip
tenanttenant
source Tenantstenant_name
source Applicationsapp_name
epgepg
source EPGsepg_name
destipdestip
destination IPdip
tenanttenant
destination Tenantdtenant_name
destination Applicationdapp_name
epgepg
destination EPGdepg_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name>application <sapp_name> epg <sepg_name> destip <dip> tenant <dtenant_name> application<dapp_name> epg <depg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1413
T Commandstroubleshoot eptoep session srcip tenant application epg destip tenant application
troubleshoot eptoep session srcip tenant application epg destiptenant vrf
troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> application <sapp_name>epg <sepg_name> destip <dip> tenant <dtenant_name> vrf <dvrf_name>
Description: vrf
Syntax:
sessionsession
session namesession_name
source IPsip
tenanttenant
source Tenantstenant_name
source Applicationsapp_name
epgepg
source EPGsepg_name
destipdestip
destination IPdip
tenanttenant
destination Tenantdtenant_name
destination VRFdvrf_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name>application <sapp_name> epg <sepg_name> destip <dip> tenant <dtenant_name> vrf <dvrf_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1414
T Commandstroubleshoot eptoep session srcip tenant application epg destip tenant vrf
troubleshoot eptoep session srcip tenant vrf destip tenantapplication
troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf <svrf_name> destip<dip> tenant <dtenant_name> application <dapp_name> epg <depg_name>
Description: application
Syntax:
sessionsession
session namesession_name
source IPsip
tenanttenant
source Tenantstenant_name
source VRFsvrf_name
destipdestip
destination IPdip
tenanttenant
destination Tenantdtenant_name
destination Applicationdapp_name
epgepg
destination EPGdepg_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf<svrf_name> destip <dip> tenant <dtenant_name> application <dapp_name> epg <depg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1415
T Commandstroubleshoot eptoep session srcip tenant vrf destip tenant application
troubleshoot eptoep session srcip tenant vrf destip tenant vrftroubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf <svrf_name> destip<dip> tenant <dtenant_name> vrf <WORD>
Description: vrf
Syntax:
sessionsession
session namesession_name
source IPsip
tenanttenant
source Tenantstenant_name
source VRFsvrf_name
destipdestip
destination IPdip
tenanttenant
destination Tenantdtenant_name
destination VRFWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcip <sip> tenant <stenant_name> vrf<svrf_name> destip <dip> tenant <dtenant_name> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1416
T Commandstroubleshoot eptoep session srcip tenant vrf destip tenant vrf
troubleshoot eptoep session srcmac tenant application epgdestmac tenant application
troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> application<sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> application <dapp_name> epg<depg_name>
Description: application
Syntax:
sessionsession
session namesession_name
source MACsmac
tenanttenant
source Tenantstenant_name
source Applicationsapp_name
epgepg
source EPGsepg_name
destmacdestmac
destination MACdmac
tenanttenant
destination Tenantdtenant_name
destination Applicationdapp_name
epgepg
destination EPGdepg_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>application <sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> application
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1417
T Commandstroubleshoot eptoep session srcmac tenant application epg destmac tenant application
<dapp_name> epg <depg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1418
T Commandstroubleshoot eptoep session srcmac tenant application epg destmac tenant application
troubleshoot eptoep session srcmac tenant application epgdestmac tenant vrf
troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> application<sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>
Description: vrf
Syntax:
sessionsession
session namesession_name
source MACsmac
tenanttenant
source Tenantstenant_name
source Applicationsapp_name
epgepg
source EPGsepg_name
destmacdestmac
destination MACdmac
tenanttenant
destination Tenantdtenant_name
destination VRFdvrf_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>application <sapp_name> epg <sepg_name> destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1419
T Commandstroubleshoot eptoep session srcmac tenant application epg destmac tenant vrf
troubleshoot eptoep session srcmac tenant vrf destmac tenantapplication
troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> vrf <svrf_name>destmac <dmac> tenant <dtenant_name> application <dapp_name> epg <depg_name>
Description: application
Syntax:
sessionsession
session namesession_name
source MACsmac
tenanttenant
source Tenantstenant_name
source VRFsvrf_name
destmacdestmac
destination MACdmac
tenanttenant
destination Tenantdtenant_name
destination Applicationdapp_name
epgepg
destination EPGdepg_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>vrf <svrf_name> destmac <dmac> tenant <dtenant_name> application <dapp_name> epg <depg_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1420
T Commandstroubleshoot eptoep session srcmac tenant vrf destmac tenant application
troubleshoot eptoep session srcmac tenant vrf destmac tenantvrf
troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name> vrf <svrf_name>destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>
Description: vrf
Syntax:
sessionsession
session namesession_name
source MACsmac
tenanttenant
source Tenantstenant_name
source VRFsvrf_name
destmacdestmac
destination MACdmac
tenanttenant
destination Tenantdtenant_name
destination VRFdvrf_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> srcmac <smac> tenant <stenant_name>vrf <svrf_name> destmac <dmac> tenant <dtenant_name> vrf <dvrf_name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1421
T Commandstroubleshoot eptoep session srcmac tenant vrf destmac tenant vrf
troubleshoot eptoep session starttimetroubleshoot eptoep session <session_name> starttime <start_time> endtime <end_time>
Description: Configure the start/end time of the session
Syntax:
sessionsession
session namesession_name
Start time (in YYYY-MM-DDTHH:MM:SS format)start_time
end timeendtime
End time (in YYYY-MM-DDTHH:MM:SS format)end_time
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> starttime <start_time> endtime <end_time>
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1422
T Commandstroubleshoot eptoep session starttime
troubleshoot eptoep session traceroutetroubleshoot eptoep session <session_name> traceroute
Description: Start traceroute of a troubleshoot session
Syntax:
sessionsession
session namesession_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1423
T Commandstroubleshoot eptoep session traceroute
troubleshoot eptoep session traceroute protocol icmptroubleshoot eptoep session <session_name> traceroute protocol icmp
Description: ICMP protocol
Syntax:
sessionsession
session namesession_name
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute protocol icmp
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1424
T Commandstroubleshoot eptoep session traceroute protocol icmp
troubleshoot eptoep session traceroute protocol tcptroubleshoot eptoep session <session_name> traceroute protocol tcp [destport <port>]
Description: TCP protocol
Syntax:
sessionsession
session namesession_name
(Optional) TCP destination port number. Number range from=0to=65535
port
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute protocol tcp [destport<port>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1425
T Commandstroubleshoot eptoep session traceroute protocol tcp
troubleshoot eptoep session traceroute protocol udptroubleshoot eptoep session <session_name> traceroute protocol udp [destport <port>]
Description: UDP protocol
Syntax:
sessionsession
session namesession_name
(Optional) UDP destination port number. Number range from=0to=65535
port
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# troubleshoot eptoep session <session_name> traceroute protocol udp [destport<port>]
Usage Note:
The usage of the troubleshoot epext session commands and the troubleshoot eptoep session commandsdiffers in the following way:
• Use the troubleshoot epext session command when one endpoint is local to the fabric and the otherendpoint is external to the fabric.
• Use the troubleshoot eptoep session command when both endpoints are local to the fabric.
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1426
T Commandstroubleshoot eptoep session traceroute protocol udp
trusted-keytrusted-key <id>
Description: Configure trusted for ntp authentication key
Syntax:
Id for the trusted key. Number range from=1 to=65535id
Command Mode: ntp : Configure the default ntp policy
Command Path:
# configure [['terminal', 't']](config)# pod 1(config-pod)# ntp(config-ntp)# trusted-key <id>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1427
T Commandstrusted-key
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1428
T Commandstrusted-key
U Commands
• ui-idle-timeout-seconds, page 1430
• unicast, page 1431
• update-source ethernet, page 1432
• update-source loopback, page 1433
• update-source vlan, page 1434
• use-keyring, page 1435
• use-vrf, page 1436
• user, page 1437
• username, page 1438
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1429
ui-idle-timeout-secondsui-idle-timeout-seconds <NUMBER>
Description: Set maximum GUI idle duration before requiring login refresh
Syntax:
Set maximumGUI idle duration before requiring login refresh. Numberrange from=60 to=65525
<60-65525>
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# ui-idle-timeout-seconds <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1430
U Commandsui-idle-timeout-seconds
unicastunicast routing
Description: Instruct the fabric to route based on IP
Syntax:
Unicast routing settingrouting
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# unicast routing
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1431
U Commandsunicast
update-source ethernetupdate-source ethernet <interfaceRange>
Description: Source Ethernet Interface
Syntax:
<interfaceRange><interfaceRange>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# update-source ethernet <interfaceRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1432
U Commandsupdate-source ethernet
update-source loopbackupdate-source loopback <A.B.C.D>
Description: Source Loopback Interface
Syntax:
IPv4 or IPv6 Address without maskA.B.C.D
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# update-source loopback <A.B.C.D>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1433
U Commandsupdate-source loopback
update-source vlanupdate-source vlan <vlan>
Description: Source Vlan Interface
Syntax:
Vlan ID<vlan>
Command Mode: neighbor : Configure a BGP neighbor
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# update-source vlan <vlan>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1434
U Commandsupdate-source vlan
use-keyringuse-keyring <keyring-name>
Description: Use specified keyring for the HTTPS Server SSL certificate
Syntax:
Keyring name (Max Size 64)keyring-name
Command Mode: https : HTTPS communication policy group
Command Path:
# configure [['terminal', 't']](config)# comm-policy <WORD>(config-comm-policy)# https(config-https)# use-keyring <keyring-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1435
U Commandsuse-keyring
use-vrfuse-vrf <arg>
Description: Configure the management vrf for dns servers
Syntax:
Configure management vrfarg
Command Mode: dns : Configure default dns policy
Command Path:
# configure [['terminal', 't']](config)# dns(config-dns)# use-vrf <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1436
U Commandsuse-vrf
useruser <WORD>
Description: Set the remote path user name and password
Syntax:
User nameWORD
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']](config)# remote path <WORD>(config-remote)# user <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1437
U Commandsuser
usernameusername <WORD>
Description: Create a locally-authenticated user account
Syntax:
User name (Max Size 28)WORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# username <WORD>
username <WORD>
Description: Configure a user account for the VCenter
Syntax:
Username for the accountWORD
Command Mode: vcenter : Configure a VCenter in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# username <WORD>
username <WORD>
Description: Configure a user account for the vshield
Syntax:
Username for the accountWORD
Command Mode: vshield : Configure a VShield in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1438
U Commandsusername
(config-vmware-vc-vs)# username <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1439
U Commandsusername
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1440
U Commandsusername
V Commands
• vcenter, page 1442
• vlan-domain, page 1443
• vlan-pool, page 1447
• vlan, page 1448
• vmware-domain, page 1450
• vnic, page 1451
• vpc context, page 1452
• vpc domain consecutive, page 1453
• vpc domain explicit, page 1454
• vpc domain reciprocal, page 1455
• vrf, page 1456
• vshield, page 1461
• vxlan, page 1462
• vxlan multicast-pool, page 1463
• vxlan pool, page 1464
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1441
vcentervcenter <arg> datacenter <WORD> [dvs-version <arg>]
Description: Configure a VCenter in the VMware domain
Syntax:
arg
Datacenter Namedatacenter
Datacenter NameWORD
(Optional)arg
Command Mode: vmware-domain : Create a VMM VMware Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1442
V Commandsvcenter
vlan-domainvlan-domain <name> [dynamic] [type <domain-type>]
Description: Configure vlan domain
Syntax:
Vlan domain name (Max Size 64)name
(Optional) Create dynamic namespace(default is static)dynamic
(Optional) Vlan domain type<domain-type>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>]
vlan-domain member <WORD> [type <arg>]
Description: Attach VMware Domain to a VLAN Domain
Syntax:
Bind VMware domain to vlan domainmember
VLAN Domain nameWORD
(Optional) Vlan domain typearg
Command Mode: vmware-domain : Create a VMM VMware Domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vlan-domain member <WORD> [type <>]
vlan-domain member <WORD> [type <arg>]
Description: Attach Microsoft Domain to a VLAN Domain
Syntax:
Bind Microsoft domain to vlan domainmember
VLAN Domain nameWORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1443
V Commandsvlan-domain
(Optional) Vlan domain typearg
Command Mode: microsoft-domain : Create a VMMMicrosoft Domain
Command Path:
# configure [['terminal', 't']](config)# microsoft-domain <WORD>(config-microsoft)# vlan-domain member <WORD> [type <>]
vlan-domain member <WORD> [type <arg>]
Description: Configure Vlan Domain
Syntax:
Configure Vlan Domain Membermember
Vlan domain name (Max Size 64)WORD
(Optional)arg
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']](config)# template policy-group <WORD>(config-pol-grp-if)# vlan-domain member <WORD> [type <>]
vlan-domain member <WORD> [type <arg>]
Description: Configure Vlan Domain
Syntax:
Configure Vlan Domain Membermember
Vlan domain name (Max Size 64)WORD
(Optional)arg
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']](config)# template port-channel <WORD>(config-if)# vlan-domain member <WORD> [type <>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1444
V Commandsvlan-domain
vlan-domain member <WORD> [type <arg>]
Description: Configure Vlan Domain
Syntax:
Configure Vlan Domain Membermember
Vlan domain name (Max Size 64)WORD
(Optional)arg
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>(config-leaf-if)# vlan-domain member <WORD> [type <>]
vlan-domain member <WORD> [type <arg>]
Description: Configure Vlan Domain
Syntax:
Configure Vlan Domain Membermember
Vlan domain name (Max Size 64)WORD
(Optional)arg
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface port-channel <WORD> [fex <fex>](config-leaf-if)# vlan-domain member <WORD> [type <>]
vlan-domain member <WORD> [type <arg>]
Description: Configure Vlan Domain
Syntax:
Configure Vlan Domain Membermember
Vlan domain name (Max Size 64)WORD
(Optional)arg
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1445
V Commandsvlan-domain
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>](config-vpc)# interface vpc <WORD> [fex <fex>](config-vpc-if)# vlan-domain member <WORD> [type <>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1446
V Commandsvlan-domain
vlan-poolvlan-pool <pool-name>
Description: Assign vlan-pool to vlan-domain
Syntax:
Vlan-pool name (Max Size 64)pool-name
Command Mode: vlan-domain : Configure vlan domain
Command Path:
# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# vlan-pool <pool-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1447
V Commandsvlan-pool
vlanvlan <vlan-range> [dynamic]
Description: Add VLANs to vlan-domain
Syntax:
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19<vlan-range>
(Optional) Vlan allocation dynamically managed by APIC(default isstatic)
dynamic
Command Mode: vlan-domain : Configure vlan domain
Command Path:
# configure [['terminal', 't']](config)# vlan-domain <name> [dynamic] [type <domain-type>](config-vlan)# vlan <vlan-range> [dynamic]
vlan <1-4094>
Description: Configure Vlan for inband epg Controller inband ports
Syntax:
Vlan interface number<1-4094>
Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties orcreate new inband
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# inband-mgmt epg <WORD>(config-inb-epg)# vlan <1-4094>
vlan <1-4094>
Description: Configure Vlan for APIC Inband Port
Syntax:
Vlan interface number<1-4094>
Command Mode: interface inband-mgmt0 : Inband management interface
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1448
V Commandsvlan
Command Path:
# configure [['terminal', 't']](config)# controller(config-controller)# interface inband-mgmt0(config-controller-if)# vlan <1-4094>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1449
V Commandsvlan
vmware-domainvmware-domain <WORD>
Description: Create a VMM VMware Domain
Syntax:
VMM VMware Domain nameWORD
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>
vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>] [allow-micro-segmentation][deploy <WORD>] [push <WORD>]
Description: Associate EPG to a VMWare Domain
Syntax:
Bind the EPG to a VMware domainmember
VMware Domain NameWORD
(Optional) Enforce encap value. Secondary encapwhen EPG is isolated(For example vlan-10 or auto)
WORD
(Optional) Primary encap when EPG is isolated (For example vlan-11or auto)
WORD
(Optional) allow-micro-segmentationallow-micro-segmentation
(Optional) Deployment modeWORD
(Optional) Push modeWORD
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>][allow-micro-segmentation] [deploy <WORD>] [push <WORD>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1450
V Commandsvmware-domain
vnicvnic <vnic-name>
Description: Configure Virtual NIC as Cluster Member Interface
Syntax:
Name of VNIC of virtual cluster device.<vnic-name>
Command Mode: member : Configure Cluster Interface Member
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service<service>] [function <function>](config-cluster)# cluster-interface <WORD> [vlan <NUMBER>](config-cluster-interface)# member device <WORD> device-interface <WORD>(config-member)# vnic <vnic-name>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1451
V Commandsvnic
vpc contextvpc context leaf <101-4000> <101-4000> [fex <fex>]
Description: Enter vpc context
Syntax:
Provide leaf detailsleaf
Id or Name of Leaf1<101-4000>
Id or Name of Leaf2<101-4000>
(Optional) Fex Id. Number range from=101 to=164fex
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# vpc context leaf <101-4000> <101-4000> [fex <fex>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1452
V Commandsvpc context
vpc domain consecutivevpc domain consecutive
Description: Pair all discovered leaves consecutively e.g. 101-102, 103-104
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# vpc domain consecutive
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1453
V Commandsvpc domain consecutive
vpc domain explicitvpc domain explicit <NUMBER> leaf <101-4000> <101-4000>
Description: Pair two leaf nodes explicitly
Syntax:
Domain Id. Number range from=1 to=1000<1-1000>
Pair two leaf nodesleaf
First leaf member of the Pair<101-4000>
Second leaf member of the Pair<101-4000>
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# vpc domain explicit <NUMBER> leaf <101-4000> <101-4000>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1454
V Commandsvpc domain explicit
vpc domain reciprocalvpc domain reciprocal
Description: Pair all discovered leaves reciprocally e.g. 101-103, 102-104
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# vpc domain reciprocal
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1455
V Commandsvpc domain reciprocal
vrfvrf context <WORD>
Description: Configuration for vrf
Syntax:
VRF namecontext
VRF name (Max Size 64)WORD
Command Mode: tenant : tenant configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# vrf context <WORD>
vrf member <WORD>
Description: Configure VRF parameters
Syntax:
Set L3Out's VRF membershipmember
VRF nameWORD
Command Mode: l3out : Configuration for L3Out
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# l3out <WORD>(config-tenant-l3out)# vrf member <WORD>
vrf member <WORD>
Description: Associate the bridge-domain with a VRF
Syntax:
Associate the bridge-domain with a VRFmember
VRF name to associated (Max Size 64)WORD
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1456
V Commandsvrf
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# bridge-domain <WORD>(config-tenant-bd)# vrf member <WORD>
vrf member <WORD>
Description: Configure VRF parameters
Syntax:
Set interface's VRF membershipmember
VRF nameWORD
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>](config-tenant-l3ext-epg)# vrf member <WORD>
vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
Description: Configure VRF parameters
Syntax:
Enable VRF and enter VRF modecontext
Tenant for the VRFtenant
Tenant nameWORD
Virtual Routing and Forwarding instancevrf
VRF nameWORD
(Optional) Configure VRF in API created l3outl3out
Command Mode: leaf : Configure Leaf Node
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1457
V Commandsvrf
vrf member tenant <WORD> vrf <WORD>
Description: Configure VRF parameters
Syntax:
Set interface's VRF membershipmember
Tenanttenant
Tenant nameWORD
Virtual Routing and Forwarding instancevrf
VRF nameWORD
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface vlan <1-4094>(config-leaf-if)# vrf member tenant <WORD> vrf <WORD>
vrf member tenant <WORD> vrf <WORD> [l3out] WORD
Description: Configure VRF parameters
Syntax:
Set interface's VRF membershipmember
Tenanttenant
Tenant nameWORD
Virtual Routing and Forwarding instancevrf
VRF nameWORD
(Optional) Enable VRF on one or more l3extOutl3out
l3extOut NameWORD
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# interface ethernet <ifRange>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1458
V Commandsvrf
(config-leaf-if)# vrf member tenant <WORD> vrf <WORD> [l3out] WORD
vrf member tenant <WORD> vrf <WORD>
Description: Configure VRF information
Syntax:
Set VRF membershipmember
Tenanttenant
Tenant nameWORD
VRFvrf
VRF nameWORD
Command Mode: router eigrp : Enhanced Interior Gateway Routing Protocol (EIGRP)
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router eigrp default(config-eigrp)# vrf member tenant <WORD> vrf <WORD>
vrf member tenant <WORD> vrf <WORD>
Description: Associate Router OSPF Policy with Tenant/VRF
Syntax:
Set VRF membershipmember
Tenant for the OSPF Policytenant
Tenant nameWORD
VRFvrf
VRF nameWORD
Command Mode: router ospf : Open Shortest Path First (OSPF and OSPF Version3)
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router ospf default(config-leaf-ospf)# vrf member tenant <WORD> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1459
V Commandsvrf
vrf member tenant <WORD> vrf <WORD>
Description: Virtual Router Context
Syntax:
Set BGP's VRF membershipmember
Tenant for the BGP Policytenant
Tenant Name (Max Size 63)WORD
Virtual Routing and Forwarding instancevrf
VRF Name (Max Size 64)WORD
Command Mode: router bgp : Border Gateway Protocol (BGP)
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1460
V Commandsvrf
vshieldvshield <arg>
Description: Configure a VShield in the VMware domain
Syntax:
arg
Command Mode: vcenter : Configure a VCenter in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1461
V Commandsvshield
vxlanvxlan multicast-pool <ip-range>
Description: Configure VXLAN multicast pool.
Syntax:
multicast poolmulticast-pool
Multicast IP range<ip-range>
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# configure-avs(config-vmware-avs)# vxlan multicast-pool <ip-range>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1462
V Commandsvxlan
vxlan multicast-poolvxlan multicast-pool <ip-range>
Description: Configure VXLAN multicast pool.
Syntax:
Multicast IP range<ip-range>
Command Mode: vshield : Configure a VShield in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>(config-vmware-vc-vs)# vxlan multicast-pool <ip-range>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1463
V Commandsvxlan multicast-pool
vxlan poolvxlan pool <vxlan-range>
Description: Configure VXLAN pool.
Syntax:
VXLAN range<vxlan-range>
Command Mode: vshield : Configure a VShield in the VMware domain
Command Path:
# configure [['terminal', 't']](config)# vmware-domain <WORD>(config-vmware)# vcenter <> datacenter <WORD> [dvs-version <>](config-vmware-vc)# vshield <>(config-vmware-vc-vs)# vxlan pool <vxlan-range>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1464
V Commandsvxlan pool
W Commands
• webtoken-timeout-seconds, page 1466
• weight, page 1467
• where, page 1468
• where detail, page 1469
• winservers, page 1470
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1465
webtoken-timeout-secondswebtoken-timeout-seconds <NUMBER>
Description: Set The web token timeout interval
Syntax:
Set The web token timeout interval. Number range from=300 to=9600<300-9600>
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']](config)# crypto webtoken(config-webtoken)# webtoken-timeout-seconds <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1466
W Commandswebtoken-timeout-seconds
weightweight <NUMBER>
Description:Weight attribute that is local to a router.
Syntax:
Assigns a weight to all routes learned through the neighbor. Numberrange from=0 to=65535
<0-65535>
Command Mode: address-family : Configure an address-family for peer
Command Path:
# configure [['terminal', 't']](config)# leaf <101-4000>(config-leaf)# router bgp <fabric-ASN>(config-bgp)# vrf member tenant <WORD> vrf <WORD>(config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>](config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast(config-leaf-bgp-vrf-neighbor-af)# weight <NUMBER>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1467
W Commandsweight
wherewhere
Description: show the current mode
Command Mode: exec : Exec Mode
Command Path:
# where
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1468
W Commandswhere
where detailwhere detail
Description: show detailed mode information
Command Mode: exec : Exec Mode
Command Path:
# where detail
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1469
W Commandswhere detail
winserverswinservers <windows server ip>
Description: Add windows server
Syntax:
windows server ipwindows server ip
Command Mode: microsoft : Configure static ip pool
Command Path:
# configure [['terminal', 't']](config)# tenant <WORD>(config-tenant)# application <WORD>(config-tenant-app)# epg <WORD> [type <WORD>](config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>(config-tenant-app-epg-ms-ip-pool)# winservers <windows server ip>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1470
W Commandswinservers
Z Commands
• zone, page 1472
• zones, page 1473
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1471
zonezone <WORD>
Description: Create zone policy
Syntax:
zone name (Max Size 64)WORD
Command Mode: zones : Zones configuration Mode
Command Path:
# configure [['terminal', 't']](config)# zones(config-zones)# zone <WORD>
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1472
Z Commandszone
zoneszones
Description: Zones configuration Mode
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']](config)# zones
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2) 1473
Z Commandszones
Cisco APIC NX-OS Style CLI Command Reference, Release 1.2(2)1474
Z Commandszones
Top Related