Channel Equalization
Po-Han Huang
MS. Electrical Engineering
Abhinandan Majumdar
MS Computer Engineering
Digital Signal Processing Final Project
EE 4810
2007 Fall
Professor Dan Ellis
I�DEX
1. I�TRODUCTIO� ..................................................................................................................1
1.1 Channel Equalization ..........................................................................................................1
1.2 Types ...................................................................................................................................2
1.2.1 Linear Equalizer ......................................................................................................2
1.2.2 Decision Feedback Equalizer ..................................................................................2
1.2.3 Adaptive Equalizer ..................................................................................................3
2. THEORY .................................................................................................................................4
2.1 The Problem Statement .......................................................................................................4
2.2 System Identification ..........................................................................................................4
2.3 Algorithm ............................................................................................................................6
3. RESULT ..................................................................................................................................7
3.1 Actual Input Signal for Sxx .................................................................................................7
3.1.1 Zero Phase Filter .....................................................................................................7
3.1.2 Linear Phase Filter ................................................................................................10
3.2 Different Signal for Sxx .....................................................................................................11
3.2.1 Zero Phase Filter ...................................................................................................12
3.2.2 Linear Phase Filter ................................................................................................13
3.3 Approximated Sxx .............................................................................................................14
3.3.1 Zero Phase Filter ...................................................................................................15
3.3.2 Linear Phase Filter ................................................................................................16
4. CO�CLUSIO� .....................................................................................................................18
4.1 Concise Result ..................................................................................................................18
4.2 Future Work ......................................................................................................................18
4.3 Experience .........................................................................................................................18
5. REFERE�CE ........................................................................................................................19
APPE�DIX ..................................................................................................................................20
1. I�TRODUCTIO�
In audio processing, equalization is the process of changing the frequency envelope of a sound.
In passing through any channel, temporal/frequency spreading of a signal
it means to correct, or make equal, the frequency response of a signal. The term "equalizer" is
often incorrectly applied as a general term for audio filters. These are in fact general all
filters, which can be arranged to p
stop filters. Only when these filters are arranged so as to reverse the effects of the internal
circuitry on sound output, are they operating as equalizers.
1.1 Channel Equalization
To combat the distortive channel effects, or in other words, invert the FIR filter (time
or time-varying) representing the channel, a so
system, the transmitter sends the information over an RF channel.
channel, the signal gets distorted before actually it gets received at the receiver end. Hence, it is
the receiver ”task” is to figure out what signal was transmitted and turn the received signal in
understandable information.
The purpose of an equalizer is to reduce the ISI as much as possible to maximize the probability
of correct decisions.
1
I�TRODUCTIO�
In audio processing, equalization is the process of changing the frequency envelope of a sound.
In passing through any channel, temporal/frequency spreading of a signal occurs. Etymologically,
it means to correct, or make equal, the frequency response of a signal. The term "equalizer" is
often incorrectly applied as a general term for audio filters. These are in fact general all
filters, which can be arranged to produce the effect of low pass, high pass, band pass and band
stop filters. Only when these filters are arranged so as to reverse the effects of the internal
circuitry on sound output, are they operating as equalizers.
Channel Equalization
tortive channel effects, or in other words, invert the FIR filter (time
varying) representing the channel, a so-called equalizer is needed.
system, the transmitter sends the information over an RF channel. On passing th
channel, the signal gets distorted before actually it gets received at the receiver end. Hence, it is
receiver ”task” is to figure out what signal was transmitted and turn the received signal in
Fig 1.1 Inter symbol Interference
The purpose of an equalizer is to reduce the ISI as much as possible to maximize the probability
In audio processing, equalization is the process of changing the frequency envelope of a sound.
occurs. Etymologically,
it means to correct, or make equal, the frequency response of a signal. The term "equalizer" is
often incorrectly applied as a general term for audio filters. These are in fact general all-purpose
roduce the effect of low pass, high pass, band pass and band
stop filters. Only when these filters are arranged so as to reverse the effects of the internal
tortive channel effects, or in other words, invert the FIR filter (time-invariant
called equalizer is needed. In a communication
On passing through the
channel, the signal gets distorted before actually it gets received at the receiver end. Hence, it is
receiver ”task” is to figure out what signal was transmitted and turn the received signal in
The purpose of an equalizer is to reduce the ISI as much as possible to maximize the probability
1.2 Types
1.2.1 Linear Equalizer
In a Linear Equalizer, t
weighted by equalizer coefficients a
below.
a) Zero forcing equalizer
without taking in consideration the resul
substantial increment of the noise power
b) Mean-Square Error equalizer
total error between the slicer input and the transmitted
1.2.2 Decision Feedback Equalizer
It is a simple nonlinear equalizer which is particulary useful for channel with severe
amplitude distortion. It
which have already have been detected.
already detected are known (past decisions are assumed correct), then the ISI contributed
by these symbols can be canceled exactly.
In a Decision Feedback Equalizer Architecture, t
may be adjusted simultaneously to minimize the M
2
a Linear Equalizer, the current and the past values of the received signal are linearly
equalizer coefficients and summed to produce the output, using the relation
Zero forcing equalizer – In such type of equalizers, it removes the complete ISI
ng in consideration the resulting noise enhacement
increment of the noise power.
Square Error equalizer – Such type of equlaizers attempt to minimize the
total error between the slicer input and the transmitted data symbol.
Decision Feedback Equalizer
imple nonlinear equalizer which is particulary useful for channel with severe
It uses desicion feedback to cancel the interferfence from symbols
which have already have been detected. The basic idea is that if the values of the symbols
already detected are known (past decisions are assumed correct), then the ISI contributed
by these symbols can be canceled exactly.
In a Decision Feedback Equalizer Architecture, the forward and feedback
may be adjusted simultaneously to minimize the Mean Square Error.
Fig 1.2 Decision Feedback Equalizer
he current and the past values of the received signal are linearly
nd summed to produce the output, using the relation
In such type of equalizers, it removes the complete ISI
ting noise enhacement. Using this, there is a
attempt to minimize the
data symbol.
imple nonlinear equalizer which is particulary useful for channel with severe
uses desicion feedback to cancel the interferfence from symbols
The basic idea is that if the values of the symbols
already detected are known (past decisions are assumed correct), then the ISI contributed
he forward and feedback coefficients
ean Square Error.
1.2.3 Adaptive Equalizers
This type of equlaizers adapt the coefficients to minimize the noise and intersymbol
interference (depending on the
There are two modes that adaptive equalizers work;
a) Decision Directed Mode:
Decision directed equalizer adjustment is effective i
channel response. However, this approach is not effective during initial acqusition .
b) Training Mode: To make equalizer suitable in the initial acqusition duration, a training
signal is needed. In this mode of operation, the transmitter generates a data symbol
sequence known to the receiver.
Once an agreed time has elapsed, the slicer output is
actual data transmission begins.
3
This type of equlaizers adapt the coefficients to minimize the noise and intersymbol
interference (depending on the type of equalizer) at the output.
Fig 1.3 Adaptive Equalizers
There are two modes that adaptive equalizers work;
Decision Directed Mode: The receiver decisions are used to generate the error signal.
Decision directed equalizer adjustment is effective in tracking slow variations in the
channel response. However, this approach is not effective during initial acqusition .
To make equalizer suitable in the initial acqusition duration, a training
signal is needed. In this mode of operation, the transmitter generates a data symbol
sequence known to the receiver.
Once an agreed time has elapsed, the slicer output is used as a training
actual data transmission begins.
This type of equlaizers adapt the coefficients to minimize the noise and intersymbol
he receiver decisions are used to generate the error signal.
n tracking slow variations in the
channel response. However, this approach is not effective during initial acqusition .
To make equalizer suitable in the initial acqusition duration, a training
signal is needed. In this mode of operation, the transmitter generates a data symbol
training signal and the
2. THEORY
2.1 The Problem Statement
The problem being dealt here is an unk
being passed through unknown channel. The object is to regenerate the original sample(X) from
the filtered sample(Y).
2.2 System Identification
In an Energy Density Spectrum
x[n] from Energy Density Spectrum of input signal S
This spectrum can be evaluated by taking the DTFTs of the autocorrelation sequence r
input sequence x[n] and the autocorrelation sequence r
a stable LTI discrete time system with an impulse response h[n],
And our application, the input signal x[n] is not known, this sys
computing the autocorrelation of the output signal y[n] defined by,
4
The Problem Statement
problem being dealt here is an unknown input signal X underwent unwanted filtering after
being passed through unknown channel. The object is to regenerate the original sample(X) from
Fig 2.1 Channel Equalization
System Identification
In an Energy Density Spectrum technique of system identification, we compute the input signal
x[n] from Energy Density Spectrum of input signal Sxx(���) and that of output signal S
This spectrum can be evaluated by taking the DTFTs of the autocorrelation sequence r
input sequence x[n] and the autocorrelation sequence ryy[l] of output sequence y[n]
a stable LTI discrete time system with an impulse response h[n],
���� � ������ ���
����
And our application, the input signal x[n] is not known, this system can be identified by
computing the autocorrelation of the output signal y[n] defined by,
input signal X underwent unwanted filtering after
being passed through unknown channel. The object is to regenerate the original sample(X) from
technique of system identification, we compute the input signal
) and that of output signal Syy(���).
This spectrum can be evaluated by taking the DTFTs of the autocorrelation sequence rxx[l] of
[l] of output sequence y[n]. Considering
tem can be identified by
5
������ � ������� ���
����
From the above equations,
������ � � ������ ���
����� � �� ����� � + ���
�����
�
����
� ��� �� � ���
����� ��� ����� � + ���
�����
�
����
� ��� �� � ���
��������� � ��
�
����� ��� ⊛ � �� ⊛ ������
Hence, in the z – domain, the equation becomes,
����� � !�� !���" �����
where, ����� is the z – transform of ������. On the unit circle, the above equation reduces to
From, the above relation, the autocorrelation of the output signal can provide only the magnitude
response of the system but not the phase response.
���#���$ � %!#���$%&�������
2.3 Algorithm
Here, we only have the filtered sample. Hence we kind of approximate S
average of various speech samples considered for our experiment. Hence, we find the
autocorrelation of the sequence y,
response of ryy as Syy. Then we perform division of S
the square root of it and divide it to Y which is the DTFT of output sample to get frequency
components of regenerated input sample. Then we perform Inverse DTFT by passing it through
IFFT block to get the regenerate input sample in time domain.
As discussed before, by this approach, we lose the phase information being added by the filter,
hence we need to make approximation on filter characteristics so as to minimize θ
θx ≈ θy. Hence in a nutshell, approximations being made are listed below.
a) We approximate on Sxx values by taking the DTFT of the
the input speech samples.
b) We approximate that the filter channel characteristics are that of zero phase or linear
phase filter so as θH ≈ 0.
6
Fig 2.2 Block Diagram of Algorithm
filtered sample. Hence we kind of approximate S
average of various speech samples considered for our experiment. Hence, we find the
autocorrelation of the sequence y, and then pass it through FFT block to get the Frequency
. Then we perform division of Syy and Sxx to get |H(z)|
the square root of it and divide it to Y which is the DTFT of output sample to get frequency
erated input sample. Then we perform Inverse DTFT by passing it through
IFFT block to get the regenerate input sample in time domain.
As discussed before, by this approach, we lose the phase information being added by the filter,
roximation on filter characteristics so as to minimize θ
. Hence in a nutshell, approximations being made are listed below.
We approximate on Sxx values by taking the DTFT of the autocorrelation
the input speech samples.
We approximate that the filter channel characteristics are that of zero phase or linear
≈ 0.
filtered sample. Hence we kind of approximate Sxx values, which is the
average of various speech samples considered for our experiment. Hence, we find the
pass it through FFT block to get the Frequency
to get |H(z)|2. Then we perform
the square root of it and divide it to Y which is the DTFT of output sample to get frequency
erated input sample. Then we perform Inverse DTFT by passing it through
As discussed before, by this approach, we lose the phase information being added by the filter,
roximation on filter characteristics so as to minimize θH, resultantly
autocorrelation of average of
We approximate that the filter channel characteristics are that of zero phase or linear
7
3. RESULTS
For our experimentation purpose, we ran three type of simulation each with zero and linear phase
which are described in detail below.
3.1 Actual Input Signal for Sxx
3.1.1 Zero Phase Filter
Here we passed through a length 11 zero-phase FIR lowpass filter designed using the Remez
exchange algorithm. The matlab code for designing this filter is as follows:
N = 11; % filter length - must be odd b = [0 0.1 0.2 0.5]*2; % band edges M = [1 1 0 0 ]; % desired band values h = remez(N-1,b,M); % Remez multiple exchange design
The impulse response is returned in linear-phase form, so it must be left-shifted (N-1)/2 samples
to make it zero phase.
Figure 3.1: Impulse response and frequency response of a length 11 zero-phase FIR lowpass filter. Here the
frequency response is real because the filter is zero phase. Also plotted (in dashed lines) are the desired passband
and stopband gains.
8
Figure 3.2 shows the amplitude and phase responses of the FIR filter designed by remez. The
phase response is zero throughout the passband and transition band. However, each zero-crossing
in the stopband results in a phase jump of π radians, so that the phase alternates between zero and
π in the stopband. This is typical of practical zero-phase filters.
Fig3.2 : Amplitude response and phase response of the length 11 zero-phase FIR lowpass filter in Fig.3.1.
We passed our original input sample through the zero phase filter generated, and here’s the
spectral analysis of the original and filtered sample showing the energies at lower frequencies are
kept intact while that of in higher frequencies are removed.
Fig 3.3 Spectrum of Original Signal and Filtered Signal (Zero-Phase)
9
We compute sqrt(Syy/Sxx) which is the magnitude response of the unknown filter. By doing this,
we loose phase information and hence it remains 0 as shown in graph with small glitches in
middle.
Fig 3.4 Magnitude and Phase Response of the Zero Phase filter
After we got the filter response, we tried to regenrate x by dividing y by magnitude response of
filter obtained and did an inverse DTFT on that. Through this, we could successfully regenerate
original sample, and energy spectrum looks exactly same as per the original sample as per the
spectral analysis.
Fig 3.5 Spectrum of Original Signal and Regenerated Signal (Zero-Phase)
10
3.1.2 Linear Phase Filter
For this, we used the same filter code without shifting it by (N-1)/2. Here is the spectrum of input
and filtered sample showing the energy in the higher frequency area are removed.
Fig 3.6 Spectrum of Original Signal and Filtered Signal (Linear-Phase)
The maginitude and phase response (almost zero as expected) obtained are as follows
Fig 3.7 Magnitude and Phase Response of the Linear Phase filter
11
We could regenrate the input sample but had some ringing sound. In the spectral analysis, we see
some energy at higher frequency (blue spots) are missing in the regenerated sample.
Fig 3.8 Spectrum of Original Signal and Regenerated Signal (Linear-Phase)
3.2 Different Signal for Sxx
For this part of simulation, we took a completely different sample to approximate Sxx. Below is
the spectral analysis of the original sample and approximated sample.
Fig 3.9 Spectrum of Original Signal and Used Signal for Sxx
12
3.2.1 Zero Phase Filter
Below is the magnitude and phase response which we could recover (some what corrupted).
Fig 3.10 Magnitude and Phase Response of the Zero Phase filter
After regeneration of the input sample, we found it similar to the input sample, but with lot of
noise being added in the background. From the spectral analysis, we see the input and
regenerated sample have similar enery spectrum but have lot of distortion in higher frequencies.
Fig 3.11 Spectrum of Original Signal and Regenerated Signal (Zero-Phase) (Using different signal for Sxx)
13
3.2.2 Linear Phase Filter
We repeated the same process considering a Linear Phase Filter Channel, and got a corrupted
magnitude and phase response for the filter.
Fig 3.12 Magnitude and Phase Response of the Linear Phase filter
The regenerated sample sounded much like the original sample but with lot of noise being added
in background. Also, from the spectral analysis, the energy spectrum looks quite similar with lot
of distortion in higher frequency area.
Fig 3.13 Spectrum of Original Signal and Regenerated Signal (Linear-Phase) (Using different signal for Sxx)
14
3.3 Approximated Sxx
Here we took a complete different input sample, and used three samples which was the same
speech but spoken by different speaker and at different timing. Here is the spectral analysis of
three samples with energy spectrum similar but different in sense of timing and frequency.
Fig 3.14 Spectrum of Sample 1,Sample 2 and Sample 3
To approximate Sxx, we took the average of the frequency components of their autocorrelation
values. This is because Sxx values for a human speech are nearly same, hence taking an average
of different samples.
Fig 3.15 Sxx Magnitude of Sample 1,Sample 2 and Sample 3
15
3.3.1 Zero Phase Filter
This is the spectrum of original sample, after being passed through low pass zero phase filter,
which enerdies removed at higher frequencies.
Fig 3.16 Spectrum of Original Signal and Filtered Signal (Zero-Phase)
Here’s the magnitude and phase response of the filter. It looks less corrupted and more close to
the original filter response as obtained in 3.1.1.
Fig 3.17 Magnitude and Phase Response of the Zero Phase filter
16
The regenerated sample sounded less noisy than that of 3.2.1. Also the energy spectrum is more
close to the original at lower frequencies.
Fig 3.18 Spectrum of Original Signal and Regenerated Signal (Zero-Phase) (Using Average of 3 samples for Sxx)
3.3.2 Linear Phase Filter
When passed through Linear Phase , it removes the energy at higher frequency.
Fig 3.19 Spectrum of Original Signal and Filtered Signal (Linear-Phase)
17
The magnitude response of the filter appears more closer to the original one that 3.1.2 than 3.2.2
Fig 3.20 Magnitude and Phase Response of the Linear Phase filter
The regenerated sample sounded less noisy than that of 3.2.2 case. Also through the spectral
analysis, enery spectrum at lower frequency are nearly same and less noisy than 3.2.2.
3.21 Spectrum of Original Signal and Regenerated Signal (Linear-Phase) (Using Average of 3 samples for Sxx)
18
4. CO�CLUSIO�
4.1 Concise Result
From the simulation, we could finally summarize following results
Values used of Sxx Filter Type Result
Original Sample
Zero Phase Regenerated Exact Input Sample
Linear Phase Regained Original Sample with feeble ringing
sound
Different Sample Zero Phase Regenerated Noisy Input Sample
Linear Phase Regenerated Noisy Input Sample
Average of various
Sample
Zero Phase Regenerated Less Noisy Input Sample
Linear Phase Regenerated Less Noisy Input Sample
4.2 Future Work
From the work done, we can have better approximation algorithms so as the regenerated sample
is more close both in terms of magnitude and phase, closer to the original sample. Also, as this
approach of System Identification has a major contraint of losing the phase response of the filter,
this technique cannot be used for general case, and hence lot of approximation on the filter
specification has to be done. For other filter like that of IIR filters such as Butterforth or
Elliptical filter, this technique could be used to recover the magnitude response of the sample, so
if we have a technique to predict the phase modification being added by the filter, we can recover
the original sample.
4.3 Experience
Working directly upon the filter characteristics, modifying its properties, playing with sound
samples, analyzing the sound spectrum and comparing various tradeoffs affecting equalization
characteristics gave us a through insight upon a real world problem. Also it gave us an
experience of implementing the theoritical aspect of Digital Signal Processing over an actual
application. Hence, we are kind of thankful to everyone especially Prof. Dan Ellis and TA Wei
Jiang, whose constant guidance and motivation saved our work to go into pitfalls.
19
5. REFERE�CES
[1] Digital Signal Processing – Sanjit Mitra
[2] Channel Equalization Techniques by Fernando Gregorio.
[3] http://en.wikipedia.org/wiki/Equalization
[4] Blind System Identification and Channel Equalization of IIR Systems without Statistical
Information, Signal Processing, IEEE Transactions on Acoustics, Speech, and Signal
Processing, Erwei Bai and Minyue Fu.
20
APPE�DIX
Code for 3.1.1, 3.1.2, 3.2.1, 3.2.2
num = 512*64; a = 0; %Start from the beginning (a=0), a can be 0~77482 [x,r] = wavread('mssp3.wav'); %ORIGINAL Sound [x2,r] = wavread('mssp2.wav'); %Another Sound x=x(a+1:a+num); % shorten the original sound(110250) into (32768) x2=x2(a+1:a+num); N = 11; % filter length - must be odd b = [0 0.1 0.2 0.5]*2; % band edges M = [1 1 0 0 ]; % desired band values h = remez(N-1,b,M); % Remez multiple exchange design hh = h(6:N); % Shift (N-1)/2=5 samples to make h zero-phase hh(7:11) = 0; % Pass it through the filter y = filter(hh,1,x); % Zero Phase Ly = filter(h,1,x); % Linear Phase % Autocorrelation rxx=xcorr(x(1:num)); %AutoCorrelation:using Original signal as estimated x rxx2=xcorr(x2(1:num)); %AutoCorrelation:using Different signal as estimated x ryy=xcorr(y); rLyy=xcorr(Ly); rxysize = size(rxx); num1 = 2^ceil(log2(rxysize(1))); %make num into even Ex.65535 into 65536 % Do FFT to get frequency response of autocorrelation sxx = fft(rxx,num1); sxx2= fft(rxx2,num1); syy = fft(ryy,num1); sLyy = fft(rLyy,num1); Y = fft(y,num1); LY =fft(Ly,num1); for i = 1 : num1 if (syy(i) == 0) XX(i) = 999999999999999; XX2(i) = 999999999999999; else
%|!�i | &= syy(i)/sxx(i); XX(i)=Y(i)/H(i) XX(i) = Y(i)*sqrt(abs(sxx(i)/syy(i))); XX2(i)= Y(i)*sqrt(abs(sxx2(i)/syy(i))); end end for i = 1 : num1 if (sLyy(i) == 0) LXX(i) = 999999999999999;
21
LXX1(i) = 999999999999999; else
%%|!�i | &= syy(i)/sxx(i); XX(i)=Y(i)/H(i) LXX(i) = LY(i)*sqrt(abs(sxx(i)/sLyy(i))); LXX1(i) = LY(i)*sqrt(abs(sxx2(i)/sLyy(i))); end end xx = ifft(XX,num1); xx2 = ifft(XX2,num1); Lxx= ifft(LXX,num1); Lxx1= ifft(LXX1,num1); % Zero-Phase Filter case soundsc(x,r); %Original Sound soundsc(y,r); %Original Sound passed through Zero-Phase Filter soundsc(xx,r); %Regenerated signal by using original signal as estimated x soundsc(xx2,r); %Regenerated signal by using other signal as estimated x % Linear-Phase Filter case soundsc(x,r); %Original Sound soundsc(Ly,r); %Original Sound passed through Linear-Phase Filter soundsc(Lxx,r); %Regenerated signal by using original signal as estimated x soundsc(Lxx1,r);%Regenerated signal by using other signal as estimated x
Code for 3.3.1, 3.3.2
num = 512*64; [x,r] = wavread('sf1_cln.wav'); %ORIGINAL Sound [x1,r] = wavread('sf2_cln.wav'); %BASE Sound [x2,r] = wavread('sf3_cln.wav'); %BASE Sound x=x(1:num); N = 11; % filter length - must be odd b = [0 0.1 0.2 0.5]*2; % band edges M = [1 1 0 0 ]; % desired band values h = remez(N-1,b,M); % Remez multiple exchange design hh = h(6:N); % Shift (N-1)/2=5 samples to make h zero-phase hh(7:11) = 0; % Pass it through the filter y = filter(hh,1,x); % Zero Phase Ly = filter(h,1,x); % Linear Phase % Autocorrelation rxx=xcorr(x(1:num)); %AutoCorrelation: ORIGINAL Sound rxx1=xcorr(x1(1:num)); %AutoCorrelation: BASE Sound rxx2=xcorr(x2(1:num)); %AutoCorrelation: BASE Sound ryy=xcorr(y); rLyy=xcorr(Ly); rxysize = size(rxx); num1 = 2^ceil(log2(rxysize(1))); %make num into even Ex.65535 into 65536 % Do FFT to get frequency response of autocorrelation sxx = fft(rxx,num1); sxx1= fft(rxx1,num1); sxx2= fft(rxx2,num1); sxx3= (sxx+sxx1+sxx3)/3; %Average the original and base sound as estimated Sxx syy = fft(ryy,num1); sLyy = fft(rLyy,num1);
22
Y = fft(y,num1); LY =fft(Ly,num1); % Zero-Phase Filter for i = 1 : num1 if (syy(i) == 0) XX(i) = 999999999999999; else
%|!�i | &= syy(i)/sxx(i); XX(i)=Y(i)/H(i) XX(i) = Y(i)*sqrt(abs(sxx3(i)/syy(i))); end end % Linear-Phase Filter for i = 1 : num1 if (sLyy(i) == 0) LXX(i) = 999999999999999; else
%%|!�i | &= syy(i)/sxx(i); XX(i)=Y(i)/H(i) LXX(i) = LY(i)*sqrt(abs(sxx3(i)/sLyy(i))); end end xx = ifft(XX,num1); Lxx= ifft(LXX,num1); % Zero-Phase Filter case soundsc(x,r); %Original Sound soundsc(y,r); %Original Sound passed through Zero-Phase Filter soundsc(xx,r); %Regenerated signal by using average spectrum as Sxx % Linear-Phase Filter case soundsc(x,r); %Original Sound soundsc(Ly,r); %Original Sound passed through Linear-Phase Filter soundsc(Lxx,r); %Regenerated signal by using average spectrum as Sxx
Top Related